E3 ODE PRO Installation Manual v1.23

The E3 ODE PRO is the best ODE for PS3 in the world . NO restart, No eject, easy toupgrade and easy to use.

E3 ODE PRO support all slim console include 2XXXX, 3XXXX and 4XXXX .

We recommend user upgrade your PS3 console to latest firmware before installE3 ODE PRO

Some user want change PS3 inner harddisk, We recommend user change PS3hardisk before install E3 ODE PRO

Installation of the E3 ODE PRO is quick and convenient.

The E3 ODE RPO pack includes:1 x E3 ODE PRO Main board1 x SOLDER BOARD1 x USB STICK1 x each of the following FFC cables:Cable Types

Type A FFC LVDS Cable, 24 Positions, Opposite side contact, 300mmType B FFC LVDS Cable, 7 Positions, Opposite side contact, 400mmType C FFC LVDS Cable, 6 Positions, Same side contact, 200mmType D FFC LVDS Cable, 6 Positions, Opposite side contact, 200mm1 x power cables

Installation on SLIM and SUPER SLIM models (CECH 25XX. CECH 3XXX andCECH 4XXX)

Carefully remove the resistors in the SATA signals area highlighted in the red circle inthe picturesbelow, for your respective console model, using a fine tip low power soldering iron.Please takeabsolute care when doing so, as these traces are essential for the console and ODEto function:

25XX JSD-001 Motherboard shown here:

25XX JTP-001 Motherboard shown here:

3XXX KTE-001 Motherboard shown here:

4XXX MPX-001 Motherboard shown here:

4XXX MSX-001 Motherboard shown here:

Credit to PS3 Dev Wiki for Motherboard images shown.

Once you have removed the resistors from the SATA lines and placed the solderboard on top of your Motherboard in alignment with solder pads, it should looksomething like this:

Once you have soldered the solder board to your console Motherboard, it should looksimilar to the image below:25xx/3xxx shown here:

4xxx shown here:

Then insert the 24 pin FFC LVDS cable (Marked as F the table above) between solderboard on the ODE and 24 pin FFC LVDS connector on the solder board which yousoldered to the console motherboard.25xx/3xxx shown here:

4xxx shown here:

Route the FFC cable out of the shielding as shown:25xx/3xxx shown here:

4xxx shown here:

Relevant connector on E3 ODE PRO shown:

Disconnect the power cable between the console power supply and the consolemotherboard. Replace the cable with the correct type which has connector matchingthat of your console. Insert the 4 pin low profile connector to your E3 ODE PRO boardconnecter marked power as shown here(note that the connector is top down press fit, not slide in) Kindly, note carefully theorientation and direction of the cable, failure to do so could cause damage ormalfunction:

25xx/3xxx shown:

4xxx shown:

Disconnect the 6PIN eject cable between the console motherboard and the BD drive.Replace the cable with the correct type which has connector matching that of yourconsole.

25xx/3xxx shown and install on consolePlease note don’t mix the text 6PIN cable and NO text 6PIN cable

4xxxx shown and install on consolePlease note don’t mix the text 6PIN cable and NO text 6PIN cable

On other console which hasn’t 6PIN connector like 25xx, user needn’t connect those6PIN cable.

You can now connect the 7PIN FFC from E3 mainboard to E3 USB STICK

The E3 ODE PRO should be positioned inside the console as shown(CECH25XX/3XXX):

Please adhere the double sided adhesive E3 ODE PRO between metal casing ofdrive andbottom of E3 ODE PRO main board to act as an insulating shield.

The E3 ODE PRO should be positioned inside the console as shown (CECH4XXX):

You can now re-assemble your console and get ready to play games.