1 Español p. 18 EASY BREEZE CEILING FAN ITEM #0698390, 0698391 MODEL #00887, 00888 Serial Number Purchase Date Harbor Breeze ® is a registered trademark of LF, LLC. All Rights Reserved. Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-473-4537, 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday. EB165 ATTACH YOUR RECEIPT HERE UL MODEL #EBZ54 Lowes.com/harborbreeze Lowes.com/harborbreeze
Transcript
1
Español p. 18
EASY BREEZE CEILING FANITEM #0698390, 0698391
MODEL #00887, 00888
Serial Number Purchase Date
Harbor Breeze ® is a registered trademark of LF, LLC. All Rights Reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-473-4537, 8 a.m. - 7 p.m., EST, Monday - Friday,9 a.m. - 6 p.m., EST, Saturday.
Replacement Parts List ...................................................................................................... 17
SAFETY INFORMATION
WARNING
CAUTIONREAD AND SAVE THESE INSTRUCTIONSPlease read and understand this entire manual before attempting to assemble, operate or install the product.
• When using an existing outlet box, be sure the box is securely attached to the building structure and can support the full weight of the fan, so to avoid potential serious injury or death.• All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electricalcodes.Electricalinstallationshouldbeperformedbyaqualifiedlicensedelectrician.• DONOTusebulbswithwattagegreaterthanthemaximumvaluestatedonthefixtureandin thismanual.Usingahigherwattagebulbthanspecifiedwillincreasefixturetemperatureand causeriskoffire.• Disconnect the electrical supply circuit to the fan before installing kit.• Electrical diagrams are for reference only.• The net weight of this fan including the light kit is: 22 lbs.
• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, do not use this fan with any solid-state speed control device.• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, make sure the electricity has been turned off at the circuit breaker or fuse box before beginning installation. • PERSONAL INJURY HAZARD - To reduce the risk of injury to persons, install fan so that the bladesare7ft.abovethefloor.• ELECTRIC SHOCK HAZARD - Do not install this fan with variable speed wall control or wall- mounted dimmer switch. It will permanently damage the fan’s remote control receiver and cause the fan’s functions to fail.
ON
ON / OFF switch NO Variable speed wall control NO Dimmer switch
• FIRE,ELECTRICSHOCKORPERSONALINJURYHAZARD-Toreducetheriskoffire,electric shock, or personal injury, mount to an outlet box marked “ACCEPTABLE FOR FAN SUPPORT OF 35.1 lbs OR LESS” and use the mounting screws provided with the outlet box. Mostoutletboxescommonlyusedforthesupportoflightingfixturesarenotacceptableforfansupportandmayneedtobereplaced.Consultaqualifiedlicensedelectricianifindoubt.
• PERSONAL INJURY HAZARD - To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the fan. DO NOT insert foreign objects in between the rotating fan blades.
Lowes.com/harborbreeze Lowes.com/harborbreeze
A 1B 1C 1D 1E 1F 1G 5H 5I 1J 1K 1L 1M 1
54
HARDWARE CONTENTS (shown actual size)
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
A Mounting Bracket (preassembled to canopy (B))CanopyCanopy Cover (preassembled to canopy (B))Yoke CoverDownrod AssemblyMotor AssemblyBlade BracketBladeSwitch BoxLight KitGlassGlass Cap (preassembled to light kit (J))Finial (preassembled to light kit (J))
PART DESCRIPTION QUANTITY
A
B
C
D
E
F
G
K
L
M
J
H
I Blade BracketScrew
Qty. 10 + 1 extra
WireConnector
Qty. 3 + 1 extra
AA BB
EE FF
Blade ScrewQty. 15 + 1 extra
Rubber Gasket Qty. 1
(NOT TO SCALE)
(NOT TO SCALE) (NOT TO SCALE)
CC DD
Fan Pull Chain Extension Qty. 1
Light Pull Chain Extension Qty. 1
Lowes.com/harborbreeze Lowes.com/harborbreeze
6 7
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
1. Determine mounting method to use. A - Downrod Mount (normal or angled ceiling) B - Closemount (normal ceiling only)
Important: lf using the angle mount, check to make sure the ceiling angle is not steeper than 20°.
4. Install the mounting bracket (A) to the outlet box (not included) using the two screws provided with the outlet box. Securely tighten the two screws.
2.Removeanddiscardthefiverubberinsertsandfivemountingscrewsfromtheundersideof the motor assembly (F).
2. Insert downrod assembly (E) through canopy (B), canopy cover (C) and yoke cover (D). Thread wires from the motor assembly (F) up through downrod assembly (E).
Outlet box
A
4
3. Remove the mounting bracket (A) from the canopy (B) by loosening the four preassembled screws on the top of the canopy (B). Remove the two non-slotted screws and save.
1
A
B
Loosen butdo not removeA
Removeand save
A
B
3
If using the angle mount, make sure open end of mounting bracket (A) is installed facing the ceiling.
Follow mounting instructions for Downrod Style Fan Mounting on page 7 or Closemount Style Fan Mounting on page 8, depending on mounting method (A or B) chosen in step 1 on page 6.
DOWNROD STYLE FAN MOUNTING
1. Remove pin and clip from downrod assembly (E) and save.
Rubber insert and screw
F2
E
B
C
D
E
Clip
Pin
E
1
2
Lowes.com/harborbreeze Lowes.com/harborbreeze
8 9
DOWNROD STYLE FAN MOUNTING CLOSEMOUNT STYLE FAN MOUNTING
3. Loosen the two set screws from the yoke. Slip downrod assembly (E) into yoke, aligning holes in downrod assembly (E) and yoke. Insert the pin through yoke and downrod assembly (E), then insert clip into pin until it snaps into place. Tighten set screws. Slide the yoke cover (D) down over the motor assembly (F).
2. Remove every other screw from the top of the motor assembly (E) -- for a total of 3 screws -- and save.
4. Install hanger ball on the top of downrod assembly (E) into mounting bracket (A) opening. Rotate fan until slot on hanger ball engages the tab on the mounting bracket (A).
3. Place the rubber gasket (FF) over the remaining screws on motor assembly (F). Pull wires from motor assembly (F) through hole in canopy (B), and attach canopy (B) using the three screws previously removed. Tighten the screws securely.
1. Remove the canopy cover (C) from the bottom of the canopy (B).
4. Temporarily hang the canopy (B) onto the hook on the mounting bracket (A) using one of the non-slotted holes in the canopy (B). This will allow for hands-free wiring.
H
F
2
1
DANGER: Be careful when aligning the tab to the slot! If not fully engaged, there is a possibility of fan falling, which may result in serious injury or death.
Proceed to WIRING on page 10.
CLOSEMOUNT STYLE FAN MOUNTING
H
Hardware Used
FF Rubber Gasket x 1
H B
FF
4
TabSlot
A
E
3
H B
FF
3
4
ClipPin
Set screw
E D
F
Yoke
C
B
BF
FF
A
B
Hook
Lowes.com/harborbreeze Lowes.com/harborbreeze
10
WIRING
Hardware Used
1. Connect the GREEN/GROUND wire from fan to the BARE/GREEN supply wire. Connect the BLACK/BLUE wire from the fan to the supply BLACK wire. Connect the WHITE wire from fan to the supply WHITE wire.
2. To connect wires, twist wire ends together and screw wire with wire connectors (AA) in a clockwise direction. Tape the wire connectors (AA) and wires together with electrical tape (not included). Be sure no bare wire or wire strands are visible after making connection.
Place GREEN and WHITE connections on opposite side of box from the BLACK and BLUE connections. The splices should be turned upward and pushed carefully up into the outlet box.
1
2
x 3 Wire ConnectorAA
FINAL INSTALLATION
You may now proceed to Step 4.
3. Directly align the locking slots of the canopy (B) with the two screws previously loosened (step 3, page 6) in the mounting bracket (A). Push up to engage the slots and turn clockwise to lock in place. Immediately tightenthetwoscrewsfirmly,thenre-installthetwoscrews that were previously removed (step 3, page 6) to fully secure the canopy (B) to the mounting bracket (A).
4. Attach blade (H) to a blade bracket (G) using three blade screws (BB).
Repeat for remaining blade assemblies.
11
2. Re-install the two screws that were previously removed (step 3, page 6) to fully secure the canopy (B) to the mounting bracket (A).
AA
FINAL INSTALLATION
If you installed the fan with “Closemount Style FanMounting”, continue to Steps 1 and 2. If you installedthe fan with “Downrod Style Fan Mounting”, skip to Step 3.1. Remove the fan from the hook on the mounting
bracket (A). Align the locking slots of the canopy (B) with the two screws previously loosened (step 3, page 6) in the mounting bracket (A). Push up to engage the slots and turn clockwise to lock in place. Immediatelytightenthetwoscrewsfirmly.
BB Blade Screw x 15
Hardware Used
H
G
BB41
2
3
Grounded/Green
Black
White
Grounded/Green
BlackBlue
White
Supply circuit
Speed switch
Outlet box
Blu
eB
lack
Whi
teG
reen
Whi
te
GREEN/GROUNDED
Blac
k
Lockingslots
Outletbox
Screws
HookB
A
Outlet boxScrew
B
Outlet boxScrew
B
NOTE: BLACK wire is hot power for fan. BLUE wire is hot power for light kit. WHITE wire is common for fan and light kit. GREEN wire is ground wire. WARNING: If house wires are different colors than referred to above, stop immediately. Consult a licensed electrician to determine proper wiring.
Lowes.com/harborbreeze Lowes.com/harborbreeze
12 13
FINAL INSTALLATION
5. Align the post of blade bracket (G) to the slot on the bottom of the motor housing assembly (F). Secure each blade bracket (G) using 2 blade bracket screws (EE).
Repeat this step for the remaining blade assemblies.
8. Remove and save three preassembled screws from light kit (J). Connect the BLUE wire from motor assembly (F) to BLACK wire from light kit (J). Connect WHITE wire from motor assembly (F) to WHITE wire from light kit (J).
Attach the light kit (J) to the switch box (I) on bottom of motor assembly (F). Replace the previously removed screws and securely tighten all screws.
9. Removethepreassembledfinial(M),glasscap(L),rubber washer and hex nut from light kit (J).
10. Place glass (K) on the preassembled pipe on the lightkit(J)untilitisflushwiththepreassembledmetal disk. Thread fan pull chain through side hole on glass (K). Make sure pull chain hangs clear and is not tangled in light kit (J). Thread light kit pull chain through center hole on glass (K).
Place previously removed rubber washer and hex nut onto the pipe and securely tighten.
FINAL INSTALLATION
7. Connect the MALE plug from motor assembly (F) to the FEMALE plug from switch box (I). Attach the switch box (I) to the bottom of the motor assembly (F) by aligning the keyholes on the switch box (I) with the loosened screws on the support plate of motor assembly (F). Twist switch box (I) until the loosened screws engage the narrow end of the keyholes, then replace previously removed screw and securely tighten all screws.
6. Loosen two of the three preassembled screws from the support plate of motor assembly (F). Remove and save remaining preassembled screw.
EE Blade Bracket Screw x 10
Hardware Used
H B
FF
5
H B
FF
6
7
8
9
10
EE F
Screw
F
BlackBlue
White
J
I
Rubber washerHex nut
ML
J
Rubber washerHex nut
K
KeyholeMale plugFemale plug
Screw
I
F
Lowes.com/harborbreeze Lowes.com/harborbreeze
14 15
Hardware Used
11. Pass fan pull chain through side hole on glass cap (L), thenplaceglasscap(L)andfinial(M)overpipeandsecurely tighten.
12. Attach fan pull chain extension (CC) and light kit pull chain extension (DD) to corresponding chains.
Assembly is now complete.
FINAL INSTALLATION
Light pull chain extensions
x CC
DD
1
x 1
Fan pull chain extensionsH B
FF
11
H B
FF
12
L
M
CC
DD
1. PULL CHAIN:
2. REVERSE SWITCH:When the season changes, you may want to change the direction your fan spins. To switch between clockwiseandcounterclockwiserotations,flipthefanreversal switch.WARNING: Wait for fan to stop before reversing the switch.A. In cooler weather, clockwise rotation creates an
upwardairflow,whichmoveshotairfromtheceiling into the room. Push the switch RIGHT.
B. In warmer weather, counterclockwise rotation createsadownwardairflow,whichcoolstheair.Push the switch LEFT.
• The fan pull chain is for motor speed control: High, Medium, Low and Off. Pull chain once for each position.
• ThelightpullchaincontrolsthelightfixtureeitherON or OFF with each pull of the chain.
OPERATING INSTRUCTIONS
Fan pull chain
Light pull chain
Lowes.com/harborbreeze Lowes.com/harborbreeze
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONFan does not move. 1. Chain switch is “off”.
2. Faulty wire connection.3. Reverse switch not engaged.
1. Pull chain switch.2. Turn power off. Loosen canopy,
check all connections.3. Pushswitchfirmlyeitherway.
1. Tighten all blade screws.2. Replace blades (call customer
service).3. Replace with an approved speed
control device.Excessive wobbling. 1. The blades are loose.
2. Blade brackets incorrectly attached.
3. Unbalanced blades.4. The fan is not securely mounted.5. Fan too close to vaulted ceiling.
1. Tighten all blade screws.2. Reinstall blade brackets.3. Switch with blade from the
opposite side.4. Turn power off. Carefully loosen
the canopy and remount securely.5. Lower fan or move it to another
location.
TROUBLESHOOTING
CARE AND MAINTENANCE
IMPORTANT: Shut off main power supply before beginning any maintenance.
• Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
• Cleanfanhousingwithonlyasoftbrushorlint-freeclothtoavoidscratchingthefinish.Cleanblades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to blades for added protection.
• At least twice a year, tighten all screws and lower canopy to check mounting bracket screws and downrod assembly.
The manufacturer warrants this fan to be free from defects in workmanship and material present at time of shipment from the factory for lifetime limited from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at no charge or at our option replace the ceiling fan with a comparable or superior model.
To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the ceilingfanbyaccident,misuse,orimproperinstallation,orbyaffixingaccessoriesnotproducedbythe manufacturer of the fan, are at the purchaser’s own responsibility. The manufacturer assumes no responsibility whatsoever for fan installation during the lifetime limited warranty. Any service performed by an unauthorized person will render the warranty invalid.
Duetovaryingclimaticconditions,thiswarrantydoesnotcoverchangesinbrassfinish,rusting,pitting,tarnishing,corroding,orpeeling.Brassfinishfansmaintaintheirbeautywhenprotectedfromvarying weather conditions. Any glass provided with this fan is not covered by this warranty. Any replacementofdefectivepartsfortheceilingfanmustbereportedwithinthefirstyearfromthedateof purchase. For the balance of the warranty, call our customer service department at 1-866-473-4537 for return authorization and shipping instructions so that we may repair or replace the ceiling fan. Any fan or parts returned improperly packaged is the sole responsibility of the purchaser. There is no further expressed warranty. The manufacturer disclaims any and all implied warranties.
The duration of any implied warranty which can not be disclaimed is limited to the lifetime limited periodasspecifiedinourwarranty.Themanufacturershallnotbeliableforincidental,consequentialor special damages arising at or in connection with product use or performance except as may otherwisebeaccordedbylaw.Thiswarrantygivesyouspecificlegalrightsanyoualsohaveotherrights which may vary from state to state. This warranty supersedes all prior warranties.
Note: A small amount of “wobble” is normal and should not be considered a defect.
Printed in China
For replacement parts, call our customer service department at 1-866-473-4537,8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday.
GA
H
EHarbor Breeze ® is a registered trademark of LF, LLC. All Rights Reserved.
