6771- 84th Street S.E. Calgary, Alberta, Canada T2C 4T6
Phone: (403) 319-2333, Fax: (403) 319-2337 E-Mail: [email protected], Web Site: www.dynawinch.com
Product Line Index
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Table of Contents Section 1 Aluminum Van Truck Units Section 2 Mast and Derrick Truck Units Section 3 Wireline Skid Equipment Section 4 Drawworks Winch Equipment Section 5 Wireline Accessory Equipment
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771—84TH STREET SE, CALGARY, AB T2C 4T6
Section 1
Aluminum Van Body Truck Units Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 1 The following series of aluminum van body units are base units where modifications or design changes can be made to better fit the wireline service applications.
Slickline Van Units • SV1 - 120 Small radius rear body style with tarp roof cover on single axle truck
• SV1 - 140 Flat enclosed roof body style with rear doors on single axle truck
• SV1 - 160 Stepped down enclosed roof over drawworks style with rear doors on single axle truck
• SV1 - 160 Stepped down enclosed roof over drawworks style with rear doors on single axle 4 x 4 truck
• SV2 - 120 Small radius rear body style with tarp roof cover on tandem axle truck
• SV2 - 140 Flat enclosed roof body style with rear doors on tandem axle truck
Perforating and Logging Van Units • LV1 - 100 45 Degree rear slope body style with tarp roof cover on single axle truck
• LV1 - 100 45 Degree rear slope body style with tarp roof cover on single axle truck
• LV1 - 180 Sloped rear roof line body style with tarp roof on single axle truck
• LV1 - 190 Large radius round back rear roof line body style with tarp roof on single axle truck
• LV2 - 100 45 Degree rear slope body style with tarp roof cover on tandem axle truck
• LV2 - 100 45 Degree rear slope body style with tarp roof cover on tandem axle 6 x 6 truck
• LV2 - 110 6” Slope roof line and 45 degree rear slope body style with tarp roof on tandem axle truck
• LV2 - 180 Slopped rear roof line and square corner body style with tarp roof cover on tandem axle truck
Combination Van Units • CV1 - 195 Full rear rounded body style with tarp roof on single axle unimog
• CV2 - 120 Small radius rear body style with tarp roof cover on tandem axle truck
• CV3 - 120 Small radius rear body style with tarp roof cover on tri-axle truck
• CV3 - 160 Stepped down enclosed roof over drawworks style with rear doors on tri-axle truck
4 x 2 Single Axle HD Slickline Van Unit with Single Split Drum Drawworks
Model SV1-120 series is a single axle heavy duty aluminum van unit for slickline service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 120 series van body design has
small radius rear corner body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline sizes (up to 2 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
SV1-120 SE RI E S
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,300 kg (14,000 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
SA1-110-D Series Drawworks; 4 Spd Funk transmission chain drive with hydraulic motor Drive System with drop spool attachment
Drum Line Capacity: Slickline Split Drum: .108 / .125 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 750 mpm (2,400 fpm)
Pulling Power- Up to 4,300 kg (9,500 lbs)
Drop Attachment: Independent hydraulic drive motor with quick disconnect coupling on drop spool. 3,000m of .092” line on drop spool Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SV1-140 series is a single axle aluminum van unit for slickline service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 140 series van design has flat
enclosed roof body style over drawworks with double rear doors
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline line sizes (up to 2 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
SV1-140 SE RI E S
4 x 2 Single Axle Slickline Van Unit with Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters AC Power Supply: • 3,000 watt Inverter
Van Dimensions:
5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 5,400 kg (12,000 lbs) Rear Axle 9,080 kg (20,000 lbs)
Winch Hoist Specification:
SA1-200-D Series Drawworks; 2 Spd planetary gear box chain drive with hydraulic motor Drive System with drop spool attachment
Drum Line Capacity: Slickline Drum: .108” 7,600 M (25,000 ft)
Drum Drive Performance: Drum Speed - Up to 500 mpm (1,650 fpm)
Pulling Power- Up to 4,000 kg (9,000 lbs)
Drop Attachment: Independent hydraulic drive motor with quick disconnect chain drive on drop spool. 3,000m of .092” line on drop spool Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84TH STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SV1-160 series “Bomb” (drop spool) unit is a single axle van unit for slickline service work applications with a drop off drum spool system. This unit is designed to operate in an oilfield environment and can be modi-fied to perform other wireline service work applications.
Features: • 160 series van body design has
stepped down enclosed roof style over drawworks with double rear doors
• 100% aluminum frame all welded construction
• Light weight design • Generous quantity of external
storage compartments and racks • All weather climate controlled
operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired quantity of .092” or .108” slickline sizes
Spooling: • Linear bar spooler systems or
Overhead spooler system
SV1-160 SE R I E S
4 x 2 Single Axle Slickline Van (Bomb) Unit with Single Drop Spool Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
110V AC Power: • 3,000 watt inverter AC systems Drop Spools: • Quick removable drop off drum
spool system with on-board swing out jib-crane with DC electric winch
Van Dimensions:
3.05m L x 2.44m W (120 in L x 96 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 4,500 kg (10,000 lbs) Rear axle 7,200 kg (16,000 lbs)
Winch Hoist Specification:
SA1-520 Series Drawworks; Chain drive 2 spd planetary with hydraulic motor Drive System
Drum Line Capacity: Drop Spool Drum: .092” 3,000 M (10,000 ft)
Drum Drive Performance: Drum Speed - Up to 500 mpm (1,600 fpm)
Pulling Power- Up to 1,700 kg (3,700 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SV1-160 series 4 x 4 is a sin-gle axle heavy duty aluminum van unit for slickline service work applica-tions. This unit is designed to oper-ate in rough terrain oilfield environ-ment including artic, desert and tropi-cal conditions and can be modified to perform other wireline service work applications.
Features: • 160 series van body design has
stepped down enclosed roof style over drawworks with double rear doors
• 100% aluminum frame all welded construction
• Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired slickline sizes (up to 2 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
SV1-160 SE R I E S 4 X 4
4 x 4 Single Axle HD Slickline Van Unit with Single Split Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions: 5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,300 kg (14,000 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
SA1-110 Series Drawworks; 4 Spd Funk transmission chain drive with hydraulic motor Drive System
Drum Line Capacity: Slickline Split Drum: .108 / .150 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 700 mpm (2,300 fpm)
Pulling Power- Up to 4,800 kg (9,500 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SV2-120 series is a tandem axle heavy duty aluminum van unit for slickline service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 120 series van body design has
small radius rear corner body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline sizes (up to 4 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
SV2-120 SE R I E S
6 x 4 Tandem Axle HD Slickline Van Unit with Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.40m L x 2.48m W (252 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
SA2-810 Series Drawworks; Two independent Drum Drive Sys-tem, one (1) 4 spd Funk transmis-sion chain drive for Slickline drum, one (1) direct mount single spd planetary gear box drive for .188” line drum
Drum Line Capacity: Slickline Split Drum: .108 / .125 7,600 M (25,000 ft) of ea.
HD Slickline Drum: .188” 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 750 mpm (2,400 fpm)
Pulling Power- Up to 5,400 kg (12,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SV2-140 series is a tandem axle heavy duty aluminum van unit for slickline service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 140 series van design has flat
enclosed roof body style over drawworks with double rear doors
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline line sizes (up to 4 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
SV2-140 SE R I E S
6 x 4 Tandem Axle HD Slickline Van Unit with Single Split Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.40m L x 2.48m W (252 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
SA1-350 Series Drawworks; Direct drum mount single spd plane-tary gear box with 2 spd hydraulic motor Drive System
Split Drum Line Capacity: Drum: .108” / .160” E-Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84TH STREET SE CALGARY, AB T2C 4T6
Revised April 06
Aluminum Van Body Truck Units Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 1 The following series of aluminum van body units are base units where modifications or design changes can be made to better fit the wireline service applications.
Slickline Van Units • SV1 - 120 Small radius rear body style with tarp roof cover on single axle truck
• SV1 - 140 Flat enclosed roof body style with rear doors on single axle truck
• SV1 - 160 Stepped down enclosed roof over drawworks style with rear doors on single axle truck
• SV1 - 160 Stepped down enclosed roof over drawworks style with rear doors on single axle 4 x 4 truck
• SV2 - 120 Small radius rear body style with tarp roof cover on tandem axle truck
• SV2 - 140 Flat enclosed roof body style with rear doors on tandem axle truck
Perforating and Logging Van Units • LV1 - 100 45 Degree rear slope body style with tarp roof cover on single axle truck
• LV1 - 100 45 Degree rear slope body style with tarp roof cover on single axle truck
• LV1 - 180 Sloped rear roof line body style with tarp roof on single axle truck
• LV1 - 190 Large radius round back rear roof line body style with tarp roof on single axle truck
• LV2 - 100 45 Degree rear slope body style with tarp roof cover on tandem axle truck
• LV2 - 100 45 Degree rear slope body style with tarp roof cover on tandem axle 6 x 6 truck
• LV2 - 110 6” Slope roof line and 45 degree rear slope body style with tarp roof on tandem axle truck
• LV2 - 180 Slopped rear roof line and square corner body style with tarp roof cover on tandem axle truck
Combination Van Units • CV1 - 195 Full rear rounded body style with tarp roof on single axle unimog
• CV2 - 120 Small radius rear body style with tarp roof cover on tandem axle truck
• CV3 - 120 Small radius rear body style with tarp roof cover on tri-axle truck
• CV3 - 160 Stepped down enclosed roof over drawworks style with rear doors on tri-axle truck
Model LV1-100 series is a single axle heavy duty van unit for case hole logging and perforating service work applications. This unit is de-signed to operate in an oilfield envi-ronment including artic, desert and tropical conditions and can be modi-fied to perform other wireline service work applications.
Features: • 100 series van body design has
45 degree rear slope body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, single line drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV1-100 SE RI E S
4 x 2 Single Axle Case Hole Logging Van Unit with Single Split Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions: 5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 5,400 kg (12,000 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
LA1-410 Series Drawworks; Direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor Drive System
Split Drum Line Capacity: Drum: 5/16” / 3/16” E-Line 4,500 M (15,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
4 x 2 Single Axle Production Logging Van Unit with Single Drum Drawworks
Model LV1-100 series is a single axle heavy duty van unit for case hole production logging and perforat-ing service work applications. This unit is designed to operate in an oil-field environment including artic, de-sert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 100 series van body design has
45 degree rear slope body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, split drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV1-100 SE RI E S
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters AC Power Supply: • 10 kw hydraulic drive generator or • 3,000 watt Inverter Auxiliary Hydraulic System: • Auxiliary hydraulic system with
cooler for mast trailer option Van Dimensions: 5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 5,400 kg (12,000 lbs) Rear axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
LA2-400 Series Drawworks; Direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 3/16” E-Line 9,000 M (30,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LV1-180 series is a single axle heavy duty van unit for case hole logging and perforating service work applications. This unit is de-signed to operate in an oilfield envi-ronment including artic, desert and tropical conditions and can be modi-fied to perform other wireline service work applications.
Features: • 180 series van body design has
slopped rear roof line with square corner body style with tarpaulin roof cover overdrawworks com-partment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, single line drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV1-180 SE RI E S
4 x 2 Single Axle Case Hole Logging Van Unit with Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions: 5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 5,400 kg (12,000 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
LA1-400 Series Drawworks; Direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 5/16” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
Revised April 06
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Model LV1-190 series is a single axle heavy duty van unit for case hole logging and perforating service work applications. This unit is de-signed to operate in an oilfield envi-ronment including artic, desert and tropical conditions and can be modi-fied to perform other wireline service work applications.
Features: • 190 series van body design has
large radius rear body style with tarpaulin roof cover over draw-works compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, split drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV1-190 SE RI E S
4 x 4 Single Axle Case Hole Logging Van Unit with Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions: 5.45m L x 2.48m W (214 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,500 kg (14,400 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
LA1-400 Series Drawworks; Direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 5/16” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LV2-100 series is a tandem axle heavy duty van unit for open hole or case hole logging and perfo-rating service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 100 series van body design has
45 degree rear slope body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, split drum or double drum avail-able
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV2-100 SE RI E S
6 x 4 Tandem Axle HD Logging Van Unit with Single or Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.09m L x 2.48m W (240 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,300 kg (14,000 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-100 Series Drawworks; 3 spd Funk transmission chain drive with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 5/16” E-Line 7,600 M (25,000 ft)
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 3 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LV2-100 series 6 x 6 is a tan-dem axle heavy duty van unit for open hole and case hole logging and perforating service work applications. This unit is designed to operate in rough terrain oilfield environment including artic, desert and tropical conditions, can be modified to per-form other wireline service work ap-plications.
Features: • 100 series van body design has
45 degree rear slope body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, single line drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV2-100 SE RI E S 6 X 6
6 x 6 Tandem Axle HD Logging Van Unit with Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring & Spooling: • In-line measure head or con-
ventional • Electronic digital meters,
weight, speed & depth • Overhead spooler system Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.40m L x 2.48m W (252 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended 6 x 6 Chassis:
Front Axle 8,170 kg (18,000 lbs) Rear Tandem Axles 19,900 kg (44,000 lbs)
Winch Hoist Specification:
LA2-400R Series Drawworks; Two independent Direct drum mount 2 spd planetary gear box with 2 spd hydraulic motors Drive System with rear drum raising op-tion
Dual Drum Line Capacity: Drum: 15/32” / 7/32” E-Line 5,000 M (16,400 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LV2-110 series is a tandem axle heavy duty van unit for open hole or case hole logging and perfo-rating service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 110 series van body design has
6” slope roof line with 45 degree rear slope body style with tarpau-lin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions Wireline Accessories Options: Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, single line drum or double drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV2-110 SE R I E S
6 x 4 Tandem Axle HD Logging Van Unit with Single or Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.09m L x 2.48m W (240 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-110 Series Drawworks; 3 spd Funk transmission chain drive with 2 spd hydraulic motor drive system
Drum Line Capacity: Split Drum: 5/16” / 7/32” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 3 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LV2-180 series is a tandem axle heavy duty van unit for open hole or case hole logging and perfo-rating service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 180 series van body design has
slopped rear roof line with square corner body style with tarpaulin roof cover over drawworks com-partment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Optimized external storage com-
partments and tool racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired braided E-Line sizes, single line drum available
Spooling: • Linear bar spooler systems or
Overhead spooler system
LV2-180 SE RI E S
6 x 4 Tandem Axle HD Logging Van Unit with Single or Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.09m L x 2.48m W (240 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA2-400 Series Drawworks; Two independent direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor Drive Systems
Drum Line Capacity: Dual Drums: 5/16” & 7/32” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Aluminum Van Body Truck Units Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 1 The following series of aluminum van body units are base units where modifications or design changes can be made to better fit the wireline service applications.
Slickline Van Units • SV1 - 120 Small radius rear body style with tarp roof cover on single axle truck
• SV1 - 140 Flat enclosed roof body style with rear doors on single axle truck
• SV1 - 160 Stepped down enclosed roof over drawworks style with rear doors on single axle truck
• SV1 - 160 Stepped down enclosed roof over drawworks style with rear doors on single axle 4 x 4 truck
• SV2 - 120 Small radius rear body style with tarp roof cover on tandem axle truck
• SV2 - 140 Flat enclosed roof body style with rear doors on tandem axle truck
Perforating and Logging Van Units • LV1 - 100 45 Degree rear slope body style with tarp roof cover on single axle truck
• LV1 - 100 45 Degree rear slope body style with tarp roof cover on single axle truck
• LV1 - 180 Sloped rear roof line body style with tarp roof on single axle truck
• LV1 - 190 Large radius round back rear roof line body style with tarp roof on single axle truck
• LV2 - 100 45 Degree rear slope body style with tarp roof cover on tandem axle truck
• LV2 - 100 45 Degree rear slope body style with tarp roof cover on tandem axle 6 x 6 truck
• LV2 - 110 6” Slope roof line and 45 degree rear slope body style with tarp roof on tandem axle truck
• LV2 - 180 Slopped rear roof line and square corner body style with tarp roof cover on tandem axle truck
Combination Van Units • CV1 - 195 Full rear rounded body style with tarp roof on single axle unimog
• CV2 - 120 Small radius rear body style with tarp roof cover on tandem axle truck
• CV3 - 120 Small radius rear body style with tarp roof cover on tri-axle truck
• CV3 - 160 Stepped down enclosed roof over drawworks style with rear doors on tri-axle truck
Model CV1-195 series is a single axle heavy duty aluminum van unit for combination Slickline and Braided line service work applications. This unit is designed to operate in an oil-field environment including artic, de-sert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 195 series van body design has
full rear rounded body style with tarpaulin roof cover over draw-works compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • External storage compartments
and racks • All weather climate controlled
operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline and braided line sizes
Spooling: • Linear bar spooler systems or
Overhead spooler system
CV1-195 SE RI E S
4 x 4 Unimog Single Axle Combination Van Unit with Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator
Van Dimensions:
4.14m L x 2.33m W (162 in L x 92 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 5,400 kg (12,000 lbs) Rear Axle 9,080 kg (20,000 lbs)
Winch Hoist Specification:
CA2-800 Series Drawworks; Two independent direct drum mount single spd planetary gear box with 2 spd hydraulic motor Drive Systems
Drum Line Capacity: Slickline Drum: .108 7,600 M (25,000 ft)
Braided Line Drum: 7/32” 7,600 M (25,000 ft)
Drum Drive Performance: Drum Speed - Up to 480 mpm (1,570 fpm)
Pulling Power- Up to 2,400 kg (5,300 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model CV2-120 series is a tandem axle heavy duty aluminum van unit for combination Slickline and Braided line service work applications, carry-ing up to four different drum lines. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 120 series van body design has
small radius rear corner body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• All weather thermal insulation • Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline and braided line sizes (up to 4 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
CV2-120 SE RI E S
6 x 4 Tandem Axle Combination Van Unit with Double Split Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.40m L x 2.48m W (252 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,300 kg (14,000 lbs) Rear Tandem Axle 18,100 kg (40,000 lbs)
Winch Hoist Specification:
CA2-920 Series Drawworks; Two independent Funk 4 Spd Transmission Chain Drive System
Drum Line Capacity: Slickline Split Drum: .108 / .125 7,600 M (25,000 ft) of ea.
Braided Line Split Drum: 3/16” / 1/4” 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 750 mpm (2,400 fpm)
Pulling Power- Up to 4,300 kg (9,500 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model CV3-120 series is a tri-axle (3)heavy duty aluminum van unit for combination Slickline and Braided line service work applications, carry-ing up to four different drum lines. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 120 series van body design has
small radius rear corner body style with tarpaulin roof cover over drawworks compartment
• 100% aluminum frame all welded construction
• Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline and braided line sizes (up to 4 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
CV3-120 SE RI E S
8 x 6 Tri-Axle Combination Van Unit with Double Split Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.40m L x 2.60m W (252 in L x 102 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs)
Rear Tri-Axle 25,800 kg (57,000 lbs)
Winch Hoist Specification:
CA2-945 Series Drawworks; Two independent Funk Transmis-sion Chain Drive System, one (1) 4 spd for Slickline drum, one (1) 3 spd for Braided line drum
Drum Line Capacity: Slickline Split Drum: .108 / .150 7,600 M (25,000 ft) of ea.
Braided Line Split Drum: 1/4” / 7/32” 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 750 mpm (2,400 fpm)
Pulling Power- Up to 5,400 kg (12,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model CV3-120 series is a tri-axle (3)heavy duty aluminum van unit for combination Slickline and Braided line service work applications, carry-ing up to four different drum lines. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 160 series van body design has
stepped down enclosed roof style over drawworks with double rear doors
• 100% aluminum frame all welded construction
• Light weight design • Generous quantity of external
storage compartments and racks • Large all weather climate con-
trolled operator’s cabin • Ergonomic design control panel • Low noise level • Operator’s captain’s chair • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired slickline and braided line sizes (up to 4 lines)
Spooling: • Linear bar spooler systems or
Overhead spooler system
CV3-160 SE R I E S
8 x 6 Tri-Axle Combination Van Unit with Double Split Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters Generator: • 10 kw hydraulic drive generator Grease Injector: • 5K hydraulic onboard grease
injector system
Van Dimensions:
6.40m L x 2.60m W (252 in L x 102 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs)
Rear Tri-Axle 25,800 kg (57,000 lbs)
Winch Hoist Specification:
CA2-720 Series Drawworks; Two independent Drum Drive Sys-tem, one (1) 4 spd Funk transmis-sion chain drive for Slickline drum, one (1) direct mount 2 spd planetary gear box drive for Braided line drum
Drum Line Capacity: Slickline Split Drum: .108 / .150 7,600 M (25,000 ft) of ea.
Braided Line Split Drum: 1/4” / 7/32” 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 750 mpm (2,400 fpm)
Pulling Power- Up to 5,400 kg (12,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771—84TH STREET SE, CALGARY, AB T2C 4T6
Section 2
Mast and Derrick Truck Units Product Line Model Series Numbers
Section 2
The following series of mast and derrick truck units are base units where modifications or design changes can be made to better fit the wireline service applications.
Logging Telescoping Mast Truck Units
• LM1 - 200 45’ Crown to ground hydraulic telescoping mast on single axle truck
• LM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
• LM3 - 210 48’ Crown to ground hydraulic telescoping mast on tri-axle truck
Logging Derrick Truck Units
• LD2 - 200 45’ Crown to ground derrick on tandem axle truck
• LD2 - 205 45’ Crown to ground derrick with slant hole option on tandem axle truck
Swabbing Telescoping Mast Truck Units
• WM2 - 100 40’ Stiff mast on tandem axle truck
• WM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
Swabbing Derrick Truck Units
• WD2 - 200 45’ Crown to ground derrick on tandem axle truck
• WD2 - 300 45’ Crown to ground derrick on tandem axle truck
• WD3 - 215 48’ Crown to ground slant hole derrick on tri-axle truck
• WD3 - 310 48’ Crown to ground derrick on tri-axle truck
• WD3 - 315 48’ Crown to ground slant hole derrick on tri-axle truck
Combination Derrick Truck Units
• CD3 - 210 48’ Crown to ground derrick on tri-axle truck
Combination Crane and Wireline Truck Units
• LC2 - 600 Rear mount boom crane with swivel cabin and logging drawworks on tandem axle truck • SC1 - 200 Light duty rear mount articulating crane and WL slickline drawworks on single axle truck
• SC1 - 400 Rear mount articulating crane and WL slickline drawworks with van body on single axle truck
• SC1 - 700 Rear corner mount boom crane with van body and slickline drawworks on single axle truck
• SC2 - 600 Rear mount boom crane with swivel cabin and slickline drawworks on tandem axle truck
• SC2 - 700 Rear corner mount boom crane with van body and slickline drawworks on tandem axle truck
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
4 x 2 Single Axle Mast Logging Unit 45 ft. Telescoping Mast with Single Drum
Model LM1-200 series is a single axle with hydraulic telescoping mast with reach to 45 ft. for logging and perforating service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 200 series operator control cabin
is independent from deck and manufactured from 100% alumi-num structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Hydraulic telescoping mast has
an extended reach of 45 ft. from ground to crown
• Rear hydraulic down rigger cylin-ders incorporated in rear bumper
• Optimized external storage compart-ments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in der-
rick A-Frame
• Hydraulic spooler control
LM1-200 SE RI E S
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
1.82m L x 2.48m W (72 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,400 kg (14,000 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
LA1-400 Series Drawworks; Direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 5/16” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 1 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LM2-210 series is a tandem axle with hydraulic telescoping mast with reach to 48 ft. for logging and perforating service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 200 series operator control cabin
is independent from deck and manufactured from 100% alumi-num structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Hydraulic telescoping mast has
an extended reach of 48 ft. from ground to crown
• Rear hydraulic down rigger cylin-ders incorporated in rear bumper
• Optimized external storage compart-ments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in der-
rick A-Frame
• Hydraulic spooler control
LM2-210 SE RI E S
6 x 4 Tandem Axle Mast Logging Unit 48 ft. Telescoping Mast with Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-100 Series Drawworks; 3 spd Funk transmission chain drive with 2 spd hydraulic motor drive system
Drum Line Capacity: Drum: 5/16” E-Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 400 mpm (1,300 fpm)
Pulling Power- Up to 5,600 kg (12,500 lbs)
Has excellent low speed for logging, as low as 3 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LM3-210 series is a tri-axle with hydraulic telescoping mast with reach to 48 ft. for logging and perfo-rating service work applications. This unit is designed to operate in an oil-field environment including artic, de-sert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 200 series operator control cabin
is independent from deck and manufactured from 100% alumi-num structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Hydraulic telescoping mast has
an extended reach of 48 ft. from ground to crown
• Rear hydraulic down rigger cylin-ders incorporated in rear bumper
• Optimized external storage compart-ments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in der-
rick A-Frame
• Hydraulic spooler control
LM3-210 SE RI E S
8 x 6 Tri-Axle Mast Logging Unit 48 ft. Telescoping Mast with Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.60m W (98 in L x 102 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs) Rear Tri-Axles 25,800 kg (57,000 lbs)
Winch Hoist Specification:
LA1-200 Series Drawworks; 2 spd hydraulic motor with single speed planetary gear box chain drive system
Drum Line Capacity: Drum: 3/8” E-Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 340 mpm (1,100 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Has good smooth low speed for logging, as low as 6 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Mast and Derrick Truck Units Product Line Model Series Numbers
Section 2
The following series of mast and derrick truck units are base units where modifications or design changes can be made to better fit the wireline service applications.
Logging Telescoping Mast Truck Units
• LM1 - 200 45’ Crown to ground hydraulic telescoping mast on single axle truck
• LM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
• LM3 - 210 48’ Crown to ground hydraulic telescoping mast on tri-axle truck
Logging Derrick Truck Units
• LD2 - 200 45’ Crown to ground derrick on tandem axle truck
• LD2 - 205 45’ Crown to ground derrick with slant hole option on tandem axle truck
Swabbing Telescoping Mast Truck Units
• WM2 - 100 40’ Stiff mast on tandem axle truck
• WM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
Swabbing Derrick Truck Units
• WD2 - 200 45’ Crown to ground derrick on tandem axle truck
• WD2 - 300 45’ Crown to ground derrick on tandem axle truck
• WD3 - 215 48’ Crown to ground slant hole derrick on tri-axle truck
• WD3 - 310 48’ Crown to ground derrick on tri-axle truck
• WD3 - 315 48’ Crown to ground slant hole derrick on tri-axle truck
Combination Derrick Truck Units
• CD3 - 210 48’ Crown to ground derrick on tri-axle truck
Combination Crane and Wireline Truck Units
• LC2 - 600 Rear mount boom crane with swivel cabin and logging drawworks on tandem axle truck • SC1 - 200 Light duty rear mount articulating crane and WL slickline drawworks on single axle truck
• SC1 - 400 Rear mount articulating crane and WL slickline drawworks with van body on single axle truck
• SC1 - 700 Rear corner mount boom crane with van body and slickline drawworks on single axle truck
• SC2 - 600 Rear mount boom crane with swivel cabin and slickline drawworks on tandem axle truck
• SC2 - 700 Rear corner mount boom crane with van body and slickline drawworks on tandem axle truck
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Model LD2-200 series is a tandem axle 1 pc raising derrick unit for heavy duty logging and swabbing service work applications. This log-ging unit comes with heavy rated capacity derrick, climate controlled operator’s cabin and tool storage compartments. This unit is de-signed to operate in an oilfield envi-ronment including artic, desert and tropical conditions. Features: • 200 series operator control
cabin is independent from deck and manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • 1 pc hydraulic raising derrick
with raised reach of 45 ft. from ground to crown
• Rear hydraulic down rigger cyl-inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for op-
erations Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
LD2-200 SE R I E S
6 x 4 Tandem Axle Derrick Logging Unit 45 ft. Derrick and Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-200 Series Drawworks; 2 spd hydraulic motor with single speed planetary gear box chain drive system
Drum Line Capacity: Drum: 3/8” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 340 mpm (1,100 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Has good smooth low speed for logging, as low as 6 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LD2-205 series is a tandem axle 1 pc raising derrick with slant hole option for heavy duty logging and swabbing service work applica-tions. This logging unit comes with heavy rated capacity derrick, cli-mate controlled operator’s cabin and tool storage compartments. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions. Features: • 200 series operator control
cabin is independent from deck and manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Slant hole application 1 pc der-
rick with raised reach of 45 ft. from ground to crown
• Rear hydraulic down rigger cyl-inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for op-
erations Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
LD2-205 SE R I E S
6 x 4 Tandem Axle Derrick Logging Unit 45 ft. Slant Hole Derrick and Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-300 Series Drawworks; Direct drum mount single spd plane-tary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 3/8” E-Line 6,100 M (20,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 320 mpm (1,050 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Has good smooth low speed for logging, as low as 6 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Mast and Derrick Truck Units Product Line Model Series Numbers
Section 2
The following series of mast and derrick truck units are base units where modifications or design changes can be made to better fit the wireline service applications.
Logging Telescoping Mast Truck Units
• LM1 - 200 45’ Crown to ground hydraulic telescoping mast on single axle truck
• LM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
• LM3 - 210 48’ Crown to ground hydraulic telescoping mast on tri-axle truck
Logging Derrick Truck Units
• LD2 - 200 45’ Crown to ground derrick on tandem axle truck
• LD2 - 205 45’ Crown to ground derrick with slant hole option on tandem axle truck
Swabbing Telescoping Mast Truck Units
• WM2 - 100 40’ Stiff mast on tandem axle truck
• WM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
Swabbing Derrick Truck Units
• WD2 - 200 45’ Crown to ground derrick on tandem axle truck
• WD2 - 300 45’ Crown to ground derrick on tandem axle truck
• WD3 - 215 48’ Crown to ground slant hole derrick on tri-axle truck
• WD3 - 310 48’ Crown to ground derrick on tri-axle truck
• WD3 - 315 48’ Crown to ground slant hole derrick on tri-axle truck
Combination Derrick Truck Units
• CD3 - 210 48’ Crown to ground derrick on tri-axle truck
Combination Crane and Wireline Truck Units
• LC2 - 600 Rear mount boom crane with swivel cabin and logging drawworks on tandem axle truck • SC1 - 200 Light duty rear mount articulating crane and WL slickline drawworks on single axle truck
• SC1 - 400 Rear mount articulating crane and WL slickline drawworks with van body on single axle truck
• SC1 - 700 Rear corner mount boom crane with van body and slickline drawworks on single axle truck
• SC2 - 600 Rear mount boom crane with swivel cabin and slickline drawworks on tandem axle truck
• SC2 - 700 Rear corner mount boom crane with van body and slickline drawworks on tandem axle truck
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Model WM2-100 series is a tandem axle with 1pc stiff mast with reach to 40 ft. for swabbing and other special-ized service work applications. This unit is designed to operate in an oil-field environment including artic, de-sert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • 200 series operator control cabin
is independent from deck and manufactured from 100% alumi-num structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Hydraulic raising 1pc stiff mast
has reach of 40 ft. from ground to crown
• Rear hydraulic down rigger cylin-ders incorporated in rear bumper
• Optimized external storage compart-ments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in der-
rick A-Frame
• Hydraulic spooler control
WM2-100 SE R I E S
6 x 4 Tandem Axle Mast Swab Rig 40 ft. Stiff Mast with Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg
Winch Hoist Specification:
LA1-300 Series Drawworks; Direct drum mount single spd plane-tary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 7/16” E-Line 4,000 M (13,200 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 320 mpm (1,050 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Has good smooth low speed for logging, as low as 6 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model WM2-210 series is a tandem axle with hydraulic telescoping mast with reach to 48 ft. for swabbing and other specialized service work appli-cations. This unit is designed to op-erate in an oilfield environment in-cluding artic, desert and tropical con-ditions and can be modified to per-form other wireline service work ap-plications.
Features: • 200 series operator control cabin
is independent from deck and manufactured from 100% alumi-num structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Hydraulic telescoping mast has
an extended reach of 48 ft. from ground to crown
• Rear hydraulic down rigger cylin-ders incorporated in rear bumper
• Optimized external storage compart-ments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in der-
rick A-Frame
• Hydraulic spooler control
WM2-210 SE R I E S
6 x 4 Tandem Axle Mast Swab Rig 48 ft. Telescoping Mast with Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
WA1-300 Series Drawworks; Direct drum mount single spd plane-tary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 7/32” E-Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 310 mpm (1,000 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Has good smooth low speed, as low as 6 mpm. Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Mast and Derrick Truck Units Product Line Model Series Numbers
Section 2
The following series of mast and derrick truck units are base units where modifications or design changes can be made to better fit the wireline service applications.
Logging Telescoping Mast Truck Units
• LM1 - 200 45’ Crown to ground hydraulic telescoping mast on single axle truck
• LM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
• LM3 - 210 48’ Crown to ground hydraulic telescoping mast on tri-axle truck
Logging Derrick Truck Units
• LD2 - 200 45’ Crown to ground derrick on tandem axle truck
• LD2 - 205 45’ Crown to ground derrick with slant hole option on tandem axle truck
Swabbing Telescoping Mast Truck Units
• WM2 - 100 40’ Stiff mast on tandem axle truck
• WM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
Swabbing Derrick Truck Units
• WD2 - 200 45’ Crown to ground derrick on tandem axle truck
• WD2 - 300 45’ Crown to ground derrick on tandem axle truck
• WD3 - 215 48’ Crown to ground slant hole derrick on tri-axle truck
• WD3 - 310 48’ Crown to ground derrick on tri-axle truck
• WD3 - 315 48’ Crown to ground slant hole derrick on tri-axle truck
Combination Derrick Truck Units
• CD3 - 210 48’ Crown to ground derrick on tri-axle truck
Combination Crane and Wireline Truck Units
• LC2 - 600 Rear mount boom crane with swivel cabin and logging drawworks on tandem axle truck • SC1 - 200 Light duty rear mount articulating crane and WL slickline drawworks on single axle truck
• SC1 - 400 Rear mount articulating crane and WL slickline drawworks with van body on single axle truck
• SC1 - 700 Rear corner mount boom crane with van body and slickline drawworks on single axle truck
• SC2 - 600 Rear mount boom crane with swivel cabin and slickline drawworks on tandem axle truck
• SC2 - 700 Rear corner mount boom crane with van body and slickline drawworks on tandem axle truck
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Model WD2-200 series is a tandem axle 1 pc raising derrick option for heavy duty logging and swabbing service work applications. This log-ging unit comes with heavy rated capacity derrick, climate controlled operator’s cabin and tool storage compartments. This unit is de-signed to operate in an oilfield envi-ronment including artic, desert and tropical conditions. Features: • 200 series operator control
cabin is independent from deck and manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • 1 pc derrick with raised reach of
45 ft. from ground to crown • Rear hydraulic down rigger cyl-
inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for op-
erations Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
WD2-200 SE RI E S
6 x 4 Tandem Axle Derrick HD Swab Unit 45 ft. Derrick and Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-300 Series Drawworks; Direct drum mount single spd plane-tary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 1/2” E-Line 4,000 M (13,200 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 320 mpm (1,050 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model WD2-300 series Swab Rig unit is a tandem axle 1 pc raising derrick unit for heavy duty swabbing service work applications. This swab rig comes with heavy rated capacity derrick, operator’s cabin and tool storage compartments. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions. Features: • 300 series operator control
cabin is mounted on top of rear deck, manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • 1 pc hydraulic raising derrick
with raised reach of 45 ft. from ground to crown
• Rear hydraulic down rigger cyl-inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for op-
erations Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
WD2-300 SE R I E S
6 x 4 Tandem Axle HD Swab Rig 45 ft. Derrick and Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.44m L x 1.82m W (96 in L x 72 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-200 Series Drawworks; 2 spd hydraulic motor with single speed planetary gear box chain drive system
Drum Line Capacity: Drum: 1/2” E-Line 4,000 M (13,200 ft)
Drum Drive Performance: Drum Speed - Up to 340 mpm (1,100 fpm)
Pulling Power- Up to 9,000 kg (20,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model WD3-215 series Swab Rig unit is a tri-axle 1 pc raising derrick with slant hole option unit for heavy duty swabbing service work applica-tions. This swab rig comes with heavy capacity rated derrick, opera-tor’s cabin and tool storage com-partments. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions. Features: • 200 series operator control
cabin is independent from deck and manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Slant hole application 1 pc hy-
draulic raising derrick with raised reach of 48 ft. from ground to crown
• Rear hydraulic down rigger cyl-inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems, friendly control design for operations
Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
WD3-215 SE R I E S
8 x 6 Tri-Axle Derrick HD Swab Rig 48 ft. Slant Hole Derrick and Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spooler carriage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,260 kg (16,000 lbs) Rear axles 26,300 kg (58,000 lbs)
Winch Hoist Specification: Example: Chain drive planetary gear box with 2 speed hydraulic motor drive system with 9/16” line
Max Speed - Core 125 mpm (400 fpm) Max Speed - Rim 340 mpm (1,100 fpm) Max Pull - Core 11,500 kg (25,100 lbs) Max Pull - Rim 4,200 kg (9,200 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity: Typical drum design can hold
3,700 M (12,000 ft) of 1/2 in or 9/16 in Swab Line
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model WD3-310 series Swab Rig unit is a tri-axle 1 pc raising derrick unit for heavy duty swabbing ser-vice work applications. This swab rig comes with heavy capacity rated derrick, operator’s cabin and tool storage compartments. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions. Features: • 300 series operator control
cabin is mounted on top of rear deck, manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • 1 pc hydraulic raising derrick
with raised reach of 48 ft. from ground to crown
• Rear hydraulic down rigger cyl-inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for op-
erations Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
WD3-310 SE R I E S
8 x 6 Tri-Axle HD Swab Rig 48 ft. Derrick and Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spooler carriage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.84m L x 1.82m W (120 in L x 72 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,260 kg (16,000 lbs) Rear Tri-Axles 26,300 kg (58,000 lbs)
Winch Hoist Specification:
LA1-200 Series Drawworks; 2 spd hydraulic motor with single speed planetary gear box chain drive system
Drum Line Capacity: Drum: 9/16” E-Line 3,700 M (12,000 ft)
Drum Drive Performance: Drum Speed - Up to 340 mpm (1,100 fpm)
Pulling Power- Up to 9,000 kg (20,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model WD3-315 series Swab Rig unit is a tri-axle 1 pc raising derrick with slant hole option unit for heavy duty swabbing service work applica-tions. This swab rig comes with heavy capacity rated derrick, opera-tor’s cabin and tool storage com-partments. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions. Features: • 300 series operator control
cabin is mounted on top of rear deck, manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Slant hole application 1 pc hy-
draulic raising derrick with raised reach of 48 ft. from ground to crown
• Rear hydraulic down rigger cyl-inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems, friendly control design for operations
Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
WD3-315 SE R I E S
8 x 6 Tri-Axle Derrick HD Swab Rig 48 ft. Slant Hole Derrick and Single Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spooler carriage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.84m L x 1.82m W (120 in L x 72 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,260 kg (16,000 lbs) Rear Tri-Axles 26,300 kg (58,000 lbs)
Winch Hoist Specification:
LA1-200 Series Drawworks; 2 spd hydraulic motor with single speed planetary gear box chain drive system
Drum Line Capacity: Drum: 9/16” E-Line 3,700 M (12,000 ft)
Drum Drive Performance: Drum Speed - Up to 340 mpm (1,100 fpm)
Pulling Power- Up to 9,000 kg (20,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Mast and Derrick Truck Units Product Line Model Series Numbers
Section 2
The following series of mast and derrick truck units are base units where modifications or design changes can be made to better fit the wireline service applications.
Logging Telescoping Mast Truck Units
• LM1 - 200 45’ Crown to ground hydraulic telescoping mast on single axle truck
• LM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
• LM3 - 210 48’ Crown to ground hydraulic telescoping mast on tri-axle truck
Logging Derrick Truck Units
• LD2 - 200 45’ Crown to ground derrick on tandem axle truck
• LD2 - 205 45’ Crown to ground derrick with slant hole option on tandem axle truck
Swabbing Telescoping Mast Truck Units
• WM2 - 100 40’ Stiff mast on tandem axle truck
• WM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
Swabbing Derrick Truck Units
• WD2 - 200 45’ Crown to ground derrick on tandem axle truck
• WD2 - 300 45’ Crown to ground derrick on tandem axle truck
• WD3 - 215 48’ Crown to ground slant hole derrick on tri-axle truck
• WD3 - 310 48’ Crown to ground derrick on tri-axle truck
• WD3 - 315 48’ Crown to ground slant hole derrick on tri-axle truck
Combination Derrick Truck Units
• CD3 - 210 48’ Crown to ground derrick on tri-axle truck
Combination Crane and Wireline Truck Units
• LC2 - 600 Rear mount boom crane with swivel cabin and logging drawworks on tandem axle truck • SC1 - 200 Light duty rear mount articulating crane and WL slickline drawworks on single axle truck
• SC1 - 400 Rear mount articulating crane and WL slickline drawworks with van body on single axle truck
• SC1 - 700 Rear corner mount boom crane with van body and slickline drawworks on single axle truck
• SC2 - 600 Rear mount boom crane with swivel cabin and slickline drawworks on tandem axle truck
• SC2 - 700 Rear corner mount boom crane with van body and slickline drawworks on tandem axle truck
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Model CD3-210 series is a tri-axle 1 pc raising derrick for heavy duty logging and swabbing service work applications. This unit comes with heavy rated capacity derrick, cli-mate controlled operator’s cabin and tool storage compartments. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions. Features: • 200 series operator control
cabin is independent from deck and manufactured from 100% aluminum structure
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • 1 pc derrick with raised reach of
48 ft. from ground to crown • Rear hydraulic down rigger cyl-
inders incorporated in rear bumper
• Optimized external storage com-partments and tool racks
• Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for op-
erations Wireline Accessories Options: Drawworks & Spooling: • Multiple size single drum draw-
works to fit desired cable sizes • Integrated spooler system in
derrick A-Frame
• Hydraulic spooler control
CD3-210 SE R I E S
8 x 6 Tri-Axle Derrick Log / Swab Unit 48 ft Derrick and Double Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Integrated measure wheel and
electronic load cell in spool car-riage assembly
• Electronic display meters for line speed, depth and tension
Generator: • 10 kw hydraulic drive generator Auxiliary Winch: • Hydraulic drive auxiliary winch
Cab Dimensions:
2.48m L x 2.48m W (98 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs) Rear Tri-Axles 25,800 kg (57,000 lbs)
Winch Hoist Specification:
CA2-860 Series Drawworks; Two independent Drum Drive Sys-tem, E-Line drum has direct drum mount 2 spd planetary gear box with 2 spd hydraulic motor, Swab drum has 2 spd hydraulic motor with single speed planetary gear box chain drive system
Drum Line Capacity: E-Line Drum: 5/16” 6,100 M (20,000 ft)
Swab Drum: 7/16” 4,000 M (13,200 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 320 mpm (1,050 fpm)
Pulling Power- Up to 6,300 kg (13,800 lbs)
Has good smooth low speed for logging, as low as 6 mpm.
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Mast and Derrick Truck Units Product Line Model Series Numbers
Section 2
The following series of mast and derrick truck units are base units where modifications or design changes can be made to better fit the wireline service applications.
Logging Telescoping Mast Truck Units
• LM1 - 200 45’ Crown to ground hydraulic telescoping mast on single axle truck
• LM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
• LM3 - 210 48’ Crown to ground hydraulic telescoping mast on tri-axle truck
Logging Derrick Truck Units
• LD2 - 200 45’ Crown to ground derrick on tandem axle truck
• LD2 - 205 45’ Crown to ground derrick with slant hole option on tandem axle truck
Swabbing Telescoping Mast Truck Units
• WM2 - 100 40’ Stiff mast on tandem axle truck
• WM2 - 210 48’ Crown to ground hydraulic telescoping mast on tandem axle truck
Swabbing Derrick Truck Units
• WD2 - 200 45’ Crown to ground derrick on tandem axle truck
• WD2 - 300 45’ Crown to ground derrick on tandem axle truck
• WD3 - 215 48’ Crown to ground slant hole derrick on tri-axle truck
• WD3 - 310 48’ Crown to ground derrick on tri-axle truck
• WD3 - 315 48’ Crown to ground slant hole derrick on tri-axle truck
Combination Derrick Truck Units
• CD3 - 210 48’ Crown to ground derrick on tri-axle truck
Combination Crane and Wireline Truck Units
• LC2 - 600 Rear mount boom crane with swivel cabin and logging drawworks on tandem axle truck • SC1 - 200 Light duty rear mount articulating crane and WL slickline drawworks on single axle truck
• SC1 - 400 Rear mount articulating crane and WL slickline drawworks with van body on single axle truck
• SC1 - 700 Rear corner mount boom crane with van body and slickline drawworks on single axle truck
• SC2 - 600 Rear mount boom crane with swivel cabin and slickline drawworks on tandem axle truck
• SC2 - 700 Rear corner mount boom crane with van body and slickline drawworks on tandem axle truck
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Model LC2-600 series is a tandem axle combination crane and wireline unit for logging service work applica-tions. This unit is designed to oper-ate in an oilfield environment includ-ing artic, desert and tropical condi-tions and can be modified to perform slickline service work applications.
Features: • 600 series has integrated swivel
operator’s control cab and draw-works compartment
• 25 degrees rotating cabin and drawworks compartment
• External storage compartments • 100% aluminum operator’s con-
trol cabin section • All weather thermal insulated cabin
with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Rear mount hydraulic boom
crane • Rear and front out rigger cylin-
ders • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired E-line Spooling: • Linear bar spooler systems or
overhead spooling system
LC2-600 SE RI E S
6 x 4 Tandem Axle Logging Crane Unit Rear Boom Crane and WL Swivel Cabin
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Measure head • Electronic display meters for
line speed, depth and tension Generator: • 10 kw hydraulic drive generator Boom Crane: • Boom reach depending on
crane option • 10, 12, 15, 18 & 20 Ton options
Swivel Cabin Dimensions:
3.81m L x 2.33m W (150 in L x 92 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
LA1-300 Series Drawworks; Direct drum mount single spd plane-tary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: 7/32” E-Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 350 mpm (1,150 fpm)
Pulling Power- Up to 4,400 kg (9,700 lbs)
Has good smooth low speed, as low as 6 mpm.
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SC1-200 series is a single axle combination crane and wireline unit for light duty slickline service work applications. This unit is de-signed to operate in an oilfield envi-ronment including artic, desert and tropical conditions and can be modi-fied to perform other wireline service work applications.
Features: • 100% aluminum operator’s con-
trol cabin section • All weather thermal insulated cabin
with all weather climate con-trolled interior
• External storage compartments • Ergonomic design control panel • Low noise level • Rear articulating hydraulic crane • Rear hydraulic out rigger stabiliz-
ers • Lubricator support transport tray • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired quantity of .092” or .108” slickline sizes
Spooling: • Linear bar spooler systems
SC1-200 SE R I E S
4 x 4 Single Axle Slickline Crane Unit Articulating Crane with Single WL Drum
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Measure head • Electronic display meters for
line speed, depth and tension 110V AC Power: • 3,000 watt inverter AC systems Drop Spools: • Quick removable drop off drum
spool system
Cab Dimensions:
1.52.m L x 2.38m W (60 in L x 94 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 3,170 kg (7,000 lbs) Rear Axle 5,400 kg (12,000 lbs)
Winch Hoist Specification:
SA1-300 Series Drawworks; Direct drum mount single spd planetary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drop Spool Drum: .092” 6,100 M (20,000 ft)
Drum Drive Performance: Drum Speed - Up to 500 mpm (1,600 fpm)
Pulling Power- Up to 1,600 kg (3,500 lbs)
Crane Capacity: • Model 703-3S • 3 sections • Vertical reach of 9 m (29 ft.) • Horizontal reach of 7.6 m (24ft.) • Load max. outreach 300 kg
(660 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SC1-400 series is a single axle combination crane and wireline unit for slickline service work applications. This unit is designed to operate in an oilfield environment including artic, desert and tropical conditions and can be modified to perform other wireline service work applications.
Features: • Unit has the 120 series van body
design with small radius rear cor-ner body style with tarpaulin roof cover over drawworks compart-ment
• 100% aluminum operator’s con-trol cabin section
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Generous quantity of external stor-age compartments and racks
• Ergonomic design control panel • Low noise level • Rear articulating hydraulic crane • Rear hydraulic out rigger stabiliz-
ers • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired quantity of .092” or .108” slickline sizes
Spooling: • Linear bar spooler systems
SC1-400 SE R I E S
4 x 2 Single Axle Slickline Crane Unit Articulating Crane, Van Body and Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring System: • In-line measure heads or con-
ventional measure heads • Mechanical or Electronic dis-
play meters 110V AC Power: • 3000 watt inverter AC system • 6000 watt inverter AC system • 10 kw hydraulic drive generator
Van Dimensions:
4.29m L x 2.48m W (169 in L x 98 in W)
Van dimensions may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,300 kg (14,000 lbs) Rear Axle 9,530 kg (21,000 lbs)
Winch Hoist Specification:
SA1-200-D Series Drawworks; 2 Spd planetary gear box chain drive with hydraulic motor Drive System with drop spool attachment
Drum Line Capacity: Slickline Drum: .108” 7,600 M (25,000 ft) Drum Drive Performance: Drum Speed - Up to 500 mpm (1,650 fpm)
Pulling Power- Up to 4,000 kg (9,000 lbs)
Drop Spool Attachment: Independent hydraulic drive motor with quick disconnect coupling on drop spool, 3,000m of .092” line.
Crane Capacity: • Model 805-4S - 4 sections • Load max. outreach 360kg • Vertical reach of 12 m (39 ft.) • Horizontal reach of 9 m (29ft.)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SC1-700 series is a single axle combination crane and wireline unit for slickline service work applica-tions. This unit is designed to oper-ate in an oilfield environment includ-ing artic, desert and tropical condi-tions and can be modified to perform other wireline service work applica-tions.
Features: • Unit has the 160 series van body
design with stepped down en-closed roof style over drawworks with double rear doors
• 100% aluminum operator’s con-trol cabin section
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Generous quantity of external stor-age compartments and racks
• Ergonomic design control panel • Low noise level • Rear corner mount hydraulic
telescoping boom crane • Rear hydraulic out rigger stabiliz-
ers • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired quantity of .092”, .108” or .125” slickline sizes
Spooling: • Linear bar spooler systems
SC1-700 SE R I E S
4 x 2 Single Axle Slickline Crane Unit Rear Boom Crane, Van Body and Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Measure head • Electronic display meters for
line speed, depth and tension Generator: • 10 kw hydraulic drive generator Boom Crane: • Boom vertical reach 13.7m (45
ft) horizontal 11.9m (39 ft) • Crane capacity 3,600 to 250 kg
Cab Dimensions:
4.39m L x 2.48m W (173 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear Axle 9,500 kg (21,000 lbs)
Winch Hoist Specification:
SA1-310 Series Drawworks; Direct drum mount single spd planetary gear box with 2 spd hydraulic motor Drive System
Split Drum Line Capacity: Drum: .108” & .125” Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 620 mpm (2,030 fpm)
Pulling Power- Up to 2,300 kg (5,030 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SC2-600 series is a tandem axle combination crane and wireline unit for slickline service work applica-tions. This unit is designed to oper-ate in an oilfield environment includ-ing artic, desert and tropical condi-tions and can be modified to perform logging service work applications.
Features: • 600 series has integrated swivel
operator’s control cab and draw-works compartment
• 25 degrees rotating cabin and drawworks compartment
• External storage compartments • 100% aluminum operator’s con-
trol cabin section • All weather thermal insulated cabin
with all weather climate con-trolled interior
• Ergonomic design control panel • Low noise level • Rear mount hydraulic boom
crane • Rear and front out rigger cylin-
ders • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired slickline Spooling: • Linear bar spooler systems or
overhead spooling system
SC2-600 SE R I E S
6 x 4 Tandem Axle Slickline Crane Unit Rear Boom Crane and WL Swivel Cabin
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Measure head • Electronic display meters for
line speed, depth and tension Generator: • 10 kw hydraulic drive generator Boom Crane: • Boom reach depending on
crane option • 10, 12, 15, 18 & 20 Ton options
Swivel Cabin Dimensions:
3.81m L x 2.33m W (150 in L x 92 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 7,200 kg (16,000 lbs) Rear Tandem Axles 18,100 kg (40,000 lbs)
Winch Hoist Specification:
SA1-200-D Series Drawworks; Two independent drum drive sys-tems, each drum has a 2 spd plane-tary gear box chain drive with hy-draulic motor Drive System
Drum Line Capacity: Slickline Drum: .108” & .125” 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 500 mpm (1,650 fpm)
Pulling Power- Up to 4,000 kg (9,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SC2-700 series is a tandem axle combination crane and wireline unit for slickline service work applica-tions. This unit is designed to oper-ate in an oilfield environment includ-ing artic, desert and tropical condi-tions and can be modified to perform other wireline service work applica-tions.
Features: • Unit has the 160 series van body
design with stepped down en-closed roof style over drawworks with double rear doors
• 100% aluminum operator’s con-trol cabin section
• All weather thermal insulated cabin with all weather climate con-trolled interior
• Generous quantity of external stor-age compartments and racks
• Ergonomic design control panel • Low noise level • Rear corner mount hydraulic
telescoping boom crane • Rear hydraulic out rigger stabiliz-
ers • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size drum drawworks to
fit desired quantity of .092”, .108” or .125” slickline sizes
Spooling: • Linear bar spooler systems
SC2-700 SE R I E S
6 x 4 Tandem Axle Slickline Crane Unit Rear Boom Crane, Van Body and Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Measure head • Electronic display meters for
line speed, depth and tension Generator: • 10 kw hydraulic drive generator Boom Crane: • Boom vertical reach 13.7m (45
ft) horizontal 11.9m (39 ft) • Crane capacity 3,600 to 250 kg
Cab Dimensions:
5.48m L x 2.48m W (216 in L x 98 in W)
Cab configuration may vary to best fit end user’s requirements
Recommended Minimum Chassis Specifications:
Front Axle 6,530 kg (14,400 lbs) Rear axle 18,100 kg (40,000 lbs)
Winch Hoist Specification:
SA2-300 Series Drawworks; Two independent drum drive systems, each drum has a direct drum mount single spd planetary gear box with 2 spd hydraulic motor Drive System
Drum Line Capacity: Drum: .108” & .125” Line 7,600 M (25,000 ft) of ea.
Drum Drive Performance: Drum Speed - Up to 620 mpm (2,030 fpm)
Pulling Power- Up to 2,300 kg (5,030 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
DYNAWINCH INDUSTRIES LTD. 6771—84TH STREET SE, CALGARY, AB T2C 4T6
Section 3
Wireline Skid Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 3 The following series of wireline skid units are base units where modifications or design changes can be made to better fit the wireline service applications. Slickline Skid Units • SS1 - 100 Light duty 1 piece gas powered slickline skid
• SS1 - 110 Light duty 1 piece diesel powered slickline skid
• SS1 - 120 Light duty 1 piece electrical powered slickline skid
• SS1 - 200 Medium duty 1 piece slickline skid
• SS1 - 220 Medium duty 1 piece slickline skid
• SS1 - 500 1 Piece electric drive wireline survey skid for drilling rigs
• SS2 - 400 2 Piece slickline skid with enclosed cabin operator skid and power pack skid
Logging Skid Units • LS1 - 500 Electric powered single drum logging skid unit • LS2 - 400 2 Piece logging skid with enclosed cabin operator skid and power pack skid
Combination Skid Units • CS1 - 400 1 Piece combination slickline and logging skid with enclosed operator cabin
Pipeline Wireline Skid Units • KS1 - 400 1 Piece pipeline wireline skid with enclosed operator cabin
Truck Mounted Skid Units • SE1 - 200 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 300 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 320 1 Piece PTO drive truck mounted slickline skid unit
Model SS1-100 series self-contained Slickline skid unit is designed to work in markets requiring economical, portable, compact, lightweight equip-ment for wireline survey service work on land based applications. The winch hydraulic system is powered by a 13 HP gas engine providing a good range of drum speed and pull-ing power for most light duty wireline service work applications.
Features:
• Aluminum base frame all welded construction
• Single point lift • Light weight • Compact design • 13 HP gas engine power • Close-loop hydraulic system • Direct hydraulic motor drum drive • Machined steel drum • Mechanical disc brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Dual spring balanced manual
hand spooler • Minimum maintenance system • Friendly control design for opera-
tions with operator’s seat • Non Zone applications
Options:
• Weight indicator gauge and load cell
• Forklift pockets under skid • Choice of other power source;
Diesel engine.
SS1-100 SE R I E S
Light Weight Single Drum Gas Engine Power Slickline Skid Unit
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 200 mpm (650 fpm) Max Speed - Rim 360 mpm (1100 fpm) Max Pull - Core 400 kgs (900 lbs) Max Pull - Rim 225 kgs (500 lbs)
Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
0.092” 4,000 M (13,100 ft)
or equivalent metric line sizes
Skid Dimensions:
1.0m L x 1.0m W x 1.0m H (39 in L x 39 in W x 39 in H)
Skid Weight (Dry) 275 kgs (600 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SS1-100 series self-contained Slickline skid unit is designed to work in markets requiring economical, portable, compact, lightweight equip-ment for wireline survey service work on land based applications. The winch hydraulic system is powered by a 8 HP diesel engine providing a good range of drum speed and pull-ing power for most light duty wireline service work applications.
Features:
• Aluminum base frame all welded construction
• Single point lift • Light weight • Compact design • 8 HP gas engine power • Close-loop hydraulic system • Direct hydraulic motor drum drive • Machined steel drum • Mechanical disc brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Dual spring balanced manual
hand spooler • Minimum maintenance system • Friendly control design for opera-
tions with operator’s seat • Non Zone applications
Options:
• Weight indicator gauge and load cell
• Forklift pockets under skid • Choice of other power source;
Diesel engine.
SS1-110 SE RI E S
Light Weight Single Drum Diesel Engine Power Slickline Skid Unit
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 145 mpm (475 fpm) Max Speed - Rim 245 mpm (800 fpm) Max Pull - Core 400 kgs (870 lbs) Max Pull - Rim 240 kgs (525 lbs)
Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
0.092” 4,000 M (13,100 ft)
or equivalent metric line sizes
Skid Dimensions:
1.0m L x 1.0m W x 1.0m H (39 in L x 39 in W x 39 in H)
Skid Weight (Dry) 275 kgs (600 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SS1-120 series electric pow-ered Slickline skid unit is designed to work in markets requiring economi-cal, portable, compact, lightweight equipment for wireline survey service work on land based applications. The winch hydraulic system is pow-ered by a 10 HP electric motor pro-viding a good range of drum speed and pulling power for most light duty wireline service work applications. Requires external electrical power source.
Features:
• Aluminum base frame all welded construction
• Single point lift • Light weight • Compact design • 10 HP electric motor power • Close-loop hydraulic system • Direct hydraulic motor drum drive • Machined steel drum • Mechanical disc brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Dual spring balanced manual
hand spooler • Minimum maintenance system • Friendly control design for opera-
tions • None Zone applications
Options:
• Weight indicator gauge and load cell
• Forklift pockets under skid • 50 or 60 Hz power source
SS1-120 SE RI E S
Light Weight Single Drum Electric Power Slickline Skid Unit
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 125 mpm (400 fpm) Max Speed - Rim 400 mpm (1,300 fpm) Max Pull - Core 1,060 kg (2,300 lbs) Max Pull - Rim 635 kg (1,350 lbs)
Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
0.092” 4,000 M (13,000 ft)
or equivalent metric line sizes
Skid Dimensions:
1.0m L x 1.0m W x 1.0m H (39 in L x 39 in W x 39 in H)
Skid Weight (Dry) 250 kg (550 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SS1-200 series self-contained Slickline skid unit is designed to work in markets requiring economical, portable, compact, lightweight equip-ment for medium duty wireline survey service work on land based applica-tions. The winch hydraulic system is powered by a 26 HP diesel engine providing a wide range of drum speed and pulling power for all me-dium duty wireline service work appli-cations.
Features:
• Aluminum frame all welded con-struction
• Four point lift • Light weight • Compact design • 26 HP diesel power engine • Close-loop hydraulic system • Direct hydraulic motor drum drive • Machined steel drum • Mechanical disc brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Linear bar hand spooler • Minimum maintenance system • Friendly control design for opera-
tions • Non Zone applications
Options:
• Weight indicator gauge and load cell
• Heli-portable • Forklift pockets under skid • Quick removable drum spool op-
tion
SS1-200 SE R I E S
Medium Duty Single Drum Diesel Engine Power Slickline Skid Unit
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 274 mpm (900 fpm) Max Speed - Rim 400 mpm (1,300 fpm) Max Pull - Core 1,100 kg (2,400 lbs) Max Pull - Rim 750 kg (1,650 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity: 0.092” 4,000 M (15,000 ft) 0.108” 3,500 M (11,500 ft)
Skid Dimensions:
1.5m L x 1.2m W (60 in L x 48 in W)
Skid Weight (Dry) 600 kgs
(1,350 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SS1-220 series electric power Slickline skid unit is designed to work in markets requiring economical, portable, compact, lightweight equip-ment for light to medium duty wireline service work on land based applica-tions, requires external electric power source to drive motor. The winch hydraulic system is powered by a 15 HP electric motor providing a wide range of drum speed and pulling power for all light to medium duty wireline service work applications.
Features:
• Aluminum frame all welded con-struction
• Light weight • Compact design • 15 HP electric motor • Close-loop hydraulic system • Direct hydraulic motor drum drive • Machined steel drum • Mechanical disc brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Linear bar hand spooler • Weight indicator gauge and load
cell • Minimum maintenance system • Friendly control design for opera-
tions • Forklift access from front or rear • Non Zone applications
Options:
• Electronic measure system • Crash cage and lifting system • Non-II certified
SS1-220 SE R I E S
Medium Duty Single Drum Electric Power Slickline Skid Unit
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 329 mpm (1070 fpm) Max Speed - Rim 540 mpm (1,770 fpm) Max Pull - Core 700 kg (1,540 lbs) Max Pull - Rim 545 kg (1,200 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity: 0.092” 7,600 M (25,000 ft) 0.108” 5,400 M (18,000 ft)
Skid Dimensions:
1.85m L x 1.06m W (72 in L x 42 in W)
Skid Weight (Dry) 715 kg
(1,575 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised Oct 06
Model SS1-500 series Zone I classifi-cation electric powered Slickline Sur-vey skid unit is designed to work on a drilling rig floor on land or off-shore applications. The winch hydraulic system is powered by a 20 HP elec-tric motor providing a wide range of drum speed and pulling power for all wireline survey service work applica-tions. Requires external electrical power source.
Features:
• Steel base frame all welded con-struction
• Single point lift • Compact design • 20 HP electric motor power • Close-loop hydraulic system • Transmission drum drive • Machined steel drum • Mechanical band brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Dual spring balanced manual
hand spooler • Minimum maintenance system • Friendly control design for opera-
tions
Options:
• Weight indicator gauge and load cell
• Forklift pockets under skid • 50 or 60 Hz power source
• Planetary drum drive
• Zone I applications
SS1-500 SE RI E S
Slickline Single Drum Survey Skid Unit Zone I Electric Power
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 125 mpm (400 fpm) Max Speed - Rim 400 mpm (1,300 fpm) Max Pull - Core 1,060 kg (2,300 lbs) Max Pull - Rim 635 kg (1,350 lbs)
Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
0.092” 7,600 M (25,000 ft) 0.108” 6,100 M (20,000 ft)
or equivalent metric line sizes
Skid Dimensions:
1.1m L x .92m W x 1.3m H (42 in L x 36 in W x 50 in H)
Skid Weight (Dry) 750 kg (1,650 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SS2-400 series 2 piece Slick-line skid package unit is designed to work in markets requiring portable, compact, lightweight equipment for slickline service work applications. The 45 hp diesel power pack skid provides the hydraulic winch skid with a wide range of drum speed and pulling power for wireline service work applications.
Features:
• Aluminum frame all welded con-struction
• Integral enclosed operator cabin • Four point lifting slings • Integral forklift pockets • Light weight • Compact design • 45 HP diesel power pack • Close-loop hydraulic system • Direct drum planetary drive sys-
tem • Machined steel drum • Mechanical band brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Linear bar hand spooler • Minimum maintenance system • Friendly control design for opera-
tions
Options:
• Weight indicator gauge and load cell
• Electronic measuring system • Heli-portable • Zone II specifications
SS2-400 SE R I E S
Slickline Single Drum with Control Cab Skid with Diesel Engine Power Pack Skid
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 200 mpm (660 fpm) Max Speed - Rim 550 mpm (1,800 fpm) Max Pull - Core 1,500 kg (3,500 lbs) Max Pull - Rim 860 kg (1,950 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Drum Configuration can accommo-date 7,500m (25,000 ft) of following slickline
0.092” - 0.108” - 0.125”
Skid Dimensions: Control Skid 2.0m L x 1.65m W (80 in L x 65 in W) Dry Weight 900 kg (2,000 lbs)
Power Skid 2.0m L x .92m W (80 in L x 36 in W) Dry Weight 800 kg (1,750 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Wireline Skid Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 3 The following series of wireline skid units are base units where modifications or design changes can be made to better fit the wireline service applications. Slickline Skid Units • SS1 - 100 Light duty 1 piece gas powered slickline skid
• SS1 - 110 Light duty 1 piece diesel powered slickline skid
• SS1 - 120 Light duty 1 piece electrical powered slickline skid
• SS1 - 200 Medium duty 1 piece slickline skid
• SS1 - 220 Medium duty 1 piece slickline skid
• SS1 - 500 1 Piece electric drive wireline survey skid for drilling rigs
• SS2 - 400 2 Piece slickline skid with enclosed cabin operator skid and power pack skid
Logging Skid Units • LS1 - 500 Electric powered single drum logging skid unit • LS2 - 400 2 Piece logging skid with enclosed cabin operator skid and power pack skid
Combination Skid Units • CS1 - 400 1 Piece combination slickline and logging skid with enclosed operator cabin
Pipeline Wireline Skid Units • KS1 - 400 1 Piece pipeline wireline skid with enclosed operator cabin
Truck Mounted Skid Units • SE1 - 200 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 300 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 320 1 Piece PTO drive truck mounted slickline skid unit
Model SS1-500 series Zone I classifi-cation electric powered Logging skid unit is designed to work on a drilling rig floor on land or off-shore applica-tions. The winch hydraulic system is powered by a 30 HP electric motor providing a wide range of drum speed and pulling power for all wire-line logging service work applica-tions. Requires external electrical power source.
Features:
• Steel base frame all welded con-struction
• Four point lift • Compact design • 30 HP electric motor power • Close-loop hydraulic system • 4 spd Transmission drum drive • Machined steel drum • Mechanical band brake • Prepped, primed and painted • Measuring head • Depth mechanical counter • Front dual bar mechanical hand
spooler system • Minimum maintenance system • Friendly control design for opera-
tions
Options:
• Weight indicator gauge and load cell
• Forklift pockets under skid • 50 or 60 Hz power source
• Planetary drum drive
• Zone I applications
LS1-500 SE RI E S
Logging Single Drum Skid Unit Zone I Electric Power
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 190 mpm (620 fpm) Max Speed - Rim 430 mpm (1,410 fpm) Max Pull - Core 2200 kg (4,900 lbs) Max Pull - Rim 1,100 kg (2,400 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Typical drum design can hold Up to 5,200 M (16,000 ft) of
7/32” Braided Line or
Skid Dimensions: Logger Skid 1.52m L x 1.27m W (60 in L x 50 in W)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LS2-400 series 2 piece Log-ging skid package unit is designed to work in markets requiring portable, compact equipment for logging ser-vice work applications. The 80 hp diesel power pack skid provides the hydraulic winch skid with a wide range of drum speed and pulling power for all case or open hole log-ging service work applications and provides climate controlled operator’s cabin.
Features:
• Aluminum frame all welded con-struction
• Integral enclosed operator cabin • Climate control operator cabin • Four point lifting slings • Integral forklift pockets • Light weight • Compact design • 80 HP diesel power pack • Close-loop hydraulic system • Machined steel drum • Air activated band brake • Prepped, primed and painted • Minimum maintenance system • Friendly control design for opera-
tions
Options:
• Measure head • Weight indicator gauge and load
cell • Electronic measuring system • Spooler system • Heli-portable • Zone II specifications
LS2-400 SE RI E S
Logging Single Drum with Control Cab Skid and Diesel Engine Power Pack Skid
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 180 mpm (370 fpm) Max Speed - Rim 430 mpm (880 fpm) Max Pull - Core 12,000 kg (26,000 lbs) Max Pull - Rim 7,000 kg (15,400 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” - 1/4” - 5/16” Braided Line or 15/32” Multi-Conductor
or equivalent metric line sizes
Skid Dimensions: Control Skid 3.8m L x 2.2m W (150 in L x 87 in W)
Power Skid 2.7m L x 1.2m W (108 in L x 48 in W)
DYNAWINCH INDUSTRIES LTD. 6771—84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Wireline Skid Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 3 The following series of wireline skid units are base units where modifications or design changes can be made to better fit the wireline service applications. Slickline Skid Units • SS1 - 100 Light duty 1 piece gas powered slickline skid
• SS1 - 110 Light duty 1 piece diesel powered slickline skid
• SS1 - 120 Light duty 1 piece electrical powered slickline skid
• SS1 - 200 Medium duty 1 piece slickline skid
• SS1 - 220 Medium duty 1 piece slickline skid
• SS1 - 500 1 Piece electric drive wireline survey skid for drilling rigs
• SS2 - 400 2 Piece slickline skid with enclosed cabin operator skid and power pack skid
Logging Skid Units • LS1 - 500 Electric powered single drum logging skid unit • LS2 - 400 2 Piece logging skid with enclosed cabin operator skid and power pack skid
Combination Skid Units • CS1 - 400 1 Piece combination slickline and logging skid with enclosed operator cabin
Pipeline Wireline Skid Units • KS1 - 400 1 Piece pipeline wireline skid with enclosed operator cabin
Truck Mounted Skid Units • SE1 - 200 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 300 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 320 1 Piece PTO drive truck mounted slickline skid unit
Model CS1-400 series 1 piece Com-bination skid unit is designed to work in markets requiring portable equip-ment for slickline and logging service work applications. The skid is de-signed to operate in harsh environ-ments and can withstand severe transport handling conditions. The 110 hp diesel engine provides hy-draulic power to the winch drums and to the hydraulic generator which pro-vides the operator’s cabin with a cli-mate controlled environment. The winch drums can be designed with any combination of line for slickline, swabbing and logging service work applications.
Features:
• Steel frame all welded construc-tion
• Enclosed climate control opera-tor cabin
• Four point lifting slings • Integral forklift pockets • 1 piece self contained skid • 110 HP diesel power pack • Close-loop hydraulic system • Dual drum drawworks winch • Prepped, primed and painted • Minimum maintenance system • Friendly control design for opera-
tions
Options:
• Measure head • Weight indicator gauge and load
cell • Electronic measuring system • Spooler system • Hydraulic generator
CS1-400 SE R I E S
Double Drum Combination Skid with Control Cabin and Diesel Power Pack
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Braided Drum Winch Hoist Specification:
Max Speed - Core 180 mpm (370 fpm) Max Speed - Rim 430 mpm (880 fpm) Max Pull - Core 12,000 kg (26,000 lbs) Max Pull - Rim 7,000 kg (15,400 lbs)
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” - 1/4” - 5/16” Braided Line or equivalent metric line sizes
Slickline Drum Winch Hoist Specification:
Max Speed - Core 420 mpm (1,400 fpm) Max Speed - Rim 600 mpm (2,000 fpm) Max Pull - Core 1,9500kg (4,300 lbs) Max Pull - Rim 1,350 kg (3,000 lbs)
Typical drum design can hold Up to 7,600 M (25,000 ft) of
.092” - .108” - .125” Line Skid Dimensions:
5.3m (210 in) L x 2.4m (94 in) W
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Wireline Skid Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 3 The following series of wireline skid units are base units where modifications or design changes can be made to better fit the wireline service applications. Slickline Skid Units • SS1 - 100 Light duty 1 piece gas powered slickline skid
• SS1 - 110 Light duty 1 piece diesel powered slickline skid
• SS1 - 120 Light duty 1 piece electrical powered slickline skid
• SS1 - 200 Medium duty 1 piece slickline skid
• SS1 - 220 Medium duty 1 piece slickline skid
• SS1 - 500 1 Piece electric drive wireline survey skid for drilling rigs
• SS2 - 400 2 Piece slickline skid with enclosed cabin operator skid and power pack skid
Logging Skid Units • LS1 - 500 Electric powered single drum logging skid unit • LS2 - 400 2 Piece logging skid with enclosed cabin operator skid and power pack skid
Combination Skid Units • CS1 - 400 1 Piece combination slickline and logging skid with enclosed operator cabin
Pipeline Wireline Skid Units • KS1 - 400 1 Piece pipeline wireline skid with enclosed operator cabin
Truck Mounted Skid Units • SE1 - 200 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 300 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 320 1 Piece PTO drive truck mounted slickline skid unit
Model KS1-400 series HD pipeline wireline skid unit designed to work in markets requiring portable equipment for pipeline service work applications. The skid is designed to operate in harsh environments and can with-stand severe transport handling con-ditions. The design allows the skid to be packed inside a 20 ft shipping container. The 110 hp diesel engine provides hydraulic power to the winch drum and spooler system. The skid comes with control cab with con-trol panel, captain’s chair, bench seat and storage cabinets. The HD draw-works winch assembly design specifi-cally for heavy line pull service appli-cations.
Features:
• Steel frame all welded construc-tion
• Enclosed climate control opera-tor cabin
• Four point lifting slings • Integral forklift pockets • 1 piece self contained skid • 110 HP diesel power pack • Close-loop hydraulic system • HD drawworks winch • Prepped, primed and painted • Minimum maintenance design • Friendly control design for opera-
tions • HD measure head, 30,000 lb
rated capacity • Electronic measuring system
Options:
• 10kw Hydraulic generator • Cab Air conditioning
KS1-400 SE R I E S
HD Pipeline Wireline Skid with Control Cabin and Diesel Power Pack
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Skid Dimension:
Length: 5.33m (210 in) Width: 2.14m (84 in) Height: 2.18m (86 in)
Operator Cab Dimensions:
Length: 1.55m (61 in) Width: 1.85m (73 in) Dry Weight: 7,500 kg (16,500 lb)
Winch Hoist Specification: Max Speed - Core 140 mpm (450 fpm) Max Speed - Rim 300 mpm (984 fpm) Max Pull - Core 18,600 kg (41,000 lbs) Max Pull - Rim 8,800 kg (19,400 lbs)
Typical drum design can hold Up to 3,000 M (10,000 ft) of
1/2” Cable
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised July 06
Wireline Skid Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 3 The following series of wireline skid units are base units where modifications or design changes can be made to better fit the wireline service applications. Slickline Skid Units • SS1 - 100 Light duty 1 piece gas powered slickline skid
• SS1 - 110 Light duty 1 piece diesel powered slickline skid
• SS1 - 120 Light duty 1 piece electrical powered slickline skid
• SS1 - 200 Medium duty 1 piece slickline skid
• SS1 - 220 Medium duty 1 piece slickline skid
• SS1 - 500 1 Piece electric drive wireline survey skid for drilling rigs
• SS2 - 400 2 Piece slickline skid with enclosed cabin operator skid and power pack skid
Logging Skid Units • LS1 - 500 Electric powered single drum logging skid unit • LS2 - 400 2 Piece logging skid with enclosed cabin operator skid and power pack skid
Combination Skid Units • CS1 - 400 1 Piece combination slickline and logging skid with enclosed operator cabin
Pipeline Wireline Skid Units • KS1 - 400 1 Piece pipeline wireline skid with enclosed operator cabin
Truck Mounted Skid Units • SE1 - 200 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 300 1 Piece PTO drive truck mounted slickline skid unit
• SE1 - 320 1 Piece PTO drive truck mounted slickline skid unit
Model SE1-200 series truck mounted self-contained Slickline skid unit, de-signed to work in markets requiring economical equipment for medium duty wireline service work on land based applications. The winch hy-draulic system is powered by the truck PTO system offering a wide range of drum speed and pulling power for all medium duty wireline service work applications.
Features:
• Modular steel skid design, can be removed from truck deck
• Below deck external storage available on truck deck
• Work vise mounted on truck deck • Truck PTO power supply for hy-
draulic system • Skid dash panel truck engine
remote engine throttle • Operator dash panel controls • Operator adjustable seat • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired .092” or .108” slickline line sizes
Spooling: • Linear bar spooler systems
SE1-200 SE RI E S
Slickline Truck Mounted Skid Unit Single Drum Drawworks with Re-spooler
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Measuring: • Measure head • Mechanical depth and tension
system Re-Spooler Attachment: • Self spooler drive attachment
Deck Dimensions:
3.30.m L x 2.38m W (130 in L x 94 in W)
Recommended Minimum Chassis Specifications:
Front Axle 3,170 kg (7,000 lbs) Rear Axle 5,400 kg (12,000 lbs)
Winch Hoist Specification:
SA1-200 Series Drawworks; 2 Spd planetary gear box chain drive with hydraulic motor Drive System with drop spool attachment
Drum Line Capacity: Slickline Drum: .092” 7,600 M (25,000 ft)
Drum Drive Performance: Drum Speed - Up to 500 mpm (1,650 fpm)
Pulling Power- Up to 4,000 kg (9,000 lbs)
Additional drum drive system op-tions available to best meet specific service work applications.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SE1-300 series truck mounted self-contained Slickline skid unit, de-signed to work in markets requiring economical equipment for medium duty wireline survey service work on land based applications. The winch hydraulic system is powered by the truck PTO system offering a wide range of drum speed and pulling power for all medium duty wireline service work applications.
Features:
• Compact skid design • All operator controls on the side
of skid • Truck PTO power supply for hy-
draulic system • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired .092” or .108” slickline line sizes
Spooling: • Mechanical dual spring balance
manual hand spooler
SE1-300 SE RI E S
Slickline Truck Mounted Skid Unit Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 274 mpm (900 fpm) Max Speed - Rim 400 mpm (1,300 fpm) Max Pull - Core 1,100 kg (2,400 lbs) Max Pull - Rim 750 kg (1,650 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity: 0.092” 4,000 M (15,000 ft) 0.108” 3,500 M (11,500 ft)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SE1-320 series truck mounted self-contained Slickline skid unit, de-signed to work in markets requiring economical equipment for medium duty wireline service work on land based applications. The winch hy-draulic system is powered by the truck PTO system offering a wide range of drum speed and pulling power for all medium duty wireline service work applications.
Features:
• Modular steel skid design, can be removed from truck deck
• Below deck external storage available on truck deck
• Work vise mounted on truck deck • Truck PTO power supply for hy-
draulic system • Skid dash panel truck engine
remote engine throttle • Operator dash panel controls • Prepped, primed and painted Hydraulic System: • HD close-loop hydraulic system • Minimum maintenance design
systems • Friendly control design for opera-
tions • Installed on truck chassis or sent
out as a field installation package
Wireline Accessories Options:
Drawworks: • Multiple size double drum draw-
works to fit desired .092” or .108” slickline line sizes
Spooling: • Linear bar spooler systems
SE1-320 SE RI E S
Slickline Truck Mounted Skid Unit Single Drum Drawworks
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 274 mpm (900 fpm) Max Speed - Rim 400 mpm (1,300 fpm) Max Pull - Core 1,100 kg (2,400 lbs) Max Pull - Rim 750 kg (1,650 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity: 0.092” 4,000 M (15,000 ft) 0.108” 3,500 M (11,500 ft)
Skid Dimensions:
1.5m L x 1.5m W (60 in L x 60 in W)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84TH STREET SE, CALGARY, AB T2C 4T6
Section 4
Drawworks Winch Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 4 The following series of drawworks winch equipment are base units where modifications or design changes can be made to better fit the wireline service applications.
Slickline Drawworks Winch Units • SA1 - 110 Single split drum with 4spd transmission chain drive
• SA1 - 110-D Single split drum with 4spd transmission chain drive and drop spool attachment
• SA1 - 200-D Single drum with 2spd planetary chain drive and drop spool attachment
• SA1 - 210 Single split drum with 2spd planetary chain drive
• SA1 - 300 Light Duty single drum with direct mount planetary drive
• SA1 - 320 Medium duty single drum with direct mount planetary drive
• SA1 - 500 Light duty drop spool winch system with direct drive motor
• SA1 - 520 Medium duty drop spool winch system with 2spd planetary chain drive
• SA1 - 550 Single drum re-spooler winch system with direct drive rotary motor
Logging Drawworks Winch Units • LA1 - 100 Single drum with 3spd transmission drive
• LA1 - 200 Single drum with planetary chain drive
• LA1 - 310 Single split drum with direct mount planetary drive
• LA1 - 400 Single drum with 2spd direct mount planetary drive
• LA1 - 400SS Stainless steel single drum with 2spd direct mount planetary drive
• LA1 - 410 Single split drum with 2spd direct mount planetary drive
• LA2 - 300 Double drum with two direct mount planetary drive systems
• LA2 - 400 Double drum with two 2spd direct mount planetary drive systems
Combination Drawworks Winch Units • CA2 - 615 Double drum with planetary drive on slickline drum and 3spd transmission on braided drum
• CA2 - 720 Double drum with transmission drive on slickline drum and planetary drive on braided drum
• CA2 - 840 Double drum with two direct mount planetary drive systems
Model SA1-110 series drawworks winch assembly is a single split drum hydraulic winch designed for heavy duty slickline service work applications for line size 0.108” and larger. Available in single line or split drum configuration. The 4 speed manual transmission hydrau-lic drive system offers a wide range of line speeds and line pulling power making this unit ideal for jar-ring and HD fishing operations, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 4 Speed manual transmission with direct mount hydraulic mo-tor
• Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with me-
chanical and air operated con-trols
• HD drum shaft bearings • Split or non split drum configu-
rations • Aluminum chain guards • Prepped, primed and painted • Minimum maintenance system
Options: • Linear double bar spooler sys-
tem • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-110 SE R I E S WI NC H
Single Split Drum Slickline Winch 4 Speed Transmission Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 518 mpm (1,700 fpm) Max Speed - Rim 750 mpm (2,450 fpm) Max Pull - Core 4,300 kg (9,500 lbs) Max Pull - Rim 3,100 kg ( 7,000 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Split Drum Configuration can ac-commodate any one of the following line configuration, customer choice of drum line capacity
0.108” / 0.125” 0.108” / 0.140” 0.125” / 0.125” 0.125” / 01.40”
Optional Core Diameter:
For slickline sizes of 0.150”, 0.160” and 0.187”
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-110-D series drawworks winch assembly is a single split drum hydraulic winch with a drop spool attachment. The main drum designed for heavy duty slickline service work applications for line size 0.108” and larger. The quick removable drop spool attachment for special recorder and memory gauge service work. The 4 speed manual transmission hydraulic drive system offers a wide range of line speeds and line pulling power mak-ing this unit ideal for jarring and HD fishing operations, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 4 Speed manual transmission with direct mount hydraulic motor
• Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with me-
chanical and air operated con-trols
• HD drum shaft bearings • Split or non split drum configu-
rations • Aluminum chain guards • Prepped, primed and painted • Minimum maintenance system
Options: • Linear double bar spooler sys-
tem • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-110-D SE R I E S WI NC H
Drop Spool & Split Drum Slickline Winch 4 Speed Transmission Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 518 mpm (1,700 fpm) Max Speed - Rim 750 mpm (2,450 fpm) Max Pull - Core 4,300 kg (9,500 lbs) Max Pull - Rim 3,100 kg ( 7,000 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Split Drum Configuration can ac-commodate any one of the following line configuration, customer choice of drum line capacity
0.108” / 0.125” 0.108” / 0.140” 0.125” / 0.125” 0.125” / 01.40”
Drop Spool:
0.092” 3,000m
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-200-D series drawworks winch assembly is a single drum hydraulic winch with a drop spool attachment. The main drum de-signed for slickline service work applications for line size up to 0.108”. The quick removable drop spool attachment for special re-corder and memory gauge service work. The 2 speed electric shift planetary gear box with direct mount hydraulic motor chain drive system offers a wide range of line speeds and line pulling power suit-able for a wide variety of slickline service work operations, winch de-signs for mobile skid units and for land based truck mounted applica-tions.
Features:
• High performance with a wide range of line pulling and line speeds
• 2 Speed electric shift planetary gear box with direct mount hydraulic motor
• Close-loop hydraulic system • Machined balanced steel drum • Single or dual band brakes with
mechanical operated control • HD drum shaft bearings • Split or non-split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options:
• Linear double bar spooler sys-tem
• Weight indicator gauge and load cell
• Measure heads
SA1-200-D SE R I E S WI NC H
Drop Spool & Single Drum Slickline Winch 2 Speed Planetary Chain Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 285 mpm (985 fpm) Max Speed - Rim 500 mpm (1,650 fpm) Max Pull - Core 4,000 kg (9,000 lbs) Max Pull - Rim 2,400 kg (5,300 lbs)
Drum Line Capacity: Drum Configuration can accommo-date any of the following line con-figurations
Typical drum can hold 7,600 M (25,000 ft) of
0.092” or 0.108”
Split drum design can hold 6,100 M each split of
0.092” / 0.092” 0.092” / 0.108”
Or equivalent metric line sizes
Drop Spool:
0.092” 3,000m
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-210 series drawworks winch assembly is a single split drum hydraulic winch designed for medium duty slickline service work applications for line size up to 0.108”. Available in single line or split drum configuration. The 2 speed electric shift planetary gear box with direct mount hydraulic mo-tor chain drive system offers a wide range of line speeds and line pulling power suitable for a wide variety of slickline service work operations, winch designs for mobile skid units and for land based truck mounted applications.
Features:
• High performance with a wide range of line pulling and line speeds
• 2 Speed electric shift planetary gear box with direct mount hydraulic motor
• Close-loop hydraulic system • Machined balanced steel drum • Single or dual band brakes with
mechanical operated control • HD drum shaft bearings • Split or non-split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options:
• Linear double bar spooler sys-tem
• Weight indicator gauge and load cell
• Measure heads • Electronic measuring system • Air operated band brakes
SA1-210 SE RI E S WI NC H
Single Split Drum Slickline Winch 2 Speed Planetary Chain Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 285 mpm (985 fpm) Max Speed - Rim 500 mpm (1,650 fpm) Max Pull - Core 4,000 kg (9,000 lbs) Max Pull - Rim 2,400 kg (5,300 lbs)
Drum Line Capacity: Drum Configuration can accommo-date any of the following line con-figurations
Typical drum can hold 7,600 M (25,000 ft) of
0.092” or 0.108”
Split drum design can hold 6,100 M each split of
0.092” / 0.092” 0.092” / 0.108”
Or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-300 Series drawworks winch assembly is a light duty single drum hydraulic winch designed for light duty slickline applications for line size up to 0.092”. The dive sys-tem consist of single speed direct mount planetary gear box with di-rect mount hydraulic motor that eliminate the chain drive. It offers a range of line speeds and line pulling power suitable for retrieving survey tools, memory gauge work and for various other light duty slickline op-erations, winch designs for mobile skid units and for land based truck mounted applications.
Features:
• Direct mount planetary gear box drive with direct mount hydrau-lic motor
• Open-loop hydraulic system • Compact design • Machined balanced steel drum • Single band brake with me-
chanical operated control • HD drum shaft bearing • No chain drive • Prepped, primed and painted • Minimum maintenance system Options:
• Spooler system • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-300 SE RI E S WI N C H
Light Duty Single Drum Slickline Winch Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 100 mpm (325 fpm) Max Speed - Rim 300 mpm (985 fpm) Max Pull - Core 550 kg (1,200 lbs) Max Pull - Rim 500 kg (900 lbs)
Drum Line Capacity: Drum Configuration can accommo-date 6,100 M (20,000 ft) 0.092” slickline.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-320 Series drawworks winch assembly is a medium duty single drum hydraulic winch de-signed for slickline applications for line size up to 0.108”. The drive system consist of single speed di-rect mount planetary gear box with a 2 speed direct mount hydraulic motor that eliminate the chain drive. It offers a range of line speeds and line pulling power suitable for re-trieving survey tools, memory gauge work and for various other slickline operations, winch designs for mo-bile skid units and for land based truck mounted applications.
Features:
• Direct mount planetary gear box drive with direct mount hydrau-lic motor
• Close-loop hydraulic system • Compact design • Machined balanced steel drum • Single band brake with me-
chanical operated control • HD drum shaft bearing • No chain drive • Prepped, primed and painted • Minimum maintenance system Options:
• Spooler system • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-320 SE RI E S WI N C H
Medium Duty Single Drum Slickline Winch Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 195 mpm (640 fpm) Max Speed - Rim 580 mpm (1,900 fpm) Max Pull - Core 1,650 kg (3,590 lbs) Max Pull - Rim 1,150 kg (2,500 lbs)
Drum Line Capacity: Drum Configuration can accommo-date 7,600 M (25,000 ft) 0.092” or .108” slickline.
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-500 series drawworks “Drop Spool” winch assembly is a single removable drum hydraulic winch designed for light duty slick-line service work applications for .092” line size. The spool comes with quick disconnect coupler to hydraulic motor, drive coupling c/w disc brake flange. The hydraulic motor drive system offers a good range of line speeds and line pulling power suitable for retrieving survey tools, memory gauge work and for various of other light duty slickline service work applications. The main feature is the ability to remove the drum spool quickly and insert another drum in only minutes, winch designs for mobile skid units and for land based truck mounted applica-tions.
Features: • Direct drive hydraulic motor • Quick disconnect coupler • Compact design • Machined balanced steel drum • Quick removable drum system • Disc brake with mechanical or
hydraulic control • HD drum shaft bearing • Prepped, primed and painted • Minimum maintenance system
Options: • Spooler system • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-500 SE RI E S WI N C H
Drop Spool Slickline Winch Hydraulic Motor Direct Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 200 mpm (650 fpm) Max Speed - Rim 395 mpm (1,250 fpm) Max Pull - Core 630 kg (1,350 lbs) Max Pull - Rim 325 kg (700 lbs)
Drum Line Capacity:
Typical drop drum spool design can hold
3,000 M (10,000 ft) of .092”
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-520 series drawworks winch assembly is a removable sin-gle drum hydraulic winch designed for medium duty slickline service work applications for line size up to 0.108”. The 2 speed electric shift planetary gear box with direct mount hydraulic motor chain drive system offers a wide range of line speeds and line pulling power suit-able for retrieving survey tools, memory gauge work and for various of other medium duty slickline ser-vice work applications. One main feature is the ability to remove the drum spool quickly and insert an-other drum spool in only minutes, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 2 Speed electric shift planetary gear box with direct mount hydraulic motor
• Compact design • Machined balanced steel drum • Quick removable drum system • Disc brake with mechanical or
hydraulic control • HD drum shaft bearing • Aluminum chain guards • Prepped, primed and painted • Minimum maintenance system
Options: • Spooler system • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-520 SE RI E S WI N C H
Drop Spool Slickline Winch 2 Speed Planetary Chain Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 285 mpm (985 fpm) Max Speed - Rim 500 mpm (1,650 fpm) Max Pull - Core 2,400 kg (5,200 lbs) Max Pull - Rim 1,700 kg (3,700 lbs)
Drum Line Capacity:
Typical drop drum spool design can hold
3,000 M (10,000 ft) of .092” or .108”
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model SA1-550 series drawworks winch assembly is a removable sin-gle drum hydraulic winch designed for medium duty slickline service work applications for line size up to 0.108”. The drum spool can be re-moved and a regular steel line spool can be installed to spool line onto another winch unit or can be used as a re-spooler to remove line from another winch unit. The direct drive Rotary motor with quick disconnect coupler offers a range of line speeds and line pulling power suit-able for retrieving survey tools, memory gauge work and for various of other light duty slickline service work applications. One main fea-ture is the ability to remove the drum spool quickly and install an-other drum or a line spool in only minutes, winch designs for mobile skid units and for land based truck mounted applications.
Features: • Direct drive hydraulic motor • Compact design • Machined balanced steel drum • Quick removable drum system • Disc brake with mechanical or
hydraulic control • HD drum shaft bearing • Aluminum chain guards • Prepped, primed and painted • Minimum maintenance system
Options: • Spooler system • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
SA1-550 SE RI E S WI N C H
Re-Spooler Single Drum Slickline Winch Direct Drive Rotary Motor
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 140 mpm (460 fpm) Max Speed - Rim 275 mpm (900 fpm) Max Pull - Core 800 kg (1,700 lbs) Max Pull - Rim 1,600 kg (3,500 lbs)
Drum Line Capacity:
Typical drop drum spool design can hold
7,600 M (25,000 ft) of .092” or .108”
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Drawworks Winch Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 4 The following series of drawworks winch equipment are base units where modifications or design changes can be made to better fit the wireline service applications.
Slickline Drawworks Winch Units • SA1 - 110 Single split drum with 4spd transmission chain drive
• SA1 - 110-D Single split drum with 4spd transmission chain drive and drop spool attachment
• SA1 - 200-D Single drum with 2spd planetary chain drive and drop spool attachment
• SA1 - 210 Single split drum with 2spd planetary chain drive
• SA1 - 300 Light Duty single drum with direct mount planetary drive
• SA1 - 320 Medium duty single drum with direct mount planetary drive
• SA1 - 500 Light duty drop spool winch system with direct drive motor
• SA1 - 520 Medium duty drop spool winch system with 2spd planetary chain drive
• SA1 - 550 Single drum re-spooler winch system with direct drive rotary motor
Logging Drawworks Winch Units • LA1 - 100 Single drum with 3spd transmission drive
• LA1 - 200 Single drum with planetary chain drive
• LA1 - 310 Single split drum with direct mount planetary drive
• LA1 - 400 Single drum with 2spd direct mount planetary drive
• LA1 - 400SS Stainless steel single drum with 2spd direct mount planetary drive
• LA1 - 410 Single split drum with 2spd direct mount planetary drive
• LA2 - 300 Double drum with two direct mount planetary drive systems
• LA2 - 400 Double drum with two 2spd direct mount planetary drive systems
Combination Drawworks Winch Units • CA2 - 615 Double drum with planetary drive on slickline drum and 3spd transmission on braided drum
• CA2 - 720 Double drum with transmission drive on slickline drum and planetary drive on braided drum
• CA2 - 840 Double drum with two direct mount planetary drive systems
Model LA1-100 series drawworks winch assembly is a single drum hydraulic winch designed for heavy duty logging service work applica-tions. Available in single line or split drum configuration. The 3 speed manual transmission hydraulic drive system offers a wide range of line speeds and line pulling power suit-able for heavy logging service work in case hole and or open hole op-erations, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 3 speed manual transmission gear box with direct mount 2 speed hydraulic motor
• Electric over air shift selector • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearings • Split or non split drum configu-
rations • Drive system aluminum guards • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA1-100 SE R I E S WI NC H
Single Drum Logging Winch 3 Speed Transmission Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 180 mpm (370 fpm) Max Speed - Rim 430 mpm (880 fpm) Max Pull - Core 12,000 kg (26,000 lbs) Max Pull - Rim 7,000 kg (15,400 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or 3/8” Braided Line or
15/32” Multi-Conductor
Series 110 Split drum design 6,100 M of 7/32” (20,000 ft) 6,700 M of 5/16” (22,000 ft)
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA1-200 series drawworks winch assembly is a single drum hydraulic winch designed for heavy duty logging service work applica-tions. Available in single line or split drum configuration. The drum chain drive to the single speed planetary gear box with direct mount 2 speed hydraulic motor drive system offers a wide range of line speeds and line pulling power suitable for heavy logging service work in case hole and or open hole operations, winch designs for mobile skid units and for land based truck mounted applica-tions.
Features: • High performance with a wide
range of line pulling and line speeds
• Planetary gear box with direct mount 2 speed hydraulic motor
• Electric shift motor speed • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA1-200 SE R I E S WI NC H
Single Drum Logging Winch Planetary Chain Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 415 mpm (1,360 fpm) Max Pull - Core 9,000 kg (19,800 lbs) Max Pull - Rim 3,400 kg (7,500 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or 3/8” Braided Line or
15/32” Multi-Conductor
Split drum design can hold 6,100 M of 7/32” (20,000 ft) 7,000 M of 5/16” (23,000 ft)
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA1-310 series drawworks winch assembly is a single split drum hydraulic winch designed for perforating logging service work applications. Available in single line or split drum configuration. The direct mount single speed planetary gear box with direct mount 2 speed hydraulic motor drive system offers a wide range of line speeds and line pulling power suitable for logging service work in case hole opera-tions, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• Direct mount planetary gear box with direct mount 2 speed hy-draulic motor
• Electric motor shift • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA1-310 SE R I E S WI NC H
Single Split Drum Logging Winch Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 470 mpm (1,540 fpm) Max Pull - Core 3,100 kg (8,800 lbs) Max Pull - Rim 1,800 kg (4,000 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or
Split drum design can hold 4,000 M of 7/32” (13,000 ft) 5,000 M of 5/16” (16,000 ft)
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA1-400 series drawworks winch assembly is a single drum hydraulic winch designed for heavy duty logging service work applica-tions. Available in single line or split drum configuration. The 2 speed electric over hydraulic shift plane-tary gear box with direct mount 2 speed hydraulic motor drive system offers a wide range of line speeds and line pulling power suitable for heavy logging service work in case hole and or open hole operations, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 2 speed planetary gear box with direct mount 2 speed hydraulic motor
• Electric shift selector • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA1-400 SE R I E S WI NC H
Single Drum Logging Winch 2 Speed Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 415 mpm (1,360 fpm) Max Pull - Core 15,000 kg (33,000 lbs) Max Pull - Rim 6,100 kg (13,420 lbs) Drive specifications can be adjusted to best fit service applications. Speeds as low a 1 mpm.
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or
15/32” Multi-Conductor
110 Series Split drum design 7,000 M of 7/32” (23,000 ft) 7,000 M of 5/16” (23,000 ft)
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA1-400SS series draw-works winch assembly is a stainless steel single drum hydraulic winch designed for heavy duty open hole logging service work applications. Available in single line or split drum configuration. The 2 speed electric over hydraulic shift planetary gear box with direct mount 2 speed hy-draulic motor drive system offers a wide range of line speeds and line pulling power suitable for heavy logging service work in open hole operations, winch designs for mo-bile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 2 speed planetary gear box with direct mount 2 speed hydraulic motor
• Electric shift selector • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA1-400SS SE R I E S WI NC H
Single SS Drum Logging Winch 2 Speed Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 415 mpm (1,360 fpm) Max Pull - Core 15,000 kg (33,000 lbs) Max Pull - Rim 6,100 kg (13,420 lbs) Drive specifications can be adjusted to best fit service applications Speeds as low as 1 mpm.
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or
15/32” Multi-Conductor
110 Series Split drum design 7,000 M of 7/32” (23,000 ft) 7,000 M of 5/16” (23,000 ft)
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA1-410 series drawworks winch assembly is a single split drum hydraulic winch designed for heavy duty logging service work applications. Available in single line or split drum configuration. The 2 speed electric over hydraulic shift planetary gear box with direct mount 2 speed hydraulic motor drive system offers a wide range of line speeds and line pulling power suitable for heavy logging service work in case hole and or open hole operations, winch designs for mo-bile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 2 speed planetary gear box with direct mount 2 speed hydraulic motor
• Electric shift selector • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA1-410 SE R I E S WI NC H
Single Split Drum Logging Winch 2 Speed Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 415 mpm (1,360 fpm) Max Pull - Core 15,000 kg (33,000 lbs) Max Pull - Rim 6,100 kg (13,420 lbs) Drive specifications can be adjusted to best fit service applications Speeds as low as 1 mpm.
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or 3/8” Braided Line or
15/32” Multi-Conductor
110 Series Split drum design 7,000 M of 7/32” (23,000 ft) 7,000 M of 5/16” (23,000 ft)
or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA2-300 Series drawworks winch assembly is a double drum hydraulic winch designed for perfo-rating logging applications. The dive system consist of each drum having a single speed direct mount planetary gear box with direct mount 2 speed hydraulic motor. It offers a wide range of line speeds and line pulling power suitable for logging service work in case hole operations. The double drum con-figuration allows operators the flexi-bility of having different line sizes for specialized services. Winch de-signs for mobile skid units and for land based truck mounted applica-tions. Features: • High performance with a wide
range of line pulling and line speeds
• Direct mount planetary gear box with direct mount 2 speed hy-draulic motor
• Electric motor shift • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system Options: • Spooler system • Weight indicator gauge and
load cell • Measure heads • Electronic measuring system
LA2-300 SE RI E S WI NC H
Double Drum Logging Winch Two Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 470 mpm (1,540 fpm) Max Pull - Core 3,100 kg (8,800 lbs) Max Pull - Rim 1,800 kg (4,000 lbs) Drive specifications can be adjusted to best fit service applications
Drum Line Capacity:
Each drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Model LA2-400 series drawworks winch assembly is a double drum hydraulic winch designed for heavy duty logging service work applica-tions. The drive system consist of each drum having a 2 speed electric over hydraulic shift planetary gear box with direct mount 2 speed hy-draulic motor. It offers a wide range of line speeds and line pulling power suitable for heavy logging service work in case hole and or open hole operations. The double drum configuration allows operators the flexibility of having different line sizes for specialized services, designs for mo-bile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 2 speed planetary gear box with direct mount 2 speed hydraulic motor
• Electric shift selector • Constant low speed for logging
application • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearing • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system for
line speed, depth and weight
LA2-400 SE RI E S WI NC H
Double Drum Logging Winch Two 2 Speed Direct Mount Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 415 mpm (1,360 fpm) Max Pull - Core 15,000 kg (33,000 lbs) Max Pull - Rim 6,100 kg (13,420 lbs) Drive specifications can be adjusted to best fit service applications Speeds as low as 1 mpm.
Drum Line Capacity:
Typical drum design can hold Up to 7,600 M (25,000 ft) of
7/32” Braided Line or 1/4” Braided Line or 5/16” Braided Line or
15/32” Multi-Conductor
DYNAWINCH INDUSTRIES LTD. 6771 84TH STREET SE CALGARY, AB T2C 4T6
Revised April 06
Drawworks Winch Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 4 The following series of drawworks winch equipment are base units where modifications or design changes can be made to better fit the wireline service applications.
Slickline Drawworks Winch Units • SA1 - 110 Single split drum with 4spd transmission chain drive
• SA1 - 110-D Single split drum with 4spd transmission chain drive and drop spool attachment
• SA1 - 200-D Single drum with 2spd planetary chain drive and drop spool attachment
• SA1 - 210 Single split drum with 2spd planetary chain drive
• SA1 - 300 Light Duty single drum with direct mount planetary drive
• SA1 - 320 Medium duty single drum with direct mount planetary drive
• SA1 - 500 Light duty drop spool winch system with direct drive motor
• SA1 - 520 Medium duty drop spool winch system with 2spd planetary chain drive
• SA1 - 550 Single drum re-spooler winch system with direct drive rotary motor
Logging Drawworks Winch Units • LA1 - 100 Single drum with 3spd transmission drive
• LA1 - 200 Single drum with planetary chain drive
• LA1 - 310 Single split drum with direct mount planetary drive
• LA1 - 400 Single drum with 2spd direct mount planetary drive
• LA1 - 400SS Stainless steel single drum with 2spd direct mount planetary drive
• LA1 - 410 Single split drum with 2spd direct mount planetary drive
• LA2 - 300 Double drum with two direct mount planetary drive systems
• LA2 - 400 Double drum with two 2spd direct mount planetary drive systems
Combination Drawworks Winch Units • CA2 - 615 Double drum with planetary drive on slickline drum and 3spd transmission on braided drum
• CA2 - 720 Double drum with transmission drive on slickline drum and planetary drive on braided drum
• CA2 - 840 Double drum with two direct mount planetary drive systems
Model CA2-615 series drawworks winch assembly is a double drum hydraulic winch designed for combi-nation wireline service work applica-tions. Both drums available in sin-gle line or split drum configuration. The braided drum has a 3 speed manual transmission with direct mount 2 speed hydraulic motor, the slick-line drum has a single speed plane-tary gear box with direct mount 2 speed hydraulic motor drive sys-tem . This combination drawworks offers a wide range of line speeds and line pulling power on both drums suitable for a variety of wire-line service work, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 3 speed manual transmission with direct mount 2 speed hy-draulic motor
• Planetary gear box with direct mount 2 speed hydraulic motor
• Electric over air shift selector • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearings • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system
CA2-615 SE R I E S WI NC H
Double Drum Combination Winch 3 Speed Transmission & Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Braided Drum Winch Hoist Specification:
Max Speed - Core 180 mpm (370 fpm) Max Speed - Rim 430 mpm (880 fpm) Max Pull - Core 12,000 kg (26,000 lbs) Max Pull - Rim 7,000 kg (15,400 lbs)
Typical drum design can hold Up to 6,100 M (20,000 ft) of
3/16” - 7/32” - 1/4” - 5/16” Cable or equivalent metric line sizes
Slickline Drum Winch Hoist Specification:
Max Speed - Core 420 mpm (1,400 fpm) Max Speed - Rim 600 mpm (2,000 fpm) Max Pull - Core 1,9500kg (4,300 lbs) Max Pull - Rim 1,350 kg (3,000 lbs)
Typical drum design can hold Up to 7,600 M (25,000 ft) of
.092” - .108” - .125” Line or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY , AB T2C 4T6
Revised April 06
Model CA2-720 series drawworks winch assembly is a double split drum hydraulic winch designed for a combination of wireline service work applications. Both drums available in single line or split drum configuration. The braided drum has a 2 speed electric over hydrau-lic shift planetary gear box with di-rect mount 2 speed hydraulic motor, the slickline drum has a 4 speed manual transmission hydraulic drive system . This combination draw-works offers a wide range of line speeds and line pulling power on both drums suitable for a variety of wireline service work, winch designs for mobile skid units and for land based truck mounted applications.
Features: • High performance with a wide
range of line pulling and line speeds
• 4 speed manual transmission with direct mount hydraulic mo-tor
• 2 speed planetary gear box with direct mount 2 speed hydraulic motor
• Electric over air shift selector • Close-loop hydraulic system • Machined balanced steel drum • Dual band brakes with air oper-
ated controls • HD drum shaft bearings • Split or non split drum configu-
rations • Prepped, primed and painted • Minimum maintenance system
Options: • Spooling system • Measure heads • Electronic measuring system
CA2-720 SE R I E S WI NC H
Double Split Drum Combination Winch 4 Speed Transmission & Planetary Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Braided Drum Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 415 mpm (1,360 fpm) Max Pull - Core 15,000 kg (33,000 lbs) Max Pull - Rim 6,100 kg (13,420 lbs)
Typical drum design can hold Up to 6,100 M (20,000 ft) of
3/16” - 7/32” - 1/4” - 5/16” Cable or equivalent metric line sizes
Slickline Drum Winch Hoist Specification:
Max Speed - Core 518 mpm (1,700 fpm) Max Speed - Rim 750 mpm (2,450 fpm) Max Pull - Core 4,300 kg (9,500 lbs) Max Pull - Rim 3,100 kg ( 7,000 lbs)
Typical drum design can hold Up to 7,600 M (25,000 ft) of
.092” - .108” - .125” - .140” Line or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 8t4h STREET SE CALGARY , AB T2C 4T6
Revised April 06
Model CA2-840 series drawworks winch assembly is a double drum hydraulic winch designed for a com-bination of wireline service work applications. The braided drum has a 2 speed electric over hydraulic shift planetary gear box with direct mount 2 speed hydraulic motor and the slickline drum has a single speed planetary gear box with 2 speed direct mount hydraulic motor drive system . The slickline drum raises for operator to have clear line of sight when in operation. This combination drawworks offers a wide range of line speeds and line pulling power on both drums suit-able for a variety of wireline service work, winch designs for mobile skid units and for land based truck mounted applications. Features: • High performance with a wide
range of line pulling and line speeds
• Braided drum drive - 2 speed planetary gear box
• Slickline drum drive - single speed planetary gear box
• Direct mount 2 speed hydraulic motors
• Electric shift on 2 speed motors • Electronic shift selector for 2
speed planetary • Close-loop hydraulic system • Machined balanced steel drum • Band brakes with air operated
controls • HD drum shaft bearings • Split or non split drum configu-
rations • Prepped, primed and painted Options: • Spooling system
CA2-840 SE R I E S WI NC H
Double Drum Combination Winch with two (2) Direct Mount Planetary Drives
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Braided Drum Winch Hoist Specification:
Max Speed - Core 150 mpm (492 fpm) Max Speed - Rim 405 mpm (1,330 fpm) Max Pull - Core 15,000 kg (33,000 lbs) Max Pull - Rim 6,900 kg (15,200 lbs)
Typical split drum design can hold Up to 7,100 M (23,000 ft) of
3/16” - 7/32” - 1/4” - 5/16” Cable or equivalent metric line sizes
Slickline Drum Winch Hoist Specification:
Max Speed - Core 330 mpm (1,080 fpm) Max Speed - Rim 490 mpm (1,600 fpm) Max Pull - Core 2,800 kg (6,100 lbs) Max Pull - Rim 1,800 kg ( 3,900 lbs)
Typical drum design can hold Up to 7,600 M (25,000 ft) of
.092” - .108” - .125” Line or equivalent metric line sizes
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
DYNAWINCH INDUSTRIES LTD. 6771—84TH STREET SE, CALGARY, AB T2C 4T6
Section 5
Wireline Accessory Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 5 The following series of wireline accessory equipment are base units where modifications or design changes can be made to better fit the wireline service applications. Generators • GEN - 100 10kw hydraulic drive generator package
Spooler Skid Units • PS1 - 100 Wireline spooler skid with diesel engine
Grease Pump Control Units • GS1 - 100 5K Grease pump skid with diesel engine
Data Van Units • DV/UV Custom design aluminum data/utility vans
Operator Control Cabs • Control Cab Custom design operator control cabs
Model GEN-100 series hydraulic driven AC generators offer low noise level operating while providing smooth trouble free AC power un-der most demanding conditions. This compact and lightweight gen-erator package design make this it a primary choice for AC power in many oilfield equipment applica-tions.
Generator Features:
• Brushless AC generator • Advanced automatic voltage
regulator (AVR) control • Easy paralleling with mains or
other generators • Standard 2/3 pitch windings
avoid excessive neutral cur-rents
• Dynamically balanced rotor • Sealed-for-life ball bearings • Standard features in 50 Hz or
60 Hz frequencies • Standard features available in
120V or 240V power output • Models range from 6 KW to 32 KW • CE compliance • Minimum maintenance system • Five (5) rubber shock mounts
Accessories:
• Shore power cord • Grounding rod and cable • LED frequency and volt meters
GEN-100 SE RI E S
AC Generator System Hydraulic Drive
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Hydraulic System:
• Engineered hydraulic open loop circuit design
• Custom design hydraulic motor mount plate
• Direct mount hydraulic motor to generator rotor
• Variable displacement axial pis-ton hydraulic motor
• Variable displacement axial pis-ton pump with load sensing valve
• Oil cooler with automatic tem-perature sensing cooling fan
Dimensions:
Dimensions for a 10kw generator system with hydraulic motor and cooler
78 cm L x 50 cm W x 50 cm H (31 in L x 20 in W x 20 in H)
Weight (Dry) 120 kg
(265 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Wireline Accessory Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 5 The following series of wireline accessory equipment are base units where modifications or design changes can be made to better fit the wireline service applications. Generators • GEN - 100 10kw hydraulic drive generator package
Spooler Skid Units • PS1 - 100 Wireline spooler skid with diesel engine
Grease Pump Control Units • GS1 - 100 5K Grease pump skid with diesel engine
Data Van Units • DV/UV Custom design aluminum data/utility vans
Operator Control Cabs • Control Cab Custom design operator control cabs
Model PS1-100 series self-contained wireline spooler and re-spooler skid is designed to work with various spool diameter sizes. This spooler skid can facilitate spooling line off spool or re-spooling line onto spool. The spooler hy-draulic system is powered by a 27 HP diesel engine providing a wide range of spooling speeds and pull-ing power for spooling line.
Features:
• All steel skid structure with fork-lift pockets and lifting tubes for four point lifting
• 27 HP diesel engine • Variable displacement pump
with electronic joystick pump controller
• Operator’s control panel • Frame assembly to handle
large diameter spools • Heavy duty hydraulic motor
spool drive • Shaft and drive adapter for steel
spools • Shaft and drive adapter for
wood spools • Mechanical disc brake with
brake handle on control panel
Accessories:
• Operator's seat • Remote auxiliary equipment
hydraulic power supply • Work lights
PS1-100 SE R I E S
Wireline Spooler Skid with Diesel Power Pack
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Winch Hoist Specification: Max Speed - Core 205 mpm (670 fpm) Max Speed - Rim 340 mpm (1,100 fpm) Max Pull - Core 640 kg (1,400 lbs) Max Pull - Rim 400 kg (850 lbs) Drive specifications can be adjusted to best fit service applications
Spool Sizes: Spool frame assembly can handle spools of up to 36” diameter, wood or steel spools for line sizes
0.092” - 0.108” - 0.125” 0.140” - 0.150” - 0.160”
Skid Dimensions:
1.9m L x 1.35m W (75 in L x 52 in W)
DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
Wireline Accessory Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 5 The following series of wireline accessory equipment are base units where modifications or design changes can be made to better fit the wireline service applications. Generators • GEN - 100 10kw hydraulic drive generator package
Spooler Skid Units • PS1 - 100 Wireline spooler skid with diesel engine
Grease Pump Control Units • GS1 - 100 5K Grease pump skid with diesel engine
Data Van Units • DV/UV Custom design aluminum data/utility vans
Operator Control Cabs • Control Cab Custom design operator control cabs
Model GS1-100 series self con-tained 5,000 PSI rated grease pump skid unit designed to work in mar-kets requiring portable, compact, lightweight equipment for land based applications. The hydraulic grease pump system is powered by a 14 HP diesel engine, suitable to provide grease pressure to pressure control equipment.
Generator Features:
• Steel skid frame with crash cage
• Two sets of forklift pockets, ac-cess from sides and ends
• Four point lifting lugs • 14 HP diesel engine power
pack • 5,000 PSI rated hydraulic recip-
rocating grease pump • Two grease tanks • Operator’s stainless steel con-
trol panel • 5,000 PSI manual hose reel
with 125 ft x 1/2” HP hose • 5,000 PSI manual hose reel
with 125 ft x 1/2” return hose • Tool storage compartment • Minimum maintenance system • Prepped, primed and painted
GS1-100 SE R I E S
5K Grease Pump Skid Unit with Diesel Power Pack
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected]
Hydraulic System:
• Engineered hydraulic closed loop circuit design
• Variable displacement pump • Pressure regulating valve • Needle valves • Pressure gauges
Dimensions:
1.4 m L x 1.0 m W x 1.0 m H (55 in L x 40 in W x 40 in H)
Weight (Dry) 300 kg
(650 lbs)
DYNAWINCH INDUSTRIES LTD. 6771 - 84TH STREET SE, CALGARY ALBERTA T2C 4T6
Revised April 06
Wireline Accessory Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 5 The following series of wireline accessory equipment are base units where modifications or design changes can be made to better fit the wireline service applications. Generators • GEN - 100 10kw hydraulic drive generator package
Spooler Skid Units • PS1 - 100 Wireline spooler skid with diesel engine
Grease Pump Control Units • GS1 - 100 5K Grease pump skid with diesel engine
Data Van Units • DV/UV Custom design aluminum data/utility vans
Operator Control Cabs • Control Cab Custom design operator control cabs
Custom Design Aluminum Data Vans
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
12’ Utility Data or Service Van UV1 - 900
DynaWinch manufactures a variety of aluminum Data and Service vans for various applications, which are custom designed to clients requirements. Van configurations available include, but are not limited to:
14’ Mini Data Van DV1 - 910
10’ Mini Data Van DV1 - 900
26’ HD Data Van DV2 - 920
Wireline Accessory Equipment Product Line Model Series Numbers
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Section 5 The following series of wireline accessory equipment are base units where modifications or design changes can be made to better fit the wireline service applications. Generators • GEN - 100 10kw hydraulic drive generator package
Spooler Skid Units • PS1 - 100 Wireline spooler skid with diesel engine
Grease Pump Control Units • GS1 - 100 5K Grease pump skid with diesel engine
Data Van Units • DV/UV Custom design aluminum data/utility vans
Operator Control Cabs • Control Cab Custom design operator control cabs
Custom Design Operator Control Cabs
WEB PAGE: TEL: FAX: E-MAIL:
www.dynawinch.com 403-319-2333 403-319-2337 [email protected] DYNAWINCH INDUSTRIES LTD. 6771 - 84th STREET SE CALGARY, AB T2C 4T6
Revised April 06
DynaWinch manufactures a variety of aluminum Operator Control Cabs, which are custom designed for a variety of different applications and industries. Cab configurations include, but are not limited to: