SECURITY PINSK15.14

K15

DOORS

01.06.2019

Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com

CONTENTS

1. Security pins n° 4208-141, -141B, -141D, -141E, -141G, -141R ............... K15.14.03

2. Security pin n° 4208-142G ................................................. K15.14.05

3. Security pin n° 4208-143 .................................................... K15.14.07

4. Security pin n° 4208-143B ................................................. K15.14.09

5. Security pin n° 4208-143C ..................................................K15.14.12

6. Long security pin n° 4208-143D and n° 4208-143F ...........K15.14.13

7. Long security pin n° 4208-142E ..........................................K15.14.15

8. Long security pin n° 4208-142F ..........................................K15.14.17

K15.14.02 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

1. Security pins n° 4208-141, -141B, -141D, -141E, -141G, -141RGeneral

• The security pin is suitable as extra security for windows or doors: - The screw engages into the frame section and works as anti-lift pin. - The screw collar prevents frame and vent from being pushed together.

• The security pin is screwed to the vent and can be used on sections with or without vent groove. The collar of the adjustment screw is screwed up against the frame.

• Finish: - Plate: satin anodised aluminium - Adjustment screw and collar: stainless steel

n° 4208-141Bn° 4208-141

n° 4208-141En° 4208-141D

HINGES AND SECURITY PINS K15.14.03

SECURITY PINS

K15.14

Installation examples

• Adjustment range: 10 mm.

• Dimension A: - Minimum: 15 mm - Maximum: 25 mm

• The diameter of drilling hole B in the frame section depends on: - The section combination. - The position of the security pin in the sections: the further the security pin from the pivot point of the door, the smaller the drilling hole.

n° 4208-141G n° 4208-141R

Without vent grooveWith vent groove

K15.14.04 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

2. Security pin n° 4208-142GGeneral

• The security pin is suitable as extra security for doors: - The pin engages into the frame section and works as anti-lift pin. - The fixing block prevents frame and vent from being pushed together.

• The security pin set is especially suitable for flush doors without vent and frame groove with an inside gap of 16 mm, suitable to use the Sobinco Rollenband.

• The set also contains the fixing screws and the blind rivnuts.• SKG approved, 2 stars.• Finish:

- Fixing block: satin anodised aluminium - Pin: stainless steel

Hinges• The number and position of the hinges depends on the vent dimensions, the vent weight and the application

circumstances. Therefore we refer to the chapters about door hinges.

n° 4208-142G

Blind rivnut M5x13 UPO30

Fixing screw M5x25 DIN965

positionsecurity pin

HINGES AND SECURITY PINS K15.14.05

SECURITY PINS

K15.14

Installation• The security pin is mounted on the vent and fixed

with: - Metric screws M5x25 DIN965 - Blind rivnuts with countersunk head M5x13 UPO30

• The vertical positioning of the security pins depends on the used hinges.

• The positioning will also be different when mounting multiple hinges.

• Installation example:

Door X1(mm)

X2(mm)

X3(mm)

Y1(mm)

Y2(mm)

Y3(mm)

With Sobinco RollenbandA1 365+K Fh/2-465 450 315 Fh/2-465 400-LA2 670+K Fh/2-590 450 620 Fh/2-590 400-LA3 365+K Fh/2-625 450 315 Fh/2-625 400-LA4 670+K Fh/2-635 450 620 Fh/2-635 400-L

Frame Vent

Floor

L = distance between floor and bottom edge of the vent

K15.14.06 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

3. Security pin n° 4208-143General

• The security pin is suitable as extra security for windows: - The pin engages into the frame section and works as anti-lift pin. - The fixing block prevents frame and vent from being pushed together.

• The security pin is SKG approved, 2 stars.

• The security pin n° 20300-771 is black anodised.

• Finish: - Fixing block: satin (or black) anodised aluminium - Pin: stainless steel

Profiles

• The security pins are intended for windows with a eurogroove, but they are also possible for doors with or without vent groove.

• For doors we refer to security pin n° 4208-143B: see page K15.14.09.

n° 4208-143n° 20300-771

B(mm)

C(mm)

D(mm)

E(mm)

13.8 4.2 18 1.512.5 3.9 16.8 1.512.1 2.9 15.3 1.510 4.2 14.8 1.514.1 4.2 18.5 2.513.5 3.5 17.5 2.5

HINGES AND SECURITY PINS K15.14.07

SECURITY PINS

K15.14

Installation

• The security pin is slid into the vent groove and then fixed with the screws.

• Note: the milling depends on the position of the security pin in the sections as well as on the applied hinges (=position rotation point).

• This installation applies when using the Chrono hinges n° 26140-750 and 26140-760 for side hung open in windows.

4.8x25DIN 7504P

= position security pin

K15.14.08 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

4. Security pin n° 4208-143BGeneral

• The security pin is suitable as extra security for doors: - The pin engages into the frame section and works as anti-lift pin.

- The fixing block prevents frame and vent from being pushed together.

• The security pin is SKG approved, 2 stars.

• Finish: - Fixing block: satin anodised aluminium - Pin: stainless steel

Profiles• The security pins are used for doors with a

eurogroove, but they are also possible for doors without vent groove.

Installation example with hinge type 2800

HINGES AND SECURITY PINS K15.14.09

SECURITY PINS

K15.14

Installation possibilities• The number and position of the hinges depends on the vent dimensions, the vent weight and the application

circumstances. Therefore we refer to the chapters about door hinges.

With the 2-part clampable hinges series 2800

With the 3-part clampable hinge n° 83201-1

With the 2-part face fixed hinges

With the 3-part face fixed hinges

position security pin

K15.14.10 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

Installation

• The vent height Fh is measured from the floor.

• Dimension L is the free space between vent and floor surface.

• The installation of the hinges depends on the type of hinge, see: - Chapter K15.11. : 2-part clampable hinges series 2800 - Chapter K15.11. : 3-part clampable hinge n° 83201-1 - Chapter K15.13. : face fixed hinges

4.8x25DIN 7504P

Frame Vent

Floor

Door X1(mm)

X2(mm)

X3(mm)

Y1(mm)

Y2(mm)

Y3(mm)

With 2-part clampable hinges series 2800A1 320+K Fh/2-305 290 270 Fh/2-305 240-LA2 570+K Fh/2-430 290 520 Fh/2-430 240-LA3 320+K Fh/2-465 290 270 Fh/2-465 240-LA4 570+K Fh/2-430 290 520 Fh/2-430 240-L

With 3-part clampable hinges n° 83201-1B1 365+K Fh/2-465 450 315 Fh/2-465 400-LB2 670+K Fh/2-590 450 620 Fh/2-590 400-LB3 365+K Fh/2-625 450 315 Fh/2-625 400-LB4 670+K Fh/2-635 450 620 Fh/2-635 400-L

With 2-part and 3-part face fixed hingesC1,D1 340+K Fh/2-340 340 290 Fh/2-340 290-LC2,D2 640+K Fh/2-490 340 590 Fh/2-490 290-LC3,D3 340+K Fh/2-475 340 290 Fh/2-475 290-LC4,D4 640+K Fh/2-475 340 590 Fh/2-475 290-L

HINGES AND SECURITY PINS K15.14.11

SECURITY PINS

K15.14

5. Security pin n° 4208-143C• The security pin is suitable as extra security for doors:

- The pin engages into the frame section and works as anti-lift pin. - The fixing block and the collar prevent frame and vent from being pushed together.

• The security pin is SKG approved, 2 stars.

• Finish: - Fixing block: satin anodised aluminium - Pin and collar: stainless steel

K15.14.12 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

6. Long security pin n° 4208-143D and n° 4208-143FGeneral

• The security pin is suitable as extra security for doors: - The pins engage into the frame section and work as anti-lift pins.

- The fixing block prevents frame and vent from being pushed together.

• The security pin set is especially suitable for rebated doors.

• The set contains all parts and screws.

• The security pin is SKG approved, 3 stars.

• You should fit this security pin in pairs on a door to achieve RC3.

• Finish: - Fixing block: satin anodised aluminium

- Pins, keep and screws: stainless steel

4.8x32 DIN 7504PM5x16 DIN 965

M5x12.5

Order code A (mm) B (mm)4208-143D 660 4804208-143F 450 270

HINGES AND SECURITY PINS K15.14.13

SECURITY PINS

K15.14

Installation• The security pins are used for doors with

a eurogroove in combination with 2-part (series 2800) or 3-part (n° 83201-1) Eurohinges.

• The vertical position of the security pins depends on the used hinges.

• The drawing applies to the installation of one 3-part Eurohinge at the top and at the bottom.

• When mounting other and/or multiple hinges, the positioning will be different and the minimum vent height can also increase.

• Profile dimensions

• Cross section

4.8x32DIN 7504P

M5x16DIN 965

Blind rivnut withcountersunk headM5x12.5

Order code B (mm)4208-143D 4804208-143F 270

L = distance between floor and bottom edge of the vent

Frame Vent

Floor

K15.14.14 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

7. Long security pin n° 4208-142EGeneral

• The security pin is suitable as extra security for doors: - The pins engage into the frame section and work as anti-lift pins.

- The fixing block prevents frame and vent from being pushed together.

• The security pin set is especially suitable for flush doors without vent and frame groove with an inside gap of 20 mm, suitable to use the Sobinco Rollenband.

• Set n° 4208-142E contains all parts and screws.• The security pin is SKG approved, 3 stars.• You should fit this security pin in pairs

on a door to achieve RC3.

• Finish: - Fixing block: satin anodised aluminium.

- Clamping plate: aluminium. - Pins, keep and screws: stainless steel.

M5x30 DIN 965

M5x16 DIN 965

M5x12,5

HINGES AND SECURITY PINS K15.14.15

SECURITY PINS

K15.14

Installation• The vertical positioning of the security

pins depends on the used hinges.• The drawing applies to the installation

of one Sobinco Rollenband at the top and at the bottom.

• When mounting other and/or multiple hinges, the positioning will be different and the minimum vent height can also increase.

• Profile dimensions

• Clamping plate

M5x30DIN 965M5x16DIN 965

Blind rivnut with countersunk headM5x12.5

M5x30DIN 965

Frame Vent

Floor

L = distance between floor and bottom edge of the vent

K15.14.16 HINGES AND SECURITY PINS

SECURITY PINS

K15.14

8. Long security pin n° 4208-142FGeneral

• The security pin is suitable as extra security for doors: - The pins engage into the frame section and work as anti-lift pins.

- The fixing block prevents frame and vent from being pushed together.

• The security pin set is especially suitable for flush doors without vent and frame groove with an inside gap of 20 mm, suitable to use the Sobinco Rollenband.

• Set n° 4208-142F contains all parts and screws.• The security pin is SKG approved, 3 stars.• You should fit this security pin in pairs

on a door to achieve RC3.

• Finish: - Fixing block: satin anodised aluminium.

- Clamping plate: aluminium. - Pins, keep and screws: stainless steel.

M5x25 DIN 965

M5x18 DIN 965

M5x13

HINGES AND SECURITY PINS K15.14.17

SECURITY PINS

K15.14

Installation• The vertical positioning of the security pins depends on the used hinges.• The drawing applies to the installation of one Sobinco Rollenband at the top and at the bottom.• When mounting other and/or multiple

hinges, the positioning will be different and the minimum vent height can also increase.

• Profile dimensions

• Clamping plate

M5x30DIN 965M5x16DIN 965

Blind rivnut with countersunk headM5x12.5

M5x30DIN 965

Frame Vent

Floor

L = distance between floor and bottom edge of the vent

K15.14.18 HINGES AND SECURITY PINS

SECURITY PINS

K15.14