353 2007-08 DRAG RACING PARTS AND ACCESSORIES 12-Circuit Drag Race Wiring Kit PWI50003 Redesigned Kit includes an 8-switch, non-fused control center which plugs directly into the 12-circuit Pro Street harness and fuse box. The control panel has lighted rocker switches for start, ignition, fan, two fuel pumps, water pump, lights and one accessory. Fused Circuits For: • Ignition • Brake Lights • Radio • Electric Water Pump • Headlights • Wipers • Electric Fuel Pump • Taillights • Turn Signals • Electric Fan • Horn • Flashers 12-Circuit Pro-Street Wiring Harness PWI50002 Similar to the 8- circuit race car Har- ness plus circuits for gauges, ra- dio, brake lights, wipers, head- lights, turn signals, emergency flashers, horn and coil. Includes factory terminated fuse block, 15 ft. of wire per circuit, mounting bracket, fuses, headlight plugs, terminals, grommets, wire ties and GM plugs. Fused Circuits For: • Electric Fuel Pump • Gauges • Turn Signals • Electric Water Pump • Radio • Emergency Flashers • Electric Fan • Brake Lights • Horn • Wipers • Headlights • Coil 8-Circuit Extreme Condition Wiring Harness PWI50001 Harness is protect- ed by fuses and has 30 amp relays for reliability. Large, color- coded electrical wire and fuse block are factory terminated. Assembly includes 18' of wire per circuit, terminals, wire ties, rubber grommet, fusible link and instructions. Use with non-fused 8-switch rocker panels listed below. Fused Circuits For: • Start • Ignition • Lights • Electric Water Pump • Electric Fan • Accessories • Electric Fuel Pump 1 • Electric Fuel Pump 2 Part No. Description PWI50201............... 8-Switch Non-Fused Flat Plate Panel, In-Dash Mount PWI50202............... 8-Switch Non-Fused Self Contained Panel, Roll Bar Mount 12-Circuit Universal Fuse Block PWI30001 Original equipment quality block can be added to existing wiring or used as a starting point for custom wiring. Fuse block center includes fuses, flashers, horn relay, terminals, anti-theft feature and complete instructions. Fused Circuits For: • Air Conditioning/Heat • Brake Lights • Horn • Coil (Anti-Theft) • Dome Light • Turn Signals • Electric Fan • Emergency Flashers • Wipers • Instruments • Headlights • Radio 12-Circuit Pro-Street Fuse Block PWI50101 For race cars that may see occasional street duty. Features include a 10 gauge lead-in wire for powering up circuits, fuses, flashers, horn relay, fusible link, terminals, labels, an anti-theft feature and instructions. Fused Circuits For: • Electric Fuel Pump • Electric Water Pump • Dome Light • Electric Fan • Wipers • Instruments • Turn Signals • Horn • Brake Lights • Radio • Headlights • Emergency Flashers 4-Circuit Fuse Center PWI30002 4-Circuit Fuse Center is an easy-to- assemble kit ideal for add-on accesso- ries like electric fans or fuel pumps. Fuse Center is 2" high, 3-1/2" wide and 1" deep and includes terminals. Fuses are not included. Vertical/Horizontal 6-Switch Dragster Control Center PWI50506 Painless 6-Switch Vertical/Horizontal Control Center is the perfect solution in tight spaces like dragster cockpits. Wafer-thin, 1-1/2" wide self-contained center mounts in just about any position to provide quick, unobstructed access. Fused Circuits For: • Start • Water Pump • Fuel Pump • Ignition • Accessory • Accessory Standard Features: • Complete With 18' Wiring Harness • Input Wire Is 10 Gauge, Output Wire Is 14 Gauge • Heavy-Duty, Non-Reflective, Lightweight Metal Housing • Fuses, Wire Ties, Grommets And Instructions Are Included • Factory Terminated, Fully Insulated Terminals Resist Vibration • Switch Functions Are Screen Printed For Quick Visual Reference • Color-Coded Rocker Switches Light Up When Pushed (Except Start) PWI50202
Transcript
3532007-08 DRAG RACING PARTS AND ACCESSORIES
12-Circuit Drag Race Wiring Kit PWI50003Redesigned Kit includes
an 8-switch, non-fused control center which plugs directly into the 12-circuit Pro Street harness and fuse box. The control panel has lighted rocker switches for start, ignition, fan, two fuel pumps, water pump, lights and one accessory.Fused Circuits For:
• Ignition • Brake Lights • Radio• Electric Water Pump • Headlights • Wipers• Electric Fuel Pump • Taillights • Turn Signals• Electric Fan • Horn • Flashers
12-Circuit Pro-Street Wiring Harness PWI50002Similar to the 8-
circuit race car Har-ness plus circuits for gauges, ra-dio, brake lights, wipers, head-lights, turn signals, emergency flashers, horn and coil. Includes factory terminated fuse block, 15 ft. of wire per circuit, mounting bracket, fuses, headlight plugs, terminals, grommets, wire ties and GM plugs.Fused Circuits For:
• Electric Fuel Pump • Gauges • Turn Signals• Electric Water Pump • Radio • Emergency Flashers• Electric Fan • Brake Lights • Horn• Wipers • Headlights • Coil
8-Circuit Extreme Condition Wiring Harness PWI50001Harness is protect-
ed by fuses and has 30 amp relays for reliability. Large, color-coded electrical wire and fuse block are factory terminated. Assembly includes 18' of wire per circuit, terminals, wire ties, rubber grommet, fusible link and instructions. Use with non-fused 8-switch rocker panels listed below.Fused Circuits For:
• Start • Ignition • Lights• Electric Water Pump • Electric Fan • Accessories• Electric Fuel Pump 1 • Electric Fuel Pump 2
Part No. DescriptionPWI50201 ............... 8-Switch Non-Fused Flat Plate Panel, In-Dash MountPWI50202 ............... 8-Switch Non-Fused Self Contained Panel, Roll Bar Mount
block can be added to existing wiring or used as a starting point for custom wiring. Fuse block center includes fuses, flashers, horn relay, terminals, anti-theft feature and complete instructions.Fused Circuits For:
• Air Conditioning/Heat • Brake Lights • Horn• Coil (Anti-Theft) • Dome Light • Turn Signals• Electric Fan • Emergency Flashers • Wipers• Instruments • Headlights • Radio
12-Circuit Pro-Street Fuse Block PWI50101For race cars that may
see occasional street duty. Features include a 10 gauge lead-in wire for powering up circuits, fuses, flashers, horn relay, fusible link, terminals, labels, an anti-theft feature and instructions.Fused Circuits For:
• Electric Fuel Pump • Electric Water Pump • Dome Light• Electric Fan • Wipers • Instruments• Turn Signals • Horn • Brake Lights• Radio • Headlights • Emergency Flashers
4-Circuit Fuse Center PWI300024-Circuit Fuse Center is an easy-to-
assemble kit ideal for add-on accesso-ries like electric fans or fuel pumps. Fuse Center is 2" high, 3-1/2" wide and 1" deep and includes terminals. Fuses are not included.
Vertical/Horizontal 6-Switch Dragster Control Center PWI50506Painless 6-Switch
Vertical/Horizontal Control Center is the perfect solution in tight spaces like dragster cockpits. Wafer-thin, 1-1/2" wide self-contained center mounts in just about any position to provide quick, unobstructed access.Fused Circuits For:
Standard Features:• Complete With 18' Wiring Harness• Input Wire Is 10 Gauge, Output Wire Is 14 Gauge• Heavy-Duty, Non-Reflective, Lightweight Metal Housing• Fuses, Wire Ties, Grommets And Instructions Are Included• Factory Terminated, Fully Insulated Terminals Resist Vibration• Switch Functions Are Screen Printed For Quick Visual Reference• Color-Coded Rocker Switches Light Up When Pushed (Except Start)
PWI50202
354 2007-08 DRAG RACING PARTS AND ACCESSORIES
4-, 6-, And 8-Switch, Self-Contained Fused Control CentersStandard Features:
• Complete with 18' wiring harness• Easy-to-follow instructions included• Input wire is 10 gauge, Output wire is 14 gauge• Heavy-duty, non-reflective, lightweight metal housing• Factory terminated, fully insulated terminals resist vibration• GM color-coded, high temperature wire is rated at 600 volts• Switch functions are screen printed for quick visual reference• Circuits are individually fused with automotive blade-type fuses• Color-coded rocker switches light up when pushed (except start)
Part No. PWI50301 PWI50302 PWI50303Height 3" 3" 3"Width 5-3/4" 8-1/4" 10-3/4"Depth 3-1/8" 3-1/8" 3-1/8"No. Of Switches 4 6 8Switch FunctionsStart X X XIgnition X X XWater Pump/Fan** XWater Pump XElectric Fan XFuel Pump 1* X XFuel Pump 2* XLights XAccessory XAccessory* X X XAccessory* X*For safety, these switches are only powered when ignition is on.**Three position switch: Water Pump/Off/Water Pump and Fan.
Mustang Switch PanelsA line of Panels engineered specifically for 5.0/4.6L
Mustangs. Ideal for street/strip cars, each panel con-tains the highest quality switches and durable, high temperature TXL wire.
Hide-A-PanelMounts in the original ashtray loca-
tion and provides a convenient spot for fuel pump, water pump, electric fan or nitrous activation. Fully assembled, lighted rocker switch panels fit into any ’87-97 5.0/4.6L Mustang.Part No. DescriptionPWI50212 .......Hide-A-Panel, Includes Four Rocker Switches PWI50422 .......Nitrous Hide-A-Panel, Includes Three Rocker Switches And
One Momentary Switch For Purge
Rocker/Toggle Switch PanelsPanels fit into the original
radio/stereo location of late model Mus-tang. Choose tradition-al toggle switches with corresponding colored LED’s or lighted rocker switches.Part No. DescriptionPWI50210 ....... ’79-86 Mustang Rocker Switch Panel, Six On/Off Switches,
One Lighted Momentary And One Unlighted Momentary SwitchPWI50211 ....... ’87-93 Mustang Rocker Switch Panel, Six On/Off Switches,
One Lighted Momentary And One Unlighted Momentary SwitchPWI50420 ....... ’79-86 Mustang Toggle Switch Panel, Six Toggle Switches,
One Momentary And One On/OffPWI50421 ....... ’87-93 Mustang Toggle Switch Panel, Six Toggle Switches,
One Momentary And One On/OffPWI50430 ....... ’87-93 Mustang Carbon Fiber Rocker Switch Panel, Six On/Off Switches,
One Lighted Momentary And One Unlighted Momentary Switch
Rocker Switch Panels With Circuit BreakersPopular drag race Switch
Panels are better than ever with circuit breakers in place of standard fuse. If a circuit blows, it can be quickly reset at the touch of a finger. Panels also have color-coded, lighted rocker switches, high grade TXL wire, vibra-tion resistant terminals and a glare resistant black finish.Part No. DescriptionPWI50305 .......6-Switch Rocker Circuit Breaker PanelPWI50306 .......8-Switch Rocker Circuit Breaker PanelPWI50507 .......6-Switch Vertical/Horizontal Rocker Circuit Breaker Panel
Universal Fuel Pump Relay Kit PWI50102Electric fuel pumps need high
amperage which may damage the electrical system. Avoid prob-lems with the Relay Kit which includes 6' power wire, 30 amp circuit breaker and relay, 15' output wire, terminal ends and instructions.
Fan-Thom Electric Fan Relay KitsThe Fan-Thom Relay Kit will protect the electric fan
and the electrical system. Kit includes a 30 amp circuit breaker, heavy duty relay, wiring harness and terminals. The Fan-Thom Relay is also available with a choice of pre-set ther-mostatic switches to activate the electric fan auto-matically.Part No. DescriptionPWI30101 ....... Fan Relay KitPWI30102 ....... Fan Relay Kit With 200° On/185° Off Thermostatic ActivationPWI30103 ....... Fan Relay Kit With 185° On/170° Off Thermostatic Activation
Electric Water Pump Relay PWI50106Relay supplies maximum battery
voltage to the electric pump and pro-tects the main electrical system from overloads.
Tim Ferguson
3552007-08 DRAG RACING PARTS AND ACCESSORIES
Header Flange KitsIdeal for custom
header fabrication, Kits are offered for most popular engines, includes gaskets and fas-teners.
Part No. Application Flange Thk. Tube Dia.PEPH7864 SB Chevy 265-400 5/16" 1-5/8"PEPH7894 SB Chevy 265-400 5/16" 1-3/4"PEPH7899 BB Chevy 396-454 3/8" 1-3/4"-2"PEPH7842 SB Ford 289-351W 5/16" 1-5/8"PEPH7870 SB Ford 289-351W 5/16" 1-3/4"PEPH7871 BB Ford 429-460 5/16" 2"
Formed CollectorsCollectors have long transitions for
better flow. Sold in pairs.Part No. Tube Dia. Collector Dia. Length
“Critical Link” Carbon Fiber DriveshaftsPST “Critical Link” Carbon Fiber 1350 Driveshafts are significantly lighter and stronger than alu-
minum or steel for unparalleled smoothness and shock reduction. Strong, solid non-lube 1350 series U-joints and forged tube yokes are bonded to 3-3/4" diameter, carbon fiber tubing. Replacement carbon fiber driveshafts are also available for late model Mustangs, Cama-ros and Firebirds. Drag race driveshafts are available by special order only. PST also offers mild or chrome moly steel and 6061-T6 aluminum driveshafts. Contact your sales representative for more information. Specify measurements and with or without yokes when ordering.
Drag Racing Analyzer V3.2 PFTDRA32CComputer program simulates, predicts and analyzes
drag racing performance on either the 1/8 or 1/4 mile – like having a drag strip, dyno and chassis shop right in the computer. DOS program can simulate any combination and predict how the car will respond to changes. User can input actual or simulated engine and vehicle specifications, transmission and rear end gear ratios, wheel/tire sizes, launch RPM, shift points and even weather conditions. Analyzer produces results in horsepower, elapsed time, MPH, elapsed time per gear, G-forces, feet per second, etc. Includes disc and infor-mative manual packed full of detailed examples to show how the program works.
Engine Analyzer V3.2 PFTEA32CVersion 3.2 can simulate, predict and analyze stock
or race engine performance. Change specs for cam, manifold or headers and see the effects. Engine output is through torque, horsepower or value plots. Compatible with Windows 95, 98, NT, Me, 2000 and XP.
Engine Analyzer Pro V3.3 PFTEAP33CAdvanced software can simulate a variety of engine
build-ups and modifications. Evaluate change of cam, cylinder head, intake, headers, super-chargers, etc. and subsequent effects on torque, horsepower, air flow, fuel flow, cylinder pressure, and volumetric efficiency. An in-formative 260 page manual is included. Compatible with Windows 95, 98, NT, Me, 2000 and XP. Jeff Ledford
3572007-08 DRAG RACING PARTS AND ACCESSORIES
Plasma-Moly File Fit Piston Ring SetsPerfect Circle File Fit Ring Sets reduce friction, increase
power output, reduce oil consumption and last longer. Sets include eight ductile iron plasma-moly top rings, THG (tapered hook groove) second compression rings and CP-20 oil control rings. V8 piston ring sets listed include standard tension oil rings unless specified. Sets with low tension oil rings are for racing engines only.
Turbo Flex Standard Electric FansStraight blade, low profile fans are
mounted within a shroud assembly and are perfect for limited space or auxiliary cooling use. Fans may be mounted on either side of the radiator and set-up in push or pull configuration.
Part No. Description Output DimensionsPRM19128 8" Dia. 800 CFM 8" x 10" x 2-1/4"PRM19120 10" Dia. 900 CFM 11" x 10" x 2-1/4"PRM19122 12" Dia. 1,200 CFM 13-3/4" x 12-1/2" x 2-3/4"PRM19124 14" Dia. 1,650 CFM 15-1/2" x 14" x 3-15/16"PRM19126 16" Dia. 2,100 CFM 17" x 16" x 3-1/4"
Turbo Flex High Performance Electric FansAmong the most powerful Electric
Fans available, Turbo Flex High Per-formance Fans are capable of moving almost twice the volume of other fans. Fans feature lightweight nylon or aluminum blade assemblies and open steel fan housings. Fans are reversible and may be mounted on either side of radiator.
Part No. Description Output DimensionsPRM19010 10" Dia. 1,250 CFM 13" x 10-1/2" x 2-1/2"PRM19008 12" Dia. 1,650 CFM 12-1/2" x 12-1/2" x 3-3/4"PRM19114 14" Dia. 2,950 CFM 14" x 14" x 3-3/4"PRM19115 16" Dia. 2,950 CFM 16" x 16" x 3-3/4"PRM19117 18" Dia. 2,500 CFM 17-3/4" x 17-3/4" x 3-3/4"
Turbo Flex Electric Fan Installation AccessoriesPart No. DescriptionPRM18905 .....Adjustable Wiring Kit, 170-210°F Adjustable Thermal Switch, Probe
(Installs Between Radiator Fins), Wiring And ConnectorsPRM18907 .....Adjustable Wiring Kit, 170-210°F Adjustable Thermal Switch, Probe
(Installs Into Manifold/Cyl. Head), Wiring And ConnectorsPRM19001 .....Standard Wiring Kit, 170°F Automatic Thermal Switch, Wiring And
Electric Fan Module PRM12311Fan Module provides maxi-
mum cooling for engine oil or transmission fluid. Unit is 10-1/2" x 14" x 3-3/4" with 3/8"NPT female ends and includes a 10" fan capable of 900 CFM.
Maxi-Cool Junior Cooler PRM13511The cure for soaring transmission temperatures, Maxi-
Cool Junior Cooler has a built-in, 10" 900 CFM electric fan and Turbolator heat sink inserts in 1/2" dia. alumi-num tubes with 3/4" aluminum fins. Dimensions are 3" x 10" x 12-1/2". Includes -6AN male fittings.
Thin Line Transmission Cooler KitsKits improve performance and
extend transmission life. Light-weight, compact, 3/4" thick coolers are perfect for limited space. Cooler Kits include instal-lation hardware.Part No. DescriptionStandard Transmission Coolers, 11/32" Multi-Barb FittingsPRM1010 .......12,000-14,000 GVW Transmission Cooler Kit, 5" x 12-1/2"PRM1011 .......14,000-16,000 GVW Transmission Cooler Kit, 5" x 15-1/2"PRM1012 .......16,000-18,000 GVW Transmission Cooler Kit, 7-1/2" x 12-1/2"PRM1013 .......18,000-20,000 GVW Transmission Cooler Kit, 7-1/2" x 15-1/2"PRM1014 .......22,000-24,000 GVW Transmission Cooler Kit, 10" x 15-1/2"PRM1015 .......20,000-22,000 GVW Transmission Cooler Kit, 10" x 12-1/2"Competition Transmission Coolers, -6AN Male FittingsPRM1021* ......14,000-16,000 GVW Transmission Cooler Kit, 5" x 15-1/2"PRM1024* ......22,000-24,000 GVW Transmission Cooler Kit, 10" x 15-1/2"Transmission Cooler Installation AccessoriesPRM104 .........Metal Mounting Kit, Includes Two Zinc-Plated Steel Mounting
Brackets And HardwarePRM105 .........Universal Mounting Kit, Includes Four Nylon Tie Mounts And
Protective Foam Pads *Hose not included.
H.D. Frame Rail Transmission CoolersCompact, easily mounted Coolers are ideal for drag
race cars with limited mounting space. Highly efficient, coil helps extend transmission life. Choose stand-off or flush mount with 3/8"NPT female or 11/32" hose barb fittings.
DescriptionStand-Off Part No.
Flush Mount Part No.
1-1/2" x 3-1/2" x 12", 11/32" Hose Barb PRM6112 PRM71121-1/2" x 3-1/2" x 12", 3/8"NPT PRM6312 PRM73122-3/4" x 3-1/2" x 15", 11/32" Hose Barb PRM6115 PRM71152-3/4" x 3-1/2" x 15", 3/8"NPT PRM6315 PRM73152-3/4" x 3-1/2" x 18", 11/32" Hose Barb PRM6118 PRM71182-3/4" x 3-1/2" x 18", 3/8"NPT PRM6318 PRM73182-3/4" x 3-1/2" x 21", 11/32" Hose Barb PRM6121 PRM71212-3/4" x 3-1/2" x 21", 3/8"NPT PRM6321 PRM7321
PRM19120
PRM19010
PRM1010
PRM1015
PRM6321
Don Klooster Photos By Caswell Photography
3592007-08 DRAG RACING PARTS AND ACCESSORIES
Gasket MakersIncreased use of aluminum, bi-metal alloys,
and high tech plastics has created the need for superior RTV silicone Gasket Makers. Permatex offers carded tubes or cartridges.
Description CardedCarded
Oz. CartridgeCartridge
Oz. Temp.Ultra Black PEX82180 3.35 PEX24105 10.6 -75° To 625°Ultra Blue No Leak PEX81724 3.35 PEX81725 13 -75° To 500°Ultra Copper Hi-Temp PEX81878 3 – – -75° To 700°Blue Sensor Safe PEX80022 3 – – -65° To 500°Hi-Temp PEX81160 3 PEX81409 11 -75° To 650°Sensor Safe Hi-Temp PEX81422 3 – – -75° To 650°
The Right Stuff Gasket MakerRepair leaks quickly with The Right Stuff
leakproof Gasket Maker. Modern rubber gasket technology is incorporated in this product which is used on production lines by GM, Ford and Chrysler. Temperature range is -75° to 450°F.Part No. DescriptionPEX25223 .......4 Oz. TubePEX25224 .......7 Oz. TubePEX29208 .......5 Oz. CartridgePEX33694 .......10 Oz. Tube
transfer and prevents gasket burnout. Seals minor surface imperfections instantly. Ideal for head, exhaust manifold and carburetor gas-kets. Temperature range -50° to 500°F. Sold in a 12 oz. aerosol can.
High Performance Thread Sealant PEX56521Formulated for tapered pipe fittings, Sealant
replaces Teflon tape or pipe dope. Works well on head bolts (that pass through water jackets), sending units, sensors, fuel fittings, oil and coolant lines, and rear axle fill plugs. 50ml tube.
High Temperature Thread SealantsSealant is used to lock and seal threaded
fittings or bolts. Often used on head bolts (that enter water jackets), oil sending units, fuel fittings, rear axle plugs, brake and power steering fittings, etc.Part No. DescriptionPEX59214 .......6ml Carded TubePEX59235 .......50ml Carded Tube
PermaPoxy PEX84101Easy-to-use, 2-part epoxy
bonds metal, fiberglass, rubber, plastic, etc. Sold in a .84 oz. carded syringe.
Thread Sealant With TeflonA general purpose fitting Sealant. Remains pliable at
high or low temperatures. Effective from -65° to 300°F.Part No. DescriptionPEX80631 .......1 Oz. TubePEX80632 .......4 Oz. Can
ThreadlockersDeveloped to positively lock and seal
threaded fasteners. Threadlockers fill the space between threads on metal parts and then harden for a tough, adhesive bond and seal. Part No. DescriptionPEX24200 .......Removable Strength Blue, Carded 6ml TubePEX24240 .......Medium Strength Blue, Carded 36ml BottlePEX24300 .......Medium Strength Blue, Carded 10ml BottlePEX27100 .......Hi-Strength Red, Carded 6ml TubePEX27140 .......High Strength Red, Carded 36ml BottlePEX27200 .......Hi-Temp/Hi-Strength Red, Carded 10ml Bottle
Anti-Seize LubricantBlend of aluminum, copper and graphite
lubricants prevents galling, corrosion and seizing for easier disassembly. Works well anywhere, including lubrication of slip-on collectors, adjustable header tubes or any other exhaust tubing for easier disassem-bly. Effective from -60° to 1200°F.Part No. DescriptionPEX80078 .......8 Oz. Brush-Top BottlePEX81343 .......1 Oz. Carded Tube
Ultra-Slick Engine Assembly Lube PEX81950Ultra-Slick prevents galling and scuffing during
critical initial engine start-up. Superior adhesion qualities meet or exceed stock performance spec-ifications for engine Assembly Lubricant. Use on bearings, camshafts, lifters, valves, guides, and rocker shaft assemblies. 4 oz. bottle.
Fast Orange Hand CleanersThe #1 selling, biodegradable, waterless,
petroleum solvent-free hand cleaner. Contains no harsh chemicals, mineral oils or ammonia that can irritate cuts and abrasions.Part No. DescriptionPEX25108 ....... Fine Pumice Cleaner, 7.5 Oz. BottlePEX25116 ....... Fine Pumice Cleaner, 15 Oz. BottlePEX25218 ....... Fine Pumice Cleaner, 1 Gal. Bottle With PumpPEX25025 .......Hand Cleaner Wipes, 25 Count
Disposable Nitrile Gloves100% synthetic rubber Gloves have
textured fingers for secure grip and offer protection from a variety of hazardous chemicals. Boxes of 100, in medium, large and X-large.
Description Med. Part No. Large Part No. X-Lg. Part No.Nitrile Gloves PEX09184 PEX09185 PEX09186
Ground Shipment OnlyOn All Permatex Products
Listed Except Gloves.
Ground Shipment OnlyOn All Permatex Products Listed Except Gloves.
360 2007-08 DRAG RACING PARTS AND ACCESSORIES
“Ignitor” Conversion KitsReplaces stock points and con-
denser with Hall Effect integrated circuitry. Controls dwell to within 1/4° accuracy. No external boxes are required, and the ignitor fits entirely under the distributor cap. Delivers twice the voltage of a points system. Ignitors will also work with an MSD amplifier box. Retain a factory look with the reliability of modern electronics. Use with a Flame-Thrower coil.Part No. DescriptionPRT1181 ........GM ’57-74 V8 Most Single Points Distributors. Uses A Magnetic RingPRT1181LS .....GM ’57-74 V8 Most Single Points Distributors. Uses Lobe SensorPRT1281 ........ Ford ’57-74 V8 Single Points Distributors
“Ignitor II” Conversion KitsCompared to a breaker
points system, the Ig-nitor II averages four times more available energy between 3000 and 5000 RPM. The Ignitor II, with Hall Effect integrated circuitry, has an average of three times more available energy and twice the available spark plug voltage of the original Ignitor. The best choice for engines that will frequently see 3000 RPM and above. Use with a Flame-Thrower II ignition coil.Part No. DescriptionPRT91181 ......GM ’57-74 V8 Most Single Points DistributorPRT91281 ...... Ford ’57-74 V8 Single Points Distributor
Flame-Thrower CoilsThe Flame-Thrower Coils produce
40,000 volts and are available in black or chrome. For use with inductive or Ignitor ignition systems.Part No. DescriptionPRT40001 ......Chrome Flame-Thrower Coil. Oil Filled, 1.5 OHMPRT40011 ......Black Flame-Thrower Coil, Oil Filled, 1.5 OHMPRT40111 ......Epoxy (Black) Flame-Thrower Coil, 1.5 OHM
Flame-Thrower II CoilsThe Flame-Thrower II Coils put out an incred-
ible 45,000 volts. Compatible for use with Ig-nitor II or capacitive discharge ignition systems.Part No. DescriptionPRT45001 ......Chrome Flame-Thrower II Coil, Oil Filled, 0.6 OhmPRT45011 ......Black Flame-Thrower II Coil, Oil Filled, 0.6 OhmPRT45111 ......Epoxy (Black) Flame-Thrower II Coil, 0.6 Ohm
Flame-Thrower Digital Rev Limiter PRT600Digital Rev Limiter is
compatible with any 4, 6 or 8 cylinder engine using points, original equipment electronic (GM HEI, Ford, Chrysler) or aftermarket inductive ignition systems including the Ignitor and Ignitor II. The unit’s small size (2.5" x 3" x 1.4") and four-wire hook-up make it easy to install. Setting is easy with exter-nal digital rotary switches (eliminate RPM “chips”).
Flame-Thrower Billet “Plug N Play” DistributorsAffordable performance, ideal replace-
ment for points or stock electronic distribu-tors. Features the patented Ignitor II module, a 6061-T6 polished billet aluminum housing and a tempered .500" dia. shaft. Compatible with multiple spark CD boxes. Available with or with-out vacuum advance and with choice of male or female style distributor caps. Distributors listed fit all Chevy V8 engines except 348 and 409.
Description Black Cap Red CapVacuum Advance Distributors
Chevy, Std. Deck Ht., Female Cap PRTD100700 PRTD100701Chevy, Std. Deck Ht., Male Cap PRTD100710 PRTD100711
Non-Vacuum Advance DistributorsChevy, Std. Deck Ht., Female Cap PRTD100800 PRTD100801Chevy, Std. Deck Ht., Male Cap PRTD100810 PRTD100811
Flame-Thrower Race HEI Distributors48% more peak current than Street/Strip
distributors, with vacuum lockouts to prevent improper timing changes. High dielectric strength caps with brass terminals, balanced rotors, high output coils and modules are included. Black or red caps.
Description Black Cap Red CapChevy V8, All Exc. 348-409, Cast Housing PRTD1070 PRTD1071
Flame-Thrower Street/Strip HEI DistributorsHigh performance modules and coils
deliver superior performance up to 7500 RPM. Choose cast or machined aluminum hous-ings with adjustable vacuum advance canisters, high performance mechanical advances, balanced rotors and high dielectric strength caps with brass terminals. Black, red or blue caps.
Description Black Cap Red Cap Blue CapChevy V8, All Exc. 348-409, Cast Housing PRTD1000 PRTD1001 PRTD1002
Flame-Thrower HEI Tune-Up KitsTune-Up Kits have everything needed to improve a stock
GM HEI distributor. Kits include coil, module, high dielectric strength cap, rotor, coil cover, adjustable vacuum advance, high performance advance kit, wiring harness, capaci-tor and hardware. Cap and rotor kits are also offered.
Description Black Cap Red Cap Blue CapChevy/Cadillac V8, 4-Pin Module PRTD8000 PRTD8001 PRTD8002
Buick/Olds/Pontiac/’81-91 Vette V8, 4-Pin Mod. PRTD8010 – PRTD8012Cap And Rotor Only Kit, All GM V8 PRTD4000 PRTD4001 PRTD4002
3612007-08 DRAG RACING PARTS AND ACCESSORIES
WET-VAC Single-Stage Wet Sump External Oil Pump/Vacuum PumpPump has a 1.100" pressure
rotor and four .875" scav-enge rotors to pull vacuum in the engine. Readings of 11" to 14" are typical. Use with the PTR08-0455 Adjustable Vacuum Regula-tor and mount with standard Bearclaw mount plates.Part No. DescriptionPTR03-3842 ... Left Side Mount Pump, High VolumePTR03-3852 ...Right Side Mount Pump, High Volume
Pro Series Dry Sump Oil PumpsPeterson’s Pro Series Dry Sump Oil Pumps use a su-
perior gerotor design for maximum efficiency. Each fully CNC-machined pump is fitted with tubular dowels and O-rings for accurate alignment and leak-free operation. Offered in 3-, 4 and 5-stage versions, modular pumps have true, bolt-in scavenge manifolds for lower profile and easier installation. The pressure “in” fitting at the rear of the pump eases plumbing on most applications.Note: Stages refer to the total number of pumping bodies which include one pressure section. For example, four-stage pump includes one pressure section and three scavenging sections.
Pumps allow adjusting both idle and top end oil pressure. When com-bined with the available internal scavenge manifold and bolt-on fittings, modu-lar pump delivers a low pro-file, compact package. Pumps may be fitted with a wide variety of options to suit an array of applications.Part No. DescriptionPTR03-3201 ...3-Stage, Left Side Mount, Std. PressurePTR03-4201 ...4-Stage, Left Side Mount, Std. PressurePTR03-5201 ...5-Stage, Left Side Mount, Std. Pressure
Wet And Dry Sump Oil Pump Mount PlatesBecause Peterson’s gerotor gears minimize vibration,
only one billet aluminum Plate is needed to mount their wet or dry sump pumps.Part No. DescriptionPTR06-3001 ...SB Chevy Lt. Side Mount Plate, Fits PTR03-3001, PTR03-4001,
PTR03-5001 PumpsPTR06-3013 ...BB Chevy Lt. Side Mount Plate, Fits PTR03-3013, PTR03-4013,
PTR03-5013 PumpsPTR06-3034 ...SB Chevy Bearclaw Lt. Side Mount Plate, Fits PTR03-3802 PumpPTR06-3035 ...SB Chevy Bearclaw Rt. Side Mount Plate, Fits PTR03-3852 PumpPTR06-3044 ...BB Chevy Bearclaw Lt. Side Mount Plate, Fits PTR03-3802 PumpPTR06-3045 ...BB Chevy Bearclaw Rt. Side Mount Plate, Fits PTR03-3852 Pump
Pro Rotor Pump Fittings-Flange StylePart No. DescriptionScavenge In/Pressure Out Small 4-Bolt FlangePTR15-1101 ... -10AN x Small Port Pro RotorPTR15-1102 ... -12AN x Small Port Pro RotorPTR15-1141 ... -10AN x 45° Small Port Pro RotorPTR15-1142 ... -12AN x 45° Small Port Pro RotorRear Inlet Pressure In/Scavenge Out Large 4-Bolt FlangePTR15-1103 ... -12AN x Large Port Pro RotorPTR15-1104 ... -16AN x Large Port Pro RotorPTR15-1105 ... -12AN x 90° Large Port Pro RotorPTR15-1106 ... -16AN x 90° Large Port Pro Rotor Side Inlet Pressure In, Oval PortPTR15-1109 ... -16AN x Oval Port Pro RotorPTR15-1110 ... -12AN x Oval Port Pro Rotor
Dry Sump Pump Fittings - Male ThreadLarge bore, anodized fittings are radiused to provide
maximum oil flow. Part No. DescriptionPTR15-1005 ... -10AN x -10AN PortPTR15-1006 ... -12AN x -10AN PortPTR15-1007 ... -16AN x -10AN Port
Direct Mount Scavenge ManifoldsPeterson’s aluminum Direct Mount Scavenge Manifolds
attach directly to the pump, reducing the hoses necessary to return scav-enge oil from the pump to the tank.Part No. DescriptionPTR10-0100 ...3-Stage, -12, -12, -12 Peterson PumpPTR10-0101 ...3-Stage, -12, -12, -16 Peterson PumpPTR10-0103 ...4-Stage, -12, -12, -12, -16 Peterson PumpPTR10-0300 ...3-Stage, -12, -12, -12 Weaver, SCP PumpPTR10-0301 ...3-Stage, -12, -12, -16 Weaver, SCP PumpPTR10-0302 ...4-Stage, -12, -12, -12, -12 Weaver, SCP PumpPTR10-0303 ...4-Stage, -12, -12, -12, -16 Weaver, SCP Pump
Oil Return ManifoldsPrimarily used with dry sump systems to consolidate
HTD BeltsTeeth on HTD (High Torque Drive) Belts engage more
deeply into the pulley, for more load carrying capability, especially in severe applications. Belts are 20mm wide with an 8mm pitch. Suitable for applications normally serviced by chain or gear drive systems.Part No. Description20mm Wide HTD BeltsPTR05-1900 ...480mmPTR05-1901 ...536mmPTR05-1902 ...560mmPTR05-1903 ...600mmPTR05-1904 ...632mmPTR05-1905 ...640mmPTR05-1906 ...720mmPTR05-1907 ...800mmPTR05-1908 ...624mmPTR05-1909 ...656mmPTR05-1910 ...680mm30mm Wide HTD BeltsPTR05-1931 ...536mmPTR05-1933 ...600mmPTR05-1935 ...640mmPTR05-1939 ...656mm
press into the pulley and act as belt guides. Flanges fit Peterson pulleys, but may not fit pulleys manufactured by other compa-nies. Sold in pairs.Part No. DescriptionPTR05-0628 ... For PTR05-0328, PTR05-1334 Or PTR05-1335, 28T PulleyPTR05-0632 ... For PTR05-0332, 32T PulleyPTR05-0636 ... For PTR05-0336, 36T PulleyPTR05-1632 ... For PTR05-1332, 32T PulleyPTR05-1638 ... For PTR05-1338, 38T PulleyPTR05-1640 ... For PTR05-1340, 40T PulleyPTR05-1644 ... For PTR05-1344, Each Doug Wesler
3632007-08 DRAG RACING PARTS AND ACCESSORIES
Big Block Chevy Oil Pump Drive Kit PTR05-1150Big block Chevy drag race High
Torque Drive (HTD) Kit drives oil pump at 57% of crank speed and is designed for use with an electric water pump. Compatible with crank trigger ignitions. A 1.830" long mandrel/hub assembly, crank and oil pump pulleys, drive belt, pulley guides and hardware are included.
Oil Pump Drive MandrelsStress proof steel Mandrels deliver dependability that
racers demand. Mandrel lengths are measured on the 1" O.D. portion of the mandrel.
Steel Part No. Aluminum Part No. DescriptionSmall Block Chevrolet
Big Block ChevroletPTR05-0712 – 1.830" LongPTR05-0713 – 2.760" LongPTR05-0714 – 5.000" Long
Mandrel Bolts Grade 8 Bolts for use with Peterson
mandrels. L-9 washers are included.Part No. DescriptionPTR05-0751 ...7/16"-20 x 3-1/2", Use With PTR05-0701 MandrelPTR05-0752 ...7/16"-20 x 5", Use With PTR05-0702 MandrelPTR05-0753 ...7/16"-20 x 6", Use With PTR05-0703 MandrelPTR05-0754 ...7/16"-20 x 8", Use With PTR05-0704 MandrelPTR05-0763 ...1/2"-20 X 4-1/2", Use With PTR05-0713 MandrelPTR05-0764 ...1/2"-20 X 6", Use With PTR05-0714 Mandrel
Drive Pulley Guide And Step WashersPeterson Drive Pulley Guide and Step Washers are
machined from 6061-T6 aluminum and are a must for proper belt alignment.Part No. DescriptionPTR05-0730 ...Step Washer, 2 1/2" O.D. With 7/16" Bolt HolePTR05-0731 ...Step Washer, 2 1/2" O.D. With 1/2" Bolt HolePTR05-0732 ...Step Washer, 2 1/2" O.D. With 5/8" Bolt HolePTR05-0735 ...Guide Washer, 2 1/2" O.D. With 1" I.D. Hole, .125" ThickPTR05-0736 ...Guide Washer, 3" O.D. With 1" I.D. Hole, .125" ThickPTR05-0737 ...Guide Washer, 3-1/2" O.D. With 1" I.D. Hole, .125" Thick
Mandrel SpacersPeterson Mandrel Spacers
are available in thicknesses from .250" to 1.250" and properly space/align the mandrel pulley pack. Spac-ers are machined from 6061-T6 aluminum and can be easily modified to accommodate non-standard sizes.Part No. Description Part No. DescriptionPTR05-0740 ...0.250" Thick PTR05-0743 ... 0.750" ThickPTR05-0741 ...0.375" Thick PTR05-0744 ... 1.000" ThickPTR05-0742 ...0.500" Thick PTR05-0746 ... 1.250" Thick
Scavenge FiltersPeterson’s billet aluminum
Inline Filters remove harm-ful debris from the oil before it reaches the pump. The free-flowing units have twice the filter area of dry sump pan screens.Part No. DescriptionInline Scavenge FiltersPTR09-0401 ... -8AN, Use On Lifter Valley Scavenge Or With Rear End PumpsPTR09-0402 ... -10AN, Use With Dry Sump Pan Or Lifter Valley Scavenge LinesPTR09-0403 ... -12AN, Use With Dry Sump Pan LinesInline 90° Scavenge FiltersPTR09-0406 ... -8AN, Use On Lifter Valley Scavenge Or With Rear End PumpsPTR09-0407 ... -10AN, Use With Dry Sump Pan Or Lifter Valley Scavenge LinesPTR09-0408 ... -12AN, Use On Dry Sump PanReplacement ScreensPTR09-0410 ... Fits PTR09-0402, PTR09-0403, PTR09-0407, PTR09-0408PTR09-0411 ... Fits PTR09-0401, PTR09-0406
Dry Sump Pan FiltersFilter bolts to pan fittings to protect pump from metallic
particles in the oil. Screen can easily be inspected with-out removing pan. 2-1/4" long body.Part No. DescriptionPTR09-0404 ... Filter With -12AN FittingPTR09-0411 ...Replacement ScreenEAR935112 ....Earl’s -12AN, 90° Female Fitting
Provides Extra Clearance When Mounting PTR09-0404
400 Series Inline Oil FiltersInline Oil Filters have 25% more filter area than similar
units and are available in 60 and 75 micron configura-tions for engine oil. 2-1/2" filter bodies are hard anod-ized. Filter mounting brackets are sold separately.Part No. DescriptionInline Oil FiltersPTR09-0438 ... -12AN Filter, 75 Micron ElementPTR09-0439 ... -16AN Filter, 75 Micron ElementPTR09-0457 ... -10AN Filter, 60 Micron ElementPTR09-0458 ... -12AN Filter, 60 Micron ElementFilter Mounting BracketsPTR09-0492 ... Fits 1-1/2" Dia. TubingPTR09-0493 ... Fits 1-3/4" Dia. TubingPTR09-0494 ... Firewall MountReplacement ElementPTR09-0440 ...75 Micron, Fits -8, -10, -12, -16AN FiltersPTR09-0460 ...60 Micron, Fits -8, -10, -12, -16AN Filters
Mike Blof
364 2007-08 DRAG RACING PARTS AND ACCESSORIES
Drag Race Dry Sump Oil TankTwo-piece, 1-1/2 gallon Tank is 7" in di-
ameter. Tank includes a single return, two -12AN male fittings for an external catch can, a bung for an immersion oil heater and a billet cap. Tank has been tested and proven by Pro Stock racers Warren and Kurt Johnson to deliver exceptional oil con-trol with absolutely no blowing. Mounting brackets must be purchased separately. Part No. DescriptionPTR08-0783 ...1.5 Gallon Dry Sump Oil TankPTR08-0102 ...Mounting Brackets For 7" Dia. Tank, Pair
have internal baffling to aerate the scav-enge oil and maintain a tall oil column over the pickup. Tanks are easily disas-sembled and tops can be rotated to ease plumbing. Mounting brackets must be purchased separately.Part No. DescriptionPTR08-0004 ...1.5 Gallon Tank, Dual Scavenge Inlet,
15-1/2" High x 6" Dia.PTR08-0005 ...2 Gallon Tank, Single Scavenge Inlet,
19-1/2" High x 6" Dia.PTR08-0100 ...Mounting Brackets For 6" Dia. Tank, PairPTR08-0110 ...Replacement O-Ring, 6" Dia. Tank
Dry Sump Tank FittingsAnodized aluminum Fittings complete the
installation of any Peterson dry sump tank.Part No. DescriptionPTR08-0501 ... -10AN Hose x -12AN PortPTR08-0502 ... -12AN Hose x -12AN PortPTR08-0503 ... -16AN Hose x -12AN PortPTR08-0504 ... -6AN Port Plug (Tank Drain)PTR08-0505 ... -12AN Port Plug (Tank Drain)PTR08-0506 ...O-Ring Kit, -12AN (5 Per Pack)
Oil Tank HeatersPreheating oil en-
sures lubrication on initial start-up and increases horsepow-er. Immersion-style Heater only requires welding a threaded bung into the tank. Wrap around styles can be glued to the outside of the tank or pan.Part No. DescriptionPTR08-0300 ...300 Watt Immersion Style,
110 Volt With Detachable Cord Set, Steel And Aluminum 1/2"NPT Weld Bungs
PTR08-0301 ...300 Watt Wrap Around Pad, 2" x 15", 110 Volt With Detachable Cord Set, Attaches With Hi-Temp RTV Silicone
PTR08-0302 ...400 Watt Wrap Around Pad, 4" x 10", 110 Volt With Detachable Cord Set, Attaches With Hi-Temp RTV Silicone
Remote Breather Can PTR08-0400Spun aluminum Can may be used with
any dry sump tank and includes two -12AN female ports and one -6AN drain plug. Pur-chase fittings separately.
Screw-In Breather PTR08-0415Internally baffled Breather has -12AN male
threads to fit bung on Peterson dry sump tanks. May also be used on valve covers.
In-Line Temp Port AssemblyIn-line Temperature Port Assembly has
a standard 5/8"-18 threaded port for a temperature probe.Part No. DescriptionPTR09-1940 ... -10AN Nose x -10AN NosePTR09-1960 ... -12AN Nose x -12AN Nose
Regulator regulates crankcase vacuum, which helps maximize ring seal and engine performance. Adjustable from 2 to 29.7 in/hg.
One Way Valve Pop Off PTR08-0450Breather Assembly is installed in valve cover
on engines running crankcase in vacuum condition. Valve seals the engine from air entering, but opens in the event of crankcase pressure, allowing crankcase to vent. Includes -12AN bung to weld to aluminum valve cover.
lows oil pressure to be adjusted on applications where rules require the oil pump be in the stock location. May also be used with a dry sump to make the pressure regulator more accessible.Part No. DescriptionPTR09-0160 ...Remote Relief Valve, -10AN FittingsPTR09-0161 ...Remote Relief Valve, -12AN Oil Fittings, -10AN Relief Line Fitting
raises the oil pressure line connection for easier access. Fittings are 1/8"NPT on engine side and -4AN for gauge connection.
3652007-08 DRAG RACING PARTS AND ACCESSORIES
Oil Filter Block Off PlatesOil Filter Block Off Plates facilitate the installation of wet
and dry sump oil pressure lines to the stock oil filter pad. Plates are made from billet aluminum and include mounting hardware.Part No. DescriptionPTR09-0002 ...Chevy V8 With -12AN fittingPTR09-0004 ...Chevy Bow Tie Block With -12AN fittingPTR09-0011 ... Ford V8 With -12AN fittingPTR09-0020 ...Replacement Square O-ring For PTR09-0001 Thru PTR09-0004
Large Diameter Remote Filter MountRemote Filter Mount is CNC machined from 6061-T6
billet aluminum for strength and light weight. Mount has two inlet and two outlet ports which are -12AN. Mounts include two AN adapter fittings and two solid plugs. Used with Fram HP6 filter.Part No. Description1-1/2"-12 Filter MountsPTR09-0530 ... -10AN FittingsPTR09-0531 ... -12AN FittingsAccessory PartsPTR08-0501 ... -10AN x -12 Port FittingPTR08-0502 ... -12AN x -12 Port FittingPTR08-0505 ... -12AN Port Plug - SolidPTR15-1010 ... -12AN Port Plug x 5/8"-18 Temp. Port
assure maximum vacuum levels for engines with dry sump oil systems. Seals are manufactured by TKO Competition Development.Part No. DescriptionPTRSM86410 ......... Rear Main Seal, SB Chevy 400PTRSM86586 ......... Jesel Front Cover, Chevy Cam SealPTRSM86587 ......... Jesel Front Cover, SB Chevy Crank SealPTRSM86622 ......... Jesel Front Cover, BB Chevy Crank SealPTRSM86625 ......... Rear Main Seal, SB Chevy 350PTRSM86990 ......... Front Crank Seal, SB Chevy
SB Chevy Manifold End Rail SpacersFill the gap between the manifold and the lifter valley
end rails when using raised port cylinder heads on small block Chevy engines. Sold in pairs, Spacers include four 3/16" roll pins for retention. Drilling of the block is re-quired for installation.Part No. DescriptionPTR09-1060 ........... Spacer Set, .125" ThickPTR09-1061 ........... Spacer Set, .187" ThickPTR09-1062 ........... Spacer Set, .250" Thick PTR09-1063 ........... Spacer Set, .375" Thick PTR09-1064 ........... Spacer Set, .500" Thick
Freeze Plug KitsSkin packaged cards contain all
freeze and pipe plugs necessary for a short block. Available in traditional steel or brass.Application Steel Part No. Brass Part No.SB Chevy 262-350 PIOPE100 PIOPE100BSB Chevy 400 PIOPE101 PIOPE101BBB Chevy 396-454 PIOPE102 PIOPE102BSB Chrysler 273-360 PIOPE113 PIOPE113BBB Chrysler 383-440 PIOPE114 PIOPE114BSB Ford 289-351W PIOPE108 PIOPE108BFord 351C, 351M-400 PIOPE109 PIOPE109BBB Ford 390-428 “FE” PIOPE110 PIOPE110BBB Ford 429-460 PIOPE125 PIOPE125BOldsmobile 260-455 PIOPE124 PIOPE124BPontiac 326-455 PIOPE115 PIOPE115B
Cylinder Head Dowel Pin KitsEach Kit includes four Dowel Pins.
Part No. DescriptionPIOS-1110 ......SB Chevy 265-400PIOS-1111 ......BB Chevy 396-454PIOS-1112 ......SB Ford 221-351W
Aerosol Engine EnamelsEngine Enamels dry
quickly to a tough, durable finish resistant to blistering and peel-ing. Choose from a variety of colors.Part No. Description Part No. DescriptionPIOT-10-A ...Chevy Orange PIOT-54-A ...Flat BlackPIOT-11-A ...Ford Blue PIOT-55-A ...Gloss WhitePIOT-12-A ...Ford Red PIOT-56-A ...High Heat BlackPIOT-14-A ...Chrysler Red PIOT-58-A ...Cast Iron GrayPIOT-16-A ...Ford Green PIOT-58-A ...Cast Iron GrayPIOT-17-A ...Ford Dark Blue PIOT-59-A ...ClearPIOT-18-A ...Ford Antique Green PIOT-60-A ...Universal GrayPIOT-19-A ...Chevy Blue PIOT-61-A ...Lo-Gloss BlackPIOT-26-A ...Universal Black PIOT-62-A ...High Heat AluminumPIOT-27-A ...Aluminum PIOT-63-A ...High Heat Cast Iron GrayPIOT-37-A ...Gloss Gray PIOT-64-A ...Black PrimerPIOT-50-A ...Light Gray Primer PIOT-65-A ...Stainless SteelPIOT-52-A ...Red Oxide Primer
Ground Shipment
Only
366 2007-08 DRAG RACING PARTS AND ACCESSORIES
Trailer Door CabinetsNo trailer should be without Pit
Pal’s handy Trailer Door Cabinets. Heli-arc welded from .090" alumi-num for long term strength and durability, each cabinet has a paper towel holder, a fold-down table for added work space, and enough shelving to hold aerosol cans, oil containers, cleaners, etc.Part No. DescriptionPIT320 ..... Door Cabinet 30" H. x 25" W. x 5.5" D.PIT321 ..... Jr. Door Cabinet 19.5" H. x 12" W. x 4.5" D.
Oil Storage CabinetsRugged Oil Storage Cabinets,
made of .090" thick aluminum, are available in two sizes. Large cabi-net will store 29 quart bottles and eight aerosol cans. Junior cabinet holds 12 bottles.Part No. DescriptionPIT310 ..... Oil Storage Cabinet,
36" H. x 24-1/2" W. x 5-1/2" D.PIT313 ..... Junior Oil Storage Cabinet,
18" H. x 16" W. x 5-1/2" D.
Aerosol Spray Can ShelvesStrong .090
aluminum Shelves fit anywhere for conveniencePart No. DescriptionPIT100 ..... 8 Can, 21" LongPIT101 ..... 12 Can, 32-1/2" Long
Paper Towel Holder PIT226Provide easy access and storage
of paper towels.
Helmet ShelvesStore helmet, neck brace,
gloves, ear protectors and related items. Hang up to eight uniforms beneath shelf. Shelves are fabricated from .090" alumi-num for maximum strength.Part No. DescriptionPIT330 ..... 1 Bay Helmet Shelf, 14-1/2" L. x 12" H. x 15" W.PIT331 ..... 2 Bay Helmet Shelf, 28-1/2" L. x 12" H. x 15" W.PIT332 ..... 3 Bay Helmet Shelf, 42-3/4" L. x 12" H. x 15" W. New!
D Cell Flashlight Holder PIT216Handy, .090" thick aluminum Holder secures any
“D” cell flashlight to tool boxes, trailer walls, etc.
Gauge Pouch PIT228Secures tire gauges up to 3-3/4" dia.
cures as many as six 10 lb. nitrous oxide bottles. Rack, which is 13" H. x 7-1/4" D. x 44-1/2" W., is easily attached to floor or wall.
Trailer Fuel Jug RacksHeli-arc welded .090"
aluminum racks mount easily on trailer floor or wall to hold round or square fuel jugs safely and securely.Part No. DescriptionPIT180 ..... 1 Jug Rack, 11-1/2" L. x 12" D. x 14" H.PIT181 ..... 2 Jug Rack, 23" L. x 12" D. x 14" H.PIT182 ..... 3 Jug Rack, 34-1/2" L. x 12" D. x 14" H.PIT183 ..... 4 Jug Rack, 46" L. x 12" D. x 14" H.
Multiple Strap Hanger PIT218Store tie downs and bungee cords
neatly. Wall mount bracket is 17" long.
Tie Down HangersBracket fastens to trailer wall
for storage of ratchet tie downs. Bracket is 8" long x 3" deep and holds two tie downs. Sold individu-ally, or in pairs.Part No. DescriptionPIT217 ..... Single Tie Down Hanger BracketPIT222 ..... One Pair Tie Down Hanger Brackets
Hanging BracketsHanging Brackets store all hoses
and electrical cords neatly. Give shop or trailer a professional look.Part No. DescriptionPIT220 ..... Electrical Cord BracketPIT221 ..... Air Hose Bracket
Deluxe Air Bracket PIT223Great for storing air chuck, air
gauge, small tools, etc.
Universal Hanger PIT170Keep helmet, driving jacket and gear
handy. Hanger is 3-1/2" wide x 4" high x 2-1/2" deep.
PIT220
PIT217
PIT183
PIT330
PIT310
PIT320
PIT101
Gauge Not Included
3672007-08 DRAG RACING PARTS AND ACCESSORIES
Aluminum Work TablesAluminum Work Tables with
tubular locking fold-in legs may be set up or knocked down quickly and are strong enough to hold heavy engine, transmission or rear end parts. Use anywhere.Part No. DescriptionPIT155 ............ Large Work Table, 31" W. x 72" L.PIT156 ............Standard Work Table, 25" W. x 42" L.
Junior Universal Tool TraysSturdy low profile Trays are 16-1/2"
wide x 5" high x 13-1/4" deep and great for working on cars with hoods. Choice of standard or Dominator carburetor ring.Part No. DescriptionPIT129-D ........ Junior Tool Tray, Dominator
Carb RingPIT129-S ........ Junior Tool Tray, Std. Carb Ring
Flip Down TraysHandy, aluminum Trays provide
extra work space and fold and latch when not in use. Available in two sizes.Part No. DescriptionPIT151 ............ Jr. Flip Down Tray, 13" W. x 6-1/2" D.PIT152 ............ Flip Down Tray, 30" W. x 16" H. x 3" D.
Canopy Holder PIT195Secures 10' x 10' or 10' x 20'
canopy or pop-up tent to trailer or garage wall. Includes two brackets and a pair of 1-1/2" wide safety belts.
E-Track PITETH-1An ideal horizontal
attachment point on floors, walls or ceilings. Zinc plated steel E-Track is 5' long.
Track Strap PIT074118Track Strap, is 2" wide x 6" long with a 1,000
lb. rating. Typically used with Pit Pal’s E-Track or A-Track to adapt as a tie down hanger.
Jack In A Pouch PIT194Wall mounted Pouch keeps pit jack
contained during transport, and adds floor space. TIG-welded aluminum, .090" thick pouch is 17-1/2" wide x 24-1/4" high x 5-1/8" deep.
Floor Jack Mounts PIT190Floor Jack Mounts keep jack
secure for the long haul. Drop jack in between angles and posi-tion front wheels in semi-circular front shells. The jack will remain in place during sudden stops, starts and tight corners.
Pit Bike Chock PIT270Easily mounted
to secure most scooters. Fits up to 15" dia., 5" wide tires.
Slick Mounts PIT282Black powder coated, 14 gauge
telescoping mount is made of 1-1/2" x 46" long steel tubing and accepts nearly any tire and wheel combination. Includes .125" steel round clamping plates.
Dual Extension RampsHelpful when loading or unloading
low-slung race cars. Ramps are 14" wide, and fabricated from .125" thick aluminum with tig-welded reinforcing ribs, heavy hinges and rivets. Flips up for easy transportation. Sold in pairs.Part No. DescriptionPIT699 ............14" Wide x 36" LongPIT702 ............14" Wide x 72" Long
Trailer Door BumpersPrevents trailer door damage. May be
used to adjust entrance angle to accom-modate extension ramp.Part No. DescriptionPIT703 ............7-3/4" Long x 2" High x 2-7/16" WidePIT704 ............6" Long x 3-1/4" High x 2-7/8" Wide
Jack Not Included
PIT703
PIT282
Steve Rutgers The Carson Twins
368 2007-08 DRAG RACING PARTS AND ACCESSORIES
SFI-Approved Harmonic BalancersPowerbond Balancers are available in traditional and new “Extreme” versions. On traditional units, the crank hub is
bonded to the outer ring with durable rubber to prevent the outer ring from spinning or separating. “Extreme” balanc-ers are made for high RPM racing with forged hubs, heavier inertia rings and temperature resistant elastomers for improved dampening, longevity and performance. Balancers meet SFI 18.1 specifications.
Standard Part No.
New! “Extreme” Part No. Application Dia. Wt. Balance
* Requires crank flange (PBBFHL1481-SS for Caprice/Impala or PBBFHS1481-SS for Camaro/Firebird.** May only be used on externally balanced 460 with factory winged counterweights.
Pro Head CC KitsBuret Kits include everything
needed to CC combustion cham-bers, and intake and exhaust runners. Glass burets are com-patible with alcohol, parts washer solvent, or any other suitable fluid and are marked off in .2cc incre-ments for easy reading.Part No. DescriptionPOW351140 ...125cc X .2ccPOW351150 ...100cc X .2cc
Rimac Spring Tester POW360070The Rimac Bench Top Spring Tester has been
the industry standard for over 70 years and is the only sure way to check spring height versus spring pressure. Capably handles valve, trans-mission, clutch and other springs up to 2" dia. and 4-1/2" free length. Calibrated test spring enables testing and recalibrating in the field. Measures 0-1000 lb. x 5 lb.
Pro Piston Knocker POW101290Non-marring Piston Knocker is 13" long with
2" and 2-1/2" diameter ends. Tool is loaded with steel shot to provide a dead blow effect from its 2 lb. weight for effortless hammer blows when installing pistons.
Cartridge RollsResin-bonded sanding Rolls will finish port and polish
work. Rolls are 3/8" dia. by 1-1/2" long and fit 1/4" mandrels. 50 per package.Part No. DescriptionPOW351476 ...40 GritPOW351480 ...60 GritPOW351485 ...80 GritPOW351490 ...100 GritPOW351495 ...120 Grit
Porting MandrelsPorting Mandrels are for use with
the above 1/4" dia. cartridge rolls. Available in lengths from 4" to 8". Part No. DescriptionPOW351504 ...4"lPOW351506 ...6"POW351508 ...8"
