Date post: | 05-Jul-2018 |
Category: |
Documents |
Upload: | dynamicsvt |
View: | 215 times |
Download: | 0 times |
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 1/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 2/78
Copyright © Huawei Technologies Co., Ltd. 2013. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees orrepresentations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 3/78
WCDMA RAN
DC-HSDPA Contents
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
i
Contents
1 Introduction ................................................................................................................................ 1-1
1.1 Scope ............................................................................................................................................ 1-1
1.2 Intended Audience......................................................................................................................... 1-1
1.3 Change History .............................................................................................................................. 1-1
2 Overview...................................................................................................................................... 2-1
3 Basic Principle ........................................................................................................................... 3-1
3.1 Overview ....................................................................................................................................... 3-1
3.2 DC-HSDPA Cells ........................................................................................................................... 3-2
3.2.1 Primary and Secondary Cells ............................................................................................... 3-2
3.2.2 DC-HSDPA Cell Groups ....................................................................................................... 3-3
3.3 Channel Mapping .......................................................................................................................... 3-4
3.3.1 Overview ............................................................................................................................... 3-4
3.3.2 HS-SCCH ............................................................................................................................. 3-4
3.3.3 HS-DPCCH ........................................................................................................................... 3-4
3.4 UE Categories ............................................................................................................................... 3-4
3.5 NodeB MAC-ehs ........................................................................................................................... 3-5
3.6 Impact on Interfaces ...................................................................................................................... 3-6
3.6.1 Overview ............................................................................................................................... 3-6
3.6.2 Impact on Iub ........................................................................................................................ 3-7
3.6.3 Impact on Uu ........................................................................................................................ 3-7
4 Technical Description .............................................................................................................. 4-1
4.1 Overview ....................................................................................................................................... 4-1
4.2 Radio Bearers ............................................................................................................................... 4-1
4.3 State Transition .............................................................................................................................. 4-2
4.4 Mobility Management .................................................................................................................... 4-2
4.4.1 Overview ............................................................................................................................... 4-2
4.4.2 Measurement Control ........................................................................................................... 4-2
4.4.3 Intra-Frequency Handover.................................................................................................... 4-3
4.4.4 Inter-Frequency Handover.................................................................................................... 4-3
4.4.5 Handover from a DC-HSDPA Cell to a Non-DC-HSDPA Cell............................................... 4-4
4.4.6 Handover from a Non-DC-HSDPA Cell to a DC-HSDPA Cell .............................................. 4-4
4.4.7 Inter-RAT Handover .............................................................................................................. 4-4
4.4.8 Handover Between RNC ...................................................................................................... 4-5
4.5 Load Control .................................................................................................................................. 4-5
4.5.1 RAB DRD ............................................................................................................................. 4-5
4.5.2 Call Admission Control ......................................................................................................... 4-9
4.5.3 Queuing and Preemption.................................................................................................... 4-10
4.5.4 Load Reshuffling and Overload Control ............................................................................. 4-10
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 4/78
WCDMA RAN
DC-HSDPA Contents
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
ii
4.6 Scheduling ................................................................................................................................... 4-10
4.7 Activating or Deactivating Secondary Cell .................................................................................. 4-11
5 Related Features ....................................................................................................................... 5-1
5.1 Features Related to DC-HSDPA ................................................................................................... 5-1
5.1.1 Prerequisite Features ........................................................................................................... 5-1
5.1.2 Mutually Exclusive Features ................................................................................................. 5-1
5.1.3 Impacted Features ................................................................................................................ 5-1
5.2 Features Related to Traffic-Based Activation and Deactivation of the Supplementary Carrier In
Multi-carrier ......................................................................................................................................... 5-2
5.2.1 Prerequisite Features ........................................................................................................... 5-2
5.2.2 Mutually Exclusive Features ................................................................................................. 5-2
5.2.3 Impacted Features ................................................................................................................ 5-2
6 Impact on the Network............................................................................................................. 6-1
6.1 DC-HSDPA .................................................................................................................................... 6-1
6.1.1 System Capacity ................................................................................................................... 6-1
6.1.2 Network Performance ........................................................................................................... 6-1
6.2 Traffic-Based Activation and Deactivation of the Supplementary Carrier In Multi-carrier ............. 6-1
6.2.1 System Capacity ................................................................................................................... 6-1
6.2.2 Network Performance ........................................................................................................... 6-1
7 Engineering Guidelines ........................................................................................................... 7-1
7.1 WRFD-010696 DC-HSDPA ........................................................................................................... 7-1
7.1.1 When to Use DC-HSDPA ..................................................................................................... 7-1
7.1.2 Required Information ............................................................................................................ 7-1
7.1.3 Hardware Planning ............................................................................................................... 7-2
7.1.4 Deployment .......................................................................................................................... 7-2
7.1.5 Performance Monitoring ....................................................................................................... 7-8
7.1.6 Parameter Optimization ........................................................................................................ 7-9
7.1.7 Troubleshooting .................................................................................................................... 7-9
7.2 WRFD-010713 Traffic-Based Activation and Deactivation of the Supplementary Carrier In
Multi-carrier ......................................................................................................................................... 7-9
7.2.1 When to Use Traffic-Based Activation and Deactivation of the Supplementary Carrier In
Multi-carrier .................................................................................................................................... 7-9
7.2.2 Information to Be Collected ................................................................................................ 7-10
7.2.3 Feature Deployment ........................................................................................................... 7-10
7.2.4 Feature Monitoring ............................................................................................................. 7-11
7.2.5 Troubleshooting .................................................................................................................. 7-11
8 Parameters.................................................................................................................................. 8-1
9 Counters ...................................................................................................................................... 9-1
10 Glossary .................................................................................................................................. 10-1
11 Reference Documents ......................................................................................................... 11-1
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 5/78
WCDMA RAN
DC-HSDPA Contents
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
iii
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 6/78
WCDMA RAN
DC-HSDPA 1 Introduction
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
1-1
1 Introduction
1.1 Scope
This document describes the feature Dual-Carrier High Speed Downlink Packet Access (WRFD-010696DC-HSDPA).
Before reading this document, you are advised to read the HSDPA Feature Parameter Description.
1.2 Intended Audience
This document is intended for:
Personnel who are familiar with WCDMA basics
Personnel who need to understand DC-HSDPA
Personnel who work with Huawei products
1.3 Change History
This section provides information on the changes in different document versions.
There are two types of changes, which are defined as follows:
Feature change: refers to the change in the DC-HSDPA feature.
Editorial change: refers to the change in wording or the addition of the information that was notdescribed in the earlier version.
Document Issues
The document issue is as follows:
04 (2013-06-20)
03 (2013-05-10)
02 (2012-07-20)
01 (2012-04-30)
Draft A (2012-02-15)
04 (2013-06-20)
This is the fourth commercial release for RAN14.0
Compared with Issue 03 (2013-05-10) of RAN14.0, Issue 04 (2013-06-20) includes the following
changes.
Change Type Change Description Parameter Change
Feature change None None
Editorial change Optimized section7.1.5 "Performance Monitoring." None
03 (2013-05-10)
This is the third commercial release of RAN14.0.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 7/78
WCDMA RAN
DC-HSDPA 1 Introduction
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
1-2
Compared with issue 02 (2012-07-20) of RAN14.0, this issue incorporates the changes described in thefollowing table.
Change Type Change Description Parameter Change
Feature change None None
Editorial change Optimized the following chapters and sections:
4.2 Radio Bearers
4.3 State Transition
4.4 Mobility Management
4.5 Load Control
6 Impact on the Network
7 Engineering Guidelines
None
Added the chapater 5 "Related Features." None
02 (2012-07-20)
This is the second commercial release of RAN14.0.
Compared with issue 01 (2012-04-30) of RAN14.0, this issue incorporates the changes described in thefollowing table.
Change Type Change Description Parameter Change
Feature change None. None.
Editorial change The following chapter is added: 6 "Impact on theNetwork."
None.
The engineering guideline about activating ordeactivating secondary cell is optimized. For details,see 7.2 "WRFD-010713 Traffic-Based Activation andDeactivation of the Supplementary Carrier InMulti-carrier."
None.
01 (2012-04-30)
This is the first commercial release of RAN14.0.
Compared with issue Draft A (2012-02-15) of RAN14.0, this issue incorporates the changes described inthe following table:
Change Type Change Description Parameter Change
Feature change None None
Editorial change The description about activating or deactivating secondary cellis optimized to improve readability. For details, see 4.7"Activating or Deactivating Secondary Cell."
None
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 8/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 9/78
WCDMA RAN
DC-HSDPA 2 Overview
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
2-1
2 Overview
Similar to Long Term Evolution (LTE), the HSPA technology is also influenced by the multi-carrieraggregations. The performance and throughput of HSPA can be improved by using more bandwidth
provided by multi-carriers. The throughput of end users can be double or more as compared withsingle-carrier HSPA.
In versions earlier than 3GPP Release 8, a UE used only a single carrier for HSDPA transmission. Theuse of a single carrier for HSDPA transmission is referred to as SC-HSDPA in this document.
3GPP Release 8 introduced DC-HSDPA. DC-HSDPA uses two adjacent carriers for the HSDPAtransmission of a UE, which doubles UE downlink throughput.
The requirements of DC-HSDPA are listed in Table 2-1.
Table 2-1 Requirements of the DC-HSDPA
Item Requirement
CN None
RNC The RNC needs to support downlink enhanced L2.
The RNC provides the radio bearer scheme for DC-HSDPA.
NodeB DC-HSDPA requires NodeB to support MAC-ehs. A single MAC-ehs entity supports HS-DSCHtransmission in more than one cell served by the same Node-B (FDD only).
UE In 3GPP Release 8, HS-DSCH UE categories 21, 22, 23, and 24 are added to supportDC-HSDPA. In 3GPP Release 9 or later, more HS-DSCH UE categories support DC-HSDPA.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 10/78
WCDMA RAN
DC-HSDPA 3 Basic Principle
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3-1
3 Basic Principle
3.1 Overview
DC-HSDPA allows a UE to set up HSDPA connections with two inter-frequency co-coverage cells. In thedownlink, the UE can simultaneously receive data over HS-DSCHs in the two cells. In the uplink, the UEusing the DCH or SC-HSUPA transmits data only in the primary cell. This document describes only theDC-HSDPA UEs whose uplink connections are established on the DCH or SC-HSUPA. For details aboutthe DC-HSDPA UEs whose uplink connections are established on the DC-HSUPA, see DC-HSUPAFeature Parameter Description.
Figure 3-1 shows an example of the uplink and downlink data transmission for a DC-HSDPA UE.
Figure 3-1 Example of the uplink and downlink data transmission for a DC-HSDPA UE
The two cells (primary cell and secondary cell) of DC-HSDPA follow the following restrictions:
The two cells belong to the same sector of a NodeB and are inter-frequency same-coverage cells.
The two cells are in the same downlink resource group of a NodeB.
The two cells operate on adjacent carriers with a frequency spacing less than or equal to 5 MHz in thesame frequency band.
The two cells have the same timing (Tcell).
The two cells support HSDPA and enhanced L2.
The two cells belong to the same operator.
The dual cell transmission only applies to HSDPA physical channels.
DC-HSDPA improves the throughput and delay of users in the whole cell even at the cell edge.Theoretically, DC-HSDPA with 64QAM provides a downlink peak data rate of 42 Mbit/s, which is twicethe peak rate provided by 64QAM.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 11/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 12/78
WCDMA RAN
DC-HSDPA 3 Basic Principle
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3-3
Figure 3-3 Primary and secondary cells configured with the same types of common channels
If the primary cell is configured with all the common channels shown in Figure 3-3, and if the secondarycell is configured with the HS-PDSCH, HS-SCCH, and P-CPICH, the secondary cell cannot provideservices for SC-HSDPA and R99 users. Currently, Huawei DC-HSDPA does not support suchconfigurations.
3.2.2 DC-HSDPA Cell Groups
DC-HSDPA requires two inter-frequency co-coverage cells. The two cells are configured in a DC-HSDPAcell group on the NodeB side as follows: Run the NodeB MML command ADD DLDUALCELLGRP toadd the two DC-HSDPA cells to the DC-HSDPA cell group.
The NodeB reports the information about cells in each DC-HSDPA cell group to the RNC over the Iubinterface. The RNC selects a primary cell and a secondary cell for a DC-HSDPA UE based on thereceived cell information. For details, see section 4.5.1 "RAB DRD."
NOTE
The Tcell parameter must be set to the same value for the cells of a DC-HSDPA group.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 13/78
WCDMA RAN
DC-HSDPA 3 Basic Principle
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3-4
3.3 Channel Mapping
3.3.1 Overview
Figure 3-4 Channel mapping of DC-HSDPA
A DC-HSDPA UE receives two HS-DSCH transport channels from two cells of the same NodeB. EachHS-DSCH is mapped to one HS-SCCH and several HS-PDSCH physical channels.
The dedicated physical control channels DPCCH and DPCH/F-DPCH in the uplink and downlink arecarried on the primary cell.
3.3.2 HS-SCCHIn versions earlier than 3GPP Release 8, a UE can monitor a maximum of four HS-SCCHs at the sametime, according to 3GPP TS 25.331. In DC-HSDPA cell group, the HS-SCCHs on the primary cell areindependent of those on the secondary cell. A UE can monitor a maximum of six HS-SCCHs at the sametime. In each cell, the UE can monitor a maximum of three HS-SCCHs at the same time.
There are three types of HS-SCCH, type 1 for common use, type 2 for HS-SCCH Less Operation, andtype 3 for MIMO. DC-HSDPA uses only HS-SCCH type 1. DC-HSDPA with HS-SCCH Less Operationuses HS-SCCH type 2.
HS-SCCH Less Operation applies only to the primary cell.
3.3.3 HS-DPCCHThe UE gives feedback on the CQIs and HARQ ACK/NACK about two cells on the HS-DPCCH channelto the primary cell. The HS-DPCCH uses a new frame format that enables it to carry CQI and HARQ ACK/NACK information of the two cells in a Transmission Time Interval (TTI).
3.4 UE Categories
In 3GPP Release 8, HS-DSCH UE categories 21, 22, 23, and 24 are added to support DC-HSDPA, aslisted in Table 3-1. In 3GPP Release 9 or later, more HS-DSCH UE categories support DC-HSDPA. Fordetails about HS-DSCH UE categories, see 3GPP TS 25.306.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 14/78
WCDMA RAN
DC-HSDPA 3 Basic Principle
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3-5
Table 3-1 FDD HS-DSCH physical layer categories 21 to 24
HS-DSCHCategory
MaximumNumber
ofHS-DSCHCodesReceived
MinimumInter-TTIInterval
MaximumNumber ofBits of an
HS-DSCHTransportBlockReceivedWithin
an HS-DSCHTTI
TotalNumberof Soft
ChannelBits
SupportedModulation Without
MIMOOperationor DualCellOperation
SupportedModulation
Simultaneous withMIMOOperationandWithoutDual CellOperation
SupportedModul
ationwithDualCellOperation
Category 21 15 1 23370 345600
- -
QPSK,16QAMCategory 22 15 1 27952 345600
Category 23 15 1 35280 518400 QPSK,16QAM,64Q AM
Category 24 15 1 42192 518400
When a UE does not use DC-HSDPA after accessing a DC-HSDPA cell, the RNC performs fallback onthe UE if the UE belongs to a certain HS-DSCH category. For details about HS-DSCH categories thatsupport fallback in such a circumstance, see 3GPP TS 25.331.
The peak rate can reach 42.192 Mbit/s (= 2 x TB_Size/TTI = 2 x 42192/2) at the MAC layer, supportedby the CN.
3.5 NodeB MAC-ehs
DC-HSDPA requires the NodeB to support MAC-ehs. A single MAC-ehs entity supports HS-DSCHtransmission in more than one cell served by the same NodeB (FDD only). Queues of a DC-HSDPA UEare common for the two cells. The scheduler in the NodeB arranges the data transmission of queues onthe two cells. DC-HSDPA transmissions can be regarded as independent transmissions over twoHS-DSCH channels. There will be a separate HARQ entity on each HS-DSCH channel, that is, oneHARQ process per TTI for single carrier transmission and two HARQ processes per TTI for dual carriertransmission.
MAC-ehs selects Transport Format and Resource Combination (TFRC) for the MAC-ehs Protocol DataUnits (PDUs) of each cell independently based on the available resources of the cells and the CQI
reported by the UE.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 15/78
WCDMA RAN
DC-HSDPA 3 Basic Principle
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3-6
Figure 3-5 MAC-ehs architecture
In a NodeB, two MAC-ehs PDUs can be scheduled at the same time. Figure 3-6 shows an example oftraffic flow to a DC-HSDPA UE.
Figure 3-6 Example of traffic flow to a DC-HSDPA UE
3.6 Impact on Interfaces
3.6.1 Overview
To support DC-HSDPA, new Information Elements (IEs) are added to signaling messages.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 16/78
WCDMA RAN
DC-HSDPA 3 Basic Principle
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
3-7
UEs and NodeBs can report their capacity of DC-HSDPA to the RNC through the Iub and Uu interfaces.The RNC instructs cells to set up or reconfigure radio links with DC-HSDPA through the Iub interface.The RNC instructs UEs to set up or reconfigure radio bearers with DC-HSDPA through the Uu interface.
3.6.2 Impact on Iub
When a cell receives the AUDIT REQUEST message or when a new cell is set up or a cell capability ischanged, the NodeB reports the cell capability to the RNC in Audit Response message or ResourceState Indication message
When a cell supports DC-HSDPA, the NodeB sets the Multi Cell Capability Info IE to Multi CellCapable for the cell in Audit Response and sends the message to the RNC.
If the cell is a primary serving cell, all the possible secondary serving cells in the same sector must belisted in the Possible Secondary Cell List IE.
When the RNC instructs a cell to set up a radio link with DC-HSDPA, the information of the secondaryserving cell is added to the Radio Link Setup procedure or Radio Link Addition procedure.
The Additional HS Cell Information RL Setup IE is added to the Radio Link SetupRequest/Response/Failure messages and Radio Link Addition Request/Response/Failure messages toindicate the usage of DC-HSDPA and associated parameters.
3.6.3 Impact on Uu
In the RRC CONNECTION REQUEST message, the Multi cell support IE is added to indicate the UEcapability of supporting multiple cells.
In the RRC Connection Setup Complete and UE Capability Information message, the Physical ChannelCapability IE is extended to indicate the UE capability of DC-HSDPA.
The Downlink secondary cell info FDD IE in the following signaling messages indicates the usage of
secondary serving cell and related parameters:
RRC CONNECTION SETUP
ACTIVE SET UPDATE
CELL UPDATE CONFIRM
PHYSICAL CHANNEL RECONFIGURATION
TRANSPORT CHANNEL RECONFIGURATION
RADIO BEARER RECONFIGURATION
RADIO BEARER RELEASE
RADIO BEARER SETUP
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 17/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-1
4 Technical Description
4.1 Overview
This document describes only the functions that are different from those of SC-HSDPA.
These functions are as follows:
Radio Bearers
State transition
Mobility management
Load control
Scheduling
For details about other functions, see the HSDPA Feature Parameter Description.
4.2 Radio BearersWhen the downlink transport channel HS-DSCH is selected for streaming or BE services or combinedservice with streaming or BE, DC-HSDPA can be applied. When there is only a CS service, PSconversational service, IMS signaling, or SRB signaling, DC-HSDPA is not applied because of smalltraffic volume. You need to configure DC-HSDPA on both the NodeB and RNC sides.
On the NodeB side
You must configure DC-HSDPA cells. For details about how to configure DC-HSDPA cells, see section3.2 "DC-HSDPA Cells."
On the RNC side
− Select CFG_HSDPA_DC_SWITCH in the RNC-level parameter CfgSwitch to enable services to be
carried on DC-HSDPA. The CfgSwitch parameter is in the SET UCORRMALGOSWITCH command.
− Select DC_HSDPA in the cell-level parameter HspaPlusSwitch to enable DC-HSDPA in the cell.The HspaPlusSwitch parameter is set in the ADD UCELLALGOSWITCH and MODUCELLALGOSWITCH commands.
− Set MIMO64QAMorDcHSDPASwitch in the SET UFRC command to DC_HSDPA to selectDC-HSDPA as the preferential HSPA+ technology for the cell.
The Continuous Packet Connectivity (CPC) function can be enabled in the DC-HSDPA cells with thefollowing limitations:
CPC DTX is applicable to primary cell only because there will be no uplink control channel for theDC-HSDPA UE on secondary cell
CPC HS-SCCH Less Operation is applicable to primary cell only and is not applicable to secondarycell.
CPC DRX for a DC-HSDPA UE on two carriers is similar to that for a UE on a single cell.
Only UEs complying with 3GPP Release 9 and later support DC-HSDPA+MIMO. Table 4-1 describes theimplementation of DC-HSDPA+MIMO in Huawei products. For details about DC-HSDPA+MIMO, seeHSPA Evolution Feature Parameter Description.
Table 4-1 Implementation of DC-HSDPA+MIMO in Huawei products
Version Implementation
Supports
DC-HSDPA+MIMO
Number of Cells
Supporting MIMO in a
Supports Simultaneous
Use of DC-HSDPA
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 18/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-2
DC-HSDPA Group and MIMO for UEs
RAN12.0 Yes 1 No
RAN13.0 Yes 2 Yes
RAN14.0 Yes 2 Yes
64QAM can be enabled in one or both cells in the DC-HSDPA cell group. DC-HSDPA and 64QAM canbe used at the same time. When both cells in a DC-HSDPA group have 64QAM enabled, the peakdownlink rate can reach 42 Mbit/s.
When a file is being downloaded, the TCP acknowledgement is sent in the uplink. The higher the rate ofdownload is, the larger the bandwidth is required in the uplink. If the download rate reaches up to 42Mbit/s, the uplink rate of TCP acknowledgement is much higher than 384 kbit/s, the highest supported bythe DCH. HSUPA bearer is required to provide high bandwidth in the uplink to transmit TCPacknowledgement without delay. The downlink rate of 42 Mbit/s per user can be supported only whenHSUPA is used.
4.3 State Transition
DC-HSDPA UEs only support the CELL_DCH state. After DC-HSDPA UEs transition to other states, theycannot be carried on DC-HSDPA. DC-HSDPA UEs can perform state transition only in the primary cell.
When a UE supporting DC-HSDPA transitions from the CELL_FACH, CELL_PCH, or URA_PCH state tothe CELL_DCH state, the RNC establishes a DC-HSDPA radio bearer (RB) for the UE. After the statetransition is complete, the RNC performs RAB DRD to select an appropriate DC-HSDPA group for theUE. For details, see section 4.5.1 "RAB DRD."
NOTE
DC-HSDPA RB refers to the HSDPA RB that has DC-HSDPA enabled.
The state transition trigger threshold for DC-HSDPA UEs is the same as that for SC-HSDPA UEs. Fordetails, see State Transition Feature Parameter Description.
4.4 Mobility Management
4.4.1 Overview
The introduction of DC-HSDPA has no impact on handover measurement triggering and handoverdecision processes. During a handover, however, the RNC needs to decide whether DC-HSDPA is usedafter the handover if the target cell supports DC-HSDPA, or whether non-DC-HSDPA is used after thehandover if the target cell does not support DC-HSDPA.
This section describes only the mobility management of DC-HSDPA. For other information abouthandover, see the Handover Feature Parameter Description.
4.4.2 Measurement Control
When DC-HSDPA is enabled, the RNC maintains the active set only in the primary cell.
The intra-frequency measurement control for DC-HSDPA UEs is the same as that for SC-HSDPA UEs.
DC-HSDPA UEs can perform inter-frequency measurement in the following modes:
Compressed mode
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 19/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-3
The inter-frequency measurement control for DC-HSDPA UEs in compressed mode is the same asthat for SC-HSDPA UEs in compressed mode.
Non-compressed mode
DC-HSDPA UEs perform inter-frequency measurement in non-compressed mode when all of the
following conditions are met:
− CMP_UU_ADJACENT_FREQ_CM_SWITCH in the CmpSwitch parameter for the SETUCORRMALGOSWITCH command is selected.
When CMP_UU_ADJACENT_FREQ_CM_SWITCH is selected, the UE can perform inter-frequencymeasurement in non-compressed mode on frequencies spaced less than or equal to 5 MHz from theoperating frequency of the UE. For a DC-HSDPA network, it is recommended that this switch beturned off, because the UE currently cannot report whether it is allowed to use the non-compressedmode for frequencies of neighboring cells within 5 MHz from the current frequency.
− The value of the following IE in the RRC CONNECTION SETUP COMPLETE message sent by theUE is TRUE: "UE radio access capability" IE > "Measurement capability" IE > "Adjacent frequencymeasurements without compressed mode" IE.
− If UEs are performing DC-HSDPA services, the UE performs inter-frequency measurement only inthe cells operating on the same frequency as the secondary cell and the frequency is spaced lessthan or equal to 5 MHz from the operating frequency of the current cell.
− If UEs are not performing DC-HSDPA services, the UE performs inter-frequency measurement in thecells that meet the following conditions:
The cells that operate on the same frequency at the same frequency band as the current cell.
The cells that operate on frequencies whose center frequencies are spaced less than or equal to 5MHz away from the center frequency of the current cell.
All cells to be measured operate on the same frequency.
4.4.3 Intra-Frequency Handover
When receiving a measurement report indicating that the signal quality of a DC-HSDPA cell is better thanthat of the serving cell (a DC-HSDPA cell), the RNC decides whether to perform a DC-HSDPA handoverto the target cell:
If the admission to the target cell is allowed and the radio link configuration is successful, the RNCperforms the handover.
If the admission to the target cell is allowed but the radio link configuration is unsuccessful, the RNCreconfigures the service on SC-HSDPA and then performs an SC-HSDPA handover.
If the admission to the target cell is not allowed, the RNC reconfigures the service on the DCH andperforms a DCH handover:
−
If the DCH handover is allowed, the RNC performs the handover.− Otherwise, the RNC does not perform the handover.
4.4.4 Inter-Frequency Handover
During an inter-frequency handover, the DC-HSDPA UE needs to measure the signal quality of theprimary cell and its neighboring cells. If the secondary cell is a neighboring cell of the primary cell, theDC-HSDPA UE also needs to measure the signal quality of the secondary cell. The inter-frequencyhandover process for DC-HSDPA UEs is the same as that for SC-HSDPA UEs. For details about theinter-frequency handover, see Handover Feature Parameter Description.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 20/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-4
4.4.5 Handover from a DC-HSDPA Cell to a Non-DC-HSDPA Cell
When receiving a measurement report from a DC-HSDPA UE indicating that the signal quality of aninter-frequency non-DC-HSDPA cell is better than that of the serving cell (a DC-HSDPA cell), the RNCinitiates an RB reconfiguration procedure to make the service be carried on the DCH or HSDPA andmeanwhile performs a handover.
When receiving a measurement report carrying the signal quality of intra-frequency non-DC-HSDPAcells, the RNC performs different operations in different scenarios. Details are as follows:
If an intra-frequency non-DC-HSDPA cell in the active set reports event 1D,
− The RNC initiates an RB reconfiguration procedure to make the service be carried on the DCH orHSDPA and meanwhile initiates a serving cell change procedure whenCMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH in the CmpSwitch parameter is selected.
− The RNC initiates an RB reconfiguration procedure to make the service be carried on the DCH orHSDPA and then initiates a serving cell change procedure whenCMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH in the CmpSwitch parameter is
deselected. If an intra-frequency non-DC-HSDPA cell outside the active set reports event 1D,
− The RNC initiates an RB reconfiguration procedure to make the service be carried on the DCH orHSDPA and then initiates an active set update procedure with serving cell change whenCMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH in the CmpSwitch parameter is selected.
− The RNC initiates an RB reconfiguration procedure to make the service be carried on the DCH orHSDPA, initiates an active set update procedure, and then initiates a serving cell change procedurewhen CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH in the CmpSwitch parameter isdeselected.
The CmpSwitch parameter is in the SET UCORRMALGOSWITCH command.
4.4.6 Handover from a Non-DC-HSDPA Cell to a DC-HSDPA Cell
When receiving a measurement report indicating that the signal quality of a DC-HSDPA cell is better thanthat of the serving cell (a non-HSDPA cell), the RNC performs a handover after which the HSPA+technologies supported by both the source cell and the target cell are used in the target cell. If suchHSPA+ technologies are ranked lower than some HSPA+ technologies supported by both the target celland the UE, the ChannelRetryHoTimerLen timer is started after the handover. When the timer expires,the RNC tries to reconfigure the traffic radio bearer (TRB) and signaling radio bearer (SRB) to enablethem to support the higher-ranked HSPA+ technologies. If the reconfiguration fails, the RNC starts theretry timer (ChannelRetryTimerLen ) for periodic retry attempts.
The HSPA+ technologies that can be retried are specified by the parameter RetryCapabil i ty in the SET
UFRC command.The ChannelRetryHoTimerLen and ChannelRetryTimerLen commands are set using the SETUCOIFTIMER command.
4.4.7 Inter-RAT Handover
The inter-RAT handover process for DC-HSDPA UEs is the same as that for SC-HSDPA UEs. For details
about the inter-RAT handover, see Handover Feature Parameter Description.
After a UE is handed over to a DC-HSDPA cell from a cell belonging to another RAT, the UE is carried on
the HSDPA. The RNC starts a retry timer as soon as the handover is complete. When the timer expires,
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 21/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-5
the RNC initiates an RB reconfiguration procedure to make the UE carried on the DC-HSDPA or a higher
HSPA+ technology. If the reconfiguration fails, the RNC starts the retry timer for periodic DRD.
The ChannelRetryTimerLen parameter in the SET UCOIFTIMER command specifies the retry timer.
4.4.8 Handover Between RNC
The current version does not support the handover between different RNCs for DC-HSDPA users.
During the handover, if the target cell is from different RNC, the DC-HSDPA user falls back to SC-HSDPAand then the handover is performed.
Upon completion of the handover, if DC-HSDPA is included in HSPA technologies that can be retried byUEs (that is, DC-HSDPA under the RetryCapabil i ty parameter is turned on) and the handover target cellsupports DC-HSDPA, the RNC will attempt to switch the services on DC-HSDPA RABs.
4.5 Load Control
4.5.1 RAB DRD
During the RAB setup or state transition from CELL_FACH to CELL_DCH, the RNC performs DRDs toselect a primary cell and a secondary cell for DC-HSDPA UEs. This section describes the DRD forDC-HSDPA UEs. For more details about DRD, see Directed Retry Decision Feature ParameterDescription.
DRD Procedure
Figure 4-1 outlines DRD procedure.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 22/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-6
Figure 4-1 DRD procedure
1. The RNC selects cells that meet the quality requirements of inter-frequency DRD as candidate cells.
For details about the quality requirements of inter-frequency DRD, see section "Inter-Frequency
DRD" in Directed Retry Decision Feature Parameter Description. 2. The RNC performs the following operations to select a cell from candidate cells as the primary cell.
When DRD for device type steering is enabled, the RNC selects the candidate cell with the highestdevice type steering priority as the primary cell and proceeds to step 3. If multiple candidate cells allhave the highest device type steering priority or if DRD for device type steering is disabled, proceedto step (b).
For details about how to select candidate cells based on device type steering, see section"Inter-Frequency DRD for Device Type Steering" in Directed Retry Decision Feature ParameterDescription.
(b) When DRD for HSPA+ technological satisfaction is enabled, the RNC selects the candidate cellwith the highest HSPA+ technological satisfaction as the primary cell and proceeds to step 3. If
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 23/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-7
multiple candidate cells all have the highest HSPA+ technological satisfaction or if DRD for HSPA+technological satisfaction is disabled, proceed to step (c).
For details about how to select candidate cells based on the HSPA+ technological satisfaction, seesection "Inter-Frequency DRD for Technological Satisfaction" in Directed Retry Decision Feature
Parameter Description. (c) When DRD for service steering is enabled, the RNC selects the candidate cell with the highestservice priority as the primary cell and proceeds to step 3. If multiple candidate cells all have thehighest service priority or if DRD for service steering is disabled, proceed to step (d).
For details about how to select candidate cells based on the service priority, see section "ServicePriority-based Cell Selection."
(d) When DRD for load balancing is enabled, the RNC selects the candidate cell with the lightestdownlink load based on downlink load balancing. For a DC-HSDPA cell, the RNC considers thedownlink load of the corresponding DC-HSDPA group, not the downlink load of the DC-HSDPA cell.Therefore, the RNC selects at least two cells in the same DC-HSDPA group as candidate cells. Then,the RNC selects the cell with the lightest load as the primary cell based on uplink load balancing andproceeds to step 3.
For details about how to select cells based on downlink load balancing, see "Downlink Load-basedCell Selection." For details about how to select cells based on uplink load balancing, see "UplinkLoad-based Cell Selection."
3. The RNC selects the other cell in the DC-HSDPA group to which the primary cell belongs as thesecondary cell. The DRD procedure is complete. Then, the RNC performs call admission control(CAC). For details, see section "Inter-Frequency DRD" in Directed Retry Decision Feature ParameterDescription.
NOTE
The HSPA technological satisfaction of DC-HSDPA cells is the same as that of SC-HSDPA cells. When all of the precedingDRD functions are disabled, the RNC instructs the UE to access the cell with the highest HSPA technological satisfaction.If the access fails, the RNC randomly selects a cell from candidate cells for the UE. If the cell supports DC-HSDPA, the
cell serves as the primary cell, and the other cell in the DC-HSDPA group serves as the secondary cell. If the cell does notsupport DC-HSDPA, the UE accesses the cell with the highest technology supported by the cell.
Service Priority-based Cell Selection
The service priority-based cell selection for DC-HSDPA UEs is the same as the target cell selection forSC-HSDPA UEs.
When multiple candidate cells support the same HSPA+ technologies, the RNC determines the servicepriorities of cells based on the uplink and downlink service bearers for the UE if DRD for service steeringis enabled. The RNC then ranks candidate cells according to service priority and selects the cell with thehighest service priority as the candidate cell.
The RNC uses HSDPA as the downlink service bearer for DC-HSDPA UEs.
If the requested service is combined services, the RNC uses the RAB with the highest priority for ranking.In addition, the selected cell must support all services in the combined services. For details about thepriority of a RAB, see Load Control Feature Parameter Description.
Table 4-2 lists the reference service priorities for different service bearers.
Table 4-2 Reference service priorities
UL and DL Service Bearers Reference Service Priority
DCH and DCH DCH service priority
DCH and HSDPA HSDPA service priority
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 24/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-8
UL and DL Service Bearers Reference Service Priority
DCH and DC-HSDPA HSDPA service priority
HSUPA and DCH HSUPA service priority
HSUPA and HSDPA HSDPA service priority and then HSUPA service priority
The HSDPA service priority is used first for the ranking. If the HSDPA servicepriority is not enough for the ranking, the HSUPA service priority is used.
HSUPA and DC-HSDPA
DC-HSUPA and DC-HSDPA
For details about how to select cells based on the service priority, see section "Inter-Frequency DRD forService Steering" in Directed Retry Decision Feature Parameter Description.
Downlink Load-based Cell Selection
The DRD for load balancing function for DC-HSDPA UEs is performed based on the number of powerresources available in the downlink and is basically the same as the downlink load balancing-basedDRD for SC-HSDPA UEs. The only difference is that the RNC considers the load of the DC-HSDPAgroup to which the candidate cell belongs when performing DRD based on load balancing forDC-HSDPA UEs.
For details about the downlink load balancing-based DRD, see section "Inter-Frequency DRD for LoadBalancing" in Directed Retry Decision Feature Parameter Description.
Uplink Load-based Cell Selection
DC-HSDPA UEs have uplink channels only in the primary cell. If a large number of DC-HSDPA UEs usea cell as the primary cell, the uplink load of the cell increases, and the uplink coverage deteriorates. The
uplink load-based cell selection function helps balance the uplink load between two carriers.
If the uplink load balancing switch ULLdbDRDSwitchDcHSDPA is set to OFF, the RNC randomlyselects a cell from candidate cells as the primary cell.
If this switch is set to ON, the RNC selects the cell with the lightest uplink load as the candidateprimary cell.
The RNC performs the uplink load balancing between candidate cells based on the equivalent number ofusers (ENUs) in the uplink.
The uplink load balancing-based DRD for DC-HSDPA is as follows:
1. If the UE initiates an RRC connection request in a non-candidate cell, the RNC selects the cell with
the lightest uplink load from candidate cells as the primary cell.2. In other circumstances, the RNC checks whether the remaining uplink ENUs of the current cell are
greater than the value of the ULLdbDRDLoadRemainThdDCHSDPA parameter.
If the remaining uplink ENUs of the current cell are greater than the value of theULLdbDRDLoadRemainThdDCHSDPA parameter, the RNC selects the current cell as the primarycell.
If the remaining uplink ENUs of the current cell are less than or equal to the value of theULLdbDRDLoadRemainThdDCHSDPA parameter, the RNC calculates the difference between theremaining uplink ENUs of the candidate primary cell and that of the current cell.
− If the difference is greater than the value of ULLdbDRDOffsetDcHSDPA , the RNC selects thecandidate primary cell as the primary cell.
− Otherwise, the RNC selects the current cell as the primary cell.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 25/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-9
After selecting the primary cell, the RNC selects the other cell in the same DC-HSDPA group as thesecondary cell.
4.5.2 Call Admission Control
Overview
In terms of Call Admission Control (CAC) based on the code resource, CE resource, or Iub resource,DC-HSDPA CAC is not changed, compared with SC-HSDPA CAC.
In terms of CAC based on the DL power or equivalent number of users (ENU), DC-HSDPA CAC ischanged, that is, the resources of the DC-HSDPA cell group need to be considered.
CAC Based on the DL Power
Figure 4-2 shows the resource allocation in the two cells of a DC-HSDPA cell group. In this figure, the DLpower is taken as an example.
Figure 4-2 DL power of a DC-HSDPA cell group
The variables in Figure 4-2 are described as follows:
Pmax: maximum DL power of a cell
Pnon-HSPA: DL power used for non-HSPA UEs in a cell
GBPSC-H: DL power required by the HS-PDSCHs to provide GBRs for SC-HSDPA UEs in a cell.
GBPDC-H: DL power required by the HS-PDSCHs to provide GBRs for the DC-HSDPA UEs in theDC-HSDPA cell group.
For a DC-HSDPA UE, the RNC performs CAC based on the total DL power margin of the DC-HSDPA cellgroup because the UE can use the DL power margin of any of the two cells after the admission.
For a non-DC-HSDPA UE, the RNC performs CAC based on the total DL power of the serving cell minusthe DL power used for the existing non-DC-HSDPA UEs in this cell. If the admission is successful, theRNC continues to perform the CAC based on the total DL power margin of the DC-HSDPA cell group.
CAC Based on the ENU
The CAC based on the Equivalent Number of Users (ENU) is similar to CAC based on the DL power.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 26/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 27/78
WCDMA RAN
DC-HSDPA 4 Technical Description
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
4-11
The calculation of the scheduling priority of a DC-HSDPA queue needs to consider different CQIs and Uurates of the two carriers. In the proportional fair (PF) algorithm and enhanced proportional fair (EPF)algorithm, R/r used for DC-HSDPA is different from that used for SC-HSDPA:
For SC-HSDPA, R represents the throughput corresponding to the CQI reported by the UE for this
carrier, and r represents the throughput currently achieved by the UE. A greater R/r value indicates ahigher scheduling priority.
For DC-HSDPA, R represents the throughput corresponding to the CQI reported by the UE for thiscarrier, and r represents the total throughput currently achieved by the UE on the two carriers. Agreater R/r value indicates a higher scheduling priority.
4.7 Activating or Deactivating Secondary Cell
This section describes the feature WRFD-010713 Traffic-Based Activation and Deactivation of theSupplementary Carrier In Multi-carrier.
The NodeB periodically monitors the traffic volume of a UE and decides whether to activate or deactivatethe secondary cell in the DC-HSDPA/DC-MIMO cell group through HS-SCCH order.
If the throughput at the MAC-ehs layer is lower than 100 kbit/s and the data in an MAC-ehs queue is80% likely to be completely sent within a short time, the NodeB instructs the UE to deactivate thesecondary cell.
If the throughput at the MAC-ehs layer is higher than 400 kbit/s and the data in an MAC-ehs queue is20% likely to be completely sent within a short time, the NodeB instructs the UE to activate thesecondary cell.
The preceding thresholds are not configurable.
The deactivation neither changes a DC-HSDPA cell to a non-DC-HSDPA cell nor changes the HS-DSCHUE category. After deactivation, the NodeB regards the UE as a SC-HSDPA UE, and after activation, the
NodeB regards the UE as a DC-HSDPA UE.
The function is controlled by the SECCELLACTDEASW switch in the NodeB MML command SETMACHSPARA.
The activation or deactivation is applicable to the UEs configured with DC-HSDPA, DC-MIMO, orDB-HSDPA in the downlink and to those configured with DCH or SC-HSUPA in the uplink. The function isnot applicable to DC-HSUPA because DC-HSUPA depends on DC-HSDPA.
The activation or deactivation of the UE takes effect after 12 timeslots when the UE receives theHS-SCCH order. The activation or deactivation of the NodeB takes effect immediately after the NodeBreceives an ACK of HS-SCCH order from the UE. If the NodeB receives an DTX from the UE, the NodeBretransmits or discards the HS-SCCH order.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 28/78
WCDMA RAN
DC-HSDPA 5 Related Features
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
5-1
5 Related Features
5.1 Features Related to DC-HSDPA
5.1.1 Prerequisite Features
WRFD-010610 HSDPA Introduction Package
WRFD-010629 DL 16QAM Modulation
WRFD-010685 Downlink Enhanced L2
DC-HSDPA must be enabled together with the WRFD-010683 Downlink 64QAM feature to provide thesingle-user downlink peak throughput of 42 Mbit/s.
For details about how to enable the HSDPA Introduction Package and DL 16QAM Modulation features,see chapter "Engineering Guidelines" in HSDPA Feature Parameter Description.
For details about how to enable the Downlink Enhanced L2 and Downlink 64QAM features, see HSPAEvolution Feature Parameter Description.
5.1.2 Mutually Exclusive Features
DC-HSDPA is mutually exclusive with the WRFD-021308 Extended Cell Coverage up to 200km feature.
5.1.3 Impacted Features
DC-HSDPA is affected by the following features:
WRFD-010617 VoIP over HSPA/HSPA+
− DC-HSDPA cannot be used for voice over IP (VoIP) services.
− DC-HSDPA can be used for VoIP services in VoIP+PS BE or VoIP+streaming combined services.
WRFD-010619 CS voice over HSPA/HSPA+
− DC-HSDPA cannot be used for CS services.
− DC-HSDPA can be used for CS services in CS+PS BE or CS+streaming combined services.
WRFD-020134 Push to Talk
− DC-HSDPA cannot be used for push to talk (PTT) services.
− DC-HSDPA can be used for PTT services in PTT+PS BE or PTT+streaming combined services.
DC-HSDPA affects the following features:
WRFD-140217 Inter-Frequency Load Balancing Based on Configurable Load Threshold
− When the number of DC-HSDPA UEs and their traffic volume are small, DC-HSDPA does not affectthe Inter-Frequency Load Balancing Based on Configurable Load Threshold feature.
− When the number of DC-HSDPA UEs and their traffic volume are large, the gain provided by theInter-Frequency Load Balancing Based on Configurable Load Threshold feature decreases.
NOTE
DC-HSDPA uses joint scheduling to balance the load across different carriers. The load balancing effect depends on thenumber of DC-HSDPA UEs and the traffic volume. When the number of DC-HSDPA UEs and the traffic volume are large,the load balancing effect is noticeable, but the gain provided by the Inter-Frequency Load Balancing Based onConfigurable Load Threshold feature decreases.
WRFD-140215 Dynamic Configuration of HSDPA CQI Feedback Period
DC-HSDPA can be used with the Dynamic Configuration of HSDPA CQI Feedback Period feature.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 29/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 30/78
WCDMA RAN
DC-HSDPA 6 Impact on the Network
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
6-1
6 Impact on the Network
6.1 DC-HSDPA
6.1.1 System Capacity
DC-HSDPA provides the following benefits:
Increases single-user downlink peak throughput. DC-HSDPA together with 64QAM pushes thesingle-user downlink peak throughput up to 42 Mbit/s.
Reduces the transmission delay of burst services and improves user experience.
DC-HSDPA UEs have the HS-DPCCH only in the primary cell, and therefore the uplink load of theprimary cell is slightly higher than that of SC-HSDPA cells.
DC-HSDPA UEs consume one channel element (CE) more than SC-HSDPA UEs.
6.1.2 Network Performance
DC-HSDPA affects cell uplink load and cell downlink load.
Impact on cell uplink load
Compared with SC-HSDPA UEs, DC-HSDPA UEs need to demodulate the signals in the primary andsecondary cells and need to report the feedback about both cells in the primary cell. The transmitpower of a DC-HSDPA UE on the HS-DPCCH is about 2 dB higher than that of SC-HSDPA UEs. Theuplink load of the primary cell is increased as a result.
Impact on cell downlink load
− For cells that have the same HSDPA service priority, DC-HSDPA does not significantly affect the
downlink load.− For cells that have different HSDPA service priorities, DC-HSDPA increases the downlink load of thecell with lower HSDPA service priority. The load increase is related to the proportion of UEssupporting DC-HSDPA and service model.
6.2 Traffic-Based Activation and Deactivation of theSupplementary Carrier In Multi-carrier
6.2.1 System Capacity
When there are a large number of multi-carrier HSDPA users (for example, DC-HSDPA users) anddownlink traffic is light, deactivating the supplementary carrier reduces uplink load in the cell served by
the primary carrier and increases the uplink capacity. This is demonstrated in the increase of the celluplink throughput or admitted number of users. For example, in a cell enabled with DC-HSDPA, theuplink load is reduced by 5% to 10% after the supplementary carrier is deactivated when the penetrationrate of DC-HSDPA users reaches 100%.
6.2.2 Network Performance
This feature deactivates the supplementary carrier for DC-HSDPA or DC-HSDPA+MIMO users with lowtraffic volume, reducing the radio resources available for these users. As a result, the service delay ofthese users may rise.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 31/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-1
7 Engineering Guidelines
7.1 WRFD-010696 DC-HSDPA
7.1.1 When to Use DC-HSDPA
DC-HSDPA is recommended for urban areas where at least two cells operate on frequencies at thesame frequency band and the spectrum resources are not limited.
In urban areas where the network capacity is not limited, DC-HSDPA provides more benefits if mostservices on the live network are burst services. Details are as follows:
Compared with SC-HSDPA, DC-HSDPA doubles the single-user throughput in the cell center and at thecell edge. DC-HSDPA also reduces the transmission delay and improves user experience. However,when the number of UEs performing data transmission increases, the downlink load increases, and as aresult the feature benefits in single-user throughput and cell throughput decrease.
DC-HSDPA can also be deployed in networks with limited capacity and high downlink load, but thefeature benefits are less noticeable.
DC-HSDPA is also recommended for suburban and rural areas where the network capacity is not limited.In such scenarios, DC-HSDPA increases the peak data rate for users and noticeably improves theexperience of users at cell edges.
7.1.2 Required Information
Before feature deployment, operators need to collect the following information:
Proportion of UEs supporting DC-HSDPA
A higher proportion of UEs supporting DC-HSDPA results in better system throughput gains.The VS.HSDPA.UE.Mean.CAT21.24 and VS.HSDPA.UE.Mean.CAT25.28 counters measure theaverage numbers of DC-HSDPA UEs.
Uplink capabilities
If dedicated channels (DCHs) are used in the uplink, the downlink peak rates for DC-HSDPA users arerestricted, resulting in decreased gains. HSUPA is recommended in the uplink for DC-HSDPA.
For details about how to check whether HSUPA is enabled in the uplink, see HSUPA FeatureParameter Description.
Bandwidth over the Iub interface
If the bandwidth over the Iub interface is inadequate, DC-HSDPA cannot yield notable gains. Anappropriate bandwidth is required over the Iub interface.
DC-HSDPA provides single-user downlink peak throughput of 42 Mbit/s. The minimum bandwidth overthe Iub interface is 50 M in IP transmission and is 55 M in ATM transmission considering the Iubtransmission efficiency. The actual bandwidth required over the Iub interface is greater than 50 Mbecause there are R99 users on the live network. The actual bandwidth required over the Iub interfacemust be calculated based on network planning and network optimization.
Packet loss rate on the core network
If the core network has a high packet loss rate, gains provided by DC-HSDPA decrease duringsingle-thread FTP sessions. An appropriate packet loss rate is required for the core network.
The recommended packet loss rate over the Iu interface is less than one of a million.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 32/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-2
Downlink cell load
If the downlink loads of cells in the same sector exceed 85% for most of the time, the benefits providedby DC-HSDPA may decrease.
The VS.MeanTCP counter measures the downlink load of a cell.
7.1.3 Hardware Planning
For 3900 series base station, BBU3900 needs to be configured with the WBBPb, WBBPd, or WBBPf.
For DBS3800 base station, the BBU3806 needs to be configured with the EBBC or EBBCd.
The BTS3812E or BTS3812AE needs to be configured with the EBBI, EDLP, or EDLPd board, and theUL baseband resources of DC-HSDPA cells cannot be carried on the HBBI or HULP board. They canbe carried on the EBBI, EULP, or EULPd board.
The BTS3902E supports DC-HSDPA.
Table 7-1 presents an example of the hardware configuration of a NodeB that is configured with three
sectors, with two carriers in each sector.
Table 7-1 Example of the hardware configuration of a NodeB that is configured with three sectors (with twocarriers in each sector)
Base Station Type Hardware Configuration
3900 series base stations The 3900 series base stations must be configuredwith a WBBPb/WBBPd/WBBPf board.
DBS3800 The DBS3800 must be configured with a EBBC orEBBCd board.
BTS3812E and BTS3812AE The BTS3812E and BTS3812AE must be configured
with an EDLP and an EULP/EULPd board. Alternatively, the BTS3812E and BTS3812AE mustbe configured with an EBBI board.
7.1.4 Deployment
This section describes how to activate, verify, and deactivate the optional feature WRFD-010696DC-HSDPA. This feature cannot be configured using the CME.
Requirements
Other Features
The cells to be enabled with DC-HSDPA must have the prerequisite features enabled. For detailsabout the prerequisites features for DC-HSDPA, see section 5.1.1 "Prerequisite Features."
License
The license "The number of Cells with DL DC function enabled" on the NodeB side has been activated.For details about the license items and how to activate the license, see License Management FeatureParameter Description.
Others
− One local cell can belong to only one DC-HSDPA group.
− The two DC-HSDPA cells must belong to the same baseband board.
− The two DC-HSDPA cells must belong to the same sector.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 33/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-3
− The two DC-HSDPA cells of a DC-HSDPA group are in the same downlink resource group of aNodeB.
− For distributed cells, two local cells in a DC-HSDPA cell group must belong to one RRU. Fornon-distributed cells, if two local cells in a DC-HSDPA cell group belong to two RRUs, the RRUs
adopt a star or chain topology.− The RNC software version is RAN12.0 or later.
− The NodeB software version is RAN12.0 or later.
− The difference between the values of the UARFCNDownlink parameters for the two cells must begreater than 19 and meanwhile less than or equal to 25.
− UEs must belong to HS-DSCH category 21 or higher. For details, see 3.4 "UE Categories."
Data Preparation
Table 7-2 list the data to prepare before activating DC-HSDPA.
Table 7-2 RNC data to prepare before activating DC-HSDPA
Parameter Name Parameter ID Setting Notes Data Source
NodeB ProtocolVersion
NodeBProtclVer It is recommended that thisparameter be set to R9.
Radio networkplan (internal)
CN domain ID CNDomainId Set this parameter to PS_DOMAIN.Radio networkplan (internal)
CN protocol version CNProtclVer It is recommended that thisparameter be set to R8.
Radio networkplan (internal)
Time Offset TCell All cells in the same sector that areto be enabled with DC-HSDPA
must have this parameter set to thesame value.
Radio network
plan (internal)
ChannelConfigurationStrategy Switch
CfgSwitch CFG_HSDPA_DC_SWITCH in theCfgSwitch parameter must beselected.
Radio networkplan (internal)
PreferredMIMO_64QAM orDC_HSDPACharacter
MIMO64QAMorDcH
SDPASwitch DC-HSDPA in theMIMO64QAMorDcHSDPASwitch parameter must be selected.
This parameter specifies prioritiesfor MIMO+64QAM and DC-HSDPA.
If the network supports bothMIMO+64QAM and DC-HSDPA,consult with the operator todetermine which technique takespriority. If the network load is heavy,set this parameter toMIMO+64QAM. Otherwise, set thisparameter to DC-HSDPA.
Radio networkplan (internal)
Service MappingStrategy Switch
MapSwitch If streaming services need to becarried on HSDPA,MAP_PS_STREAM_ON_HSDPA_ SWITCH in the MapSwitch
parameter must be selected.
Radio networkplan (internal)
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 34/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-4
Parameter Name Parameter ID Setting Notes Data Source
Cell Hspa Plusfunction switch
HspaPlusSwitch DC_HSDPA(Cell DC-HSDPAFunction Switch) andDL_L2ENHANCED(Cell DL
L2ENHANCED Function Switch) in the HspaPlusSwitch parametermust be selected.
Radio network
plan (internal)
HSPA TechnologiesRetried by UEs
RetryCapabil i ty When DRD needs to be enabled forDC-HSDPA UEs, DC_HSDPA inthe RetryCapabil i ty parametermust be selected.
Radio networkplan (internal)
Precautions
Activate this feature when the traffic volume in a cell is low. The reason is that the cell must be
deactivated before this feature is activated; after the cell is deactivated, the services in this cell areinterrupted.
Activation
Step 1 Change the NodeB's and CN's protocol versions to versions that support DC-HSDPA.
NOTE
3GPP Release 8 and later support DC-HSDPA. It is recommended that the NodeB's protocol version be set to Release 9and that the CN's protocol version be set to Release 8.
1. Run the RNC MML command MOD UNODEB to set NodeB Protocol Version to R9.
2. Run the RNC MML command MOD UCNNODE to set CN domain ID to PS_DOMAIN and set CN protocol version
to R8.
Step 2 Run the RNC MML command DEA UCELL multiple times to deactivate each logical cell of thecells to be enabled with DC-HSDPA.
Step 3 Run the NodeB MML command ADD DLDUALCELLGRP to add the cells to a DC-HSDPA cellgroup.
NOTE
Only the cells that meet the requirements described in section 3.2.2 "DC-HSDPA Cell Groups" can be added to aDC-HSDPA cell group.
Step 4 (Optional) Run the RNC MML command MOD UCELLSETUP to modify the value of the Time
Offset parameter based on the prepared data.
NOTE
Step 3 is required only when the value of the Time Offset parameter is inconsistent between DC-HSDPA cells. The valueof the Time Offset parameter can be queried using the LST UCELL command.
Step 5 Run the RNC MML command ACT UCELL multiple times to activate the cells in theDC-HSDPA cell group.
Step 6 Run the RNC MML command SET UCORRMALGOSWITCH to turn on the DC-HSDPAbearing switch by selecting CFG_HSDPA_DC_SWITCH in the Channel Configuration StrategySwitch parameter.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 35/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-5
Step 7 Run the RNC MML command SET UFRC to select DC-HSDPA as the preferential HSPA+technology by selecting DC_HSDPA in the Preferred MIMO_64QAM or DC_HSDPA Characterparameter.
NOTE
Select DC_HSDPA in the Preferred MIMO_64QAM or DC_HSDPA Character parameter before feature verification. Ifthe planned HSPA+ technology for a cell is not DC-HSDPA, select the planned HSPA+ technology as required afterfeature verification.
Step 8 (Optional) If streaming services need to use DC-HSDPA, run the RNC MML command SETUCORRMALGOSWITCH to select MAP_PS_STREAM_ON_HSDPA_SWITCH in the Service MappingStrategy Switch parameter.
Step 9 Run the RNC MML command MOD UCELLALGOSWITCH multiple times to enable DC-HSDPAby selecting DC_HSDPA(Cell DC-HSDPA Function Switch) in the Cell Hspa Plus functionswitch parameter.
Step 10 (Optional) When DC-HSDPA DRD is required, run the RNC MML command SET UFRC to
enable DC-HSDPA DRD by selecting DC_HSDPA in the HSPA Technologies Retried by UEs parameter.
----End
Activation Observation
Monitor counters or trace signaling to check whether DC-HSDPA is working properly.
Monitoring Counters
Monitor the value of the VS.HSDPA.RAB.DC.SuccEstab counter for DC-HSDPA cells. If the value of thiscounter is not zero for a DC-HSDPA cell, DC-HSDPA is working properly for that cell.
Tracing Signaling
Step 1 Click Uu Interface Trace on the LMT, as shown in Figure 7-1.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 36/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-6
Figure 7-1 Uu Interface Trace dialogue box
Step 2 For cells with Cell DC-HSDPA Function Switch turned on, trace RRC_RB_SETUP messageson the Uu interface.
Step 3 Perform dialing tests on FTP services for a UE to ensure that data is transmitted on HSDPAchannels.
Step 4 On the Trace tab page of the LMT, check whether RRC_RB_SETUP messages contain thedl-SecondaryCellInfoFDD information element.
If the dl-SecondaryCellInfoFDD information element is contained, as shown in Figure 7-2, it indicatesthat the feature is activated.
If the dl-SecondaryCellInfoFDD information element is not contained, it indicates that the feature is
not activated.
Figure 7-2 RRC_RB_SETUP message
----End
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 37/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-7
Deactivation
Step 1 Run the RNC MML command MOD UCELLALGOSWITCH to disable DC-HSDPA in a cell bydeselecting DC_HSDPA(Cell DC-HSDPA Function Switch) in the Cell Hspa Plus function switch parameter.
Step 2 Run the RNC MML command MOD UCELLALGOSWITCH to turn off the DC-HSDPA bearingswitch by deselecting CFG_HSDPA_DC_SWITCH in the Channel Configuration Strategy Switchparameter.
Step 3 Run the RNC MML command DEA UCELL to deactivate the logical cells of the localDC-HSDPA cells.
Step 4 Run the NodeB MML command RMV DLDUALCELLGRP to remove the DC-HSDPA cellgroup.
Step 5 Run the RNC MML command ACT UCELL to activate the cells that are deactivated in Step 3.
----End
MML Command Examples
//Modifying NodeB's and CN's protocol versions
MOD UNODEB: IDTYPE=BYID, NodeBId=1, NodeBProtclVer=R9;
MOD UCNNODE: CnOpIndex=0, CNId=0, CNDomainId=PS_DOMAIN, CNProtclVer=R8;
//Deactivating local cells
DEA UCELL: CellId=1;
DEA UCELL: CellId=2;
//Adding local cells to a DC-HSDPA cell group
ADD DLDUALCELLGRP: FIRSTLOCELL=1, SECONDLOCELL=2;
//Modifying the time offset parameter for a cell
MOD UCELLSETUP: CellId=1, TCell=CHIP512;
//Reactivating local cells
ACT UCELL: CellId=1;
ACT UCELL: CellId=2;
//Turning on the DC-HSDPA bearing switch
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_DC_SWITCH-1;
//Setting the preferential HSPA+ technology for a cell to DC-HSDPA
SET UFRC: MIMO64QAMorDcHSDPASwitch=DC_HSDPA;
//Setting the service mapping strategy switch
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-1;
//Turning on the DC-HSDPA switch for cells
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DC_HSDPA-1;
MOD UCELLALGOSWITCH: CellId=2, HspaPlusSwitch=DC_HSDPA-1;
//Enabling DC-HSDPA DRD
SET UFRC: RetryCapability=DC_HSDPA-1;
//Disabling DC-HSDPA
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DC_HSDPA-0;
MOD UCELLALGOSWITCH: CellId=2, HspaPlusSwitch=DC_HSDPA-0;
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_DC_SWITCH-0;
//Deactivating DC-HSDPA cells
DEA UCELL: CellId=1;
DEA UCELL: CellId=2;
//Removing DC-HSDPA celll group
RMV DLDUALCELLGRP: FIRSTLOCELL=1, SECONDLOCELL=2;
//Reactivating cells
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 38/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-8
ACT UCELL: CellId=1;
ACT UCELL: CellId=2;
7.1.5 Performance Monitoring
Monitoring Counters
To determine the number of DC-HSDPA radio access bearers (RABs) or DC-HSDPA users in a cell,check the values of the following RNC counters:
VS.HSDPA.RAB.DC.AttEstab: number of attempts to set up DC-HSDPA RABs on the primary carrierin the DC-HSDPA cell
VS.HSDPA.RAB.DC.SuccEstab: number of successful DC-HSDPA RAB setups on the primary carrierin the DC-HSDPA cell
VS.HSDPA.DC.PRIM.UE.Mean.Cell: average number of users that have chosen the current cell asthe primary cell
VS.HSDPA.DC.SEC.UE.Mean.Cell: average number of users that have chosen the current cell as thesecondary cell
To obtain the information about the scheduling of DC-HSDPA users under a NodeB, check the values ofthe following NodeB counters:
VS.HSDPA.DCCfg.AnchorCarrierActedNum: number of times during a measurement period that thecurrent cell has performed scheduling for users that are configured with DC-HSDPA and have chosenthe current cell as the primary cell, regardless of whether the secondary carrier has performedscheduling simultaneously. If the primary and secondary carriers have performed scheduling for auser simultaneously, only one time is counted.
VS.HSDPA.DCCfg.SupCarrierActedNum: number of times during a measurement period that thecurrent cell has performed scheduling for users that are configured with DC-HSDPA and have chosen
the current cell as the secondary cell, regardless of whether the primary carrier has performedscheduling at the same time. If the primary and secondary carriers have performed scheduling for auser simultaneously, only one time is counted.
VS.HSDPA.DCCfg.DualCarrierActedNum: number of times during a measurement period thatscheduling has been performed by the primary and secondary carriers at the same time for users thatare configured with DC-HSDPA and have chosen the current cell as the primary cell.
DC-HSDPA increases the cell throughput and peak rates for individual users. To determine the averageDC-HSDPA UE throughput, average cell HSDPA throughput, and total downlink throughput before andafter DC-HSDPA is deployed, check the values of the following counters:
VS.CellReserve.Counter3: This counter measures the amount of traffic that is correctly transmitted forDC-HSDPA/DC-HSDPA+MIMO UEs at the MAC-ehs layer. This counter is in units of kbit/s.
VS.CellReserve.Counter4: This counter measures the number of TTIs during whichDC-HSDPA/DC-HSDPA+MIMO buffer queues have data to transmit. If multiple queues have data totransmit in a TTI, the TTI number needs to be multiplied by the number of queues that have data totransmit. This counter is measured only on the primary carrier.
Use the following formula to calculate the average DC-HSDPA UE throughput at the base stationlevel:
VS.HSDPA.MeanChThroughput: an RNC counter that measures the average downlink throughput ofindividual MAC-d flows for HSDPA in the cell.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 39/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-9
The value of this counter is an average. The peak data rate per user can only be checked in drivetests.
VS.DataOutput.Mean: a NodeB counter that measures the average throughput at theMAC-hs/MAC-ehs layer in the cell during a measurement period.
Monitoring KPIs
The following cell-level KPIs indicate the performance of DC-HSDPA:
DC-HSDPA RAB Setup Failure Rate = 1 -(VS.HSDPA.RAB.DC.SuccEstab/VS.HSDPA.RAB.DC.AttEstab) x 100%
After DC-HSDPA is enabled, this KPI measures the DC-HSDPA RAB setup failure rate. If theDC-HSDPA RAB setup failure rate is much greater than the SC-HSDPA RAB setup failure rate, theproportion of UEs supporting DC-HSDPA may be very low or the DC-HSDPA traffic volume may bevery small. Under either condition, the value of the VS.HSDPA.RAB.DC.AttEstab counter is small.
When the proportion of UEs supporting DC-HSDPA is very low or the DC-HSDPA traffic volume isvery small, this KPI cannot indicate the actual DC-HSDPA RAB setup failure rate.
DC-HSDPA Call Drop Rate = VS.HSDPA.RAB.AbnormRel.DC/(VS.HSDPA.RAB.AbnormRel.DC+VS.HSDPA.RAB.NormRel.DC) x 100%
After DC-HSDPA is enabled, this KPI measures the DC-HSDPA call drop rate. If the DC-HSDPA calldrop rate is much greater than the SC-HSDPA call drop rate, the proportion of UEs supportingDC-HSDPA may be very low or the DC-HSDPA traffic volume may be very small. Under eithercondition, the value of the VS.HSDPA.RAB.DC.AttEstab counter is small.
When the proportion of UEs supporting DC-HSDPA is very low or the DC-HSDPA traffic volume isvery small, this KPI cannot indicate the actual DC-HSDPA call drop rate.
7.1.6 Parameter Optimization
N/A
7.1.7 Troubleshooting
Table 7-3 lists the alarms related to DC-HSDPA.
Table 7-3 Alarms related to DC-HSDPA
Alarm ID Alarm Name NE Feature ID Feature Name
ALM-28206 Local Cell Capability Decline NodeB WRFD-010696 DC-HSDPA
ALM-22221 UMTS Cell DC-HSDPAFunction Fault
RNC WRFD-010696 DC-HSDPA
7.2 WRFD-010713 Traffic-Based Activation and Deactivation ofthe Supplementary Carrier In Multi-carrier
7.2.1 When to Use Traffic-Based Activation and Deactivation of theSupplementary Carrier In Multi-carrier
This feature applies to all scenarios. This feature brings about the following benefits:
Reduced uplink load on the RAN side
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 40/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-10
Reduced UE power consumption in theory, depending on UE specifications.
This feature increases transmission delay of burst services for DC-HSDPA users, affecting userexperience. Therefore, you are advised to enable this feature on heavily loaded networks. For lightlyloaded networks, the operator can decide whether to use this feature as follows:
Disable this feature if the transmission delay of burst services needs to be reduced.
Enable this feature if UE power needs to be saved.
7.2.2 Information to Be Collected
Collect the following information before deploying this feature:
MC UE penetration rate
MC UEs include DC-HSDPA UEs and DC-HSDPA+MIMO UEs.
The larger the ratio of VS.HSDPA.DC.PRIM.UE.Mean.Cell to VS.HSDPA.UE.Mean.Cell, the moregains this feature brings.
Mean UE throughput
The smaller the value is for VS.HSDPA.MeanChThroughput, the more gains this feature brings.
7.2.3 Feature Deployment
This section describes how to activate, verify, and deactivate the optional feature WRFD-010713Traffic-Based Activation and Deactivation of the Supplementary Carrier In Multi-carrier.
Prerequisites
Dependencies on Hardware
This feature does not have any special requirements for hardware.
Dependencies on Other Features
WRFD-010696 DC-HSDPA
License
The license "the number of cells with traffic-based activation and deactivation of the slave carrierfunction enabled" on the NodeB side has been activated. For details about the license items and howto activate the license, see License Management Feature Parameter Description.
Other Prerequisites
The UE must be of HS-DSCH category 21, 22, 23, 24 to support DC-HSDPA or HS-DSCH category 25,26, 27, 28 to support DC-HSDPA+MIMO.
Activation ProcedureRun the NodeB MML command SET MACHSPARA (CME single configuration: NodeB ConfigurationExpress > IUB_NodeB > Radio Layer > Locell Algorithm Parameters > MAC Parameters >MACHSPARA; CME batch modification center: Modifying Physical NodeB Parameters in Batches) to setthe Mac-hs scheduling parameters with the DC HSDPA Cell Act Deact Switch set to ON(ON).
If the Mac-hs scheduling parameters of two DC-HSDPA cells must be set, set DC HSDPA Cell Act Deact Switch toON(ON) for each cell.
Verification Procedure
1. Run the NodeB MML command LST MACHSPARA to query the Mac-hs scheduling parameters.
Check whether the Secondary DC HSDPA Cell Act Deact Switch is turned on.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 41/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-11
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH. In this step, clearDRA_HSDPA_STATE_TRANS_SWITCH , DRA_HSUPA_STATE_TRANS_SWITCH , andDRA_PS_BE_STATE_TRANS_SWITCH from the Dynamic Resource Allocation Switch list.
3. Use a DC-HSDPA UE to perform PS services in a DC-HSDPA cell. Do not upload or download data
after required connections are established. Five seconds later, the UE becomes an SC UE, whichindicates that the feature has been activated.
Deactivation Procedure
Run the NodeB MML command SET MACHSPARA (CME single configuration: NodeB ConfigurationExpress > IUB_NodeB > Radio Layer > Locell Algorithm Parameters > MAC Parameters >MACHSPARA; CME batch modification center: Modifying Physical NodeB Parameters in Batches) to setthe Mac-hs scheduling parameters with the Secondary DC HSDPA Cell Act Deact Switch set toOFF(OFF).
Example
//Activation procedure
SET MACHSPARA: LOCELL=1, SECCELLACTDEASW=ON;
SET MACHSPARA: LOCELL=2, SECCELLACTDEASW=ON;
//Deactivation procedure
SET MACHSPARA: LOCELL=1, SECCELLACTDEASW=OFF;
SET MACHSPARA: LOCELL=2, SECCELLACTDEASW=OFF;
7.2.4 Feature Monitoring
The ratio of the throughput-based secondary cell active time over the user-existence time ofDC-HSDPA&DC-HSDPA+MIMO users can be monitored by the NodeB counterVS.HSDPA.DCCfg.SupCarrierDeact.TimeRatio .
For a single DC-HSDPA user, this function reduces the uplink load only by a limited degree. If there are alarge number of DC-HSDPA users, this function reduces the uplink load significantly. Follow these stepsto calculate the uplink load gain for a cell:
1. With this function disabled, obtain the value of VS.MinRTWP when the cell is idle and the value ofVS.MeanRTWP when some DC-HSDPA users are camping on the cell. Then, calculate thedifference between the values of VS.MinRTWP and VS.MeanRTWP and record it as RTWPoff .
2. With this function enabled, obtain the value of VS.MinRTWP when the cell is idle and the value ofVS.MeanRTWP when some DC-HSDPA users are camping on the cell. Then, calculate thedifference between the values of VS.MinRTWP and VS.MeanRTWP and record it as RTWPon.
3. Calculate the difference between the values of RTWPoff and RTWPon to obtain the uplink load gainyielded by this function.
The uplink load gain is easily affected by the number of DC-HSDPA users, the channel condition, andother users, and its absolute value is small. As a result, it is not easy to notice a stable uplink load gain.
7.2.5 Troubleshooting
Table 7-4 shows the alarms related to the feature.
Table 7-4 Alarm list
Alarm ID Alarm Name NE Feature ID Feature Name
22221 UMTS Cell DC-HSDPA FunctionFault
RNC WRFD-010713 Traffic-Based Activation and
Deactivation of the
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 42/78
WCDMA RAN
DC-HSDPA 7 Engineering Guidelines
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
7-12
Alarm ID Alarm Name NE Feature ID Feature Name
SupplementaryCarrier InMulti-carrier
28206 Local Cell Capability Decline NodeB WRFD-010713 Traffic-Based Activation andDeactivation of theSupplementaryCarrier InMulti-carrier
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 43/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 44/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-2
Parameter ID NE MML Command Feature ID Feature Name Description
UL 16QAM
DC-HSDPA
service.
7.
CFG_HSDPA_DC_SWITCH:When the switch is on, DCcan be configured for theHSDPA service.
8.CFG_HSDPA_MIMO_SWITCH: When the switch is on,MIMO can be configured forthe HSDPA service.
9.CFG_HSDPA_MIMO_WITH_
64QAM_SWITCH: When theswitch is on and the switchesfor 64QAM and MIMO are on,64QAM+MIMO can beconfigured for the HSDPAservice
10.CFG_HSPA_DTX_DRX_SWITCH: When the switch is on,DTX_DRX can be configuredfor the HSPA service.
11.CFG_HSPA_HSSCCH_LESS _OP_SWITCH: When theswitch is on, HS-SCCH LessOperation can be configuredfor the HSPA service.
12.CFG_HSUPA_16QAM_SWITCH: When the switch is on,16QAM can be configured forthe HSUPA service.
13.CFG_HSUPA_DC_SWITCH:When this switch is turned on,the DC-HSUPA function canbe enabled for HSUPAservices.
14.CFG_IMS_SUPPORT_SWITCH: When the switch is onand the IMS license isactivated, the BSC6900supports IMS signaling.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 45/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-3
Parameter ID NE MML Command Feature ID Feature Name Description
15.CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH:
Whether the UTRAN supportsthe function of lossless RLCPDU size change. When thisswitch is turned on, downlinkchannel reconfigurationbetween the DCH andHS-DSCH does not causeRLC PDU size change whichresults in packet loss. Thisfunction takes effect only onthe UEs enabled with thisfunction. For details about this
function, see 3GPP TS25.331.
16.CFG_LOSSLESS_RELOC_CFG_SWITCH: When theswitch is on and the UEsupports lossless relocation,the BSC6900 configureslossless relocation for PDCPparameters if therequirements of RLC mode,discard mode, and sequential
submission are met. Then,lossless relocation is used forthe UE.
17.CFG_MULTI_RAB_SWITCH:When the switch is on, theBSC6900 supportsmulti-RABs combinationssuch as 2CS, 2CS+1PS,1CS+2PS, and 2PS.
18.
CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH: Whenthe switch is on and the PDCPHeader compression licenseis activated, the PDCP headercompression algorithm forIPv6 is used at the BSC6900.
19.CFG_PDCP_RFC2507_HC_ SWITCH: When the switch ison and the PDCP Headercompression license isactivated, the PDCP
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 46/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-4
Parameter ID NE MML Command Feature ID Feature Name Description
RFC2507 headercompression algorithm is usedfor the BSC6900.
20.CFG_PDCP_RFC3095_HC_ SWITCH: When the switch ison and the PDCP ROHClicense is activated, the PDCPRFC3095 headercompression algorithm is usedfor the BSC6900.
21. CFG_PTT_SWITCH:When this switch is on, theBSC6900 identifies the PTT
user based on the QoSattributes in the RABassignment request message.Then, the PTT users aresubject to special processing.
22.CFG_RAB_REL_RMV_HSPAPLUS_SWITCH: When thisswitch is on and if the UE hasbeen configured with theHSPA(HSPA+) feature andother combined services, theUTRAN decides whether tofall back a certainHSPA(HSPA+) feature basedon the initial bearer policy ofthe other services whenreleasing a service. Thissaves network resources. TheHSPA(HSPA+) features areMIMO, 64QAM,MIMO+64QAM, UL 16QAM,DC-HSDPA, UL TTI 2ms, andDC-HSUPA.
GUI ValueRange:CFG_DC_MIMO_DYN AMIC_SELECT_SWITCH,CFG_DL_BLIND_DETECTION_SWITCH,CFG_EDPCCH_BOOSTING_ SWITCH,CFG_FREE_USER_SWITCH,CFG_HSDPA_64QAM_SWITCH,CFG_HSDPA_DCMIMO_SWITCH,
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 47/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-5
Parameter ID NE MML Command Feature ID Feature Name Description
CFG_HSDPA_DC_SWITCH,CFG_HSDPA_MIMO_SWITCH,
CFG_HSDPA_MIMO_WITH_ 64QAM_SWITCH,CFG_HSPA_DTX_DRX_SWITCH,CFG_HSPA_HSSCCH_LESS _OP_SWITCH,CFG_HSUPA_16QAM_SWITCH,CFG_HSUPA_DC_SWITCH,CFG_IMS_SUPPORT_SWITCH,CFG_LOSSLESS_DLRLC_P
DUSIZECHG_SWITCH,CFG_LOSSLESS_RELOC_CFG_SWITCH,CFG_MULTI_RAB_SWITCH,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,CFG_PDCP_RFC2507_HC_ SWITCH,CFG_PDCP_RFC3095_HC_ SWITCH,CFG_PTT_SWITCH,CFG_RAB_REL_RMV_HSPAPLUS_SWITCH
Actual ValueRange:CFG_DC_MIMO_DYN AMIC_SELECT_SWITCH,CFG_DL_BLIND_DETECTION_SWITCH,CFG_EDPCCH_BOOSTING_ SWITCH,CFG_FREE_USER_SWITCH,CFG_HSDPA_64QAM_SWITCH,
CFG_HSDPA_DCMIMO_SWITCH,CFG_HSDPA_DC_SWITCH,CFG_HSDPA_MIMO_SWITCH,CFG_HSDPA_MIMO_WITH_ 64QAM_SWITCH,CFG_HSPA_DTX_DRX_SWITCH,CFG_HSPA_HSSCCH_LESS _OP_SWITCH,CFG_HSUPA_16QAM_SWITCH,CFG_HSUPA_DC_SWITCH,
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 48/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-6
Parameter ID NE MML Command Feature ID Feature Name Description
CFG_IMS_SUPPORT_SWITCH,CFG_LOSSLESS_DLRLC_P
DUSIZECHG_SWITCH,CFG_LOSSLESS_RELOC_CFG_SWITCH,CFG_MULTI_RAB_SWITCH,CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,CFG_PDCP_RFC2507_HC_ SWITCH,CFG_PDCP_RFC3095_HC_ SWITCH,CFG_PTT_SWITCH,CFG_RAB_REL_RMV_HSPA
PLUS_SWITCHUnit:None
DefaultValue:CFG_DC_MIMO_DYN AMIC_SELECT_SWITCH-0&CFG_DL_BLIND_DETECTION_SWITCH-1&CFG_EDPCCH_BOOSTING_SWITCH-0&CFG_FREE_USER_SWITCH-0&CFG_HSDPA_64QAM_SWITCH-1&CFG_HSDPA_DCMI
MO_SWITCH-0&CFG_HSDP A_DC_SWITCH-0&CFG_HSDPA_MIMO_SWITCH-1&CFG _HSDPA_MIMO_WITH_64Q AM_SWITCH-0&CFG_HSPA_ DTX_DRX_SWITCH-0&CFG_ HSPA_HSSCCH_LESS_OP_ SWITCH-0&CFG_HSUPA_16QAM_SWITCH-0&CFG_HSUPA_DC_SWITCH-0&CFG_IMS_SUPPORT_SWITCH-1&CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH-0&CFG_ LOSSLESS_RELOC_CFG_SWITCH-0&CFG_MULTI_RAB _SWITCH-1&CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH-0&CFG_PDCP_RFC2507_HC_SWITCH-0&CFG_PDCP_RFC3095_HC_SWITCH-0&CFG_PTT_SWITCH-0&CFG _RAB_REL_RMV_HSPAPLUS_SWITCH-0
ChannelRetry BSC6900 SET WRFD-010 HSUPA 2ms TTI Meaning:This parameterspecifies the value of the
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 49/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-7
Parameter ID NE MML Command Feature ID Feature Name Description
HoTimerLen UCOIFTIMER 61403
WRFD-010
61404WRFD-010636
WRFD-010652
WRFD-010683
WRFD-010684
WRFD-010685
WRFD-010686
WRFD-010687
WRFD-021101
WRFD-021200
HSUPA2ms/10ms TTIHandover
SRB overHSUPA
SRB overHSDPA
Downlink64QAM
2x2 MIMO
DownlinkEnhanced L2
CPC - DTX /DRX
CPC -HS-SCCH lessoperation
DynamicChannelConfigurationControl (DCCC)
HCS(HierarchicalCell Structure)
channel retry handover timer.
When handover is performed
and some higher HSPA orHSPA plus technique issupported, UTRAN will triggerthe reconfiguration for thehigher techniques.
Pingpang will happen whenthe reconfiguration is triggeredimmediately when handoversucceeds, because handoverprocedure is frequently.
In order to avoid the pingpang,
this timer will start afterhandover procedure isperformed, and thereconfiguration will not betriggered until the timerexpires.
GUI Value Range:0~999
Actual Value Range:0~999
Unit:s
Default Value:2
ChannelRetryTimerLen
BSC6900 SETUCOIFTIMER
WRFD-01061008
WRFD-01061112
WRFD-01061206
WRFD-01061403
WRFD-010630
WRFD-010632
WRFD-010636
WRFD-010652
WRFD-010
Interactive andBackgroundTraffic Class onHSDPA
HSDPA DRD
Interactive andBackground
Traffic Class onHSUPA
HSUPA 2ms TTI
StreamingTraffic Class onHSDPA
StreamingTraffic Class onHSUPA
SRB over
Meaning:This parameterspecifies the value of thechannel retry timer. The timerwill start when traffic is set upor reconfigured and somehigher technique is notconfigured by some reasonexcept for the capability of UEor cell. Channel retry will beperformed after this timerexpires.
GUI Value Range:0~180
Actual Value Range:0~180
Unit:s
Default Value:5
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 50/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-8
Parameter ID NE MML Command Feature ID Feature Name Description
683
WRFD-010
684WRFD-010685
WRFD-010686
WRFD-010687
WRFD-021101
HSUPA
SRB over
HSDPADownlink64QAM
2x2 MIMO
DownlinkEnhanced L2
CPC - DTX /DRX
CPC -
HS-SCCH lessoperation
DynamicChannelConfigurationControl (DCCC)
CmpSwitch BSC6900 SETUCORRMALGOSWITCH
WRFD-01061006
WRFD-01061204
WRFD-020202
WRFD-020203
WRFD-021200
WRFD-010696
WRFD-010
202
HSDPA MobilityManagement
HSUPA MobilityManagement
Intra RNC SoftHandover
Inter RNC SoftHandover
HCS(HierarchicalCell Structure)
DC-HSDPA
UE State in
ConnectedMode(CELL-DCH,CELL-PCH,URA-PCH,CELL-FACH)
Meaning:1.CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH: Whenthe switch is on, the IMSsignaling assigned by the CNundergoes compatibilityprocessing as an ordinary PSservice. When the switch isnot on, no special processingis performed.
2.CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH:When the Iu QoS Negotiationfunction is active and theswitch is on, IE RAB
Asymmetry Indicator isSymmetric bidirectional, Theuplink and downlink"BSC6900" negotiation rate isasymmetric, "BSC6900"select the bigger rate as IuQoS negotiation rate. Whenthe switch is OFF, "BSC6900"select the less rate as Iu QoSnegotiation rate.
3.CMP_IU_SYSHOIN_CMP_IU
UP_FIXTO1_SWITCH: When
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 51/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-9
Parameter ID NE MML Command Feature ID Feature Name Description
the switch is on, the IUUPversion can be rolled back toR99 when complete
configurations are appliedduring inter-RAT handover.
4.CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH:When the switch is on, H2D isperformed before aneighboring "BSC6900" cellwhose version is earlier thanR5 is added to the active set;E2D is performed before aneighboring "BSC6900" cellwhose version is earlier thanR6 is added to the active set.If the DRNC is of a versionearlier than R5, DL servicescannot be mapped on theHS-DSCH. If the DRNC is of aversion earlier than R6, DLservices cannot be mappedon the HS-EDCH.
5.CMP_IUR_SHO_DIVCTRL_S
WITCH: When the switch ison, the diversity combinationover the Iur interface isconfigured on the basis of thatof the local "BSC6900". Whenthe switch is not on, thediversity combination over theIur interface is configured onthe basis of services. The flagof diversity combination overthe Iur interface can be set toMUST (for BE services) orMAY (for other services).
6.CMP_UU_ADJACENT_FREQ _CM_SWITCH: when theswitch is on, the "BSC6900"initiates the inter-frequencymeasurement withoutactivating the compressedmode if the following twoconditions are met: the UEsupports the non-compressedinter-frequency measurement,
the inter-frequency
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 52/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-10
Parameter ID NE MML Command Feature ID Feature Name Description
neighboring cells work in asame frequency which iswithin 5 MHz higher or lower
than the current frequency;when the switch is off, the"BSC6900" activates thecompressed mode beforeinitiating the inter-frequencymeasurement.
7.CMP_UU_AMR_DRD_HHO_ COMPAT_SWITCH: Thisparameter specifies to enable AMR through DRD two-stepprocedure function. WhenSRB is set up on DCH, and"BSC6900" decides to setupthe AMR through DRDprocedure, When the switch isenabled, "BSC6900" willexecute blind handover to thetarget cell, and then setup the AMR RBs on the target cell,When the switch is disabled,"BSC6900" will setup the AMRRBs on the target cell directly.
8.CMP_UU_AMR_SID_MUST_ CFG_SWITCH: Fornarrowband AMR services,when the switch is on, the SIDframe is always configured;when the switch is not on, theSID frame is configured on thebasis of CN assignment.
9.CMP_UU_FDPCH_COMPAT _SWITCH: When the switch is
OFF, if the informationelement that indicates theF-DPCH capability of UEexists in the message"RRC_CONNECT_REQ" or"RRC_CONNECT_SETUP_CMP", the F-DPCH capabilitydepends on that indicator. Inother case, it means UE doesnot support F-DPCH. Whenthe switch is ON, if theinformation element that
indicates the F-DPCH
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 53/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-11
Parameter ID NE MML Command Feature ID Feature Name Description
capability of UE exists in themessage"RRC_CONNECT_REQ" or
"RRC_CONNECT_SETUP_CMP", the F-DPCH capabilitydepends on that indicator. Ifthat information element doesnot exist, UE supportsF-DPCH when all theconditions meets: a) theversion of UE is Release 6. b)UE supports HS-PDSCH.
10.CMP_UU_IGNORE_UE_RLC _CAP_SWITCH: When theswitch is on, the RABassignment request and thesubsequent RB setupprocedure proceed if the RLC AM capabilities of the UE failto meet the minimum RLCTX/RX window bufferrequirement of the RAB to besetup. When the switch is noton, the RAB assignmentrequest is rejected.
11.CMP_UU_INTRA_FREQ_MC _BESTCELL_CIO_SWITCH:When this switch is on, thecell individual offset (CIO) ofthe best cell is always set to 0in the INTRA-FREQUENCYMEASUREMENT CONTROLmessages. Otherwise, theCIO information of the bestcell is not carried in theINTRA-FREQUENCYMEASUREMENT CONTROLmessages.
12.CMP_UU_IOS_CELL_SYNC _INFO_REPORT_SWITCH:When the switch is on, the cellsynchronization informationtraced by the IOS need to bereported during the RRCmeasurement period.
13.CMP_UU_SERV_CELL_CHG _WITH_ASU_SWITCH: When
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 54/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-12
Parameter ID NE MML Command Feature ID Feature Name Description
the switch is on, the active setupdate is in the sameprocedure as the change of
the serving cell. When theswitch is not on, the servingcell is changed after the UEupdates the active set anddelivers reconfiguration ofphysical channels. This switchis applicable only to R6 orabove UEs.
14.CMP_UU_SERV_CELL_CHG _WITH_RB_MOD_SWITCH:When the switch is on,channel transition is in thesame procedure as thechange of the serving cell.When the switch is not on, theserving cell is changed afterthe UE performs channeltransition and deliversreconfiguration of physicalchannels.
15.CMP_UU_VOIP_UP_PROC_
AS_NORMAL_PS_SWITCH:By default, the switch is on. Inthis case, the Alternative E-bitis not configured for L2.
16.CMP_F2F_RLC_ONESIDE_ REBUILD_SWITCH: Whenthe switch is set to ON, onlyuplink RLC or downlink RLCcan be re-established duringthe state transition fromCELL_FACH to CELL_FACH
(F2F for short).
17.CMP_D2F_RLC_ONESIDE_ REBUILD_SWITCH: Whenthe switch is set to ON, onlyuplink RLC or downlink RLCcan be re-established duringthe state transition fromCELL_DCH to CELL_FACH(D2F for short).
18.
CMP_RAB_5_CFG_ROHC_S
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 55/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-13
Parameter ID NE MML Command Feature ID Feature Name Description
WITCH: When the switch isset to ON, the service withRAB ID 5 can be configured
with the Robust HeaderCompression (ROHC)function. When the switch isset to OFF, the service withRAB ID 5 cannot beconfigured with the ROHCfunction.
19.CMP_RAB_6_CFG_ROHC_SWITCH: When the switch isset to ON, the service withRAB ID 6 can be configuredwith the ROHC function.When the switch is set to OFF,the service with RAB ID 6cannot be configured with theROHC function.
20.CMP_RAB_7_CFG_ROHC_SWITCH: When the switch isset to ON, the service withRAB ID 7 can be configuredwith the ROHC function.
When the switch is set to OFF,the service with RAB ID 7cannot be configured with theROHC function.
21.CMP_RAB_8_CFG_ROHC_SWITCH: When the switch isset to ON, the service withRAB ID 8 can be configuredwith the ROHC function.When the switch is set to OFF,the service with RAB ID 8
cannot be configured with theROHC function.
22.CMP_RAB_9_CFG_ROHC_SWITCH: When the switch isset to ON, the service withRAB ID 9 can be configuredwith the ROHC function.When the switch is set to OFF,the service with RAB ID 9cannot be configured with theROHC function.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 56/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-14
Parameter ID NE MML Command Feature ID Feature Name Description
23.CMP_HSUPA_MACD_FLOW _MUL_SWITCH: When the
switch is set to ON, MAC-dflow can be multiplexedwithout any restrictions. Whenthe switch is set to OFF, onlyMAC-d flows whosescheduling priority is lowerthan that of the current MAC-dflow can be multiplexed.
24.CMP_SMLC_RSLT_MODE_TYPE_SWITCH: If the ClientType of a positioning requestis Value Added Service orLawful Intercept Client, thepositioning result is reportedby using the Ellipsoid Arctype. For other client types,the positioning result isreported by using the Ellipsoidpoint with uncertainty circletype.
25.CMP_F2P_PROCESS_OPTI
MIZATION_SWITCH: Switchfor optimizing the procedurefor theCELL_FACH-to-CELL_PCH-or-URA_PCH state transition.When this switch is turned on,the algorithm for optimizingthe procedure for theCELL_FACH-to-CELL_PCH-or-URA_PCH state transition isactivated.
26.
CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH: Whetherto carry parameters related toevents 1A and 1D in systeminformation block type 11 (SIB11) and SIB 12. If the switch ofdeferred measurement controlreading is turned on, the UEcannot promptly readparameters related to events1A and 1D for intra-frequencyneighboring cells from SIB 11
or SIB12. As a result, the UE
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 57/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 58/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-16
Parameter ID NE MML Command Feature ID Feature Name Description
WITCH,CMP_RAB_9_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW _MUL_SWITCH,CMP_SMLC_RSLT_MODE_TYPE_SWITCH
Actual ValueRange:CMP_IU_IMS_PROC_ AS_NORMAL_PS_SWITCH,CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,CMP_IUR_SHO_DIVCTRL_SWITCH,CMP_UU_ADJACENT_FREQ _CM_SWITCH,CMP_UU_AMR_DRD_HHO_ COMPAT_SWITCH,CMP_UU_AMR_SID_MUST_ CFG_SWITCH,CMP_UU_FDPCH_COMPAT _SWITCH,CMP_UU_IGNORE_UE_RLC
_CAP_SWITCH,CMP_UU_INTRA_FREQ_MC _BESTCELL_CIO_SWITCH,CMP_UU_IOS_CELL_SYNC _INFO_REPORT_SWITCH,CMP_UU_SERV_CELL_CHG _WITH_ASU_SWITCH,CMP_UU_SERV_CELL_CHG _WITH_RB_MOD_SWITCH,CMP_UU_VOIP_UP_PROC_ AS_NORMAL_PS_SWITCH,CMP_F2F_RLC_ONESIDE_
REBUILD_SWITCH,CMP_D2F_RLC_ONESIDE_ REBUILD_SWITCH,CMP_RAB_5_CFG_ROHC_SWITCH,CMP_RAB_6_CFG_ROHC_SWITCH,CMP_RAB_7_CFG_ROHC_SWITCH,CMP_RAB_8_CFG_ROHC_SWITCH,CMP_RAB_9_CFG_ROHC_SWITCH,CMP_HSUPA_MACD_FLOW
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 59/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-17
Parameter ID NE MML Command Feature ID Feature Name Description
_MUL_SWITCH,CMP_SMLC_RSLT_MODE_TYPE_SWITCH,
CMP_F2P_PROCESS_OPTIMIZATION_SWITCH,CMP_UU_SIB11_SIB12_WITH_1A1D_SWITCH
Unit:None
DefaultValue:CMP_IU_IMS_PROC_ AS_NORMAL_PS_SWITCH-0&CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH-0&CMP_IU_SYSHOIN_CMP_
IUUP_FIXTO1_SWITCH-0&CMP_IUR_H2D_FOR_LOWR5 _NRNCCELL_SWITCH-0&CMP_IUR_SHO_DIVCTRL_SWITCH-0&CMP_UU_ADJACENT_FREQ_CM_SWITCH-0&CMP_UU_AMR_DRD_HHO _COMPAT_SWITCH-1&CMP _UU_AMR_SID_MUST_CFG _SWITCH-0&CMP_UU_FDPCH_COMPAT_SWITCH-0&CMP_UU_IGNORE_UE_RLC_
CAP_SWITCH-1&CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH-0&CMP_UU _IOS_CELL_SYNC_INFO_REPORT_SWITCH-0&CMP_UU_SERV_CELL_CHG_WITH _ASU_SWITCH-0&CMP_UU _SERV_CELL_CHG_WITH_ RB_MOD_SWITCH-1&CMP_ UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH-1&CMP_F2P_PROCESS_OPTIMIZ ATION_SWITCH-0&CMP_UU _SIB11_SIB12_WITH_1A1D_ SWITCH-0&CMP_F2F_RLC_ ONESIDE_REBUILD_SWITCH-0&CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH-0&CMP_RAB_5_CFG_ROHC_SWITCH-0&CMP_RAB_6_CFG_ROHC_SWITCH-0&CMP_ RAB_7_CFG_ROHC_SWITCH-0&CMP_RAB_8_CFG_ROHC_SWITCH-0&CMP_RAB_ 9_CFG_ROHC_SWITCH-0&
CMP_HSUPA_MACD_FLOW
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 60/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-18
Parameter ID NE MML Command Feature ID Feature Name Description
_MUL_SWITCH-0&CMP_SMLC_RSLT_MODE_TYPE_SWITCH-0
CNDomainId BSC6900 ADD UCNNODE
MOD UCNNODE
WRFD-010101
WRFD-021101
MRFD-211502
WRFD-021311
WRFD-040202
3GPP R9Specifications
DynamicChannelConfigurationControl (DCCC)
IP-Based BSCand RNCCo-Transmission on MBSC Side
MOCNIntroductionPackage
RNC NodeRedundancy
Meaning:Identifying the typeof a CN.
GUI ValueRange:CS_DOMAIN,PS_DOMAIN
Actual ValueRange:CS_DOMAIN,PS_DOMAIN
Unit:None
Default Value:None
CNProtclVer BSC6900 ADD UCNNODE
MOD UCNNODE
WRFD-010101
3GPP R9Specifications
Meaning:Protocol versionsupported by the CN. Thisparameter is modified basedon the actual protocol version
of the CN when the CNprotocol version upgrade,otherwise it will cause somefeatures supported by the newprotocol version unavailable.
GUI Value Range:R99, R4,R5, R6, R7, R8
Actual Value Range:R99, R4,R5, R6, R7, R8
Unit:None
Default Value:None
HspaPlusSwitch
BSC6900 ADDUCELLALGOSWITCH
MODUCELLALGOSWITCH
WRFD-010685
WRFD-010688
WRFD-010683
WRFD-010684
DownlinkEnhanced L2
DownlinkEnhancedCELL_FACH
Downlink64QAM
2x2 MIMO
Meaning:This parameter isused to select a featurerelated to HSPA+. If a featureis selected, it indicates thatthe corresponding algorithm isenabled. If a feature is notselected, it indicates that thecorresponding algorithm isdisabled. Note that otherfactors such as license and
the physical capability of
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 61/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-19
Parameter ID NE MML Command Feature ID Feature Name Description
WRFD-010686
WRFD-010687
WRFD-010702
WRFD-010693
WRFD-010694
WRFD-010695
WRFD-010696
WRFD-010697
WRFD-010699
CPC - DTX /DRX
CPC -HS-SCCH lessoperation
Enhanced DRX
DL64QAM+MIMO
UL 16QAM
UL Layer 2Improvement
DC-HSDPAE-DPCCHBoosting
DC-HSDPA+MIMO
NodeB restrict whether afeature can be used even ifthis feature is selected. The
EFACH/MIMO switchdetermines whether the cellsupports the E-FACH/MIMOfeature but does not affect theestablishment of the E-FACHand the MIMO cell.
GUI ValueRange:64QAM(Cell 64QAMFunction Switch), MIMO(CellMIMO Function Switch),E_FACH(Cell E_FACHFunction Switch),DTX_DRX(Cell DTX_DRXFunction Switch),HS_SCCH_LESS_OPERATION(Cell HS_SCCH LESSOPERATION FunctionSwitch),DL_L2ENHANCED(Cell DLL2ENHANCED FunctionSwitch), 64QAM_MIMO(Cell64QAM+MIMO FunctionSwitch), UL_16QAM(Cell UL16QAM Function Switch),
DC_HSDPA(Cell DC-HSDPAFunction Switch),UL_L2ENHANCED(Cell ULL2ENHANCED FunctionSwitch),EDPCCH_BOOSTING(CellE-DPCCH Boosting FunctionSwitch),DCMIMO_HSDPA(CellDC-HSDPA Combined withMIMO Function Switch),E_DRX(Enhanced
Discontinuous ReceptionFunction Switch),DC_HSUPA(Cell DC-HSUPAFunction Switch)
Actual Value Range:64QAM,MIMO, E_FACH, DTX_DRX,HS_SCCH_LESS_OPERATION, DL_L2ENHANCED,64QAM_MIMO, UL_16QAM,DC_HSDPA,UL_L2ENHANCED,EDPCCH_BOOSTING,
DCMIMO_HSDPA, E_DRX,
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 62/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 63/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-21
Parameter ID NE MML Command Feature ID Feature Name Description
uplink, or E-FACH fordownlink and E-RACH foruplink).
5)MAP_PS_STREAM_ON_HSDPA_SWITCH: When theswitch is on, a PS streamingservice is mapped on theHS-DSCH if the DL maximumrate of the service is greaterthan or equal to the HSDPAthreshold for streamingservices.
6)
MAP_PS_STREAM_ON_HSUPA_SWITCH: When theswitch is on, a PS streamingservice is mapped on theE-DCH if the UL maximumrate of the service is greaterthan or equal to the HSUPAthreshold for streamingservices.
7)MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWITCH:When the switch is on, thesignaling is transmitted at arate of 6.8 kbit/s if all thedownlink traffic is on theHSDPA channel.
8)MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWITCH:When this switch is turned on,the SRB of a CS RRCconnection cannot be
established on HSPAchannels. The RNCdetermines whether an RRCconnection request is for a CSservice based on the RRCconnection setup cause andthe value of Domain Indicator.For a UE of a version earlierthan Release 6, the RRCconnection setup cause of CSservices is OriginatingConversational Call orTerminating ConversationalCall. For a UE of Release 6 or
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 64/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 65/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-23
Parameter ID NE MML Command Feature ID Feature Name Description
DPA_SWITCH,MAP_PS_STREAM_ON_HSUPA_SWITCH,
MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWITCH,MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWITCH,MAP_CSPS_TTI_2MS_LIMIT _SWITCH
Unit:None
DefaultValue:MAP_HSUPA_TTI_2MS_SWITCH-0&MAP_INTER_ RAT_PS_IN_CHANLE_LIMIT
_SWITCH-0&MAP_PS_BE_ON_E_FACH_SWITCH-0&MAP _PS_STREAM_ON_E_FACH _SWITCH-0&MAP_PS_STRE AM_ON_HSDPA_SWITCH-0&MAP_PS_STREAM_ON_HSUPA_SWITCH-0&MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWITCH-0&MAP_SRB_ON_DCH_OR_FACH_CS _RRC_SWITCH-0&MAP_CSPS_TTI_2MS_LIMIT_SWITC
H-0
MIMO64QAMorDCHSDPASwitch
BSC6900 SET UFRC WRFD-010680
WRFD-010681
WRFD-010696
HSPA+Downlink28Mbps perUser
HSPA+Downlink21Mbps perUser
DC-HSDPA
Meaning:This switch is usedto configure the priority ofMIMO_64QAM orDC-HSDPA. According todifferent protocols, thefollowing situations mayoccur: MIMO and DC-HSDPAcannot be used together; both64QAM and DC-HSDPA aresupported, but cannot be used
together. In this case,"MIMO64QAMorDCHSDPASwitch" is used to configure thepriorities of the features.When the priority of MIMO ishigher than that ofDC-HSDPA, the priority of64QAM is higher than that ofDC-HSDPA. When the priorityof DC-HSDPA is higher thanthat of MIMO, the priority ofDC-HSDPA is higher than thatof 64QAM.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 66/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-24
Parameter ID NE MML Command Feature ID Feature Name Description
GUI ValueRange:MIMO_64QAM,DC_HSDPA
Actual ValueRange:MIMO_64QAM,DC_HSDPA
Unit:None
Default Value:DC_HSDPA
NodeBProtclVer
BSC6900 ADD UNODEB
MOD UNODEB
WRFD-010101
3GPP R9Specifications
Meaning:Protocol versionsupported by the NodeB. Thisparameter is modified basedon the actual protocol version
of the NodeB when the NodeBprotocol version upgrade,otherwise it will cause somefeatures supported by the newprotocol version unavailable.
GUI Value Range:R99, R4,R5, R6, R7, R8, R9
Actual Value Range:R99, R4,R5, R6, R7, R8, R9
Unit:None
Default Value:R9
RetryCapability
BSC6900 SET UFRC WRFD-010652
WRFD-01061403
WRFD-010636
WRFD-010685
WRFD-010683
WRFD-010684
WRFD-010686
WRFD-010687
WRFD-010
SRB overHSDPA
HSUPA 2ms TTI
SRB overHSUPA
DownlinkEnhanced L2
Downlink64QAM
2x2 MIMO
CPC - DTX /DRX
CPC -HS-SCCH lessoperation
E-DPCCHBoosting
Meaning:This parameterspecifies which HSPAtechnologies can be retried byUEs. When the HSPAtechnologies are selected andcurrently UE is not usingthem, "BSC6900" will initiatethese HSPA technologies retryfor UE.
GUI ValueRange:SRB_OVER_HSDPA,SRB_OVER_HSUPA,TTI_2MS, MIMO, 64QAM,DL_L2_ENHANCE,DTX_DRX,HSSCCH_LESS_OPERATION, MIMO_64QAM,DC_HSDPA,UL_L2_ENHANCE,UL_16QAM,EDPCCH_BOOSTING,
DCMIMO_HSDPA,
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 67/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-25
Parameter ID NE MML Command Feature ID Feature Name Description
697
WRFD-010
699WRFD-010693
WRFD-010694
WRFD-010695
WRFD-010696
DC-HSDPA+MIMO
DL64QAM+MIMO
UL 16QAM
UL Layer 2Improvement
DC-HSDPA
DC_HSUPA
Actual Value
Range:SRB_OVER_HSDPA,SRB_OVER_HSUPA,TTI_2MS, MIMO, 64QAM,DL_L2_ENHANCE,DTX_DRX,HSSCCH_LESS_OPERATION, MIMO_64QAM,DC_HSDPA,UL_L2_ENHANCE,UL_16QAM,EDPCCH_BOOSTING,DCMIMO_HSDPA,DC_HSUPA
Unit:None
DefaultValue:SRB_OVER_HSDPA-1&SRB_OVER_HSUPA-1&TTI _2MS-1&MIMO-1&64QAM-1&DL_L2_ENHANCE-1&DTX_DRX-1&HSSCCH_LESS_OPERATION-1&MIMO_64QAM-0&DC_HSDPA-0&UL_L2_ENH ANCE-0&UL_16QAM-0&EDPCCH_BOOSTING-0&DCMIMO_HSDPA-0&DC_HSUPA-0
SECCELLACTDEASW
NodeB SETMACHSPARA
WRFD-010713
Traffic-Based Activation andDeactivation oftheSupplementaryCarrier InMulti-carrier
Meaning:This parameterspecifies whether to enableTraffic-Based Activation andDeactivation of theDC-HSDPA SecondaryCarrier. If this parameter is setto ON, this function takeseffect. If this parameter is setto OFF, this function does nottake effect. When the switch isturned on, this algorithm canlower the uplink load andextend the battery life for UEs.
GUI Value Range:ON(ON),OFF(OFF)
Actual Value Range:ON, OFF
Unit:None
Default Value:OFF(OFF)
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 68/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-26
Parameter ID NE MML Command Feature ID Feature Name Description
TCell BSC6900 ADDUCELLSETUP
MODUCELLSETUP
WRFD-022000
PhysicalChannel
Management
Meaning:Difference betweenthe System Frame Number
(SFN) and NodeB FrameNumber (BFN) of the NodeBwhich the cell belongs to. It isrecommended that TCell of allintra-frequency neighboringcells under one NodeB shouldbe unique. TCell of DC carriergroup cells or MC carriergroup cells must be the same.For detailed information of thisparameter, refer to 3GPP TS25.402.
GUI Value Range:CHIP0,CHIP256, CHIP512,CHIP768, CHIP1024,CHIP1280, CHIP1536,CHIP1792, CHIP2048,CHIP2304
Actual Value Range:CHIP0,CHIP256, CHIP512,CHIP768, CHIP1024,CHIP1280, CHIP1536,CHIP1792, CHIP2048,CHIP2304
Unit:chip
Default Value:None
UARFCNDownlink
BSC6900 ADDUCELLSETUP
MODUCELLFREQUENCY
MOD
UCELLSETUP
WRFD-010101
3GPP R9Specifications
Meaning:Depending on thevalue of [Band indication], asshown below:
Band1
General frequencies:[10562-10838]
Additional frequencies: none
Band2
General frequencies:[9662-9938]
Additional frequencies:{412,437,462,487,512,537,562,587,612,637,662,687}
Band3
General frequencies:
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 69/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-27
Parameter ID NE MML Command Feature ID Feature Name Description
[1162-1513]
Additional frequencies: none
Band4
General frequencies:[1537-1738]
Additional frequencies: {1887,1912, 1937, 1962, 1987,2012, 2037, 2062, 2087}
Band5
General frequencies:[4357-4458]
Additional frequencies: {1007,1012, 1032,1037, 1062, 1087}
Band6
General frequencies:[4387-4413]
Additional frequencies: {1037,1062}
Band7
General frequencies:[2237-2563]
Additional frequencies: {2587,2612, 2637, 2662, 2687,2712, 2737, 2762, 2787,2812, 2837, 2862, 2887,2912}
Band8
General frequencies:[2937-3088]
Additional frequencies: noneBand9
General frequencies:[9237-9387]
Additional frequencies: none
BandIndNotUsed:[0-16383]
Downlink UARFCN of acell.For detailed information ofthis parameter, refer to 3GPP
TS 25.433.
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 70/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-28
Parameter ID NE MML Command Feature ID Feature Name Description
GUI Value Range:0~16383
Actual Value Range:0~16383
Unit:None
Default Value:None
UARFCNUplink
BSC6900 ADDUCELLSETUP
MODUCELLFREQUENCY
MODUCELLSETUP
WRFD-010101
3GPP R9Specifications
Meaning:Depending on thevalue of [Band indication], asshown below:
Band1:
General frequencies:[9612-9888]
Additional frequencies: none
Band2:
General frequencies:[9262-9538]
Additional frequencies:{12,37,62,87,112,137,162,187,212,237,262,287}
Band3:
General frequencies:
[937-1288]
Additional frequencies: none
Band4:
General frequencies:[1312-1513]
Additional frequencies: {1662,1687, 1712, 1737, 1762,1787, 1812, 1837, 1862}
Band5:
General frequencies:[4132-4233]
Additional frequencies: {782,787, 807, 812, 837, 862}
Band6:
General frequencies:[4162-4188]
Additional frequencies: {812,837}
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 71/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-29
Parameter ID NE MML Command Feature ID Feature Name Description
Band7:
General frequencies:
[2012-2338] Additional frequencies: {2362,2387, 2412, 2437, 2462,2487, 2512, 2537, 2562,2587, 2612, 2637, 2662,2687}
Band8:
General frequencies:[2712-2863]
Additional frequencies: none
Band9:
General frequencies:[8762-8912]
Additional frequencies: none
BandIndNotUsed:
[0-16383]
Uplink UARFCN of a cell.
Suppose the Uplink UARFCNis unspecified and the value of[Band indication] is Band1,Band2, Band3, Band4, Band5,Band6, Band7, Band8,orBand9. Then the defaultUplink UARFCN is as follows:
If the DL frequency belongs tocommon frequencies, then
Band1: Uplink UARFCN =Downlink UARFCN - 950
Band2: Uplink UARFCN =Downlink UARFCN - 400
Band3: Uplink UARFCN =Downlink UARFCN - 225
Band4: Uplink UARFCN =Downlink UARFCN - 225
Band5: Uplink UARFCN =Downlink UARFCN - 225
Band6: Uplink UARFCN =Downlink UARFCN - 225
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 72/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-30
Parameter ID NE MML Command Feature ID Feature Name Description
Band7: Uplink UARFCN =Downlink UARFCN - 225
Band8: Uplink UARFCN =Downlink UARFCN - 225
Band9: Uplink UARFCN =Downlink UARFCN - 475
If the DL frequency belongs tospecial frequencies, then
Band2: Uplink UARFCN =Downlink UARFCN - 400
Band4: Uplink UARFCN =Downlink UARFCN - 225
Band5: Uplink UARFCN =Downlink UARFCN - 225
Band6: Uplink UARFCN =Downlink UARFCN - 225
Band7: Uplink UARFCN =Downlink UARFCN - 225
For detailed information of thisparameter, refer to 3GPP TS25.433.
GUI Value Range:0~16383
Actual Value Range:0~16383
Unit:None
Default Value:None
ULLdbDRDLoadRemainThdDcHSDPA
BSC6900 ADD UCELLDRD
MOD UCELLDRD
WRFD-02040002
Inter SystemDirect Retry
Meaning:Load threshold forDC-HSDPA UEs to triggerload balance DRD in theuplink. If the remainingnumber of equivalent users in
the uplink is less than thevalue of this parameter, uplinkload balance DRD forDC-HSDPA traffic is triggeredwhen DC-HSDPA UEs accessthe cell.
GUI Value Range:0~100
Actual Value Range:0~100
Unit:%
Default Value:25
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 73/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-31
Parameter ID NE MML Command Feature ID Feature Name Description
ULLdbDRDOff setDcHSDPA
BSC6900 SET UDRD WRFD-02040002
Inter SystemDirect Retry
Meaning:Available uplinkequivalent user number offset
used to select a direct retrycandidate cell when uplinkload balancing DRD algorithmis activated for HSDPA traffic.If the difference of theavailable remaining number ofuplink equivalent usersbetween the target cell andthe serving cell is greater thanthe value of this parameter,the target cell satisfiesconditions for a direct retrycandidate cell.
GUI Value Range:0~100
Actual Value Range:0~100
Unit:%
Default Value:10
ULLdbDRDSwitchDcHSDPA
BSC6900 SET UDRD WRFD-02040002
Inter SystemDirect Retry
Meaning:Whether to activatethe uplink load balancing DRDalgorithm for DC-HSDPAtraffic. If this switch is turned
on, the BSC6900 selects theprimary cell based on thenumber of uplink equivalentusers in the two cellsproviding DC-HSDPAservices. When this switch isturned on andDR_RAB_SING_DRD_SWITCH in "SETUCORRMALGOSWITCH" ison, this algorithm applies to asingle service.
When this switch is turned onandDR_RAB_COMB_DRD_SWITCH in "SETUCORRMALGOSWITCH" ison, this algorithm applies tocombined services.
GUI Value Range:ON, OFF
Actual Value Range:ON, OFF
Unit:None
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 74/78
WCDMA RAN
DC-HSDPA 8 Parameters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
8-32
Parameter ID NE MML Command Feature ID Feature Name Description
Default Value:OFF
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 75/78
WCDMA RAN
DC-HSDPA 9 Counters
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
9-1
9 Counters
Table 9-1 Counter description
Counter ID Counter Name Counter Description NE Feature ID Feature Name
50331719 VS.HSDPA.DCCfg.AnchorCarrierActedNum
Number of times that allthe users configured inDC mode in a cell arescheduled by AnchorCarrier duringthe measurementperiod
NodeB WRFD-010610
WRFD-010689
WRFD-010696
HSDPAIntroductionPackage
HSPA+ Downlink42Mbps per User
DC-HSDPA
50331720 VS.HSDPA.DCCfg.SupCarrierActedNum
Total number of timesDC-HSDPA-enabledusers are scheduled bythe supplementarycarrier
NodeB WRFD-010610
WRFD-010689
WRFD-010696
HSDPAIntroductionPackage
HSPA+ Downlink42Mbps per User
DC-HSDPA
50331721 VS.HSDPA.DCCfg.DualCarrierActedNum
Total number of timesDC-HSDPA-enabledusers are scheduled bythe anchor andsupplementary carriersat the same time
NodeB WRFD-010610
WRFD-010689
WRFD-010696
HSDPAIntroductionPackage
HSPA+ Downlink42Mbps per User
DC-HSDPA
50341702 VS.HSDPA.DCCfg.SupCarrierDeact.TimeRatio
The Ratio Of Dc Deact NodeB WRFD-010713
Traffic-Based Activation andDeactivation ofthe DC-HSDPASecondaryCarrier
73403828 VS.HSDPA.RAB.DC.AttEstab
Number of DC-HSDPARAB Setup Requests inthe primary carrier ofDC-HSDPA counted for
cell
BSC6900 WRFD-010696
DC-HSDPA
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 76/78
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 77/78
WCDMA RAN
DC-HSDPA 10 Glossary
Issue 04 (2013-06-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
10-1
10 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary .
8/16/2019 Dual Carrier-hsdpa(Ran14.0 04)
http://slidepdf.com/reader/full/dual-carrier-hsdparan140-04 78/78
WCDMA RAN
DC-HSDPA 11 Reference Documents
11 Reference Documents
[1] 3GPP TS 25.331, "Radio Resource Control (RRC)"
[2] 3GPP TS 25.306, "UE Radio Access capabilities"
[3] HSDPA Feature Parameter Description
[4] Radio Bearers Feature Parameter Description
[5] Load Control Feature Parameter Description
[6] Directed Retry Decision Feature Parameter Description
[7] Handover Feature Parameter Description
[8] Green BTS Feature Parameter Description