EAGLE - Noodlez.org Courses PDF Student Guides... · loading comsec variable with ancd 4 loading...

EAGLE UNIVERSITY Radio Quick Reference Guide

TABLE OF CONTENTS

AN/PRC-119 PAGE LOS FIX FREQUENCY PROGRAMMING 4 LOADING COMSEC VARIABLE WITH ANCD 4 LOADING COMSEC VARIABLE WITH SKL 5 LOADING SINCGARS FH LOADSET WITH A CYZ-10 5

LOADING SINCG ARS FH LOADSET WITH AN SKL 6 CHANGE NET ID 6 MANUALLY ENTER TIME 6 AN/PRC-148 LOADING COMSEC VARIABLE WITH A CYZ-1 8 0 LOADING COMSEC VARIABLE WITH AN SKL 8 LOS FIX FREQUENCY PROGRAMMING 9 LOADING SINCGARS FH LOADSET WITH A CYZ-10 9 LOADING SINCGARS FH LOADSET WITH A SKL 10 SINCGARS PROGRAMMING 10 MANUALLY ENTER TIME 11 AN/PRC-152 LOADING COMSEC VARIABLE WITH A CYZ-10 13 LOADING COMSEC VARIABLE WITH AN SKL 13 FIX FREQUENCY PROGRAMMING (VULOS) 14 LOADING SINCGARS FH LOADSET WITH A CYZ-10 15 LOADING SINCGARS FH LOADSET WITH AN SKL 15 SINCGARS PROGRAMMING 16 MANUALLY ENTER TIME 16 SATCOM PROGRAMMING 17 AN/PRC-150 CONFIGURATION PROGRAMMING 19 PROGRAMMING CHANNEL PRESETS 19 LOADING COMSEC INTO THE RADIO with ANCD 19 LOADING COMSEC INTO THE RADIO with SKL 20 ASSIGNING COMSEC TO CHANNEL 20 PROGRAMMING PRESETS (MANUAL) 20 PROGRAMMING PRESETS (SYSTEM) 21 PROGRAMMING ALE 22

1


AN/PRC-117 LOS FIX FREQUENCY PROGRAMMING 24 TACSAT PROGRAMING 25 LOADING COMSEC VARIABLE WITH A CYZ-10 26 LOADING COMSEC VARIABLE WITH AN SKL 26 LOADING SINCGARS FH LOADSET WITH A CYZ-10 27 LOADING SINCGARS FH LOADSET WITH SKL 27 SINCGARS HOPPING (ECCM) PROGRAMMING 28 DAMA NET PROGRAMMING 29 DAMA PORT CONFIGURATION PROGRAMMING 29 DAMA DESTINATION PROGRAMMING 30

2


AN/PRC-119

3


LOS FIX FREQUENCY PROGRAMMING 1. Set the radio the following: a. COMSEC to PT b. MODE to SC c. FUNCTION SWITCH to LD d. CHANNEL to be programmed. (0-7) 2. Press FREQ 3. Press CLR 4. Enter the 5 digit frequency 5. Press STO 6. Select the next channel and repeat steps 2-5. 7. Place FUNCTION SWITCH to SQ ON.

LOADING COMSEC VARIABLE WITH ANCD

1. Set the radio the following: a. COMSEC to CT b. MODE to SC c. FUNCTION SWITCH to LD 2. Connect FILL Device to the Audio/Fill Port (J2) of the radio. 3. Turn on ANCD 4. Select APPL, press ENT 5. Select RADIO, press ENT 6. Select COMSEC, press ENT 7. Select LD, press ENT 8. Select TEK, press ENT 9. SELECT KEY is highlighted. P DN until the correct key is displayed. Press ENT, XMT

appears in the bottom right corner 10. Select QUIT, press ENT 11. Connect ANCD to radio, press ENT on ANCD. 12. ANCD displays Sending TEK xxxx followed by Press [LOAD] on RT 13. When the FILL Device instructs, press the LOAD button on the radio. 14. Press STO 15. Press the desired position (1-6) 16. Select another key on the FILL Device and repeat steps 4-6. 17. Turn off and disconnect Fill Device from the radio. 18. Place FUNCTION SWITCH to SQ ON.

4


LOADING COMSEC VARIABLE WITH SKL

1. Set the radio the following: a. COMSEC to CT b. MODE to SC c. FUNCTION SWITCH to LD 2. Connect FILL Device to the Audio/Fill Port (J2) of the radio. 3. On the SKL, select the Keys tab. 4. Select a key then the Load icon in the upper right. 5. Use DS-102 protocol, KYK13 activation mode, click OK. 6. At Ready to Send Key screen, click OK. 7. The Status screen will display Press INITIATE Button. 8. When the FILL Device instructs, press the LOAD button on the radio. 9. Press STO 10. Press the desired position (1-6) 11. Select another key on the FILL Device and repeat steps 4-6. 12. Turn off and disconnect Fill Device from the radio. 13. Place FUNCTION SWITCH to SQ ON.

LOADING SINCGARS FH LOADSET WITH A CYZ-10 1. Set the radio the following: a. COMSEC to CT b. MODE to FH

c. FUNCTION SWITCH to LD 2. Connect FILL Device to the Audio/Fill Port (J2) of the radio. 3. On CYZ-10, load Radio application. 4. On CYZ-10, select Send. Press ENT. 5. On CYZ-10, select Send to: Radio. Press ENT. 6. On CYZ-10, select iCom. Press ENT. 7. On CYZ-10, follow on-screen steps until asked whether to include time. 8. On CYZ-10, select Include Time – Y/N as required. Press ENT 9. CYZ-10 will display Press LOAD on RT. 10. On the Radio, press the LOAD button. 11. The process will take approximately 1 minute. 12. CYZ-10 will display ICOM TRANSFER SUCCESSFUL when complete. 13. Turn off and disconnect Fill Device from the radio. 14. Place FUNCTION SWITCH to SQ ON.

5


LOADING SINCGARS FH LOADSET WITH AN SKL

1. Set the radio the following: a. COMSEC to CT b. MODE to FH

c. FUNCTION SWITCH to LD 2. Connect FILL Device to the Audio/Fill Port (J2) of the radio. 3. On SKL, select Eqs Tab. 4. On SKL, select RT-1523. 5. On SKL, select the LOAD icon in the upper right. 6. On SKL, select ICOM Transfer & check Include Time if needed. Click OK. 7. On SKL, at the Connect To screen, select Next>> 8. On SKL, at the Profiles screen, select Send. SKL displays Press LOAD Button. 9. On radio, press LOAD button. Observe progress on SKL. Transfer takes about 20 seconds.

CHANGE NET ID 1. Set the radio the following: a. COMSEC to CT b. MODE to FH

c. FUNCTION SWITCH to LD d. CHANNEL to be programmed. (1-6)

2. Press FREQ 3. Press CLR 4. Enter the 3 digit Net ID 5. Press STO 6. Select the next channel and repeat steps 2-5. 7. Place FUNCTION SWITCH to SQ ON.

MANUALLY ENTER TIME 1. Set the radio the following: a. COMSEC to CT b. MODE to FH

c. FUNCTION SWITCH to LD 2. Press TIME 3. Press CLR 4. Enter the 2 digit Julian Date 5. Press STO 6. Press TIME 7. Press CLR 8. Enter the Hour and minute. (Set the minute ahead of GPS time) 9. Press STO when time on radio matches GPS time. 10. Place FUNCTION SWITCH to SQ ON.

6


AN/PRC-148

7


LOADING COMSEC VARIABLE WITH A CYZ-10

1. Press ALT/MODE at the same time 2. Select KEY FILL and press ENT 3. Select DS102, press ENT twice 4. Turn on ANCD 5. Select APPL, press ENT 6. Select RADIO, press ENT 7. Select COMSEC, press ENT 8. Select LD, press ENT 9. Select TEK, press ENT 10. SELECT KEY is highlighted. P DN until the correct key is displayed. Press ENT, XMT

appears in the bottom right corner 11. Select QUIT, press ENT 12. Connect ANCD to radio, press ENT on ANCD. 13. ANCD displays Sending TEK xxxx followed by Press [LOAD] on RT 14. On radio, select TEK 1, press the PTT BUTTON to load 15. The ANCD will read 1 KEYS TRANSFERRED 16. Radio displays TRANSFER SUCCESSFUL, TEK01 will change to TEK02. 17. Select another key and load TEK02 or press ESC.

LOADING COMSEC VARIABLE WITH AN SKL

1. Press ALT/MODE at the same time 2. Select KEY FILL and press ENT 3. Select DS102, press ENT twice 4. On the SKL, select the Keys tab. 5. Select a key then the Load icon in the upper right. 6. Use DS-102 protocol, KYK13 activation mode, click OK. 7. At Ready to Send Key screen, click OK. 8. On the Status screen when it states to Press INITIATE Button, press the PTT Button. 9. The SKL will state Operation Successful if there were no problems. 10. On radio, select TEK 1, press the PTT BUTTON to load 11. The SKL will read 1 KEYS TRANSFERRED 12. Radio displays TRANSFER SUCCESSFUL, TEK01 will change to TEK02. 13. Select another key and load TEK02 or press ESC.

8


LOS FIX FREQUENCY PROGRAMMING

1. Press ALT/MODE at the same time 2. Select PROGRAM and press ENT 3. Select CHANNEL and press ENT 4. Select the Channel (001 - 256) 5. Select PLAIN or SECURE 6. Name the Channel (7 digits max) 7. Skip Power, set it last. 8. Select the Mode (BASIC) 9. Set the RX frequency. TX matches the RX automatically. 10. If below 90 MHz set Squelch to 150. (e.g. R=150.0 T=150.0). Above 90 MHZ leave

Squelch at 0. 11. Set Modulation (FM, AM, NB, etc) 12. Set the Data Rate if needed. 13. Select the COMSEC position. (TEK01) 14. RPTR, FADE, PHASE, & SQLCH set as needed. (Default is normal) 15. Press ESC to select the next channel or ESC out of programming.

LOADING SINCGARS FH LOADSET WITH A CYZ-10

1. Press ALT/MODE at same time 2. Select KEY FILL by pressing up button once then press ENT 3. Select MODE23 then press ENT 4. CONNECT MODE23 DEVICE will appear 5. Turn on ANCD 6. Select APPL, press ENT 7. Select RADIO, press ENT 8. Select SEND, press ENT 9. SEND TO: select RADIO, press ENT 10. SELECT: select ICOM, press ENT 11. CONNECT TO RT AUD/FILL CONNECTOR appears. 12. Press down arrow key to continue to next page 13. DO YOU WANT TO INCLUDE TIME? Select Y/N as required and press ENT 14. Press PTT button on radio, loading appears. Wait until finished 15. ANCD displays TRANSFER SUCCESSFUL, disconnect ANCD.

9


LOADING SINCGARS FH LOADSET WITH A SKL

MODE 2/3 will not load COMSEC with the LOADSET using an SKL! 1. Press ALT/MODE at same time 2. Select KEY FILL by pressing up button once then press ENT 3. Select MODE23 then press ENT. The radio displays CONNECT MODE23 DEVICE PTT TO LOAD 4. On SKL, select the Eqs Tab 5. Expand RT-1523 & select any location under RT-1523. (H1 for example) 6. Select File, Transmit, Load Selected Locations. 7. In the Load Selected Locations screen, select H0 to H6 (7 items), click OK. 8. Select ICOM Transfer, click OK; Next; then Send. 9. Press the PTT button when the SKL states Press LOAD Button. 10. SKL displays that it is sending 5 empty TEKs, 1 empty KEK, 6 Hopsets, & 8 empty Lockouts. When complete it states Re-load equipment? Select NO. 11. The radio will display LOADING… during step 10. After the SKL is finished, the radio displays INITIALIZING CRYPTO CHANNELS PLEASE WAIT, then returns to the KEYFILL menu. 12. The COMSEC keys will have to be loaded one at a time. Refer to LOADING COMSEC VARIABLE WITH AN SKL.

SINCGARS PROGRAMMING

1. Press ALT/MODE at the same time 2. Select PROGRAM and press ENT 3. Select CHANNEL and press ENT 4. Select the Channel (e.g. CH=001) 5. Select SECURE 6. Name the Channel (7 digits max) 7. Skip Power, set it last. 8. Select the Mode (SINCGARS) 9. Select the SINCGARS slot (1-6), CUE, or MAN. 10. Set ECCM to FH or SC. 11. FX=, enter a SC frequency if required. Ignore this is ECCM is set to FH. 12. SINCGARS is always FM, set the Data Rate if required. 13. Select the COMSEC position. (TEK01) 14. RPTR, FADE, PHASE, & SQLCH set as needed. (Default is normal) 15. Press ESC to select the next channel or ESC out of programming.

10


MANUALLY ENTER TIME

1. Press ALT/MODE at the same time 2. Select PROGRAM then press ENT 3. Select GLOBAL then press ENT 4. Select SET CLOCK then press ENT 5. Change the day to the correct Julian day. 6. Change the Hours to the correct ZULU hour 7. Change the Minutes to one minute ahead of ZULU time. 8. Press ENT when time on radio matches GPS time. 9. To view the clock press ESC 3 times, select STATUS, then CLOCK.

11


AN/PRC-152

12


LOADING COMSEC VARIABLE WITH A CYZ-10

1. Turn radio on; rotate cipher switch to LD 2. Select FILL 3. Select VULOS for WAVEFORM FOR KEY 4. Select the correct FILL DEVICE (KYK-13). Radio displays PRESS ENT TO INITIATE

FILL 5. Turn on ANCD 6. Select APPL, press ENT 7. Select RADIO, press ENT 8. Select COMSEC, press ENT 9. Select LD, press ENT 10. Select TEK, press ENT 11. SELECT KEY is highlighted. P DN until the correct key is displayed. Press ENT, XMT

appears in the bottom right corner 12. Select QUIT, press ENT 13. Connect ANCD to radio, press ENT on ANCD. 14. ANCD displays Sending TEK xxxx followed by Press [LOAD] on RT 15. Press ENT on radio to initiate Fill. 16. Select the CRYPTO MODE (VINSON, ANDVT, etc) 17. Select the KEY TYPE (TEK) and KEY NUMBER (01) 18. Select the CLASSIFICATION (SECRET) 19. LOAD ANOTHER KEY (NO/YES) 20. Disconnect fill device and rotate cipher switch to CT when done

LOADING COMSEC VARIABLE WITH AN SKL

1. Turn radio on; rotate cipher switch to LD 2. Select FILL 3. Select VULOS for WAVEFORM FOR KEY 4. Select the correct FILL DEVICE (PYQ-10 [SKL DS-102]). Radio displays PRESS ENT TO INITIATE FILL 5. On SKL, select Keys Tab, select the correct key and select the LOAD icon in the upper right. 6. On SKL, select DS-102 for both Protocol: & Activate Mode: click OK. 7. At Ready to Send Key screen, click OK. 8. On the Status screen when it states to Press INITIATE Button; 9. Press ENT on radio 10. Select the CRYPTO MODE (VINSON, ANDVT, etc) 11. Select the KEY TYPE (TEK) and KEY NUMBER (01) 12. Select the CLASSIFICATION (SECRET) 13. LOAD ANOTHER KEY (NO/YES) 14. Disconnect fill device and rotate cipher switch to CT when done

13


FIX FREQUENCY PROGRAMMING (VULOS)

1. Press PGM 2. Select SYSTEM PRESETS 3. Select SYSTEM PRESET CONFIG 4. Select a SYSTEM PRESET NUMBER (01 – 99) 5. Enter a PRESET DESCRIPTION 6. Select VULOS for PRESET WAVEFORM 7. Select GENERAL CONFIG

a. Enter a name for PRESET NAME b. Select LOS for PRESET TYPE

8. Select FREQUENCY a. Enter the RX FREQUENCY b. NO for RECEIVE ONLY c. Enter TX FREQUENCY or select USE RX FREQ

9. Select COMSEC a. Select the CRYPTO MODE (VINSON) b. Select the CRYPTO KEY

10. Select TRAFFIC a. Select the TRAFFIC MODE (Voice, Data). VOICE MODE cannot be edited b. Select MODULATION TYPE (AM / FM) c. Select FM DEVIATION

11. Select TX POWER a. Select the TX POWER LEVEL

12. Select SQUELCH a. Select SQUELCH TYPE (TONE, NOISE, etc)

13. Select EXIT 14. Press PGM to exit to operational screen.

14



1. Rotate cipher switch to LD 2. Select FILL 3. Select SINCGARS for WAVEFORM FOR KEY 4. Select CYZ-10 [MODE2/3] for FILL DEVICE. Radio displays INITIATE FILL AT FILL DEVICE. 5. On CYZ-10, load Radio application. 6. On CYZ-10, select Send. Press ENTR. 7. On CYZ-10, select Send to: Radio. Press ENTR. 8. On CYZ-10, select iCom. Press ENTR. 9. On CYZ-10, follow on-screen steps until asked whether to include time. 10. On CYZ-10, select Include Time – Y/N as required. Press ENTR 11. The Mode 2/3 fill process will begin and will take approximately 1 minute. 12. On the Radio, select CLASSIFICATION (SECRET). Radio displays # of TEKs loaded, Press ENT. 13. LOAD ANOTHER KEY (NO/YES) 14. Disconnect fill device and rotate cipher switch to CT when done

LOADING SINCGARS FH LOADSET WITH AN SKL

1. Rotate cipher switch to LD 2. Select FILL 3. Select SINCGARS for WAVEFORM FOR KEY 4. Select PYQ-10 [SKL MODE2/3] for FILL DEVICE. Radio displays INITIATE FILL AT FILL DEVICE. 5. On SKL, select Eqs Tab. 6. On SKL, select RT-1523. 7. On SKL, select the LOAD icon in the upper right. 8. On SKL, select ICOM Transfer & check Include Time if needed. Click OK. 9. On SKL, at the Connect To screen, select Next>> 10. On SKL, at the Profiles screen, select Send 11. The Mode 2/3 fill process will begin and will take approximately 20 seconds. 12. On the Radio, select CLASSIFICATION (SECRET). Radio displays # of TEKs loaded, Press ENT 13. LOAD ANOTHER KEY (NO/YES) 14. Disconnect fill device and rotate cipher switch to CT when done

15


SINCGARS PROGRAMMING

1. Press PGM 2. Select SYSTEM PRESETS 3. Select SYSTEM PRESET CONFIG 4. Select a SYSTEM PRESET NUMBER (01 – 99) 5. Enter a PRESET DESCRIPTION 6. Select SINCGARS FOR PRESET WAVEFORM 7. Select FREQUENCY HOPPING for OPMODE. 8. Enter a name for PRESET NAME 9. Select a CRYPTO KEY 10. Select the TX POWER LEVEL 11. Select the TRAFFIC MODE (VOICE) 12. Select the HOPSET COMPARTMENT (01-25) 13. Enter a SC FREQUENCY (if needed) 14. Set SC SQUELCH TYPE to TONE 15. Press CLR then select SINCGARS CONFIG 16. Select MASTER/MEMBER to set the SINCGARS RADIO TYPE 17. Select CUE CONFIGURATION to set the CUE FREQUENCY, CUE SQUELCH TYPE, & ENABLE CUE NOTIFY 18. Select HOPSET/LOCKOUT then COPY HOPSET to change the NET ID. The Net ID can also be changed at the main operational screen by pressing the left or right arrow until the Net ID is highlighted. Change the 3-digit ID and press ENT.

MANUALLY ENTER TIME

1. From the main operational screen, select a SINCGARS Preset 2. Press OPT (#7) key 3. Select SINCGARS OPTIONS 4. Select SINCGARS GTOD 5. Select USER ENTRY 6. Press ENT to modify time 7. Enter the Julian Date and TIME. Change the Minutes to one minute ahead of ZULU time. 8. Press ENT when time on radio matches GPS time

16


SATCOM PROGRAMMING

1. Press PGM 2. Select SYSTEM PRESETS 3. Select SYSTEM PRESET CONFIG 4. Select a SYSTEM PRESET NUMBER (01 – 99) 5. Enter a PRESET DESCRIPTION 6. Select VULOS FOR PRESET WAVEFORM 7. Select GENERAL CONFIG

a. Enter a name for PRESET NAME b. Select SATCOM for PRESET TYPE

8. Select FREQUENCY a. Enter 3-digit CHANNEL NUMBER b. NO for RECEIVE ONLY

9. Select COMSEC a. Select CRYPTO MODE (VINSON for 25 kHz or ANDVT for 5 kHz channel) b. Select CRYPTO KEY c. Training Frames must match on all terminals.

10. Select TRAFFIC. For VINSON set to VOICE; for ANDVT set to VOICE & DATA 11. Select TX POWER to change power (HIGH is default) 12. Skip SQUELCH (it cannot be edited) 13. Select EXIT 14. Press PGM to exit to operational screen

17


AN/PRC-150

18


CONFIGURATION PROGRAMMING

1. Press PGM 2. Select CONFIG then RADIO 3. Set the following items: TX POWER, SQUELCH, SQUELCH LEVEL, FM SQUELCH

TYPE, RADIO SILENCE, COUPLER, FM DEVIATION, CW OFFSET, RX NOISE BLANKING, COMPRESSION, EXT, 20W PA/COUPLER, & ERROR BEEPS

4. Press PGM to exit.

PROGRAMMING CHANNEL PRESETS

1. Press PGM 2. Select MODE, PRESET, CHANNEL 3. Enter Channel # (000 – 199) 4. Enter RX FREQUENCY 5. Enter TX FREQUENCY 6. Select MODULATION (USB, LSB, FM, AME, CW) 7. The rest can normally be left at default: AGC SPEED, IF BANDWIDTH, RX ONLY,

LIMIT MAX TRANSMIT POWER, ENABLE HAIL TX, & ENABLE SSB SCAN. 8. Enter next channel #, repeat steps 4-7. 9. Press CLR then PGM to exit

LOADING COMSEC INTO THE RADIO with ANCD

1. Place Function Switch to LD 2. Select FILL DEVICE (KYK-13, KYX-15, etc) 3. Select CRYPTO TYPE (ANDVT, VINSON, KG-84) 4. Select KEY TYPE (TEK, KEK) 5. Select KEY NUMBER (01-25) 6. Turn on ANCD 7. Select APPL, press ENT 8. Select RADIO, press ENT 9. Select COMSEC, press ENT 10. Select LD, press ENT 11. Select TEK, press ENT 12. SELECT KEY is highlighted. P DN until the correct key is displayed. Press ENT, XMT appears in the bottom right corner 13. Select QUIT, press ENT 14. Connect ANCD to radio, press ENT on ANCD. 15. ANCD displays Sending TEK xxxx followed by Press [LOAD] on RT 16. Press ENT to initiate Fill. 17. Answer LOAD ANOTHER KEY – YES or NO as desired. 18. When finished:

a. Turn off fill device and disconnect from radio. b. Rotate FUNCTION SWITCH to CT or TD position.

19


LOADING COMSEC INTO THE RADIO with SKL

1. Place Function Switch to LD 2. Select FILL DEVICE (KYK-13, KYX-15, etc) 3. Select CRYPTO TYPE (ANDVT, VINSON, KG-84) 4. Select KEY TYPE (TEK, KEK) 5. Select KEY NUMBER (01-25) 4. On the SKL, select the Keys tab. 5. Select a key then the Load icon in the upper right. 6. Use DS-102 protocol KYK13 activation mode, click OK. 7. At Ready to Send Key screen, click OK. 8. The Status screen will display Press INITIATE Button 9. Press ENT on the radio to initiate Fill. 10. Answer LOAD ANOTHER KEY – YES or NO as desired. 11. When finished:

a. Turn off fill device and disconnect from radio. b. Rotate FUNCTION SWITCH to CT or TD position.

ASSIGNING COMSEC TO MANUAL PRESET

1. Place Function Switch to CT 2. At operational screen, press Left Arrow key twice. ----- is highlighted. 2. Press Up or Down Arrow key until correct key is shown (ANDVT-HF). Press ENT 3. CHANGE COMSEC MODE? Select YES

PROGRAMMING PRESETS (MANUAL)

1. Press PGM 2. Select MODE, PRESET, MANUAL 3. Select RADIO MODE (FIX) 4. Select CHANNEL NUMBER 5. Select MODEM PRESET (OFF for voice) 6. Select ENCRYPTION TYPE (TYPE I) 7. Select CRYPTO MODE (ANDVT-HF, VINSON) 8. Select ENCRYPTION KEY 9. Select PT VOICE MODE 10. Select CC/CT VOICE MODE 11. Select ENABLE (yes) 12. Press PGM to exit

20


PROGRAMMING PRESETS (SYSTEM)

1. Press PGM 2. Select MODE, PRESET, SYSTEM 3. Select SYSTEM PRESET TO CHANGE (SYSPRE1 – SYSPRE75) 4. Name the PRESET. 5. Select RADIO MODE (FIX, ALE, etc) 6. Select CHANNEL NUMBER 7. Select MODEM PRESET (OFF for voice) 8. Select CRYPTO MODE (TYPE I) 9. Select CRYPTO MODE (ANDVT-HF, VINSON) 10. Select ENCRYPTION KEY 11. Select PT VOICE MODE 12. Select CC/CT VOICE MODE 13. Select ENABLE (yes) 14. Press PGM to exit

21


PROGRAMMING ALE

1. Program all Channels first! 2. Press PGM 3. Select MODE, ALE, then CHAN_GROUP 4. Select ADD; enter CHANNEL GROUP number 5. Select ADD; enter CHANNEL numbers (all channels for the ALE net) 6. Press CLR 3 times. 7. Select ADDRESS 8. Select SELF for ADDRESS TYPE 9. Select ADD; enter 3-digit Self Address 10. Select the CHANNEL GROUP (from step 4) 11. Select INDIVIDUAL for ADDRESS TYPE 12. Select ADD; enter 3-digit INDIV ADDR (other stations in ALE net) 13. Select CHANNEL GROUP (from step 4) 14. Select Self Address for ASSOC SELF (from step 9) 15. Repeat 11 – 14 for each station in ALE Net 16. Select NET for ADDRESS TYPE 17. Select ADD; enter Net Address 18. Select the CHANNEL GROUP (from step 4) 19. Select Self Address for ASSOC SELF (from step 9) 20. Select ADD (NET MEMBER); press ENT until MEMBER LIST FULL is displayed. 21. Press CLR 5 times 22. Select CONFIG 23. Enter the number of channels in the ALE net for MAX SCAN CHANNELS (# in the Channel Group) 24. Select ON for LISTEN BEFORE TX 25. Select OFF for KEY TO CALL 26. Select MAX TUNE TIME 27. Select LINK TIMEOUT (ON/OFF) 28. Select LINK TO ANY CALLS (ON/OFF) 29. Select LINK TO ALL CALLS (ON/OFF) 30. Select LINK TO INLINK CALLS (ON/OFF) 31. Select ENABLED for AMD OPERATION 32. Select ENABLED for AMD AUTO DISPLAY 33. Select ASYNC for SCAN RATE 34. Select LINK PROTECT LEVEL (ON/OFF) 35. Enter LINK PROTECT KEY 36. Press PGM to exit 37. Enter ALE Mode.

22


AN/PRC-117

23


LOS FIX FREQUENCY PROGRAMMING 1. Press PGM

a. Select NORM, NET b. Select desired Net number to modify (00-99) c. Select ACTIVATE IN LIST? - YES. d. Select NET TYPE. Select LOS Fix Frequency

2. Select FREQ a. Enter the receive then transmit frequencies. b. RECEIVE ONLY? Select NO

3. Arrow to COMSEC a. Select desired COMSEC mode (VINSON, ANDVT, FASCINATOR or KG-84) b. Select desired key variable (e.g. TEK 01) c. Select ANALOG DATA, YES or NO (NO for voice only)

4. Arrow to DATA/VOC field. a. Select AUTO ON ADF (J1) PORT for voice or AUTO ON DATA (J3) PORT b. Select 8.0, 5.0, or 6.5 kHz Deviation for FM as required (6.5 kHz SINCGARS) c. Select SYNC or ASYNC as required d. Select desired modulation, FM is default (FM, AM, TCM, or HPW)

5. Arrow to SQUELCH field a. Select desired Squelch mode (None, Analog Tone or Noise, or Digital) (30-90 MHz use

Tone, 90-512 MHz use Noise) 6. Arrow to POWER field, select desired power output 7. Arrow to NAME field

a. Enter a name for this Net. Name can be up to 12 characters long 8. Press CLR key 3 times or press PRE +/- to go to operational display

24


TACSAT PROGRAMMING (DEDICATED) 1. Press PGM

a. Select NORM, NET b. Select desired Net number to change (00 – 99) c. Select ACTIVATE IN LIST? - YES d. Select NET TYPE - SATCOM

2. Arrow to FREQ a. Enter the FREQUENCY CODE, (001-239) or... b. Enter 999 for manual entry of the receive and transmit frequencies c. RECEIVE ONLY? Select NO

3. Arrow to COMSEC a. Select the appropriate COMSEC mode (VINSON for 25 kHz, ANDVT for 5 kHz or

KG-84) b. Select correct key variable (e.g. TEK 01) c. Select correct Training Frames (ANDVT) or correct Redundancy (KG-84) d. Select ANALOG DATA, YES or NO (NO for voice only)

4. Arrow to DATA/VOC. If you used a Freq code in step 2, normally you can skip step 4. a. Select MODULATION – MS181 for 25kHz & 5kHz dedicated channels or Select HPW

for High Performance Waveform data transfer. b. Select SYNC or ASYNC as required

5. Arrow to SQUELCH - select Digital Squelch ON or OFF as required 6. Arrow to POWER - select desired power output 7. Arrow to NAME field

a. Enter a name for this Net. Names can be up to 12 characters long. 8. Press CLR key 3 times or press PRE +/- to go to operational display

25


LOADING COMSEC INTO THE RADIO with ANCD

1. Place Function Switch to LD 2. Select FILL DEVICE (KYK-13, KYX-15, etc) 3. Select CRYPTO TYPE (ANDVT, VINSON, KG-84) 4. Select KEY TYPE (TEK, KEK) 5. Select KEY NUMBER (01-25) 6. Connect the Fill Device to J1 and turn it on. 7. Select APPL, press ENT 8. Select RADIO, press ENT 9. Select COMSEC, press ENT 10. Select LD, press ENT 11. Select TEK, press ENT 12. SELECT KEY is highlighted. P DN until the correct key is displayed. Press ENT, XMT appears in the bottom right corner 13. Select QUIT, press ENT 14. Connect ANCD to radio, press ENT on ANCD. 15. ANCD displays Sending TEK xxxx followed by Press [LOAD] on RT 16. Press ENT to initiate Fill 17. Answer LOAD ANOTHER KEY – YES or NO as desired. 18. When finished:

a. Turn off fill device and REMOVE b. Rotate FUNCTION SWITCH to CT or TD position.

LOADING COMSEC INTO THE RADIO with SKL

1. Place Function Switch to LD 2. Select FILL DEVICE (KYK-13, KYX-15, etc) 3. Select CRYPTO TYPE (ANDVT, VINSON, KG-84) 4. Select KEY TYPE (TEK, KEK) 5. Select KEY NUMBER (01-25) 6. Connect the Fill Device to J1 and turn it on. 7. On the SKL, select the Keys tab. 8. Select a key then the Load icon in the upper right. 9. Use DS-102 protocol; KYK13 activation mode, click OK. 10. At Ready to Send Key screen, click OK. 11. The Status screen will display Press INITIATE Button 12. Press ENT on the radio to initiate Fill 13. Answer LOAD ANOTHER KEY – YES or NO as desired. 14. When finished:

a. Turn off fill device and REMOVE b. Rotate FUNCTION SWITCH to CT.

26



1. Rotate function switch to LD position. 2. Select FILL DEVICE as CYZ-10 RDS. Press ENT. 3. Connect FILL Device to the ADF Port (J1) of the radio. 4. On CYZ-10, load Radio application. 5. On CYZ-10, select Send. Press ENTR. 6. On CYZ-10, select Send to: Radio. Press ENTR. 7. On CYZ-10, select iCom. Press ENTR. 8. On CYZ-10, follow on-screen steps until asked whether to include time. 9. On radio, press ENT to initiate the fill. Radio will display FILL IN PROGRESS. 10. On CYZ-10, select Include Time – Y/N as required. Press ENTR. 11. The Mode 2/3 fill process will now begin and will take approximately 1 minute. 12. Select MORE FILL DATA? – NO when complete or YES to load additional crypto 13. Turn off and disconnect Fill Device from the radio. 14. Change the function switch back to the PT, CT, or TD position.

LOADING SINCGARS FH LOADSET WITH AN SKL 1. Rotate function switch to LD position. 2. Select FILL DEVICE as CYZ-10 RDS. Press ENT. 3. Connect FILL Device to the ADF Port (J1) of the radio. 4. On SKL, select Eqs Tab. 5. On SKL, select RT-1523. 6. On SKL, select the LOAD icon in the upper right. 7. On SKL, select ICOM Transfer. Do Not check Include Time; it will fail! Click OK. 8. On SKL, at the Connect To screen, select Next>> 9. On radio, press LOAD button. 10. On SKL, at the Profiles screen, select Send. SKL displays Press LOAD Button. Observe progress on SKL. Transfer takes about 20 seconds. 11. Select MORE FILL DATA? – NO when complete or YES to load additional crypto 12. Turn off and disconnect Fill Device from the radio. Move SW from LD position to CT.

27


SINCGARS FREQUENCY HOPPING (ECCM) PROGRAMMING 1. Press PGM, NORM, NET 2. Select the Net number to modify (00-99) 3. Select ACTIVATE IN LIST? – YES 4. Select NET TYPE - FREQUENCY HOPPING 5. HOPPING TYPE – select SINCGARS 6. Arrow to HOPSET

a. Select the desired HOPSET COMPARTMENT (Hopset ID number) b. Select LATE NET ENTRY - ON or OFF, as required. For normal operations, select NO

7. Arrow to COMSEC a. Select the appropriate COMSEC mode (VINSON, KYV-5) b. Select desired key variable (e.g. TEK 01) c. Select ANALOG DATA, YES or NO (default NO)

8. Arrow to DATA/VOC. a. Select AUTO ON ADF (J1) PORT for voice or AUTO ON DATA (J3) PORT b. Select SYNC or ASYNC as required

9. Arrow to POWER. Set as required 10. Arrow to NAME. Enter desired Net name 11. Press CLR once to go to the NET GENERAL display

a. Arrow to GENERAL b. HOPPING TYPE – select SINCGARS c. Select CONFIG d. Select ACTIVATE CUE FREQUENCY? NO or YES as required. If YES, enter Cue

Frequency e. Select SINCGARS MEMBER or MASTER, as required

12. Use HOPSET_COPY to copy a HOPSET to change Net IDs. Up to 25 net IDs. 13. Press CLR key 3 times or press PRE +/- to go to operational display

28


DAMA NET PROGRAMMING 1. Press PGM

a. Select DAMA, PRESETS, NETS d. Select the desired Net (0-9) e. ACTIVATE IN LIST, select YES

2. Arrow to CHANNEL a. Enter the CHANNEL NUMBER b. Enter the TRANSMIT CAPABILITY (FULL, EMCON) c. Enter the CONSTANT KEY PORT (YES, NO) d. Enter the default Port Configuration (Name)

3. Arrow to RANGING a. Enter the Ranging Method (ACTIVE, PASSIVE, FIXED)

4. Arrow to ADDR a. Select BASE_ADDRESS, enter the Base Address (TBA) b. Select GUARD_LIST, enter the Network Address

5. Arrow to TRANSEC a. Select ORDERWIRE ENCRYPTION, ON b. Select the TSK position for key locations 0-3, (4-7 are none).

6. Arrow to POWER a. Select desired power output

7. Arrow to NAME and enter a unique net name.

DAMA PORT CONFIGURATION PROGRAMMING 1. Press PGM

a. Select DAMA, PRESETS, PORT_CONFIGS d. Select the desired Port Configuration (0-9)

2. Arrow to COMSEC a. Select COMSEC Mode (VINSON, ANDVT, KG-84, NONE) b. Select the desired encryption key (TEK01). c. Select ANALOG DATA (YES, NO) for VINSON d. Select TRAINING FRAMES (6, 9, 12, 15, 20, 30, and 60) in ANDVT e. Select SYNCHRONIZATION (MODES 1-4) in KG-84

3. Arrow to DATA/VOC a. If VINSON was selected,

1. Select AUTO ON ADF PORT or AUTO ON DATA PORT b. If ANDVT was selected, (ANDVT is the normal COMSEC for DAMA)

1. Select SYNC or ASYNC 2. Select BAUD RATE (300, 600, 1200, or 2400 for voice)

c. If KG-84 was selected, 1. Select SYNC or ASYNC 2. Select BAUD RATE (75, 300, 600, 1200, 2400, 4800, 16K)

4. Arrow to CONFIG_CODE a. Select the 25 KHz PORT CFG CODE (60) b. Select the 5 KHz PORT CFG CODE (60)

29


30

DAMA DESTINATION PROGRAMMING 1. Press PGM

a. Select DAMA, PRESETS, DESTINATIONS d. Select the desired Destination location to program (0-49)

2. Program the following parameters as required a. 5 KHz Destination or b. 25K_AC Destination enter the Network Address from the Guard List. c. 25K_DC Destination d. SEARCH (GLOBAL, LOCAL) e. Name the Destination Preset

Date post:	29-Jul-2020
Category:	Documents
Upload:	others
View:	13 times
Download:	2 times

EAGLE - Noodlez.org Courses PDF Student Guides... · loading comsec variable with ancd 4 loading...

Documents