Download EEE 2014-2015 syllabus

Bangabandhu Sheikh Mujibur Rahman Science and Technology University

(BSMRSTU)

Faculty of Engineering

Department of Electrical & Electronic Engineering (EEE)

Session: 2014-2015

Department of Electrical & Electronic Engineering (EEE) Undergraduate Studies

Syllabus for B.Sc. Engineering Session: 2014 – 2015

Chapter 1 Courses for B.Sc. in Electrical and Electronic Engineering

1.1 Course Identification System: Each course is designated by a three-letter symbol for department abbreviation followed by a three-digit number to characterize the course. An extra letter may be used after the three digits to specify the department taking the non-major course Course Number: The three-digit number will be used as follows- First digit: The first digit of the three digit number corresponds to the Class-year. Second Digit: If the second digit is less than five (0 to 4) that indicates first semester and greater than four (5 to 9) indicates second semester. Third Digit: The third digit is reserved to identify different areas within a department. A department may use the digits 0 and 2 for major theory, 1 and 3 for major practical, 4 and 6 for minor theory, 5 and 7 for minor practical, 8 for thesis/projects/others and 9 for viva-voce. XXX Course Title

The second digit (0 to 4) indicates semester-I/1st Semester

(5 to 9) indicates semester-II/2nd semester

1st digit the class, year

Three letter Dept. identification code

0 1

2 3

4 5

6 7

8 9

Major Theory

Major LAB

Non-major Theory

Non-major LAB

Thesis/Project/Others

Viva-voce

1.2 Credit requirements

The minimum hours to be completed for obtaining the degree of B.Sc. Engineering in Electrical and Electronic Engineering is 202 of which 118 hours are for theoretical courses, 84 hours for laboratory courses and two weeks Industrial Training with a total credit of 160.0. A viva-voce board will be arranged in each semester depending on practical courses only which will be added to lab credit. The semester-wise distribution of credits of different years is listed below:

Year Semester Theory Hour

Lab Hour

Total Hour

Total Credit

1 1 2 2 3 3 4 4

1 2 1 2 1 2 1 2

14 17 14 15 16 15 15 12

8.50 7.50 9.00 10.5 10.5 13.5 11.0 13.5

22.5 24.5 23.0 25.5 26.5 28.5 26.0 25.5

18.25 20.75 18.50 20.25 21.25 21.00 20.50 18.75

Sub-total 118 84 202 159.25 Two weeks Industrial Training 0.75

Total 160.0 1.3 Distribution of Courses

SlNo. CourseType Credit % 1 Major Course

Core Courses Theory 67 41.87

Lab 28.5 17.81 2 Elective Courses

Theory 15 9.38 Lab 3.75 2.34

Sub-Total 114.25 71.40 3 Non-Major Courses

a Humanities Theory 8 5.00 Lab 1 0.63 Sub-Total 9 5.63

b Basic Sciences Theory 26 16.25

Lab 1.5 0.94

Sub-Total 27.5 17.19 c Basic Engg. Theory 6 3.75

Lab 3.25 2.03 Sub-Total 9.75 5.78

1.4 Core Courses Some of the core courses are identified as pre-requisite courses. A pre-requisite course is one which is required to be completed before some other course(s) can be taken. Any such course, on which one or more subsequent courses build up, may be offered in each of the two regular semesters.

1.4.1 Core Courses (EEE)

Sl. No.

Course Number

Course Title Credit Hour

1 EEE 100 Electrical Circuits 3.0 2 EEE 101 Electrical Circuits Lab. 1.5 3 EEE 150 Electrical Circuits 3.0 4 EEE 151 Electrical Circuits Lab. 1.5 5 EEE 201 Electrical Service Design 0.75 6 EEE 210 Electronics 3.0 7 EEE 211 Electronics Lab. 1.5 8 EEE 220 Electrical Machine 3.0 9 EEE 221 Electrical Machine Lab. 1.5

10 EEE 250 Measurement and Instrumentation 3.0 11 EEE 251 Measurement and Instrumentation Lab 0.75 12 EEE 253 Electrical and Electronic Circuit Simulation Lab 1.5 13 EEE 260 Electronics 3.0 14 EEE 261 Electronics Lab. 1.5 15 EEE 270 Electrical Machine 3.0 16 EEE 271 Electrical Machine Lab. 1.5 17 EEE 280 Electromagnetics 3.0 18 EEE 300 Signals and Linear Systems 3.0 19 EEE 308 Project 0.75 20 EEE 310 Digital Electronics 3.0 21 EEE 311 Digital Electronics Lab. 1.5 22 EEE 320 Power Electronics 3.0 23 EEE 321 Power Electronics Lab. 1.5 24 EEE 340 Numerical Methods for Engineering 3.0 25 EEE 341 Numerical Methods for Engineering Lab 1.5 26 EEE 362 Electronic Circuit for Communication System 2.0 27 EEE 368 Industrial Training 0.75 28 EEE 380 Communication Theory 4.0 29 EEE 381 Communication Theory Lab. 1.5 30 EEE 382 Control System 3.0 31 EEE 383 Control System Lab. 1.5 32 EEE 390 Microprocessor, Interfacing and System design 3.0 33 EEE 391 Microprocessor, Interfacing and System design

Lab. 1.5

34 EEE 392 Power System 3.0 35 EEE 393 Power System Lab. 1.5 36 EEE 400 Digital Signal Processing 3.0 37 EEE 401 Digital Signal Processing Lab. 1.5 38 EEE 408 Project and Thesis 1.0 39 EEE 412 Electrical Properties of Materials 3.0 40 EEE 458 Project and Thesis 3.0 41 EEE 492 Microcontroller and PLC based System Design 3.0 42 EEE 493 Microcontroller and PLC based System Design

Lab. 1.5

43 EEE 402 Power System Protection 3.0 44 EEE 403 Power System Protection Lab. 1.5

Total 95.5

1.4.2 Core Courses (Humanities)

Sl. No.

Course Number Course Title Credit

Hour 1 ENG 104 Technical English 2.0 2 ENG 105 Technical English Lab. 1.0 3 AIS 214 Industrial Management and Accountancy 2.0 4 ECO 306 Economics 2.0 5 SOC 304 Sociology and Professional Ethics 2.0

Total 9.0 1.4.3 Core Courses (Mathematics)

Sl. No.


Hour 1 MAT 104 Engineering Mathematics

(Differential Calculus & Integral Calculus) 3.0

2 MAT 106 Engineering Mathematics (Linear Algebra & Coordinate Geometry)

3.0

3 MAT 154 Engineering Mathematics (Ordinary & Partial Differential Equations)

3.0

4 MAT 204 Engineering Mathematics V (Complex Variable & Vector Analysis)

3.0

5 MAT 254 Engineering Mathematics V (Fourier Analysis & Laplace Transformation)

3.0

Total 15.0 1.4.4 Core Courses (Physics)

Sl. No.


Hour 1 PHY 114 Physics

(Waves and Oscillations, Optics and Thermal Physics)

3.0

2 PHY 115 Physics Lab. 0.75 3 PHY 164 Physics

(Modern Physics, Nuclear Physics and Quantum Mechanics)

2.0

Total 5.75 1.4.5 Core Courses (Chemistry)

Sl. No.


Hour 1 AEC 184 Chemistry 3.0 2 AEC 185 Chemistry Lab. 0.75

Total 3.75 1.4.6 Core Courses (CE)

Sl. No.


Hour 1 CE 125 Engineering Drawing 1.0

Total 1.0

1.4.7 Core Courses (ME)

Sl. No.


Hour 1 ME 204 Mechanical Engineering Fundamentals 3.0 2 ME 205 Mechanical Engineering Fundamentals Lab. 0.75

Total 3.75 1.4.8 Core Courses (CSE)

Sl. No.


Hour 1 CSE 194 Programming Language 3.0 2 CSE 195 Programming Language Lab. 1.5

Total 4.5 1.4.9 Core Course (Statistics)

Sl. No.


Hour 1 STA 156 Statistics for Engineers 3.0

Total 3.0 1.5 Elective Courses From Year-4, Semester-1, Department of EEE starts offering elective courses under 2major groups viz. Power, Electronics and Communication. Rules for distributing major groups are as follows: 1. Students will be assigned one of the two groups as major by taking written options from the

students. For regular students, this will be done in Year-3, Semester-2. 2. Maximum number of students in any group as major will be N/2, where N is the number of students

in a batch. 3. Major group assignment will be based on options and CGPA of first five terms from Year-1,

Semester-1 to Year-3, Semester-1. 4. A student will have to take 5 elective theory courses from the respective major group. 5. Students will be assigned their Year-4 projects/ theses from the area of their respective major group. 6. Maximum class size of an elective course for regular students will be (N/2). However, a student who

has previously failed in an elective course will be allowed to re-regular regardless of the class size. 7. In case of any unforeseen situation or ambiguity, the Department will take an appropriate decision.

1.5.1 Power Group

Sl. No

Course Number Course Name Credit

Hour 1 EEE 410 Power System II 3.0 2 EEE 411 Power System II Lab 1.5 3 EEE 430 High voltage engineering 3.0 4 EEE 460 Electrical Machine III 3.0 5 EEE 461 Electrical Machine III Lab 1.5 6 EEE 470 Non-conventional Energy 3.0 7 EEE 471 Non-conventional Energy Lab. 0.75 8 EEE 472 Power Plant Engineering and Economy 3.0

1.5.2 Electronics and Communication Group

Sl. No.

Course Number Course Name Credit

Hour 1 EEE 420 Microwave Engineering 3.0 2 EEE 421 Microwave Engineering Lab. 1.0 3 EEE 432 Digital Communication 3.0 4 EEE 433 Digital Communication Lab. 1.0 5 EEE 440 Optoelectronics 3.0 6 EEE 450 VLSI 3.0 7 EEE 451 VLSI Lab 1.5 8 EEE 452 Optical Fiber Communication 3.0 9 EEE 462 Computer Networks & Data Communication 3.0

10 EEE 480 Mobile Cellular Communication 3.0 11 EEE 481 Mobile Cellular Communication Lab 0.75 12 EEE 482 Telecommunication Engineering 3.0 13 EEE 490 Biomedical Engineering 3.0

Chapter 2 Course Offering Courses are offered to the students as per following arrangement:

Year-1 Semester-1

Course No.

Course Title Contact hrs/week

Credit

EEE 100 Electrical Circuits 3 3.0 EEE 101 Electrical Circuits I Lab. 3 1.5 MAT 104 Engineering Mathematics

(Differential Calculus & Integral Calculus) 3 3.0

MAT 106 Engineering Mathematics (Linear Algebra & Coordinate Geometry)

3 3.0

ENG 104 Technical English 2 2.0 ENG 105 Technical English Lab. 2 1.0 PHY 114 Physics

(Waves and Oscillations, Optics and Thermal Physics)

3 3.0

PHY 115 Physics Lab. 3/2 0.75 CE 125 Engineering Drawing 2 1.0 Viva Voce(EEE 101, PHY 115, CE 125 and ENG 105) Total 18.25

Year-1 Semester-2

Course No.


Credit

EEE 150 Electrical Circuits 3 3.0 EEE 151 Electrical Circuits Lab. 3 1.5 PHY 164 Physics

(Modern Physics, Nuclear Physics and Quantum Mechanics)

2 2.0

MAT 154 EngineeringMathematics (Ordinary & Partial Differential Equations)

3 3.0

STA 156 Statistics for Engineers 3 3.0 AEC 184 Chemistry 3 3.0 AEC 185 Chemistry Lab. 3/2 0.75 CSE 194 Programming Language 3 3.0 CSE 195 Programming Language Lab. 3 1.5 Viva Voce (EEE 151, CSE 195 and AEC 185) Total 20.75

Year-2 Semester-1

Course No.


Credit

EEE 201 Electrical Service Design 3/2 0.75 EEE 210 Electronics 3 3.0 EEE 211 Electronics Lab. 3 1.5 EEE 220 Electrical Machine 3 3.0 EEE 221 Electrical Machine Lab. 3 1.5 ME 204 Mechanical Engineering Fundamentals 3 3.0 ME 205 Mechanical Engineering Fundamentals Lab. 3/2 0.75 MAT 204 Engineering Mathematics V

(Complex Variable, & Vector Analysis) 3 3.0

AIS 214 Industrial Management and Accountancy 2 2.0 Viva Voce (EEE 211, EEE 221, ME 205 and EEE 201) Total 18.50

Year-2 Semester-2

Course No.


Credit

EEE 250 Measurement and Instrumentation 3 3.0 EEE 251 Measurement and Instrumentation Lab 3/2 0.75 EEE 253 Electrical and Electronic Circuit Simulation Lab 3 1.5 EEE 260 Electronics 3 3.0 EEE 261 Electronics Lab. 3 1.5 EEE 270 Electrical Machine 3 3.0 EEE 271 Electrical Machine Lab. 3 1.5 EEE 280 Electromagnetics 3 3.0 MAT 254 Engineering Mathematics V

(Fourier Analysis & Laplace Transformation) 3 3.0

Viva Voce (EEE 261, EEE 271, EEE 251, EEE 253) Total 20.25

Year-3 Semester-1

Course No.


Credit

EEE 300 Signals and Linear Systems 3 3.0 EEE 308 Project 3/2 0.75 EEE 310 Digital Electronics 3 3.0 EEE 311 Digital Electronics Lab. 3 1.5 EEE 320 Power Electronics 3 3.0 EEE 321 Power Electronics Lab. 3 1.5 EEE 340 Numerical Methods for Engineering 3 3.0 EEE 341 Numerical Methods for Engineering Lab. 3 1.5 SOC 304 Sociology and Professional Ethics 2 2.0 ECO 306 Economics 2 2.0 Viva Voce(EEE 311, EEE 321 and EEE 341) Total 21.25

Year-3 Semester-2

Course No.


Credit

EEE 362 Electronic circuit for communication system 2 2.0 EEE 368 Industrial Training* 0.75 EEE 380 Communication Theory 4 4.0 EEE 381 Communication Theory Lab. 3 1.5 EEE 382 Control System 3 3.0 EEE 383 Control System Lab. 3 1.5 EEE 390 Microprocessor, Interfacing and System design 3 3.0 EEE 391 Microprocessor, Interfacing and System design Lab 3 1.5 EEE 392 Power System 3 3.0 EEE 393 Power System Lab. 3 1.5 Viva Voce (EEE 381, EEE 383, EEE 391 and EEE 393) Total 21.75

*EEE 368 Industrial Training: Students will be attached with the industries/service agencies for two weeks after completing their Third year second semester (before starting Fourth year) to gain practical knowledge. Without satisfactory completion of this course the student will not fulfill the requirements of B. Sc. Engineering Degree.

Year-4 Semester-1

Course No. Course Title Contact hrs/week

Credit

EEE 408 Project and Thesis 1.0 EEE 400 Digital Signal Processing 3 3.0 EEE 401 Digital Signal Processing Lab 3 1.5 EEE 402 Power System protection 3 3.0 EEE 403 Power System protection Lab 3 1.5 EEE **** Elective I 3 3.0 EEE **** Elective I Lab. 3 1.5 EEE **** Elective II 3 3.0 EEE 412 Electrical Properties of Materials 3 3.0 Viva Voce (EEE 401, EEE 403 and Elective I Lab) Total 20.5

Year-4 Semester-2

Course No. Course Title Contact hrs/week

Credit

EEE 458 Project and Thesis 3.0 EEE 492 Microcontroller and PLC based System Design 3 3.0 EEE 493 Microcontroller and PLC based System Design Lab 3 1.5 EEE **** Elective III 3 3.0 EEE **** Elective III Lab 3 1.5 EEE **** Elective IV 3 3.0 EEE **** Elective IV Lab 3/2 0.75 EEE **** Elective V 3 3.0 Viva Voce (EEE 493, Elective III Lab and Elective IV Lab) Total 18.75

2.2 Elective Course divisions Five elective courses (Elective I – Elective V) are offered to the students according to the following list. Elective I

Group Course Number Course Title Credit Hour

Indiv. Total Power EEE 410 Power System II 3.0 4.5

EEE 411 Power System II Lab 1.5 Electronics &Communication

EEE 432 Digital Communication 3.0 4.5 EEE 433 Digital Communication Lab 1.5 EEE 420 Microwave Engineering 3.0 4.5 EEE 421 Microwave Engineering Lab. 1.5

Elective II

Group Course Number Course Title Credit

Hour Power EEE 430 High voltage engineering 3.0 Electronics & Communication

EEE 440 Optoelectronics 3.0

Elective III

Group Course Number

Course Title Credit Hour Indiv. Total

Power EEE 460 Electrical Machine III 3.0 4.5 EEE 461 Electrical Machine III Lab 1.5

Electronics & Communication

EEE 450 VLSI 3.0 4.5 EEE 451 VLSI Lab 1.5

Elective IV

Group Course Number

Course Title Credit Hour Indiv. Total

Power EEE 470 Non-Conventional Energy 3.0 3.75 EEE 471 Non-Conventional Energy

Lab 0.75


EEE 480 Mobile Cellular Communication

3.0 3.75

EEE 481 Mobile Cellular Communication Lab

0.75

Elective V

Group Course Number Course Title Credit

Hour Power EEE 472 Power Plant Engineering and

Economy 3.0


EEE 482 Telecommunication Engineering 3.0 EEE 452 Optical Fiber Communication 3.0 EEE 462 Computer Networks & Data

Communication 3.0

EEE 490 Biomedical Engineering 3.0

3.1 Core Courses offered by the Department of EEE

Year-1 Semester-1 EEE 100 Electrical Circuits I 3 Credits, 3 hours/week Circuit Variables and Elements: Voltage, current, power, energy, independent and dependent sources, resistance. Basic Laws of Electrical Circuits: Ohm’s law, Kirchoff’s Current Law (KCL) and Kirchoff’s Voltage Law (KVL). Simple Resistive Circuits: Series and parallel circuits, voltage and current division, Source transformation, wye-delta transformation. Techniques of Network Analysis: Nodal and Mesh analysis including super node and super mesh. Network Theorems: Thevenin’s, Norton’s and superposition theorems with applications in circuits having independent and dependent sources, maximum power transfer condition and reciprocity theorem. Energy Storage Elements: Inductors and capacitors, their characteristics, series-parallel combination of inductors and capacitors. Alternating Current Basics: Instantaneous,average and R.M.S values, form factor, peak factor , effective current and voltage, average power, phasors and complex quantities, impedance, real, reactive and apparent power, power factor,power factor improvement Responses of RL and RC Circuits: Natural and step responses. Magnetic Quantities and Variables: Flux, permeability and reluctance, magnetic field strength, magnetic potential, flux density, magnetization curve, Laws in magnetic circuits: Ohm’s law and Ampere’s circuital law. Series, parallel and series-parallel magnetic circuits. Book Recommended: 1. Introductory Circuit Analysis – Robert L.Boylestad 2. Electric Circuits – Nelson and Reidel 3. Fundamentals of Electric Circuits- C. K. Alexander, M. N O.Sadiku 4. Linear Electric Circuits-W.L.Cassell 5. Introduction to Electric Circuits-Richard C. Dorf, James A. Svoboda EEE 101 Electrical Circuits I Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 100.

Chapter 3 Course Contents

MAT 104 Engineering Mathematics I (Differential Calculus & Integral Calculus) 3 Credits, 3 hours/week Differential Calculus: Limits, continuity and differentiability.Successive differentiation of various types of functions. Leibnitz’s theorem, Rolle’s theorem, Mean value theorem, Taylor’s and McLaurin’s theorems in finite and infinite forms. Lagrange’s form of remainders.Cauchy’s form of remainders.Expansion of functions, evaluations of indeterminate forms of L’Hospital’srule.Partialdifferentiation.Euler’stheorem.Tangent and normal.Sub tangent and subnormal in Cartesian and polar co-ordinates. Determination of maximum and minimum values of functions. Curvature, Asymptotes, curve tracing. Integral Calculus: Definition, Integration by the method of substitution, integration by parts.Standard Integrals.Integration by successive reduction.Definite Integrals, its properties and use in summing series.Walli’sformulae.Improper integrals. Beta function and Gamma function, Area under a plane curve and area of a region enclosed by two curves in Cartesian and polar co-ordinates, Trapezoidal and Simpson’s rule, Volumes and surface areas of solids of revolution. MAT 106 Engineering Mathematics II (Linear Algebra & Coordinate Geometry) 3 Credits, 3 hours/week Linear Algebra: Introduction to systems of linear equations.Gaussian elimination.Definition of matrices.Algebra of matrices. Transpose of a matrix and inverse of matrix. Factorization, Determinants. Quadratic forms. Matrix polynomials.Euclidean n-space.Linear transformation from IRn to IRm.Properties of Linear transformation from IRn to IRm.Real vector spaces and subspaces.Basis and dimension.Rank and nullity.Inner product spaces.Gram-Schmidt process and QR-decomposition.Eigenvalues and eigenvectors.Diagonalization.Lineartransformations.Kernel and Range.Application of linear algebra to electric networks. Coordinate Geometry: Coordinate Geometry of 2-dimension-change of axis, Transformation of coordinates, Simplification of equations of curves. Coordinate geometry of 3 dimension system of coordinates, distance between two points, section formula, projection, direction cosines, equations of planes and lines. ENG 104 Technical English 2 Credits, 2 hours/week Grammar (18%): Grammatical principles, modals, phrases & idioms, affixes, sentence structures, why & yes/no questions, conditional sentences. Vocabulary (12%): GRE,Technical& scientific vocabulary, defining terms. Writing –5+7+4+4=20% (a)Technical Writing-12% (i) Paragraph writing. Interpreting from table /data/ wagon wheel / graph /figure (At least 150 words)-5% (ii) Opinion based essaywritings (At least 250 words)-7% (b) Others-4%+4 %=8% (i)Business letters, job application, memos, quotation, tender notice Reading (2 passages)-10%+10%=20% Reading approaches, Comprehension of technical & non-technical materials-skimming, scanning, inferring & responding to context Passages must be paragraph types with letter marks (A, B, C, D………..) Options:- Write correct letter in boxes from letter marks (A, B, C, D………..) passages which match with each sentence, Or, Matching with events from letter marks (A, B, C, D………..) passages

Or, List of headings Or, Statements agree with information (True/False/Not Given) Or, Fill up with appropriate word from the passages without list Or, Fill up with appropriate word from the passages with list (synonyms word) Or, multiple choice ENG 105 Technical English Lab. 1.0 Credits, 2 hours/week Lab-60%; Quizzes-30%; 10% attendances Spoken English: 30% Introduction to phonetic symbols, dialogue, responding to particular situations, extempore speech, and cue card on situational condition/himself/herself. Listening-30% Fill the gap, multiple choice, etc. from CD recorder PHY 114 Physics I (Waves and Oscillations, Optics and Thermal Physics) 3 Credits; 3hours/week Waves and Oscillations: Simple harmonic motion, Differential equation of simple harmonic oscillator, total energy and average energy, combination of simple harmonic oscillations, spring mass system, torsional pendulum; two body oscillation, reduced mass, damped oscillation, forced oscillation, resonance, vibrations of membranes and columns, progressive wave, power and intensity of wave, stationary wave, energy calculation of progressive and stationary wave, group and phase velocities, sound waves-Doppler Effect, Sabine’s formula, architectord acoustics. Optics: Defects of images: Spherical aberration, astigmatism, coma, distortion, curvature, chromatic aberration, theories of light, Haygen’s principle; Interference of light: Young’s double slit experiment, displacement of fringes and its uses, Fresnel bi-prism, interference in thin film, Newton’s rings, interferometers; Diffraction: Diffraction by single slit, diffraction from a circular aperture, resolving power of optical instruments, diffraction at double slit and N-slits, diffraction grating; Polarization: production and analysis of polarized light, Brewster’s law, Malus law, polarization by double refraction, Nicol prism, optical activity, polarimeters, optics of crystal optical effect in crystal, laser, nonlinear optics. Thermal Physics: Heat and work, Zeroth law of thermodynamics, thermometer, thermocouple, the first law of thermodynamics and its applications; Kinetic theory of gases- kinetic interpretation of temperature, specific heats of ideal gases, equipartition of energy, mean free path, work done by gas, isothermal and adiabatic relations, vandarwaal’s equation of state, Maxwell’s distribution of molecular speeds, reversible and irreversible processes, Carnot’s cycle, second law thermodynamics, Carnot’s theorem, entropy, thermodynamic functions, Maxwell relations, Clausius and Clapeyron equation. PHY 115 Physics I Lab. 0.75.0 Credits; 3/2 hours/week Laboratory experiments based on theory and concepts learnt in PHY 114. CE 125 Engineering Drawing 1.0 Credits, 2 hours/week Introduction: lettering, numbering and heading; Instrument and their use; sectional views and isometric views of solid geometrical figures. Plan, elevation and section of multistoried building; building services drawings; detailed drawing of lattice towers. Viva Voce Central viva based on EEE 101, PHY 115, CE 125 and ENG 105

Year-1 Semester-2 EEE 150 Electrical Circuits II Prerequisite EEE 100 3 Credits, 3 hours/week Analysis of Single Phase AC Circuits: Series and parallel RL, RC and RLC circuits, Resonance in AC circuits, application of network theorems in AC circuits. Circuits with non-sinusoidal excitations, transients in AC circuits, Analysis of Poly Phase Circuits: Poly phase supply, 3-phase conditions, balanced and unbalanced circuits, power calculation. Magnetically couple circuits: Self and mutual inductances, coupling co-efficient, reflected impedance, transfer impedance. Two Port Networks (TPN): Two port networks (symmetrical & asymmetrical),determination of two port parameters, relationship between two port parameters, iterative impedance, image impedance, characteristic impedance, image propagation function, reflection of voltage, current and power; insertion loss. Filter: Passivefilters, impedance matching of filters, Butterworth and Chebychev filters. Book Recommended: 1. Alternating-Current Circuits - R.M. Kerchne, G.F. Corcoran 2. Introductory Circuit Analysis – Robert L.Boylestad 3. Fundamentals of Electric Circuits- C. K. Alexander M. N. O.Sadiku, 4. Linear Electric Circuits-W.L.Cassell EEE 151 Electrical Circuits II Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 150. MAT 154 Engineering Mathematics III (Ordinary & Partial Differential Equations) 3 Credits, 3 hours/week Ordinary Differential Equations: Degree and order of ordinary differential equations, formation of differential equations by various methods, solution of first order differential equations.Solution of general linear equations of second and higher orders with constant coefficients, applications.Solution of homogeneous linear equations of the higher order when the dependent or independent variables are absent.Solution of differential equations by the method based on the factorization of the operators.Frobeniousmethod. Legendre and Bessel’s function. Partial Differential Equations: Introduction.Linear and non-linear first order equations. Standard forms. Linear equations of higher order.Equations of the second order with variable coefficients.Wave equations.Particular solution with boundary and initial conditions. STA 156 Statistics for Engineers 3 Credits, 3 hours/week Statistics: Meaning & Scope, Variables and Attributes, Collection and presentation of Statistical data, Frequency Distribution and Graphical Representation. Analysis of Statistical Data: Location, Dispersion and their measures.Skewness, Kurtosis and their measures. Moment and cumulates, Regression and correlation

Elements of Probabilities: Concept of probability, Sample Space, Events.Union and Intersection of Events.Probability of Events.Laws of probability.Conditional Probabilities. Bays probability. Chebysec's Inequality. Random Variables and Probability Distribution: Basic concepts.Discrete and continuous Random variables.Density and distribution functions.Mathematical Expectation and variance.Conditional Expectation and conditional variance.Expected values and variances of the density distributions.Moments and Cumulant generating functions.Characteristicfunction.Study of Binomial, Poisson, Normal.Geometric, Multinomial, uniform, exponential, Gamma, distributions. Sampling Distributing: Study of 2Distribution, T-Distribution and F-Distribution, Properties, uses & Applications. Elements of Point Estimations: Basic Concepts. Consistent estimates. Unbiased estimates. Mean and variance of estimates.Principle of Maximum Likelihood. Illustration from Binomial, poission& Normal Distributions Decision Rules: Statistical decisions; Statistical hypothesis; Critical region, Best critical region; Two types of errors; procedure of Test of hypothesis; Most powerful test, standard Errors. Test of Significance: Est. of single mean & single variance. Comparison of two sample Means, proportions and Variances. Exact test for 2*2 tables. Test for r*c tables. Three-Way contingency tables. PHY 164 Physics II (Modern Physics, Nuclear Physics and Quantum Mechanics) 2 Credits, 2 hours /week Atomic Structure: Rutherford scattering, atomic structure (Bohr model, Thomson model, Rutherford model), Zeeman effect. Structure of Matter: Classification of solids, crystal structure of solids, Bragg’s law, distinction between metal, insulator and semiconductor. Modern Physics: Galilean relatively and Einstein’s special theory of relativity; Lorentz transformation equations, Length contraction, time dilation and mass-energy relation, photoelectric effect, Compton effect, De’Broglie matter waves. Nuclear Physics: Constituent of atomic nucleus, Nuclear binding energy, different types of radioactivity, radioactive decay law; Nuclear reactions, nuclear fission, nuclear fusion. Mechanics: Linear momentum of a particle, linear momentum of a system of particles, conservation of linear momentum, some applications of the momentum principle; Angular momentum of a particle, angular momentum of a system of particles, Kepler’s law of planetary motion, the law of Universal Gravitation, the motion of planets and satellites. Introductory Quantum Mechanics: Wave function, uncertainty principle, postulates, Schrödinger time independent equation, expectation value, probability, particle in a Zero potential, calculation of energy. AEC 184 Chemistry 3 Credits, 3 hours/week Atomic Structure, quantum numbers, Pauli’s exclusion principle, electronic configuration, periodic table, properties and uses of noble gases, different types of chemical bonds and their properties, molecular structures of compounds, selective organic reactions. Different types of solutions and their compositions. Phase rule, phase diagram of monocomponent system. Properties of dilute solutions.Thermochemistry, chemical kinetics, chemical equilibrium.Ionization of water and pH concept.Electrical properties of solution.

AEC 185 Chemistry Lab. 0.75 Credits, 3/2 hours/week Volumetric analysis: acid-base titration, oxidation-reduction titrations, determination of Fe, Cu and Ca volumetrically. CSE 194 Programming Language 3 credits, 3 hours/week Introduction to digital computers. Programming languages, algorithms and flow charts. Structured programming using C: Variables and constants, operators, expressions, control statements, functions, array, pointer, structure union, user defined data types, input-output files. Object oriented programming using C++: Introduction, classes and objects; polymorphism; function and operator overloading; inheritance. CSE 195 Programming Language Lab. 1.5 credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in CSE 194. Viva Voce Central viva based on EEE 151, CSE 195 and AEC 185

Year-2 Semester-1 EEE 201 Electrical Service Design 0.75 Credits, 3/2 hours/week Familiarization with electric switches: electrical fittings and fixtures. Wire wrapping; Soldering; Electrical symbols; Connection of tube light, staircase lighting, flickering lighting, moving lighting, simple traffic signals, calling bells, etc. Design of PCB layout: etching, trouble shooting, soldering &de-soldering. Wiring system design, drafting, estimation: Design for illumination and lighting. Electrical installation system design: substation, BBT and protection, air conditioning, heating and lifts. Design for intercom, public address systems, telephone system and LAN. Design of security system including CCTV, fire alarm, smoke detector, burglar alarm and sprinkler system.A design problem on a multi-stored building. EEE 210 Electronics I Prerequisite EEE 100 3 Credits, 3 hours/week P-N Junction as a Circuit Element: Intrinsic and extrinsic semiconductors, operational principle of p-n junction diode, contact potential, biasing of diode, current-voltage characteristics of a diode, simplified DC and AC diode models, dynamic resistance and capacitance. Diode Circuits: Half wave and full wave rectifiers, rectifiers with filter capacitor, characteristics of a Zener diode, Zener shunt regulator, clamping and clipping circuits. Bipolar Junction Transistor (BJT): Current components, BJT characteristics and regions of operation, BJT as an amplifier, biasing the BJT for discrete circuits, small signal equivalent circuit models, BJT as a switch. BJT Amplifier Circuits: Voltage and current gain, input output impedance of common base, common emitter and common collector amplifier circuits, multistage amplifiers.

Metal Oxide Semiconductor Field Effect Transistor (MOSFET): Structure and physical operation of an enhancement MOSFET, threshold voltage, body effect, current-voltage characteristics of an enhancement MOSFET, biasing discrete and integrated amplifier circuits, single–stage MOS amplifiers, MOSFET as a switch, introduction to VMOS and CMOS inverter. Differential and multistage amplifiers, small-signal operation, differential and common mode gains Junction Field-Effect-Transistor (JFET): Structure and physical operation of JFET, transistor characteristics, pinch-off voltage. Book Recommended: 1. Microelectronic circuits- A.S. Sedra ,K.C. Smith 2. Electronic Principles - Albert Malvino

3. Electronic Devices and Circuit Theory - Robert L. Boylestad, Louis Nashelsky 4. Principles of Electronics-V.K Mehta, Rohit Mehta 5. Basic Electronics: Solid State-B.L. Theraja

EEE 211 Electronics I Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 210. EEE 220 Electrical Machine I Prerequisite EEE 100 3 credits, 3 hours/week DC Generator: Types, no-load voltage characteristics, buildup of a self-excited shunt generator, critical field resistance, load-voltage characteristic, effect of speed on no-load and load characteristics and voltage regulation.Armature reaction, losses and efficiency, Parallel operation of DC generators. DC Motor: Torque, counter emf, speed, torque-speed characteristics, starting and speed regulation. Speed control by converter and chopper, Crane, traction and hoist application of DC motor, Choice of DC motors for different applications. Transformer: Ideal transformer- transformation ratio, no-load and load vector diagrams; actual transformer- equivalent circuit, regulation, short circuit and open circuit tests. Three phase transformer and its V-connection, Scott connections, three phase operation of single-phase transformer; Vector group of three phase transformers. Determination of transformer constants and polarity, Harmonics in polyphase transformers, Induction voltage regulators; Autotransformers: three phase and single phase, Power transformers: bushing, Cooling, Tap Changing and parallel operation Book Recommended:

1. Electric Machines - C.I. Hubert 2. Direct and Alternating Current Machinery - Rosenblatt, Friedman 3. Electrical Machines – S K Bhattacharya 4. A text book of Electrical Technology(Vol. II)-B.L. Theraja, A.kThereja

EEE 221 Electrical Machine I Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 220. ME 204 Mechanical Engineering Fundamentals 3 Credits, 3 hours/week Introduction to Sources of Energy: Steam generating units with accessories and mountings; steam turbines, condensers, vapor cycles. Internal Combustion Engine: Introduction to internal combustion engines & their cycles, gas turbines.

Refrigeration and Air Conditioning: Applications; refrigerants, different refrigeration methods. Fluid Machinery: Fluid flow, measurements of flow, friction in flow, centrifugal pumps, fans, blowers & compressors. Fundamental of Conduction, Convection and Radiation: One dimensional steady state conduction in plated pipes; Critical thickness of insulation. ME 205 Mechanical Engineering Fundamentals Lab. 0.75 Credits, 3/2 hours/week Laboratory experiments based on theory and concepts learnt in ME 204. MAT 204 Engineering Mathematics IV (Complex Variable, & Vector Analysis) 3 Credits, 3 hours/week Complex Variable: Complex number system. General functions of a complex variable. Limits and continuity of a function of complex variable and related theorems.Complex differentiation and the Cauchy-Riemann equations. Mapping by elementary functions. Infinite series.Convergence and uniform convergence. Line integral of a complex function. Cauchy’s integral formula.Liouville’stheorem.Taylor’s and Laurent’s theorem.Singularpoints.Residue, Cauchy’s residue theorem.Contour integration, conformal mapping. Vector Analysis: Scalars and vectors, equality of vectors, addition and subtraction of vectors, geometrical interpretation. Multiple product of vectors. Linear dependence and independence of vectors.Differentiation and Integration of vectors together with elementary applications.Line, Surface and volume integrals. Gradient of a scalar functions, divergence and curl of a vector function, various formulae. Integrals form of gradient, divergence and curl. Divergence theorem, Stoke’s theorem, Green’s theorem and Gauss’s theorem AIS 214 Industrial Management and Accountancy 2.0 Credits, 2 hours/week Industry: Types of Industry, Commerce – Hindrance removed by Commerce, Business Environment. Sole Proprietorships: Features, Advantages, Disadvantages of Sole Proprietorship, Sustainability of Sole proprietorships. Partnership: Features, Advantages, Disadvantages, the Partnership Contract. Joint Stock Company: Characteristics, Advantages, Disadvantages, Types, Comparison between Public and Private Ltd Company and Formation of company. Fundamentals of Management: What is management? Management Function, Levels of Management, Management roles, Core Management skills, Principles of Management. Organizing the Business: Formal and Informal Organization, Centralization and Decentralization, Principles of Organizing, Functional Structure, Product Structure, Terrestrial Structure, Matrix Structure, Multiple Structure. Accountings: History, Scope and Nature of Accounting, Information and Uses Transaction: Meaning and Features, Double entry System, Characteristics, Account – Meaning, Classification, Rules for Determining Debit and Credit, Accounting.Equation, Accounting cycle. Journal: Meaning, Features, Necessity, Types, Practical Problems. Ledger: Definition, Advantages, Classification, Rules, Practical Problems. Cash book: Features, Advantages, Double and Triple Column Cash Book, Discount.

Trial Balance: Meaning, Characteristics, Objects, Practical problems, Income Tax: Practices, Income Tax Law. Preparation of Financial Statements. Viva Voce Central viva based on EEE 201, EEE 211, EEE 221 and ME 205

Year-2 Semester-2 EEE 250 Measurement and Instrumentation Prerequisite EEE 210, 3 Credits, 3 hours/week Introduction: Applications, functional elements of a measurement system and classification of instruments (Ammeter, Voltmeter, wattmeter, AVO meter, Energy meter, Ampere-hour meter, CRO). Measurement of Electrical Quantities: Current and voltage, power and energy measurement.Current and voltage, power and energy measurement Current and potential transformer. Transducers: Mechanical, electrical and optical transducers. Measurement of Non-Electrical Quantities: Temperature, pressure, flow, level, strain, force and torque, earthquake, speed, frequency, phase difference. Basic Elements of DC and AC Signal Conditioning: Instrumentation amplifier, noise and source of noise, noise elimination compensation, function generation and linearization, A/D and D/A converters, sample and hold circuits. Data Transmission and Telemetry: Methods of data transmission, DC/AC telemetry system and digital data transmission.Recording and display devices.Data acquisition system and microprocessor applications in instrumentation. Books recommended: 1. Measurement & Instrumentation – A. K. Sawhney 2. Measurement & Instrumentation – Harries K. Forrest EEE 251 Measurement and Instrumentation Lab. 0.75 Credits, 3/2 hours/week Laboratory experiments based on theory and concepts learnt in EEE 250. EEE-253 Electrical & Electronic Circuit Simulation Lab 1.5 Credits, 3 hours/week Simulation laboratory based on EEE 100, EEE 150, EEE 210 and EEE260 theory courses. Students will verify the theories and concepts learned in on EEE 100, EEE 150, EEE 210 and EEE260 using simulation software like PSpice and MATLAB. Students will also perform specific design of electrical (DC and AC) and electronic circuits theoretically and by simulation. EEE 260 Electronics II Prerequisite EEE 210 3 Credits, 3 hours/week Frequency Response of Amplifiers: Poles, Zeros and Bode plots, amplifier transfer function, techniques of determining 3 dB frequencies of amplifier circuits, frequency response of single-stage and cascade amplifiers, frequency response of differential amplifiers.

Operational Amplifiers (Op-Amp): Properties of ideal OP-Amps, non-inverting and inverting amplifiers, integrators, differentiator, weighted summer and other applications of Op-Amp circuits, Schmitt trigger, comparator, Differential and Common gain, effects of finite open loop gain and bandwidth on circuit performance, logic operation of Op-Amp, DC imperfections. DC analysis, small-signal analysis of different stages, gain and frequency response of 741 OP-Amp Feedback Amplifier: Properties, feedback amplifiers with different topologies, stability, frequency compensation. Active Filters: Different types of filters and specifications, transfer functions, realization of first and second order low, high and band pass filters using OP-Amps. Oscillators and Timing Circuits: Sinusoidal oscillators, Phase shift oscillator, resonant circuit oscillator, general form of oscillator circuit, crystal oscillators. Multi-vibrators, IC 555 and its applications.VCO, PLL and blocking oscillator. Power Amplifiers: Classification of output stages, Class A, B and AB output stage, Class C and Class D. push-pull Class B and C amplifiers and their design Heat sink. Book Recommended:

1. Operational Amplifiers and Linear IntegratedCircuits- R.F. Coughlin, F.F. Driscoll 2. Integrated Electronics – Analog and Digital Circuits and Systems - Jacob Millman,

Christos C. Halkias 3. Electronic Devices and Circuit Theory - Robert L. Boylestad, Louis Nashelsky 4. Op-Amps and Linear Integrated Circuits-Ramakant A. Gayakwad

EEE 261 Electronics II Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 261. EEE 270 Electrical Machine II Prerequisite EEE 220 3 credits, 3 hours/week Three Phase Induction Motor: Rotating magnetic field, equivalent circuit, vector diagram, torque-speed characteristics, effect of changing rotor resistance and reactance on torque-speed curves, motor torque and developed rotor power, no-load test, blocked rotor test, starting and braking and speed control. Single Phase Induction Motor: Theory of operation, equivalent circuit and starting. Synchronous Generator: Windings, excitation systems, equivalent circuit, vector diagrams at different loads, factors affecting voltage regulation, synchronous impedance, synchronous impedance methods of predicting voltage regulation and its limitations. Parallel operation: necessary conditions, synchronizing, circulating current and vector diagram. Synchronous Motor: Operation, effect of loading under different excitation condition, effect of changing excitation, V-curves and starting. Special types motor: Universal motor, Stepper motor, permanent magnet motor, Hysteresis motor and Reluctancemotor. Book Recommended:

1. Electric Machinery Fundamentals- S.J. Chapman. 2. Alternating Current Machines- A. F. PuchsteinT. C. Lloyd, A. G. Conard 3. A Textbook of Electrical Technology - AC and DC Machines- B. L. Theraja, A. K. Theraja

EEE 271 Electrical Machine II Lab 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 270. EEE 280 Electromagnetics Prerequisite: MAT 106, MAT 156 3 Credits, 3 hours/week Review of Vector Analysis: Coordinate Systems, Vector algebra, gradient, divergence and curl. Static Electric Field: Postulates of electrostatics, Coulomb’s law for discrete and continuously distributed charges, force, field intensity, flux density, Gauss’s law and its applications, electric potential due to charge distribution, conductors and dielectrics in static electric field, boundary conditions; capacitance- electrostatic energy and forces, energy in terms of field equations, capacitance calculations of different geometries; boundary value problems- Poisson’s and Laplace’s equations in different co-ordinate systems, method of images, graphical field mapping. Static Magnetic Field: Postulates of magneto statics, Biot-Savart’s law, Ampere’s law and applications, vector magnetic potential, magnetic dipole, magnetization, magnetic field intensity, permeability, boundary conditions for magnetic field, magnetic energy, magnetic forces, torque and inductance of different geometries. Time Varying Fields and Maxwell’s Equations: Faradays law of electromagnetic induction, Maxwell’s equations- differential and integral forms, boundary conditions, potential functions; time harmonic fields and Poynting theorem, depth of penetration, internal impedance, and power loss. Plane Electromagnetic Wave: Plane wave in lossless media- Doppler effect, transverse electromagnetic wave, Polarization of plane wave; plane wave in lossy media- low loss dielectrics, good conductors; transmission line analogy- reflection coefficient, transmission coefficient, characteristics impedance, standing wave ratio, group velocity, instantaneous and average power densities, normal and oblique incidence of plane waves at plane boundaries for different polarization. Book Recommended:

1. Fundamentals of Engineering Electromagnetics- D.K. Cheng 2. Fields and wave in communication electronics- S.RamoJ.R. Whinnery,T. Van Duzer 3. Electromagnetics for Engineers- F. T. Ulaby 4. Elements of Electromagnetics- Matthew N. O. Sadiku 5. Introduction to electromagnetic fields-Clayton R. Paul, S. A. Nasar

MAT 254 Engineering Mathematics V (Fourier Analysis & Laplace Transformation) 3 Credits, 3 hours/week Fourier analysis: Real and complex forms. Finite Fourier transforms. Fourier integral. Fourier transforms and their uses in solving boundary value problems. Laplace Transformation: Definition, Laplace transforms of some elementary functions. Sufficient conditions for existence of Laplace transforms. Inverse Laplace transforms. Laplace transforms of derivatives. Some special theorems on Laplace transforms. Partial fraction. Solution of differential equations by Laplace transforms. Evaluation of improper integrals. Viva Voce Central viva based on EEE 251, EEE 253, EEE 261 and EEE 271

Year-3 Semester-1 EEE 300 Signals and Linear Systems Prerequisite EEE101, MAT 254 3 Credits, 3 hours/week Classification of Signal and Systems: Signals- classification, basic operation on signals, elementary signals, representation of signal using impulse function; systems- classification. Properties of Linear Time Invariant (LTI) Systems: Linearity, causality, time invariance, memory, stability, invertibility. Time Domain Analysis of LTI Systems: Differential equations- system representation, order of the system, solution techniques, zero state and zero input response, System properties: impulse response – convolution integral, determination of system properties; state variable- basic concept, static equation and time domain solution. Frequency Domain Analysis of LTI Systems: Fourier series- properties, harmonic representation, system response, frequency response of LTI systems; Fourier transformation- properties, system transfer function, system response and distortion less systems. Applications of Time and Frequency Domain Analysis: Solution of analog electrical and mechanical systems, amplitude modulation and demodulation, time-division and frequency-division multiplexing. Laplace Transformation: Properties, inverse transform, solution of system equations, system transfer function, system stability and frequency response and application. Analogous Systems: Electrical, mechanical and electro-mechanical systems. Book Recommended:

1. Continuous and Discrete Signals and Systems- S.S.Soliman, M.D. Srinath 2. Signal Processing and Linear Systems- B.P. Lathi 3. Analysis of Linear Systems- David K. Cheng 4. Signals and Systems- Simon Haykin, Barry Van Veen 5. Linear Circuit Analysis:Time Domain, Phasor, and Laplace Transform Approaches-

Raymond A. DeCarlo , Pen-Min Lin EEE 308 Project 0.75 Credits, 3/2 hours/week The students are required to undertake a projectin the field of Electrical and Electronic Engineering which would be a design work. The objective is to provide an opportunity to the students to develop initiative, creative ability, confidence and engineering judgment. EEE 310 Digital Electronics Prerequisite: EEE 210 3 Credits, 3 hours/week Analysis and Synthesis of Digital Logic Circuits: Number system and codes.Boolean algebra, De Morgan’s law, logic gates and truth tables, combinational logic design, minimization techniques, implementation of basic static logic gates in CMOS and BiCMOS. Arithmetic and data handling logic circuits, decoders and encoders, multiplexers and combinational circuit design. Programmable Logic Devices: Logic arrays, Field Programmable Logic Arrays and Programmable Read Only Memory. Sequential Circuits: Different types of latches, flip-flops and their design using ASM approach, timing analysis, timing analysis and power optimization of sequential circuits.Modular sequential logic circuit design: Shift registers, counters and their applications.

Books recommended: 1. Modern Digital Electronics – R. P. Jain 2. Digital Systems: Principles and Applications- Ronald J. Tocci 3. Digital Logic and Computer Design- M. Morris Mano, 4. Digital Logic Circuit Analysis and Design- Victor P.NelsonH. Troy Nagle, Bill D. Carroll, J. David Irwin EEE 311 Digital Electronics Lab. 1.5 credits, 3hours/week Laboratory experiments based on theory and concepts learnt in EEE 310. Design of simple systems using the principles learned in EEE 310. EEE 320 Power Electronics Prerequisite EEE 210 3 Credits, 3 hours/week Power semiconductor switches and triggering devices: BJT, MOSFET, SCR, IGBT, GTO, TRIAC, UJT and DIAC. Rectifiers: Uncontrolled and controlled single phase and three phase. Regulated power supplies: Linear-series and shunt, switching buck, buck boost, boost and cuk regulators. AC voltage controllers, single and three phase. Choppers.DC motor control.Single phase cyclo-converter. Inverters: Single phase and three phase current and voltage source. AC motor control.Stepper motor control.Resonance inverters. Pulse width modulation control of static converters. Books Recommended:

1. Power Electronics, circuits, devices and applications- Muhammed H. Rashid 2. Introduction to Power Electronic- Daniel W. Hart

EEE 321 Power Electronic Lab 1.5Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 320. Design of simple systems using the principles learned in EEE 320. EEE 340 Numerical Methods for Engineering Prerequisite CSE 194 3.0 Credits, 3 hours/week Introduction: Motivation and errors in numerical techniques, Taylor series. Finite Difference Calculus: Forward, backward, divided, and central difference and difference of a polynomial. Interpolation and Extrapolation: Newton’s formula, lagrange, spline, chebyshev and inverse; extrapolation. Nonlinear Equations: Iteration, bisection, false position, Raphson, Secant and Muller’s methods. Simultaneous Linear Algebraic Equations: Cramer’s rule, inversion of matrices, Gauss elimination, Gauss-Jordon method, factorization and Gauss-Siedel iteration methods. Curve Fitting: Linear and polynomial regression, fitting power, exponential and trigonometric functions,

Ordinary differential equations: initial value problem, Taylor’s series method, Picard’s method of successive approximation, Euler’s method and Runge-Kutta method. Boundary value problems. Numerical Integration: General quadrature formula, trapezoidal rule and Simpson’s rule; numerical differentiation. Book recommended:

1. Numerical Methods for Engineers – Steven C. Chapra, Raymond P. Canale 2. Computer Applications for Numerical Methods- S SKuo 3. Introductory Methods of Numerical Analysis- S SSastry 4. Numerical Analysis-A. R. Vasishtha, vipinVasishtha, 5. Numerical Methods using Matlab- John H. Mathews, Kurtis D. Fink

EEE 341 Numerical Methods for Engineering Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 340. SOC 304 Sociology and Professional Ethics 2 Credits, 2 hours/week Sociology: Scope.Some basic concepts.Social evolution and techniques of production, culture and civilization.Social structure of Bangladesh.Population and world resources.Oriental and Occidental societies, Industrial revolution. Family-urbanization and industrialization. Co-operative and Socialist movements. Professional Ethics: History and Development of Engineering Ethics: Study of Ethics in Engineering. Applied Ethics in engineering.Human qualities of an engineer.Obligation of an engineer to the clients and to other engineers.Measures to be taken in order to improve the quality of engineering profession. Ethical Expectations: Employers and Employees inter-professional relationship, maintaining a commitment of Ethical standards.Desired characteristics of a professional code.Institutionalization of Ethical conduct cyber law moral thoughts. ECO 306 Economics 2 Credits, 2 hours/week Introduction: Definition of Economics.Economics and Engineering. Micro-Economics: The theory of demand and supply and their elasticities.Pricedetermination.Nature of an economic theory, applicability of economic theories to the problems of developing countries.Indifference curve technique.Marginal analysis. Production, production function, types of productivity. Rational region of production of an engineering firm. Concepts of market and market structure. Cost analysis and cost function. Small scale production and large scale production.Optimization.Theory of distribution. Macro-Economics: Savings, investment, employment, National income analysis.Inflation.Monetary policy, fiscal policy and trade policy with reference to Bangladesh.Economics of development and planning. Viva Voce Central viva based on EEE 308, EEE 311, EEE 321 and EEE 341

Year-3 Semester-2 EEE 362 Electronic Circuit for Communication System 2 Credits, 2 hours/week Radio communications: Properties and propagation of radio waves. Radio Receivers: Receiver types, TRF and super heterodyne receivers, AM & FM Receiver. Television: Introduction, principle of operation, transmitter and receiver and their circuits. Receiving and transmitting antenna. Camera tube, Picture tube, Electron beam scanning, T-lines, balum, duplexer, vestigial side-band filters and their circuits. Introduction to color TV, VCD, DVD, CCTV, CATV, MATV, TV Booster. Radar: Introduction, radar-equation, Pulse and MTI Radar, CW and FM Radar: Delay lines and cancellers, range getting. Introduction to Telephony system. Book recommended:

1. Television Fundamentals – Fowler and Liport 2. Basic TV-B.Grob 3. Radio & TV engineering-A.G Mihal 4. Digital Television Systems –Marcelo S. Alencer 5. Radio Receiver Design- K.R Sturlen 6. Telecommunication switching systems and networks-ThiagarajanViswanathan

*EEE 368 Industrial Training: 0.75 Credits For 2 Weeks Students will be attached with the industries/service agencies for two weeks after completing their Third year second semester (before starting Fourth year) to gain practical knowledge. Without satisfactory completion of this course the student will not fulfill the requirements of B. Sc. Engineering Degree EEE 380 Communication Theory 4 Credits, 4 hours/week Overview of Communication Systems: Basic principles, fundamental elements, system limitations, message source, bandwidth requirements, transmission media types, bandwidth and transmission capacity. Noise: Source, characteristics of various types of noise and S/N ratio. Information Theory: Measure of information, source encoding, error free communication over a noisy channel, channel capacity of a continuous system and channel capacity of a discrete memory less system, communication entropy, data compression. Communication Systems: Analog and digital communication, carrier, baseband, band pass and broadband communication; broadcast- and point to point- mode of communication. Continuous Wave Modulation: AM- DSB, SSB, VSB, QAM, spectral analysis of each type, envelope and synchronous detection; angle modulation- instantaneous frequency, FM, PM, spectral analysis, demodulation of FM and PM. Pulse Modulation: Sampling- sampling theorem, Nyquist criterion, aliasing, instantaneous and natural sampling; PAM principle, bandwidth requirements; PCM- quantization principle, quantization noise, non-uniform quantization, signal to quantization error ratio, demodulation of PCM, DPCM and DM principle, adaptive DM; line coding formats and bandwidths.

Digital Modulation: ASK principle, bandwidth requirements, detection, noise performance; PSK principle, bandwidth requirements, detection, DPSK, QPSK- noise performance, FSK- principle, continuous and discontinuous phase FSK, detection of FSK, MSK- bandwidth requirements. Concept of Multiplexing: TDMA, FDMA and CDMA Communication Systems Design: Design parameters, channel selection criteria and performance simulation Brief Introduction to Some Communication Systems: Mobile cellular communication system, Fiber optic communication system, Microwave communication system &Satellite communication. Books Recommended:

1. Modern Digital and Analog Communication System- B.P. Lathi 2. Communication Systems- Simon Haykin

EEE 381 Communication Theory Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 380. Design of simple systems using the principles learned in EEE 380. EEE 382 Control System 3 credits, 3 hours/week Introduction to Control Systems: Linear system models- transfer function, block diagram and signal flow graph (SFG). State Variables: SFG to state variables, transfer function to state variable and state variable to transfer function. Feedback Control System: Closed loop systems, parameter sensitivity, transient characteristics of control systems, effect of additional pole and zero on the system response and system types and steady state error. Routh stability criterion. Analysis of Feedback Control System: Root locus method and frequency response method. Design of Feedback Control System: Controllability and observability, root locus, frequency response and state variable methods. Digital Control Systems: Introduction, sampled data systems, stability analysis in Z-domain. Books Recommended: 1. Modern Control Engineering- Katsuhiko Ogata 2. Modern Control Systems- R.C. Dorf, R.H. Bishop 3. Control System Engineering- N.S. Nise 4. Automatic ControlSystems–B. C.Kuo EEE 383 Control System Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 382.

EEE 390 Microprocessor, Interfacing and System design Prerequisite EEE 301 3 Credits, 3 hours/week Fundamental Concepts: Microprocessor: A programmable device; microcomputer components and support ICs, building blocks of MPU based systems, microprocessor buses, programming principles using MASM, microprocessor instructions. 16-bit Architecture: Pin diagram and functions, memory organization, bus activities, register layout, internal processing blocks. Instruction Set: Classifications of instructions, addressing modes, address computing chart. I/O Controller Programming: Port definition and read/write instructions, parallel I/O programming using 8255, serial I/O programming using 8251, display programming using 8279 and LCD, keyboard programming using 8279 and discrete components, generation of timing functions using 8253 PIT controller. Interrupt Structure: Interrupt terminologies, hardware and software interrupt, multiple interrupt management. Data Conversion Algorithm: Number system and BCD arithmetic, BCD2BIN conversion, BIN2BCD conversion, binary multiplication, binary division. System Design (8086 based digital weighing machine: DWM) Top down/Bottom up design concept, hardware block diagram, control program flow chart, weight/rate acquisition and processing and display, cost computation and processing and display. Advanced Microprocessors and Microcontrollers: History of the evolution of MPU/MCU, multitasking systems, PVAM operation of Intel high performance architecture, overview of 80286 architecture, instruction and programming; overview of 80386 architecture, instruction and programming; overview of CISC and RISC microcontrollers, instruction and programming. Books Recommended:

1. Assembly Language Programming and Organization of the IBM PC- Y. Yu C. Marut 2. Microprocessor and Interfacing- D.V. Hall 3. Microprocessors and Microcomputer Based System Design- Mohamed Rafiquzzaman 4. Intel Microprocessors- Barry B. Brey

EEE 391 Microprocessor, Interfacing and System design Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 390. Design of simple systems using the principles learned in EEE 390. EEE 392 Power System I 3 Credits, 3 hours/week Line representation: equivalent circuit of short, medium and long line: T and π representation, exact solutions, equivalent circuit of long transmission line.Underground and overhead lines. Mechanical characteristics of transmission line: Sag and stress analysis, effect of wind and ice loading, supports at different elevation, conditions of erection, and effects of temperature changes. Network representation: Single line and reactance diagram of power system and per unit representation.

Fault analysis: Symmetrical fault calculation, symmetrical components, and sequence impedance and sequence networks, different unsymmetrical fault calculation Load flow studies: Gauss – Seidel method. Control of voltage, real power and reactive power.Reactive power compensation. Voltage control in transmission line: Tap changing transformers, Voltage regulator, booster transformers, induction regulator, shunt capacitor Power factor control in transmission line: Static condenser, Ferranti effect, synchronous condenser. Recent trends in transmission system: Overview of flexible ac transmission system (FACTS), high voltage dc transmission system (HVDC) and SCADA.Power system harmonics. Books Recommended:

1. Elements of Power SystemAnalyis –William D.Stevenson, Jr. 2. Electrical Power Systems- Ashfaq Hossain 3. Principle of Power Systems- V.K. Mehta, Rohit Mehta 4. Electrical Power Generation, Transmission and Distribution-S.N. Singh EEE 393 Power System I Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 392. Viva Voce Central viva based on EEE 368, EEE 381, EEE 383, EEE 391 and EEE 393

Year-4 Semester-1 EEE 408 Project and Thesis 1.0 Credits, 2 hours/week The students are required to undertake a projectin the field of Electrical and Electronic Engineering. The objective is to provide an opportunity to the students to develop initiative, creative ability, confidence and engineering judgment. The results of the work should be submitted in the form of a dissertation, which should include appropriate drawings, charts, tables, references etc. EEE 400 Digital Signal Processing Prerequisite MAT 204, MAT 254 3 credits, 3 hours/week Introduction to Digital Signal Processing (DSP): Discrete-time signals and systems, analog to digital conversion, impulse response, finite impulse response (FIR) and infinite impulse response (IIR) of discrete time systems, difference equation, convolution, transient and steady state response. Discrete Transformations: Discrete Fourier series, discrete-time Fourier series, discrete Fourier transform (DFT) and properties, fast Fourier transform (FFT), inverse fast Fourier transform, Z-transformation- properties, transfer function, poles and zeroes and inverse Z-transform. Correlation: Circular convolution, auto correlation and cross correlation. Digital Filters: FIR filters- linear phase filters, specifications, design using window, optimal and frequency sampling methods; IIR filters- specifications, design using impulse variant, bi-linear z-transformation, least square methods and finite precision effects.

Books Recommended: 1. Discrete-Time Signal Processing- A.V. Oppenheim, R.W. Schafer, J.R. Buck 2. Discrete Signal Processing – Principle, Algorithms and Applications- John G. Proakis,

Dimitris G. Manolakis 3. Digital Signal Processing – A Computer Based Approach-S. K. Mitra

EEE 401 Digital Signal Processing I Lab. 1.5 credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 400. Design of simple systems using the principles learned in EEE 400. EEE 402 Power System protection 3 credits, 3 hours/week Purpose of power system protection,Criteria for detecting faults: over current, differential current, difference of phase angles, over and under voltages, power direction, symmetrical components of current and voltages, impedance, frequency and temperature. Electromechanical, electronic and digital relays: Basic modules, over current, differential, distance and directional. Trip circuits. Different protection schemes for generator, transformer, motor, bus bar, transmission lines. Protection of ring mains and radial feeders.Miniature circuit breakers and fuses. Fuse: Commercially available fuses, their constructions, characteristics and applications. Circuit breakers: Principle of arc extinction, selection criteria and ratings of circuit breakers, types-air, oil, SF6, vacuum, ABCB, ACB, MCCB. Books Recommended:

1. Switchgear Protection and Power Systems- Sunil S. Rao 2. Power System Operation and Control-B.Wollenberg, A. Wood

EEE 403 Power System protection Lab 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 402. EEE 412 Electrical Properties of Materials Prerequisite PHY 164 3 Credits, 3 hours/week Atoms and Aggregates of Atoms: Bohr atomic model, shell model. Bonding and Types of Solids: Primary bonding, secondary bonding, mixed bonding. Crystal Structures: Types of crystals, lattice and basis, Bravais lattice and Miller indices. Classical Theory of Electrical and Thermal Conduction: Scattering, mobility and resistivity, temperature dependence of metal resistivity, Mathiessen’s rule, Hall Effect and thermal conductivity. Modern Theory of Metals: Determination of Fermi energy and average energy of electrons, classical and quantum mechanical calculation of specific heat.

Dielectric Properties of Materials: Polar and nonpolar dielectrics, dielectric constant, polarization- electronic, ionic and orientational; internal field, Clausius-Mosotti equation, spontaneous polarization, frequency dependency of dielectric constant, dielectric loss, piezoelectricity, Ferro electricity. Magnetic Properties of Materials: Magnetic moment, magnetization and relative permeability, different types of magnetic materials, origin of ferromagnetism and magnetic domains, coercive force, polycrystalline and permanent magnetic materials, introduction to superconductivity: Zero resistance and Meissner effect, Type I and Type II superconductors and critical current density. Band Theory of Solids: Band theory from molecular orbital, Bloch theorem, Kronig-Penny model, effective mass, density of states. Quantum Mechanics: Wave nature of electrons, Schrödinger’s equation, one dimensional quantum problems- infinite quantum well, potential step and potential barrier; Heisenberg’s uncertainty principle and quantum box. Carrier Statistics: Maxwell-Boltzmann and Fermi-Dirac distributions, Fermi energy. Books Recommended:

1. Principles of Electronic Materials and Devices- S.O. Kasap 2. Electrical Engineering Material-A. J. Dekkar

Viva Voce Central viva based on EEE 408, EEE 401, EEE 403 and Elective I Lab

Year-4 Semester-2 EEE 458 Project and Thesis 3 Credits, 6 hours/week The students are required to undertake a project in the field of Electrical and Electronic Engineering. The objective is to provide an opportunity to the students to develop initiative, creative ability, confidence and engineering judgment. The results of the work should be submitted in the form of a dissertation, which should include appropriate drawings, charts, tables, references etc. EEE 492 Microcontroller and PLC based System Design Prerequisite EEE 390 3 Credits, 3 hours/week Review of 8 bit/ 16 bit CISC/RISC microcontrollers: Hardwire architecture, First access register file, instruction pipelining. System design: Digital taximeter, prepaid energy meter, VVVF driven and the like, advances in system design. PLC Introduction to Programmable Logic Controllers (PLC), PLC Hardware, block diagram,Definitions of Allen-Bradley conditional inputs and outputs , logic and number systems, timers and counters,I/O configuration and downloading PLC programs,Programming Terminals and Peripherals, Relay Logic, Selection and connection of controlling devices, Development of P.L.C programs,Installation and troubleshooting sensors wired as sinking or sourcing current , P.L.C. applications. Books Recommended:

1. PIC Microcontrollers-An Embedded systems approach to Microcontrollers,3e- Bates 2. 8051 Microcontrollers: An Application Based Introduction- Calcutt 3. Programming the PIC Microcontrollers with Mbasic- Smith

EEE 493 Microcontroller and PLC based System Design Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 492. Design of simple systems using the principles learned in EEE 492 Viva Voce Central viva based on EEE 458, EEE 493, EEE 403, Elective III Lab and Elective IV Lab 4.0 Elective Courses offered by the Department of EEE 4.1 Power Group EEE 410 Power System II 3 Credits, 3 hours/week Inductance and Capacitance of overhead power line: Flux linkages, inductance due to external flux, inductance of single-phase two-wire line, composite conductor lines, G.M.D, 3-phase line with equilateral and with unsymmetrical spacing, parallel circuit of 3-phase line, and use of tables. Electric field, capacitance of two wire line, three-phase lines with symmetrical & with equilateral spacing, effect of earth Generalized line constants: General line equations in terms of ABCD constants, relations between constants, charts of line constants, constants of combined networks measurement of line constants. Insulators for overhead lines: Types of insulators, their constructions and performance, potential distribution in a string of insulators, string efficiency, methods by equalizing potential distribution, special types of insulators, testing of insulators. Insulated cables: Underground cables vs. overhead lines, insulating materials, electro static stress grading, three core cable-dielectric losses and heating, modern developments oil filled and gas filled cables, measurements of capacitance, cable testing, corona & corona power loss. Stability: Swing equation, power angle equation, equal area criterion, multi-machine system, step-by-step solution of swing equation, factors affecting transient stability. Power distribution: DC and AC distribution calculation for different network configuration, typical layout of a substation. Books Recommended:

1. Power System Analysis- J.J. Grainger, W.D. Stevenson 2. Power System Analysis–HadiSaadat 3. Electrical Power Generation, Transmission and Distribution- S.N. Singh 4. Principles of Power System- V.K. Mehta, Rohit Mehta

EEE 411 Power System IILab 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 410. EEE 430 High voltage engineering 3 Credits, 3 hours/week Ionization and decay process: Townsend’s first and second ionization coefficient. Electric breakdown in gases. Townsend’s criterion for spark breakdown. Sparking potential. Penning effect. Corona discharges, power loss calculation. Breakdown of solid and liquid, dielectrics. Generation of high voltage: Alternating voltage, transformer cascade. Impulse voltage generator and its mathematical analysis. Design consideration of impulse generators. Triggering of impulse generators. DC voltage doubler and cascade circuits. Electrostatic generator, voltage stabilization.

Measurement of High Voltage: Measurement of high ac, dc, and impulse voltages and currents. High Voltage Testing: destructive and non-destructive high voltage testing of electrical equipment, impulse testing. Transient overvoltage and insulation coordination, Test of dc and ac cable, Series resonant circuit for high voltage ac testing Electrostatic voltmeter, sphere gap. Potential divider. Oil testing. Design consideration of transmission line based on direct stroke. High voltage lightning arrester. EEE 460 Electrical Machine III 3 Credits, 3 hours/week Special Machines: Series universal motor, permanent magnet DC motor, unipolars and bipolar brush less DC motors, stepper motor and control circuits. Reluctance and hysteresis motors with drives circuits, switched reluctance motor, electro static motor, repulsion motor, synchronous and control transformers. Permanent magnet synchronous motors. Acyclic Machines: Generators, conduction pump and induction pump. Magneto Hydrodynamic Generators: Fuel cells, thermoelectric generators, flywheels, vector control, linear motors and traction. Photovoltaic Systems: Stand alone and grid interfaced. Wind Turbine Generators: Induction generator, AC-DC-AC conversion. EEE 461 Electrical Machine III Lab 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 460. EEE 470 Non-Conventional Energy 3 Credits, 3 hours/week Solar Geometry: Motion of the earth about the sun, Angle of declination, Solar time, Location of the sun relative to a horizontal plane. Solar Intensities: Solar spectrum and intensities above the atmosphere, Instrumentation for measuring solar intensities, solar intensities at earth level normal to the sun, Insolation on surfaces, Direct and Diffuse Radiation. Solar Heating & Storage Systems: Energy Flow and Efficiency of Flat-Plate collectors, Frames, Boxes, Insulation and Glazing, Absorber plates and Heat-transfer Fluids. Sensible heat storage, Phase-change storage and Other types of storages. Silicon Solar Cells: Principles, Efficiency and efficiency limiting factors. Design consideration, cell fabrication, Construction of Solar Modules & Panels. Other Cells and Materials: MIS Solar cells and other Device structures, Cell Materials. Other Nonconventional Sources of Energy: Biomass; Wind power; Water power & Tidal power. EEE 471 Non-Conventional Energy Lab 0.75 Credits, 3/2 hours/week Laboratory experiments based on theory and concepts learnt in EEE 470.

EEE 472 Power Plant Engineering and Economy 3 Credits, 3 hours/week Power Plants General layout and principles, steam turbine, gas turbine, combined cycle, hydro and nuclear. Plant performance and operation characteristics, Atomic power plant Nuclear fission and fusion; energy release; moderation, control, cooling and shielding aspects. Factor, place, utility and effects on environment and human beings. Selection of Location Technical, economical (Efficiency, heat rate and incremental rate, load division between generating units for economy, economic conductor selection, Kelvin’s law.) and environmental factors (forces on bus section in case of short circuit), load forecasting, load shearing (base load & peak load plant), Optimum load scheduling, transmission line loss ,chronological load curves to distribute load among units Graphical method for location of distribution systems.Bus system layout.Importance of current limiting reactors. Generation Scheduling Deterministic and probabilistic generation, load curves- demand factor, diversity factor, load duration curve, energy load curves, load factor, capacity factor, plant factor, electricity tariff formulation and type. 4.2 Electronics & Communication Group EEE 420 Microwave Engineering 3 Credits, 3 hours/week Transmission Lines: Voltage and current in ideal transmission lines, reflection, transmission, standing wave, impedance transformation, smith chart, impedance matching and lossy transmission lines. Waveguides: General formulation, modes of propagation and losses in parallel plate, rectangular and circular waveguides, and transit time effect, velocity modulation, space charge wave. Microstrips: Structure and characteristics. Rectangular Resonant Cavities: Energy storage, losses and Q. Radiation: Small current element, radiation resistance, radiation pattern and properties, Hertzian and half wave dipoles. Antennas: Mono pole, horn, rhombic and parabolic reflector, antenna, array and Yagi-Uda antenna. Microwave tubes: Klystron amplifier, multi-cavity klystron amplifier, Reflex Klystron oscillator, magnetron, TWT amplifier, BWO. EEE 421 Microwave Engineering Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 420. EEE 432 Digital Communication 3 Credits, 3 hours/week Introduction: Communication channels, mathematical model and characteristics, probability and stochastic process. Source Coding: Mathematical models of information, entropy, Huffman code and linear predictive coding. Digital Transmission System: Base band digital transmission, inter-symbol interference, bandwidth, power efficiency, modulation and coding trade-off.

Receiver for AWGN Channels: Correlation demodulator, match filter demodulator and maximum likelihood receiver. Channel Capacity and Coding: Channel models and capacities and random selection of codes. Block Codes and Conventional Codes: Linear block codes, convolution codes and coded modulation, Spread spectrum signals and system. Communication Systems Design: Design parameters, channel selection criteria and performance simulation EEE 433 Digital communication Lab. 1.5 Credits, 3 hours/week Laboratory experiments based on theory and concepts learnt in EEE 432. Design of simple systems using the principles learned in EEE 432. EEE 440 Optoelectronics 3 Credits, 3 hours/week Optical Properties of Semiconductor: Direct and indirect band-gap materials, radiative and non-radiative recombination, optical absorption, photo-generated excess carriers, minority carrier life time, luminescence and quantum efficiency in radiation. Properties of Light: Particle and wave nature of light, polarization, interference, diffraction and blackbody radiation. Light Emitting Diode (LED): Principles, materials for visible and infrared LED, internal and external efficiency, loss mechanism, structure and coupling to optical fibers. Stimulated Emission and Light Amplification: Spontaneous and stimulated emission, Einstein relations, population inversion, absorption of radiation, optical feedback and threshold conditions. Semiconductor Lasers: Population inversion in degenerate semiconductors, laser cavity, operating wavelength, threshold current density, power output, hetero-junction lasers, optical and electrical confinement. Introduction to quantum well lasers. Photo Detectors: Photoconductors, junction photo-detectors, PIN detectors, avalanche photodiodes and phototransistors. Solar Cells: Solar energy and spectrum, silicon and Schottkey solar cells. Modulation of Light: Phase and amplitude modulation, electro-optic effect, acousto-optic effect and magneto-optic devices, introduction to integrated optics. Books Recommended: 1. Fiber optic communications-Joseph C. Palais 2. Optoelectronics: An Introduction-J. Wilson, J. Hawkes 3. Optoelectronics and photonics Principles and Practices-S.O. Kasap

EEE 450 VLSI 3 Credits, 3 hours/week

VLSI technology: Top down design approach, technology trends and design styles. Review of MOS transistor theory: Threshold voltage, body effect, I-V equations and characteristics, latch-up problems, NMOS inverter, CMOS inverter, pass-transistor and transmission gates.

CMOS circuit characteristics and performance estimation: Resistance, capacitance, rise and fall times, delay, gate transistor sizing and power consumption. CMOS circuit and logic design: Layout design rules and physical design of simple logic gates. CMOS subsystem design: Adders, multiplier and memory system, arithmetic logic unit.Programmable logic arrays.I/O systems. VLSI testing

EEE 451 VLSI Lab 1.5 Credits, 3 hours/week

This course consists of two parts. In the first part, students will perform experiments to verify practically the theories and concepts learned in EEE 450. In the second part, students will design simple systems using the principles learned in EEE 450

EEE 452 Optical Fiber Communication 3 Credits, 3 hours/week Light Propagation through Optical Fiber: Ray optics theory and mode theory. Optical fiber: Types and characteristics, transmission characteristics, fiber joints and fiber couples. Receiver Analysis: Direct detection and coherent detection, noise and limitations. Transmission Limitation: Chromatic dispersion, nonlinear refraction, four wave mixing and laser phase noises. Optical Amplifier: Principle, application, and limitations of laser and fiber amplifiers, EDFA. Optical networks, fiber installation and optical measurement Multi-Channel Optical System: Frequency division multiplexing, wavelength division multiplexing and co-channel interference. Chromatic Dispersion: Normal and anomalous dispersion, higher order dispersion, modal dispersion and PMD. Nonlinear effects- self phase and cross-phase modulations, four wave mixing. Scattering, leakage and absorption losses. EEE 462 Computer Networks & Data Communication 3Credits, 3 hours/week Introduction: Uses of computer networks to computer communication networks and layered architecture view, LAN, WAN, Packet switching and fast packet switching, Reference models, The OSI reference model, The TCP/IP reference model, A comparison of the OSI and TCP reference models. The Data Link Layer: Data link layer design issues, Elementary data link protocols, An unrestricted simplex protocol, A simplex stop and wait protocol, Sliding windows protocols, HDLC-High-level data link Control, Data link layer in the internet, The data link later in ATM. The Network, Transport and Application Layers: The IP protocol, IP address, Sub nets, Internet control protocols, Mobile IP, Routing algorithms. Introduction to TCP, connectionless and connection oriented protocol, Flow control in Transport layer, Network security, DNS-domain name system, Electronic mail, FAX, The World Wide Web. Multiple Access Protocols: ALOHA, Carrier Sense Multiple Access (CSMA) protocols, Collision-free protocols, Limited contention protocols, Wavelength division multiple access protocols, Wireless LAN protocols, CSMA/CA, CSMD/CD: Persistent and non-persistent algorithms, Ethernet network, Different network devices: Hubs, Bridges, Switches, Router/Gateway, Spanning tree

EEE 480 Mobile Cellular Communication 3 Credits, 3 hours/week Introduction: Concept, evolution and fundamentals, analog and digital cellular systems. Cellular Radio System: Frequency reuse, co-channel interference, cell splitting and components Mobile Radio Propagation: Propagation characteristics, models for radio propagation, antenna at cell site and mobile antenna. Frequency Management and Channel Assignment: Fundamentals, spectrum utilization, fundamentals of channel assignment, traffic and channel assignment. Handoffs and Dropped Calls: Reasons and types, forced handoffs, mobile assisted handoffs and dropped call rate. Diversity Techniques: Concept of diversity branch and signal paths, carrier to noise and carrier to interference ratio performance. Multiplexing: TDM- principle, receiver synchronization, frame synchronization, TDM of multiple bit rate systems; FDM- principle, demultiplexing; WDM, multiple access network- TDMA, FDMA, CDMA- spread spectrum multiplexing, coding technique and constraints of CDMA. Digital Cellular Systems: Global system for mobile, time division multiple access and code division multiple access. GSM, AMPS, GPRS, EDGE, W-CDMA, 3rd generation of mobile communication, Packet switching and data communication EEE 481 Mobile Cellular Communication Lab 0.75 Credits, 3/2 hours/week Laboratory experiments based on theory and concepts learnt in EEE 480. EEE 482 Telecommunication Engineering 3 Credits, 3 hour/week Introduction: Principle, evolution, networks, exchange and international regularly bodies. Telephone Apparatus: Microphone.Speakers, ringer, pulse and tone dialing mechanism, side-tone mechanism, local and central batteries and advanced features. Switching System: Introduction to analog system, digital switching system-space division switching, blocking probability and multistage switching, time division switching and two dimensional switching, SPC, TST, STS. Traffic Analysis: Traffic characterization, grades of service, network blocking probabilities, delay system and queuing. Modern Telephone Services and Network: Internet telephony, fascimile, integrated services digital network; asynchronous transfer mode and intelligent networks, introduction to cellular telephony and satellite communication. Radar: Introduction, radar-equation, Pulse and MTI Radar, CW and FM Radar: Delay lines and cancellers, range getting. EEE 490 Biomedical Engineering 3 Credits, 3 hours/week Medical terminology, cell physiology, membrane potential, action potential, excitation and rhythmically. Rhythmic excitation of heart. Transducers used in medical diagnostics.

Biomedical Instrumentation: Normal Electrocardiograph, ECG simulator, Watch filter, ECG amplifier, pulse beat monitor, pace marker, galvanic skin resistance detector, respiratory and suction apparatus. Electronic stethoscope. Electronic clinical thermometer, blood flow and pressure monitoring recorders, metabolic rate measurement. Special topics: Bio-telemetry, application of ultrasonic and laser in biology and medicine. Clinical X-ray equipment. Fluoroscopy. Infrared heating.

**** **** **** ****

Date post:	02-Jan-2017
Category:	Documents
Upload:	truongkhuong
View:	246 times
Download:	12 times

Download EEE 2014-2015 syllabus

Documents