DYWIDAG Geotechnical Product Range
2
Contents
About us ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 4
DYNA Force® Sensors for Load Monitoring ������������������������������������������������������������������������������������������������������������������������������������������ 5
DYWIDAG Micropiles – GEWI® Pile ������������������������������������������������������������������������������������������������������������������������������������������������������ 8
DYWIDAG Micropiles with DYWI® Drill Hollow Bar ����������������������������������������������������������������������������������������������������������������������������� 10
DYWIDAG Tie Rods ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 12
DYWIDAG Soil Nails ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 16
DYWIDAG Rock Bolts ������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 20
DYWIDAG THREADBAR® Anchors ����������������������������������������������������������������������������������������������������������������������������������������������������� 22
DYWIDAG THREADBAR® Anchors – Removable ������������������������������������������������������������������������������������������������������������������������������� 23
Bar Properties ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 26
Hardware Properties ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 27
DYWIDAG Strand Anchors ����������������������������������������������������������������������������������������������������������������������������������������������������������������� 28
DYWIDAG Strand Anchors Properties ������������������������������������������������������������������������������������������������������������������������������������������������ 29
Geotechnical Equipment �������������������������������������������������������������������������������������������������������������������������������������������������������������������� 34
3
Provo Canyon, UtahDCP DYWIDAG Strand Anchors – page 28
Dallas Cowboys Stadium, TexasDYWIDAG Soil Nails – page 16
About us
DSI’s anchor and piling systems and related products are used for a wide variety of geotechnical applications such as the stabilization of slopes and excavations, substructure foundation needs as well as the counteraction of uplift forces for both new structures and for the rehabilitation of existing structures�
As a leading supplier of geotechnical products and systems, DSI provides complete services� Backed by many years of experience in all types and scopes of construction projects, DSI specialists support their clients in every project phase from planning to the supply of high quality DSI systems and the execution of work on the construction site, including quality management and monitoring services�
Systematic research in the fields of materials, structural engineering and construction methods has provided DSI with a constant flow of innovative ideas� Progressive development, combined with a commitment to the highest quality standards, is DSI’s response to the changing needs of current and future construction markets�
The DSI business philosophy is based on the establishment and cultivation of a trustworthy business relationship with its clients� Irrespective of circumstances, DSI is committed to fulfilling the tasks entrusted by its clients - always in accordance with its slogan:
“Local Presence – Global Competence”.
4
DYNA Force® Sensors for Load Monitoring
Introduction
On many occasions during the construction and service life of a structure, it is beneficial to know the force in the tension element of the post-tensioning system� Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy differs
depending on the method used� DYWIDAG has been involved in the development, testing and execution of DYNA Force® to measure the force in the tendon� DYNA Force® is utilized for ground anchors, soil nails, in cable stay bridges and structures to measure the forces during construction and to
monitor forces during the service life of the structure� Valuable information about load distribution can be obtained if sensors are placed along the bond length of ground anchors or soil nails� DYNA Force® can be used for bare, epoxy-coated and greased-sheathed steel�
Advantages and Characteristics
DYNA Force® is manufactured based on the theory that the permeability of steel to a magnetic field changes with the stress level in the steel� By measuring the change in a magnetic field, the magnitude of the stress in the steel element can be obtained� The DYNA Force® system does not alter the characteristics of the tendon other than its magnetization� The permeability is a function of temperature and magnetization� A calibration process eliminates the impact of these variables� The system considers the effect of the temperature change automatically�
A portable Power Stress unit is attached to wire leads from the DYNA Force® sensor� This unit will create the magnetic field, measure the residual value and then convert it to a direct force reading�
The DYNA Force® system is robust, requires no maintenance and has no moving parts� It is composed of cylindrical, non-contact sensors and a Power Stress unit (read-out box)� DYNA Force® sensors are installed over the strand or bar during construction and a zero reading is taken before applying any post-tensioning force�
It is expected to have a similar service life as structure� This will allow the owner to regularly monitor the forces in the post-tensioning system in minutes as a part of their inspection procedures without the need for lift-off equipment or other special expensive techniques� Monitoring with DYNA Force® also avoids the inaccuracies and risks often associated with lift-off readings� Performing the monitoring requires only one person�
5
DYNA Force® Sensors for Load Monitoring
DYNA Force® Dimensions
Strand Size Strand Grade Sensor Inside Diameter Sensor Outside Diameter Sensor Length
[in] [mm] [ksi] [MPa] [in] [mm] [in] [mm] [in] [mm]
0�5" - 0�62" 12�7 - 15�7 270 1,860 0�79 20 1�42 36 5�20 132
DYWIDAG THREADBAR® Size
DYWIDAG THREADBAR® Grade Sensor Inside Diameter Sensor Outside
Diameter Sensor Length
[in] [mm] [ksi] [MPa] [in] [mm] [in] [mm] [in] [mm]
#7 - #11 16 - 35 75 - 100 517 - 690 1�69 43 3�15 80 7�09 180
#14 43 80 - 100 552 - 690 2�09 53 3�90 99 7�87 200
#18 - #20 57 - 63 80 - 100 552 - 690 2�87 73 5�71 145 12�20 310
#24 75 75 - 100 517 - 690 3�35 85 6�10 155 12�99 330
1" - 1 ⅜" 23 - 36 150 1,034 1�69 43 3�15 80 7�09 180
1 ¾" 46 150 1,034 2�09 53 3�90 99 7�87 200
2 ½" 66 150 1,034 2�87 73 5�71 145 12�20 310
3" 75 150 1,034 3�35 85 6�10 155 12�99 330
6
DYNA Force® Sensors for Load Monitoring
Remote Load Monitoring of Ground Anchors at Willow Island Hydroelectric Project, West Virginia, USA
DSI supplied twenty-eight 59-0�6" strand anchors for the stability and safety of the dam at the Willow Island Hydroelectric project in West Virginia, USA� Rock mass was excavated to allow for the installation of a power generator�
In order to monitor the forces in the anchors during rock excavation, three sensors were installed in each anchor� A total of 84 DYNA Force® Sensors were installed in these permanent rock anchors� All sensors were connected to a multiplexer using extension cables, and all multiplexers were connected to the readout unit via main cable� Modem, controller and Cell SIM card were installed so the data could be accessed from a remote location� Battery and solar panels were used to power the readout unit� The data from all of the sensors are being taken remotely every three hours, analyzed and reported to the owner�
Continuous Monitoring of Ground Anchors at Sellwood Bridge, Oregon, USA
DSI supplied 56 DYNA Force® Sensors for both permanent and test ground anchors for Sellwood Bridge in Oregon, USA� The main purpose was to monitor the slope stability in front of the bridge abutment� Six sensors were installed in the bond length and one in the free length of each of the test anchors� Two sensors were installed in each of the permanent anchors, with the number of strands varying from 8 to 24� Fifteen automated readout units were installed to record the force readings of the sensors every four hours� Software was provided so that the engineer could transfer the recorded data to a laptop� DYNA Force® Sensors provided valuable information for both test and permanent anchors�
DYNA Force® for rock anchor at Willow Island Hydroelectric Project, West Virginia, USA
DYNA Force® for ground anchors at Sellwood Bridge, Oregon, USA
7
Bearing Plate
Hex Nut
Plastic Centralizer
Coupler
DYWIDAG THREADBAR®
Shop grouted Corrugated
Plastic Sheathing
Coupler with Corrosion Protection
Low headroom installation Multiple bar GEWI® Pile for windmill retrofit
Hex Nut
Concrete Structure
DYWIDAG THREADBAR®
Bearing Plate
Hex Nut
Hex Nut
Concrete Structure
Plastic Centralizer
Drilled Hole Cement Grout (field installed)
Drilled Hole Cement Grout (field installed)
End Cap
DYWIDAG Micropiles – GEWI® Pile
A GEWI® Pile is a drilled and grouted micropile, with a diameter of less than 12 inches� It is centrally reinforced with either one or a group of DYWIDAG THREADBARS� The deformations on the bar transfer the load into the surrounding grout body and friction transfers the load from the grout into the ground�
Drilling: ■ Compact lightweight drilling equipment allows for pile installation even in areas with low headroom
■ Small economic drill hole diameters ■ Drill holes can be placed closely to existing walls or structures
■ Vibration free drilling prevents damage to adjacent structures
Continuous coarse thread on bars: ■ Provides excellent load transfer into grout
■ Remains threadable even when dirty or damaged
■ Allows for splicing and extending the bar at any point
Double Corrosion Protected (DCP) bars may be utilized for piles in aggressive ground�
Multiple bars can be installed into a single borehole�
Short bar sections with couplers can be utilized in low headroom locations�
GEWI® Pile with Single Corrosion Protection (SCP)
GEWI® Pile with Double Corrosion Protection (DCP)
8
Project References DYWIDAG Micropiles
The Newport Bay Marina: Stable underwater Foundations with DYWIDAG Micropiles, CA, USA
Client ETCO Homes Inc�, USA +++ General Contractor Wieland-Davco Corporation, USA +++ Subcontractor DVertical Earthworks, Inc�, USA +++ Consulting Engineers Earth Support Systems Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supplyDYWIDAG Products 624 12�2m long, 57mm Ø DCP GEWI® Micropiles
GEWI® Micropiles stabilize Important Motorway Connection in the Netherlands
Owner Ministry of Transport, major projects department, Netherlands +++ General Contractor JV A4 Burgerveen – Leiden, consisting of BAM Civiel, BAM Wegen, VTN Verkeers- & Besturingstechniek bv and Van Oord, all of them Netherlands +++ Subcontractor BAM Speciale Technieken, Netherlands +++ Engineering BAM Infraconsult bv, Netherlands
DSI Unit DYWIDAG-Systems International B�V�, NetherlandsDSI Scope Production, supplyDYWIDAG Products 10,000 GEWI® Micropiles with 20,000 Anchorages
9
Drill Bit
Simultaneous Drilling and Grouting
Drilled Hole Cement Grout
(injected during drilling process)
DYWI® Drill Hollow Bar
Bearing Plate
Hex Nut
Hex Nut
Concrete Structure
Coupler
Various Style Drill Bits
DYWIDAG Micropiles with DYWI® Drill Hollow Bar
Micropile with DYWI® Drill Hollow Bar
Advantages and Characteristics
The DYWI® Drill Hollow Bar System consists of fully threaded steel bar sections, couplers, nuts and drill bits� It can be drilled and grouted into loose or collapsible soil without a casing� The bar sections feature a hollow center that allows for a simultaneous drilling and grouting operation�
■ System can be installed in confined spaces utilizing simple and compact drilling equipment�
■ Drilling and grouting in a single simultaneous operation
■ Bars and hardware can be epoxy coated or galvanized
■ Optional sacrificial steel corrosion allowance method is applicable to micropile applications using oversized hollow bars to allow for loss of cross sectional area due to corrosion�
■ Drill bits are available for various ground conditions
■ Irregular grout body enhances pile capacity
DYWI® Drill Hollow Bar Properties
Bar Designation
Nominal Outer Diameter
Average Yield Strength
(fy)
Average Ultimate Tensile
Strength (fu)
Average Cross Section Area
(As)
Yield Load
(fy x As)
Ultimate Load
(fu x As)Nominal Weight
[in] [mm] [ksi] [MPa] [ksi] [MPa] [in²] [mm²] [kips] [kN] [kips] [kN] [lbs/ft] [kg/m]R25N 1.00 25 87 600 116 800 0.39 250 34 150 45 200 1.34 2.00R32N 1.26 32 95 657 116 800 0.54 350 52 230 63 280 1.81 2.70R32S 1.26 32 94 651 121 837 0.67 430 63 280 81 360 2.28 3.40R38N 1.50 38 98 677 123 847 0.91 590 90 400 112 500 3.16 4.70R51L 2.00 51 88 608 108 743 1.15 740 101 450 124 550 3.97 5.90T40N 1.57 40 99 681 124 857 1.19 770 118 525 148 660 4.03 6.00R51N 2.00 51 97 670 123 851 1.46 940 142 630 180 800 4.97 7.40T76N 3.00 76 84 576 112 769 3.22 2,080 270 1,200 360 1,600 10.95 16.30T76S 3.00 76 88 609 112 772 3.81 2,460 337 1,500 427 1,900 12.97 19.30
Note: Maximum allowable, temporary test tension is 100% of the yield load� Average cross section area is based on average internal diameter of the bar� The ultimate and yield load capacity are measured values� The ultimate tensile and yield strength are calculated average values� Mill length is 9'-10" (3m)� Longer lengths can be special order�
10
DYWI® Drill Hollow Bar Hardware Properties
BarDesignation
Hex Nut Length
H
Coupler Length
B
Coupler Outer Diameter
Ø C
Maximum Angle Compensation *
Bevel Washer Diameter
Ø V
[in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]R25N 2.44 62 5.91 150 1.46 37 19 2.26 57R32N 2.56 65 6.30 160 1.65 42 18 2.88 73R32S 2.56 65 6.30 160 1.65 42 18 2.88 73R38N 3.15 80 7.09 180 2.01 51 19 3.20 81R51L 3.54 90 7.87 200 2.48 63T40N 2.68 68 6.30 160 2.24 57 18 3.27 83R51N 3.54 90 7.87 200 2.48 63T76N 3.15 80 8.66 220 3.82 97T76S 3.15 80 8.66 220 3.82 97
* using two washers in a set� Solutions for large bars and larger angles are available – please consult your local DSI Sales Engineer Couplers and hex nuts develop the bar ultimate load�
Project References DYWIDAG Micropiles with DYWI® Drill Hollow Bar
DYWIDAG Micropiles with DYWI® Drill Hollow Bar
DYWIDAG Micropiles with DYWI® Drill Hollow Bars secure “Electra” Building in San Diego, CA, USA
Owner Bosa Development California II, Inc, British Columbia, Canada +++ Main Contractor Bosa Development California II, Inc, British Columbia, Canada +++ Execution Condon-Johnson & Assoc� Inc�, San Diego, CA, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supplyDYWIDAG Products 10,000 ft DYWIDAG Micropiles with DYWI® Drill Hollow Bars type T76S including hardware accessories such as drill bits and couplers
11
Double C-Channels (Waler)
Bearing Plate
Hex Nut
Spacer Plate (optional)
Beam Support (optional)
Sheet Pile
Alpha-Bravo Wharf, Guam
DYWIDAG Tie Rods
Advantages and Characteristics
Tie Rods produced from DYWIDAG THREADBAR® are used for a variety of applications� Constructions of marine bulkheads for various docking facilities have, for many years, benefited from the use of DYWIDAG Tie Rods� Facilities such as barge and ship docks as well as offshore platforms have found the system to be a cost effective alternative to large diameter A36 Tie Rods with upset threads�
Additional applications for DYWIDAG Tie Rods are: ■ Stabilization of slopes ■ Horizontal load resistance for foundations and roof structures
■ Bracing for grade separations
Tie Rods produced from DYWIDAG THREADBAR® offer various economical and technical advantages: ■ Coarse thread allows for rough site handling as dirty or damaged threads will remain threadable
■ Continuous thread allows for easy on-site length adjustments since cutting or coupling of the rod is possible along its entire length
■ Stock length up to 60ft ■ Bars conform to ASTM A615 or ASTM A722
■ ASTM A615 bars are about 50% less weight than A36 bars
■ ASTM A722 bars are about 70% less weight than A36 bars
■ Available with many options for corrosion protection
■ DYWIDAG Tie Rods can be tensioned for sheet pile alignment
■ The DYWIDAG Tie Rod system is approved by many construction authorities worldwide
Waler Connection
Short bolts are needed to connect a standard sheet pile wall or a modular sheet pile wall to a load distributing double channel beam� This can be done with Grade 75 or Grade 80 DYWIDAG THREADBAR®�
The required length of the bar depends on the depth of the sheet pile profile, the width of the beam, the plate thickness and the nut length�
12
Concrete DeadmanDouble C-Channels
Steel Pipe Welded to Bearing Plate
Protective Cap
Bearing Plate
Grease or Cement Grout
Sheet Pile
Seal
Factory Injected Cement Grout
Corrugated Plastic Sheathing
DYWIDAG THREADBAR®
Spiral Wrap Spacer
Port of Everett, Washington
Hex Nut
DYWIDAG Tie Rods
DYWIDAG Tie Rod with Double Corrosion Protection (DCP)
Recommended for Permanent Applications in Agressive Enviroments
Corrosion Protection
Corrosion Protection plays an important role in the longevity of the Tie Rod system� DSI offers various options for corrosion protection in order to meet specific project requirements�
■ Fusion Bonded Epoxy Coating per ASTM A775 or ASTM A934
■ Petroleum Wax Tape Wrapping ■ Coal Tar Epoxy Coating
■ Hot Dip Galvanizing* per ASTM A123 / ASTM A153
■ Polyken 980/955 tape coating system
■ Double Corrosion Protection (DCP)
Bars are pre-grouted into a plastic corrugated sheathing to protect the steel in most aggressive environments�
* Not recommended for 150ksi steels�
13
Project References DYWIDAG Tie Rods
DYWIDAG Tie Rods create better Access: New Pier on Akutan, AK, USA
Owner Trident Seafoods Inc�, USA +++ General Contractor Western Marine Construction, Inc�, USA +++ Consulting Engineers Northern Geotechnical Engineering, Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supplyDYWIDAG Products 170 Ø 57mm DYWIDAG Tie Rods, 11 Ø 43mm DYWIDAG Tie Rods
Modernization of Newport International Terminal using DYWIDAG Tie Rods, Newport, OR, USA
Client Port of Newport, USA +++ General Contractor NATT McDougall Company, USA +++ Contractor DBM Contractors, Inc�, USA +++ Architect KPFF Consulting Engineers, Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope SupplyDYWIDAG Products 24 6-0�6" DCP DYWIDAG Strand Anchors, 19 2�5" Grade 150 and 3�0" Grade 150 DCP DYWIDAG Tie Rods, 21 57mm Grade 75 DYWIDAG Micropiles
14
Project References DYWIDAG Tie Rods
Comfort and Design: The Marina d’Arechi, Italy
Owner Gallozzi Group, Italy +++ General Contractor Impresa Pietro Cidonio S�p�A�, Italy +++ Architect (Marina Buildings) Santiago Calatrava, Spain
DSI Unit DYWIT S�P�A�, ItalyDYWIT Scope SupplyDYWIDAG Products 7,600m of double corrosion protected Ø 50mm DYWIDAG Tie Rods made of GEWI® steel
DYWIDAG Tie Rods for US-American Base in Guam, Micronesia, USA
Owner US Navy, Naval Base Guam, USA +++ General Contractor Black Construction Corporation, Guam, USA +++Architect-Engineers Wilson Okamoto Corporation, Honolulu, Hawaii, USA
DSI Unit DYWIDAG-Systems International USA Inc�, USADSI Scope Supply DYWIDAG Products approx� 8,000m (26,000ft�), of DYWIDAG Tie Rods with Polyken tape wrap
15
Bearing Plate
DYWIDAG THREADBAR®
(grouted at DSI prior to shipment to site)
Nut
Bevel Washers Shotcrete
CentralizerCement Grout
Bearing Plate
DYWI® DrillHollow Bar
Nut
Bevel Washers Shotcrete
CouplerCement Grout
Drill Bit
Bearing Plate
Cement Grout
Bevel Washers Shotcrete
DYWIDAG THREADBAR®Centralizer End Cap
Nut
Studs
Corrugated Plastic Sheathing
DYWIDAG Soil Nails
Advantages and Characteristics
of Soil Nail Walls ■ Top-down construction ■ Light construction equipment ■ Lower construction costs versus tieback walls with soldier beams and lagging
of DYWIDAG Soil Nails ■ Can be used for temporary and permanent applications
■ Simple components and assembly ■ Easy to install and test ■ Durable threads� Allow splicing at any point along the bar
Introduction
DSI has been a pioneer in the use of soil nails to reinforce existing ground� Today DSI is widely recognized as the principal worldwide source for soil nails meeting the most demanding performance requirements�
DYWI® Drill Soil Nail bare, epoxy coated or galvanized
DYWIDAG DCP Soil Nail for the most aggressive Soil Conditions
THREADBAR® Soil Nail bare or epoxy coated
SEE PAGE 10 FOR ADVANTAGES AND CHARACTERISTICS OF DYWI®
DRILL HOLLOW BAR SYSTEM
16
THREADBAR® Anchorage with Studs DYWI® Drill Hollow Bar Anchorage without Studs
Children’s Hospital San Diego, California
THREADBAR® with Centralizer Various Style Drill Bits for DYWI® Drill Soil Nails
Epoxy coated DYWI® Drill Soil Nails
DYWIDAG Soil Nails
Bearing Plate Assembly
Bearing plates are available in any size with or without welded concrete anchors (studs)�
ASTM A36 and ASTM A572 grade 50 steel material are used for the bearing plates, stud materials conform generally to ASTM A108�
One or two beveled washers are typically used to adjust to the soil nail angle�
Centralizers
Centralizers made from PVC are available for all hole diameters and nail configurations� They are typically used with THREADBAR® and DCP Soil Nails�
Drill Bits
Drill bits for DYWI® Drill Hollow Bars are available for varying ground conditions�
SEE PAGES 26 & 27FOR BAR AND HARDWARE
PROPERTIES
17
Project References DYWIDAG Soil Nails
Bluff Park: DYWIDAG Soil Nails secure the nicest View of the Pacific Ocean in Long Beach, CA, USA
Owner Long Beach City Council, USA +++ General Contractor Drill Tech Drilling and Shoring Inc�, USA +++ Engineering Kleinfelder, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supplyDYWIDAG Products 1,695 double corrosion protected Ø 25mm DYWIDAG Soil Nail
DYWIDAG Strand Anchors with DYNA Force® Sensors for Retaining Walls of the Sepulveda Pass, I-405 Project, Los Angeles, CA, USA
Owner California Department of Transportation (CALTRANS) Los Angeles Metropolitan Transportation Authority (Metro) +++ General Contractor Kiewit Pacific Company, USA +++ Retaining Walls Subcontractor Drill Tech Drilling and Shoring, Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production and SupplyDYWIDAG Products Double Corrosion Protected (DCP) DYWIDAG Soil Nails, 500 Permanent 5-0�6" and 7-0�6" DCP DYWIDAG Strand Tieback Anchors and of 48 DYNA Force® Strand Sensors; technical equipment
18
Project References DYWIDAG Soil Nails
DYWIDAG Soil Nails stabilize excavation of the Dallas Cowboy Stadium, TX, USA
General Contractor Consortium: Manhatten Construction Company, Rayco Construction and 3i Construction, all Dallas, Texas, USA +++ Contractor Craig Olden Co�, Little Elm, Texas, USA +++ Architect HKS Sports & Entertainment Group, Inc�, Dallas, Texas, USA +++ Engineer Graham & Associates, Inc�, Illinois, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supplyDYWIDAG Products 18,200 double corrosion protected, Grade 150 epoxy coated DYWIDAG Soil Nails (670 t)
DSI Supports Washington State Department of Transportation during the Construction of its Tallest Soil Nail Wall, WA, USA
Owner Washington State Department of Transportation (WDOT), Olympia, USA +++ General Contractor Mowat Construction Company, Woodinville, WA, USA +++ Contractor Drilling Work Northwest Cascade, Inc�, Puyallup, WA, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supply DYWIDAG Products 387 Epoxy Coated DYWIDAG Soil Nails and of approximately 1,470 Double Corrosion Protected DYWIDAG Soil Nails in lengths of 26m
19
Bearing Plate
Hex Nut
Bevel WashersDYWIDAG
THREADBAR® Cement Grout Expansion Shell
DYWIDAG Rock Bolts
Advantages and Characteristics
■ High loads with small drill hole diameters
■ Continuous bar thread allows cutting at any point and length adjustment on site
■ Coarse thread is insensitive to rough handling
■ High bond along the bar length for anchoring into resin or cement grout
■ Good mixing of resin cartridges with the thread deformations of the bar
■ Resin or expansion shells allow for quick loading of the bolt
SEE PAGES 26 & 27FOR BAR AND HARDWARE
PROPERTIES
Bearing Plate
Hex Nut
Bevel WashersDYWIDAG
THREADBAR® Cement Grout
DYWIDAG Grouted Bolt
Bearing Plate
Hex Nut
Bevel WashersDYWIDAG
THREADBAR®Slow Setting Resin
or Cement Grout Fast Setting Resin
DYWIDAG Resin Bolt
DYWIDAG Expansion Shell Bolt
20
Project ReferencesProject References DYWIDAG Rock Bolts
Stairway Rehabilitation at 183rd St & Tiebout Ave., Bronx, NY, USA
Owner City of New York, Department of Design and Construction, NY, USA +++ General Contractor LAWS Construction,Pleasantville, NY, USA +++ Contractor JANOD Construction Inc�, USA +++ Engineers Langan Engineering & Environmental Services,New York, NY, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, Toughkenamon, PA, USADSI Scope Production, supply DYWIDAG Products #8 grade 75: S 520/690 N/mm² epoxy-coated DYWIDAG Rock Bolts incl� accessories: hex nuts, eyebolts and anchor plates
Spectacular Use of DYWIDAG Systems: The Glacier Skywalk in Jasper National Park, AB, Canada
Owner Brewster Travel Canada, Canada +++ General Contractor PCL Constructors Inc�, Canada +++ Subcontractor Josef Gartner GmbH, USA, BOVA Steel Inc� and BAT Construction Ltd�, both Canada +++ Consulting Engineers Read Jones Christoffersen Consulting Engineers (RJC), Canada +++ Architect Sturgess Architecture, Canada +++ Engineering (Geotechnics) Thurber Engineering Ltd�, Canada
DSI Unit DYWIDAG-Systems International Canada Ltd�, Western Division, CanadaDSI Scope Production, supply, installation, technical support, supervisionDYWIDAG Products 48 Ø 63mm DYWIDAG Rock Anchors; 64 Ø 46mm GEWI® Micropiles; Ø 46mm DCP DYWIDAG Rock Anchors; 77 Ø 46mm THREADBAR® Post-Tensioning Tendons; 80 Ø 36mm DYWIDAG Anchors; 2 Type 9-0�6" DYWIDAG Strand Tendons
21
Wedge Washer
Anchor Nut Anchor Plate
Bearing Washer
Smooth Sheathing (bond breaker)
Tape Seal
Anchor Nut Anchor Plate
Cover Cap
Corrosion Inhibiting Grease or Cement Grout
Corrosion Inhibiting Grease or Cement Grout
Smooth Sheathing (bond breaker)
Cement Grout(shop injected) Tape Seal
Corrugated Plastic Sheating
Steel Pipe DYWIDAG THREADBAR®
Centralizer End Cap
DYWIDAG THREADBAR® Anchors with DCP Santa Monica Blvd�, Santa Monica, California
CentralizerDYWIDAG
THREADBAR®
Cement Grout
DYWIDAG THREADBAR® Anchors
DYWIDAG Temporary Anchor
DYWIDAG Permanent (DCP) Anchor
SEE PAGES 26 & 27FOR BAR AND HARDWARE
PROPERTIES
Advantages and Characteristics
■ Easy to handle, install and stress ■ Simple restressing or detensioning ■ Easy removal of temporary anchors if required
■ Coupler systems allow for supply of anchor in multiple sections
■ High load transfer between THREADBAR® and cement grout
■ Anchor length can be increased on site if required
■ Simple hardware for angle compensation
■ Double Corrosion Protection (DCP) available for permanent anchors
■ Specialized stressing equipment is available from DSI
22
DYWIDAG THREADBAR® Anchors (partially removable) Park Terrace, San Diego, California
Anchor Nut Bearing Plate
Angle Pipe
Bearing Plate
Smooth Sheathing
DYWIDAG THREADBAR® Coupler
Heat Shrink Sleeve Centralizer
Grout
Anchor Nut
Bearing Plate
Smooth Sheathing
Grout
DYWIDAG THREADBAR®Centralizer
Plate Anchorage
with Nut
DYWIDAG THREADBAR® Anchors – Removable
Introduction
Removal of anchors over their full length or partial length is often a requirement where the steel of the anchor could interfere with future underground installations such as gas or water utilities� DSI´s Removable THREADBAR® Anchors offer a proven solution for projects that require anchor removal�
FOR SPECIFIC DETAILS ON REMOVABLE ANCHORS, PLEASE
CONTACT YOUR LOCAL DSI OFFICE
DYWIDAG THREADBAR® Anchor – Partially Removable
DYWIDAG THREADBAR® Anchor – Fully Removable
23
Project ReferencesProject References DYWIDAG THREADBAR® Anchors
The New Stanford Hospital: Foundations with DYWIDAG THREADBAR® Anchors, CA, USA
General Contractor Joint Venture Clark/McCarthy, USA +++ Subcontractor Condon-Johnson & Associates, Inc�, USA +++ Architect Rafael Viñoly Architects and Lee, Burkhart, Liu, Inc�, both USA +++ Structural Engineering Tuan and Robinson Structural Engineers, Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supply, technical supportDYWIDAG Products 800 DYWIDAG THREADBAR® Anchors with DCP incl� accessories, technical assistance and stressing equipment
Excavation Support and Anchoring of the Foundation of San Francisco’s Trinity Place with DYWIDAG Anchors
Owner Trinity Properties, USA +++ General Contractor Swinerton Incorporated, USA +++ Subcontractor Malcolm Drilling Company, Inc�, USA +++ Engineering Brierley Associates Corporation, USA +++ Architect Arquitectonica International Corporation, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supply DYWIDAG Products 789 double corrosion protected 57mm Ø, Grade 75 DYWIDAG THREADBAR® Anchors; 623 temporary Type 0�6" DYWIDAG Strand Anchors
24
Project References DYWIDAG THREADBAR® Anchors
Retaining Walls of Transbrasiliana Highway stabilized using DYWIDAG Bar Anchors, Brazil
Owner Governo do Estado de Goiás, Brazil +++ General Contractor Egesa Engenharia S�A�, Brazil +++ Subcontractor EMBRE - Empresa Brasileira de Engenharia e Fundações and SETE Engenharia, both Brazil +++ Engineers EMBRE - Empresa Brasileira de Engenharia e Fundações, Brazil
DSI Unit Protendidos DYWIDAG Ltda�, BrazilProtendidos Scope Production and SupplyDYWIDAG Products Supply of 37,130m of permanent, epoxy coated Ø 32mm DYWIDAG THREADBAR® Anchors with accessorie
Memorial Wall at Ground Zero inaugurated September 11th 2011, New York City, NY, USA
Owner WTCMF - World Trade Center Memorial Foundation, USA +++ General Contractor E�E� Cruz / Nicholson Construction Company,JV, USA +++ Architect Handel Architects LLP, Davis Brody Bond, LLP (Associate Architect), both USA +++ Consulting Engineers Mueser Rutledge Consulting Engineers, USA +++ Engineering WSP Cantor Seinuk, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope SupplyDYWIDAG Products 183 epoxy coated DCP Ø 66mm DYWIDAG THREADBAR® Anchors and Anchorages
25
DYWIDAG THREADBAR®
DYWI® Drill Hollow Bar
Bar Properties
THREADBAR®
Designation
Maximum THREADBAR®
Diameter
MinimumYield Stress
(fy)
NominalCross Section Area
(As)
Minimum Yield Load
(fy x As)Nominal Weight
[mm] [in] [mm] [ksi] [MPa] [in²] [mm²] [kips] [kN] [lbs/ft] [kg/m]
#6 19 0.86 22 75 517 0.44 284 33.0 147 1.50 2.23#7 22 0.99 25 75 517 0.60 387 45.0 200 2.04 3.04#8 25 1.12 28 75 517 0.79 510 59.3 264 2.67 3.97#9 29 1.26 32 75 517 1.00 645 75.0 334 3.40 5.06#10 32 1.43 36 75 517 1.27 819 95.3 424 4.30 6.40#11 36 1.61 41 75 517 1.56 1,006 117.0 520 5.31 7.90#14 43 1.86 47 80 552 2.25 1,452 180.0 801 7.65 11.38#18 57 2.50 64 80 552 4.00 2,581 320.0 1,423 13.60 20.24#20 63 2.72 69 80 552 4.91 3,168 393.0 1,748 16.70 24.85#24 75 3.18 81 75 517 7.06 4,555 529.5 2,355 24.09 35.85#28 90 3.68 94 75 517 9.62 6,207 721.5 3,209 32.79 48.80
Note: Maximum allowable temporary tension is 90% of yield load� Mill length is 60 ft (#6 through #24) and 53 ft for #28�
DYWIDAG THREADBAR® Reinforcing Steel ASTM A615 (Grade 75 & 80)
DYWIDAG THREADBAR® Reinforcing Steel ASTM A615 (Grade 100)
THREADBAR® Designation
Maximum THREADBAR®
Diameter
Minimum Yield Stress
(fy)
Nominal Cross Section Area
(As)
Minimum Yield Load
(fy x As)Nominal Weight
[mm] [in] [mm] [ksi] [MPa] [in2] [mm2] [kips] [kN] [lbs/ft] [kg/m]
#6 19 0�86 22 100 690 0�44 284 44�0 196 1�50 2�23#7 22 0�99 25 100 690 0�60 387 60�0 267 2�04 3�04#8 25 1�12 28 100 690 0�79 510 79�0 351 2�67 3�97#9 29 1�26 32 100 690 1�00 645 100�0 445 3�40 5�06#10 32 1�43 36 100 690 1�27 819 127�0 565 4�30 6�40#11 36 1�61 41 100 690 1�56 1,006 156�0 694 5�31 7�90#14 43 1�86 47 100 690 2�25 1,452 225�0 1,001 7�65 11�38#18 57 2�50 64 100 690 4�00 2,581 400�0 1,779 13�60 20�24#20 63 2�72 69 100 690 4�91 3,168 491�0 2,184 16�70 24�85
DYWIDAG THREADBAR® Prestressing Steel ASTM A722 (Grade 150)
THREADBAR®
Designation
Maximum THREADBAR®
Diameter
Minimum UltimateTensile Strength
(fu)
NominalCross Section Area
(As)
Minimum UltimateTensile Load
(fu x As)Nominal Weight
[in] [mm] [in] [mm] [ksi] [MPa] [in²] [mm²] [kips] [kN] [lbs/ft] [kg/m]
1" 26 1.25 32 150 1,034 0.85 548 127.5 567 3.01 4.481 ¼" 32 1.45 37 150 1,034 1.25 806 187.5 834 4.39 6.531 ⅜ " 36 1.63 41 150 1,034 1.58 1,019 237.0 1,054 5.56 8.271 ¾" 46 2.01 51 155 1,069 2.58 1,665 400.0 1,779 9.23 13.732 ½" 65 2.80 71 150 1,034 5.16 3,329 774.0 3,443 18.20 27.083" 75 3.15 80 150 1,034 6.85 4,419 1,027.5 4,571 24.09 35.85
Note: Maximum allowable temporary test tension shall not exceed 80% of the Minimum Ultimate Tensile Load; Mill length = 60'-0" for 1", 1¼" and 1 " Threadbars and 45'-0" for 1¾", 2½" and 3" bars� WARNING: DO NOT WELD on or near A722 prestressing bars or their anchorages�
26
A
ØW
H
ØV
B
B/2 B/2
ØC
Anchor Nut
Bearing Washer
Wedge Washer Coupler
Hex Nut
Bevel Washers
Hardware Properties
DYWIDAG THREADBAR® Reinforcing Steel Hardware Properties (Grade 75 & 80)
THREADBAR®
Designation
Hex Nut Length
H
Coupler Length
B
Coupler Outer Diameter
Ø C
Maximum Angle Compensation *
Bevel Washer Diameter
Ø V
[in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]
#6 1.43 36 3.12 79 1.22 31 17 1.78 45#7 1.71 43 3.73 95 1.41 36 19 2.26 57#8 1.84 47 4.03 102 1.59 40 17 2.56 65#9 2.30 58 5.02 128 1.79 46 18 2.88 73#10 2.56 65 5.70 145 2.02 51 19 3.20 81#11 2.89 73 6.37 162 2.25 57 18 3.27 83#14 3.55 90 7.82 199 2.65 67 18 3.25 83#18 4.23 107 9.35 238 3.50 89 18 4.00 102#20 4.85 123 10.38 264 3.86 98#24 4.10 104 9.19 233 4.75 121#28 4.80 122 10.61 270 5.38 137
* using two washers in a set� Solutions for large bars and larger angles are available – please consult your local DSI Sales Engineer Couplers and hex nuts develop the bar ultimate strength�
DYWIDAG THREADBAR® Prestressing Steel Hardware Properties (Grade 150)
THREADBAR®
Designation
Nut Length
A / H
Coupler Length
B
Coupler Outer Diameter
Ø C
Maximum Angle Compensation *
Wedge Washer Diameter
Ø W
[in] [in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]
1" 2.36 / 2.63 60 / 67 6.25 159 2.00 51 20 4.55 1161 ¼" 3.15 / 2.88 80 / 73 6.75 171 2.38 60 20 4.55 / 5.50 116 / 1401 ⅜ " 3.53 / 3.88 90 / 99 8.75 222 2.75 70 20 5.50 1401 ¾" 3.50 / 4.00 89 / 101.6 6.80 172.7 3.⅛ 79.4 20 7.26 1842 ½" – / 5.00 – / 127 10.75 273 4.50 1143" – / 5.00 – / 127 11.00 279 5.25 133
* using two washers in a set� Solutions for large bars and larger angles are available – please consult your local DSI Sales EngineerCouplers and hex nuts develop the bar ultimate tensile load�
DYWIDAG nuts and couplers develop full load of the bar nominal ultimate load�
THREADBAR®
Designation
Hex Nut Length
H
Coupler Length
B
Coupler Outer Diameter
Ø C
Maximum Angle Compensation *
Bevel Washer Diameter
Ø V
[in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]
#6 2.88 73 6.25 159 1.25 32 17 1.78 45#7 3.13 79 7.00 178 1.50 38 19 2.26 57#8 3.38 86 7.13 181 1.75 45 17 2.56 65#9 3.50 89 7.25 184 1.88 48 18 2.88 73#10 3.50 89 7.50 191 2.13 54 19 3.20 81#11 3.88 98 8.00 203 2.38 60 18 3.27 83#14 4.50 114 8.25 210 2.75 70 18 3.25 83#18 5.25 133 10.50 267 3.63 92 18 4.00 102#20 6.00 152 12.25 311 4.00 102
* using two washers in a set� Solutions for large bars and larger angles are available – please consult your local DSI Sales Engineer Couplers and hex nuts develop the bar ultimate strength�
DYWIDAG THREADBAR® Reinforcing Steel Hardware Properties (Grade 100)
27
Bearing Plate
Wedge Plate
Wedges
Greased and Hot Melt-Plastic Extruded Strand (Unbonded Length)
Post-Grout Line (optional)
Spacer
Wedge Plate
Wedges
Cover Cap (optional)
Bearing Plate with Trumpet Greased and Hot Melt-Plastic Extruded Strand (Unbonded Length)
Corrugated Plastic Sheathing
Spacer
Bare Strand (Bond Length)Post-Grout Line (optional)
End Cap
9 Strand Anchorage
Centralizer
Bare Strand (Bond Length)Grout Tube
Centralizer
Grout Tube
DYWIDAG Strand Anchors
DYWIDAG Temporary Strand Anchors
DYWIDAG Permanent Strand Anchors with DCP (Double Corrosion Protection)
Advantages and Characteristics
� Strand anchors allow for a large range of anchor capacities, as there is no theoretical limit on how many strands can be used in an anchor
� Long anchor lengths are possible without the requirement of a splice
� Most strand anchors are coiled for transport and require little storage space on site
� Utilization of high strength 270KSI strand results in low anchor weight
� The hot melt extrusion process provides a high quality, uninterrupted plastic bond breaker and additional corrosion protection
� Specialized installation and stressing equipment is available from DSI
28
Wedge Plate
Bearing Plate
G
H
Trumpet Pipe O�D�
Corrugated Sheathing O�D�
DYWIDAG Strand Anchors Properties
DYWIDAG Strand Anchors utilize 0�6" dia� 7-wire, Low Relaxation 270ksi Strand conforming to ASTM A416 (bare strand) or ASTM A882 (epoxy coated strand)�
Number of Strands
Nominal Cross Section Area (Aps)
Ultimate Strength(Fpu x Aps)
Prestressing ForceNominal Weight(bare steel only)
0.80 Fpu x Aps 0.70 Fpu x Aps 0.60 Fpu x Aps
[ea] [in2] / [mm2] [kips] / [kN] [kips] / [kN] [kips] / [kN] [kips] / [kN] [lbs/ft] / [kg/m]1 0.217 / 140 58.6 / 261 46.9 / 208 41.0 / 182 35.2 / 156 0.74 / 1.09
2 0.434 / 280 117.2 / 521 93.7 / 417 82.0 / 365 70.3 / 313 1.48 / 1.64
3 0.651 / 420 175.8 / 782 140.6 / 625 123.0 / 547 105.5 / 469 2.22 / 3.27
4 0.868 / 560 234.4 / 1,043 187.5 / 834 164.1 / 730 140.6 / 626 2.96 / 4.46
5 1.085 / 700 293.0 / 1,303 234.4 / 1,043 205.1 / 912 175.8 / 782 3.70 / 5.51
6 1.302 / 840 351.6 / 1,564 281.3 / 1,251 246.1 / 1,095 210.9 / 938 4.44 / 6.55
7 1.519 / 980 410.2 / 1,825 328.2 / 1,460 287.2 / 1,277 246.2 / 1,095 5.18 / 7.74
8 1.736 / 1,120 468.8 / 2,085 375.0 / 1,668 328.1 / 1,460 281.3 / 1,251 5.92 / 8.78
9 1.953 / 1,260 527.4 / 2,346 421.9 / 1,877 369.2 / 1,642 316.4 / 1,408 6.66 / 9.97
12 2.604 / 1,680 703.2 / 3,128 562.6 / 2,503 492.3 / 2,190 422.0 / 1,877 8.88 / 13.24
15 3.255 / 2,100 879.0 / 3,910 703.2 / 3,128 615.3 / 2,737 527.4 / 2,346 11.10 / 16.52
19 4.123 / 2,660 1,113.4 / 4,953 890.7 / 3,962 779.4 / 3,467 668.0 / 2,972 14.06 / 20.98
27 5.859 / 3,780 1,582.2 / 7,038 1,265.8 / 5,631 1,107.6 / 4,927 949.4 / 4,223 19.98 / 29.76
37 8.029 / 5,180 2,168.2 / 9,645 1,734.6 / 7,716 1,517.8 / 6,751 1,301.0 / 5,787 27.38 / 40.78
48 10.416 / 6,720 2,812.8 / 12,512 2,250.2 / 10,009 1,968.9 / 8,758 1,687.7 / 7,507 35.52 / 52.83
54 11.718 / 7,560 3,164.4 / 14,076 2,531.5 / 11,261 2,215.1 / 9,853 1,898.6 / 8,446 39.96 / 59.38
61 13.237 / 8,540 3,574.6 / 15,901 2,859.7 / 12,721 2,502.2 / 11,131 2,144.8 / 9,540 45.14 / 67.12
Aps = Area Prestressing SteelFpu = Minimum Ultimate Strength
DYWIDAG Strand Anchor Dimensions – DCP Components & Wedge Plates
Please consult your local sales office for systems exceeding 61 strands�
Max. No. of Strands*
HDPE Corrugated Sheating
Outside Diameter
Trumpet Pipe Outside
DiameterWedge Plate Dimensions
[ea]Size Des.
[in] [mm] [in] [mm]Ø G [in]
Ø G [mm]
H [in] H [mm]
3 2" 2�44 62 4�50 114 4�69 119 1�80 46
4 2�5" 2�92 74 4�50 114 4�69 119 1�80 46
6 2�5" 2�92 74 4�50 114 5�61 142 2�40 61
7 3" 3�60 91 4�50 114 5�61 142 2�40 61
9 3" 3�60 91 5�63 143 5�51 140 1�69 43
12 4" 4�60 117 5�63 143 6�30 160 1�69 43
15 4" 4�60 117 6�63 168 7�09 180 1�97 50
18 4" 4�60 117 8�63 219 7�87 200 2�17 55
24 5" 5�85 149 8�63 219 9�45 240 2�95 75
27 6" 6�80 173 8�63 219 9�45 240 2�95 75
* based on the use of a single 0�5" ID x 0�75" OD internal grout tube�
Please consult your local sales office for systems exceeding 27 strands�Bearing plates sizes are dependent on project specific conditions� DSI staff can assist with sizing of bearing plates�
29
Project References DYWIDAG Strand Anchors
DYWIDAG Strand Anchors prevent Settlements at a large Retail Center, AL, USA
General Contractor Hayward Baker, Inc�, USA +++ Engineering Burns Cooley Dennis, Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supplyDYWIDAG Products 80 permanent 12-0�6" DYWIDAG Strand Anchors; 6 DYNA Force® Sensors; rental of equipment
Stabilization of a dangerous Landslide at California’s White Point Nature Preserve near Los Angeles, CA, USA
General Contractor Hayward Baker Inc�, USA +++ Subcontractor Hayward Baker Inc�, USA +++ Geotechnical Consulting Shannon & Wilson, Inc�, USA
DSI Unit DYWIDAG-Systems International USA, Inc�, BU Geotechnics, USADSI Scope Production, supply, technical supportDYWIDAG Products 18 permanent Type 6-0�6" DYWIDAG Strand Anchors, 14 DYNA Force® Sensors with readout unit and multiplexers, tensioning equipment and uncoilers
30
Project References DYWIDAG Strand Anchors
Active Dam Reinforcement with DYWIDAG Multistrand Anchors, NY, USA
Owner Central Hudson Gas & Electric, Poughkeepsie, NY, USA +++ General Contractor Construction Drilling Inc�, North Adams, MA, USA +++ Consulting DTA Engineers of New York, Inc�, USA
DSI Unit DYWIDAG-Systems International USA Inc�, BU Geotechnics, USA DSI Scope Production, supply DYWIDAG Products Epoxy coated DYWIDAG Strand Anchors with accessories; rental of equipment
Golden Gate Bridge Seismic Retrofit using DYWIDAG Geotechnical Post-Tensioning Systems, CA, USA
Owner Golden Gate Bridge, Highway and Transportation District, San Francisco, CA, USA +++ Engineer Jacobs Civil Inc� in association with Thomas Jee Associates, Inc�, CA, USA +++ General Contractor Shimmick Construction Company, Inc�/Obayashi Corporation, a Joint Venture, San Francisco, CA, USA +++ Subcontractor and Tiedown Anchor Installer Drill Tech Drilling and Shoring, Antioch, CA, USA
DSI Unit DYWIDAG-Systems International USA Inc�, Long Beach, Western Division USA DSI Scope Supply, installation, stressing and groutingDYWIDAG Products 110t 37-Ø 15�2 mm multistrand tendons, 11t Ø 32 and 36mm THREADBAR® system; supply of 145t pre-assemb-led Ø 15�2 mm epoxy coated strand tiedown anchors manufactured as follows: 32 DYWIDAG Strand Anchors with 7 strands, 24 anchors with 15 strands, 24 anchors with 19 strands and 56 anchors with 45 strands
31
32
33
Pho
to re
prin
ted
cou
rtes
y of
Jin
Lee
Pho
togr
aphy
, US
A
9/11 Memorial & Museum
On May 15th 2014, the 9/11 Memorial & Museum was opened to commemorate the terrorist attacks that took place on September 11th 2001� The large Foundation Hall is at the center of the museum� It displays a 19 x 20m (62 x 64ft) large wall tied back by double corrosion protected strand anchors that were produced and supplied by DYWIDAG-Systems International’s plant in Toughkenamon, PA�
Vertical UncoilerHorizontal Uncoiler “Lazy Susan”
1,500 kN Jack (2-7 Strands) equipped with EZ Chair
Grout Swivel
Hoz 3000 Jack “The Torpedo” (max� 12 Strands – 20" stroke) equipped with EZ Chair
TENSA 3000 Bar Jack(1¾" Gr� 150 bars)
110 MP Bar Jack(1", 1¼" and 1 " Gr� 150 bars)
Anchor Installation Equipment
Uncoiling equipment is utilized to ensure efficient and safe installation of strand anchors while minimizing the risk of damage to the corrosion protection system� Various manual and motorized styles of uncoilers are available to meet project specific needs�
Geotechnical Equipment
Stressing Equipment
DSI has a large inventory of stressing equipment that enables our customers to test and lock off bar and strand tendons of any size� The stressing jacks are complemented by stressing chairs, pulling heads and hydraulic pumps for safe and efficient stressing operations�Customized equipment has been provided for many jobs with difficult access or for high capacity anchors� Our in house engineering staff is well suited to work with you on your job specific details and requirements�
Hollow Bar Grout Swivels
Grout Swivels are used for a simultaneous drilling and grouting operation� The Swivel allows for injection of grout through the bore of a rotating DYWI® Drill Hollow Bar into the hole� The unit comprises of a heat treated shaft (to withstand the impact energy from the hammer drive) and a housing into which the grout is pumped� Inlet ports within the shaft allow grout to be pumped into the bore of the bar�
34
35
DYWIDAG-SystemsInternational USA Inc.
320 Marmon DriveBolingbrook, IL 60440Phone (630) 739-1100
Toughkenamon, PAPhone (610) 268-2221
McLean, VAPhone (302) 293-2377
Pompano Beach, FLPhone (954) 532-1326
Mansfield, TXPhone (817) 473-6161
Long Beach, CAPhone (562) 531-6161
Tucker, GAPhone (770) 491-3790
Kent, WAPhone (253) 859-9995
E-Mail [email protected]
DSI Canada Civil Ltd.
Eastern Division37 Cardico DriveGormley, ON L0H1G0Phone (905) 888-8988
St. Bruno, QCPhone (450) 653-0935
E-Mail [email protected]
Western Division19433 96th Av. Suite 103Surrey, BC V4N 4C4Phone (604) 888-8818
Calgary, ABPhone (403) 291-4414
E-Mail [email protected]
A R G E N T I N A
A U S T R A L I A
A U S T R I A
B E L G I U M
B O S N I A A N D H E R Z E G O V I N A
B R A Z I L
C A N A D A
C H I L E
C H I N A
C O L O M B I A
C O S TA R I C A
C R O AT I A
C Z E C H R E P U B L I C
D E A N M A R K
E G Y P T
E S T O N I A
F I N L A N D
F R A N C E
G E R M A N Y
G R E E C E
G U AT E M A L A
H O N D U R A S
H O N G K O N G
I N D I A
I N D O N E S I A
I TA LY
I R A N
J A PA N
K O R E A
L E B A N O N
L U X E M B O U R G
M A L AY S I A
M E X I C O
N E T H E R L A N D S
N I G E R I A
N O R W AY
O M A N
PA N A M A
PA R A G U AY
P E R U
P O L A N D
P O R T U G A L
Q ATA R
R U S S I A
S A U D I A R A B I A
S I N G A P O R E
S O U T H A F R I C A
S PA I N
S W E D E N
S W I T Z E R L A N D
TA I W A N
T H A I L A N D
T U R K E Y
U N I T E D A R A B E M I R AT E S
U N I T E D K I N G D O M
U R U G U AY
U S A
V E N E Z U E L A
www.dsiamerica.comwww.dsicanada.ca 04
170-
1US
/08.
16-w
eb s
c
Please note: This brochure serves basic information purposes only. Technical data and information provided herein shall be considered non-binding and may be subject to change without notice. We do not assume any liability for losses or damages attributed to the use of this technical data and any improper use of our products. Should you require further information on particular products, please do not hesitate to contact us.