Dynajet UHP 170 - viskor.com · 2 3 MM 3474/08 GB MM 3474/08 GB Dynajet ® UHP 170 Maximum power...

MM 3474/08 GB

Dynajet ® UHP 170Professional cold water ultrahigh-pressure units

2 3

➀ ➁ ➂

MM 3474/08 GB MM 3474/08 GB

Dynajet ® UHP 170Maximum power – the 170 Horse Power class of Dynajet ® ultrahigh-pressure units

Professional cold water ultrahigh-pressure units

This UHP units represents the high end class for mobile Dynajet ® high-pressure units, delivering pressures up to 2,800 bar (40,600 PSI). They are ultrahigh-performance machines that are intended for the most difficult and demanding jobs. They are economical, easy to operate and offer high levels of safety.

They are ideally suited to building redevelopment, paint stripping, rust removal, surface removal or even, for instance, heat exchanger cleaning. Even the mostdifficult deposits and coatings are quickly removed.

Robust, durable Deutz four-cylinder diesel engine, three-plunger high-pressure pump with carbide plungers, drive-train cooling system, water temperature-monitoring system, storage tank with booster pump inc. filter and booster-pressure monitoring system, protection/ leakage tray, total control with pressure-value presetting, option to choose manual engine speed control or dump gunuse, simple to control via the display, dual-hood targa principle (depending onthe type), chassis and noise insulation cover.

Variants

Three versions of the units in the 170 HP class are available:➀ Stationary without hood, weight approx. 1,900 kg ➁ Stationary with hood, weight approx. 2,000 kg➂ Mobile trailer with hood, weight approx. 2,100 kg

The picture shows the Dynajet ® UHP 170 as a mobile trailer with noise insulating cover

Standard scope of supply

www.dynajet-online.com

Spark arrestor for diesel engine, is mounted on the outside on the machine chassis, retrofitting is possible

Part no. 501 396

Additional emergency shutdown, on cable drum with 50 m cable and plug Part no. 458 018

Height-adjustable towing gear with truck/ trailer coupling ring On request

Special equipment

Standard scope without accessories. Suitable accessories and accessories packages can be found on pages 74 to 83.

Type cold water ultrahigh-pressure unit

Max. flow rate 18.5-40.5 l/ min (4.89-10.71 USgal/ min) 10.5-23.5 l/ min (2.78-6.22 USgal/ min) 8.3-18 l/ min (2.20-4.76 USgal/ min)

Max. operating pressure 1,200 bar (17,400 PSI) 2,000 bar (29,000 PSI) 2,800 bar (40,600 PSI)

Pump low-speed high-pressure pump with three carbide plungers, integrated reduction gear and oil cooler

Engine (oil-cooled) Deutz 4-cylinder diesel (TCD 2013L04 2V) with 170 HP at 2,400 rpm

Speed of engine/ pump 1,100-2,200 rpm/ 257-565 rpm

Water-tank capacity approx. 70 l (18.5 USgal) 70 l (18.5 USgal) 70 l (18.5 USgal)

Volume of fuel tank approx. 190 l (50.26 USgal) 190 l (50.26 USgal) 190 l (50.26 USgal)

L x W x H (stationary without hood)/ weight 250 x 140 x 185 cm/ 1,900 kg

L x W x H (stationary with hood)/ weight 255 x 140 x 185 cm/ 2,000 kg

L x W x H (mobile trailer with hood)/ weight 392 x 188 x 210 cm/ 2,100 kg

➀ Part no. (stationary without hood) 111 600.210 111 600.230 111 600.240

➁ Part no. (stationary with hood) 111 600.110 111 600.130 111 600.140

➂ Part no. (mobile with hood) 111 600.010 111 600.030 111 600.040

Technical data 1200 2000 2800

Professional cold water ultrahigh-pressure units

Simple control system and complete monitoring in a small space, with protective cover, protects against dirt and also acts as a sunshade.

The operating and service covers, which can be opened very wide, can be usedto easily reach all the important parts.


4 5MM 3474/08 GB MM 3474/08 GB

Professional high-pressure units www.dynajet-online.com

Quick pump head changes for adapting the machine todifferent pressure rates

Ultrahigh-pressure pump offering maximum efficiency, saves fuel

Low-speed ultrahigh-pressure pump with an integrated oil coolerthat prevents overheating and extends the operating life

Diaphragm operated pressure regulation, safty and unloader valve switched and controlled by compressed air for soft switching without pressure peaks, no danger of freeze

Hood locks robust and adjustable lock

Carbide plungers offering the highest durabilityfor a long service life

Easy operating-mode selection for selecting automatic pressure modus, manual use and compressed air toolsPump power end

made out of cast iron, solid and reliable

Powerful Deutz industrialdiesel enginemodern TIER 3 low-speed enginefor robust operation

Suction and high pressure connections accessible from the outside

Easy control system offering improved ease of operation through a large display with symbol and text indicators, complete with protective cover that also acts as a sunshade

Mobile ultra high-pressure units up to 2,800 bar (40,600 PSI) Highly modern, user-friendly

control system with large symbols and a text display for easy operation

Robust, modern, service-friendly machine concept with 2 hoods

Optimum, easy adaptation of the machine to the cleaning task (interchangable pump heads, operation of compressed-air tools)

An overview of our UHP cold water units

Professional high-pressure units www.dynajet-online.com

Dual-hood targa concept for operator end engine side, offering ideal access and protection

Noise insulation reduces noise level

Integrated compressed-air system for operating rotating high-pressure tools

Protection frame to protect the machine

Storage area under the hood for tools,hoses and accessories

Optimum air flow for engine and high-pressurepump cooling

Frame and chassis produced to Putzmeister quality, tested on a truck test track

Large fuel tank for long periods of use on-site

Closed bottom/ leak tray protects machine and environment against contamination

Water storage tank for test surfaces, buffer and separator from supply lines

You can find technical data for our hot-water trailers on page 38 and 39.

6 7

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

MM 3474/08 GB MM 3474/08 GB

Dynajet ® accessoriesDN: Diameter (mm) IT: Internal threadPN: Max. operating pressure (bar) ET: External thread

An overview of Dynajet ® nozzle shapes and types

Shape A – round-jet nozzle

With 1⁄4” NPT outside thread (cone-shaped thread), for use up to max. 500 bar (7,250 PSI), extremely hard spot jet for removal on small surfaces, can be screwed into any nozzle carrier, sealed with sealing paste or teflon tape

Shape B – flat-jet nozzle

With 1⁄4” NPT outside thread, for use up to max. 500 bar (7,250 PSI),available in various jet angles 5°, 25° or 40°, for quick surface removal,to be screwed directly into any nozzle carrier, identical sealing procedure as with shape A (sealing paste or teflon tape)

Shape C – round/ spot jet nozzle

Plug-in nozzle version, for use up to max. 1,600 bar (23,200 PSI), extremely hard spot jet for the most difficult deposits, water jet has a very high exit speed, effective energy transformation, held in the nozzle carrier via union nut, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307)


Pressure Thread Seal350 bar (5,075 PSI) M22 x 1.5 O-ring/ support ring500 bar (7,250 PSI) M22 x 1.5 (from middle of '08 = M24 x 1.5) O-ring/ support ring800-1,200 bar (11,600-17,400 PSI) M24 x 1.5 DKO Cone seal O-ring1,600-2,800 bar (23,200-40,600 PSI) 9⁄16” -18 UNF-LH Metallic sealing via cone

Technical information on threaded unions/ connections

Nozzles - a general overview

Shape F – turbo-type rotating nozzle

Universal multi-purpose jet nozzles for use up to max. 2,000 bar (29,000 PSI), combines the advantages of a large surface power and an extremely hard water jet, for maximum cleaning performance with very high surface power, variationin design depending on the pressure level, speed adjustment also available in types up to 350 bar (5,075 PSI), for adapting cleaning performance to the object in question, nozzle pin and ceramic seat can be replaced as a repairkit, threaded connection 1⁄4” IT up to 500 bar (7,250 PSI) or 9⁄16” - 18 UNF-LHfrom 800-2,000 bar (11,600-29,000 PSI)

Ultrahigh-pressure nozzle for continuous use with carbide inserts, high speed nozzle thanks to extremely high efficiency, for use up to max. 3,000 bar (43,500 PSI), screwed directly into nozzle carrier or rotating nozzle system, only available as a round-jet nozzle, with hexagon socket and M10 outside thread, metallic cone seal

Shape E – nozzle insert for small dimensions

Small sapphire round-jet nozzle with outside thread and quadruple edge (5 mm), for use up to max. 1,000 bar (14,500 PSI), extremely small dimensions, long operating life thanks to the use of sapphire, used in the WSS 1000 water-sand-blasting system, seal via sealing glue

Shape D – flat-jet nozzle

Plug-in nozzle version, for use up to max. 1,600 bar (23,200 PSI), available as 15° or 30° jet angle, high surface power with hard jet pressure, held in the nozzle carrier via union nut, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307)


Shape G – ultrahigh-pressure round-jet nozzle

8 9

21

MM 3474/08 GB MM 3474/08 GB

Part no. Lance for PN 3,000 bar (43,500 PSI) with electric contact via 491 871proximity switch, short cable and connector, pressure ringand pressure screws not included, safety trigger with

lock to prevent unintentional opening,connections 2x M26 x 1.5 IT

See page 68 for a technical explanation.

Threaded connection on both sides M24 x 1.5 DKO IT, cone nipple with O-ring,connector and nut made of rust-resistant steel, 4 reinforcement layers of spiralsteel wire, PN 1,200 bar (17,400 PSI), outer layer is made of polyamide Part no. Diameter 10 mm, length 10 m 477 156Diameter 10 mm, length 20 m 477 157

High-pressure hose lines

Part no.For connecting 2 high-pressure hose lines with connections 437 756for thread 2x M24 x 1.5 DKO ET, material: rust-resistant steel

Part no.Suitable for high-pressure cleaning gun, for absorbing recoil forces 489 323

Part no.For user-friendly operation, prevents twisting of the hose-lines, 494 275installed directly between the high-pressure cleaning gun and the high-pressure hose line, connections M26 x 1.5 ET (cleaning gun connection) and M24 x 1.5 DKO ET(hose connection), PN 1,600 bar (23,200 PSI), max. 95 °C

Part no.For spray lance SL 3000, inlet M24 x 1.5 DKO ET, 494 900to the hose, outlet to lance M26 x 1.5 ET

Part no.Between connection nipple (Part no. 494 900) and SL 3000 (Part no. 491 871) 037 535.001

Hose connection

Swivel joint

Connection nipple

Sealing ring

DN: Diameter (mm) IT: Internal threadPN: Max. operating pressure (bar) ET: External thread


Spray lance SL 3000

Shoulder support

Accessories up to 1,200 bar (17.400 PSI)Accessories up to 1,200 bar (17.400 PSI)

Extension spray wands

Direct fixation in the high-pressure cleaning lance, outside diameter 14.3 mm,

spanner flat 12 mm on both sides, threaded connection on both sides 9⁄16“-18 UNF-LH ET, PN 1,600 bar (23,200 PSI), internal diameter 8 mm Part no. Length 350 mm 482 505Length 800 mm 482 515 Length 1,200 mm 482 516 Length 2,000 mm 482 517

Dynajet ® recommendation:for safety reasons, you should always select a spray wand of 800 mm or longer, so that whencombined with the spray lance SL 3000, an overall length of approx. 800 mm is reached



Side-handgrip

Protective handle

Part no. For mounting on the high-pressure spray wand, 475 464adjustable in any position

Part no. For surrounding and protecting the high-pressure spray wand 489 336

Pressure ring and pressure screw

Part no.(Fig. 1) pressure ring for screwing on ultrahigh-pressure connections, 474 636slot version to prevent unintentional loosening of the connection through

vibrations, thread 9⁄16“-18 UNF-LH IT

(Fig. 2) pressure screw for screwing on ultrahigh-pressure connections, 474 635anti-vibration type when combined with pressure ring, thread M26 x 1.5 ET

Remote control cable

For accessories and tools with remote control via electrical contact

Part no. Length 25 m, loose, with coupling and connector 468 089 Length 50 m, loose, with coupling and connector 468 090 Length 25 m, on drum, with solid socket and plug 482 093Length 50 m, on drum, with solid socket and plug 482 094

10 11

8

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

7

1211

56

34

5 6

10

1

9

21

2

1

2

MM 3474/08 GB MM 3474/08 GB

Part no. For attaching 1x plug-in nozzle insert (shape C or D), consisting of 1x basic body, 488 299 1x union nut, PN 1,500 bar (21,750 PSI), connection 9⁄16“-18 UNF-LH IT, extremely light-weight, nozzle with sealing ring and support ring not included in scope of supply

Part no. (Fig. 1) sealing ring for plug-in nozzles (shape C and D) 484 295(Fig. 2) support ring for plug-in nozzles (shape C and D) 489 307

Accessories up to 1,200 bar (17.400 PSI)

Nozzle insert (shape C) = round-jet nozzle

Nozzle insert (shape D) = flat-jet nozzle

Rotation nozzle system RDS-Easy 1600-4

Round-jet nozzle as nozzle insert, material: stainless steel, vacuum-hardened, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307), PN 1,500 bar (21,750 PSI)

Separate data sheet with available diameters and nozzle tables on request.

Flat-jet nozzle as nozzle insert, material: stainless steel, vacuum-hardened, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307), PN 1,500 bar (21,750 PSI)

Separate data sheet with available diameters and nozzle tables on request.

Part no.Universal rotating nozzle system self-driven via reaction force, speed adjustment 489 723via contact-free magnetic brakes approx. 1,000-2,500 rpm, weights only approx. 1.0 kg, nozzle carrier head with 20° for attaching max. 4 shape G nozzle inserts (M10), connection 9⁄16“-18 UNF-LH IT, nozzle inserts not included in scope of supply

Separate data sheet with available diameters for shape G nozzle inserts on request.

Complete swivel joint 489 729Wear parts set for swivel joint 489 730Spare protection front cover 489 731


Nozzle carrier

Sealing ring and support ring for shape C and D nozzle inserts

Rotating "Turbo" type nozzle

Part no.Universal multi-purpose nozzles, self-driven with nozzle reaction force for extremely hard 438 683spot jet, the ideal combination of surface treatment and removal, for nearly all fields of application, PIN insert can be replaced, connection 9⁄16“-18 UNF-LH IT, rotor d= 1,25 (designed and calculated for 1,200 bar (17,400 PSI) at 32 l/ min (8.47 USgal/ min))

Accessories up to 1,200 bar (17.400 PSI) www.dynajet-online.com

Foot switch

Flexible lances

Part no.Complete with proximity switch for remote control 505 568 with short cable and connector. No valve inside!

Connection direct on a high pressure hose Part no.Connections M24 x 1.5 DKO IT, M7 ET for pipe-cleaning nozzles, outside diameter 12 mmInternal diameter 4 mm, length 6 m 482 370Internal diameter 4 mm, length 12 m 482 371Internal diameter 4 mm, length 25 m 482 372

Connections M24 x 1.5 DKO IT, G ¼“ ET for pipe-cleaning nozzles, outside diameter 15 mmInternal diameter 6 mm, length 6 m 482 865Internal diameter 6 mm, length 12 m 482 879Internal diameter 6 mm, length 25 m 482 880

Pipe and head exchanger cleaning nozzles

Nozzles on request(Fig. 1) rigid design, drilled as pulling nozzle (Fig. 2) rotating, drilled as pulling nozzle

Each set consists of: Fig.1x Spray lance SL3000 with hose connection M24x1.5 ET 11x Shoulder support 21x High-pressure extension wand 800 mm 31x Side handgrip 41x Pressure screw 51x Pressure ring 61x Nozzle carrier for shape G nozzle 71x Round-jet nozzle (shape G) 8 1x Remote control cable 25 m 9 1x High-pressure hose, 20 m, DN 10, PN 1,200 bar (17,400 PSI) 10 1x Antiseize paste for lubricating metallic threaded connections 1x Rotating nozzle system RDS-Easy 1600-4* 114x Round-jet nozzle (shape G) for RDS-Easy-1600-4* 12* included only in the package "1,200 bar (17,400 PSI) Power" (Part no. 498 007)

Dynajet ® high-pressure accessories set for 1,200 bar (17,400 PSI)

Part no.1,200 bar (17,400 PSI) Basic Set 498 0061,200 bar (17,400 PSI) Power Set 498 007

12 13

1

2

21

MM 3474/08 GB MM 3474/08 GB

Pressure ring and pressure screw

Snap hook

Safety cable

Hose connections

Thread protection caps

High-pressure hose lines

Part no.(Fig. 1) pressure ring for screwing on ultrahigh-pressure connections, 474 636slot version to prevent unintentional loosening of the

connection through vibrations, thread 9⁄16“-18 UNF-LH IT

(Fig. 2) pressure screw for screwing on ultrahigh-pressure connections, 474 635anti-vibration type when combined with pressure ring, thread M26 x 1.5 ET

Part no.For connecting and interlocking 2 high-pressure hose 060 563.008lines, simple snap them on to the eyes of the hose mantle

Part no.For securing the interlocking protection to the spray lance, comes complete with 1x snap hook 481 818

Part no.For connecting 2 ultrahigh-pressure hose lines with connections 474 637for thread 2x 9⁄16“-18 UNF-LH IT, equipment consists of: 1x housing, 2x pressure ring and 2x pressure screw

For M26 x 1.5 thread, e.g. UHP hoses, machines, cleaning guns and lances Part no.

(Fig. 1) external thread, M26 x 1.5 ET 505 565(Fig. 2) inside thread, M26 x 1.5 IT 505 566

Complete with PVC protection hose, security system on both sides as hose mantle with interlocking protection, threaded connection on both sides 9⁄16“-18 UNF-LH ET, PN 2,000 bar (29,000 PSI) or PN 2,800 bar (40,600 PSI) Part no.2,000 bar (29,000 PSI), 5 mm diameter, 5 m length (short "working hose" direct on the lance) 489 6282,000 bar (29,000 PSI), 5 mm diameter, 10 m length 489 6292,000 bar (29,000 PSI), 5 mm diameter, 20 m length 489 6302,000 bar (29,000 PSI), 8 mm diameter, 10 m length 477 1622,000 bar (29,000 PSI), 8 mm diameter, 20 m length 477 163

2,800 bar, 5 mm diameter, 5 m length (short "working hose" direct on the lance) 482 4032,800 bar, 5 mm diameter, 10 m length 477 1652,800 bar, 5 mm diameter, 20 m length 477 1662,800 bar, 8 mm diameter, 10 m length 496 7112,800 bar, 8 mm diameter, 20 m length 496 715



Accessories up to 2,800 bar (40,600 PSI)Accessories up to 2,800 bar (40,600 PSI)

Spray lance SL3000

Shoulder support

Remote control cable

Swivel joint

Part no.For user-friendly operation, prevents twisting of the hose lines, 494 276 installed directly between the high-pressure lance and the high-pressure hose line, connections M26 x 1.5 ET (lance connection)and M26 x 1.5 IT (hose connection), PN 2,800 bar (40,600 PSI)



Part no.Lance for PN 3,000 bar (43,500 PSI) with electric contact via 491 871proximity switch, short cable and connector, pressure ring and pressure screws not included, safety trigger with lock to prevent unintentional opening, connections 2x M26 x 1.5 IT

Part no.Suitable for spray lance for absorbing recoil forces 489 323

For accessories and tools with remote control via electrical contact Part no. Length 25 m, loose, with coupling and connector 468 089 Length 50 m, loose, with coupling and connector 468 090 Length 25 m, on drum, with solid socket and plug 482 093Length 50 m, on drum, with solid socket and plug 482 094

Extension spray wands

Direct fixation in the high pressure cleaning lance, outside diameter 14.3 mm, spanner flat 12 mm on both sides, threaded connection on both sides 9⁄16“-18 UNF-LH ET, PN 3,200 bar (46,400 PSI), internal diameter 5 mm Part no. Length 350 mm 482 518Length 800 mm 482 519 Length 1,200 mm 482 520 Length 2,000 mm 482 521

Dynajet ® recommendation:for safety reasons, you should always select a spray wand of 800 mm or longer, so that when combinedwith the spray lance SL 3000, an overall length of approx. 800 mm is reached

14 15

1213 1213

10 10

11 11

1514

56 56

8

9

3 7412

5 6

8

9

3 7412

5 6

MM 3474/08 GB MM 3474/08 GB

Accessories up to 2,800 bar (40,600 PSI)

Dynajet ® high-pressure accessories set as "Basic package"


Part no.2,000 bar (29,000 PSI) Basic Set 498 0042,800 bar (40,600 PSI) Basic Set 498 002

Equipment consists of: Fig.1x Spray lance SL3000 11x Shoulder support 2 1x High-pressure extension wand 800 mm 31x Side handgrip 42x Pressure screw 52x Pressure ring 61x Nozzle carrier for shape G nozzle 72x Round-jet nozzle (shape G) 8, 9 1x Remote control cable 25 m 10 1x High-pressure hose, 20 m, DN 8, PN 2,000 bar (29,000 PSI) with 11

hose protection and hose mantle up to 2,000 bar (29,000 PSI) or1x High-pressure hose, 20 m, DN 8, PN 2,800 bar (40,600 PSI) with protective hose and hose mantle up to 2,800 bar (40,600 PSI)1x Safety cable 12 4x Snap hooks 131x Antiseize paste for lubricating metallic threaded unions

Complete accessory package, suitable for Dynajet ® UHP 170 types,complete with a selection of suitable nozzle equipment (see page 68 for details).

Accessories up to 2,800 bar (40,600 PSI)

Dynajet ® high-pressure accessories set as "Power package"


Part no.2,000 bar (29,000 PSI) Power Set 498 0052,800 bar (40,600 PSI) Power Set 498 003

Equipment consists of: Fig.1x Spray lance SL3000 11x Shoulder support 21x High-pressure extension wand 800 mm 31x Side handgrip 42x Pressure screw 52x Pressure ring 61x Nozzle carrier for shape G nozzle 72x Round-jet nozzle (shape G) 8, 9 1x Remote control cable 25 m 10 1x High-pressure hose, 20 m, DN 8, PN 2,000 bar (29,000 PSI) with 11 hose protection and hose mantle up to 2,000 bar (29,000 PSI) or1x High-pressure hose, 20 m, DN 8, PN 2,800 bar (40,600 PSI) with

protective hose and hose mantle up to 2,800 bar (40,600 PSI)1x Safety cable 12 4x Snap hooks 131x Rotating nozzle system RDS-Easy 3000-4 144x Round-jet nozzle (shape G) for RDS-Easy 3000-4 151x Antiseize paste for lubricating metallic threaded unions

Complete accessory package, suitable for Dynajet ® UHP 170 types, equipment identicalto "Basic package", however in addition it comes with magnetically braked 4-jet nozzle systemEasy 3000-4 (see page 68 for details)

16 17MM 3474/08 GB MM 3474/08 GB

Accessories up to 2,800 bar (40,600 PSI) www.dynajet-online.com

Rotating nozzle system RDS-Easy 3000-4

Side-handgrip

Rotating "Turbo" type nozzle

Spare rotor

Part no.

Universal rotating nozzle system self-driven via reaction force, speed adjustment via 489 724contact-free magnetic brakes approx. 1,000 - 2,500 rpm, weights only approx. 1.0 kg, nozzle carrier head with 20° for attaching max. 4 shape G nozzle inserts (M10), connection 9⁄16“-18 UNF-LH IT, nozzle inserts not included in scope of supply

Separate data sheet with available diameters for shape G nozzle inserts on request.

Complete swivel joint 489 732Wear parts set for swivel joint 489 733Spare protection front cover 489 731

Part no.For mounting on the high-pressure spray wand, 475 464adjustable in any position

Part no.Universal multi-purpose nozzle only for max. 2,500 bar (36,250 PSI), 497 304self-driven via reaction force for an extremely hard spot jet, the ideal combinationof surface treatment and removal, for nearly all fields of application, PIN insert can be replaced, connection 9⁄16“-18 UNF-LH IT, rotor diameter 0.9 mm (designed and calculated for 2,000 bar (29,000 PSI), 23.5 l/ min(6,22 USgal/ min))

Part no.For max. 2,500 bar (36,250 PSI), diameter 0.90 mm, suitable for turbo nozzle (Part no. 497 304) 497 310

Accessories up to 2,800 bar (40,600 PSI)www.dynajet-online.com

Nozzle carrier

Nozzle insert (shape G)

Part no. For attaching 1 shape G nozzle insert, M10 internal thread, 482 783PN 2,800 bar (40,600 PSI), connection 9⁄16“-18 UNF-LH IT, extremely light-weight

Round-jet nozzle with outside thread M 10 and hexagon socket, screw material:stainless steel, nozzle insert with intake cone made of vacuum-hardened stainless steel,metallic seal made from bronze, use up to 3,000 bar (43,500 PSI)

Diameter in mm: Part no. 0.00 (blind nozzle) 455 4590.20 457 4530.25 454 9790.30 457 4540.35 455 4570.40 454 9820.45 457 4550.50 455 4580.55 457 4560.60 457 4570.65 457 4580.70 457 4590.75 457 4600.80 457 4610.85 492 7980.90 492 7990.95 492 8001.00 498 1791.05 498 1801.10 498 1811.15 498 1821.20 498 183

Other diameters can be obtained on request.



18 19MM 3474/08 GB MM 3474/08 GB

Sizing information for ordering protective clothing:

Order size S (Small) Body size 158 – 170 cm Chest circumference 80 – 92 cmOrder size M (Medium) Body size 170 – 182 cm Chest circumference 92 – 104 cmOrder size L (Large) Body size 182 – 188 cm Chest circumference 104 – 116 cmOrder size XL (X-Large) Body size 188 – 194 cm Chest circumference 116 – 124 cmOrder size XXL (XX-Large) Body size 194 – 200 cm Chest circumference 124 – 132 cm

Protective suit

Poratex Premium, 100% waterproof, 2-piece (jacket + overalls), without protective function against high pressure

Part no. Medium 414 067 Large 414 068 X-Large 414 069 XX-Large 414 070

Overalls

As protection against dirt, 100% waterproof, with cap and neck ruff, without protective function against high pressure

Part no. Large 426 895 X-Large 426 896

Personal safety equipment

"Speedy" protective goggles

Part no. Made from scratch-proof colourless polycarbonate sheet, 414 094 with length-adjustable wings


Overalls*

As protection against ultrahigh pressure, 100 % waterproof, different protction rates available

Part no. up to 500 bar (7,250 PSI) high-pressure cleaning:Medium (size S – M) 460 749 Large (size L – XL) 460 750 X-Large (size XXL) 460 751

up to 1,000 bar (14,500 PSI) high-pressure cleaning:Medium (size S – M) 460 752 Large (size L – XL) 460 753 X-Large (size XXL) 460 754

up to 2,000 bar (29,000 PSI) high-pressure cleaning:Medium (size S – M) 460 747 Large (size L – XL) 460 300 X-Large (size XXL) 460 748

Clothing for protection against ultrahigh-pressure

Safety vest*

For protection against ultrahigh pressure, 100% waterproof,in different types for different protection-pressure ranges

Part no. up to 500 bar (7,250 PSI) high-pressure cleaningversion A (size M-XXXL) 460 755 up to 1,000 (14,500 PSI) bar high-pressure cleaningversion A (size M-XXXL) 460 756 up to 2,000 bar (29,000 PSI) high-pressure cleaningversion A (size M-XXXL) 460 302

Personal safety equipmentwww.dynajet-online.com

Part no. Up to 2,000 bar (29,000 PSI), 476 881 easy to put on and take off,weight 1.7 kg

High-pressure apron*

* The protective clothing is certified in accordance with Regulation 89/ 686/ EEC and BGR 191

20 21MM 3474/08 GB MM 3474/08 GB

Gloves Lined, 100 % waterproof, breathable, heat-resistant, without protection function for high-pressure

Part no. Size 8 414 086 Size 9 414 087 Size 10 414 088 Size 11 414 089

Safety shoe covers*

With clips for securely fastening them over your regular safety boots, for protection against ultrahigh pressure, very comfortable and light to wear, one size fits all Part no. Version designed for 1,000 bar (14,500 PSI) 460 757 Version designed for 2,000 bar (29,000 PSI) 460 306

Hand protection*

For ultrahigh-pressure protection, especially for right or left hand, one size fits all Part no. Hand protection – left hand:Version designed for 500 bar (7,250 PSI) 460 758 Version designed for 1,000 bar (14,500 PSI) 460 759 Version designed for 2,000 bar (29,000 PSI) 460 760

Hand protection – right hand:Version designed for 500 bar (7,250 PSI) 460 761 Version designed for 1,000 bar (14,500 PSI) 460 762 Version designed for 2,000 bar (29,000 PSI) 460 307

Hose protection*

Part no. For protection of the hose, 460 310 diameter of 60 mm, length of approx. 700 mm

Personal safety equipment

Boots without protection

Types conform with CE, S5 EN 345 Part no. Size 42 414 076 Size 43 414 077 Size 44 414 078 Size 45 414 079 Size 46 414 080


* The protective clothing is certified in accordance with Regulation 89/ 686/ EEC and BGR 191

Safety boots 800/ 1700/ 3000

Certified according to inspection basis EN 345-1 – June 1997, BGR 191, Section 3.1.5.5.3 (trade association regulations and rules for health and safety at work – use of foot and legprotection) by approved and authorised centre no. 0299

Safety boots 800 for use when working with manually-operated high-pressure cleaners,can resist a pressure of up to 800 bar (11,600 PSI) and a lance recoil of up to 117 N, for a nozzle size of up to 1.0 mm, with up to 75 mm distance between the nozzle and the boots, and a feed rate of up to 0.2 m/ sec and water flow rate of up to 17.7 l/ min (4.68 USgal/ min)

Part no. Size 42 460 736 Size 43 460 737 Size 44 460 738 Size 45 460 739 Size 46 460 740

Safety boots 1700 for use when working with manually-operated high-pressure cleaners, can resist a pressure of up to 1,700 bar (24,650 PSI) and a lance recoil of up to 250 N, for a nozzle size of up to 1.0 mm, with up to 75 mm distance between the nozzle and the boots,and a feed rate of up to 0.2 m/ sec and water flow rate of up to 25.7 l/ min (6.8 USgal/ min)

Part no. Size 42 460 742 Size 43 460 743 Size 44 460 744 Size 45 460 745 Size 46 460 746 Size 48 492 086

Personal safety equipmentwww.dynajet-online.com

Safety boots 3000 for use when working with manually-operated high-pressure cleaners, can resist a pressure of up to 3,000 bar (43,500 PSI), tested for a lance recoil of up to 250 N, for a nozzle sizeof up to 1.0 mm, with up to 75 mm distance between the nozzle and the boots, and a feed rate ofup to 0.2 m/ sec and water flow rate of up to 25.7 l/ min (6.8 USgal/ min)

Part no. Size 42 499 649 Size 43 499 650 Size 44 499 651 Size 45 499 652 Size 46 499 653Size 47 499 654 Size 48 499 655

Safety helmet

Part no. Incl. ear defenders, visor and anti-fog visor (polycarbonate), 427 305 types conform with CE, EN 397: 1195, EN 352-3 Additional stainless steel visor 414 091 Replacement polycarbonate visor 414 092 Spare ear defenders 414 093

22 23MM 3474/08 GB MM 3474/08 GB

General accessories

Pressure gauge

Part no. For supply side, 0-10 bar, for monitoring the boost pressure, 001 160 004 inlet for GEKA coupling, outlet for GEKA coupling

Part no. PN 10 bar, 3⁄4” (DN 19), length of 20 m, 446 914 2x GEKA coupling

Supply hose

Part no. Suitable for: 446 926 max. 25 m, DN 8 high-pressure hose max. 25 m, DN 10 high-pressure hosemax. 20 m, 3⁄4” (DN 19) supply hose

Storage drum

GEKA quick-release couplers for water and air hoses with 3⁄8”– 11⁄4” NW (V)

Part no. Sealing, GEKA plus 413 895 Sealing 002 313.009 S 3⁄8” 018 535.004 S 1⁄2” 002 312,000 S 3⁄4” 001 387.007 S 1” 001 390.007 ET 3⁄8” 041 403.006 ET 1⁄2” 014 068.009 ET 3⁄4” 001 386.008 ET 1” 062 815.000 ET 11⁄4” 062 861.009 IT 1⁄2” 062 621.003 IT 3⁄4” 002 311.001 IT 1” 001 391.006 IT 11⁄4” 062 622.002



Booster pump

Part no. water pump 3.6 m3/ h with automatic switching 208 654.009 230 V, 0.75 kW, water-protected to IP 65, with check valve in the intake line

Additional filter

Aqua Soft liquid softener ASFE 2000

Antiseize lubricant

Part no. Also for supply side GEKA coupling inlet, GEKA coupling outlet, filter insert made of VA stainless steel, size 5”, filter unit 80 μm,loose delivery 460 418

Filter insert 5”, material: VA, 80 μm 495 841

Highly concentrated liquid softener, protects all water-immersed heating elements against calcification Part no. 1 litre 482 923 10 litres 497 086

Protects against damage and seizing in the threaded unions of stainless-steel connectionsPart no.

Tin 30 g 505 919Tin 500 g 498 633

General accessorieswww.dynajet-online.com

24 25

80 μm VA

80 μm VA

10 μm/50 μm

10 μm/50 μm

MM 3474/08 GB MM 3474/08 GB

Equipment concept for accessory filter packages, consists of: Part no. Accessory package 1 with 6x depth filters 10 μm TF, 496 5752x stainless-steel filter 80 μm VA, 2 m supply hose

Accessory package 2 with 6x depth filters 50 μm TF, 496 5762x stainless-steel filter 80 μm VA, 2 m supply hose

Possible filter inserts:

Type Fineness Dimensions Part no.Depth filter (Fig. 1) 10 μm TF 9 3⁄4” 496 557Depth filter (Fig. 1) 50 μm TF 9 3⁄4” 494 759Stainless steel (Fig. 2) 80 μm VA 9 3⁄4” 495 982

General accessories www.dynajet-online.com

Inserts for filter box

Filter packages

Max. supply pressure 8 bar (116 PSI) at 20 °C

Max. temperature 50 °C at 3 bar (43,5 PSI)

Max. volumetric flow rate 40 l/ min (10.6 USgal/ min)

Weight approx. 11 kg

Dimensions (L x W x H) 435 x 340 x 404 mm

Part no. 494 706

Technical data Filter station

For universal use with all high-pressure cleaning unitsin the Dynajet ® family

Robust aluminium type to minimise weight, corrosion-resistant Large filter surface and universal filter unit that can be adjusted to the type of dirt and the machine type ensure the highest flexibility on site Having replacement filters available on-site keeps changing times to a minimum Using a short hose, the filter unit is directly connected before the supply line of the high-pressure cleaning tool and protects the machine Increased working times through large filter surfaces in 2x2 parallel operation with minimised pressure loss at the same time 2x2 filter housing 9 3⁄4” in parallel connection* Robust design with 2 carrying handles 3-leg frames with solid rubber feet for reliable stability Covering plate made of aluminium Storage space for 4 replacement filter inserts Connection 3⁄4” GEKA coupling, outlet 3⁄4” GEKA coupling 2x cover coupling Stainless-steel filter can be washed out

Filter inserts not included in standard scope of supply.

Mobile Dynajet ® filter station

*Funct. principle for parallel connection:

Part no. Suitable for Dynajet ® surface cleaning systems, 426 844suction performance approx. 3,000 W, two-stage turbine, air output120 l/ sec. (31.75 USgal/ sec) without suction hose, for connecting toall DFS 2“ systems with suction connection, fully equipped with storage tank and suction pump

Part no. For connecting to Dynajet ® wet suction with spiral inlay, 447 558 length 15 m, temperature-resistant, suitable for all DWS and DFS systems

Part no. As safety protection when manually cleaning the interior of pipes 505 570and heat exchangers with flexible lances and hoses, fastened universally by using clamps, safety plate, storage compartment for various inserts, suitable for hoses 4/2, 5/2, 6/2

Protects the operator in case of nozzle or hose failure.

General accessorieswww.dynajet-online.com

Suction hose

Hose catcher

Dynajet ® wet suction

Fig. Restraining equipment = mounted on a typical heat exchanger



MM 3474/08 GB

Putzmeister Mörtelmaschinen GmbH

Max-Eyth-Straße 10 · D-72631 Aichtal · GermanyP.O. Box 2152 · D-72629 Aichtal · Germany

Telefon +49 (0 ) 7127 599-0Telefax +49 (0 ) 7127 599-743

Internet www.dynajet-online.comeMail [email protected]

Date post:	16-Apr-2018
Category:	Documents
Upload:	ngolien
View:	216 times
Download:	1 times

Dynajet UHP 170 - viskor.com · 2 3 MM 3474/08 GB MM 3474/08 GB Dynajet ® UHP 170 Maximum power...

Documents