Date post: | 10-Feb-2016 |
Category: |
Documents |
Upload: | andreibertea7771 |
View: | 32 times |
Download: | 0 times |
PIONEER CORPORATION 4-1, Meguro 1-chome,PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, LonPIONEER EUROPE NV Haven 1087, Keetberglaan 1, 912PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253
PIONEER CORPORATION 2007
DV-600AV-S
Meguro-ku, Tokyo 153-8654, Japang Beach, CA 90801-1760, U.S.A.
0 Melsele, BelgiumAlexandra Road, #04-01, Singapore 159936
ORDER NO.
RRV3611
DVD PLAYER
DV-600AV-SDV-600AV-KTHIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Region No. Remarks
DV-600AV-S WYXZT5 AC 220 V to 240 V 2
DV-600AV-S WVXZT5 AC 220 V to 240 V 2
DV-600AV-S YXZTUR5 AC 220 V to 240 V 5
DV-600AV-K WYXZT5 AC 220 V to 240 V 2
DV-600AV-K YXZTUR5 AC 220 V to 240 V 5
For details, refer to "Important Check Points for Good Servicing" .
T-ZZV MAY 2007 printed in Japan
C
D
F
A
B
E
1 2 3 4SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trainedto properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING !
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1.A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS
FOR DVD : MAXIMUM OUTPUT POWER : 5 mWWAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mWWAVELENGTH : 780 nm
Additional Laser Caution
∗ : See page 29.
1.• Laser diode is driving with Q2303,Q2305(650nm LD) and Q2302, Q2304(780nm LD)on the DVD MT PCB Assy.Therefore, when short-circuit between the emitter and collector of these transistors or the base voltage is supplied for transistors turn on, the laser oscillates. (failure mode)• In the test mode ∗ , there is the mode that the laser oscillates except for the disc judgment and playback. LD ON mode in the test mode oscillates with the laser forcibly.
2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam.
LABEL CHECK
(Printed on the Rear Panel)
Location: inside of the unit
TOP MENU
MENU
RETURN
ENTER
HOMEMENU
OPEN/CLOSE
STANDBY/ON
DV-600AV-S21 2 3 4
C
D
F
A
B
E
3
5 6 7 8
[Important Check Points for Good Servicing]In this manual, procedures that must be performed during repairs are marked with the below symbol.Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S4
1 2 3 4
CONTENTS SAFETY INFORMATION..................................................................................................................................... 21. SERVICE PRECAUTIONS ............................................................................................................................... 5
1.1 NOTES ON SOLDERING .......................................................................................................................... 51.2 WHEN REPLACING DVD DECK ............................................................................................................... 51.3 DISC REMOVAL METHOD........................................................................................................................ 6
2. SPECIFICATIONS ............................................................................................................................................ 72.1 ACCESSORIES ......................................................................................................................................... 72.2 SPECIFICATIONS...................................................................................................................................... 82.3 DISC/CONTENT FORMAT ........................................................................................................................ 92.4 PANEL FACILITIES.................................................................................................................................. 11
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 143.1 CHECK POINTS AFTER SERVICING..................................................................................................... 143.2 PCB LOCATIONS .................................................................................................................................... 153.3 JIGS LIST ................................................................................................................................................ 16
4. BLOCK DIAGRAM.......................................................................................................................................... 184.1 OVERALL WIRING CONNECTION DIAGRAM........................................................................................ 184.2 OVERALL BLOCK DIAGRAM.................................................................................................................. 204.3 DVD LOADER BLOCK DIAGRAM ........................................................................................................... 214.4 POWER BLOCK DIAGRAM..................................................................................................................... 22
5. DIAGNOSIS.................................................................................................................................................... 235.1 TROUBLE SHOOTING ............................................................................................................................ 235.2 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY......................... 28
6. SERVICE MODE ............................................................................................................................................ 296.1 SERVICE MODE PROCEDURE.............................................................................................................. 296.2 SERVICE MODE IN ................................................................................................................................. 306.3 DISPLAY SPECIFICATION OF THE SERVICE MODE............................................................................ 316.4 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY................................................................... 326.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE.................................................................... 33
7. DISASSEMBLY............................................................................................................................................... 347.1 EXTERIOR SECTION.............................................................................................................................. 347.2 DVD DECK SECTION.............................................................................................................................. 36
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 408.1 ADJUSTMENT......................................................................................................................................... 408.2 RE-WRITE FOR DVD FIRMWARE.......................................................................................................... 40
9. EXPLODED VIEWS AND PARTS LIST .......................................................................................................... 429.1 PACKING SECTION ................................................................................................................................ 429.2 EXTERIOR SECTION.............................................................................................................................. 449.3 06 DVD MECHA SECTION...................................................................................................................... 46
10. SCHEMATIC DIAGRAM ............................................................................................................................... 4810.1 DVD MT PCB ASSY (1/7) ...................................................................................................................... 4810.2 DVD MT PCB ASSY(2/7) ....................................................................................................................... 5010.3 DVD MT PCB ASSY(3/7) ....................................................................................................................... 5210.4 DVD MT PCB ASSY(4/7) ....................................................................................................................... 5410.5 DVD MT PCB ASSY(5/7) ....................................................................................................................... 5610.6 DVD MT PCB ASSY(6/7) ....................................................................................................................... 5810.7 DVD MT PCB ASSY(7/7) ....................................................................................................................... 6010.8 OPERATION 1 and OPERATION 2 PCB ASSYS .................................................................................. 6210.9 POWER PCB ASSY (1/2) ...................................................................................................................... 6410.10 POWER PCB ASSY (2/2) .................................................................................................................... 6610.11 USB PCB ASSY................................................................................................................................... 6810.12 WAVE FORMS ..................................................................................................................................... 70
11. PCB CONNECTION DIAGRAM ................................................................................................................... 7211.1 DVD MT PCB ASSY............................................................................................................................... 7311.2 OPERATION 1 PCB and OPERATION 2 PCB ASSYS.......................................................................... 7511.3 POWER PCB ASSY............................................................................................................................... 7611.4 USB PCB, LOADING MOTOR and SW ASSYS .................................................................................... 78
12. PCB PARTS LIST ......................................................................................................................................... 79
1 2 3 4
C
D
F
A
B
E
5
5 6 7 8
1. SERVICE PRECAUTIONS1.1 NOTES ON SOLDERING
1.2 WHEN REPLACING DVD DECK
NOTES ON SOLDERING• For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairsaccompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, althoughthe temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron.
Do NOT use a soldering iron whose tip temperature cannot be controlled.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:• Parts numbers of lead-free solder:
GYP1006 1.0 in dia.GYP1007 0.6 in dia.GYP1008 0.3 in dia.
Before removing Pick Up PCB and DVD PCB connector, short circuit the position shown in Fig. 1 usinga soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged.
WHEN REPLACING DVD DECK
[ Removing the DVD Deck ]
[ Installing the DVD Deck ]
Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVDPCB connector.
NOTE
Fig. 1
Before your operation, please read “PREPARATION OF SERVICING” .Use the Lead Free solder.Manual soldering conditions• Soldering temperature: 320 ± 20˚C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5CuWhen Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent theFlux smoke from it.
•••
•
Short circuit using asoldering iron.
Pick Up PCB
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S6
1 2 3 4
1.3 DISC REMOVAL METHOD
The laser diode used for a pickup head may be destroyed with external static electricity.Moreover, even if it is operating normally after repair, when static electricity discharge isreceived at the time of repair, the life of the product may be shortened.Please perform the following measure against static electricity, be careful of destruction of alaser diode at the time of repair.
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat.• Soldering iron with ground wire or ceramic type is used.• A worker needs to use a ground conductive wrist strap for body.
PREPARATION OF SERVICING
If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the stepsbelow.
Set the DVD to the Stand-by Mode.Press and hold the 'STOP' key on the front panel.Simultaneously press and hold the POWER key on the front panel.The 4 digit password has now been cleared.
1.2.3.4.
PARENTAL CONTROL - RATING LEVEL4 DIGIT PASSWORD CANCELLATION
NOTE: The above procedure will reset ALL of the player's settings to the default factory state.
Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock.(Refer to Fig. 1)Manually open the Tray.
Please strongly pushing Rack Loading (White) to release the lock because the tray doesn't go outeasily.
1.
2.
Fig. 1
Rack Loading (White)
DVD Player (Bottom Side)
NOTE:
DISC REMOVAL METHOD AT NO POWER SUPPLY
1 2 3 4
C
D
F
A
B
E
7
5 6 7 8
2. SPECIFICATIONS2.1 ACCESSORIES
Accessories
• Remote control ×1(07650NU020)
• Power cable ×1(1206158802 : WYXZT5, WYXZTUR5)
• Audio / Video cable(1.2m) ×1(red/white/yellow)
(06CPBA2006)
• Dry cell batteries ×2(AA/R6P)
• Warranty Card
• Operating Instructions
(1206138802 : WVXZT5)
0
1 2 3
4 5 6
7 8 9
PLAY MODE SURROUND ZOOM DISPLAY
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S8
1 2 3 4
2.2 SPECIFICATIONS
GeneralPower requirements . . . . . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 HzPower consumption
DV-600AV . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 WPower consumption (standby. . . . . . . . . . . . . . . . 0.8 WWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 kg Dimensions
DV-600AV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 (W) mm x 49.5 (H) mm x 215.5 (D) mm
Operating temperature. . . . . . . . . . . . . +5 ºC to +35 ºCOperating humidity. . . . . . . . . . . . . . . . . . . 5 % to 85 %
(no condensation)
AV Connector (21-pin connector assignment)AV connector output. . . . . . . . . . . . . . 21-pin connectorThis connector provides the video and audio signals for connection to a compatible colour TV or monitor.
PIN no.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 2/R out3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 1/L out4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B out8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G out15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R out17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video out21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND
Component video outputY (luminance) - Output level . . . . . . . . . . 1 Vp-p (75 Ω)PB (color) - Output level . . . . . . . . . . . .0.7 Vp-p (75 Ω)PR (color) - Output level . . . . . . . . . . . .0.7 Vp-p (75 Ω)Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
S-video outputY (luminance) - Output level. . . . . . . . . . .1 Vp-p (75 Ω)C (color) - Output level . . . . . . . . . . . 286 mVp-p (75 Ω)Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-video
Video outputOutput level . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p (75 Ω)Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
Audio output (1 stereo pair)Output level . . . . . . . . . . . . . . . . . . During audio output
200 mVrms (1 kHz, –20 dB)Number of channels. . . . . . . . . . . . . . . . . . . . . . . . . . .2Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA
HDMI outputHDMI output . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 pin
Audio output (multi-channel / L, R, C, SW, SL, SR)Output level. . . . . . . . . . . . . . . . . . .During audio output
200 mVrms (1 kHz, –20 dB)Number of channels. . . . . . . . . . . . . . . . . . . . . . . . . . .6Jacks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RCA jack
Digital audio characteristicsFrequency response. . . . . . . . . . . . . . . .4 Hz to 44 kHzS/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 dBDynamic range . . . . . . . . . . . . . . . . . . . . . . . . . .100 dBTotal harmonic distortion . . . . . . . . . . . . . . . . 0.0023 %Wow and flutter . . . . . . . . . . . . . .Limit of measurement
(±0.001 % W. PEAK) or lower
Digital outputCoaxial digital output . . . . . . . . . . . . . . . . . . .RCA jackOptical digital output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optical digital jack
AccessoriesRemote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . . . . . . 2Audio/video cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Operating instructions
The specifications and design of this product are subject to change without notice, due to improvement.
Published by Pioneer Corporation.Copyright © 2007 Pioneer Corporation.
All rights reserved.
1 2 3 4
C
D
F
A
B
E
9
5 6 7 8
2.3 DISC/CONTENT FORMAT
Disc/content format playback compatibilityThis player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable formatósee below for further compatibility information.
Please also note that recordable discs cannot be recorded using this player.
• This unit will play DVD+R/+RW discs.
• is a trademark of DVD Format/Logo Licensing Corporation.
• is a trademark of Fuji Photo Film Co. Ltd.
• Also compatible with KODAK Picture CD
This player supports the IECís Super VCD standard. Compared to the Video CD standard, Super VCD offers superior picture quality, and allows two stereo soundtracks to be recorded. Super VCD also supports the widescreen size.
DVD-Video DVD-R DVD-RW
Video CDAudio CD CD-R CD-RW
DVD-Audio
Super Audio CD
Fujicolor CD
Super VCD
About DualDisc playbackA DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material.
The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play.
The DVD side of a DualDisc plays in this product. DVD-Audio content will not play.
For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.
CD-R/-RW compatibility• Compatible formats: CD-Audio, Video CD/
Super VCD, ISO 9660 CD-ROM* containing MP3, WMA, MPEG-4 AAC, JPEG or DivX video/WMV files* ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible with this player.
• Multi-session playback: No
• Unfinalized disc playback: No
• File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder
DVD+R/DVD+RW compatibilityOnly DVD+R/DVD+RW discs recorded in 'Video Mode (DVD Video Mode)' which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately.
DVD-R/-RW compatibility• Compatible formats: DVD-Video, Video
Recording (VR)** Edit points may not play exactly as edited; screen may go momentarily blank at edited points.
• Unfinalized playback: No
• MP3/WMA/MPEG-4 AAC/JPEG or DivX video/WMV file playback on DVD-R/-RW: No
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S10
1 2 3 4
WMA (Windows Media™ Audio) compatibilityThis player can playback Windows Media Audio content.WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media Player for Windows XP, Windows Media Player 9 or Windows Media Player 10 series.Windows Media is a trademark of Microsoft Corporation.This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.
Compressed audio compatibility• Compatible formats: MPEG-1 Audio Layer
3 (MP3), Windows Media Audio (WMA), MPEG-4 AAC
• Sampling rates: 32 kHz, 44.1 kHz or 48 kHz• Bit-rates: Any (128 kbps or higher recommended) • VBR (variable bit rate) MP3/WMA/MPEG-4
AAC playback: No• WMA lossless encoding compatible: No • DRM (Digital Rights Management)
compatible: No (DRM-protected audio files will not play in this player
• File extensions: .mp3, .wma, .m4a (these must be used for the player to recognize MP3, WMA and MPEG-4 AAC files - do not use for other file types)
JPEG file compatibility• Compatible formats: Baseline JPEG and
EXIF 2.2* still image files up to a resolution of 3072 x 2048.* File format used by digital still cameras.
• Progressive JPEG compatible: No• File extensions: .jpg (must be used for the
player to recognize JPEG files – do not use for other file types)
PC-created disc compatibilityDiscs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information.Discs recorded in packet write mode (UDF format) are not compatible with this player.Check the DVD-R/-RW or CD-R/-RW software disc boxes for additional compatibility information.
DivX video compatibility• Official DivX c Ultra Certified product.• Plays all versions of DivX c video (including
DivX c 6) with enhanced playback of DivXc
media files and the DivX c Media Format.• File extensions: .avi and .divx (these must
be used for the player to recognize DivX video files). Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player.
About WMVWMV is an acronym for Windows Media Video and refers to a video compression technology developed by Microsoft Corporation. WMV content can be encoded by using Windows Media® Encoder.This player is compatible with WMV9 files that are encoded by using the Windows Media® Encoder 9 Series, with .wmv as an extension.Compatible with size under 720 x 576 pixels/720 x 480 pixels.Advanced Profile is not supported.
About DivX videoDivX is a media technology created by DivX, Inc. DivX media files contain not only video but also include advanced media features like menus, subtitles, and alternate audiotracks. This player can play DivX videos burned on CD-R/-RW/-ROM discs. Keeping the same terminology as DVD-Video, individual DivX video files are called ˝Titles˝. When naming files/titles on a CD-R/-RW disc prior to burning, keep in mind that by default they will be played in alphabetical order.
About MPEG-4 AACAdvanced Audio Coding (AAC) is at the core of the MPEG-4 AAC standard, which incorporates MPEG-2 AAC, forming the basis of the MPEG-4 audio compression technology. The file format and extension used depend on the application used to encode the AAC file. This unit plays back AAC files encoded by iTunes© bearing the extension '.m4a'. DRM-protected files will not play, and files encoded with some versions of iTunes© may not play, or filenames may display incorrectly.Apple and iTunes are trademarks of Apple Inc., regis-tered in the U.S. and other countries.
1 2 3 4
C
D
F
A
B
E
11
5 6 7 8
2.4 PANEL FACILITIES2.4.1 FRONT PANEL SECTION
Front panel
2 3 4 51
7 6810 917 141516 111213
1 STANDBY/ONPress to switch the player on or into standby.
2 Disc tray
3
9 OPEN/CLOSEPress to open or close the disc tray.
4
11
Press to pause playback. Press again to restart.
5
10
Press to start or resume playback.
12
Press to stop the disc (you can resume play-back by pressing (play)).
8 DisplayDescription of the display.
13 and • Press and hold for fast reverse/forward
scanning.
• Press to jump to the previous/next chapter or track.
TOP MENU
ENTER & cursor buttons
MENU
6 RETURN
7 HOME MENU
Displays the ‘top menu’ of a DVD disc—this varies with the disc.
Displays a DVD disc menu—this varies with the disc and may be the same as the ‘top menu’.
Selects the current menu option.
Returns to the previously dis-played menu screen.
Compatible17
This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode.
14 HDMI indicatorLights when this player is recognized by
Press to turn to USB MODE.Press once again to return to DVD mode.
Connect USB device
another HDMl or DVI/HDCP compatible component.
15 DVD/USB
16 USB port (Type A)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S12
1 2 3 4
2.4.2 REMOTE CONTROL
Remote control
0
1 2 3
4 5 6
7 8 9
PLAY MODE SURROUND ZOOM
1 14
15
16
17
18
19
20
21
23
2
4
5
6
7
8
10
1213
3
9
11 22
24
DISPLAY
1Press to switch the player on or into standby.
2 AUDIOPress to select the audio channel or language.
3 SUBTITLEPress to select a subtitle display.
4 Number buttons
5 TOP MENUPress to display the top menu of a DVD disc.
6 ENTER & cursor buttons
Use to navigate on-screen displays and menus. Press ENTER to select an option or execute a command.
7 HOME MENUPress to display (or exit) the on-screen display.
8Use for reverse slow motion playback, frame reverse and reverse scanning.
9Press to start or resume playback.
10
Press to jump to the beginning of the current
chapter or track, then to previous chapters/tracks.
11Press to pause playback; press again to restart.
12 PLAY MODEPress to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode).
13 SURROUNDPress to activate/switch off 2V/SRS TruSurround.
14Press to open or close the disc tray.
15 ANGLEPress to change the camera angle during DVD multi-angle scene playback.
16 DVD/USBPress to turn to USB MODE or return to DVD mode.
17 CLEARPress to clear a numeric entry.
18 MENUPress to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded.
1 2 3 4
C
D
F
A
B
E
13
5 6 7 8
19 RETURNPress to return to a previous menu screen.
20Use for forward slow motion playback, frame advance and forward scanning.
21Press to jump to the next chapter or track.
22Press to stop the disc (you can resume playback by pressing (play)).
23 DISPLAYPress to display information about the disc playing.
24 ZOOMPress to change the zoom level.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S14
1 2 3 4
3. BASIC ITEMS FOR SERVICE3.1 CHECK POINTS AFTER SERVICING
Check points after servicing (DVD player)
To keep the product quality after servicing, confirm recommended check points shown below.
See the table below for the items to be checked regarding video and audio:
No. Procedure Check points
1 Confirm the firmware version on Service Mode. The version of the firmware must be latest.Update firmware to the latest one, if it is not the latest.
The customer complain must not be reappeared.Video, audio and operations must be normal.2
Confirm whether the customer complain has been solved. If the customer complain occurs with the specific disc, use it for the operation check.
The error rates must be less than 5.0e-4.3
Confirm playback error rates at the innermost and outermost tracks by using the following disc.DVD test disc (GGV1025)
4 Play back a DVD.(Menu operation, Title/chapter search)
Audio and operations must be normal.
5Play back a DVD.(Menu operation, Title/chapter search)
Video, audio and operations must be normal.
6 Check the appearance of the product. No scratches or dirt on its appearance after receiving it for service.
Items to be checked regarding video Item to be checked regarding audio
Block noise Distortion
Horizontal noise Noise
Dot noise Volume too low
Disturbed image (video jumpiness) Volume too high
Too dark Volume fluctuating
Too bright Sound interrupted
Mottled color
1 2 3 4
C
D
F
A
B
E
15
5 6 7 8
3.2 PCB LOCATIONS
OPERATION 1 PCB ASSY
OPERATION 2 PCB ASSY
OPERATION 3 PCB ASSY
POWER PCB ASSYUSB PCB ASSY
DVD MT PCB ASSY
DVD MECHA ASSY
Mark No. Description Part No.LIST OF ASSEMBLIES 1..DVD MT PCB ASSY A2K501A130 1..OPERATION 1 PCB ASSY A2K501A270 (WYXZT5, WVXZT5 types) (*) 1..OPERATION 1 PCB ASSY A2K504A270 (YXZTUR5 types) (*) 1..OPERATION 2 PCB ASSY A2K401A280 1..OPERATION 3 PCB ASSY A2K401ADF0 > 1..POWER PCB ASSSY A2K503A240 1..USB PCB ASSY A2K401ADD0 1..DVD MECHA ASSY A2K001A650
(*) A2K501A270 and A2K504A270 have same service parts. But they are NOT COMPATIBLE.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S16
1 2 3 4
3.3 JIGS LIST
Service Remote Control Unit GGF1381 diagnosisName Jig No. Remarks
DVD Test Disc (DVD-Video,NTSC) GGV1025 Operation CheckDVD Test Disc (DVD-Video,PAL)CD Test Disc
GGV1101STD-905
Operation CheckOperation Check
7 Jigs list
Lubricants and Glues list
Cleaning
Daifree GEM1036 (ZLX-ME413A) Refer to "9.3 06 DVD MECHA SECTION"
Grease GYA1001 (ZLB-PN397B) Refer to "9.3 06 DVD MECHA SECTION"
Grease GEM1018 Refer to "9.3 06 DVD MECHA SECTION"
Name Lubricants and Glues No. RemarkName Lubricants and Glues No. Remark
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:
Pickup leneses Cleaning liquid : GEM1004
Cleaning paper : GED-008
Position to be cleaned Cleaning tools RemarkPosition to be cleaned Cleaning tools Remark
1 2 3 4
C
D
F
A
B
E
17
5 6 7 8
DV-600AV-S5 6 7 8
C
D
F
A
B
E
64 53
4
5
D2-
D1+
D1-
S
D1-
PCA13
DV-600AV-S18
1 2 3 4
4. BLOCK DIAGRAM4.1 OVERALL WIRING CONNECTION DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
112
11
10
9
8
7
6
5
4
3
2
1
2
1
CP8102
2
1
CP8001
4321
43214321
21CP5
901
11
10
9
8
7
6
5
4
3
2
111
10
9
8
7
6
5
4
3
2
1
14
13
12
11
10
9
8
7
6
4
5
3
2
1
CP4003
14
13
12
11
10
9
8
7
6
4
5
3
2
1
CP502
5
4
3
2
1
CP605
5
4
3
2
1
CP604
654321
654321
NOTE : THE TIMETHIS INTERCONNECTION DIAGRAM IS THE LATEST ATOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
Vout
B+
GND
OS651
1
2
3
J810121PIN CONNECTOR
1
10
11
12
13
14
15
16
17
18
19
220
213
4
5
6
7
8
9
J501AC INLET
12
CD501_2AC220V-240V_50Hz/60Hz(EU)
J7304S-VIDEO OUT for HE
12
34
56
H1H2
E
H1H2
E
J7302CVBS/Y/U/V
1
23 6
CP7301
FLDC-
FLDC+
V+3E
-28V
DGND
DGND
DO (F to M)
DI (M to F)
IR
STB
CLK
(CD601)
11
10
9
8
7
6
5
4
3
2
1
11
10
9
8
7
6
5
4
3
2
1
CP4002
2
1
2
1GND
SPDIF
GNDSPDIF
RGB-H
R
B
G
GND
CVBS
AUDIO R
GND
AUDIO L
FS
GND
GND
6 6
14
13
14
13
12
11
10
9
8
7
12
11
10
9
8
7
(CD502)
2
1
2
1
5
4
3
5
4
3
AT+3.3V
FL DC-
FL DC+
-28V
AT+3.3V
P.CON+6V
GND(M)
GND(D)
P.ON-H
GND
P.CON+5V
GND
P.CON+12V
AT+12V for MUTE
2
2
3
3
4
4
5
5
6
677
8
8
9
9
10
10
11
11
12
1 1 2
1
RGB-H
R
B
G
GND
CVBS
AUDIO R
GND
AUDIO L
FS
GND
GND
CP503
AT+3.3V
AT+3.3V
FL DC-
FL DC+
P.ON-H
P.CON+6V
-28V
GND(M)
GND(D)
(CD
6601
)
654321
CP4
004
USB
N
GN
D
GN
D
USB
_PO
WER
USB
_FLA
G
USB
P
DPF015
POWER PCBPCB240
GND
P.CON+12V
P.CON+5V
GND
AT+12V for MUTE
(CD
6602
)
4321
4321
654321
D2+
D2-
S
NC
NC
NC
NC
NC
GN
D
CP5
04
USB
+5V
GN
D
USB
+5V
PCBDD0DEF133
USB PCB
GN
D
USB
N
USB
_PO
WER
USB
_FLA
G
GN
D
USB
P
CP6
601
(CD
6603
)
+5V
GN
D
USB
_DN
USB
_DP
GN
D
GN
D
P.C
ON
+5V
P.C
ON
+5VC
P660
2
1
2
3
4
5
5
4
3
2
1
(CD604)
OPERATION PCB
DEF126PCB270
DEF130PCBDF0
OPERATION3 PCB
SW2
POWER
V+3E
LED
USB
SW2
POWER
V+3E
LED
USB
CP601
DGND
DGND
FLDC+
-28V
FLDC-
DI (M to F)
V+3E
STB
DO (F to M)
IR
CLK
NN
L
OPERATION 2 PCB ASSY(A2K401A280)OPERATION 3 PCB ASSY(A2K401ADF0)
POWER PCB ASSY(1/2, 2/2)(A2K503A240)
USB PCB ASSY(A2K401ADD0)
DVD MT(A2K501
OPERATION 1 PCB ASSY (WYXZT5, WVXZT5 types : A2K501A270)(YXZTUR5 types : A2K504A270)
1 2 3 4
C
D
F
A
B
E
CP5
901
HH2
E
J7CVB
1
23
PCBDD0DEF133
USB PCB
DVD(A2K
19
5 6 7 8
1918171615141312111098764 5321
1
2
3
4
5
CP2302
1
2
3
4
5
6
CP2303
24
23
22
21
20
19
2
1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
CP2301
OS8101OPTICAL
123
ATTENTION : LES PIECES REPAREES PAR UN > ETANTDANGEREUSES AN POINT DE VUE SECURITEN’UTILISER QUE CELLS DECRITESDANS LA NOMENCLATURE DES PIECES.
CAUTION : SINCE THESE PARTS MARKED BY > ARECRITICAL FOR SAFETY,USE ONESDESCRIBED IN PARTS LIST ONLY
H1H2
E
H1H2
E
J8002LS/RS/C/LFE
1
23
4
56H1H2
E
1
302S/Y/U/V
4
56H1H2
E
J8001L/R
1
23
GN
D
VCC
INPU
T
VRCOM
TRKG DRV
TRKG RTN
FOCS RTN
FOCS DRV
VCC
D
B
VR780(CD)
VRF(RF_OUT)
SW1(DVD/CD)
C
E
VS
F
GND
A
VR650(DVD)
GND
GND
LD_DVD(650)
LD_CD(780)
PD/GND
NC
D2+
D2-
S
D2-
D1+
D1-
S
D0+
D0-
S
D0-
CLK
-S
CLK
-
CEC
SCL
SDA
GN
D
POW
ER
HO
TPLU
G
NC
D1-
CLK
+
DMF090
DVD MT PCBPCB130
SPD+
SPD-
SLD+
SLD-
LIMIT SW
SW(GND)
GND
CLOSE
LOAD+
OPEN
LOAD-
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
6
5
4
3
2
1
B
A
VRCOM
VR780(CD)
VRF(RF_OUT)
SW1(DVD/CD)
C
VR650(DVD)
GND
LD_DVD(650)
LD_CD(780)
PD/GND
TRKG DRV
TRKG RTN
FOCS RTN
FOCS DRV
VCC
D
E
VS
F
GND
GND
NC
DM-4PBDRIVEDVD
OPTICAL PICK-UP
JCV9B07DED012
(SW PCB)
PCB640
M
6
5
4
3
2
1 GND(SW)
FEED MOTOR (+)
SPINDLE MOTOR (+)
SPINDLE MOTOR (-)
FEED MOTOR (-)
PICK UP INNER LIMIT SWITCH
SW2
M2601
BCZ3B03M2602
ESE22MH24CD23012H062102
M
(LOADING MOTOR PCB)SSS-13-2
SW1
GND(SW)
SW-2(CLOSE)
SW-1(OPEN)
LOADING MOTOR(-)
LOADING MOTOR(+)
DED003PCB610 BCZ3B52
M2603
CD23022H052601
M
5
4
3
2
1
MT PCB ASSY (1/7–7/7)501A130)
DVD MECHA ASSY(A2K001A650)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S20
1 2 3 4
4.2 OVERALL BLOCK DIAGRAM
P.C
ON
+12
V
AC
220V
~24
0VV
+5H
27M
Hz
-28V
AT+
12V
for
mut
e
AT+
3.3V
P.C
ON
+6V
P.C
ON
+5V
PO
WE
RS
UP
PLY
DV
D L
OA
DE
R(D
M4)
MO
TOR
DR
IVE
RIC
2301
AM
5766
FIP
DR
IVE
R IC
IC
651
PT
6315
8K E
EP
RO
MIC
4001
S-2
4CS
08A
FJ-
TB
- 1G
E
FIP
HN
V-0
8SS
44T
KE
Y
SE
RV
O
RF
SE
RV
O
IR
FP,
ST
B
AS
PD
IF
RESET
LD_D
VD
,LD
_CD
IR10
8MH
zT
V E
ncod
er
MP
EG
-1/2
/JP
EG
VID
EO
DE
CO
RD
ER
RF
OV
ER
AL
L B
LO
CK
DIA
GR
AM
IR R
EC
EIV
ER
(O
S65
1)R
OM
-N34
0TA
O
16M
bit F
LAS
HIC
4004
ES
29LV
160E
B-7
0 T
G
64M
bit S
DR
AM
IC40
05H
Y57
V64
1620
ET
P-6
-C
SD
A, S
CL
AM
UT
EM
PE
G/M
ICO
N B
LOC
KIC
4002
MT
1389
EX
E/S
-LA
UD
IO C
OD
EC
/IN
TE
RN
AL
DA
C
+1.
8V
A0~
A20
, A
D0~
AD
7M
A0~
MA
11,
DQ
0~D
Q15
RE
SE
T IC
IC40
03R
3112
N29
1A-
TR
-FA
VID
EO
DR
IVE
R 6
CH
ICIC
7301
LA73
054-
TLM
-E
4CH
VID
EO
DA
C
HD
MI
CO
NN
EC
TOR
CP
5901
TX
0+/-
,T
X1+
/-,
TX
2+/-
, T
XC
+/-
S_V
IDE
OS
CV
BS
OU
T
RG
B O
UT
CO
CO
AX
IAL
OP
TIC
AL
OP
IC80
03/4
/5A
UD
IO D
AC
ICP
CM
1742
KE
/2K
DA
C_X
CS
O, S
CK
, SD
,A
CLK
, AB
CK
, ALR
CK
, A
SD
AT0~
2
IC80
02/7
/8A
UD
IO L
PF
AN
D A
MP
ICR
C45
80ID
R
C
LFE
SR LR
FLD
C+
/-
SL
21 P
IN CV
BS
VUY4C
H B
US
SW
ICIC
7302
SN
74C
BT
3257
PW
R
1 2 3 4
C
D
F
A
B
E
21
5 6 7 8
4.3 DVD LOADER BLOCK DIAGRAM
DV
D L
OA
DE
R/M
PE
G B
LO
CK
DIA
GR
AM
DV
DLo
ader
(DM
-4)
MP
EG
/MIC
ON
ICIC
4002
MT
1389
EX
E/S
-L
X40
0127
MH
z
IOA
, V20
C
RF,
A, B
, C, D
, E, F
, MD
I1
LD_D
VD
, LD
_CD
Q23
02~
2305
LD D
RIV
E
LDO
1, L
DO
2
MO
TO
R D
RIV
ER
ICIC
2301
AM
5766
DM
SO
, FM
SO
, T
RO
PE
N, T
RC
LOS
E,
TR
SO
, FO
SO
, S
TB
Y, V
1P4
T+
/-, F
+/-
,LO
AD
+/-
, M
OT
_SLE
D+
/-,
MO
T_S
PD
L+/-
OP
U
SP
IND
LE/
ST
EP
ING
/S
LED
MO
TO
RLI
MIT
, TR
IN, T
RO
UT,
OP
O, O
P+
/-
16M
bit F
LAS
HIC
4004
ES
29LV
160E
B-7
0TG
MA
0~M
A11
, DQ
0~D
Q15
,D
QM
0, D
QM
1, D
BA
0, D
BA
1,
SD
CLK
, SD
CK
E, D
WE
#,
DR
AS
#, D
CA
S#,
DC
S#
A D
A0~
A20
, AD
0~A
D7,
PR
D#,
PC
E#,
PW
R#D
CS
#
64M
bit S
DR
AM
IC40
05H
Y57
V64
1620
ET
P-6
-CA
A
RE
SE
T IC
IC40
03R
3112
N29
1A-
TR
-FA
AV
IDE
O D
RIV
ER
6C
H IC
IC73
01LA
7305
4-T
LM-E
LET
TE
R, I
/XP,
S_Y
, S_C
,
R/C
R, B
/CB
, G/Y
, CV
BS
A, B
35Y U
CV
BS
/Y/U
/VJ7
302
2V
19C
VB
S
21P
IN C
ON
NE
CT
OR
J810
1
1115R
OU
TG
OU
T
167B
OU
T
3L
4CH
BU
S S
W IC
IC73
02S
N74
CB
T32
57P
WR
D
SQ
UE
EZ
E, V
SE
L1
VS
EL1
6C
VB
S
1R
8
VS
EL1
SQ
UE
EZ
E21
PIN
CT
LB
LAN
KIN
G_O
UT
Q81
01, Q
8102
21 P
IN C
TL
Q81
04, Q
8105
DV
D_R
GB
_H_O
UT
A...
....A
T+
3.3V
B...
....+
1.8V
C...
....P
.CO
N+
5VD
......
.P.C
ON
+6V
E...
....A
T+
12V
F....
...P.
CO
N+
12V
G...
....-
28V
H...
....V
+5H
EE
PR
OM
ICIC
4001
S-2
4CS
08A
FJ-
TB
-1G
EA
IR
IR R
EC
EIV
ER
(O
S65
1)R
OM
-N34
0TA
O
IR
GR
1~G
R8,
P1~
P16
FP
_DI,
FP
_DO
, F
P_S
CK
, ST
BF
IP D
RIV
ER
ICIC
651
PT
6315
FIP
(V
651)
HN
V-0
8SS
44T
GA
A
1CO
AX
IAL
JAC
KJ8
102
CO
AX
IAL
AS
PD
IF
1OP
TIC
AL
OS
8001
OP
TIC
AL
S-V
IDE
O J
AC
KJ7
301
43Y C
C
53S
LLF
E
LS/R
S/S
/LF
E J
AC
KJ8
002
6C
2S
R
L/R
JA
CK
J800
1
32R L
IC80
02/7
/8A
UD
IO L
PF
AN
D A
MP
ICR
C45
80ID
R
DA
C_X
CS
O, S
CK
, SD
,A
CLK
, AB
CK
, ALR
CK
, A
SD
AT0~
2IC80
03/4
/5A
UD
IO D
AC
ICP
CM
1742
KE
G/2
KA
, C
F
US
B_P
OW
ER
1
US
B_F
LAG
2
US
BN
54U
SB
P
A
+5V
1 2U
SB
_DN
3U
SB
_DN
P.C
ON
+5V
21P.
CO
N+
5V
HIG
H S
IDE
SW
IC66
01R
T97
02-P
B
CP
6601
CP
6602
CP
6603
D2+
1 3
D1+
4
D1-
6
D0+
7
D0-
9
CLK
+10
D2-
HD
MI C
ON
NE
CT
OR
CP
5901
CLK
-12
HD
MI_
SC
L
HD
MI_
SD
A
2 13 4
2 13 4
2 13 4
2 13 4
L590
1
L590
2
L590
4
L590
3
TX
2+
TX
2-
TX
1+
TX
1-
TX
0-
TX
0+
TX
C+
TX
C-
HO
TP
LUG
19
PO
WE
R18
SD
A1615
SC
L
Y OUTCB OUTCR OUT
RE
SE
T
SC
LS
DA
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S22
1 2 3 4
4.4 POWER BLOCK DIAGRAM
SW
ITC
HIN
GT
RA
NS
T50
1
P.C
ON
SW
PO
WE
R B
LO
CK
DIA
GR
AM
Q50
5
AC
IN
P.C
ON
+5V
AT+
3.3V
FL
DC
-
-28V
AT+
12V
for
mut
e
P.C
ON
+6V
P.C
ON
+12
V
P.O
N-H
FL
DC
+
Q51
5
P.C
ON
+5V
SW
Q51
0
P.C
ON
+12
V S
W
Q50
4
FL+
P.C
ON
SW
Q50
2
-28V
P.C
ON
SW
VO
LTA
GE
CT
LIC
501
KIA
431A
-AT
PH
OTO
CO
UP
LER
IC50
4P
S25
61A
L1-1
-V (
W)
PO
WE
R C
TL
IC50
2S
TR
-A61
51M
6V R
EG
IC50
3P
Q07
0XF
01S
ZH
RE
G+
1.8V
IC40
06LM
1117
S-A
DJ
+1.
8V
HD
MI+
5V R
EG
ICIC
5902
PQ
1K50
3M2Z
PH
V+
5H
1 2 3 4
C
D
F
A
B
E
23
5 6 7 8
5. DIAGNOSIS5.1 TROUBLE SHOOTING
POWER DOES NOT TURN ON
Is the voltage at pin 8 and pin 9 of CP502 about 3.3V
and at pin 5 of CP502 about 5V?
No
Yes
NoIs there waveform atX4001 about 3.0Vp-p ?
Check X4001, IC4001 and
peripheral circuit.
Yes
Write DVD FIRMWARE DATA.
Check AT+3.3V line of POWER BLOCK.
Check Q515 and peripheral circuit.
No
Yes
No
DECK DOES NOT ACCEPT
OPEN/CLOSE
Check P.CON 6V line of
POWER BLOCK.
YesIs the lose connection
at CD2302 to DECK ?
Check CD2302
connection to DECK.
Change DVD LOADER.
Is the voltage at pin 8,19 and 28 of IC2301
about DC6V ?
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S24
1 2 3 4
DOES NOT LIGHT ON DISPLAY
Yes
Is the voltage at pin 13 and pin 43 of IC651
about 3V ?
Check AT+3.3V line of
POWER BLOCK.
No
Replace V651 or IC651.
NO PLAYBACK PICTURE OF AV
JACK
Is there video signal at pin 33
of IC7301 ?
Change IC7301.
No
Yes
No
Yes
Check J7302 and peripheral
circuit.
Is there a signal at pin 187 of
IC4002 ?
Check IC4002 and
peripheral circuit.
1 2 3 4
C
D
F
A
B
E
25
5 6 7 8
NO DIGITAL AUDIO ON
PLAYBACK OF COAXIAL JACK
Is there waveform at pin 2 of J8102
about 0.3Vp-p?
Check connection at RCA
Cable.
Yes
Yes
No
No
Change IC4002.
Is there waveform at pin 215 of IC4002
about 3.3Vp-p ?
Check Q8103 and
peripheral circuit.
NO ANALOG AUDIO ON
PLAYBACK
Is there AUDIO signal at pins 7 and 8
of IC8003 ?
Yes
Is there waveform at pins 1,2
and 3 0f IC8003 ?
Yes
Yes
Check J8001 and peripheral
circuit.
No
No
Check AT +5V.
Change IC4002.
Is there voltage at pin 6 of IC8003
about 5V ?
No
Change IC8003.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S26
1 2 3 4
THE OUTPUT OF 21PIN DOESN'T
CHANGE (COMPOSITE-RGB)
When 21 pin output is RGB,Is there voltage at pin 16 of
21pin about 4.5V(No load)?
Check 21pin cable and
connection.
Yes
Yes
No
No
Check IC4002 andperipheral circuit.
Is the voltage at pin 188 of IC4002
about 3.3Vp-p ?
Check Q8104, Q8105 and
peripheral circuit.
NO 5.1CH AUDIO ON
PLAYBACK
Is there AUDIO signal at pins 7 and 8
of IC8003, IC8004and IC8005 ?
Yes
Is there waveform at pins 1,2
and 3 0f IC8003, IC8004 and IC8005 ?
Yes
Check J8001, J8002 and peripheral circuit.
No
No
No
Check AT +5V.
Change IC4002.
Is there voltage at pin 6 of IC8003, IC8004
and IC8005 about 5V ?
YES
Change IC8003, IC8004and IC8005.
1 2 3 4
C
D
F
A
B
E
27
5 6 7 8
Symptoms That May Occur When Any Of The Following ICs Is In FailureIC Symptoms
EEPROM(DVD MT PCB Assy : IC4001)
User's data cannot be stored in memory.The ID number is lost.
16M Flash ROM(DVD MT PCB Assy : IC4004)
The power cannot be turned on.Downloading of the firmware cannot be performed.
DVD IC(DVD MT PCB Assy : IC4002)
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be generated, because the DVD processing is performed by a single chip.
64M SDRAM(DVD MT PCB Assy : IC4005)
No power.Block noise is generated during playback.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S28
1 2 3 4
5.2 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY
C40
86
W80
4
R40
28 R4058
W83
2
W822
R23
21
R23
23
R23
20
R23
22
C23
03
C23
02
B40
14
Case when this diagnosis is required : When playback of any disc, including a test disc (DVD: GGV1025, CD: STD-905), cannot be performed
How to diagnoseIn the case mentioned above, degradation of the laser diodes (LDs) mounted on the PICKUP Assy is suspected.Measure the voltage between the two ends of one of the resistors mentioned below.
Measure the voltage between the two ends of R2321 or R2323 on the DVDM Assy. If the voltage is 0.4 V or higher, the 650-nm LD is degraded.
No playback of a DVD :
Measure the voltage between the two ends of R2320 or R2322 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded.
No playback of a CD :
If the measurements show degradation of an LD, replace the PICKUP Assy.
SIDE B
DVD MT PCB ASSY
DMF090A
R40
60
C40
71
C40
80
C40
81C40
82
W82
7
C59
21
C40
88
C40
68
C40
72
C40
73
C40
54
C41
02
C41
01
C41
20
C40
52
C40
64
R40
01
C40
55C
4051
R40
14
R40
04
C40
22
C40
40
C40
25
R4044
C40
21
R40
54
C40
86
C40
29
R40
39
C40
36
W81
3C
4037
C40
38
R4003
C40
01
C40
02
C40
03
C40
20
C40
08
C40
09
R40
05
C41
05
C40
07
C40
05C
4019
C40
13
C40
17
C40
16
C40
15
C40
14
C40
26
W816
R40
20
C40
27C
4028
C40
33
R40
22
C40
34
C40
35
C40
41
C40
43
C40
49
C40
48
C40
46
R40
57R
4053
C40
61
R40
69
R40
68
W82
8
Q4002
R40
48
C40
84
C40
65
R40
06
R4008
C41
10C40
66
C40
67
R7304
R73
05R
7316
R7317
C73
30
C73
17C
7302
C73
13
Q7302R73
15 C73
05
R40
67
C40
83
R40
66
C40
74
R4065
R4064
R40
61
R40
02
W80
4
R80
97
C80
42
C80
54
C80
06
R80
99
C80
51R80
63R
8064
C80
55
R8066
C80
62
C80
46 R8061
R80
75
R80
87
Q8021
C80
05
R80
96
W808
W809
R8084
B80
04
Q8025
R80
83
R8086R80
89
R40
28 R4058
W83
2
W822
W82
1
R4051
C40
30
C40
12
R8004
R4026
R23
21
R23
23
R23
20
R23
22
C23
03
C23
02
R23
18
R2327
W86
8
W85
6R
4009
C41
28
W807
B40
14
W85
7
W85
8
C59
01
B40
15
R8065
C59
25
C23
08
B40
18
Q4004
B40
16
R80
59
W864
W86
2
R8028
C41
31
1 2 3 4
C
D
F
A
B
E
29
5 6 7 8
6. SERVICE MODE6.1 SERVICE MODE PROCEDURE
POWER ON
DSC - &&&
GGF1381Service moderemote controlunit
GGF1381Service moderemote controlunit
<TRAY OPEN> <TRAY CLOSE>
OPEN/CLOSE(Player)
OPEN/CLOSE
Press the play key ( ) of the normal remote control unit.
(Player)
An address is displayed
OR
ESC
<PLAY>ESC TEST
CHECKDVD, CD
DVD disc
POWER
ON
OFF
POWER
DISC SET
Notes:• After going into service mode, if you play back the disc, "DISC-NON" is displayed.• The video signal and the audio signal are outputted during the servicemode.• The SKIP key and the SCAN key are effective during the service mode.
SERVICE MODE: PLAY
SERVICE MODE: OFF
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S30
1 2 3 4
6.2 SERVICE MODE IN
Service Mode Functional Specification1 Service mode entry
In the power ON state, press the [ESC] (A8-5F) key and [TEST / RANDOM] (A8-5E) key in order of the Service mode remote control unit. • Light the all FL and LEDs.• OSD displays test mode.
Note:* When pressing the keys of something, the FL displays "NO DISC" and the LED lighting disappears.
2 Release the Service mode• Turn off the power.• Press the [ESC] (A8-5F) key of the remote control unit.
3 LD ONDVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n).CD : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n).
1 2 3 4
C
D
F
A
B
E
31
5 6 7 8
6.3 DISPLAY SPECIFICATION OF THE SERVICE MODE
Character in bold : Item name: Information display
1
56
1011
89
3
2
12
15
13
14
1 Address indicationThe address being traced is displayed in number. (as for the DVD, indication of decimal number is possible.)DVD : ID indication (hexadecimal number, 8 digits)
[∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]CD : ID indication [∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]
2 Code indication of remote control unit [R – ∗ ∗ ∗ ∗]In case of double code, display a 2nd code.
3 Main unit keycode indication [K – ∗ ∗]
5 Tracking status [TRKG – ∗ ∗ ∗]Tracking on : [ON]Tracking off : [OFF]
6 Spindle status [SPDL – ∗ ∗ ∗][OFF], [CLV]
7 Mechanism (loading) position value [M – ∗ ∗]Unknown : [01] or [41]Open state : [04]Close state : [08]During opening : [12]During closing : [22]
8 Slider position [S – ∗ ∗ ∗ ∗]In Side Switch ON : [01]In Side Switch OFF : [00]
9 Output video system [V – ∗ ∗ ∗ ∗]NTSC system : [NTSC]PAL system : [PAL]Automatic setting : [AUTO]
Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output settingof scart terminal.)
VIDEO : [00] S-VIDEO : [01]RGB : [02]
0 Disc sensing [DSC – ∗ ∗ ∗]The type of discs loaded is displayed.[DVD], [CD ], [VCD], [ ]
- Jitter value [J – ∗ ∗ ∗ ∗] Note:Don't use it.
= Version of the FL controller [FL: ∗ ∗ ∗ ∗]
~ Region setting of the player [REG: ∗]Setting value : [1] to [6]
! Destination setting of the FL controller[MDL: ∗ ∗ ∗ ∗ / ∗ ∗ ∗]Four characters in the front represent code 01.Three characters in the back represent the destination code.J: /J, K: /KU, /KC, /KU/KC, R: /RL/RD, RAM : /RAM, LB: /LB, WY: /WY
@ Version of the flash ROM [VERSION: ∗∗∗∗∗∗∗∗]
7
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S32
1 2 3 4
6.4 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY
• Service mode indication (ESC + CHP/TIM keys)ID AddressThe error rate is always displayed in exponential notation, e.g., ∗.∗ ∗ e - ∗, for both DVDs and CDs.EDC/ID/AV 1 error history (ID Address, EDC/ID Error, last eight errors)
• Calculation of the average error rate (ESC + "5" [Service mode remote control unit] keys)The average of the last eight error rates is calculated and indicated in exponential notation. After the calculation is completed, "OK" or "NG" is displayed. If "NG" is displayed, the disc tray will open (for both DVDs and CDs)For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less
• Indication of model information (ESC + CHAP keys)The items from 12 to 15 of the SERVICE MODE Indications are displayed. However, in the indications, S in the standard test mode is changed to CHIP VERSION, and M is changed to FL VERSION.
• Region confirmation mode (ESC + A.MON [Service mode remote control unit] + "1"-"8" [Service mode remote control unit] keys)After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens.
Command Contents ConditionsRemote Control
Key NameRemote
Control CodeMemory clear and region / revision indication CLEAR (∗1) A8-45
Average value measurement of DVD error rate 5 (∗1) A8-05
CD error rate measurement 5 (∗1) A8-05
Scart terminal output : VIDEO
WY, models equipped with Scart terminal
AUDIO AF-BE
Scart terminal output : S-VIDEO SUBTITLE AF-36
Scart terminal output : RGB ANGLE AF-B5
Progressive OFFOnly for progressive models
R_SKIP A3-9D
Progressive ON F_SKIP A3-9C
ZOOM ON (X2 -> X4 -> x1) ZOOM AF-37
Service mode indication (error rate indication, etc.) CHP/TIM (∗1) A8-13
Model information indication CHAP (∗1) A8-40
Title search Input mode INTitle No. inputSearch execution
SIDE A (∗1)Numbers (∗1)
PLAY (∗1)
A8-4DA8-00 to A8-09
A8-17
Region confimation modeA.MON (∗1)
Numbers (∗1)A8-1E
A8-01 to A8-08
Only during normal playback, the following shortcut keys can be assigned by pressing a required key after pressing the ESC key of the remote control unit. To quit, press the ESC key
∗1 : Service mode remote control unit
1 2 3 4
C
D
F
A
B
E
33
5 6 7 8
6.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE• Display during Service Mode
To enter Service Mode, press the CHP/TIM key while holding the ESC key pressed.To quit, press the ESC key.
Service mode display1 ID Address2 Error rate (always displayed), in exponential notation
ERROR RATE : ∗ ∗ ∗ ∗ ∗ ∗ ∗ ( ∗ ∗ ∗ ∗ )
• Calculation of the average error rate For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less
3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors)
Note:∗ Error of AV1 is not supported in this player.
Number of error
Indication plan contents
Character in bold : Item name: Information display
12
3
ex) For DVDs
• Step 1
%%e -&
%%e -6 : OK%%e -5 : OK%%e -4 : Refer to Step 2%%e -3 : NG%%e -2 : NG
• Step 2
%%e -4
3.0e -4 : OK4.0e -4 : OK5.0e -4 : OK6.0e -4 : NG7.0e -4 : NG
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S34
1 2 3 4
7. DISASSEMBLY7.1 EXTERIOR SECTION
1. REMOVAL OF MECHANICAL PARTS
1-1: TOP CABINET/FRONT CABINET/OPERATION PCB/OPERATION 2 PCB AND OPERATION 3 PCB(Refer to Fig. 1-1)
AND P.C. BOARDS1-3: POWER PCB (Refer to Fig. 1-3)
1. Disconnect the following connectors:(CP502 and CP503).
2. Remove the 2 screws 1.3. Remove the 4 screws 2.4. Remove the Power PCB in the direction of arrow.
1. Remove the 5 screws 1.2. Remove the Top Cabinet in the direction of arrow (A).3. Disconnect the following connector: (CP4002).4. Unlock the 4 supports 2.5. Remove the Front Cabinet in the direction of arrow (B).6. Remove the 12 screws 37. Remove the Operation PCB/Operation 2 PCB an
Operation 3 PCB in the direction of arrow (C).
1-2: USB PCB (Refer to Fig. 1-2)
1. Disconnect the following connectors:(CP6601 and CP6602).
2. Remove the 2 screws 1.3. Remove the USB PCB in the direction of arrow.
Fig. 1-1
(B)
(A)
Top Cabinet
Front Cabinet
(C)
Operation 2 PCB
Operation PCB
Fig. 1-2
USB PCB
(C)
Operation 3 PCB
1
Fig. 1-3
Power PCB
1 1
1
1
22
2
23
3 3 33
333
3
3
1 1
1
2
1
2
2 2
1. Short circuit the position shown in Fig. 1-4 using asoldering iron. If you remove the DVD Deck with nosoldering, the Laser may be damaged.
2. Disconnect the following connectors:(CP2301, CP2302 and CP2303).
3. Remove the 4 screws 1.4. Remove the DVD Deck in the direction of arrow.
1-4: DVD DECK (Refer to Fig. 1-4)
Fig. 1-4
DVD Deck
Short circuit using asoldering iron.
Pick Up PCB
1
1
1
1
1 2 3 4
C
D
F
A
B
E
35
5 6 7 8
NOTE
• Soldering temperature: 320 ± 20˚C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5Cu
1. Before your operation, please read "PREPARATION OFSERVICING".
2. Use the Lead Free solder.3. Manual soldering conditions
4. When Soldering/Removing of solder, use the drawingequipment over the Pick Up Unit to keep the Flux smokeaway from it.
5. When installing the DVD Deck, remove all the solderingon the short circuit position after the connection of Pick UpPCB and DVD MT PCB connector.
1-5: DVD MT PCB (Refer to Fig. 1-5)
1. Remove the 4 screws 1.2. Remove the 4 screws 2.3. Remove the DVD MT PCB in the direction of arrow.
Fig. 1-5
DVD MT PCB
111
1
2
2
22
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S36
1 2 3 4
7.2 DVD DECK SECTION
2. REMOVAL OF DVD DECK PARTS
2-1: TRAY (Refer to Fig. 2-1-A)
METHOD AT NO POWER SUPPLY)
Tray.
1. Set the Tray opened. (Refer to the DISC REMOVAL
2. Unlock the 2 supports 1 and draw it while sagging the
Fig. 2-1-A
Tray
Push to Sag
Push to Sag
Loader Ass'y
1
NOTE
1. In case of the Tray installation, install them as the circledsection of Fig. 2-1-B so that the each markers are met.
2-2: TRAVERSE ASS'Y (Refer to Fig. 2-2-A)
1. Remove the screw 1.2. Unlock the 2 supports 2.3. Remove the Insulator (R) from the Loader Sub Ass'y.4. Remove the Traverse Ass'y.
Fig. 2-2-A
Tray
Loader Ass'y
Fig. 2-1-B
Insulator (R)
NOTE
1. Disassemble only the DVD DECK PARTS parts listedhere. Minute adjustments are needed if the disassemblyis done. If the repair is needed except listed parts,replace the DVD MECHA ASS'Y.
NOTE
1. In case of the Traverse Ass'y, install it from (1) to (4) in
2. In case of the Traverse Ass'y installation, hook the wireorder. (Refer to Fig. 2-2-B)
on the Loader Ass'y as shown Fig. 2-2-C.
1
Traverse Ass'y
Loader Sub Ass'y
Fig. 2-2-BCheck Lock
Traverse Ass'y
Rack Loading
Loader Ass'y (Bottom Side)
Holder Traverse
Fig. 2-2-C
Loader Ass'y
Check Hook
Loading Belt
Loading Sub Ass'y
Gear Pulley
1
2-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT(Refer to Fig. 2-3-A)
1. Remove the Loading Belt.2. Remove the screw 1.3. Remove the Loading Motor PCB Ass'y.4. Remove the 2 screws 2.5. Remove the Loading Motor.6. Remove the Gear Pulley.
Fig. 2-3-A
Loading Motor PCB Ass’y
• Screw Torque: 2.0 ± 0.3kgf•cm
• Screw Torque: 2.5 ± 0.3kgf•cm (Screw 1)• Screw Torque: 1.0 ± 0.3kgf•cm (Screw 2)
22
Loading Motor
2
2
1 2 3 4
C
D
F
A
B
E
37
5 6 7 8
BROWN (1)
WHITE (2)
NOTE
1. In case of the Pulley Motor installation, check if the value
2. When installing the wire of the Loading Motor PCB Ass'y,
3. When installing the Loading Motor PCB Ass'y, install it
4. In case of the Loading Motor PCB Ass'y installation, hook
of the Fig. 2-3-B is correct.
install it correctly as Fig. 2-3-C.Manual soldering conditions• Soldering temperature: 320 ± 20˚C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5Cu
correctly as Fig. 2-3-D.
the wire on the Loader Sub Ass'y as shown Fig. 2-3-E.
Fig. 2-3-B
7.0 ± 0.1mm
Safety surface for pressingof the insert.
Loading Motor
Pulley Motor
Check HookLoading Motor PCB Ass’y
Loading Motor PCB Ass’yFig. 2-3-C
Fig. 2-3-E
Check Hook
Fig. 2-3-D
Rack Loading
BA
The Lever should be positionbetween A and B.
Check Hook
Rack Loading
1
Loader Sub Ass’y
Gear Main
2-4: RACK LOADING/MAIN GEAR/PULLEY GEAR(Refer to Fig. 2-4-A)
1. Unlock the support 2 and remove the Gear Pulley.2. Remove the Gear Main.3. Press down the catcher 1 and slide the Rack Loading.
Gear Pulley
2
Fig. 2-4-A
NOTE
1. In case of the Rack Loading installation, hook the Rack
2. When installing the Gear Main, take care the direction ofLoading on the Loader Sub Ass'y as shown Fig. 2-4-B.
up or down as shown Fig. 2-4-C.
Fig. 2-4-B
Rack Loading
Check Hook
Fig. 2-4-C
Main Gear
Up Side
Down Side
2-5: CLAMPER ASS'Y (Refer to Fig. 2-5-A)
clockwise, then unlock the 3 supports 1.1. Press the Clamper and rotate the Plate Clamper
2. Remove the Plate Clamper, Magnet Clamper and Clamper.
Plate Clamper
Magnet Clamper
Fig. 2-5-A
Main Frame
Clamper1
11
Loader Sub Ass'y (Bottom Side)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S38
1 2 3 4
Holder Traverse
Insulator (F)
Traverse Ass'y
Insulator (F)
Insulator (R)
NOTE
1. In case of the Clamper Ass'y installation, install correctlyas Fig. 2-5-B.
Fig. 2-5-B
Plate Clamper
Clamper
2-6: HOLDER TRAVERSE/INSULATOR (F)/INSULATOR
1. Remove the Holder Traverse.2. Remove the 2 Insulator (F).3. Remove the Insulator (R).
Fig. 2-6-A
(R) (Refer to Fig. 2-6-A)
NOTE
1. In case of the Insulator (F) installation, install correctly as Fig. 2-6-B.
Fig. 2-6-B
Traverse Holder
Insulator (F)
2-7: SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/RACK FEED ASS'Y/FEED MOTOR (Refer to Fig. 2-7-A)
1. Unlock the support 1.2. Remove the Gear Middle.3. Remove the screw 2.4. Remove the Rack Feed Ass'y.5. Remove the screw 3.6. Remove the Switch PCB Ass'y.7. Remove the screw 4.8. Remove the Gear Feed.9. Remove the 2 screws 5.10. Remove the Feed Motor.11. Remove the Gear Motor.
3
Gear Middle
Gear Motor
Feed Motor
• Screw Torque: 1.3 ± 0.3kgf•cm (Screw 2)• Screw Torque: 3.0 ± 0.3kgf•cm (Screw 3)• Screw Torque: 1.0 ± 0.3kgf•cm (Screw 4, 5)
Switch PCB Ass'y
2
4
Rack Feed Ass'y
Gear Feed
5
Fig. 2-7-A
Traverse Ass'y51
NOTE
1. When installing the Rack Feed Ass'y, push both ends to
2. In case of the Gear Motor installation, check if the value
3. When installing the wire of the Switch PCB Ass'y, install
4. After the assembly of the Traverse Ass'y, hook the wire
align the teeth as shown Fig. 2-7-B. Then install it.
of the Fig. 2-7-C is correct.
it correctly as Fig. 2-7-D.Manual soldering conditions• Soldering temperature: 320 ± 20˚C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5Cu
on the Traverse Ass'y as shown Fig. 2-7-E.
[OK] [NG]
Fig. 2-7-B
Rack Feed Ass'y
PushPush
Fig. 2-7-C
8.0 ± 0.2mm
Safety surface for pressingof the insert.
Feed Motor
Gear Motor
Check Lock
Pickup lenesesGEM1004GED-008
1 2 3 4
C
D
F
A
B
E
39
5 6 7 8
[ 24 pin FFC ]
shown from Fig. 2-8.
2-8: FFC WIRE HANDLING
1. When installing the FFC, fold it correctly and install it as
positions for the FFC.1. Do not make the folding lines except the specified
NOTE
Fig. 2-8
Traverse Ass'y
• Loosen the wire in the direcion of the arrow.
Check Hook
Fig. 2-7-E
~ FEED MOTOR ~
WHITE (4)
BROWN (3)
~ SPINDLE MOTOR ~
YELLOW (2)
GREEN (1)
Fig. 2-7-D
Switch PCB Ass'y
Printing Surface Fold
79 ± 1 mm
Reinforcement Plate
To Pick Up PCB
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S40
1 2 3 4
8. EACH SETTING AND ADJUSTMENT8.1 ADJUSTMENT
8.2 RE-WRITE FOR DVD FIRMWARE
There is no information to be shown in this chapter.
1. PurposeAfter replacing the DVD MT PCB Assy, be sure to update the firmware to the latest version. The firmware of the Assy for service may not be the latest.
3. Procedures for updating the firmwareHow to update:1 Turn on the main unit and open the disc tray.2 Place the disc for updating in the disc tray and close the tray.3 Press the PLAY button.
4 Updating of the firmware is completed.
2. Procedures for creating the disc for updatingNecessary tools:1 PC with a CD-R/CD-RW drive2 Blank CD-R or CD-RW3 Firmware file (∗∗∗∗∗.BIN)
How to create:1 Start up the program for writing to CD.2 Load a blank disc in the CD-R/CD-RW drive.3 Enter "PIONEER" as the volume label.4 Select the .BIN file.5 Write the latest version of the firmware in ISO 9660 format.
While the screen shown at left is being displayed, updating is in progress.DO NOT TURN OFF THE POWER DURING UPDATING.
When the screen with the Pioneer logo is displayed, updating is completed.The time required for updating is about 2 minutes.
1 2 3 4
C
D
F
A
B
E
41
5 6 7 8
4. How to confirm the version of the firmwarePress the ESC then the CHAP key on the remote control unit for servicing. The version of the firmware is labeled ROM NUMBER. Check if the version is the latest one.
5. Troubleshooting1 If updating of the firmware failed
If the main unit was turned off during updating, it cannot initialize and start up again properly. In such a case, replace the flash ROM on the DVD MT PCB Assy.
2 If updating of the firmware using the disc for updating failed• Was the disc for updating recognized properly?
Check if the volume label of the disc is PIONEER.• Is playback of a disc other than the disc for updating possible?
If playback of a test CD is also impossible, a reading section, such as PU, may be defective. In such a case, repair the defective part first.If playback of a test CD is possible, the disc for updating may be defective. Check for any scratches or foreign matter, such as fingerprints, on the reading surface.If no problem is found with the disc, create a new disc for updating again.
YGA6B23A
AREA:WY
40
02A5
1.16
1389FE
ROM NUMBER
REGION:2
REG CHK
SUM CHK
FL VERSION
CHIP VERSION
Y G A 6 B 2 3 A
How to interpret the version code:
Number of releases on the same release date
Release date:6: YearB: Month (1-9 [Jan-Sep], A-C [Oct-Dec])23: Day
Fixed
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S42
1 2 3 4
9. EXPLODED VIEWS AND PARTS LIST
9.1 PACKING SECTION
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.The mark found on some component parts indicates the importance of the safety factor of the part.Therefore, when replacing, be sure to use parts of identical designation.Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual.(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
YXZTUR5 Only
YXZTUR5 Only
YXZTUR5 Only
YXZTUR5 Only
WVXZT5Only
ExceptWVXZT5
1 2 3 4
C
D
F
A
B
E
43
5 6 7 8
PACKING SECTION parts List
(2) CONTRAST TABLE DV-600AV-S/WYXZT5, /WVXZT5, /YXZTUR5, DV-600AV-K/WYXZT5 and YXZTUR5 types are constructed the same except for the following :
Mark No. Description Part No.
> 1 Power Cable See Contrast table (2)
2 Audio/Video Cable 06CPBA2006
3 Remote Control 07650NU020
4 Package Pad 792WHAA237
5 Operating Instructions (E) See Contrast table (2)
NSP 6 Warranty Card J2K00102A
7 Operating Instructions (E/I) See Contrast table (2)
8 Operating Instructions (G/F) See Contrast table (2)
9 Operating Instructions (S/D) See Contrast table (2)
10 Operating Instructions (R) See Contrast table (2)
11 Polyethylene Bag,Instruction See Contrast table (2)
12 Gift Sheet 791WHAA183
13 Package See Contrast table (2)
14 Gift Box See Contrast table (2)
15 Polyethylene Bag,INSTA5 791WHAA040
16 Label Safety See Contrast table (2)
17 Caution Label See Contrast table (2)
Mark No. Description Part No.
Mark No. Symbol and DescriptionDV-600AV-S/
WYXZT5DV-600AV-S/
WVXZT5DV-600AV-S/
YXZTUR5DV-600AV-K/
WYXZT5DV-600AV-K/
YXZTUR5
> 1 Power Cable 1206158802 1206138802 1206158802 1206158802 1206158802
5 Operating Instructions (English) Not used J2K40601B Not used Not used Not used
7 Operating Instructions J2K40121B Not used Not used J2K40121B Not used
(English, Italian)
8 Operating Instructions J2K40122B Not used Not used J2K40122B Not used
(German, French)
9 Operating Instructions J2K40123B Not used Not used J2K40123B Not used
(Spanish, Duch)
10 Operating Instructions (Russian) Not used Not used J2K40801B Not used J2K40801B
11 Polyethylene Bag,Instruction JB5KD400 JB5KD200 JB5KD200 JB5KD400 JB5KD200
13 Package 792WHAA227 792WHAA232 792WHAA227 792WHAA227 792WHAA227
14 Gift Box 793WCDD419 793WCDD518 793WCDD419 793WCDD508 793WCDD508
NSP 16 Label Safety Not used Not used 723000D306 Not used 723000D306
17 Carton Label Not used Not used 723000D600 Not used 723000D594
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S44
1 2 3 4
9.2 EXTERIOR SECTION
CONTACT SIDE
NON-CONTACT SIDE
D
D
A
B
E
A
C
E
B
C
1 2 3 4
C
D
F
A
B
E
45
5 6 7 8
EXTERIOR SECTION parts List
(2) CONTRAST TABLE DV-600AV-S/WYXZT5, /WVXZT5, /YXZTUR5, DV-600AV-K/WYXZT5 and /YXZTUR5 types are constructed the same except for the following :
Mark No. Description Part No.
1 DVD MT PCB Assy A2K501A130
2 OPERATION 1 PCB Assy See Contrast table (2)
3 OPERATION 2 PCB Assy A2K401A280
4 OPERATION 3 PCB Assy A2K401ADF0
> 5 POWER PCB Assy A2K503A240
6 USB PCB Assy A2K401ADD0
7 DVD MECHA ASSY A2K001A650
8 Shield,21Pin 761WSA0237
NSP 9 Plate,Bottom 702WSAA201
NSP 10 Sheet,Caution 726000A140
11 Plate,Cover power 755WPAA031
12 Holder,FFC 761WPA0396
13 Cushion,Leg VEB1349
14 Cabinet,Top See Contrast table (2)
15 Spring Earth 743WKAA015
16 Cushion (15x20x16) 8965TS101B
17 Screw,Tap Tite(S)-Bind Wash. 816423063U
18 Screw,Tap Tite(S) (3x5.5) 8107D3055U
19 Screw,Tap Tite(B) (3x6.0) See Contrast table (2)
20 Screw,Tap Tite(B)Pan (3x6) 810913060U
21 Screw,Tap Tite(P) (2.6x8) 811022680U
22 Screw,Tap Tite(P) Bind WH7 8110I2680U
NSP 23 Sheet,Jack 1 722631A185
NSP 24 Sheet,Jack 2 See Contrast table (2)
NSP 25 Sheet,Jack 3 See Contrast table (2)
26 Sheet DVD 7236740001
27 Front Cabi Assy See Contrast table (2)
28 Flap, DVD 712WPAA150
29 Spring, Flap-DVD 743WKA0052
30 Cord Connector (CD502) 06CU2E3301
31 Cord Jumper (CD601) 122H0B1003
32 Cord Jumper (CD7301) 122H0C3002
33 Cord Jumper (CD604) 122H051204
34 Cord Jumper (CD6601) 122H063401
NSP 35 Angle PCB 761WSAA076
36 Screw Pan 810213060U
NSP 37 Sheet Caution 725000A094
38 Spring Earth 753WUAA012
Mark No. Description Part No.
Mark No. Symbol and DescriptionDV-600AV-S/
WYXZT5DV-600AV-S/
WVXZT5DV-600AV-S/
YXZTUR5DV-600AV-K/
WYXZT5DV-600AV-K/
YXZTUR5
2 OPERATION 1 PCB Assy A2K501A270 A2K501A270 A2K504A270 A2K501A270 A2K408A270
13 Cabinet, Top 702WSB0114 702WSB0114 702WSB0114 702WSB0115 702WSB0115
19 Screw,Tap Tite(B) (3x6.0) 8109K3060U 8109K3060U 8109K3060U 8109K3060S 8109K3060S
NSP 24 Sheet, Jack 2 722631A186 722631A186 722631A186 722631A251 722631A251
NSP 25 Sheet, Jack 3 722631A199 722631A199 722631A255 722631A252 722631A260
27 Front Cabi Assy 7A701A898A 7A701A898A 7A701A898A 7A701A947A 7A701A947A
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S46
1 2 3 4
9.3 06 DVD MECHA SECTION
Applying positions AA, AB and AC for the grease are displayed for this section.Check if the correct grease is applied for each position.
NOTE:CLASS MARK
GREASE AA
AB
PART NO.
GEM1018
GYA1001
ACGEM1036
Cannot supply separately.If the repair is needed, replace the LOADER SUB ASS'Y.
PCB610(LOADING MOTOR PCB ASS'Y)
CD2302
Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.If the repair is needed, replace the DVD MECHA ASS'Y.
(SW PCB ASS'Y)
AB
AB
AB
AA
AB
AB
AB
SW1
PCB640
CD2001
SW2
CD2301
AC
AC
AB Lubricating OilGYA1001
DaifreeGEM1036
Pickup lenesesGEM1004GED-008
GreaseGEM1018
Note :
Lubricating OilGYA1001
1 2 3 4
C
D
F
A
B
E
47
5 6 7 8
06 DVD MECHA SECTION parts List
Mark No. Description Part No.
1 • • • • • •
2 Gear,Middle 92P100117A
3 Loading Motor 1515S98004
4 Pulley,Motor 92P100097A
5 FEED Motor 1515S98004
6 Cord Jumper (24P)(CD2001) 122J4O2202
7 Cord Jumper (CD2302) 122H051602
8 Insulator (F) 92P200013A
9 Belt,Loading 92P200015A
10 Insulator (R) 92P200016A
11 Frame,main 92P100119A
12 Tray (R) 92P100151A
13 Holder ,Traverse 92P100125A
14 Gear,Pulley 92P100123A
15 Gear,Main 92P100124A
16 Gear,Feed 92P100116A
17 • • • • • •
18 Plate, Clamper 92P000023A
19 LOADER SUB ASSY (R) 92AAA0024A
20 Clamper 92P100122A
21 Screw,Pan (M1.7x3 P3) 814011730U
22 Screw,Pan (M1.7x2.3 P3) 814011723U
23 Rack,Loading 92P100121A
24 Gear,Motor 92P100088A
25 Feed Rack Assy 92AAA0017A
26 Screw,T-Tite(B) (M1.7x5.0 P3) 813381750U
27 Screw,Gear Feed 92P700007A
28 Cord Jumper (CD2301) 122H061605
29 Switch (SW1) 0515S32003
30 Push Switch (SW2) 0500101036
31 Screw,Tap Tite(P) (2.6x8) 811022680U
32 Sems.Tap Tite(P) (2x8) 816112080U
33 Screw (Bind 2x8) 811022080U
DV-600AV-S5 6 7 8
C
D
F
A
B
E
107 108 109 11
21212213214
R40
30
10TP
4090
TP40
44
C40
840.
1B
C4
0.0B
C
16Y
0330
T5E
ASPD
IFIR
0 2.83.23.3
NCNC0 0 1.7 0
ICE
XRES
ETIR
GPI
O11
GPI
O12
DVD
D18
GPI
O10
GPI
O22
/SD
D0/
INT
3
DV-600AV-S48
1 2 3 4
10. SCHEMATIC DIAGRAM10.1 DVD MT PCB ASSY (1/7)
IC4002MT1389EXE/S-L
MPEG/MICON IC
101 102 103 104 105 106
215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256
110
100
1112
1314
1516
1718
192
2021
2223
2425
2627
2829
330
3132
3334
3536
3738
394
4041
4243
4445
4647
4849
550
5152
5354
5556
5758
596
6061
6263
64
65 66 67 68 69
7
70 71 72 73 74 75 76 77 78 79
8
80 81 82 83 84 85 86 87 88 89
9
90 91 92 93 94 95 96 97 98 99
R4020 15K
R4053
10K
R4039 5.1K
R4059 10K
R40
2710
0
R40
4033
R405710K
R4047 33
R4046 10
R4048 10K
R40
5033
R40
4333
R40
38
33
R40
22
100K
R4025100K
R40
05
680K
R40
3533
R40
0110
K
R4004 10KR4014 10K
R4024
750K
R4015 13K +-1%R4016 8.2K +-1%
R4017 22KR4018 13K +-1%R4019 13K +-1%
R4054 10K
R4026
6.8
TP4039
TP40
43
TP40
41
TP40
37
TP40
36
TP40
34
TP40
33
TP4009
TP4007
TP4001TP4002TP4003TP4004TP4005TP4006
TP4008
TP40
15TP
4016
TP40
17TP
4018
TP40
19TP
4020
TP40
21
TP40
22TP
4023
TP40
25TP
4024
TP40
26TP
4027
TP40
28
TP40
31
TP40
32
TP4108TP4107
TP4103TP40
14
TP4109
TP4013
TP4011
TP40
30TP
4029
TP4010
TP4012
W812
W83
3
W80
7
W815
W83
0
W813
W816
C4033
0.001 B
C4027 0.1 B
C40
320.
1B
C40
37
4.7
(212
5) B
C40
38
0.1
B
C40
42
0.04
7B
C40
440.
047
B
C40
240.
0015
BC4021 0.1 B
C40
310.
033
B
C4001 0.0022 B
C4002 270P CH
C4003 270P CH
C4026 0.1 B
C40
43
0.1
B
C40
41
0.1
B
C40
35
0.1
B
C40470.001 B
C40
34
20P
CH
C40
460.
1B
C40
49
11P
CH
C40
48
12P
CH
C40
61 4.7
(212
5)
B
C40
22
0.1
B
C40
09
0.01
5 B
C40
08
0.1
B
C40
07
0.1
B
C41
05
0.00
22B
C40
30
10
(212
5) B
C40
12
10(212
5) B
C41
31
100P
CH
C40
51 0.1
B
C40
550.
1B
C4028
0.1 B
C4014 1 BC4015 1 BC4016 1 BC4017 1 BC4103 1 B
C4019 0.1 B
C40
25
0.1
B
C4013 0.1 B
C4020
0.1 B
C4005
0.1 B
C40
36
0.1
B
C40
29
0.1
B
C40
63 10
(212
5)
B
IC40
01S-
24C
S08A
FJ-T
B-1G
EEE
PRO
M IC
1 2 3 4
5678
C40
60_1
220
6.3V
YK_P
C40
23 470
6.3V
YK_P
X4001
100GT0272027MHz
Q4004KTC3875S_Y_RTK
STBY POWER CTL
B401
4
MM
Z160
8R10
2CT
B4010
MMZ1608R102CT
B401
6
MM
Z160
8R10
2CT
B4018
MMZ1608R102CT
NR
4001
4D03
WG
J
NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
ACLK
ABC
K
V1P4
V+1R
8
V+3
ALR
CK
V+3
ASD
AT0
ASD
AT1
ASD
AT2
V+3
ADAC
_GN
D
ABCDEF
MDI1LDO1LDO2V1P4
DMSOFMSO
TRCLOSETROPEN
TRSOFOSO
OPOOP+OP-
TROUTTRIN D
STBY AV20
LIMIT B
IOA CRF RF
D_GND
EF
MDI1
LDO2LDO1
V20V1P4
MA0MA1MA2MA3 OPO
MA4 OP-MA5 OP+MA6 DMSOMA7MA8 FMSO
MA9 TROPENMA10 V1P4MA11 TRSO
SDCKESDCLK FOSO
DBA0DBA1DCS# USBP
DRAS#DCAS# USBN
DWE# V+3DQM0DQM1
DQ0DQ1 V+1R8
DQ2DQ3 USB+3DQ4 USB_P_ON-LDQ5DQ6 USB_FLAG
DQ7 IOADQ8DQ9 A2
DQ10DQ11 A3
DQ12 A4DQ13 A5DQ14 A6DQ15
A0 A7
A1 A8A2 A18A3 A19A4A5 SDA
A6 SCLA7 V+3
UW
R#
UR
D#
A8A9
A10A11A12A13A14A15A16A17A18A19A20AD0AD1AD2AD3
PWR
#A1
6A1
5A1
4A1
3A1
2A1
1A1
0
A20
PCE#
PRD
#AD
0AD
1
AD2
AD3
AD4
AD5
AD6
AD7
A17
AD4 A9 A1 A0
AD5AD6AD7
PWR#
FP_S
CK
V+1R
8
FP_D
I
FP_D
O
PCE# STB
SCL
SDA
RXD
TXD
PRD#
3.3
NCNC1.91.41.11.101.51.40.80.80.702.31.32.32.20.81.90.90.33.23.2 0.7 3.23.23.23.23.23.13.23.23.23.23.21.71.8001.30.70 3.23.2
NCNC
NCNC
2.0200
2.012
2.012.011.67
00000
3.180.831.521.67
01.21.281.35
2.06
2.031.27
1.531.54
1.551.271.251.351.321.952.77
01.892.71
3.183.162.38
00
2.03
1.941.94
03.032.251.872.261.61.7
1.75000
3.230
1.720.7
3.190.392.731.72
0
01.6 1.6 1.6 0 0 0 0 0 0.9 3.2 1.601.7 0 01.7 3.3 0 0 03.3 3.3 01.11.6 1.8 01.3 1.2 3.2 03.2 01.5 1.5 1.6 3.1 0 00.8 1.3
FROM/TO LOADER/MOTOR DRIVE
65
66
67
68
254
253
255
256
XIOWR
OSNRFGCIREFAVDD3AGNDDVDADVDBDVDCDVDDDVDRFIPMAMBMCMDSASBSC/TNISD/TPIMDI1MDI2LDO2LDO1SVDD3
RFLVL/RFONSGND
CSO/RFOP
V2REFV20VFEFOEFOTEOTEZISLVOP_OUTOP_INNOP_INPDMOFMOTROPENPWMPWMOUT1/_ADIN0TROFOOAGND18_DMPLLAVDD18_DMPLLUSB_DPUSB_DMVDD33_USBVSS33_USBPAD_VRTVDD18_USBVSS18_USBUSB_XTALO/GPIO15USB_XTALI/GPIO14FG/GPIO16IOA22/GPIO18DVDD18IOA2IOA3IOA4IOA5IOA6IOA7HIGHA0IOA18IOA19
DVDD33
A16
HIGHA7
IOA2
0
IOA0
ADAC
VDD
3
XTAL
O
HRZFC
CRTPLP
RFGND
OSP
RFR
PAC
RFR
PDC
RFV
DD
3AD
CVS
SAD
CVD
D3
LPFO
P
LPFI
PLP
FIN
PLLV
DD
3PL
LVSS
LPFO
N
JITF
NJI
TFO
RFV
DD
18R
FGN
D18
XTAL
I
SAD
CVS
S18
SAD
CVD
D18
ADAC
VSS3
CH
7C
H8
ADAC
VDD
1AD
ACVD
D2
CEN
TER
ALS AL
AVC
MAR AR
SLF
EAD
ACVS
S1AD
ACVS
S2
APLL
CAP
APLL
VSS
APLL
VDD
SPD
IF/G
PIO
23U
P3_5
/TXD
UP3
_4/R
XDU
P3_1
UP3
_0U
P1_7
/SD
AU
P1_6
/SC
LU
P1_5
/VSD
AU
P1_4
/VST
BU
P1_3
/VSC
KU
P1_2
/GPI
O19
DVD
D33
XUR
DXU
WR
DVD
D18
A17
DVS
S33
AD7
ALE
IOA2
1/G
PIO
17AD
6AD
5AD
4AD
3AD
2D
VSS1
8AD
1AD
0XI
OO
EIO
A1XI
OC
S
HIG
HA1
HIG
HA2
HIG
HA3
HIG
HA4
HIG
HA5
HIG
HA6
IOC
E#
VCC
WP
SCL
SDA
NC
NC
NC
GN
D
0.0
0.0
0.0
0.0
3.3
3.3
0.0
IOW
R#
FROM/TO MEMORY
(V+3D)
3.3V
RFV
33RFVDD3
PLLVDD3
41DVD MT PCB ASSY (1/7) (A2K501A130)
1 2 3 4
C
D
F
A
B
E
101 102 103
218219220221
100
R40
38
33
TP40
37
TP40
36
100P
CH
ASD
AT2
ADAC
_GN
D
FP_D
OST
B
SCL
NC33.22 3.23.2
NCC0 0 0 0 0
LFE
ADAC
VSS1
ADAC
VSS2
UP1
_7/S
DA
UP1
_6/S
CL
UP1
_5/V
SDA
49
5 6 7 8
CAUTION : DIGITAL TRANSISTOR
104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193194195196197198199200201202203204205206207208209210211212213214215216217
R4060 33
R40
0810
K
R40
0610
K
R4007
100
R4084
4.7K
R4002
2.2K +-1%
R4061 51K
R4003 33K
R40092.7K +-1%
R40
30
10
R40
0110
K
R4056
100KR4021
10K
R4051 33
R4064 150 +-1%
R4065 150 +-1%
R4066 150 +-1%
R4067 150 +-1%
R4068 150 +-1%
R4069 150 +-1%
R4083 100R4082 33
R4071 33R4070 33
R4052
10K
TP4045
TP4047
TP40
94
TP4038
TP4040
TP4104
TP4042
TP4105
TP4110
TP41
06
TP40
48TP
4051
TP40
52TP
4053
TP40
54
TP40
55TP
4056
TP40
57TP
4058
TP40
59
TP4087
TP4082TP4081
TP4079TP4080
TP4078
TP4076TP4077
TP4088
TP4075
TP4073TP4074
TP4072
TP4070TP4071
TP4069
TP4100
TP4101
TP4102
TP4095
TP4096
TP4097
TP4099
TP4098
TP4083TP4084TP4085TP4086
TP4061
TP4060
TP4067
TP4062
TP4068
TP4066
TP40
63
TP40
90
TP40
44
TP4035
TP40
46
TP40
49TP
4089
TP40
65
W846
W80
7
W80
4
W828
W827
W831
W837
C40
240.
0015
B
C4075 100P CH
C41
14
1B
C4091
0.1 B
C40
670.
1B
C40
661
B
C4080 0.1 B
C40710.1 B
C4082
0.1 B
C4081
0.1 B
C40
54
220P
CH
C40
840.
1B
C4128
0.01B
C4126
2.2
(2125)
B
C40
64
0.1
B
C4072
0.1 B
C4068
0.1 B
C4073
0.1 B
C41
10 100P
CH
C4088 0.1 B
C40830.1 B
C40740.1 B
C40
65
0.1
B
C4076 33P CH
C4077 100P CH
C4078 33P CH
C41
17
100P
CH
C4079 100P CH
C4104
0.01 B
C40690.0056 B
C40
23 470
6.3V
YK_P
C4011
4716VYK_P
IC40
03R
3112
N29
1A-T
R-F
A
RES
ET IC
1 2 3
45
CP400200_6232_011_006_800+
1
10
11
2
3
4
5
6
7
8
9
Q4003KRC407-RTK/P
USB_P_ON-H
B4015
MMZ1608R102CT
B401
4
MM
Z160
8R10
2CT
CP400400_6232_006_006_800+
1
2
3
4
5
6
SDG
Q4002KTK5132U-RTK/P
LEVEL SHIFT
D4003
UDZS3.9B
D4002
UDZS3.9B
NR
4001
4D03
WG
J03
30T5
E
NR40024D03WGJ0330T5E
V+3
SD SCK
V+3A
STBY
TRIN
I/XP
ASPD
IF
XMM
UTE
XAM
UTE
VSEL
1PW
DN
#
TRO
UT
V+1R
8
DAC
_XC
S0
TRC
LOSE
LETT
ERSQ
UEE
ZE
SDSCKDAC_XCS0VSEL1 XAMUTELETTER XMMUTESQUEEZE ALRCKI/XP
V+3V ABCKR/CR ACLKB/CB ASDAT0G/Y ASDAT1CVBS ASDAT2S_C ASPDIFS_Y ARD_GND AL
D_GND
V+5HS_Y V+3HDVDD18PWDN#S_CV+1R8V+3CVBSV+3EV+3AFLDC-G/YFLDC+-28VB/CBADAC_GNDR/CR D_GND
TX2+TX2-TX1+ HDMI_SDA
HDMI_SCLTX1-HPDTX0+TXC-TX0-TXC+TXC+ TX0-TX0+TXC-TX1-TX1+DVDD18TX2-TX2+A_GND
V+3H
USB+3
V+5H
USB_P_ON-LHDMI_SCLHDMI_SDA
HPD USB_FLAG
MA4MA5MA6MA7
USBPMA8MA9
USBNMA11
SDCKESDCLK V+3
RXDMA3TXDMA2
D_GNDMA1MA0MA10DBA1DBA0
DCS#DRAS#DCAS#DWE#DQM1
FP_SCK
FP_DILIMITDQ8 STB
FP_DO
IR
V+3E
FLDC+
-28V
FLDC-
DQ
15D
Q14
DQ
13D
Q12
DQ
11D
Q10
DQ
9
DQ
M0
DQ
7D
Q6
DQ
5D
Q4
DQ
3
DQ
2D
Q1
DQ
0
RESET
V+3
SDA
RXD
TXD
IR
FROM/TO USB
GND
USBN
USB_POWER
USB_FLAG
GND
USBP
DMF090PCB130
FROM/TO POWER PORT
TO AUDIO/JACK
FROM/TO HDMI
TO VIDEO
NC03.23.2.2 1.41.4 1.30.51.21.20.80.71.11.41.31.33.21.41.31.301.72.83.23.3
NC
NC
00
G
FS
00000
000
0
0.3
1.7
1.7
0.60.5
0.33.20.3
0.53.2
00000
000
0
RB
00
3.21.51.81.71.2
1.500.6
02.52.903.11.43.211.3
3.13.10004.91.74.9
0
01.41.61.3
3.20
3.2
00003.23.4
00
0000
00
NCNC3.2 03.1 3.2 3.2 2.9 2.8 3.2 3.3 3.3 3.2 1.0 1.0.9 3.2 1.6 0 0 1.7 0 0 0 0 3.2 3.2
(V+3D)
127
128
192
191
190
189
ICE
XRES
ETIR R
D7
RD
6R
D5
RD
4R
D3
DVD
D33
RD
2R
D1
RD
0R
D15
RD10
RD9
DQM1
XRCS
RA10
RA2
RCLKCKE
RA9RA8
TXCNTXCP
TX0P
TX1P
TX2P
C
DACVDDB
Y
DAC
VDD
C
APLL
CAP
APLL
VSS
APLL
VDD
GPI
O11
GPI
O12
SPD
IF/G
PIO
23
DVD
D18
GPI
O10
GPI
O9
TS_E
RR
OR
DVD
D33
TS_P
WM
TS_S
YNC
TS_C
LKTS
_VAL
IDTS
_DAT
A7TS
_DAT
A6TS
_DAT
A5TS
_DAT
A4TS
_DAT
A3TS
_DAT
A2TS
_DAT
A1TS
_DAT
A0
VREF
DACVSSC
DADVSSBCVBS
DACVDDA
DACVSSA
TX2NAVDD18_TX0
AGND18_TX0
TX1NAGND18_TX1
TX0NAVDD18_TX1
AGND18_TX2AGND33_TX
AVDD33_TXEXT_CAP
AVDD33_VPLLEXT_RES
AGND33_VPLLGPIO8_HPLG
GPIO7_DDC_CLKDVDD18
GPIO6_DDC_DAGPIO5GPIO4
DVDD33RA4RA5RA6RA7
RA11DVSS33
DVDD33RA3
DVDD18RA1RA0
BA1BA0
XRASXCASXRWE
DVDD33GPIO20/SD_CMD
RD8
125
126
RD12
RD11
GPI
O21
/SD
_CLK
DQ
M0
GPI
O22
/SD
D0/
INT
123
124 RD13
RD14
UP3
_5/T
XDU
P3_4
/RXD
UP3
_1U
P3_0
V+3D
NC
V_O
UT
VSS
NC
CT
VDD
3.3 3.3 0
0
1.8V
3.3V
1.9
(CP601)
STB
DGND
DGND
FLDC+
-28V
FLDC-
CLK
DI(M to F)
DO(F to M)
IR
V+3E
FROM/TO DISRLAY
0
03.3
3
2
5
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S50
1 2 3 4
10.2 DVD MT PCB ASSY(2/7)
IC4004 ES29LV160EB-70TG16Mbit FLASH IC
110
1112
1314
1516
1718
192
2021
2223
242526
2728
29
3
3031
3233
3435
3637
3839
4
4041
4243
4445
4647
48
56
78
9
R4044
10K
C4062
0.001 B
C4040
1 B
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
A17 A16
A15DQ0DQ1DQ2 A14DQ3DQ4DQ5 A0 A13DQ6DQ7DQ8 AD7 A12DQ9
DQ10DQ11 A11DQ12DQ13DQ14 AD6 A10DQ15MA0MA1 A9MA2MA3MA4 AD5 A20MA5MA6MA7MA8MA9
MA10 AD4 PWR#MA11DWE#
SDCKEDQM1DQM0
DCAS#DRAS#
DBA1DBA0 AD3
SDCLKDCS#
A0A1A2 AD2 A19A3A4A5 A18A6A7A8 AD1 A8A9
A10A11 A7A12A13A14 AD0 A6A15A16A17 PRD# A5A18A19A20 A4AD0AD1AD2 PCE# A3AD3AD4AD5 A1 A2AD6AD7
PRD#PCE#PWR#
V+3D_GND
FROM POWER PORT
NC
0
0
1.4
2.6
2.6
1.4
1.2
1.6
1.6
3.3
1.3
0.9
1.6
2.5
1.5
1.6
1.3
2.5
1.5
0.8
1.0
1.7
1.6
0.8
0
0.7
0.6
1.2
1.3
1.9
0.7
1.2A16
VSS
VSS
CE#
A0
A15
A14
A13
A12
A11
A9
A8
A10
A19
D7
D14
D6
D13
D5
D12
D4
VCC
D11
D3
D10
D2
D9
D1
D8
D0
NC
NC
NC
NC
NC
NC
NC
OE#
RESET#
RY/BY#
0
D15/A1
NC (WP#/ACC)
0
0.1
0
0
3.3
A7
A6
A5
A4
A3
A2
A1
A18
A17
0.1
1.6
0.7
1.4
1.6
1.3
1.6
1.7
2.5
1.6
NC
NC
NC
NC
WE#
NC
FROM/TO MPEG/MICON/DSP
(V+3D)
BYTE#
DVD MT PCB ASSY (2/7)(A2K501A130)
1 2 3 4
C
D
F
A
B
E
044
0K
A16
A15
A14
A13
A12
A11
A10
A9
A20
PWR#
A19
A18
A8
A7
A6
A5
A4
A3
A2
51
5 6 7 8
IC4005 HY57V641620ETP-6-C64Mbit(4M*16) 166MHz SDRAM IC
110
1112
1314
1516
1718
192
2021
2223
2425
262728
29
3
3031
3233
3435
3637
3839
4
4041
4243
4445
4647
4849
55051
5253
54
67
89
TP4050C41
20
0.1
B
C4123
0.1 B
C4052
0.1 B
C4102
0.1 B
C4101
0.1 B
C40
50
1000
6.3V
YK_P
NOTE : THE DC VOLTAGE EACH PART WAS MEASUREDWITH THE DIGITAL TESTER DURING PLAYBACK.
DQ15 DQ7
DQ14 DQ6
DQ13 DQ5
DQ12 DQ4
DQ11 DQ3
DQ10 DQ2
DQ9 DQ1
DQ8 DQ0
DQM0
DQM1 DWE#
SDCLK DCAS#
SDCKE DRAS#
DCS#
MA11 DBA0
MA9 DBA1
MA8 MA10
MA7 MA0
MA6 MA1
MA5 MA2
MA4 MA3
DMF090PCB130
VSS
DQ0
DQ1
DQ2
DQ15
VSSQ
DQ12
DQ11
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
VSSQ
DQ10
DQ9
VDDQ
DQ8
LDQM
VSS
UDQM
CLK
CKE
NC
A9
A11
A10/AP
A0
A2
A1
A3
VDDVSS
A4
A5
A6
A7
A8
NC/RFUNC
NC
3.3
1.5
3.3
1.5
1.5
0.0
1.5
1.5
3.3
1.5
1.5
0.0
1.5
3.3
2.0
3.3
3.3
3.3
3.3
3.3
1.0
0.0
1.7
1.7
1.7
1.7
3.30.0
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.9
1.7
1.9
0.0
1.5
3.3
1.5
1.5
0.0
1.5
1.5
3.3
1.5
1.5
0.0
1.5
0.0
DQ13
VDDQ
DQ14
WE#
CAS#
RAS#
CS#
BA0/A13
BA1/A12
VDD
VDDQ
VDD
÷ When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
÷ : The power supply is shown with the marked box.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
2312
+-1%
325
+-1%
NC
NC
NC
DV-600AV-S52
1 2 3 4
10.3 DVD MT PCB ASSY(3/7)
ATTENTION : LES PIECES REPAREES PAR UN > ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES.
CAUTION : SINCE THESE PARTS MARKED BY > ARE CRITICAL FOR SAFETY, USE ONES DESCRIBED IN PARTS LIST ONLY.
CP2301LD07T2-24ND-03
PICK-UP(GOLD)
1
10
11
12
13
14
15
16
17
18
19
2
20
21
22
23
24
3
4
5
6
7
8
9
CP230200_6232_005_006_800+
LOADING
1
2
3
4
5
R23
31
150K
R
8.2K
R2313
10K +-1%
R2307
100K
R23
08
10K
R2309
10K
R2306
100K
R23
38
10K
R23
19
150K
R2329
1
R23
42
680K
R2
470
R2304
10K
R2310
10K
R2316
3.3K
TP2303
TP2304
TP2305
TP2306
TP2309
TP2310
TP2311
TP2312
TP2313
TP2314
TP2315
TP2316
TP2317
TP2318
TP2319
TP2308
TP2307
TP2320
TP2321
TP2322
TP2323
TP2302
TP2324
TP2325
TP2326
TP2327
TP2328
TP2330
TP2333
W802
W81
4
C2302
0.1 B
C2311
0.1 B
C2303
0.1 B
C2301
0.1 B
C2323
0.1 B
C23
22
0.00
22B
C2307
0.1 B
C2306
10010V YK_P
Q2301KTC3875S_Y_RTK
VCR_CTL
CP230300_6232_006_006_800+
SLED/SPINDLE
1
2
3
4
5
6
S
DG
Q2307KTK5132U-RTK/P
VCR_CTL
S
DG
Q2306KTK5132U-RTK/P
VCR_CTL
IOA
V+5S
V+5S
F
V20
E
D
C
IOA
RF
B
A
MDI1
T+
T-
F+
F-
LOAD-FM
SO
TRSO
STBY
LOAD+V+6ATROUT
TRIN
OPO
OP-
OP+
LIMIT
MOT_SLED-
MOT_SLED+
MOT_SPDL+MOT_SPDL-
V+3F
MO
T_SL
ED+
MO
T_SL
ED-
T- T+
LOAD+
LOAD-
GND
OPEN
CLOSE
NC
SW(GND)
LIMIT SW
SLD-
SLD+
SPD-
SPD+
VRCOM
TRKG DRV
TRKG RTN
FOCS RTN
FOCS DRV
VCC
D
B
VR780(CD)
VRF(RF_OUT)
SW1(DVD/CD)
C
E
VS
F
GND
A
VR650(DVD)
GND
GND
LD_DVD(650)
LD_CD(780)
PD/GND
NC
0.0
0.00.2
5.0
0.0
0.0
Track
Sled
4.9
0.0
0.0
DVD MT PCB ASSY (3/7)(A2K501A130)
1 2 3 4
C
D
F
A
B
E
R2313
K +-1%
09
K
2310
10K
2316
3K
W802
2311
B
2307
1 B
IOA
53
5 6 7 8
Q2304KTA1504S_Y_RTK
LD DRIV for CD
Q2305KTA1504S_Y_RTK
LD DRIV for DVD
Q2302KTA1504S_Y_RTK
LD DRIV for CD
Q2303KTA1504S_Y_RTK
LD DRIV for DVD
IC2301 AM5766MOTOR DRIVER IC
110
1112
131415
1617
1819
2
2021
2223
2425
2627
28
293
30
45
67
89
R2311
18K +-1%
R2317
8.2K +-1%R2327
10K
R2318
10K
R2312
8.2K +-1%
R23
22
4.7
R23
20
4.7
R23
23
4.7
R23
21
4.7
R2325
470 +-1%
TP2332JG010
JG008
TP2342JG009
TP2341
TP2301
TP2331
TP2329
W806
W805C2312
0.1 B
C2305
0.1 B
C2308
0.01 B
C23
20
100
10V
YK_P
C23
21
100
10V
YK_P
NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
V20ABCD
V+3F EFMDI1LDO2LDO1IOALDO1
V1P4LIMITTROUTTRINSTBYDMSOFMSOTRCLOSETROPENTRSOFOSOLDO2
OPOOP+OP-RF
V+3FV+5SV+6AD_GND
M_GND
V1P4
FOSO
DM
SO
TRO
PEN
TRC
LOSE
MO
T_SP
DL-
MO
T_SP
DL+
LOAD
+
LOAD
-
F+ F-
DMF090PCB130
FROM POWER PORT
FROM/TO MPEG/MICON/DSP
1.52
5.75
1.51
0
2.63
3.03
1.63
3.42
1.85
1.85
5.77
2.42
2.74
1.55
1.28
NC
NC
NC
0.45
5.74
3.49
0
5.74
1.51
1.57
1.52
0
1.39
5.77
2.84
2.73
2.9
2.82
NC
NC
NC
3.3
0
3.3
0
3.33.3
3.12.5 2.5
3.1
2.0 2.0
DVD
RF33
Vcc1
VOTR-
VOTR+
VOSL+
VOSL-
VOFC-
VOFC+
REGO 1
VINSL+
REGO 2
TRB_1
VINFC
REV
FWD
VOTK-
VOTK+
VOLD+
VOLD-
VCTL
Vcc2
GND
VINLD
TRB_2
VINTK
BIAS
MUTE
PGNDPGND
OPOUT
OPIN
Focus
Spindle
DV-600AV-S5 6 7 8
C
D
F
A
B
E
680K
680K
R8036
10K +-1%
R8031
10K +-1%
R8033
10K +-1
1B
C80
52
1B
C80
54
C8040
1000V YK
C80
48
C8041
100V YK_P
C80
47
AGE EACGITAL TE
DV-600AV-S54
1 2 3 4
10.4 DVD MT PCB ASSY(4/7)
ATTENTION : LES PIECES REPAREES PAR UN > DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITESDANS LA NOMENCLATURE DES PIECES.
CAUTION : SINCE THESE PARTS MARKED BY > ARECRITICAL FOR SAFETY, USE ONESDESCRIBED IN PARTS LIST ONLY.
IC80
03PC
M17
42KE
/2K
AUD
IO D
AC (L
,R) I
C
1
10111213141516
2 3 4 5 6 7 8
9
IC80
05PC
M17
42KE
/2K
AUD
IO D
AC (L
s,R
s) IC
1
10111213141516
2 3 4 5 6 7 8
9
IC80
04PC
M17
42KE
/2K
AUD
IO D
AC (C
,Lfe
) IC
1
10111213141516
2 3 4 5 6 7 8
9
D8006
MA111
D8005
MA111
D8004
MA111
CP8001 A2001WV2-2P
(CU223002)
1
2
Q8001KTA1505S-Y-RTK/P
P.CON+3.3V
Q8012KTA1504S_Y_RTK
MUTE CTL
Q8013KTA1504S_Y_RTK
MUTE CTL
Q8014KTA1504S_Y_RTK
MUTE CTL
R80
21
2.2K
R8011
8.2K
R80
28
4.7K
R8003
100
R8002
100
R8001
100
R8023
6.8K
R8022
2.2K
R80
29
4.7K
R8035
10K +-1%
R80
49
680K
R80
65
R80
26
5.6K
R8019 2.2K
R8038 6.8K
R8020
2.2K
R8024 5.6K
R80
09
1K
R80
05
10K
R8008
10
R8007
10
R8006
10
R80
12
22K
R8018
10
R8017
10
R80
27
4.7K
R80
54
R80
25
680K
TP8011
TP8001
TP8002
TP8003
TP8004
W879
W878
W81
9
C80
04
1B
C80
13
0.00
1B
C80
17
1B
C80
301
B
C80
20
1B
C80
34
0.1
B
C8023
330P CH
C8026330P CH
C80
49
C80
37
0.1
B
C80
15
0.1
B
C80
14
0.1
B
C80
39
1B
C80
191
B
C80
02
1B
C80
36
0.1
B
C8025
330P CH
1
C80
29 1000
6.3V YK
_P
C8032
10010V YK_P
C80
28 220
6.3V YK
_P
C80
31
220
6.3V
YK_P
10
C8035
10010V YK_P
C80
27
4716
VYK
_P
C8033
10010V YK_P
C8072
10010V YK_P
C80
16 1025
VKA
_P
IC80
01TC
7SH
U04
FU(T
E85L
_F
INVE
RTE
R IC
1 2 3
45
Q8009KTC3875S_Y_RTK
REF GEN
Q8011KTC3875S_Y_RTK
REF GEN
Q8010KTC3875S_Y_RTK
REF GEN
Q8008KTC3875S_Y_RTK
REF GEN
Q8003KRC407-RTK/P
MUTE CTL
Q8020KRC407-RTK/P
MUTE CTL
Q8007KRC407-RTK/P
MUTE CTL
Q8002KRC407-RTK/P
MUTE CTL
Q8005KRC407-RTK/P
MUTE CTL
Q8006KRC407-RTK/P
MUTE CTLQ8004KRC407-RTK/P
MUTE CTL
B8001
MMZ1608R102CT
D80
03
UD
ZS6.
8B
NOTE : THE DC VOLTWITH THE DI
V+12
AT
XAMUTEXMMUTE
SDSCK
DAC_XCS0ABCK XMMUTE
ALRCK SDACLK
ASPDIF SCK
ASDAT0 DAC_XCS0
ASDAT1 ACLK1ASDAT2
V+5V+3AV+12
V+12ATV+5A
D_GND
ABCK1ASDAT2ALRCKV+5AV+3A3
V+12ATXMMUTESD
V+3A SCKDAC_XCS0V+3A3ACLK1
V+3A2
V+3A1V+5A
AUDIO_LAUDIO_R
GNDABCK1
ASDAT1ALRCKV+5A
ABCK ABCK1 V+3A2
ABCK0
V+12AT
V+12
XAMUTE
SDACLK1 SCK
DAC_XCS0ACLK0
ACLK
ABCK0
ASDAT0
ALRCKV+5AV+3A1
AL AR
TO 21PIN/D-TERMINAL/DIGITAL
(CP8102)
SPDIF
GND
FROM MPEG/MICON/RF-AMP
FROM POWER PORT
TO VIDEO
0
0 2.6
NC
CS
SCK
ZER
OR
ZER
OA
VCO
M
GN
D_A
PCM
MC
K
ZER
OL/
MASI
PCM
BCK
PCM
DAT
A
PCM
LRC
K
GN
DD
VCC
VOU
TL
VOU
TR
VDD
GN
D_A
VCO
M
ZER
OR
ZER
OA
ZER
OL/
MASI
SCK
CS
PCM
MC
KPC
MBC
K
PCM
DAT
A
PCM
LRC
K
GN
DD
VDD
VCC
VOU
TL
VOU
TR
1.60
03.20
0
1.51.6
0.9
2.6 0
00
0
0
5.8
6.312.5
12.5
5.8
6.3
5.8
12.56.3
6.8
6.312.5
NC
0
3.3
4.9
2.5
2.4
2.4
3.1
3.1
0
000
1.6
1.6
1.5
1.5
0
3.3
4.8
2.4
02.4
3.2003.2
3.2
1.6
NC
2.4
1.6 0
1.5
PCM
MC
KC
S
SCK SI
ZER
OL/
MA
ZER
OR
ZER
OA
VCO
M
GN
D_A
VOU
TR
VOU
TL
VCC
VDD
GN
DD
PCM
LRC
K
PCM
DAT
A
PCM
BCK
NC
1.5 0
3.3
4.8
2.4
2.4
02.4
3.2
003.2
3.2
1.6
1.60
1.6
0
0
0
3.20
0
0
3.3 3.3
2.7
NC 1.50 0
1.63.3
GND
VCC
3.0
1.51.6
0.9
VREF_F
VREF_S
VREF_C
1 2 3 4
C
D
F
A
B
E
R8003
100
R8002
100
R8001
100
R
10K
R80
49
1S_Y_RTK
GEN
TE : THE WITH
VREF_F
VREF_S
VREF_C
55
5 6 7 8
H1H2
E
H1H2
EJ8002
RCA-405A-06
LS/RS/C/LFE
1
23
4
56
CAUTION: DIGITAL TRANSISTOR
H1H2
E
J8001RCA-207B-02
L/R
1
23R8041
10K +-1%
R8052
10K +-1%
R8048
18K +-1%
R8053
10K +-1%
R8045
18K +-1%
8035
+-1%
680K
R8061
10K +-1%
R8043
10K +-1%
R8059
18K +-1%
R8055
18K +-1%
R80
65
680K
R8071
220 +-1%
R8077
1KR80
69
22K
R80
70
22K
R8094
220 +-1%
R8096
220 +-1%
R8099
220 +-1%
R8079
1K
R8078
220 +-1%
R8095
220 +-1%
R8050
18K +-1%
R8058
10K+-1%
R80
54
680K
R8076
220 +-1%
R8093
220 +-1%
R8036
10K +-1%
R8031
10K +-1%
R8033
10K +-1%
R8063
10K +-1%
R8064
18K +-1%
R8087
220 +-1%
R8088
1K
R8090
1K
R8091
1KR8080
220 +-1%
R8085
1K
R8082
220 +-1%
R8081
220 +-1%
R80
66
22K
R80
75
22K
R8046
10K +-1%
R8073
1K
R8074
1K
R80
67
22K
R80
68
22K
R8072
220 +-1%
R8092
220 +-1%
TP8019
TP8012
TP8013
TP8017
TP8015
TP8014
W86
8
C80
06
330P
CH
C80
53
100P
CH
C80
49
1B
C80
62
100P
CH
C80
46
560P
CH
C80
67
0.1
B
C80
08
330P
CH
C80
07
330P
CH
C80
59
100P
CH
C80
44
560P
CH
C80
64
0.1
B
C80
57
100P
CH
C80
45
560P
CH
C80
52
1B
C80
56
100P
CH
C80
51
560P
CH
C80
55
100P
CH
C80
54
1B
C80
73
560P
CH
C80
63
0.1
B
C80
43
560P
CH
C80
09
330P
CH
C80
10
330P
CH
C80
38
220P
CH
C80
05
330P
CH
IC80
07R
C45
80ID
R
AUD
IO L
PF&A
MP
IC
1234
5 6 7 8
IC80
08R
C45
80ID
R
AUD
IO L
PF&A
MP
IC
1234
5 6 7 8
IC80
02R
C45
80ID
R
AUD
IO L
PF&A
MP
IC
1234
5 6 7 8
C8058
4716V YK_PC8040
10010V YK_P
C8061
4716V YK_P
C80
48
100
10V
YK_P
C8066
4716V YK_P
C8041
10010V YK_P
C80
68
4716
VYK
_P
C80
50 100
10V YK
_P
C8065
4716V YK_P
C8060
4716V YK_P
C80
47
100
10V
YK_P
C8069
4716V YK_P
Q8021KTC2875-B
MUTE SW
Q8023KTC2875-B
MUTE SW
Q8017KTC2875-B
MUTE SW
Q8018KTC2875-B
MUTE SW
Q8019KTC2875-B
MUTE SW
Q8024KTC2875-B
MUTE SW
Q8016KTC2875-B
MUTE SW
Q8015KTC2875-B
MUTE SW
DC VOLTAGE EACH PART WAS MEASURED THE DIGITAL TESTER DURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
V+12
CEN
TER
SL SR LFE
AUD
IO_R
AUD
IO_L
AL AR
L R SL SR C LFE
DMF090PCB130
0.60
0
0
0
-0.7
00
-0.7
0
0
-0.7
0-0.7
0
0
00.6
5.7
5.7
5.7
0
+-
-+
+VS
-VS
5.7
5.7
12.25.7
+-
-+
+VS
-VS
0 5.7
5.7
5.7
12.25.7
5.7
5.7
+-
-+
+VS
-VS
5.7
5.7
5.7
5.7
5.7
5.7
12.2
0
00.6
0
0
0.60
10
11
8
9
6
7
DVD MT PCB ASSY (4/7)(A2K501A130)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S56
1 2 3 4
10.5 DVD MT PCB ASSY(5/7)
IC7301 LA73054VIDEO DRIVER 6CH IC
110
1112
1314
1516
1718 19
2
2021
2223
2425
2627
2829
3
3031
3233
3435
36
45
67
89
R7315
1K
TP7303
TP7302
W877
W889
C7309
1 B
C7308
1 B
C7313
0. 1 B
C7302
0. 1 B
C7317
0. 1 B
C7305
1 B
C7307
1 B
C7306
1 B
C7304
0. 1 BC
7319 10
010
V YK_P
C731210010V YK_PQ7302
KRC407-RTK/P
P-H/I-L
NOTE : THEDURING PLAYBACK.MEASURED WITH THE DIGITAL TESTER DC VOLTAGE EACH PART WAS.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
CVBS
SQUEEZE
LETTER
AUDIO_LS_C
AUDIO_R
S_YSQUEEZE
VSEL1LETTER
CVBSS_C VSEL1
S_YG/Y G/Y
B/CBR/CRI/XP
B/CB
R/CR
I/XP
P-H/I-L
V+3FV+5
D_GND
V+6A
VSEL
1
FROM POWER PORT
FROM/TO MPEG/MICON/RF-AMP
FROM AUDIO/JACK
0
0
3.41.2
0
2.8
0
0
5
2.9
0
0
0
2
0
0
2
5
0
0
0
2.5
2.4
2.5
0
2.8
5
0
2.6
0
0
2.7
0
2.8
0
0
0
2.7
5
+5V
GND
(1D=H,2D=L)
(1D=H,2D=L)DRIVE2
(ON=H,OFF=L)
(ON=H,OFF=L)
(9dB=H,6dB=L)
(P=H,I=L)
(RGB=H,YUV=L)
(MIX=H,OFF=L)
(9dB=H,6dB=L)
LPF
IN SW
AMP1
DRIVE1
VCC21
CVBS out
GND21
C out
C-DC out
GND22
Y1 out
GND23
GND24
Y2 out
VCC22
CB out
GND25
CR out
GND26
REG
GND12
CR in
AMP2
CB in
MUTE2
Y2 in
YC-MIX
Y1 in
GND11
C in
LE
SQ
MUTE1
CVBS in
VCC1
DVD MT PCB ASSY (5/7)(A2K501A130)
1 2 3 4
C
D
F
A
B
E
57
5 6 7 8
CP7301 IMSA-9604S-12CVIDEO/AUDIO for 21PIN
1
10
11
12
2
3
4
5
6
7
8
9
J7304DIN-409A
S-VIDEO OUT for HE12
34
56
IC7302 SN74CBT3257PWR4CH BUS SW IC
1
1011
1213
1415
16
23
45
67
8 9
D73
08
MA1
11
D73
11
MA1
11
D73
07
MA1
11
D73
10
MA1
11
D73
09
MA1
11
D73
12
MA1
11
H1H2
E
H1H2
E
J7302RCA-405A-08
CVBS/Y/U/V
1
23
4
56
CAUTION : DIGITAL TRANSISTOR
R73
16
75+-
1%
R73
19
1.2K
R73
20
1.2K
R73
21
1.2K
R73
05
75+-
1%
R73
03
75+-
1%
R73
01
10K
R73
17
75+-
1%
R73
02
75+-
1%
R73
04
75+-
1%
TP7301
C73
30
0.1
B
C73
22
0.00
1B
C73
29
470
6.3
VYK
_P
C73
18 1000
6.3
VYK
_P
C73
16 1000
6.3
VYK
_P
C73
15 470
6.3
VYK
_P
C73
14 470
6.3
VYK
_P
B730
1
MM
Z160
8R10
2CT
B730
5
MM
Z160
8R10
2CT
B730
4
MM
Z160
8R10
2CT
B730
2
MM
Z160
8R10
2CTVS
EL1
AUD
IO_R
AUD
IO_L
SQU
EEZE
21PIN-G/D-Y
21PIN-B/D-U
21PIN-R/D-V
P-H/I-L_RGB-H
ASP/FS
FROM/TO POWER
RGB-H
R
B
G
GND
CVBS
AUDIO R
GND
AUDIO L
FS
GND
GND
C Y
CVB
S
VU Y
ASP
S_Y
S_C
CVBS
3.33.3
1.8
2.4
2.6
1.3
2.5
2.5
2.4
2.4
1.3
5.0
0
0
GND
VCC
2B1
2B2
2A
1B2
1A
4B1
4B2
4A
3B1
3B2
3A
/OE1B1
S
NC
NC
NC
DMF090PCB130
15
14
12 13
17 16
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S58
1 2 3 4
10.6 DVD MT PCB ASSY(6/7)
W861
W856
W855
NOTE : THE DC VOLTAGE EACH PART WASMEASURED WITH THE DIGITAL TESTERDURING PLAYBACK.
V+5HD_GND
TX2+TX2-TX1+TX1-TX0+TX0-
TXC+TXC-HPD
HDMI_SCLHDMI_SDA
A_GND
A_GND
FROM/TO MPEG/MICON/DSP
FROM POWER PORT
DVD MT PCB ASSY (6/7)(A2K501A130)
1 2 3 4
C
D
F
A
B
E
59
5 6 7 8
CP5901 1903015-3HDMI CONNECTOR
1
10
11
12
13
14
15
16
17
18
19
2
3
4
5
6
7
8
9
L5901EXC24CG900U
1
2 3
4
L5902EXC24CG900U
1
2 3
4
L5903EXC24CG900U
1
2 3
4
L5904EXC24CG900U
1
2 3
4
R59
19
1.5K
R59
20
1.5K
W840
W851
W858
W850
W857
W862
W864
C59
20
0.1
B
C59
21
10(212
5)
B
C59
25
100P
CH
C59
01
0.01
B
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
TX2+
TX2-
TX1+
TX1-
TX0+
TX0-
TXC+
TXC-
HDMI_SCL
HDMI_SDA
HPD
V+5H
D2+
D2-S
D2-
D1+
D1-S
D0+
D0-S
D0-
CLK-S
CLK-
CEC
SCL
SDA
GND
POWER
HOTPLUG
NC
D1-
CLK+
DMF090PCB130
NCNC
TX2+
TX2+
TX1+
TX1-
TX0+
TX0-
TXC-
TXC+
MP MODIFY
DV-600AV-S5 6 7 8
C
D
F
A
B
E
0.00
1B
C41
00
NOTE
DV-600AV-S60
1 2 3 4
10.7 DVD MT PCB ASSY(7/7)
ATTENTION : LES PIECES REPAREES PAR UN > ETANTDANGEREUSES AN POINT DE VUE SECURITEN’UTILISER QUE CELLS DECRITESDANS LA NOMENCLATURE DES PIECES.
CAUTION : SINCE THESE PARTS MARKED BY > ARECRITICAL FOR SAFETY,USE ONESDESCRIBED IN PARTS LIST ONLY.
C40
95 476.
3VKA
_P
IC4006
LM1117S-ADJ
REG+1.8V IC
123
CP4003A2001WV2-14P
1
10
11
12
13
14
2
3
4
5
6
7
8
9
R4012
68 +-1%
R40
13
39+-
1%
R4011
12
TP4064
W820
W843
C40
99
C40
98
1B
C40
86
1B
C40
93
1B
C40
94
0.1
B
C40
96
1B
C41
12
0.00
1B
FROM/TO POWER
(CP502)
GND
GND
P.CON+5V
STBY L
FL DC-
FL DC+
AT+3.3V
P.CON+12V
AT+12V for MUTE
GND(M)
GND(D)
P.CON+6V
AT+3.3V
-28V
ADJVIN VOUT
1.8 0.63.3
+3.3V
DVD MT PCB ASSY (7/7)(A2K501A130)
1 2 3 4
C
D
F
A
B
E
20
C40
98
61
5 6 7 8
IC5902 PQ1K503M2ZPHHDMI+5V REG(300mA) IC
12
3 45
6
R4058
100
R59
21
22K
R59
01
10K
R40
28
10K
W841
W821
W822
W832
W842
W826
W839
C40
99
0.00
1B
1B
C59
24
0.1
B
C59
22
1B
C40
56
0.01
B
C4119
100P CH
C59
23
0.01
B
C41
00
470
6.3V
YK_P
B4001
MMZ1608R102CT
B4002
MMZ1608R102CT
NOTE : THE DC VOLTAGE EACH PART WASMEASURED WITH THE DIGITAL TESTERDURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
V+3AV+5A V+5AV+5 V+5
V+12AT V+12ATV+12 V+12
D_GND
V+5D_GND
V+6A V+6AV+5S V+5SV+3F V+3F
D_GND
M_GND
V+5H V+5H
V+5HV+3H V+3H
DVDD18 DVDD18
ADAC_GND
V+3 V+3V+3E V+3E
V+1R8 V+1R8
PWDN#
FLDC-
FLDC+
-28V
D_GND
D_GND
DMF090PCB130
TO HDMI
FROM/TO MPEG/MICON/DSP
FRROM/TO MEMORY
TO LOADER/MOTOR DRIVE
TO VIDEO
TO AUDIO/JACK
(CORE)
(MPEG/SDRAM/FLASH)
(FIP/LED/IR/RESET)
VOUT
GND
NRON/OFF
GND
VIN5.8
0
5.4
5
0
1.2
(OPU)
(MOTOR)
(F/E)
(HDMI)
(AUDIO AMP)
(AUDIO MUTE)
(VIDEO/OPT/COAX)
(AUDIO DAC)
(HDMI)(HDMI)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
145
1 42
15167
TP66
2C
675
C65
3
P5 P4 P3 P2
P16
GR
1
12
-15.6
44
-16.0
GN
P16
P15
GR
2
GR
1
G
R
P5 P4 P3
3.3
3.3
268
-26.
8
-26.
8
-20.
5
DV-600AV-S62
1 2 3 4
10.8 OPERATION 1 and OPERATION 2 PCB ASSYS
IC651PT6315
FIP DRIVER IC
116171819202122
2324
2526
2728
2930
3132
33
34 35 36 37 38 39 40 4
Vout
B+
GND
OS651
ROM-V340TAO
1
2
3
SW66
4
EVQ
11L0
5R
-SKI
P
SW66
2
EVQ
11L0
5R
+SKI
P
SW66
0
EVQ
11L0
5R
STO
P
SW668
EVQ11L05R
USB
SW667
EVQ11L05R
POWER
SW652
EVQ11L05R
DOWN
SW658
EVQ11L05R
TOPMENU
SW656
EVQ11L05R
MENU
SW655
EVQ11L05R
RETURN
SW653
EVQ11L05R
ENTER
SW654
EVQ11L05R
RIGHT
SW657
EVQ11L05R
UP
SW659
EVQ11L05R
LEFT
SW661
EVQ11L05R
HOMEMENU
SW666
EVQ11L05R
EJECT
SW66
5
EVQ
11L0
5R
PAU
SE
SW66
3
EVQ
11L0
5R
PLAY
V651 HNV-08SS44T
118192021222324252627283132
D660
LTL-1CHEE-002A
HDMI LED(RED)
CD
604
2H05
1204
FFC
(1.0
mm
pitc
h)
D651 1SS133
D654 1SS133
D656 1SS133
D658 1SS133
D665 1SS133D659 1SS133
D657 1SS133
D655 1SS133
D652 1SS133
CP6
0500
_623
2_00
5_10
2_80
0+
1 2 3 4 5
CP6
0400
_623
2_00
5_10
2_80
0+12345
R664
330 1/4W
R666
2.2 1/4W
W80
8
W80
7
C65
1
0.1
B
C67
4
476.
3VKA
_P
NOTE : THE DC VOLTAGE EACH PART WASMEASURED WITH THE DIGITAL TESTERDURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
P16
P15
P14
P13
P12
P11
P10
P9 P8 P7 P6
P8 P9 P10
P11
P12
P13
P14
P15
P7
P6
P5
P4
P3
P2
P1
SW1 GR
8
GR
7
GR
6
GR
5
GR
4
GR
3
GR
2
V+3E
LED
IR
SW2
DEF130PCBDF0
23
-12.0
-6.0
-18.0
-19.0-19.0-9.5-13.0-9.5-12.6-13.0-6.0
34
NC
NC
NC
NC
-18.0
-18.0
-18.0
-18.0
-18.0
-18.0
-18.0
-18.0
-16.0 -16.0 -16.0-16.0P1
4
P13
P12
P11
P10P9P8
P7P6
GR12
P5
P4
P3
P2
P1
-28V
GR10
GR11
GR9
GR
8
GR
7
GR
6
GR
5
GR
4
GR
3-16.0-18.0-18.0-18.0
FL+
FL+
P16
P15
P14
P13
P12
P11
P10
DVDCD TRACK ALL
P9 P8 P7 P6-2
0.5
-22.
7
-20.
5
-20.
5
-22.
7
-26.
8
-26.
8
-20.
5
-22.
7
-22.
7
-26.
8
-19.
7
-19.
7
DEF129PCB280
SW2
POW
ER
V+3E
LED
USB
SW2
POW
ER
V+3E
LED
USB
OP
ER
AT
ION
2 P
CB
AS
SY
(A2K
401A
280)
OPERATION 3 PCB ASSY(A2K401ADF0)
1 2 3 4
C
D
F
A
B
E
C651T6315
DRIVER IC
1718
38 39
202122
66
1/4W
P10
P9 P8
P12
P13
GR
5
GR
4V+
3E
-19-9.5
-16.0 -16
P13
P12
GR
5
GR
4
P10
CK AL
P9 P8-2
0.5
-20.
5
-22.
7
63
5 6 7 8
110
11
1213141516
23
4
40 41 42 43 44
56
78
9
110111213141516171819 256789
CD6012H0B1003
FFC(1.0mm pitch)
D66
9
1SS1
33
MS1
_2
R65
7
10K
R65
8
10K
R65
5
1K R65
6
1K
R662
100K
R653
2.2
R652
2.2
R651
2.2
R654
2.2
TP66
2
TP663
W805
W80
9
C61
1_1
47P
CH
C61
0_1
47P
CH
C67
6
0.1
B
C65
8
0.1
B
C67
5
0.1
B
C604
33P CHC605
0.001 B
C65
3
476.
3VKA
_P
CP60100_6232_011_102_800+
1
10
11
2
3
4
5
6
7
8
9
FLDC-
FLDC+
P7 P6 P5 P4 P3 P2 P1 GR
8
GR
7
GR
6
GR
5
GR
4
GR
3
GR
2
GR
1
SW2
-28V
SW1
P14
P15
P16
STB
FP_SCK
FP_DI
FP_DO
GR
3
GR
2
GR
1
LED
FP_SCK
FP_DI
STB
FP_DOV+3E IR
V+3E
FLDC+
-28V
FLDC-
GND
PCB270DEF126
STB
12
VDD
3.2
0
0
0-19.0 -15.6.0
LED1
LED2
LED4
CLK
VDD
44
.0 -16.0 -16.0 0
0
2.9
3.2
0.7
3.4
NC
K2
K1
DI
DO
OSC
GND
P16
P15
P14
GR
3
GR
2
GR
1
GND
LED3
0
0
0
NC
NC
NC
FL-
FL-
L REPEAT A B
P7 P6 P5 P4 P3 P2 P1 G8
G7
G6
G5
G4
G3
G2
G1
3.3
3.3
-25.
1
-25.
1
-25.
1
-25.
1
-25.
1
-25.
1
-25.
1
-25.
1
-20.
5
-26.
8
-26.
8
-26.
8
-20.
5
-20.
5
-22.
7
-22.
3
-22.
3
DGND
DGND
FLDC+
-28V
FLDC-
DI (M to F)
V+3E
STB
DO (F to M)
IR
CLK
(CP4002)
FROM/TO MPEG/MICON/RF-AMP
1
SwitchesSW652 : DOWNSW653 : ENTERSW654 : RIGHTSW655 : RETURNSW656 : MENUSW657 : UPSW658 : TOPMENUSW659 : LEFTSW660 : STOPSW661 : HOMEMENUSW662 : +SKIPSW663 : PLAYSW664 : -SKIPSW665 : PAUSESW666 : EJECT
OPERATION 1 PCB ASSY (WYXZT5, WVXZT5 types : A2K501A270)(YXZTUR5 types : A2K504A270)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
R510_1
2.7 1W
R
68
R51
7
C52
3
470
25V
YKP
C52
1
9
D527
SR240-F
D510
SR290-F
512_1
1H3-E
R51
8R
516
514
1/4W
503
B
C51
7
N
DV-600AV-S64
1 2 3 4
10.9 POWER PCB ASSY (1/2)
NOTE : THE RESISTOR MARKED F IS FUSE RESISTOR.THE ALUMI ELECTROLYTIC CAPACITOR MARKED NPIS NON POLAR ONE.
F501T1.6A_L_250V
51MS016L
L501SS11V-03550-CH
COIL,LINE FILTER
1 2
3 4
FH501EYF-52BCY
FH502EYF-52BCY
IC504PS2561AL1-1-V(W)
PHOTO COUPLER
123
4
R50
2
1.5
1W
1.6A 250V
1.6A 250V
CAUTION : FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE ONLY WITH THE SAME TYPE FUSE1.6A 250VF501
ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIEN’UTILISER QUE DES FUSIBLE DE MEME TYPE1.6A 250VF501
IC501KIA431A-AT
VOLTAGE CTL IC
123
R507
10 1/4W
J501YKE31-0148N
AC INLET
12
T50181291354
10
11
12
13
14
15
16
2
3
4
6
7
8 9
CD501_206158802
AC220V-240V_50Hz/60Hz(EU)
ATTENTION : LES PIECES REPAREES PAR UN > ETANTDANGEREUSES AN POINT DE VUE SECURITEN’UTILISER QUE CELLS DECRITESDANS LA NOMENCLATURE DES PIECES
CAUTION : SINCE THESE PARTS MARKED BY > ARECRITICAL FOR SAFETY,USE ONESDESCRIBED IN PARTS LIST ONLY
C51
1
8240
0VU
P_P
D506
1N4005-EIC
D505
1N4005-EIC
D51
1
1H3-
E
D513
1H3-E
D50
9
RL1
06F-
E
D503
1N4005-EIC
D502
1N4005-EIC
D515
1S40-E
D51
1F5-E
D
R50
3
1.5M
1/2W
R505
22 1/4W
R515
1K
R
1K
R50
4
680K
R51
2_1
100K
1/2W
R513
6.8K 1/4W
C50
5
100P
2KV
R
C514
470P500V B
C50
2_1
0.22
275V
ECQ
UL
C51
6
0.00
2225
0VKX
C51
8
0.00
125
0VKX
C51
3
47P
2KV
SL
C51
5_1
0.01
400V
ECQ
P
C50
8
680P
CH
C540
0.0068 B C
0.1
IC50
2ST
R-A
6151
M
POW
ER C
TL IC
1 2 3 4
5678
C50
9
1050
VYK
_P
C50
6
2.2
50V
KA_P
B501
W4B
RH
3.5X
6X1.
0X2
D50
8
MTZ
J5.6
B
PAL/NTSC
NN
L
NC
0
0
0
0
0
0
0
130
130
0
130
0
-22.5
-22.5
NC
NCDD
OC
P
VCC
GN
D
FB/O
LPST
ARTU
P
17.5 3.90.1
130 130 130
0
0 NC
0 2.59.9
GNDOUT IN
9.90
3.9 10.9
CHASSIS GND
POWER PCB ASSY (1/2)(A2K503A240)
* The parts except mark cannot be changed. On that occasion, replace whole Assy.
PRIMARY side
1 2 3 4
C
D
F
A
B
E
ICKIA
VOLTA
3
R515
1K
R513
6.8K 1/4W
0.0
2.5
2.5
9.9
OUT
65
5 6 7 8
L503
22uH TSL0808
L505
22uH
R529
220 1W
R510_1
2.7 1W
501431A-AT
GE CTL IC
12
R511
68 1/4W
Q506KTA1504S_Y_RTK
PROTECT
PH50
300
3P-2
100
1
IC503PQ070XF01SZH
+6V REG (DVD MOTOR) IC
1 2 3 4
IC505PQ070XF01SZH
+5.2V REG (USB) IC
1 2 3 4
C52
0
100
50V
YK_P
CD73012H0C3002
FFC(1.25mm pitch)
CD502CU2E3301
CORD CONNECTOR
R51
7
1.2K
1/4W
+-1%
R546
3.3K 1/4WM +-1%
CP504 A2001WV2-4PUSB POWER
1
2
3
4
CD6003TD-OR0201R
TM60107650NU020
BT601
R6P(AR)XICI
UM-4
C52
6
470
6.3V
YK_P
C52
3
470
25V
YK_P
C53
6
220
6.3V
YK_P
C53
1
100
16V
YK_P
C53
5
330
16V YK
_P
C52
1
1000
16V
ZL_P
CP502A2001WV2-14P
1
10
11
12
13
14
2
3
4
5
6
7
8
9
CP503IMSA-9604S-12C
A/V for 21PIN
1
10
11
12
2
3
4
5
6
7
8
9
D52
5
1SS1
33
D52
0
1SS1
33D
521
1SS1
33D
522
1SS1
33
D516
1SS133
D534
1SS133
D515
1S40-E
D519
1F5-E
D527
SR240-F
D510
SR290-F
D512_1
1H3-E
CAUTION: DIGITAL TRANSISTOR
Q510 KTA1281_YP.CON+12V SW
Q504KTA1281_Y
FL+ P.CON SW
Q513KTA1504S_Y_RTK
FL+ CTL
Q503KTA1504S_Y_RTK
-28V CTL
R54
0
680
R54
3
4.7K
+-1%
R52
3
22K
R547
22
R51
8
3.3K
+-1%
R51
6
10
R53
9
4.7K
1/4W
R527
100 1/4W
R50
6
100
R53
8
22K
R514
1K 1/4W
R545
22K +-1%
R52
4
1K1/
4W
R51
9
3.3K
R50
9
1K
R53
0
560
1/4W
R537
1K
R53
6
10K
R54
4
10K
R534
100 1/4W
R525
100
R52
6
6.8K
+-1%
R548
1K
R528
22K 1/4W
R53
1
10K
R54
1
5.6K
+-1%
R54
2
470
+-1%
R53
5
4.7K
+-1%
R53
3
15K
+-1%
R55
0
68
W817
W81
4
W825
W81
9
C50
1
0.01
B
C541
0.01 B
C540
068 B C503
0.1 B
C52
7 100
10V YK
_P
C50
4
1025
VKA
_P
C52
8 2.2
50V KA
_P
C51
7
220
25V
YK_P
C53
8
220
6.3V
YK_P
C52
2
1000
6.3V ZL
_P
C51
9 2235
V YK_P
C53
010
010
V KA_P
Q501KTC3875S_Y_RTK
PROTECT
Q509KTC3875S_Y_RTK
REG+12V CTL
Q511KTC3875S_Y_RTK
REG+12V CTL
Q512 KTC3875S_Y_RTKFL+ CTL
Q502 KTC3209_Y-28V P.CON SW
Q515 2SD1835S/T-AAP.CON+5V REG
Q505KRC102SRTK
P.CON SW
B502
W5RH3.5X5X1.0
(W023)D
523
MTZ
J3.6
B
D53
5
MTZ
J5.1
B
D53
6
MTZ
J3.0
B
D533
MTZJ2.2B
D53
1
MTZ
J27B
D52
8
MTZ
J5.1
B
D51
7
MTZ
J2.2
B
NOTE : THE DC VOLTAGE EACH PART WASMEASURED WITH THE DIGITAL TESTERDURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
GND
P.CON+D5VAT+3.3VP.CON+12VAMP_A_OUT_RAMP_A_OUT_LG/Y_VIDEOB/U_VIDEOR/V_VIDEOCVBS/C_VIDEOP-H/I-L_RGB-HASP/FS
A_GND
G/Y_VIDEO
B/U_VIDEO
R/V_VIDEO
P-H/I-L_RGB-H
ASP/FS
CVBS/C_VIDEO
AMP_A_OUT_L
AMP_A_OUT_R
PCB240DPF015
(CP4003)
FROM/TO VIDEO JACK
FROM/TO POWER PORT
NC
0
9.9
0
3.2
0
3.2
FROM/TO 21PIN/D-TERMINAL/DIGITAL
P.CON+12V
P.CON+5V
FL DC-
FL DC+
GND
GND
AT+12V for MUTE
P.CON+6V
-28V
GND(M)
GND(D)
AT+3.3V
AT+3.3V
P.ON-H(STBY L)
0 2.5
GND IN
4.5
12.35.0
4.5
12.95.1
12.6
12.3
12.9
GND
GND
USB+5V
USB+5V
GND
AUDIO L
GND
AUDIO R
RGB-H
CVBS
FS
G
B
R
GND
GND
(CP7301)
19.0
0.6
0
20.8
28.4
28.4
27.8
5.8
5.17.0
6.80.6
0
21.521.6
19.719.0
20.7
FROM/TO USB PCB
ACCESSORY
0
02.8
IN GNDOUT ADJ
7.0 5.9 0 1.2
IN GNDOUT ADJ
0 1.25.9 5.2
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S66
1 2 3 4
10.10 POWER PCB ASSY (2/2)
D81
01
1SS3
55
D81
02
MA1
11D
8104
MA1
11D
8106
MA1
11
D81
05
MA1
11D
8107
MA1
11
D81
03
MA1
11
Q8102KTA1504S_Y_RTK
21PIN CTL DRV
R81
20
11/
4W
R8105
390 1/4W
R8101
4.7K 1/4W
R81
04
6.8K
R81
08
8.2K
R81
03
470
1/4W
R81
02
56KC
8101
0.01
B
C81
06
0.00
1B
C81
05
0.1
B
Q8101KTC3875S_Y_RTK
21PIN CTL IN
B8103
MMZ1608R102CT
B8101
MMZ1608R102CT
NOTE : THE DC VOLTAGE EACH PART WASMEASURED WITH THE DIGITAL TESTERDURING PLAYBACK.
NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIMEOF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
P.CON+D5V
AT+3.3V
P.CON+12V
P-H/I-L_RGB-H
ASP/FS
AMP_A_OUT_R
AMP_A_OUT_L
G/Y_VIDEO
B/U_VIDEO
R/V_VIDEO
CVBS/C_VIDEO
A_GND
FROM POWER
11.412.1
12.111.4
0
0
POWER PCB ASSY (2/2)(A2K503A240)
1 2 3 4
C
D
F
A
B
E
67
5 6 7 8
CAUTION: DIGITAL TRANSISTOR
Q8105
KRA102SRTK
DVD_RGB_H_OUT
J8101MRC-021V-07_A
21PIN CONNECTOR
1
10
11
12
13
14
15
16
17
18
19
220
213
4
5
6
7
8
9
OS8101RFT5CB1
OPTICAL
1
2
3
H E
J8102 RCA-117-01COAXIAL
12
L8101
10uH 0405
CP8102E8223301
1
2
CAUTION: DIGITAL TRANSISTOR
R81
07
1.8K
R8114
220 +-1%
R8109
68 +-1%
R8110
68 +-1%
R8112
68 +-1%
R8113
75 +-1%
R8111
68 +-1%
R8115
220 +-1%
R8106
2.4K
R81
22
220
R8123
68 +-1%
R81
24
100K
R81
21
3.9K
TP8101
TP8102
C81
07
0.00
1B
C81
11
0.00
1B
C81
16
33P
CH
C8119
1 B
C81
03
100P
CH
C81
20
0.1
B
C8115
10006.3V YK_P
C8114
4706.3V YK_P
C8112
10006.3V YK_PC8113
4706.3V YK_P
C8118
10010V YK_P
C8104
150V KA_P
Q8103KTC3875S_Y_RTK
COAXIAL DRV
Q8104
KRC104SRTK
DVD_RGB_H_OUT
ASPDIF
COAXIAL
D_GND
21PIN_R
21PIN_L
21PIN_CTL
G/Y_VIDEO_OUT
B/U_VIDEO_OUT
R/V_VIDEO_OUT
BLANKING_OUT
CVBS_VIDEO_OUT
FROM AUDIO/JACK
(CP8001)
GND
VCC
INPUT
PCB240DPF015
NC
03.2
3.3
0
03.2
NC
NC
NC
NC
4.9
2.1
2.7
SPDIF
GND
7
8
5
6
1
2
3
4
* The parts except mark cannot be changed. On that occasion, replace whole Assy.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
01
1L-40
TKY 3.0A)
R66
13
DV-600AV-S68
1 2 3 4
10.11 USB PCB ASSY
CD6601
2H063401
CORD CONNECTOR
CD6602
E8241203
CORD CONNECTOR
CP6602A2001WR2-4P
1
2
3
4
D66
RB05
(SCHOT
W80
2
C66
04
0.1
B
C66
02
0.1
B
C66
03
1025
VKA
_P
C66
05
1025
VKA
_P
IC6601 RT9702-PBHIGH SIDE SW IC
12
3 45
B6601
HCB2012K-600T25
(60 OHM 2.5A)
CP660100_6232_006_102_800+
1
2
3
4
5
6
DURING PLAYBACK.MEASURED WITH THE DIGITAL TESTER
NOTE:THE DC VOLTAGE EACH PART WAS
USB_P_ON-H
USB_FLAG
USBP
USBN
GND
TO POWER PCB
GND
GND
P.CON+5V
P.CON+5V
GND
USBN
USB_POWER
USB_FLAG
GND
USBP
FROM/TO DVD PCB
EN
GND
/FLG VIN
VOUT
5.3
5.3
5.3
0
3.3
USB PCB ASSY (A2K401ADD0)
1 2 3 4
C
D
F
A
B
E
600T25
5A)
69
5 6 7 8
CP6603USB-A1D05F-4B4N
1
2
3
4
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
D6601
RB051L-40
(SCHOTTKY 3.0A)
R66
13
22K
W801
W810
W809
C66
07
10P
CH
C66
08
10P
CH
C6610
100P CH
C66
09
0.01
B
C66
06
476.
3VKA
_P
B6602
HCB2012K-600T25
(60 OHM 2.5A)
D66
08_1
UD
ZS3.
9B
D66
10_1
UD
ZS3.
9B
DEF133PCBDD0
+5V
GND
USB_DN
USB_DP
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S70
1 2 3 4
10.12 WAVE FORMS
MPEG/MICON/RF-AMP AUDIO/JACK
1
X4001 (XTAL0)V:200mV/div. H:500µs/div.
IC4002-pin146 (RCLK)V:1.0V/div. H:2nsec/div.
IC4002-pin215 (ASPDIF)V:1.0V/div. H:20nsec/div.
IC4002-pin231 (ACLK)V:1.0V/div. H:20ns/div.
CP4002-pin1 (FP_SCK)V:1.0V/div. H:20µsec/div.
2
3
4
5
6
7
8
9
10
11
DVD MT PCB ASSY
J8001-pin3 (Lch_Out)V:1.0V/div. H:500µsec/div.
12
13
14
15
J8001-pin2 (Rch_Out)V:1.0V/div. H:500µsec/div.
J8002-pin3 (SL)V:1.0V/div. H:500µsec/div.
J8002-pin2 (SR)V:1.0V/div. H:500µsec/div.
J8002-pin6 (CENTER)V:1.0V/div. H:500µsec/div.
J8002-pin5 (LFE)V:1.0V/div. H:500µsec/div.
J7302-pin6 (CVBS_Out)V:200mV/div. H:10µsec/div.
J7302-pin5 (Y_Out)V:500mV/div. H:10µsec/div.
J7302-pin2 (V_Out)V:500mV/div. H:20µsec/div.
J7302-pin3 (U_Out)V:500mV/div. H:20µsec/div.
VIDEO
Note : The encircled numbers denote measuring point in the schematic diagram.
1 2 3 4
C
D
F
A
B
E
71
5 6 7 8
DISPLAY
POWER PCB ASSY
DVD MT PCB ASSY OPERATION 1 PCB ASSYNote : The encircled numbers denote measuring point in the schematic diagram.
1
1
2
3
4
5
6
7
8
16
17
J8101-pin3 (AMP_A_Out_L))V:1.0V/div. H:200µsec/div.
J7304-pin3 (S_Y)V:500mV/div. H:20µsec/div.
J7304-pin4 (S_C)V:500mV/div. H:10µsec/div.
J8102-pin2 (COAXIAL)V:500mV/div. H:200ns/div.
OS8101-pin1 (OPTICAL)V:1.0V/div. H:200ns/div.
J8101-pin11 (G/Y_Video_Out)V:500mV/div. H:20µsec/div.
J8101-pin19 (CVBS_Video_Out)V:500mV/div. H:20µsec/div.
J8101-pin1 (21PIN_R_Out)V:1.0V/div. H:200µsec/div.
J8101-pin3 (21PIN_L_Out)V:1.0V/div. H:200µsec/div.
J8101-pin7 (B/U_Video_Out)V:500mV/div. H:20µsec/div.
J8101-pin15 (R/V_Video Out))V:500mV/div. H:20µsec/div.
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S72
1 2 3 4
11. PCB CONNECTION DIAGRAM
NOTE FOR PCB DIAGRAMS :1. Part numbers in PCB diagrams match those in the schematic diagrams.2. A comparison between the main parts of PCB and schematic diagrams is shown below.
3. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram.4. View point of PCB diagrams.Symbol In PCB
DiagramsSymbol In SchematicDiagrams
Part Name
B C E
D
D
G
G
S
S
B C E
B C E
D G S
B C E B C E
B C E
Transistor
Transistorwith resistor
Field effecttransistor
Resistor array
3-terminalregulator
CapacitorConnector
P.C.Board Chip Part
SIDE A
SIDE B
1 2 3 4
C
D
F
A
B
E
73
5 6 7 8
11.1 DVD MT PCB ASSY
DMF090A
C4075
R408
4
R800
7R8
008
R403
0
W87
9
W82
0
W81
4
W841
W842
C8038
W84
0
B401
0
R4007
W83
0 D400
3D4
002
R4059
R8043
W843
W86
1
L5904
L5903
L5902
L5901
W83
9
C4100
C4023
C412
6
C406
2
C4060_1
W889
C406
3
R231
6
R4056R4052
Q40
03
C802
5
C402
4
C4117
C7322
IC7302
W85
5
R4021
W837
W831
W851
IC4001
W850
C8031
C8028
C2301
R2304
C2306
R2313R2312R2325
W80
2
C230
7
R231
0C2
311
R2311
R2317
C230
5
W80
6W
805
C231
2 C2323C2322R2342R2331
R2329R2319
R233
8
R230
9
R230
8Q
2301
R230
7R2
306
Q2307Q2306
C2320
Q2304Q2302
C2321
Q2305
Q2303
IC2301
W83
3
R404
3
C410
3
C4119
C800
8
Q80
13
C800
7
R4038
C8015
Q8006
C8034
C8020
C802
3
C8064
C8037 C8014
C8019
C8026
C8073
C804
3
C806
3
Q8018
Q8016
R807
0
R807
9
R8078
R809
5
R8027
R8049
R806
7R8
073R8
071
R809
4 R8022
R802
9
IC8005
IC8004
J800
2
C8066
C8065
R803
3
C8047
C8072
C8032
Q80
02
R801
9
C8060
C8061
C8033C8048
R803
5
C8035 Q8004
Q80
05
Q8014
R802
6
R802
4
C8045
Q80
01
R800
5R8
009
C800
2IC8002
IC8007
IC80
01
J800
1
C8029
C8017
C8069
C8058 IC8008
Q80
24
R808
0
C8068
C8027
R8091
R808
8
R8090
R808
5 Q80
23 R8081
Q8012R8023 R8038
C8050
C8016
Q80
07
R802
0
Q80
03
IC8003
R801
8
C8041
C8036 C8013C8040R8041
R8001
D800
4
Q8011C8067
C7304
C7306
C7307
C730
8C7
309
C7312C7319
B730
2
W877
R7301
J730
4
B7305
CP7301
C7318
J730
2
C7315 C7314
B730
4
R730
2R730
3
C7316
CP8001
C7329
IC73
01
R731
9R732
0
C4011
R404
7R4
046
R402
7
R4025
R402
4
C404
7
C404
4
C4042
C403
1C4
032
R401
6R4
015
R401
7
R401
9
R401
8
W81
5
W81
2
C5924 R5901C5922R5921
C5923
IC59
02
C405
6B4
001
R401
3C4
096
IC4006
C409
4
C4095
CP4003
B400
2
C4099R4012R4011
C4093 C4112
C4098
W82
6
CP2301
C407
9
C407
8 C407
6
C407
7
R403
5
NR4001
C4114
W84
6 C4104
C409
1
CP40
02IC
4003
IC4004
CP23
02CP2303
CP4004
C412
3
C4050
R407
0
R407
1
R4083
R4082
C406
9
X4001
NR4002
IC4002
IC4005
C592
0
R5920
CP59
01 R5919
193
129 65
1
SIDE A SIDE A
DVD MT PCB ASSY
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S74
1 2 3 4
DMF090AR8
006
B8001
W878
C413
1
R8028
W86
2
W864
R805
9
B401
6Q4004
B401
8
C230
8
C592
5
R8065
B401
5
C590
1
W85
8
W85
7
B401
4
W807
C412
8
R400
9W
856
W819
W86
8
R404
0
R2327
R231
8
C230
2C2
303
R232
2
R232
0R2
323
R232
1
R4026
C401
2
C403
0
R4051
R405
0
W82
1
W822
W83
2
R4058
R402
8
R809
3R8
092
R807
2
Q8015
R807
4
C805
3R8
068
R804
5
C800
9
C805
9
R8050
R8053 C804
9
R803
6
C801
0
R807
6
R8069
Q8017
R807
7C8
056
R804
8
R803
1
R805
2
C804
4
R805
5R8
058
C805
7
C805
2R8
054
R801
1Q8020
R801
2
R804
6
C800
4
R8017
R800
3
D800
6
C803
9
R8025
R8002
D800
5
R802
1
D800
3
Q8008
Q8010
R809
6
C800
5
Q8021Q8019
R808
2
R808
7
R807
5
R8061
C804
6 C806
2
R8066
C805
5
R806
4R8
063
C805
1
R809
9
C800
6
C803
0
Q8009
C805
4
W80
4
R400
2
R406
1
R4064R4065
C407
4R4
066
C408
3R4
067
C730
5
R731
5
Q7302
C731
3
C730
2C7
317
B730
1
C733
0
R7317
R731
6
D730
7
D7310 R732
1R7
305D7
311
D730
8
D731
2D7
309
R7304
C406
7
C406
6
C411
0
R400
8R4
006
C406
5
C408
4
R404
8
Q4002
W82
8
R406
8R4
069
C406
1
R405
3R4
057C4
046
C404
8
C404
9
C404
3
C404
1
C403
5
C403
4R4
022
C403
3
C402
8C4
027
R402
0
W816
C402
6
C401
4C4
015
C401
6
C401
7
C401
3C4
019
C400
5
C400
7
C410
5
R400
5
C400
9C4
008
C402
0
C400
3
C400
2
C400
1
R4003
C403
8
C403
7W
813
C403
6 R403
9
C402
9
C408
6
R405
4C4
021
R4044
C402
5
C404
0
C402
2
R400
4
R401
4
C405
1C4
055
R400
1C4
064
C405
2
C412
0
C410
1
C410
2
C405
4C4
073
C407
2
C406
8
C408
8
C592
1
W82
7
C408
2
C408
1
C408
0C4
071
R406
0
SIDE B SIDE B
DVD MT PCB ASSY
1 2 3 4
C
D
F
A
B
E
75
5 6 7 8
11.2 OPERATION 1 PCB and OPERATION 2 PCB ASSYS
DEF129ADEF130A
DEF126A
DEF1
29A
DEF1
30A
DEF
126A
12
1
34
23
C611_1
C610_1
C604
C605
C651
C676
C658
C675
R662
R658R657
R656R655
R654
R653R652
R651
IC651
W809
W80
5
W80
7
W80
8SW
668
R666
W00
2
SW66
7
R664
D660 CP
605
OS6
51
D665
D658
D657
D656
D655
W00
6W
017
W01
8W
016
W01
5
W013
W011
D659
D652
D654
W010
W012
CP60
4
SW664
SW662
SW660
SW665
SW663
D651
W009
W007
W00
4
W003
CP60
1
C674
W00
1
C653
D669
V651
SW666
SW661 SW658
SW659
SW652
SW65
3
SW65
7
SW65
4
SW655
SW656
SIDE A SIDE A
OPERATION 1 PCB ASSY
OPERATION 1 PCB ASSY
(INSERTED PARTS) (CHIPMOUNTED PARTS)
OPERATION 2 PCB ASSY
OPERATION 2 PCB ASSY
OPERATION 3 PCB ASSY
OPERATION 3 PCB ASSY
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S76
1 2 3 4
11.3 POWER PCB ASSY
DPF015A
POWER
.
MARKED
AS
REPLACE
-
FIRE
OF
RISK
W825
W817
W039
D512_1
PH503
W819
IC505
D510
L8101
B502
C530C8104
W024
C504
CP504
Q515
Q502
D527
R512_1
R503
W011
W038
W022
W025
R8101
R8120
W021
W010
W007
W008
W002
W004
W001
W036
CP502
W037
C526
CP8102
C528D536
C527
W028
C521
C514
D535
C515_1
C522
W029W026
C8118
W027
OS8101
J8102
R8105
R8103
D517
R524
C516
R510_1
C513
C518
R546
D534
W814
C523
W015
D525
C520
R539
D515
IC503
D533
C506
C505
Q510
D519
D513
D511
W013
R502
W019W018
C535
R527
R505C531
T501
W030
W031
W032
CP503
D531
W016
R528R529
W005
C536
L503
L505
C538
Q504
R534
R530
W006
D523
C519
R517
D521
D528
D516D520
D522
R511
W003
R514
R513
C517
IC501
IC504
R507
D508
C509
IC502
C511
L501
C8112
W035
C8114
C8113
C8115J8101
D509B501D505
D502
D506
D503
F501FH501
FH502
C502_1
J501
SIDE A SIDE A
POWER PCB ASSY (INSERTED PARTS)
L
N
1 2 3 4
C
D
F
A
B
E
77
5 6 7 8
DPF015A
C540
R535R550 R533R542
R540
R548
R525
B8103B8101
R547
R8124
C8103R8123R8122
C8120
Q8103
R8121
R8107R8106
C8119
Q8101
Q8102
D8101
R8102R8108
R519
C8106
D8107R526
R545
C8101
R8109
R8115
R8114
C501
C541
D8105
D8103D8104
D8102
D8106
Q8105Q8104
R8104
C8105
R531
R536R537
R544Q513
Q505
R509
R543
R541
Q509
Q511
Q503
Q512
R506R538
Q506
R523 Q501
R516
R518
C503
R515
R504
C508
R8110
C8116
C8111C8107
R8113
R8112
R8111
SIDE A SIDE A
POWER PCB ASSY (CHIPMOUNTED PARTS)
DV-600AV-S5 6 7 8
C
D
F
A
B
E
DV-600AV-S78
1 2 3 4
11.4 USB PCB, LOADING MOTOR and SW ASSYS
DED021A
DED021A
M2601M2602
CD
2301
SW
2
GRYE
WH
BRDED020A
SIDE A SIDE A
DEF133A
DEF133A
BR
WH
51
SW SOLDER SIDE
LOADING MOTOR (CHIP MOUNTED PARTS) SOLDER SIDE
LOADING MOTOR (INSERTED PARTS) SOLDER SIDE
M2603CD2302
SW1
SOLDER SIDEUSB (CHIP MOUNTED PARTS)
SOLDER SIDEUSB (INSERTED PARTS)
CP6602
CP6603
C6605
C6603
C6606
CP6601
W802
W801 C6610
C6609
IC6601
W809
W810
D6610_1D6608_1
C6608
C6607
C6602
C6604
B6601
D6601
R6613
B6602
1 2 3 4
C
D
F
A
B
E
79
5 6 7 8
12. PCB PARTS LIST Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.The mark found on some component parts indicates the importance of the safety factor of the part.Therefore, when replacing, be sure to use parts of identical designation.When ordering resistors, first convert resistance values into code form as shown in the following examples.Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%).
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5 6 14 7 3
R 5 01 R 0
5 6 2 1
NOTES:
560 Ω47k Ω0.5 Ω1 Ω
RD1/4PU JRD1/4PU JRN2H KRS1P K
56 x 10 1
47 x 10 3
R501R0
561473
5.62k Ω RN1/4PC F562 x 10 1 5621
Mark No. Description Part No.LIST OF ASSEMBLIES 1..DVD MT PCB ASSY A2K501A130 1..OPERATION 1 PCB ASSY A2K501A270 (WYXZT5, WVXZT5 types) (*) 1..OPERATION 1 PCB ASSY A2K504A270 (YXZTUR5 types) (*) 1..OPERATION 2 PCB ASSY A2K401A280 1..OPERATION 3 PCB ASSY A2K401ADF0 > 1..POWER PCB ASSSY A2K503A240 1..USB PCB ASSY A2K401ADD0 1..DVD MECHA ASSY A2K001A650
(*) A2K501A270 and A2K504A270 have same service parts. But they are NOT COMPATIBLE.
Mark No. Description Part No.
DVD MT PCB ASSYSEMICONDUCTORS
IC2301 IC AM5766 I1UFV5766SIC4001 IC S-24CS08AFJ-TB-1GE I5HJ0S08A0IC4002 IC MT1389EXE/S-L IC8K0389SXIC4003 IC R3112N291A-TR-FA IE1F0291A0IC4004 IC ES29LV160EB-70TG S2K501AF01
IC4005 IC HY57V641620ETP-6 ICLJ0TP6C0IC4006 IC LM1117S-ADJ I1TF911170IC5902 IC PQ1K503M2ZPH I0GF9K5030IC7301 IC LA73054-TLM I03FG30540IC7302 IC SN74CBT3257PWR I5CJ032570
IC8001 IC TC7SHU04FU I55F004FU0IC8003 - IC8005 IC PCM1742KE/2K I17F042KE0IC8002, IC8007, IC8008 IC RC4580IDR I04J045800
OTHERSJ7302 RCA JACK 060R451010J7304 JACK DIN-409A 063R700013J8001 RCA JACK 060R451009J8002 RCA JACK 060R451011CP5901 CONNECTOR PCB SIDE 0694YJ3018
X4001 CRYSTAL (27MHz) 100GT02720
OPERATION 1 PCB ASSYSEMICONDUCTORS
IC651 IC PT6315 IF4K063150
SWITCHESSW652 - SW666 SWITCH TACT 0504R01T38
OTHERSV651 TUBE FLUORESCENT 096F82R601OS651 REMOTE RECEIVER 077A040002
OPERATION 2 PCB ASSYSWITCHES
SW667 SWITCH TACT 0504R01T38
OPERATION 3 PCB ASSYSWITCHES
SW668 SWITCH TACT 0504R01T38
POWER PCB ASSYRESISTORS
> R511 R,FUSE 68 OHM 1/4W R65584680J
OTHERSJ8101 SOCKET, 21PIN 063D100050J8102 RCA JACK RCA-117-01 060R401122CP8102 CORD CONNECTOR 06E8223301OS8101 OPTICAL DEVICE RFT5CB1 07AA000011
USB PCB ASSYSEMICONDUCTORS
IC6601 RT9702-PB I4UF097020
OTHERSCP6603 CONNECTOR PCB SIDE 06G5AA1001
Mark No. Description Part No.
DV-600AV-S5 6 7 8