IMG

0442

RP

imag

ri.c

om.a

u 0

2/08

Easy Installation in 4 simple steps

Installation Instructions for Storm Drain System

1. Dig the trench

• Form trench for Reln Storm Drain System allowing for a 50mm bed of packed sand and wide enough for a minimum of 100mm backill of concrete on each side.

• Allow slope of approximately 30cm to every 20m.

2. Insert End Cap or End Outlet

• Join Reln Storm Drain System. Joins and End Caps may be sealed with silicone. Use Reln End Cap at highest point of Reln Storm Drain Channel. Connect the low end of the Storm Drain Channel to a Rainwater Pit, or, using 90mm PVC pipe use built in Bottom Outlet, or it an End Outlet to allow water to clear.

• Lay Storm Drain Channel out with 90˚ Corner Piece or Tee Piece connected and End Cap itted prior to concreting.

3. Snap together lengths

• Storm Drain Channel can be cut to length with a hacksaw, install with grate itted.

• Protect grate with masking tape during concrete pour.

4. Finish.

• Top of grate must be 2mm below concrete or paver surface.

• Allow 72 hours for concrete to cure before vehicle use or removal of grates.

www.reln.com.au

Reln Pty Ltd. 14B Williamson Road Ingleburn NSW 2565

Phone 1300 137 356 Fax 1300 137 358 Email sales@reln.com.au

New Zealand-Dux Industries Ltd. Phone 0800 367 389.

www.reln.com.au

Easy to install!

Storm Drain Technical Details. Length Width Height Weight

Storm Drain with Plastic Grate 1010mm 120mm 129mm 2.3kg

Storm Drain with Stainless Steel Grate 1010mm 120mm 129mm 3.2kg

Storm Drain End Outlet 35mm 120mm 123mm 50gms

Storm Drain 90° Corner 170mm 170mm 127mm 400gms

Designed to withstand 5 tonne vehicle weight without

moving in concrete

Drainage System Components

Slim-line Pit Joiner and 3m Channel& End Outlet 90˚ Corner End Cap Tee Piece 1m Channel Bottom Outlet Channel Options Grate OptionsLeaf Guard

Bottom outlet on the Slim-line Pit or Channel can be cut or drilled to allow more flexibility with paving.

Sizes available: 1 metre and 3 metre lengths. Also available as a Garage Pack which includes 4 x 1 metre lengths with black grates plus a BONUS End Cap and End Outlet.

Garage Pack Product Code: 003141

• Coloured grates available in: black, stainless steel, sandstone, terracotta, portland grey, heritage green

• Heavy Duty Grates (Class C Ductile Iron)

• Available in 1m lengths only

• Designed for fast easy connection to Reln Storm Drain.

• When installed the Slim-line Pit looks like part of the Channel.

Product Code: 003430

• Tough, durable & lightweight• Available in 1m or 3m lengths for greater lexibility• Joiner included for 3m ChannelProduct Code: 003301

• Fits 90mm PVC pipe• Easy to install to end of

Channel• PredrilledProduct Code: 003408

• Corner peice connects Channels to make 90 degree corners and T-intersections

• Tough, durable, lightweightProduct Code: 003401

• End Cap slips into Storm Drain at either end of Channel

• Used to seal high end of drain

Product Code: 003407

• The quick and easy way to create a branch line with Channel

Product Code: 003121

• Tough, durable & lightweight

• Available in 1m or 3m lengths for greater flexibility

Product Code: 003101

• Prevents passage of leaves and debris entering stormwater systems and waterways

Product Code: 003410

1 2 3 4 5 6 7 8 9

Pre drilled End Outlet is quicker

to install PVC stormwater pipe.

Bottom outlet can be cut or drilled to allow more flexibility with paving.

Easy clip out grate for cleaning

90° Corner allows left or right hand extension of the

Reln Storm Drain.

Joiner2

3m Channel3

LeafGuard

4

90° Corner6

End Cap7Tee Piece8

1m Channel9

Preformed pipe outlets allow for quick and easy glueing

of ø90mm PVC stormwater pipe

Leaf Guard prevents

leaves from blocking

outlets and pipes.

Slim-line Pit 1

Easy joining

ø90mm PVC Stormwater Pipe

End Outlet5

Designed to withstand 5 tonne vehicle weight without moving in concrete