1

DXL360/S Digital Protractor User Guide Features: 1) DXL360S: High accuracy ± (0.08° + 1%), high resolution 0.01° DXL360: ± (0.15° + 1%), resolution 0.02° 2) Laser Alignment 3) Dual and Single axis with user friendly LCD display angle 4) Rechargeable 5) V Shape metal case for easy to fit at the corner or pipe. 6) Magnetic base 7) Audible alarming at settable angle range

2

Specifications Accuracy: DXL360S: ± (0.08° + 1%) DXL360: ± (0.15° + 1%) Measuring range: Single axis: 360°, Dual axis: ±40° Resolution: DXL360S: 0.01° DXL360: 0.02° Response time: <0.4 second Audio sound: 60dB @ 30cm Operating temperature: 0 to 50°C Storage temperature: -10 to 60°C User Interface: Mono-color LCD with backlight Supply Power: Rechargeable Li-Ion Battery, 3.7Volt. Charger port: 5V 500mA Mini type-B USB port Power Consumption: Standby: 200uA, Operation: 20mA. Standby Battery Life: 2000 hours Operating Battery Life: 40 hours Dimensions (in mm): 66(L) x 64(W) x 29(H) Magnetic Base: affix at the bottom and back.

3

Button Functions

Function Descriptions ButtonNormal Mode Set Mode

ON/OFF

In normal operation, this button turns the device ON/OFF. Press and hold for 3 seconds to enable or disable backlight

Serves as the upward key for option selection.

HOLD When pressed, the current value will be freezed, the unit icon will be flash to indicate the reading is on hold. Press and hold for 3 seconds to enable or disable sound.

The icon on LCD will be

Serves as the downward key for option selection.

4

displaced accordingly. The buzzer beep could be set at different accuracy level. Refer to section “Angle Alarming”.

ZERO When pressed, the current reading is set to zero; subsequent measurements are relative to this reading. The LCD will show the icon to indicate the device is in zero mode. Press and hold for 3 seconds to enter Set mode, for set mode options.

Serves as the Set key.

5

LCD Icons Representations

Battery status indication icons These icons indicate the battery level. There are 3 levels representing empty, half and full. When the

In dual-axis mode, the LCD displays the direction of tilt graphically. The unit of scale is displayed below the graph with different scales. The scale is adjusted automatically depending on the measured angle. These icons show the available scales.

Degree mode. Flash when unit is HOLD mode

Sound notification on. Blank as off

6

Show this logo as relative value is showing. When the Zero button is pressed, the unit reset current angle to zero.

Direction of tilt icons, show the tilt angle direction with respect to the unit bottom right hand corner.

Dual-Axis Mode. Both the X and Y axis angle will be showed. Dual axis mode measures inclination upto +-40 degree for each axis before it automatically switch to single axis mode.

7

Single Axis Mode. Measure slope upto +-90 degree. The triangle icon indicates the direction of tilt with respect to the bottom right corner of the unit.

Battery Charging It has a built in Lithium Ion rechargeable battery. A standard charger is supplied that the input voltage is 110V to 240V AC, 50/60Hz, and the output is 5V DC, 500mA. The charger operating procedure is list below: 1) Plug the Charger into AC socket, the RED on the charger should

turned ON, 2) Plug the USB charging cable to the Charger, 3) Insert the other end of the USB cable to the unit,

8

4) The battery icon on the LCD blinks to indicate charging in process. Upon charging complete, the icon stops blinking.

5) The charging time is approx. 3 hours. The unit could also be charged by connecting the USB cable to the unit and a computer’s USB port. This has the same effect when charging the unit with the provided adaptor. Note: When the unit is turned OFF, and plug in the USB charge cable, the LCD will no show anything, it is NORMAL. Once the unit is turned ON, the battery icon should flash indicating the unit is in charging mode.

Relative/ Absolute Measurement Relative Measurement LCD Icon: Absolute Measurement LCD Icon: Blank

9

Relative and Absolute Mode Switching: 1 Press and release the “ZERO” key to set the relative

measurement zero point 2 Press and release the “ZERO” key to cancel the relative zero

point and back to absolute measurement mode.

Hold Function Holding Mode: LCD Icon blinking: Holding function:

1. Press and release the “HOLD” key to activate holding function, digit will freeze.

2. Press and release the “HOLD” key to cancel the holding function.

Auto Power Off For no movement in 30 minutes, the unit will power off.

10

Or we can set to never sleep mode at below instruction. Power auto off setting:

1. Press and hold “ZERO” key and enter MENU mode 2. Select “POWER” by “ON/OFF” and “HOLD” key, press “ZERO” key to enter Power mode 3. Scroll “NEVER” or “30MIN” by “ON/OFF” and “HOLD” key 4. Press “ZERO” key to confirm NEVER or 30MIN (30 minutes) sleep

Restore Factory Setting When you find that the unit is abnormal, you can restore the unit to factory setting. All calibration setting will be restored to factory setting. *Not suggest restore to factory setting in normal status, if for accuracy drift, please follow Calibration. After factory set, please redo calibration to ensure the accuracy. Restore to factory setting:

1. Press and hold “ZERO” key and enter MENU mode

11

2. Select “FACTORY SET” by “ON/OFF” and “HOLD” key, press “ZERO” key to enter FACTORY SET mode 3. Scroll “YES” or “NO” by “ON/OFF” and “HOLD” key 4. Press “ZERO” key to confirm

Angle Alarming Alarming Mode: LCD Icon: Alarming Angle setting:

1. Press and hold “ZERO” key and enter MENU mode 2. Select “BUZZER” by “ON/OFF” and “HOLD” key, press “ZERO” key to enter BUZZER setting Press and hold “ON/OFF” and “HOLD” key for fast scrolling the digit. 3. Press “ZERO” to enter setting value

BUZZER >SINGLE : 0 0 . 0 0 DUAL. X: 0 0 . 0 0

DUAL. Y: 0 0 . 0 0 RANGE : 0 0 . 5 0

12

SINGLE Vertical / Single axis mode alarming angle (Degree) DUAL.X Horizontal/ Dual axis mode X axis alarming angle

(Degree) DUAL.Y Horizontal/ Dual axis mode Y axis alarming angle

(Degree) RANGE The range (Degree)that will trigger the audible alarming

For example: SINGLE. set to 20.00 RANGE set to 01.00 While the unit is in +19◌ْ to +21◌ْ or -19ْ to -21◌ْ, the unit will alarm

13

Calibration Calibrate the unit, once you found that there is accuracy drift on the unit. You can verify the accuracy at below step:

At Step1, you measured X and Y value, X1 and Y1 At Step2, you measured X2 and Y2, in theory X1=-X2, Y1=-Y2. If the error is too large, you can enter calibration mode to eliminate the error

A

Step 1 Step 2

A

14

Accuracy drift is causing by large ambient temperature change (5 to 10 Degree Celsius) or the unit has been dropped. Calibration Procedure: Step 1: Press and hold the “ZERO” key enter Menu mode. Select “Calibration” mode, press “ZERO”. Place the unit on a flat table (no need perfect level table) LCD display “CALIBRATE DUAL AXIS PRESS SET”, press set and buzzer will beep; wait until the beep sound stop. While the buzzer is beeping keep the unit stable Step 2: Then rotate the unit 180 degree with the other side against the same place. Press the Set button again, and wait for the beep finished.

15

Step 3: LCD display “CALIBRATE HORIZONTAL PRESS SET”. Place the unit horizontal like the picture “STEP 3” and then press Set, wait until the beep sound stop. Step 4: Then rotate the unit 180 degree at the same place. Press the “ZERO” button again, and wait for the beep finished.

A

Step 1 Step 2

A

16

A

Step 5: LCD display “CALIBRATE VERTICAL PRESS SET”, mention that the LCD in upper side, hold on a flat wall. And then press “ZERO” Key. Wait for the “Beep” sound stop. Step 6: Then rotate the unit 180 degree with the other side against the at the same place of wall (LCD in upper side). Press the Set button again, and wait for the beep finished. Now, the LCD should go back to the

Step 3 Step 4

A

17

selection menu. The calibration is done, by selecting “Back” to go back for normal operation

A Step 5 Step 6

Wall Wall

A

18

PC Communication It has a PC data logging function. You can not directly plug the USB cable between PC to protractor by a general USB cable. You need to optional purchase the PC adapter You can continue to data logging X and Y inclination data to PC. Sampling time is around 2 Hz. Specification:

1) RS232 Com Port 9600 baud rate 2) USB connection ( include a RS232 to USB adapter)

Detail can visit our website or contact our sales person.

19

数字水平倾角仪 DXL360/S 使用说明书 特点： 1) DXL360S: 高准确度 ± (0.08° + 1%) , 高分辨率 0.01° DXL360: 准确度 ± (0.15° + 1%) , 高分辨率 0.02° 2) 单，双轴角度，LCD 显示 3) 充电功能 4) V 型金属外壳，方便适合在管道或角落里工作. 5) 磁性座 6) 可设置声音报警角度范围

20

规格： 精度: DXL360S: ± (0.08° + 1%) DXL360: ± (0.15° + 1%) 测量范围: 单轴: 360°, 双轴: ±40° 分辨率: DXL360S: 0.01° DXL360: 0.02° 回应时间: <0.4 second 蜂鸣声响: 60dB @ 30cm 工作温度: 0 to 50°C 存储温度: -10 to 60°C 用户界面: 单色背光液晶显示器 供电电源: 可充电锂离子电池，3.7V. 充电器界面: 5V 的 500mA 的迷你 B 型 USB 介面 功耗: 待机: 200uA, 操作: 20mA. 使用电池寿命: 2000 小时 工作电池寿命: 40 小时 尺寸 (毫米): 66(长) x 64(宽) x 29(高) 磁性座: 在底部和背部

21

按键功能

功能说明 按键

普通模式 设置模式 ON/OF

F 在正常操作下，此按键是控制主机开/关 按住 3 秒，控制背光开/关

在设置功能，

此按键可退回

功能表 HOLD 当按下时，该图标 将会闪烁，

表示数值被冻结起来. 按下并保持 3 秒，切换报警声开或

关。相应的 LCD 屏上显示的 图

标也会移走。 蜂鸣器提示音可以设置

不同的准确程度。请参阅节“角度报

警”

作为选择向下

的按钮

ZERO 当按下时，电流读数设置为零;随后的 作为设置键

22

LCD 显示说明

这些图示显示电池容量的水准。有

3 个层次，代表空，半满和充足。

当显示空, 表明要充电才能正常使

用

在双轴模式下，会有线指示倾角方

向和深度。该表是当时一个小格的

测量单位。

测量是相对于这个读数的。LCD 将显

示该图标，表示该设备是在相对测量

模式。 按住 3 秒进入设置模式，设置模式的

选择。

23

角度模式。当仪器在保持状态会闪

烁

声音报警已开，空白表示声音关闭

相对值标志显示。当按下“Zero”按钮，本机的重定现有角度为零。

倾斜方向，显示仪器底部倾斜角方

像

双轴模式。显示 X 和 Y 轴的角

度。超过双轴倾角+/ -40 度会自动

切换到单轴模式。 右方有指示线显示倾角方向。

24

单轴模式。测量斜坡 4X 90 °。下

方三角图示指倾斜方向。

电池充电 倾角仪内置一个充电锂电池. 配有一个标准充电器，输入电压为 110V-240V AC 50/60Hz 输出为 5V 直流,500mA 该从电器操作如下： 1）充电器插入交流插座上， 2）插入 USB 充电线连接至充电器， 3）将 USB 电缆的另一端插入倾角仪，

25

4）电池图示在 LCD 上闪烁，以指示电池充电过程。当充电完成后，该图

示停止闪烁。 5）充电时间是约 3 个小时。 该仪器也可以连接电脑 USB 接口，这具有相同的充电效果。 注：当本机被关闭，并在 USB 充电插头线，液晶将没有任何显示，这是正

常的，充电也是在自动运行。一旦仪器被打开，电池图示闪烁，显示在充

电中。

26

相对和绝对测量模式 相对测量模式 LCD 显示: 绝对测量模式 LCD 显示: 空白 相对模式和绝对模式切换 1 按下并释放“Zero”键设置相对测量零点 2 按下并释放“Zero”键取消相对零点，回到绝对测量模式。 数据保持 数据保持状态: LCD 图标闪烁: 数据保持

27

在测量的过程中，如需要读数保持，可按下“HOLD”键，显示器的显示

值将被锁住。再按动“HOLD”键，可解除读数保持状态

自动关机 若在开机后的任何一个 30 分钟内无任何操作，仪表会自动关机。 或者我们可以按以下操作设置无休眠模式 电源自动关机设置:

1. 按住“ZERO”键，进入菜单模式 2.按“ON/OFF”键，选择“POWER”，然后按”HOLD”键。

按”ZEARO”键进入”POWER”模式 3.按”ON/OFF”键和“HOLD”键会滚动 “NEVER” 或者 “30MIN” 4. 按”ZERO”键确认 NEVER(从不)或 30MIN（30 分钟休眠）

回复出厂设置 当您发现该机不正常，你可以恢复到出厂设置。所有的校准设置将恢复到

出厂设置。

28

*在正常状态下，不建议恢复到出厂设置，如果准确性漂移，请重做校准，

以确保准确性。 还原到出厂设置：

1. 按住“ZERO”键，进入功能表模式 2. 用“ON/OFF”键选择“Factory Set”，按“ZERO”键进入出厂设置模式 3. 用“ON/OFF”和”HOLD”键选择“YES”或”ON” 4. 按“ZERO”键确定

角度报警 角度报警模式: LCD 显示: 报警角度设置:

1. 按住“ZERO”键，进入功能表模式 2. 用“ON/OFF”和”HOLD”键选择

“BUZZER” 按零键进入报警角度设置。按

“ON/OFF”和”HOLD”键可快速滚动数字

BUZZER >SINGLE : 0 0 . 0 0 DUAL. X: 0 0 . 0 0

DUAL. Y: 0 0 . 0 0 RANGE : 0 0 . 5 0

29

3. 按“ZERO”确定设置值

SINGLE 单轴角度报警模式（度） DUAL.X 双轴角度报警模式 X 轴角（度） DUAL.Y 双轴角度报警模式 Y 轴角（度） RANGE 触发报警发声范围（度），

例如：单轴角度设定为 20.00 量程范围设置为 01.00 当水准角度是+19 ْ 到+21ْ 或-19ْ 到-21ْ，机子将报警

30

校准 一旦发现仪器精度有偏移，可以对机器进行校准。你可以按一下步骤验证

机子的准确性：

第一步, 你测量 X 和 Y 轴值，定义为 X1 和 Y1 第二步, 在同一地方，旋转机器 180 度，测量 X 和 Y 值，定义为 X2 和 Y2. 理论上，X1=-X2 Y1=-Y2 如果误差太大，你可以进入校准模式。消除误差 环境温度变化大（5 至 10 摄氏度）或机子受震荡会导致准确度漂移。

A

Step 1 Step 2

A

31

校准步骤: 第 1 步：按住“ZERO”键进入菜单模式。选择“Calibration”模式，按

“ZERO”。放置机子在桌子上。（不需要完美的水平桌子） LCD 显示“CALIBRATE DUAL AXIS PRESS SET”，按 SET 等待蜂鸣

器声音停止，在此期间，机子要保持稳定。 第 2 步：然后旋转机子 180 度对在同一地方。再次按下"SET"按钮，并等

待提示音结束。

A

A

Step 1 Step 2

32

第 3 步：LCD 显示“CALIBRATE HORIZONTAL PRESS SET”。水平放

置机器，如图片“第三步”，然后按”SET"，直到提示音停止等待。 第 4 步：然后旋转机器 180 度在同一位置。按“ZERO”按钮，并等待提

示音结束。

Step 3 Step 4

A A

33

第五步：液晶显示“CALIBRATE VERTICAL PRESS SET”，把机器贴

在墙上，LCD 显示器必须在上方。然后按“ZERO”的键。等待“滴”的

声音停止。 步骤 6：然后旋转机子 180 度对在同一个地方的墙壁（液晶显示器在上

方）。再次按下“SET"按钮，并等待提示音结束。现在，液晶显示器应该

回到选择菜单。校准完成，按“Back”返回正常运作

34

PC 通讯 仪器拥有个人电脑的资料记录功能。 你不能从个人电脑直接插入一般的 USB 电缆到机器。 你需要选择购买转接器（型号： RS232）

A Step 5 Step 6

Wall Wall

A

35

您可以由机器采集资料记录到个人电脑。 采样时间约为 2 赫兹。

产品规格： 1）RS232 Com 埠 9600 串列传输速率 2）USB 介面（RS232 串口包括 RS232 转 USB 适配器) 详情可流览我们的网站或联系我们的销售人员。