Date post: | 15-Sep-2015 |
Category: |
Documents |
Upload: | jose-miguel-mansilla-barrera |
View: | 202 times |
Download: | 49 times |
XK3190-DS2
WEIGHING INDICATOR
MANUAL
PLEASE READ THIS MANUAL VERY CAREFULLY
BEFORE USE
FEB 2007
Specifications subject to change without prior notice
1
CONTENTS
1. GETTING STARTED
2. TECHNICAL PARAMETERS AND SPECIFICATIONS
3. LAYOUT OF INDICATOR
4. KEYBOARD AND METROLOGY OPERATION
5. MENU OPERATION
6. INPUT
7. CALIBRATION
8. COMMUNICATION
9. PRINT AND RECORD OPERATION
10. INTERFACE SET UP
11. INFORMATION INDICATION
12. MAINTENANCE AND WARNINGS
APPENDIX
1. GETTING STARTED
CAUTION
This is not a toy. Keep out of reach of children;
This indicator is not an explosion proof device;
This indicator is not a water proof device;
Do not open this indicator, no user serviceable parts inside.
Always contact supplier for service.
1.1 Introduction
Weighing indicator XK3190-DS2 adopts 32-bits fast speed and
high performance ARM processor and effectivemulti-tasks
embedded operating system. Hence its with convenient character
input and personal operating window. Its widely applied in
static weighing system equipped with 1~16 digital load cell.
1.2 Features
With 32--bits fast speed and high performance ARM
processor
With effectivemulti-tasks embedded operating system
With personal operating window
With planar rolling menu management
With plenty parameter setting clew
With error diagnose function
With Num/English character/Chinese character/sign
input method similar to mobile phone input
2
With shortcut recall for common information such as
vehicle NO. and cargo name
Able to connect with digital load cell(ect. HBM)
Auto/manual angle adjustment
Call and display inner code to replace weight observing
and analysis tolerance
Password management and timing power-off function
Able to setup print function for auto/manual; daily/sorted
statistics report printing
Able to setup print function for fast filled weighing bill
Weighing data save/check/delete/ protection in case of
power off
Standard RS232C /RS422/RS485 communication interface
with selectable baud rate
Standard scoreboard interface with 20mA current loop
method
Standard parallel print interface
Able to save 1000 vehicle ID and corresponding tare weight
1000 cargo ID and corresponding cargo name1000 weighing
records
2.TECHNICAL PARAMETERS AND SPECIFICATIONS
Model:XK3190-DS2
Digital load cell connection
-Connection method: RS422/RS485
-Connection distance: About 1000 meters
-Connection quantity:1~16
-Communication protocol of load cell: HBM, YAOHUA,or customized
-Load cell power: DC 12V,0.8A(Max)
Display
-Display method: VFD dot-matrix display(256*64)/LCD
dot-matrix display(240*60)
-Display range:000000~999999(without decimal point)
-Division:1/2/5/10/20/50
Keyboard
-Soft-touched rubber keyboard
-23 keys, 6 extended keys
Clock: real clock
Scoreboard interface
-Signal output method: serial
-Signal: 20mA current loop(constant current)
-Baud rate: 600
-Transfer distance: 2000 meters
Printer interface
-Method: With standard configuration of parallel printer
interface, able to connect with printer model LQ-300KKX-P1131
LQ-1600K
Serial communication interface
-Standard interface: RS232C/RS422/RS485
-Baud rate: 600/1200/2400/4800/9600, communication method
selectable
-Transfer distance: RS232C 30 meters; RS422/RS485 1200
meters
Power supply
-AC 110~220V;50~60HZ
3
-DC 24V
Operation temperature:0~40
Transportation temperature:-25~55
RH: 85RH
Housing
-Stainless steel housing, waterproof
-Size: 250mm*250mm*70mm (without bracket)
-Weight: 3.6KG
3. LAYOUT OF INDICATOR
3.1 Front view of the indicator
3.2 Back view of the indicator
3.3 Side view of the indicator
4
3.4 Window when powered on
Note: This window will appear when indicator is powered on or
when indicator gets no signal from load cell
3.5 Main window(weighing window)
Vehicle NO.: 10 character Cargo No.10 character Time
3.6 Main board description
A2006688 STELL 15:31:20
98765.43 kg
AUTO COMM INDER CODE STABLE NET ZERO
AC POWER
SUPPLY
LOAD CELL
CONNECTION
RS232/422/
485
PRINTER
INTERFACE
5
Note: After open back housing of the indicator, get power supply
cable, communication cable, printer cable through the
water-proof connector, and connect according to the hardware
configuration described in the following chapter.
4. Keyboard and metrology operation
4.1 Keyboard View
4.2 Key description
Key Description
[1/ABC Cargo No.] Setup for cargo no. at weighing mode;
123eric 1 or letter ABC at setup mode;
[2/DEF Vehicle No.] Setup for vehicle no. at weighing mode;
123eric 2 or letter DEF at setup mode;
[3/GHI SETUP] Enter into setup main menu at weighing
mode;
123eric 3 or letter GHI at setup mode;
[4/JKL SUP PRINT] Execute supply printing at weighing mode;
123eric 4 or letter JKL at setup mode;
[5/ MNO REP PRINT] Execute report printing at weighing mode;
123eric 5 or letter MNO at setup mode;
[6/PQR TARE PRESET] Setup for tare preset at weighing mode;
123eric 6 or letter PQR at setup mode;
[7/STU TOTAL PRINT] Execute total printing at weighing mode;
123eric 7 or letter STU at setup mode;
[8/ VWX SAVE PRINT] Execute save printing at weighing mode;
123eric 8 or letter VWX at setup mode;
[9/YZ CALIBRATE] Enter calibration setup at weighing mode;
123eric 9 or letter YZ at setup mode;
[0 BACKLIGHT] Open/Close backlight at non-setup mode;
123eric 0 at setup mode;
[TARE] Execute tare operation at weighing mode;
[ZERO] Execute zero operation at weighing mode;
[INPUT MODE] Switch between input mode at setup mode;
[CHECK] Enter into record checking window;
[INPUT] To input and save for parameter;
[WEIGH] To skip zero calibration while calibration
6
and directly to load calibration;
Directly to main window of weighing at
other setup mode;
[DELETE] Delete record or delete input value digit
by digit;
Enter into record delete menu at weighing
mode;
[ON/OFF] Power on or power off operation;
Press this key for 2~10 seconds to power off
indicator, or else it will execute reset
function;
[SAVE TARE] Enter into save tare window;
[] Direction key, menu or record page up;
[] Direction key, menu or record page down;
[] Direction key, back to former menu or enter
into menu bar at left;
Select left sign at PINYIN or SIGN input
mode;
[] Direction key, enter into next menu or
enter into menu bar at right;
Select right sign at PINYIN or SIGN input
mode;
[F1][F6] Extend function key, invalid currently;
4.3 Metrology operation
4.3.1 Power on and auto zero
A, After powered on, indicator display opening window and
initialize parameter, check communication setup. It enters into
weighing mode automatically. Indicator display error when load
cell connection is abnormal.
B, When power on, if weighs on platform deviates from zero point
but within auto zero range, indicator will perform auto zero.
4.3.2 Manually zero
A, Press [ZERO], indicator will be back to zero, and zero light
will be on;
B, Zero key will only be valid when weighs on platform is within
manual zero range;
C, Zero operation is valid only when stable light is on;
D, If indicator is at net weight mode, press [TARE PRESET] to
set it as 0, and back to weighing mode then zero operation is
valid;
4.3.3 Tare operation
There are three methods to tare:
-Method 1, Normal tare
Press [tare] key when weighing data is positive and stable,
the displayed weighing data will be regarded as tare weight,
then indicator will display 0 and net light is on;
7
-Method 2,Preset tare
Press [TARE PREST] key at weighing status, indicator enter into
tare preset window, the displayed data is the former tare. If
new tare is needed, then input by 123eric key and press [INPUT]
to confirm. Press [] to return back weighing mode;
-Method 3,Call tare weight according to vehicle no.
Press [VEHICLE NO.] at weighing status, indicator enter into
vehicle/tare setup window. After inputting the right vehicle
no., press [INPUT] to call the tare of this vehicle from the
memory. If no need to change the tare of this vehicle, then
press [TARE] to regard the tare as current tare and back to
weighing mode;
5. Menu Operation
5.1 Menu list
KEY MENU SUB-MENU
[Cargo No.] Cargo Name
[Vehicle No.] Vehicle No./ Tare
[SAVE PRINT] Input Vehicle No./
Cargo No.
[TARE PRESET] Preset Tare
[SAVE TARE] Vehicle No./ Tare
[REP PRINT] Daily Report Repot Date
General Report 1
General Report 2
General Report 3
General Report 4
General Report 5
General Report 6
[DELETE] Delete by Time Record Date
Delete by Vehicle
No.
Vehicle No.
Delete by Cargo No. Cargo Name
Delete All RCD
[CALIBRATE] Calibrate PWD
IDT Calibrate Division
Decimal Point
F.S.
Zero point
Load
Angel Adjust
Manual method Quantity of LOCEL
LOCEL Address
Coefficient Adjust
Auto method Quantity of LOCEL
Load Weight
LOCEL Calibrate No. of LOCEL
Note: Setup used by
LOCEL supplier
Zero Point of LOCEL
50% F.S. of LOCEL
F.S. of LOCEL
LOCEL Address LOCEL New Address
8
Change LOCEL ISN
LOCEL Type
Unit
Zero Track Range
Manual Zero Range
Auto Zero Range
Dgtl Filter Int.
Calibrate P of IDT Zero Point
Calibrate
Coefficient
[CHECK] Check by Date Record Date
Check by Vehicle
No.
Vehicle No.
Check by Cargo No. Cargo Name
Check VEHNO of RCD!
Check CARNO of RCD!
Check Ovrload
Record
[SETUP] Prnt Setup Function PWD
Prnt Method
Prnter Type
Prnt Back Zero Rst
Prnt Format
Min. Prnt Weight
Filled Prnt option
Company Name
Comm Setup Comm Method
Comm Address
Baud Rate
Date/Time Setup Calibrate PWD
Date/Time Setup
Date/Time Display
Display Contrast
Cargo No. Enable
Vehicle No. Enable
Calibrate PWD
Change
Timing PWD Change
LOCEL Check
LOCEL Searching
IDT ISN
5.2 Operation mode description
There are three operation modes for user to select which could
offer quick, intelligent and convenient way for operation.
5.2.1 Single key mode
Press one key to execute corresponding operation, keys that
works in this way are: [4/JKL SUP PRINT] [ZERO] [TARE] [0
BACKLIGHT][WEIGH]
Example: press [ZERO] at weighing mode, then indicator would
zero
5.2.2 Single Menu mode
9
For operation that needs value input, press one key, then direct
to value input, keys that works in this way are: [1/ABC Cargo
No.] [2/DEF Vehicle No.] [SAVE TARE] [6/PQR TARE PRESET] [8/
VWX SAVE PRINT]
Example: Press [1/ABC Cargo No.] at weighing mode, it directs
to Cargo Name WINDOW. Input area displays against white while
input mode is displayed at the right top corner. User could
press [INPUT MODE] to switch among different input modes, that
is 123/ABC/PINYIN/SIGN. Press [INPUT] to save while [] to main
window. Cargo Name WINDOW displays like following
5.2.3 Menu bar mode
For these not frequently used and complicated parameters, user
could find parameter according to type through menu bar. There
are five keys that direct to sub menu for more operation
according to function. Menu list is as described above. The
five keys are: [3/GHI SETUP] [CHECK] [5/ MNO REP PRINT] [9/YZ
CALIBRATE] [DELETE]
Example: Press [SETUP] at weighing mode, then operate like
mobile phone style to select the right menu item you want to
setup parameter, then press [INPUT] to parameter setup window
or next menu selection window. It displays like followed window:
Then suppose you select menu item Display Contrast, it displays
like this:
Press [INPUT],then it enters into Display Contrast Window, and
window is as followed:
Press [INPUT] to save while [] to main window
Cargo Name [123]
ValueSteel Code:0
(Input cargo name)
[]Back [INPUT] Confirm
Prnt Setup Display Contrast
Comm Setup Cargo No. Enable
Date/Time Setup Vehicle No. Enable
Date/Time Display []Back [INPUT] Confirm
Prnt Setup Display Contrast
Comm Setup Cargo No. Enable
Date/Time Setup Vehicle No. Enable
Date/Time Display []Back [INPUT] Confirm
Display Contrast [123]
Value4
(Input range:0~5)
[]Back [INPUT] Confirm
10
5.3 Menu Operation
5.3.1 Cargo Name Window Setup
Press [Cargo No.] at weighing mode, it displays:
Press [INPUT],
After input cargo name and press [INPUT], indicator will search
whether corresponding code exits, if exits, then it displays
the right code, if not exit, then it creates new code and
displays. If user knows code, then first input code, then
indicator will search the right corresponding cargo name
according to the input code. If indicator cant search the right
cargo name according to code, then it displays error.
Then press [INPUT] to save while [] to main window
Note:
5.3.2 Vehicle No./ Tare Setup
Press [Vehicle No.] or [SAVE TARE] at weighing mode, it
displays:
Press [INPUT],
Press [INPUT],
Input area Input mode Note
Cargo Name 123/ABC/PINYIN/SIGN Max. 10 character
Code 123 Max 3 character
Cargo Name [123]
Cargo NameSteel Code:1
(Input cargo name)
[]Back [INPUT] Confirm
Cargo Name [123]
Cargo NameSteel Code:1
(Input cargo name)
[]Back [INPUT] Confirm
Vehicle No./ Tare [123]
Vehicle No.A12345 Code:0
Tare:1000 kg
[]Back [INPUT] Confirm
Vehicle No./ Tare [123]
Vehicle No.A12345 Code:0
Tare:1000 kg
[]Back [INPUT] Confirm
11
After input Vehicle No. and press [INPUT], indicator will
search whether corresponding code exits, if exits, then it
displays the right code, if not exit, then it creates new code
and displays. If user knows code, then first input code, then
indicator will search the right corresponding Vehicle No.
according to the input code. If indicator cant search the right
Vehicle No. according to code, then it displays error.
After input Vehicle No. and code, it will automatically go to
tare set, the tare value is just the tare of the vehicle. If
there is no save, then tare is regarded as 0; if need to change
the tare, then input by 123eric key and press [INPUT] to save,
while [] to main window
If code is 0, it indicates that just weigh for cargo, tare cant
be input.
5.3.3 Input Vehicle No./ Cargo No. Setup (Save and print setup)
Press [SAVE PRINT] at weighing mode, it displays:
Press [INPUT],
Press [INPUT],
Press [INPUT],
Input area Input mode Note
Vehicle No. 123/ABC/PINYIN/SIGN Max. 10 character
Code 123 Max 3 character
Tare 123 Max 6 character
Vehicle No./ Tare [123]
Vehicle No.A12345 Code:0
Tare:1000 kg
[]Back [INPUT] Confirm
Input Vehicle No./ Cargo No. [123]
Vehicle No.A12345 Code:1
Cargo No.:--- kg Code:1
[]Back [INPUT] Confirm
Input Vehicle No./ Cargo No. [123]
Vehicle No.A12345 Code:1
Cargo No.:--- kg Code:1
[]Back [INPUT] Confirm
Input Vehicle No./ Cargo No. [123]
Vehicle No.A12345 Code:1
Cargo No.:--- kg Code:1
[]Back [INPUT] Confirm
Input Vehicle No./ Cargo No. [123]
Vehicle No.A12345 Code:1
Cargo No.:--- kg Code:1
[]Back [INPUT] Confirm
12
After input Vehicle No./Cargo NO. and press [INPUT], indicator
will search whether corresponding code exits, if exits, then
it displays the right code, if not exit, then it creates new
code and displays. If user knows code, then first input code,
then indicator will search the right corresponding Vehicle
No./Cargo No. according to the input code. If indicator cant
search the right Vehicle No./ Cargo No. according to code,
then it displays error.
After 4 input area all finished, press [INPUT] to save and
execute print, while [] to main window
5.3.4 Preset Tare Setup
Press [TARE PRESET] at weighing mode, it displays:
Press [INPUT] to save while [] to main window. If preset tare
is not zero, then indicator displays net weight and net light
is on; if preset tare is zero, then it displays gross weight.
If preset tare value is not integer times of division, then
it will round integer times of division
5.3.5 REP PRINT Setup
Press [REP PRINT] at weighing mode, it displays:
Press [][ ] to select the report format. When select Daily
report and press [INPUT], it displays:
Input area Input mode Note
Vehicle No. 123/ABC/PINYIN/SIGN Max. 10 character
Code(up) 123 Max 3 character
Cargo No. 123/ABC/PINYIN/SIGN Max. 10 character
Code(down) 123 Max 3 character
Input area Input mode Note
Tare 123 Max. 6 character
Input area Input mode Note
Tare 123 Max. 6 character
Input area Note
Daily Report Print weighing records by date, 3
shares in different forms
General Report 1~
General Report 6
Print all weighing records in 6
formats. Format, refer to appendix Preset Tare [123]
Tare:0.000 kg
(Input preset tare value)
[]Back [INPUT] Confirm
Daily Report General Report 4
General Report 1 General Report 5
General Report 2 General Report 6
General Report 3 []Back [INPUT] Confirm
13
After input the report date and press [INPUT] it prints out
all records related to the date and back to weighing mode when
printing finishes. Press [] to main window;
When selects the other report format and press [INPUT], it
prints corresponding reports and back to weighing mode; Press
[] to main window;
5.3.6 CALIBRATE Setup
First open the PB seal socket and turn on the calibration
switch .Press [CALIBRATE] at weighing mode, it displays:
After input the right password, and press [INPUT], it directs
to calibration setup window. If password is not right, it
requires to input again after alarm. If you input the wrong
password by 3 times, then it back to weighing mode. Press []
to main window;
Calibration Setup Window
Press [][ ] to turn page:
IDT Calibrate
After select this menu item and press [INPUT], it directs to
the course of calibration:
Input area Input mode Note
Date 123 From left to right,
year/month/day, 2 digits for
each item
Input area Input mode Note
PWD 123 6 digit password,
default is 888888
Repot Date [123]
Date:06/08/31
(Input the record date you want to print)
[]Back [INPUT] Confirm
Calibrate PWD [123]
PWD:******
(Input correct calibration password)
[]Back [INPUT] Confirm
IDT Calibrate LOCEL Type
Angel Adjust Unit
LOCEL Calibrate Zero Track Range
LOCEL Address Change []Back [INPUT] Confirm
Manual Zero Range
Auto Zero Range
Dgtl Filter Int.
Calibrate P of IDT []Back [INPUT] Confirm
14
First, it displays the division setup window:
After division input and press [INPUT], it displays the decimal
point setup window:
After decimal point inut and press [INPUT], it displays the
full capacity(F.S) setup window:
After F.S. input and press [INPUT], it displays the zero point
calibration window:
Press [INPUT] after AD code is stable while there is no load,
then indicator come to load point calibration window:
After weight is loaded and input by 123eric key, press [INPUT]
when AD code is stable, then it returns back to main menu window
When AD code changes in a small range, then its stable
Input area Input mode Note
Decimal point 123 0,1,2,3,4
Input area Input mode Note
F.S. 123 Max. 6 character
Input area Input mode Note
Division 123 1,2,5,10,20,50 optional
Input area Input mode Note
Load 123 Max. 6 character
Division [123]
Division:1
(1,2,5,10,20,50 optional)
[]Back [INPUT] Confirm
Decimal Point [123]
Decimal Point:3
(From 0~4)
[]Back [INPUT] Confirm
F.S. [123]
F.S.:200.000 kg
(Input the full capacity)
[]Back [INPUT] Confirm
Zero point (AD code of LOCEL)
1569 []Back [INPUT] Confirm
Load:200.000 kg [123]
298568 []Back [INPUT] Confirm
15
Angel Adjust
After select this menu item and press [INPUT], it directs to
the course of angel adjust, it displays the Angel Adjust window:
:
Press [][ ] to select the method, and press [INPUT] to confirm;
Note: When load cell is changed, then select manual method to
adjust and setup the relationship of load cell quantity and
address.
Manual method
First, it comes to Quantity of LOCEL window
After input quantity of load cell, press [INPUT], it directs
to LOCEL Address window:
After input address, press [INPUT], it directs to Coefficient
Adjust window. Press [], then it back to Angel Adjust window.
After coefficient is input, press [INPUT] it directs to LOCEL
Address window, Press [], then it back to Angel Adjust window.
In manual method, the cycle 123ber of the two parameters is
decided by the quantity of load cell. When all setup is finished,
it back to Angel Adjust window or press [WEIGH] to weighing
mode.
Input area Note
Manual method Adjust the angel according to known adjust rate
Auto method Adjust the angel according to adjust rate by the
loaded weight
Input area Input mode Note
Coefficient 123 6 digits, from .50000~2.00000
Input area Input mode Note
Quantity 123 2 digits, from 1~16
Input area Input mode Note
Address. 123 2 digits, from 0~63
Input area Input mode Note
Quantity 123 2 digits, from 1~16
Manual method
Auto method
[]Back [INPUT] Confirm
Quantity of LOCEL [123]
Quantity:8
(From 1~16)
[]Back [INPUT] Confirm
LOCEL Address (01/08) [123]
Address.:1
(From 0~63)
[]Back [INPUT] Confirm
Coefficient Adjust [123]
Coefficient:1.00450
(From 0.50000~2.00000)
[]Back [INPUT] Confirm
16
Auto method
First, it comes to Quantity of LOCEL window
After input quantity of load cell, press [INPUT], it directs
to Load Weight window:
After load weight and wait until platform is stable, press
[INPUT], it directs to LOCEL ISN window:
After ISN is stable, press [INPUT] it directs to next load weight
window.
Repeat load weight operation, when it reaches the load weight
times(equal to load cell quantity), press [INPUT], indicator
finishes angel adjust.
LOCEL Calibrate
As different load cell supplier offers different load cell
calibration method, hence here only YAOHUA load cell
calibration method is listed. If load cell is not YAOHUA, then
indicator goes back to main window after alarm.
Note: When calibrating for load cell, indicator could only be
connected to 1 pre-calibrate load cell.
After select this menu item and press [INPUT], it directs to
the course of load cell calibration, it displays the No. of
LOCEL window:
:
Input area Input mode Note
Quantity 123 2 digits, from 1~16
Input area Input mode Note
No. 123 2 digits, from 1~16
Quantity of LOCEL [123]
Quantity:6
(From 1~16)
[]Back [INPUT] Confirm
Load Weight (01/08)
(Load weight at assigned location of
platform)
[]Back [INPUT] Confirm
LOCEL ISN(01/08)
1998202 []Back [INPUT] Confirm
Load Weight (02/08)
(Load weight at assigned location of
platform)
[]Back [INPUT] Confirm
No. of LOCEL [123]
No.:1
(From 1~16)
[]Back [INPUT] Confirm
17
After input NO. of load cell and press [INPUT], it displays
the Zero Point of LOCEL window:
Press [INPUT] when there is no load, it directs to 50% F.S.
of LOCEL window after indicator its stable. If indicator didnt
search any load cell, then it returns back to weighing mode
after alarms.
Press [INPUT] when its at 50% F.S. of LOCEL, it directs to
F.S. of LOCEL window after indicator its stable.
Press [INPUT] when its at F.S. of LOCEL, it returns to weighing
mode.
LOCEL Address Change
After select this menu item and press [INPUT], it directs to
LOCEL Address Change window:
When changing address for load cell, indicator could only be
connected to 1 load cell. Input new address and press [INPUT],
it directs to LOCEL ISN window
Input area Input mode Note
Value 123 Max. 6 digits, without
decimal point
Input area Input mode Note
Value 123 Max. 6 digits, without
decimal point
Input area Input mode Note
Address 123 2 digits, from 0~63
Zero Point of LOCEL
(Press [INPUT] at no load)
[]Back [INPUT] Confirm
50% F.S. of LOCEL [123]
Value: 2000
(Press [INPUT] after 50% F.S. is loaded)
[]Back [INPUT] Confirm
F.S. of LOCEL [123]
Value: 4000
(Press [INPUT] after F.S. is loaded)
[]Back [INPUT] Confirm
LOCEL New Address [123]
Address: 1
(From 0~63)
[]Back [INPUT] Confirm
LOCEL 01 ISN
200000 []Back [INPUT] Confirm
18
Press [INPUT] to main menu, while [] to main window
LOCEL Type
After select this menu item and press [INPUT], it directs to
LOCEL Type window
Press [INPUT] to save while [] to main window
UNIT
After select this menu item and press [INPUT], it directs to
UNIT window
Press [INPUT] to save while [] to main win
Zero Track Range
After select this menu item and press [INPUT], it directs to
Zero Track Range window
Press [INPUT] to save while [] to main window
Manual Zero Range
After select this menu item and press [INPUT], it directs to
Manual Zero Range window
Press [INPUT] to save while [] to main window
Input area Note
HBM LOCEL Digital load cell Protocol HBM
YAOHUA LOCEL Digital load cell Protocol YAOHUA
Only 1 LOCEL Digital load cell Protocol ONLY 1
Input area Note
KG KG is the unit
T Ton is the unit
Input area Input mode Note
Range 123 2 digits, from 0.0~4.5,
0.5 as the interval
Input area Input mode Note
Range 123 3 digits,
0,2,4,10,20,40,100
HBM LOCEL
YAOHUA LOCEL
Only 1 LOCEL
[]Back [INPUT] Confirm
KG
T
[]Back [INPUT] Confirm
Zero Track Range [123]
Range: 0.5 e
(From 0.0~4.5, 0.5 as the interval)
[]Back [INPUT] Confirm
Manual Zero Range [123]
Range: 2.0 %
(0,2,4,10,20,40,100)
[]Back [INPUT] Confirm
19
Auto Zero Range
After select this menu item and press [INPUT], it directs to
Auto Zero Range window
Press [INPUT] to save while [] to main window
Dgtl Filter Int.
After select this menu item and press [INPUT], it directs to
Dgtl Filter Int. window
Press [INPUT] to save while [] to main window
Calibrate P of IDT
After select this menu item and press [INPUT], it directs to
Calibrate P of IDT window
Press [INPUT], it directs to the Calibrate Coefficient window:
Input area Input mode Note
Range 123 3 digits,
0,2,4,10,20,40,100
Input area Input mode Note
Value 123 Max. 6 digits, its only
changed when replace indicator
without re-calibration and
its changed according to the
replaced indicator
Input area Input mode Note
Int. 123 1 digit, from 0~4
The bigger the value is,
the better stability and
lower response speed it is
Input area Input mode Note
Value 123 Max. 6 digits, its only
changed when replace indicator
without re-calibration and
its changed according to the
replaced indicator
Auto Zero Range [123]
Range: 2.0 %
(0,2,4,10,20,40,100)
[]Back [INPUT] Confirm
Dgtl Filter Int. [123]
Int.: 2
(From 0~4)
[]Back [INPUT] Confirm
Zero Point [123]
Value: 2145
(Input AD code at zero point)
[]Back [INPUT] Confirm
Calibrate Coefficient [123]
Value: 0.44336
Input Calibrate Coefficient)
[]Back [INPUT] Confirm
20
Note: The menu also directs to check or modification for
calibrated indicator.
5.3.7 Setup Window
Press [SETUP] at weighing mode, it displays:
Press [][ ] to turn page:
Prnt Setup
After select this menu item and press [INPUT], it directs to
Function PWD window
Press [INPUT], it directs to Prnt Setup window
Prnt Method
After select this menu item and press [INPUT], it directs to
Prnt Method window
Press [input] after select, indicator save the setup. Press
[] to main menu while press [WEIGH] to main window.
Input area Input mode Note
PWD 123 6 digits, default is
888888
Input area Note
Auto Prnt Auto print and save current weighing data
Manual Prnt Press [SAVE PRINT]or [SUP PRINT], then it can
print and save current weighing data
Prnt Setup Display Contrast
Comm Setup Cargo No. Enable
Date/Time Setup Vehicle No. Enable
Date/Time Display []Back [INPUT] Confirm
Calibrate PWD Change IDT ISN
Timing PWD Change
LOCEL Check
LOCEL Searching []Back [INPUT] Confirm
Function PWD [123]
PWD:
(Input correct function password)
[]Back [INPUT] Confirm
Prnt Method Min. Prnt Weight
Prnter Type Filled Prnt option
Prnt Back Zero Rst Company Name
Prnt Format []Back [INPUT] Confirm
Auto Prnt
Manual Prnt
[]Back [INPUT] Confirm
21
Prnter Type
After select this menu item and press [INPUT], it directs to
Prnter Type window
Prnt Back Zero Rst
After select this menu item and press [INPUT], it directs to
Prnt Back Zero Rst window
Prnt Format
After select this menu item and press [INPUT], it directs to
Prnt Format window
Min. Prnt Weight
After select this menu item and press [INPUT], it directs to
Min. Prnt Weight window
Input area Note
Prnt Invalid! Printing function forbidden
Panasonic KX-P1131 Panasonic KX-P1131 printer is chosen
EPSON LQ300K EPSON LQ300K is chosen
EPSON LQ-1600K EPSON LQ-1600K is chosen
Input area Input mode Note
Value 123 3 digits, from 0~100, 0 means
print only when indicator is
back to zero; while 100 means
print without any restrict.
Input area Note
Record Format Print report in record format
1 Link Format Print report in 1 link format
2 Link Format Print report in 2 link format
3 Link Format Print report in 3 link format
Prnt Invalid!
Panasonic KX-P1131
EPSON LQ300K
EPSON LQ-1600K []Back [INPUT] Confirm
Prnt Back Zero Rst [123]
Value: 0 %
(Input restrict range 0~100)
[]Back [INPUT] Confirm
Record Format
1 Link Format
2 Link Format
3 Link Format []Back [INPUT] Confirm
22
Filled Prnt option
After select this menu item and press [INPUT], it directs to
Filled Prnt option window
Company Name
After select this menu item and press [INPUT], it directs to
Company Name window
Company name can be printed out on weighing bill.
Comm Setup
After select this menu item and press [INPUT], it directs to
Comm Setup window
Comm Method
After select this menu item and press [INPUT], it directs to
Comm Method window
Input area Input mode Note
Value 123 Max. 6 digit, the min. print
weight should be more than 10e,
Input area Note
Fill Format Disable Printer wont adopt fill format
Fill Format Enable Printer will adopt fill format
Input area Input mode Note
Name 123/ABC/PINYIN/SIGN Max. 23 character
Min. Prnt Weight [123]
Value: 0.010 kg
(>=10 e)
[]Back [INPUT] Confirm
Fill Format Disable
Fill Format Enable
[]Back [INPUT] Confirm
Company Name [123]
Name: Yaohua Weighing
(Input company name)
[]Back [INPUT] Confirm
Comm Method
Comm Address
Baud Rate
[]Back [INPUT] Confirm
Command Method
Continuous Method
[]Back [INPUT] Confirm
23
Comm Address
After select this menu item and press [INPUT], it directs to
Comm Address window
Baud Rate
After select this menu item and press [INPUT], it directs to
Baud Rate window
Date/Time Setup
After select this menu item and press [INPUT], it directs to
Function PWD window
Press [INPUT], and it directs to
After input date and press [INPUT],it directs to:
Input area Note
Command Method Indicator communicates with PC in
command method
Continuous Method Indicator communicates with PC in
continuous method
Input area Input mode Note
PWD 123 6 digits, default is
888888
Input area Input mode Note
Address 123 Max. 2 digits, from 1~26
Input area Input mode Note
Value 123 Max. 4
digits,600,1200,2400,4800,9600
Comm Address [123]
Adddress:1
(From 1~26)
[]Back [INPUT] Confirm
Baud Rate [123]
Value:1200 b/s
(600,1200,2400,4800,9600)
[]Back [INPUT] Confirm
Function PWD [123]
PWD:
(Input correct function password)
[]Back [INPUT] Confirm
Date/Time Setup [123]
Date:06/08/31
Time:20:16:53
[]Back [INPUT] Confirm
24
Date/Time Display
After select this menu item and press [INPUT], it directs to
Date/Time Display window
Display Contrast
After select this menu item and press [INPUT], it directs to
Display Contrast window
Cargo No. Enable
After select this menu item and press [INPUT], it directs to
Cargo No. Enable window
Input area Input mode Note
Date 123 From left to right:
Year/Month/Day
Time 123 From left to right:
Hour/Minute/Second
Input area Note
Display Time Display time at weighing window
Display Date Display date at weighing window
No display No display for time or date at all
Input area Input mode Note
Value 123 Max. 1 digit, from 0~5
0 means LCD/VED contrast lowest
5 means LCD/VED contrast highest
Input area Note
Cargo No. Enable Cargo No. can be set up and printed out
Cargo No. Disable Cargo No. cant be set up and printed out
Date/Time Setup [123]
Date:06/08/31
Time:20:16:53
[]Back [INPUT] Confirm
Display Time
Display Date
No Display
[]Back [INPUT] Confirm
Display Contrast [123]
Value:4
(From 0~5)
[]Back [INPUT] Confirm
Cargo No. Enable
Cargo No. Disable
[]Back []Select [INPUT]
Confirm
25
Vehicle No. Enable
After select this menu item and press [INPUT], it directs to
Vehicle No. Enable window
Calibrate PWD Change
After select this menu item and press [INPUT], it directs to
Calibrate PWD Change window
After input the original password, if password is right, then
it directs to next step of Calibrate PWD Change window, or else
it requires to input again after alarms. Indicator goes back
to main menu after 3 times wrong input.
After input new calibration password and press [INPUT], it
appears again:
The new password input two times should be the same.
Timing PWD Change
After select this menu item and press [INPUT], it directs to
Calibration PWD window
Input area Note
Vehicle No. Enable Vehicle No. can be set up and printed out
Vehicle No. Disable Vehicle No. cant be set up and printed out
Input area Input mode Note
PWD 123 6 digits,
Input area Input mode Note
PWD 123 6 digits,
Vehicle No. Enable
Vehicle No. Disable
[]Back []Select [INPUT] Confirm
Calibrate PWD Change [123]
PWD:
(Input the original calibration password)
[]Back [INPUT] Confirm
Calibrate PWD Change [123]
PWD:
(Input new calibration password)
[]Back [INPUT] Confirm
Calibrate PWD Change [123]
PWD:
(Input new calibration password again)
[]Back [INPUT] Confirm
Calibration PWD [123]
PWD:
(Input the correct calibration password)
[]Back [INPUT] Confirm
26
After input the calibration password, if password is right,
then it directs to next step of Timing power off Date window,
or else it requires to input again after alarms. Indicator goes
back to main menu after 3 times wrong input.
LOCEL Check
After select this menu item and press [INPUT], it directs to
LOCE NO. window
Input the No. of load cell you want to check and press [INPUT],it
directs to LOCEL ISN window
Press [INPUT], indicator will display ISN of all load cell one
by one.
LOCEL Searching
After select this menu item and press [INPUT], it directs to
LOCE Searching window
After search finishes, if there is load cell searched, it
displays:
0101: 01 stands for the No. of load cell while 01 stands for
the address of load cell, the max. NO. of load cell is equal
to the quantity of load cell.
Input area Input mode Note
PWD 123 6 digits,
Input area Input mode Note
Date 123 6 digits, from left to right:
Year/Month/Day
Input area Input mode Note
No. 123 2 digits, from
1~16
Timing power off Date [123]
Date: 99/99/99
(Input the timing date for power off )
[]Back [INPUT] Confirm
LOCEL NO. [123]
No.: 1
(From 1~16 )
[]Back [INPUT] Confirm
LOCEL 01 ISN
200000 []Back [INPUT] Confirm
LOCEL Searching! Please Wait!
LOCEL Searching( No./Add.)
0101 0202 0303 0404 0505 0606
0707 0808 0909 1010 1111 1212
1313 1414 1515 1616 []Back
27
If there is no load cell searched, it displays:
IDT ISN
After select this menu item and press [INPUT], it directs to
IDT ISN window
Check
After select this menu item and press [INPUT], it directs to
Check window
Check by Date
After select this menu item and press [INPUT], it directs to
Check by date window
After input the date, press [INPUT],it displays:
Input area Note
Check by Date Check record by date
Check by Vehicle No. Check record by vehicle no.
Check by Cargo No. Check record by cargo no.
Check VEHNO of RCD! Check the vehicle no. of the record
Check CARNO of RCD! Check the cargo no. of the record
Check Ovrload Record Check overload records
Input area Input mode Note
Date 123 6 digits, from left to right:
Year/Month/Day
Non-con!
[]Back
250000 []Back
Check by Date Check CARNO of RCD!
Check by Vehicle No. Check Ovrload Record
Check by Cargo No.
Check VEHNO of RCD! []Back [INPUT] Confirm
Record Date [123]
Date: 06/04/12
(Input the record date for check )
[]Back [INPUT] Confirm
0001/0020 06/04/12 12:32:30
Vehicle NO.:A12345 Cargo No.:Steel
GW:2000kg Tare:50kg
NW:1950kg [] Page Down
28
Press [], it shows the next record by this date:
Press [DELETE] to delete the record while you are checking
Check by Vehicle NO.
After select this menu item and press [INPUT], it directs to
Check by Vehicle NO. window
After input the vehicle no. or code, press [INPUT],it displays:
Press [], it shows the next record by this vehicle no.:
Press [DELETE] to delete the record while you are checking
Check by Cargo NO.
After select this menu item and press [INPUT], it directs to
Check by Cargo NO. window
After input the cargo no. or code, press [INPUT],it displays:
Press [], it shows the next record by this cargo no.:
Input area Input mode Note
No. 123/ABC/PINYIN/SIGN Max.10 character
Code 123 Max. 3 character
Input area Input mode Note
No. 123/ABC/PINYIN/SIGN Max.10 character
Code 123 Max. 3 character
0002/0020 06/04/12 12:40:30
Vehicle NO.:A12345 Cargo No.:Steel
GW:2050kg Tare:50kg
NW:2000kg [] Page Down
Vehicle NO. [123]
No.: A12345 Code:0
(Input the vehicle no. of the record )
[]Back [INPUT] Confirm
0001/0020 06/04/12 12:40:30
Vehicle NO.:A12345 Cargo No.:Steel
GW:2050kg Tare:50kg
NW:2000kg [] Page Down
0002/0020 06/04/12 12:45:30
Vehicle NO.:A12345 Cargo No.:Steel
GW:2050kg Tare:50kg
NW:2000kg [] Page Down
Cargo NO. [123]
No.: Steel Code:1
(Input the cargo no. of the record )
[]Back [INPUT] Confirm
0001/0030 06/04/12 12:32:30
Vehicle NO.:A12345 Cargo No.:Steel
GW:2000kg Tare:50kg
NW:1950kg [] Page Down
29
Press [DELETE] to delete the record while you are checking
Check VEHNO of RCD!
After select this menu item and press [INPUT], it directs to
Check VEHNO of RCD window
Press [] [] to turn page
Check CARNO of RCD!
After select this menu item and press [INPUT], it directs to
Check CARNO of RCD window
Press [] [] to turn page
Check Ovrload Record
After select this menu item and press [INPUT], it directs to
Check Ovrload Record window
Press [] [] to turn page
Delete
After select this menu item, it directs to Delete window
Input area Note
Delete by Time Delete record by time
Delete by Vehicle No. Delete record by vehicle no.
Delete by Cargo No. Delete record by cargo no.
Delete All RCD Delete all record in indicator
0002/0030 06/04/12 12:40:30
Vehicle NO.:A12345 Cargo No.:Steel
GW:2050kg Tare:50kg
NW:2000kg [] Page Down
0001/0009
Vehicle No.: B12345 Code:001
Tare:0.000kg
[]Back [] Page Down
0001/0004
Cargo No.: Steel Code:001
[]Back [] Page Down
0001/0002
Date:06/11/13 Time:15:26:48
GW:223 394kg
[]Back [] Page Down
Delete by Time
Delete by Vehicle No.
Delete by Cargo No.
Delete All RCD []Back [INPUT] Confirm
30
Delete by Time
After select this menu item and press [INPUT], it directs to
Delete by Time window
After input the date, press [INPUT],it displays:
Press [INPUT], then delete the record, press [], then cancel
delete operation
Delete by Vehicle No.
After select this menu item and press [INPUT], it directs to
Delete by Vehicle NO. window
After input the vehicle no. and code no, or directly press
[INPUT],it displays:
Press [INPUT], then delete the record, press [], then cancel
delete operation
Delete by Cargo No.
After select this menu item and press [INPUT], it directs to
Delete by Cargo NO. window
After input the cargo name and code no, or directly press
[INPUT],it displays:
Press [INPUT], then delete the record, press [], then cancel
delete operation
Input area Input mode Note
Date 123 6 digits, from left to right:
Year/Month/Day
Record Date [123]
Date: 06/04/12
(Input the record date for delete )
[]Back [INPUT] Confirm
Record by this time deleted?
[]Back [INPUT] Confirm
Vehicle NO. [123]
No: A12345 Code:1
(Input the vehicle no. of record for delete )
[]Back [INPUT] Confirm
Record by VEHNO. deleted?
[]Back [INPUT] Confirm
Cargo Name. [123]
Name: Steel Code:1
(Input the cargo name of record for delete )
[]Back [INPUT] Confirm
Record by CARNO. deleted?
[]Back [INPUT] Confirm
31
Delete all record
After select this menu item and press [INPUT], it directs to
Delete all record window
Press [INPUT], then delete the record, press [], then cancel
delete operation
6. Character Input
6.1 Brief Introduction
Xk3190 DS2 supports NUM(123), English(ABC), Chinese (PINYIN)
and Sign to input the character, user can input the required
information through compound inputting. It is quite similar
to the popular cell phones T9 input method. Also Chinese PINYIN
has the function to index the words which have several different
pronunciations, can successfully raise the efficiency.
6.2 Operation
When input VEHICLE NO, CARGO, COMPANY NAME etc, you can use
Number, English, Chinese PINYIN and Sign to mix input the
records, other parameters only support the number input. When
allow compound inputs, press [INPUT MODE] key to switch the
input way. Press [DELETE] key can delete the inputs character
by character.
Screen up-right
corner shows
Input Status
123 Number inputs
ABC English inputs [Capital]
abc English inputs [Small]
PINYIN Chinese PINYIN
.?! Sign
1 Number Inputs
Press the related Number key can input the number
2 English inputs[Capital] / English inputs[small]
First press [INPUT MODE] key to switch the input to English
inputs [Capital] or English inputs [small], after that you can
input the information by press the key which signed the related
letter. E.g. if you want to input letter C, just press key
[1/ABC].
1Continuously press the same character key in 1 second interval,
the input letter will be switched within that keys letter
range.
E.g.Continuously press the key [1/ABC] in 1 second, the
inputted letter will be switched among A.B.C and finally get
one.
2Press the key over 1 second interval, then you will get the
keys related first letter after each press. If u want to input
the other letter of that key, please repeat the 1) operation
to continuously press the same character key in 1 second
interval and select that requested letter.
E.g.: if u want to input HAI, please continuously press [3/GHI]
twice within 1 second and get H, after 1 second press [1/ABC]
All record deleted?
[]Back [INPUT] Confirm
32
get A, and again after 1 second continuously press [3/GHI] three
times to get I. It is finished.
3 Chinese PINYIN inputs
First press [INPUT MODE] to switch the input to Chinese PINYIN.
1Directly press the key according to the PINYIN sequence of
the required Chinese character, then the bottom part of the
screen will display one or more right PINYIN which match the
request and will show their related Chinese characters.
2 Presskey to select the demanded PINYIN. After
selection, the PINYIN color will be highlighted. (The related
Chinese character will be changed according to Pinyins
selection)
3 Presskey to select the required Chinese character.
After selection the Chinese character color will be highlighted.
(Each row can display 15 Chinese characters. When the quantity
of the character which match the request was exceeding 15,
indicator will automatically turn to next or last row. All
PINYIN and Chinese character can be displayed circularly).
4 When get the required Chinese character, press [INPUT] key,
the indicator will put the selected character to the input area
and the cursor will wait for next inputs. When all inputs
finished, press [INPUT] key to save the inputted characters
which listed inside the input area.
E.g. if you want to input the Chinese word seaChinese PINYIN
was hai, then press the following key3/GHI1/ABC
3/GHI by sequenceno need to care about the time interval.
The bottom of the screen will display two PINYIN which match
your type, that is gaiand hai. Presskey to select hai,
you can find out the related Chinese character at bottom of
the screen. Presskey twice to select Chinese character
sea and finally pressINPUT to put sea to the input area.
4 Sign inputs
First pressINPUT MODEswitch to Sign inputs
1 The bottom of the screen will display all the signs waiting
for your selection. Pressto select the required signs,
after select the signet color will turn to highlighted. Press
INPUTKeyIndicator will put the selected signs into the
input area, and automatically turn back to the PINYIN inputs
waiting for input another Chinese Character.
2 If u want to continue input the signs, please pressINPUT
MODEkey to switch the input status, select Sign and input the
required sign. When finish the inputting please press [INPUT]
to save the information inside the input area.
E.g.If you want to input pressINPUT MODEswitch to
the sign inputs. The bottom of the screen will display a series
of the signs, press 5 times to get ?, pressINPUT
key to put the into the input area. At the same time the
input status back to PINYIN inputs.
Chapter 7 Calibration
7.1Calibration Setting
First turn on the seal baseadjust the inside calibration switch
to allow the calibration. In weighing modepress9/YZ
Calibrate,the indicator shows:
33
After input the correct password, pressINPUTto enter the
Calibration setting window. If the password inputted is wrong,
system will ask user to re-input, indicator will automatically
back to weighing mode after 3 times continuously wrong typing.
Also you can pressto directly back to weighing mode.
Calibration setting window
Presskey to page up and down
First we should make the angel adjustment, the detail as
follows:
1Angel adjustment
Pressto select corners difference adjustment item
inside the calibration setting windowpressINPUTto enter
the corner difference adjustment window.
Input area Input mode Note
Set the
password
value
Number Input 6 digit password, each* means
1 digit.
If input the number over 6 digit,
indicator only keep the first 6 digit.
Default password is 888888
Settings Set description
Manual Use the available load cells adjustment
coefficient to adjust the corners difference
Auto Through adding the weight, indicator will
re-calculate the load cells adjustment
coefficient to adjust the corners difference.
Calibration PWD 123
Value******
(Use Number key to input the right
Calibration PWD)
RETURN INPUTOK
IDT Calibrate Locel type
Angel adjust Weighing unit
LOCEL calibration Zero track range
LOCEL Address Change select INPUTOk
Manual zero range
Auto zero range
Dgtl filter Int
Calibrate P of IDT select INPUTok
Suppose the digital load cell had calibrated before send out,
and was connected correctly with the indicator. Also we select
the right brand of the load cell in Type of the LOCEL setting
menu,if not setplease refer to Chapter four Menu set up
to do the related settings.
Manual
Auto
return select INPUTok
When you know the digital load cells adjustment coefficient,
you can use manual setting. This way is normally applied to
the situation when changing a new indicator and no need to
re-calibrate it with the weight. The detail operation can refer
to Chapter four, here we only introduce how to automatically
adjust the angel difference.
34
Presskey to chooseAutopressINPUTkey to enter LOCEL
quantity setting window.
Input area Input mode Note
Set value Number Can input 2 digit number maximum,
LOCEL quantity was limited within
116pcs
After input the Load cell quantity, pressINPUTkey to enter
weight loading operation, if u presskey, indicator will
back to the previous window:
Load the weight onside the instructed position of the platform,
after load for a while when stable, pressINPUTkey to enter
the LOCEL inner code window:
After ISN stable pressINPUTindicator will mention you to
enter the next weight loading status:
Load the weight circularly to finish the operationwhen reach
the regulated loading times,(loading times equals to the LOCEL
quantity which you set)pressINPUTkeyindicator will finish
the corner difference adjustment and return to the upper menu.
If you presskey during the corner difference operation
then the operation will be canceled and return to the upper
menu.
After finish the Angel adjustment, the indicator start to
calibrate, the details listed below:
7.2. Calibration
In standard setting windowpressto move the highlight
on to termIndicator calibrationpressINPUTto enter into
Calibration window.
First show you the division setting,
Quantity of LOCEL 123
Value8
(Input range116)
Return INPUTok
Load weight (01/08)
(load the weight onside the
instructed position of the
platform)
Return INPUTOK
Load weight (02/08)
(load the weight onside the
instructed position of the
platform)
Return INPUTOK
LOCEL ISN (01/08)
1998202
Return INPUTOK
Division 123
Value1
(1,2,5,10,20,50 optional)
Return INPUTOK
35
After the division setting pressINPUTto set the decimal
points
Input area Input Mode Note
Value Number Decimal points only accept the
input of 01234Other number
input will be error alerted.
After input the digit rates, pressINPUTto enter F.S settings,
Input area Input Mode Note
Value Number Allow to input 6 BITS number maximum
After input the F.S, pressINPUTto enter Zero confirm window,
Under no load status waiting for the A/D code stable then
pressINPUTindicator enter into load weight window.
Please load the standard weight, input the related weight value
and waiting for the A.D code getting stablethen pressINPUT
key to finish the calibration. Indicator will return to the
standard calibration window.
PressWeighingkey to return to the weighing mode. If the LOCEL
does not have the problem, you can get the accurate weight at
present. Please note if the AD code not drift too muchwe can
assume the AD code is stable.
Input area Input Mode Note
Value Number The divisions only accept the
input of 125102050Other
number input will be error
alerted
Input area Input Mode Note
Value Number Allow to input 6 BITS number maximum
Decimal points 123
Value3
(0,1,2,3,4 optional)
Return INPUTOK
F.S 123
Value200.000 kg
(Input the F.S value)
Return INPUTOK
Load weight200.000 kg 123
298568
Return INPUTOK
Zero (LOCEL A/D code)
1569
Return INPUTOK
Normally, after the above steps, indicator calibration was
finished!! Other measurement parameter should be following the
indicators default set. If you want special requirement, please
set accordingly refer to Chapter four.
36
Chapter 8 Communication
8.1Serial communication interface
XK3190DS2 weighing indicator can communicate in data with PC
through serial communication interface. The communication mode
includes continuous mode and command mode. In command mode one
PC can communicate with several indicators.
8.1.1 Connection:
. The communication interface is a 15 pin RS232 socket.
The signal of each pin is detailed in figure 7-1 (pin
6, 7, 8.for RS232C; pin 1, 2,3,4,8 for RS422C). The serial
communication shares the same socket with scoreboard.
. The 4-pin shield wire is recommended.
Figure (8-1) Serial communication output and scoreboard
interface
8.1.2 Signal parameter
. Signal: RS232/RS422/RS485
. Baud rate: 300/600/900/1200/2400/4800/9600
. Address: 26 (A ~ Z)
8.1.3. Continuous mode for serial communication
The data sent are the current weight which the indicator
shows(G.W or N.W)each frame including 12 group of data, the
format listed below:
N Related contents and the notes
1 02(XON) BEGIN
2 +/- SIGN
3 Weight information HIGH
N Related contents and the notes
Weight information
Weight information
8 Weight information LOW
9 Decimal points RIGHT TO LEFT04
10 XOR CALIBRATON 4 BITS HIGH
11 XOR CALIBRATION 4 BITS LOW
12 03(X0FF) END
Note
! Make sure that communication interface output lead and
computer are correctly connected, if there is something
wrong with connection, damage will happen to output port
of instrument and input port of computer, sometimes, the
damage is so big that instrument and, computer and
corresponding peripherals are got involved
! Necessary computer technology and programming expertise
are required for computer communication, which should be
participated and instructed by professionals.
Non-professional staff is supposed not to be involved in
this regard.
This connection way was only suitable for the factorys
communication protocolif the customers have their own special request, please set the wire according to chapter
ones detail!
37
XOR23 89
8.1.4. Command mode for serial communication
Indicator sends out the related data according to the upper
apparatus command. Each command sends out, indicator will send
one frame of data.
N Related contents and the notes
1 02XON Begin
2 AZ Address
3 AI Command AShaking hands
Command BRead gross weight
Command CRead tare
Command DRead net weight
Command EGet truck number
Command FGet goods number
Command GDelete all records
Command HZero
Command ITare
4 XOR Calibration High 4 bits
5 XOR Calibration Low 4 bits
6 03XOFF END
Output contents of the indicator
N Related contents and the notes
1 02XON Begin
2 AZ Address
3 AI Command AShaking hands
Command BOutputting gross weight
Command COutputting tare
Command DOutputting net weight
Command EOutputting truck number
Command FOutputting goods number
Command GNone
Command HNone
Command INone
4 Outputting proper data according to command
5 Outputting proper data according to command
6 Outputting proper data according to command
7 Outputting proper data according to command
8 Outputting proper data according to command
Outputting proper data according to command
Outputting proper data according to command
N-1 Outputting proper data according to command
N Outputting proper data according to command
N+1 XOR Calibration High 4 bits
N+2 XOR Calibration Low 4 bits
N+3 03XOFF END
The output contents (4n) Command A None Each frame including 6
sets of data
Command B Gross weight: Each frame including 14
sets of data 4 Sign (Positive or
negative) 511 Gross
Weight6 bits and 1 bit decimal
Command C Tare Each frame including 14 sets of data 4 Sign
(Positive or
negative) 511 Tare6 bits
and 1 bit decimal Command D Net weight Each frame including 14
sets of data 4 Sign (Positive or
negative)
38
511 Net Weight6 bits and 1 bit decimal
Command Outputting truck number 413: 10 Characters
Total output 16
characters Can including Chineseone Chinese take up two
characters, If truck number was less
than 10 characters, you
could use space to
compensate
Command Outputting goods number:
413: 10 Characters
Total output 16
characters Can including Chineseone Chinese take up two
characters, If goods number was less
than 10 characters, you
could use space to
compensate
XOR231011
NOTE. The definition of the higher or lower 4 bits for the
XOR calibration.
If the higher 4 or lower 4 bits for the XOR calibration is not
more than nine, you should add 30h and have it transmitted into
ASCII code. Otherwise, you should add 37h and have it
transmitted into alphabet ASCII code. For example, when the
higher 4 bits for the XOR calibration is 6, you can add 30h.
Obviously 36 will be transmitted as ASII code 6. Also, when
the higher 4 bits for the XOR calibration is B, you can add
37h, and 42h will be transmitted as ASCII code B
8.2 CONNECT INDICATOR WITH SCOREBOARD
8.2.1 The scoreboard interface adopts 15pin D type socket (share with the serial communication interface. (Ref. Figure
8-1, pin 9 and pin 10)
(This way was current loop output, and was the standard wire
connection after products were finished)
8.2.2 The current loop signal of the scoreboard is 20mA, output
is binary serial, and the baud rate is 600. Each frame of
date has 11 bits, including one initial bit (0), 8 data bits
(the lower one precedes the higher), one sign bit and one
stop bit.
8.2.3 A set of data is transmitted every 100ms, including 3
frames of data. (Ref. figure - 8-2).
Make sure that scoreboard and output leads are connected
correctly. If there is something wrong with connection,
damage will happen to output port of instrument and input
port of scoreboard, sometimes, the damage is so big to
influence the instrument and scoreboard. Only specially
provided connecting cable is allowed to be use.
39
Figure823 frame of data
Data of the first frame:
The sign bit is zero
X: D0, D1,D2 -------positions of decimal point (0-4)
Y: D3 ------------------weight sign (1-negative, 0-positive)
D4 ---------------------standby bit
G18-G16: ------data of the weight
Data of the second frame:
The sign bit is zero
G15~G8: data of the weight
Data of the third frame:
The sign bit is one
G7~G0: Data of the weight
G0~G18: 19 binary bits for the weight from lower to higher bit.
Chapter 9 Print and record operation
9.1 connect to the Printer
9.1.1 The printer interface is standard paralleled output and
adopts 25-pin RS232 socket. Hereunder is the definition of 25
pins socket. (Ref. figure 9-1)
(Figure 9-1) Printer signal
40
9.2 Save and print the weighing record
9.2.1Indicator allows the truck number and the goods number
to 10 characters (1 Chinese take up 2 characters). It can save
1000 truck number and 1000 goods number maximum.
9.2.2The indicator saves and prints data simultaneously.
Namely, while saving each full set of records, it will print
them out in the meantime. (If the PRINT SET is enabled.)
9.2.3. There are three methods for saving data.
i. Empty-truck saving fist, then full-truck saving. Or
full-truck saving first, then empty-truck saving. It
means a full set of records will be constituted through
saving twice.
ii. When weighing a full-truck and having the knowledge of
the tare previously, saving once is enough to constitute
a full set of records.
iii. When weighing the goods instead of the truck on-loaded,
saving once can usually constitute a full set of records.
9.2.4. Saving and printing procedures
In weighing mode, pressSAVE PRINTindicator enters the below window:
NotePrint function cannot be put into use until properly set.
1. The output lead of the printing interface in the indicator must
be connected to the printer accurately and only specially
provided printer connecting wire is allowed to be used.
Otherwise, the indicator output port and the printer input port
will be damaged, sometimes, the damage is so big that the
instrument and printer are got involved.
2. Before using the printer, please make sure that the cable is
correctly connected at first, and then turn on instrument, in
the end, power on printer. After printing, power off printer
at first, then turn off instrument, in the end, takes off the
cable. If the order is reversed, damage may happen to instrument
and printer.
3. Please choose the recommended printers, in that there are a
great variety of printers with different performances and
compatibilities.
4. Printer must be connected to ground; otherwise, damage will
happen to indicator and printer.
5. Printer signal earth is prohibited to be connected with the
power earth, otherwise will seriously damage the indicator as
well as the printer
In order to identify the three cases mentioned above, the
following assumptions are made in XK3190DS2 indicator:
1 If 0 is set for the truck number, it indicates that the
weighted is not a truck with goods, but the goods. Tare cannot
be set, it should be 0 only. The related truck number also cannot
be deleted, when indicator display or printing the truck number
will be shown as ----------
2 If the indicating light of TARE is on, it means the tare has
been informed. Therefore, saving once could constitute a full
set of records.
3 If the truck number is not zero, together with the indicating
light being off (In gross weight display mode), You need save
twice to constitute a full of set of records.
41
After input the vehicle No., please pressInputkey
The code was automatically get according to the vehicle No.,
if you do not input the vehicle No. before, you can input the
CODE here, then pressINPUTkey
After input the Cargo No.pressINPUTkey
The code was automatically get according to the Cargo No.,
if u do not input the Cargo no. before, you can input the CODE
here, then pressINPUTkeyindicator will save and print.
NOTE:
(1) When input area show highlight, it means you can input data
here. You can chose to input the data in Vehicle/cargo no. and
the CODE area.
(2If you input the data inside the area of Vehicle/cargo no.,
after pressINPUT, indicator will automatically check if any
related code existed inside the Ram. If yes, then indicator will
display the related code; if no, indicator will automatically
make and display a new code. If the user knew the code related
to vehicle/cargo no., you can directly input the code inside
the code area and the indicator will automatically check the
related vehicle /Cargo No. and display them, this can avoid the
relatively complex inputting. Vehicle/Cargo No. can be mix
inputted among English/PINYIN/Number, pressINPUT MODEkey can
switch the inputting mode. After finish the inputting inside
four areas, pressINPUT to save the record and getting print.
Input area Input Mode Note
Vehicle no Number/English/PI
NYIN/Sign
Maximum 10 characters1
Chinese take up 2 characters
Code (V) Number Maximum 3 bits number
Cargo no Number/English/PI
NYIN/Sign
Maximum 10 characters1
Chinese take up 2 characters
Code (C) Number Maximum 3 bits number
Input vehicle No./tare 123
Vehicle No.xxxx CODE1
Cargo No.--- CODE1
Return InputOK
Input vehicle No. /tare 123
Vehicle No.xxxx CODE1
Cargo No.--- CODE1
Return InputOK
Input vehicle No./tare 123
Vehicle No.xxxx CODE1
Cargo No.--- CODE1
Return InputOK
Input vehicle No./tare 123
Vehicle No.xxxx CODE1
Cargo No.--- CODE1
Return InputOK
42
If you presscan cancel the printing and return to the weighing
mode.
(3 Saving data could be set with or without Vehicle
number(detail set can refer to the Chapter Four). If you save
the data without the Vehicle No, then the Vehicle no. will be
Zero and cannot be changed.
4Saving data could be set with or without Cargo number(detail
set can refer to the Chapter Four). If you save the data without
the Cargo No, then the Cargo no. will be Zero and cannot be
changed.
5You can not save the record when weighing record unstable or GW0 or NW0.
9.2.5. Automatic saving and printing
1. The print setting for automatic saving is detailed
in PRINT SETTING section.
2. While automatic saving and printing, saving twice
mode does not exist.
3. When automatic saving, Vehicle number and goods
number saved are those set before.
4. Three conditions listed below for the value of
automatic saving:
. When the indicating light of TARE is on, the
current value will be saved into the set of
records.
. When the indicating light of TARE is off, the
indicator will automatically search its
memory for the right tare value corresponding
to the vehicle number and save it into the
set of records.
. When the indicating light of TARE is off and
the tare value corresponding to the vehicle
number does not exist, 0 would be saved as
the tare value in the set of records.
9.2.6. If the vehicle numbers are more than 1000, the indicator
will display RCD FUL!, you should delete some Vehicle number
or all the records refer to 8.3. If the records surpass 1000,
the indicator will delete the earliest one automatically.
9.3Examples for Print operation
9.3.1One time preset tare and print the weight bill
Step Situation Operation Display Note
1 Cargo
loaded
Press key
[tare
preset]
Preset tare
Setting
interface
2 Input
Preset
tare
E.g1000 Set value1.000 kg
3 pressINPUT Save value, preset tare
effective
4 press back to weighing mode
5 presssave print
Inputting
vehicle
no./cargo
no.
interface
6 Inputting
vehicle
No.
E.g.A1245 pressInputto save
Vehicle
No.A1245 If you want to
keep the
original
vehicle no.
please
directly
press
43
INPUT. 7 pressINPUT Enter CODE
area 8 Input
Vehicle
No. CODE
1If you do not input
the vehicle
NO.
Please input
the code.
2. If you
input the
vehicle No.
then no need
to input
code.
CODE1 1If you input the vehicle
No. the code
Will
automatically
got. Press
INPUT go to next step 2If you do not input the
vehicle
number,
please input
here.
9 pressINPUT Start to set the cargo
no.
10 Input
The
Cargo
number
E.g.Iron pressinputto save
Cargo No.Iron
If you want to
keep the
original
cargo
number,
please
directly
press
INPUT key 11 pressINPUT Enter CODE
area
12 Input
Cargo
No.
CODE
1If you do not input
the cargo
no. please
the code. 2 If you input the
cargo no.
then no
CODE0 1If you input the vehicle
No. the code
will
automatical
ly got.
Press
INPUT go to next
need to
input
code.
step 2If you do not input the
vehicle
number,
please input
here.
13 pressINPUT save the code
and start to
9.3.2 One time manual operation to print the weight bill Step Situation Operation Display Note
1 PressSAVE
Vehicle
No./Carg
o No.
Inputtin
g
Press the key in
the weighing
mode.
2 press
INPUT
No need to input
the vehicle
number,
directly press
theINPUTkey
to enter the
code area:
3 Input
vehicle
number zero
Inputting
0
Code0 Vehicle
No.0was
fitted to
express the
weight of the
goods, this
vehicle no.
44
cannot be
deleted
4 press
INPUT
Save the code
and entering
the cargo no.
setting
5 Input cargo
No.
E.g.:
steel
press
INPUTto
save
Cargo
No.:
steel
pressINPUTto
use original
cargo No.
6 press
INPUT
enter code
program
7 input cargo
No. code
1 input
code if
cargo No.
was not
inputted
2 skip
this step
if cargo
No. was
inputted
code0 1 code will be
generated
automatically
if the cargo No.
has been
inputted, press
INPUTto skip
2.Input code if
the cargo No.
was not inputted
8 press
INPUT
save the code,
start to print
weighing ticket
9.3.3 print weighing ticket(two storage method, loaded
vehicle after empty vehicle, or empty vehicle after loaded
vehicle)
step situation operation display Note
1 Prepare the
empty
vehicle(unti
l the stable
light on)
pressSAVE
input
vehicle
No./Cargo
No.
Press keys
on the
weighing
mode.
2 input new
vehicle No.
E.g.: A1245
pressINPUT
to save
vehicle
No.: A1245
press
INPUTto
use the
original
vehicle No.
3 pressINPUT enter code
program
4 input
vehicle No.
code
1.input code
if the
vehicle No.
has not been
inputted
2 skip this
step if the
vehicle No.
has been
inputted
code1 1 the code
will be
generated
automatica
lly if the
vehicle no.
has been
inputted,
press
INPUTto
skip
2Input the
code if the
vehicle No.
has not
been
inputted
45
5 pressINPUT save the
code, enter
cargo no.
setting
6 input cargo
no.
e.g.: steel
pressINPUT
to save
cargo no.:
steel
press
INPUTto
use the
original
cargo no.
7 pressINPUT enter code
program
8 input cargo
no. code
1 input code
if the cargo
no. has not
been
inputted
2skip this
step if the
cargo no. has
been
inputted
code 1 the code
will be
generated
automatica
lly if the
cargo no.
has been
inputted,
press
INPUTto
skip
2Input the
code if the
cargo no.
has not
been
inputted
9 pressINPUT the record
is not
save the
code,
complete,
please
complete!
return the
weighing
mode
10 Prepare the
loaded
vehicle(unti
l the stable
light on)
pressSAVE
input
vehicle
no./cargo
no.
display the
last
vehicle
no., cargo
no.
11 vehicle no.
input status
pressINPUT Skip
12 vehicle no.
code input
status
pressINPUT Skip
13 cargo no.
input status
pressINPUT Skip
14 cargo no.
code input
status
pressINPUT printing
now! pls
wait
press
INPUTto
print the
weighing
ticket
Note: the operation is the same when the empty vehicle are
weighed after the loaded vehicle
9.3.4 Auto-print the weighing ticket when tare is preset step situation operation display Note
1 follow the
operation
instructio
n of the
menu, set
the print
46
method to
be
auto-prin
t, press
weighto
return the
weighing
mode
2 Input the
preset tare e.g.100 Preset value
100 kg
3 press
INPUT save the
preset
value,
preset tare
is effected
4 press return the weighing
mode
5 prepare the
loaded
vehicle(unt
il the stable
light is on)
display
weight 400 kg
100 vehicle
weight
500,decrea
se tare100
6 Printing now!
please wait
auto-print
the
weighing
ticket when
the weight
is stable
9.3.5 Print weighing ticket use the tare according to vehicle
no.
step situation operation display Note
1 vehicle no.,
tare have
been preset
available
in the
indicator
2 bring the
loaded
vehicle(unti
l the stable
light is on)
Pre
Vehicle
No
Vehicle
no./tare
preset mode
display the
original
vehicle no.
and tare
3 input the
wanted
vehicle no.
e.g. A00123
press
INPUTto
save
Vehicle no.
A00123
if the
original
vehicle no.
matches,
press
TAREto
confirm
4 Press
INPUT
enter
vehicle no.
code
setting
5 input the
wanted
vehicle no.
code
Press
INPUT
1 if the
vehicle no.
has been
imputed,
press
INPUT
directly.
2 if the
47
vehicle no.
has not been
inputted,
then input
it here and
save by
pressing
INPUT
6 PressTARE return the
weighing
mode and
display the
net weight,
NW light on
the weight
after
decreasing
the tare
7 PressSAVE
input
vehicle
no./cargo
no.
press keys
in weighing
mode
8 input the new
vehicle no.
e.g.A1245
press
INPUTto
save
Vehicle
no. A1245
press
INPUTto
use the
original
vehicle no.
9 press
INPUT
enter code
setting
10 input the
vehicle no.
code
1 input
code if the
vehicle no.
has not been
inputted
code** 1 the code
will be
generated
automatical
ly if the
2 skip this
step if the
vehicle no.
has been
inputted
vehicle no.
has been
inputted,
press
INPUTto
skip
2 Input the
code if the
vehicle no.
has not been
inputted
11 press
INPUT
save the
code, enter
cargo no.
setting
12 Input cargo
no.
e.g.steel,
press
INPUTto
save
Cargo no.
steel
press
INPUTto
use the
original
cargo no.
13 press
INPUT
enter the
code
setting
14 input the
cargo no.
code
1 input the
code if the
cargo no.
has not been
inputted
2 skip this
step if the
code0 1 the code
will be
generated
automatical
ly if the
cargo no.
has been
48
cargo no.
has been
inputted
inputted,