Dimensions
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.Height - 101.5cm
Depth - 38.1cm
Width - 45.6cm
Bergen 5 drawer chest
Argos = 03456 400 800
557/2911
575/9576
549/4006
571/3079
576/9470
576/9470 WHITE/MIRROR
571/3079 WHITE HG549/4006 WHITE575/9576 WALNUT557/2911 OAK
Issue: 3 - 19/12/16
DR
82517
1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
�� Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
� Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
� Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
� From time to time check that
there are no loose screws on
this unit.
� This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below�
Important – Please read these instructions fully before starting assembly
� During assembly do not stand
or put weight on the product,
this could cause damage.
� Assemble the item as close
to its final position (in the same
room) as possible.
� Assemble on a soft level
surface to avoid damaging the
unit or your floor.
� Parts of the assembly will be
easier with 2 people.
� Check you have all the
components and tools listed
on the following pages.
� Remove all fittings from the
plastic bags and separate them
into their groups.
� Keep children and animals
away from the work area, small
parts could choke if swallowed.
� Make sure you have enough
space to layout the parts before
starting.
� To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
Safety and Care Advice
Please check you have all the panels listed below
Components - Panels If you have damaged or missing components,
call the Customer Helpline:
2
03456 400 800
Drawer base x4(386x299x2,5)BO2512
Drawer base x1(386x299x2,5)BO251260
2 Back Broad(974x435x2,5)BO3443
8 Drawer back x5(374x120x12,50)LA1629
@ Drawer left side x5(305x120x12,50)LA1631
! Drawer right side x5(305x120x12,50)LA1632
6 Top(456x381x15)P1985
4 Bottom(455x381x15)P1986
5 Foot(410x340x22)P1987
3 Right side(963x380x15)P2191
1 Left side(963x380x15)P2192
7 Drawer front x5(419x188x15)P4233
0 Plinth(424x92x15)P7099
9a
9b
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Eye protection
(when using a
hammer or glue)
Ruler/tape
measure0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Small
hammer
Setsquare
Spirit level
Drill
6mm Suitable drill bit
(for use with wall plug)
Flatblade screwdriver
(medium)
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170105
The screws length is measured from the head to the point (30mm screw shown).
3
Parkerscrew x 1
ZF99936B
O
Wall plug x 1
ZF99936A
N
Handle x 5
GR1978
M
felt x 6
FK1416
L
Glue x 1
FA1510
K
Drawerbase support x 32
FK1250
J
L-Bracket x 1
FK1235
I
Wood dowel x 2
FK1410
H
(5x30mm)
15mm
Large locking nut x 10
FK1012
G
(15x12mm)
12mm
Small locking nut x 10
FK1010
F
(12x10mm)Locking screw x 20
FK1011
E
(5x24mm)Euro Screw x 20
FK1301
D
(6.3x10mm)
Pozi Screw x 85
FK1309
C
(4x12.5mm)Screw x 1
FK1400
B
(4x15mm)Screw x 4
FK1322
A
(4x30mm)
Q
Runner left part A x 5
PPM1516LA
Runner left part B x 5
PM1516LB
S
Runner right part A x 5
RPM1516RA
Runner right part B x 5
PM1516RB
Assembly Instructions
4
Step 1
a: Prepare the drawer
fronts Screw 2 locking screw E
into the holes shown on the
back of each drawer
front 7 .
Note: Insert locking
screw E as far as shown.
Do not over tighten.
b: Prepare the drawer
sides Insert a small locking nut F
into the hole on left drawer
side @ and right
drawerside !.
Make sure the ‘arrow’ on Fis pointing towards the hole
in the edge of @ and !.
Put drop of glue K in the 6
holes of drawersides @ and
! before sliding them onto
the dowels of
drawerback 8.
Slide drawerbase 9 in the
grooves of the drawer-unit.
c: Turn the drawer wrap
assembly over and push onto
the drawer front 7 . Use a
phillips or flatblade
screwdriver, that is a good fit,
to turn 24mm locking nut F
as far as it will go - more than
1/2 turn.
7
!
8
@
7
a:
b:
5x
5x
5x
c:
E
E
F
F
K
F
If Highgloss,
Please remove
the protective film!
9a/b
JJ
JJ
Assembly Instructions
5
5x
d:
3
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
DD
R
R
R
R
R
C
CC
C
C
C
C
Step 1 continued
finishing the drawers
d: Turn over drawer and
slide drawerbase
supports J in corner as
shown and fix them, using
the attached screws .
b: Insert 4 Large locking
nuts G into right side 3
where shown. Make sure
the ‘arrow’ on G is pointing
towards the hole in the
edge of 3.
Screw 1 locking screw E
into the hole shown of the
right side 3 .
Note: Insert locking
screw E as far as shown.
Do not over tighten.
a:
b:
Finished
front edge
Finished
front edge
E
3
G
G
G
G
C
CC D DR
Attaching runners
Step 2
a: Fix runner right part A R
on right side 3 as shown
using euro screw drawer
D and pozi screw C.
a:
b:
Assembly Instructions
Attaching runners
Step 3
CC
C
D DP
b: Insert 4 Large locking
nuts G into left side 1
where shown. Make sure
the ‘arrow’ on G is pointing
towards the hole in the
edge of 1.
Screw 1 locking screw E
into the hole shown of the
left side 1 .
Note: Insert locking
screw E as far as shown.
Do not over tighten.
a: Fix runner left part A P
on left side 1 as shown
using euro screw drawer
D and pozi screw C.
Put drop of glue K into the
2 holes of plinth 0.
Put dowels H into the
holes of plinth 0.
6
Finished
front edge
Finished
front edge
1
CC
C
C
C
C
C
C
C
CC
C
C
C
C
D
D
D
D
D
D
D
P
P
P
P
P
D
D
D
G
G
G
G
1E
Step 4
Insert 2 Large locking
nuts G into plinth 0
where shown. Make sure
the ‘arrow’ on G is pointing
towards the hole in the
edge of 0.
H
H
10
G
G
5
4
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
Step 6
Position bottom 4 onto
foot 5 and fix with 30mm
chipboard screw A.
Screw 24mm locking
screws E into bottom 4 .
Note: Insert
locking screw Eas far as
shown.
Do not over tighten.
7
3
10
G
G
E
E
E
EA
A
A
A
1
Step - 5
b: Attaching top
Position plinth 0 onto
right side 1 .
Use a screwdriver to turn
locking nuts G clockwise
to lock.
Position right side 3 onto
plinth 0 .
Use a screwdriver to turn
locking nuts G clockwise
to lock.
a:
b:
Finished
front edge
Assembly Instructions
8
5
4
5
L
L
L
L
Step - 7
A: Attaching bottom
Position bottom 3 onto
left & right side 1 , 3.
Use a screwdriver to turn
locking nuts G clockwise
to lock.
A: Attaching felt
Stick the selfadhesive
felt L strategically
underneath the foot 5.
Finished
front edge
Assembly Instructions
Insert back board
Turn chest upright and slide
back board 5 in the groove.
Step 9
a: Prepare top
Screw 4 locking screw E
into the holes shown on top
6 .
Note: Insert
locking screw Eas far as
shown.
Do not over tighten.
9
E
E
E
E
2
6
Step - 8
Finished
front edge
Assembly Instructions
10
Fixate back board
Slide drawerbase supports
J in corner as shown and
fix them, using the attached
screws .
6
J
J
J
JJ
J
J
J
JJ
J
J
J
Step - 9 continued
Step - 10
b: Attaching top
Position top 6 onto left &
right side 1 , 3.
Use a screwdriver to turn
locking nuts G clockwise
to lock.
12
11
7
Step 11
11
5x
5x
Inserting drawers
Attaching runners
Fix runner left and right side
B Q and S on left & right
drawer side @ and ! as
shown using 12,5mm pozi
screw C.
Step 12
Step 13
Attaching drawer handle
Attacht drawer handle M on
drawer front 7 as shown
using 12,5mm pozi screw C.
Top drawer is the one with
the Warning.
Assembly Instructions
CC
C
C
C
C
CC
S
Q
C
C
C
M
Assembly Instructions
12
Assembly is complete.
Step - 1
Fixing to wall
Warning:
The chest
is heavy.
Lift with care.
and remove chest.
Drill 6mm hole and insert
wall plug N.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Reposition chest
and fix L-bracket with
screw O .
It is recommended that
the chest is fixed to a
wall.
position L-bracket I
onto top 6 as shown ,
fix by using 15mm screw
B.
Note: there are no pre-
drilledholes for 15mm
screw B
With help, move chest
into position.
13
A Guide to - Wall Mounting & Fixings
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty” wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hamemr fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.