Four-wheel Electric Counterbalanced Lift TrucksE1.502.00XMS

1 500 2 000 kg

STRONG PARTNERS. TOUGH TRUCKS.

Forks:E1.50-2.00XMS: 40 x 80 x 1 000

to 1 200 mm long

Fork spacing:Inside to inside, minimum: 50 mmOutside to outside, maximum: 865 mm

E1.50XM, E1.75XM, E2.00XMS

Equipment and weight:Weights (line 2.1) are based on the following specifications:Complete truck with 3 330 mm Vista 2-stage limited freelift mast, 910 mm hook type carriage with load backrestand 1 000 mm forks. Overhead guard and cushion orpneumatic-shaped solid tyres.

Specification data is based on VDI 2198

Load centre (mm)

Rat

ed lo

ad (k

g)

E2.00XMSE1.75XME1.50XM

Load centre

Distance from front of forks to centre of

gravity of load.

Rated load

Based on vertical masts up to 4 050 mm

to top of forks.

= Centre of gravity of unladen truck

Ast = wa + x + l6 + a (see line 4.33 & 4.34)

a = Minimum operating clearance

(V.D.I. standard = 200 mm BITA recommendation = 300 mm)

l6 = Load length

*Standard tread shown-see 3.6 for optional tread

NOTE:

Specifications are affected by the condition

of the vehicle and how it is equipped, as well

as the nature and condition of the operating

area. If these specifications are critical, the

proposed application should be discussed

with your dealer.

Bottom of forks

Without load backrest

Q h6 subject to +/- 5 mm tolerance, add 63 mm for raised guard

Low rider fitted add 37 mm for full suspension seat

X Stacking aisle width (line 4.33 & 4.34) is based on the V.D.I.

standard calculation as shown on

illustration. The British Industrial Truck

Association recommends the

addition of 100 mm to the total

clearance (dimension a) for extra

operating margin at the rear of the

truck.

Gradeability figures (lines 5.7 & 5.8)

are provided for comparison of

tractive performance, but are not

intended to endorse the operation

of the vehicle on the stated inclines.

Follow instructions in the operating

manual regarding operation on

inclines.

O Subtract 32 mm without load backrest Variable

Tables key:

Add 650 mm with load backrest extension

P Deduct 650 mm with load backrest extension

Wide tread required (Standard tread may be supplied at

reduced capacity)

Notice

Care must be exercised when handling

elevated loads. When the carriage

and/or load is elevated, truck stability

is reduced. It is important that mast tilt

in either direction be kept to a

minimum when loads are elevated.

Operators must be trained and adhere

to the instructions contained in the

Operating Manual.

Safety:

This truck conforms to the current EU requirements.

Hyster products are subject to change without notice.

Lift trucks illustrated may feature optional equipment.

Mast and Capacity Information

The rated capacities shown are for masts in a vertical position on trucks equipped with standard or sideshift carriage and nominal length forks. Masts above themaximum fork heights shown in the mast table are classified as high lift and, depending on the tyre/tread configuration may require reduced capacity, restricted back tiltor wide tread.

Values shown are for standard equipment. When using non-standard equipment these values may change. Please contact your Hyster dealer for information.

Product Features

Application matched performance and battery shift life

Hyster ACX system offers extended shift life or extra AC performance options to suit each application.

AC technology on both traction and hydraulics for reliable, positive performance.

Brushless DC steering motor.

Compact dimensions and extraordinary manoeuvrability offer tight aisle widths.

Advanced ergonomic features to inspire productivity

Hydraulic control/seat choices.

Q Standard fully adjustable semi-suspension seat with integral armrest. With low effort, soft touch, manualhydraulic levers.

Q Optional e-hydraulic seat with TouchPoint mini-levers provide ultimate fingertip precision control.

Q Optional e-hydraulic seat with TouchControl joystick. Especially suited to intensive applications where hydraulic operation is frequent and accurate/delicate hydraulic control is required.

Convenient step and handgrip for ease of access.

Demand Sense Steering.

Monotrol pedal (optional).

Clear view dash display with LCD indicators.

4 pre-programmed performance modes.

Q Pin codes (optional) can be allocated to individual drivers allowing them access only to the performancelevel suited to their ability and experience.

Battery discharge indicator with lift interrupt.

Full range of Vista masts. 2 stage limited free lift, 2 or 3 stage full free lift with hydraulic mast cushioning fordependable handling of fragile loads.

Offering excellent visibility with smooth, low noise operation.

Dependability and low cost of operation

Extended battery shift life.

1 000 hour service intervals on most major components*.

100% brushless AC motors.

Auto regenerative braking.

On board diagnostics for early warning of maintenance requirements.

One piece frame, designed using FEA** technology, and robust steer axle design for proven durability.

* Subject to applications survey

**Finite Element Analysis

Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England.

Tel: +44 (0) 1252 810261 Fax: +44 (0) 1252 770702

Email: infoeurope@hyster.com Website: www.hyster.com/europe

A division of NACCO Materials Handling Limited.

03/09/TLC Printed in EnglandForm No. 901028/3

Hyster, , Vista and Monotrol are registered trademarks of Hyster Company in the United States and in certain other countries.TM, FortensTM, Pacesetter VSMTM, DuraMatchTM, DuraMatch PlusTM, TouchPointTM, TouchControlTM, EZXchange & HSMTM are trademarks

of Hyster Company in the United States and in certain other countries. TM

Strong Partners, Tough Trucks,

for Demanding Operations Everywhere.

Hyster supplies a complete product range,

including Warehouse trucks, IC and Electric

Counterbalanced trucks, Container Handlers

and Reach Stackers.

Hyster is committed to being much more than a

lift truck supplier. Our aim is to offer a complete

partnership capable of responding to the full

spectrum of materials handling issues:

Whether you need professional consultancy on

your fleet management, fully qualified service

support, or reliable parts supply, you can

depend on Hyster. Our network of highly trained

dealers provides expert, responsive local

support.

They can offer cost-effective finance packages

and introduce effectively managed maintenance

programmes to ensure that you get the best

possible value. Our business is dealing with

your materials handling needs so you can focus

on the success of your business today and in

the future.