+ All Categories
Home > Documents > DRUM HANDLING EQUIPMENT 350kg Heavy-duty Drum Trucks … · 2017-06-08 · DL70 Drum Lifter (right)...

DRUM HANDLING EQUIPMENT 350kg Heavy-duty Drum Trucks … · 2017-06-08 · DL70 Drum Lifter (right)...

Date post: 23-Jun-2020
Category:
Upload: others
View: 10 times
Download: 0 times
Share this document with a friend
7
DRUM HANDLING EQUIPMENT 54 SPECIALS CAN BE MADE TO SUIT CUSTOMERS’ UNIQUE REQUIREMENTS MODEL SUITABLE FOR WHEELS CAPACITY DTZ80 Rough Terrain Steel-centred 426mm pneumatic 350kg DTFBSR Industrial Steel-centred 250mm pneumatic 350kg DTWHBB Industrial & Yard Steel-centred 250mm solid rubber 350kg DTBWBB Drum Cradle 400mm plastic-centred pneumatic 350kg Strong steel construction, Zinc Plated protection. Heavy sliding catch engages over drum lip. Wheel choices (as pictured). 100mm nylon jockey wheels allow maximum stability when drums are loaded or unloaded. DR64 TRIANGULAR CASTORS: 75mm nyl. swivel CAPACITY: 300kg SIZE: 500m DDSQ SQUARE CASTORS: 75mm nyl. swivel CAPACITY: 400kg SIZE: 600mm x 600mm DR66 SQUARE CASTORS: 75mm nyl. swivel CAPACITY: 400kg SIZE 600mm x 600mm HEIGHT: 125mm DDSQ Square Provides full mobility of drums throughout the factory. Heavy steel angle construction. For 200L steel drums. DR64 – Triangular Heavy steel flat bar construction. For 200L steel drums. Castors: 75mm nylon swivel. Capacity: 300kg Designed for handling low weight or low volume 60 or 200L steel drums. Strong steel construction with a zinc-plated finish for full protection. Sliding catch secures drum. Can also be used as a General Purpose Hand Truck. Wheel options: 300 x 4 pneumatic or 250mm solid rubber. DTC/T Plastic Drum Tie-down A strong webbing and ratchet tie-down is available as an optional extra for securing plastic drums to the Drum-truck. DTC DRUM TRUCK HEIGHT: 1200mm CAPACITY: 250kg LIP SIZE: 250mm x 360mm DR66 Square General purpose. Welded angle steel with 18mm customwood deck. Heavy-duty Drum Trucks for 200/220L Drums • Welded steel construction with zinc-plated finish for maximum corrosion resistance • A range of wheel options – pneumatic or solid rubber • Attachment for plastic drums an optional extra for each model Up to 350kg capacity DTZ80 Rough Terrain Negotiate gravel surfaces, floor grates etc. Wheels: 426mm pneumatic. 100mm nylon jockey. DTFBSR Industrial Use on multi surfaces. Wheels: 250mm pneumatic. 100mm nylon jockey. DTWHBB Industrial & Yard For smooth surfaces. Wheels: 250mm Solid Rubber-tyred DTBWBB Drum Cradle Chain secures the drum. Fixed stand to lay horizontally. Wheels: 400mm pneumatic. DTC SPECIAL PURPOSE HAND- TRUCKS Pg 51–53 Combination Drum Truck Drum Dollies
Transcript

DRUM HANDLING EQUIPMENT

54SPECIALS CAN BE MADE TO SUIT CUSTOMERS’ UNIQUE REQUIREMENTS

MODEL SUITABLE FOR WHEELS CAPACITY

DTZ80 Rough Terrain Steel-centred 426mm pneumatic 350kg

DTFBSR Industrial Steel-centred 250mm pneumatic 350kg

DTWHBB Industrial & Yard Steel-centred 250mm solid rubber 350kg

DTBWBB Drum Cradle 400mm plastic-centred pneumatic 350kg

Strong steel construction, Zinc Plated protection. Heavy sliding catch engages over drum lip. Wheel choices (as pictured). 100mm nylon jockey wheels allow maximum stability when drums are loaded or unloaded.

DR64 TRIANGULAR

CASTORS: 75mm nyl. swivel

CAPACITY: 300kg

SIZE: 500m

DDSQ SQUARE

CASTORS: 75mm nyl. swivel

CAPACITY: 400kg

SIZE: 600mm x 600mm

DR66 SQUARE

CASTORS: 75mm nyl. swivel

CAPACITY: 400kg

SIZE 600mm x 600mm

HEIGHT: 125mm

DDSQ

SquareProvides full mobility of drums throughout the factory.

Heavy steel angle construction.

For 200L steel drums.

DR64 – TriangularHeavy steel flat bar construction.

For 200L steel drums.

Castors: 75mm nylon swivel.

Capacity: 300kg

Designed for handling low weight or low volume 60 or 200L steel drums. Strong steel construction with a zinc-plated finish for full protection. Sliding catch secures drum.

Can also be used as a General Purpose Hand Truck.

Wheel options:300 x 4 pneumatic or250mm solid rubber.

DTC/TPlastic Drum Tie-downA strong webbing and ratchet tie-down is available as an optional extra for securing plastic drums to the Drum-truck.

DTC DRUM TRUCK

HEIGHT: 1200mm

CAPACITY: 250kg

LIP SIZE: 250mm x 360mm

DR66 SquareGeneral purpose. Welded angle steel with 18mm customwood deck.

Heavy-duty Drum Trucks for 200/220L Drums• Welded steel construction with zinc-plated

finish for maximum corrosion resistance

• A range of wheel options – pneumatic or solid rubber

• Attachment for plastic drums an optional extra for each model

Up to 350kg capacity

DTZ80 Rough TerrainNegotiate gravel surfaces, floor grates etc.Wheels: 426mm pneumatic. 100mm nylon jockey.

DTFBSR IndustrialUse on multi surfaces.Wheels: 250mm pneumatic. 100mm nylon jockey.

DTWHBBIndustrial & YardFor smooth surfaces.Wheels: 250mm Solid Rubber-tyred

DTBWBB Drum CradleChain secures the drum.

Fixed stand to lay horizontally. Wheels:400mm pneumatic.

DTC

SPECIALPURPOSEHAND-

TRUCKSPg 51–53

Combination Drum Truck Drum Dollies

55

DRUM HANDLING EQUIPMENT

DC1 Drum CradleIdeal for 200L steel drums. Telescopic

handles with sliding catches which engage the drum lip. Rock back onto wheels to tilt drum horizontially to transport or decant.

DC1 DRUM CRADLE

SIZE: 930mm Long (handles in) Add 560mm with handles out 500mmW x 510mmH

WHEELS: 100mm black polypropylene

FOR DRUM PUMPS & TAPS SEE PAGE 58 – 59

Drum Tipping Cradles

DC4 Drum CradleFor 200L steel drums or 220L plastic drums. Position flat-bar lip under lower lip of drum and pull back to tilt horizontally to transport or decant.

Fit attachment DC4R (right) to freely rotate (steel) drums when resting horizontially.

DC4RDrum Revolving

Attachment

DC4 DRUM CRADLE

SIZE: 900mmL (including lip) 550mmW x 480mmH

WHEELS: 100mm black polypropylene

DC4R DRUM REVOLVING ATTACHMENT

SIZE: 590mmL x 480mmW

WHEELS: 75mm black nylon

Zinc-plated protection

Capacity: 250kgLength: 1120mm

DU Drum Upender

DLS Drum Lifting Sling DLCDrum Lifting

Clamp – Elephant

Lift drums vertically, horizontally or invert and

dump contents. Self locking jaws. Use with overhead hoist.

Capacity: 1000kg

DT Drum TongsLift drums horizontally using overhead hoist. Semi-automatic. Use with a forklift truck or overhead hoist.

DL70Drum Lifter (right)

Attach to 200 litre drums and use lifting hook/overhead hoist.

DTUDrum Tilting Unit (far left)

Two models – standard DTU for use with an overhead hoist, and a model with forklift pockets.

Drums rotate freely on axis.Optional locking device available.Ratchet secures drum.

DWSDrum Webbing Sling (left)

For 60L & 200L steel drums and a number of plastic drums.Ratchet secures drum.

• Welded steel construction with zinc-plated finish for maximum corrosion resistance

• Designed for 200L steel drums with plastic drum options.

Up to 250kg capacity

Drum Tipping Cradles

Our specialised Drum Handling Equipment is designed and built to provide

safe and efficient handling of heavy and awkward drums of all types. They’re

constructed from high quality steel and are very strong and robust.

General Drum Handling

Lift drums vertically, horizontally, or angled to discharge contents. Use with a forklift truck or overhead hoist.

DTU DWS

DL70

Drum Cradles

DRUM HANDLING EQUIPMENT

56

FDTU Forklift Drum Tilter

Easily slide on to forks. Drums rotate freely on axis with optional locking device available. Ratchet and chain secures drum.

Capacity: 360kg

Maximum fork section: 135 x 50mm

ADC1 Auto Drum Clamp

Easily slide on to forks.Suitable for standard steel 200L drums.

Also available:

ADC2 Double Drum

Capacity: 360kg

Maximum fork section: 180 x 50mm

Forklift Attachments – Drum Grips & Clamps • Heavy, welded steel construction

• Designed to handle 200L steel drums

Up to 680kg capacity

DG360A Single

DG360B Double

AUTO PARROT BEAK GRIP

Suitable for standard steel 200L and 60L drums – also Mauser L-ring drums, CHH plastic drums and Fibreboard drums.

Capacity: 360kg

Max. fork section: 135 x 50mm

HDT25B Hydraulic Drum Truck

STRADDLE LEG

The claw grabs the drum lip – hydraulic pump raises drum to desired height. Move easily on large roller wheels and easy steering rear braked castor.

Capacity: 250kg. Lifting height: 345mm

FLB150 Forklift Drum Carrier

Manipulate Drum from the Forklift. Suitable for standard steel 200L drums, also Mauser L ring, and some plastic drums. Ratchet and chain secures drum.

Capacity: 680kg

Maximum fork section: 170 x 50mm

EASYSLIP-ON

TYPE

ASK US ABOUTOTHER MODELS

OF FORKLIFT ATTACHMENTS

MK80 Mobile Drum Carrier

Tighten the chain lever to secure drum to the collar. Lift and tilt to decant a full drum. 2 large roller wheels with easy steering rear castor

Capacity: 360kg

Drum Lifting Trucks

57

DRUM HANDLING EQUIPMENT

• Maximum capacity 2500kg at extension position 1.

• Welded steel construction, fully zinc-plated for maximum corrosion resistance

Up to 2500kg capacity

Forklift Attachments – Fixed Jib and Bin Tipper

M16Coupler S/S

Drum Mixing EquipmentMixing blades are specially designed for bung-hole entry mixing in 60 & 200L drums. The stainless steel blades are lightweight and portable for speed and efficiency and set-up is simple. The mixers can be driven with a 1/2” electric drill or explosion-proof air drive motor (as pictured). Thick or cold fluids can be thinned by heating (see Drum Heater) for quicker mixing and dispensing.

The Fixed Jib provides an additional lifting height with the extension beam being raised above the fork pockets. Secured to the forklift by safety chains, the overall length when retracted is 1.3m, and when extended is 2m.

Fixed Jib Attachment – Short. 2.5 tonne

FJCS25 FIXED JIB ATTACHMENT

CAPACITY: 2500kg Maximum

FORK POCKETS: 185mm x 65mm

UNIT WEIGHT: 100kg

With two models available, one

for 240L and another for 660L

wheelie bins, the WB style tipper

is operated from the forklift

drivers seat by a pull-cord. The bin

is secured in the bin cradle with

safety chains.

• Enamel paint finish

• 500kg capacity

SAFE WORKING LOAD (SWL) PER POSITION:

POSITON: 1 2 3 4

EXTENSION: 790 1200 1580 1960

SWL: 2500kg 1200kg 900kg 750kg

FORK LOAD UNITMODEL CAPACITY POCKETS CENTRES WEIGHT

WB-240 500kg 165 x 65mm 1000mm 100kg

WB-660 500kg 165 x 65mm 1700kg 140kgWB-660

FJCS25

Wheelie Bin Tipper

WB-240

240L & 660LMODELS

Drum Heating Collar

DHB/T Drum Heater

(200/220L steel drums only)

For heating, melting and thawing non-volatile liquids, solids and viscous materials such as greases, fats, gelatine, tar and heavy oil.

Heater is non-flameproof for operation on 230 volt AC mains. Maximum 2000W with thermostat control (supplied without input lead). Standard temperature range 30º–110º, special 0º–40º.

200L DRUM:

M02 Mixer

M16 Coupler

M07 Motor Stand

M14 Air Drive Motor (300 - 3000rpm)

60L DRUM :

M19 Mixer

M24 Coupler

M07 Motor Stand

M14 Air Drive Motor (300 - 3000rpm)

USUAL REQUIREMENTS

BUNG ENTRY (2”BSP)

ELECTRIC DRILL OPERATION

Variable speed drill – 1/2” chuck or larger.

200L DRUM: M02 Mixer

60L DRUM: M19 Mixer

M07Motor StandGalvanised

M02 Mixing Blade 5-blade, Stainless Steel

M14Air Drive Motor

DRUM HANDLING EQUIPMENT

58

Drum Pumps

Rocker Galley Pump

• Fresh or salt water

• 13 strokes per litre

Ultra Pantry Pump• Quality plastic

pump

• Vertical plunger action

Bung SpannerDBS3 430mm

For removing bungs from steel or plastic

drums. Fits most types of drum closure.

Diaphragm Hand Pump

• Self-priming

IMPORTANT: Advise specific chemical applications to ensure correct usage. Always wear protective clothing and eye protection when dispensing chemicals. Don’t mix applications; ie. one pump per fluid type.

Rotary PumpTQ14

Cast alloy body with steel inlet/outlet tubing and heavy-duty

handle. Delivers up to18 litres per minute. Transfer fluids

in both directions. Ideal for transferring petrol, diesel fuels,

heavy oil, machine oil, low viscosity oils and non-corrosive

liquids. Includes 2.2m farm tank grade anti-static hose.

Lever PumpTQ01General purpose, steel construction with three alternative

‘O’ rings and chemical compatibility chart. Telescopic suction

tube. Comes with 1.8m outlet hose (petrol resistant). Suitable

for a wide variety of chemicals and solvents. Convenient bung

opener cast on pump head. Pumps approx. 250ml per stroke,

and handles liquids to SAE90.

SigmaDouble-action Pump

• Cast-iron K model

• Suitable for clear and light fluids – water, petrol, diesel.

Drum Pump options designed for use with

two inch outlets on 200L and 60L standard

steel drums.

Suitable for 2” outlets

Hand Pumps – SUITABLE FOR BOATS, CARAVANS, MOTOR HOMES ETC.

Siphon PumpTQ05

Polyethylene construction.

Siphons liquids from higher

to lower levels. Pumping

the bellows primes the

pump and begins siphon

action. Simply loosen vent

cap to stop the siphon flow.

Pump bellows to dispense

fluids to a higher level.

Siphons up to 20 litres per

minute, handles light oils,

kerosene and various types

of light solvents.

ClassicBrass Pump

• 10 strokes per litre

59

DRUM HANDLING EQUIPMENT

• Polyethylene, Polypropylene, Brass and Stainless Steel

• Lever and screw-action models

2” and 3/4”Drum Taps

TP01 Polyethylene

Flo-king. lever action 2” NPS

TP08 Polyethylene LLDPE Lever action. 3/4” BSP

TP14 Polyethylene HDPE Front lever action. 3/4” BSP

TP09 Polyethylene HDPE Screw action. 3/4” BSP

TP04 Ball valveNickel plated, brass body, chrome plated ball, Teflon seals. Male/Female, 3/4” BSP

TP18 Brass SPRING LOADED.Self-closing, Teflon seal.Fire baffle 3/4” BSP

Special Purpose Taps

TP15/58 PolyethyleneLLDPE. Aeroflow with 58mm cap for Plastic Industry and Rheem containers.

TP15/70LLDPE. Aeroflow with 70mm cap for Carter Holt Harvey containers.

TP22 StainlessBall Valve (316)3 Piece. Teflon seal F-F 2” BSP. Serviceable in-situ

TP21 – 2 Piece. Teflon seal

F-F 2” BSP. Seal serviceable

TP20 – 1 Piece. Teflon seal F-F 2” BSP. (1” through body). Non-serviceable

TP22 with optional nipple and elbow

2” Drum Taps

TPB01 2” BSP external / 3/4” BSP internal

TPB02 2” Mauser external / 3/4” BSP internal

TPB03 2” Van Leer external / 3/4” BSP internal

TPB04 2” Rieke external / 3/4” BSP internal

TPB01 TPB02 TPB03 TPB04

TP02 Treacle Tap

Molasses Gate. Gunmetal, 2” BSP

TP02S Treacle Tap

Molasses Gate

Brass, spring loaded, Teflon seal, 2” BSP

KEY: BSP – British Standard Pipe Thread NPS – US National Pipe (straight) Thread HDPE – High Density Polyethylene LLDPE – Linear Low Density Polyethylene

TPA03 TPA01TPA06 TPA02

TPA01 2” Mauser external / 2” BSP internal short

TPA02 2” Rieke external / 2” BSP internal

TPA03 2” Van Leer external / 2” BSP internal

TPA06 IBC Shultz 60mm NW50 Butt Fem - 2” BSP

TP07 Polypylene HDPESPRING LOADED. Lever action. 3/4” BSP

3/4” Drum Taps

Bung Reducers – (HDPE)Drum Adaptors – Polyethylene (HDPE)

DRUM HANDLING EQUIPMENT

60

SL 1

Offering complete protection against damaging and costly chemical spills,

Spill Containment Bins are available for one, two and four 200 litre drums.

Close spacing support bars allow for large or small drums up to 2000kg to

be placed on the spill bin. All models have a spill capacity of at least 110%

containment of the largtest drum in accordance with Australian Standards,

being classified as ‘portable’ units, and have zinc-plated finish.

These drum racking options provide a cleaner

environment and a safer working area by

protecting against costly and dangerous spills.

The racking system consists of the bolt together

drum rack, and the spill containment tray which it

stands over. In the event of a spill, the tray can be

easily removed without disturbing the drum rack.

Each spill tray is fitted with a removable plug for

emptying.

Drum racking systems are fully zinc-plated

No. OF DIMENSIONS SPILL UNITMODEL DRUMS W x D x H CAPACITY WEIGHT

SL 1 1 810 x 760 x 490mm 240 litres 55kg

SL 2 2 1210 x 610 x 440mm 250 litres 60kg

SL 4 4 1210 x 1210 x 265mm 245 litres 70kg

SBP 4 4 1400 x 1400 x 270mm 245 litres 40kg

SL 4

SL 2

Drum Racking System

A NUMBER OF DRUM RACKING OPTIONS ARE AVAILABLE

RS2-2L

RS3-3LRS3L

RS2L

RS2L DRUM RACKING SYSTEM

WIDTH DEPTH HEIGHT

RACK: 1330mm 600mm 831mm

TRAY: 1210mm 1210mm 265mm

Stand alone Drum Rack bolts together. Tray sits below and is forkliftable without disturbing the rack.

FOR DRUM TAPS SEE PAGE 58 – 59

Drum Spill Containment Bins • One, two and four drum units available

• Spillage capacity is 110% containment

For 200L drums

SBP 4Plastic Spill PalletHolds up to four 200L drums. Drip and spill containment unit integrated with IBC bund. Worksafe compliant.


Recommended