14
!"#$%%%%&'
!"#$%%%%&'
11/3/08
!"#$%%%%&(
!"#$%%%%&)
11/3/08
!"#$%%%%&*
!"#$%%%%+%
!"#$%%%%+,
!"#$%%%%+-
11/3/08
!"#$%%%%+&
SITE PLANNING DATA
SYSTEM 9395-825 ISBM, MODELS 650, 750, 825kVA, SINGLE M
ODULE
MAINTENANCE BYPASS SWITCHGEAR (OPTION)
AC OUTPUT
MIS
MBP
TO LOAD
UPS M
ODULE
ISBM
BYPASS
AC INPUT
MBB
RECTIFIER
CB1 (OPTION)
BATTERY
AC INPUT
UPM1
UPM2
UPM3
UPM1
UPM2
UPM3
Notes:
ISBM
1. Rectiÿer AC input current calculations: Continuous - 100% load without charging; Nameplate -
9. The UPS cabinet can be installed in line-up-and-m
atch or standalone conÿgurations.
100% load with m
axim
um charging.
10. Top and bottom cable entries through removable access plates are standard for all conÿgurations.
2. Inverter AC output current calculation: Nameplate - 100% rated output load.
Access plates shall be custom-m
odiÿed to suit conduit sizes.
3. Bypass AC input current calculation is based on 100% rated output.
11. All wiring is to be in accordance with National and Local Electric Codes.
4. The system m
ust be installed on a level "oor suitable for computer or electronic equipment.
12. AC input to UPS rectiÿer (0.98 m
in.pF): (3) phases, (1) ground.
5. The system m
ust be installed in a temperature and humidity controlled indoor area
AC output to load: (3) phases, (1) neutral if required, (1) ground.
free of conductive contaminants.
AC input to UPS bypass: (3) phases, (1) neutral if required, (1) ground.
6. Ambient temperature range: 0-40C (32-104F); Recommended operating range: 20-25C (68-77F);
DC input from battery to UPS: (1) positive, (1) negative, (1) ground.
Maxim
um relative humidity: 95% non-condensing.
13. The front panels m
ust be removed to m
eet the 830mm (or 32.7" depth) to ÿt through doors.
7. Minim
um overhead clearance for ventilation above the UPS cabinet is 457mm (18in.).
14. If the UPS is to be installed with the right side near a wall a m
inim
um of 6" is required betw
een the
8. Minim
um 915mm (36in.) clearance in front of the UPS cabinet is required for cooling air intake
wall and the unit. If a battery cabinet is installed to the right of the UPS the 6" are not required.
and servicing space.
15. Speciÿcations are subject to change.
Product Speciÿcations
Battery
Inverter AC
Nameplate
AC
Max. Battery Current
AC
Rectiÿer AC Input Current
Max. Heat
Approx. Weight
Output Current
UPS Rating
Input
Current
Output
Floor Loading
at End of Discharging
Dissipation at
Dim
ensions W
xDxH
Unpacked
Voltage
Voltage
(240 Cell,
(240 Cell, 1.67V/cell)
Continuous
100% Load
Nameplate
Nameplate
2.00 V/cell)
kW(BTU/hr)
mm(in)
kg(lbs)
kg/m
2(lb/ft2)
kVA
kW
VAC
VAC
AMP
AMP
AMP
AMP
AMP
3578x830x1872
37.1 (126716)
2297 (5065)
774 (158)
650
591
480
480
763
891
782
1280
1559
(140.9x32.7x73.7)
3578x830x1872
42.8 (146211)
2297 (5065)
774 (158)
750
682
480
480
880
1028
902
1502
1799
(140.9x32.7x73.7)
3578x830x1872
47.1 (160832)
2297 (5065)
774 (158)
825
750
480
480
969
1130
992
1600
1979
(140.9x32.7x73.7)
11/3/08
P/N
110100215-001 Sheet 8 of 10 Rev. 1
!"#$%%%%++
SITE PLANNING DATA
SYSTEM 9395-825 ISBM SEPARATE RECTIFIER FEEDS, M
ODELS 650, 750, 825kV
A, SINGLE M
ODULE
MAINTENANCE BYPASS SWITCHGEAR (OPTION)
AC OUTPUT
MIS
MBP
TO LOAD
UPS M
ODULE
ISBM
BYPASS
AC IN
PUT
MBB
BATTERY
RECTIFIER
AC IN
PUTS
UPM1
UPM2
UPM3
UPM1
UPM2
UPM3
Notes:
ISBM
1. Rectiÿer AC in
put current calculations: Continuous - 100% load without ch
arging; N
ameplate -
9. The UPS cabinet can be in
stalled in
line-up-and-m
atch or standalone conÿgurations.
100% load with m
aximum charging.
10. Top and bottom cable entries through removable access plates are standard for all conÿgurations.
2. Inverter AC output current calculation: N
ameplate - 100% rated output load.
Access plates shall be custom-m
odiÿed to suit conduit sizes.
3. Byp
ass AC in
put current calculation is based on 100% rated output.
11. A
ll wiring is to be in
accordance with National and Local Electric Codes.
4. The system m
ust be in
stalled on a level !oor suitable for computer or electronic equipment.
12. A
C in
put to UPS rectiÿer (0.98 m
in.pF): (3) phases, (1) ground.
5. The system m
ust be in
stalled in
a temperature and humidity controlled in
door area
AC output to load: (3) phases, (1) neutral if required, (1) ground.
free of conductive contaminants.
AC in
put to UPS byp
ass: (3) phases, (1) neutral if required, (1) ground.
6. A
mbient temperature range: 0-40C (32-104F); Recommended operating range: 20-25C (68-77F);
DC in
put from battery to UPS: (1) positive, (1) negative, (1) ground.
Maximum relative humidity: 95% non-condensing.
13. The front panels m
ust be removed to m
eet the 830mm (or 32.7" depth) to ÿt through doors.
7. M
inim
um overhead clearance for ventilation above the UPS cabinet is 457mm (18in.).
14. If the UPS is to be in
stalled with the right side near a wall a m
inim
um of 6" is required betw
een the
8. M
inim
um 915mm (36in.) clearance in
front of the UPS cabinet is required for coolin
g air in
take
wall and the unit. If a battery cabinet is in
stalled to the right of the UPS the 6" are not required.
and servicing space.
15. Speciÿcations are subject to change.
Product Speciÿcations
Battery
Inverter AC
Rectiÿer AC In
put Current
Nameplate
AC
Max. Battery Current
AC
Max. Heat
Approx. W
eight
Output Current
Per UPM
UPS Rating
Input
Floor Loading
Current
Output
at End of Disch
arging
Dissipation at
Dim
ensions WxD
xH
Unpacked
Voltage
Voltage
(240 Cell,
(240 Cell, 1.67V/cell)
Continuous
100% Load
Nameplate
Nameplate
2.00 V/cell)
kW(BTU/hr)
mm(in)
kg(lbs)
kg/m
2(lb/ft2)
kVA
kW
VAC
VAC
AMP
AMP
AMP
AMP
AMP
3578x830x1872
37.1 (126716)
2297 (5065)
774 (158)
650
591
480
480
255
370
782
1280
1559
(140.9x32.7x73.7)
3578x830x1872
42.8 (146211)
2297 (5065)
774 (158)
750
682
480
480
294
370
902
1502
1799
(140.9x32.7x73.7)
3578x830x1872
47.1 (160832)
2297 (5065)
774 (158)
825
750
480
480
323
370
992
1600
1979
(140.9x32.7x73.7)
P/N
110100215-002 Sheet 5 of 7 Rev. 1
!"#$%%%%+.
SITE PLANNING DATA
SYSTEM 9395-825 PLUS 1 ISBM, MODELS 650, 750, 825kVA, SINGLE M
ODULE
MAINTENANCE BYPASS SWITCHGEAR (OPTION)
AC OUTPUT
MIS
MBP
TO LOAD
UPS M
ODULE
ISBM
BYPASS
AC INPUT
MBB
RECTIFIER
CB1 (OPTION)
BATTERY
AC INPUT
UPM1
UPM2
UPM3
UPM4
UPM4
ISBM
UPM1
UPM2
UPM3
Notes:
1. Rectiÿer AC input current calculations: Continuous - 100% load without charging; Nameplate -
9. The UPS cabinet can be installed in line-up-and-m
atch or standalone conÿgurations.
100% load with m
axim
um charging.
10. Top and bottom cable entries through removable access plates are standard for all conÿgurations.
2. Inverter AC output current calculation: Nameplate - 100% rated output load.
Access plates shall be custom-m
odiÿed to suit conduit sizes.
3. Bypass AC input current calculation is based on 100% rated output.
11. All wiring is to be in accordance with National and Local Electric Codes.
4. The system m
ust be installed on a level "oor suitable for computer or electronic equipment.
12. AC input to UPS rectiÿer (0.98 m
in.pF): (3) phases, (1) ground.
5. The system m
ust be installed in a temperature and humidity controlled indoor area
AC output to load: (3) phases, (1) neutral if required, (1) ground.
free of conductive contaminants.
AC input to UPS bypass: (3) phases, (1) neutral if required, (1) ground.
6. Ambient temperature range: 0-40C (32-104F); Recommended operating range: 20-25C (68-77F);
DC input from battery to UPS: (1) positive, (1) negative, (1) ground.
Maxim
um relative humidity: 95% non-condensing.
13. The front panels m
ust be removed to m
eet the 830mm (or 32.7" depth) to ÿt through doors.
7. Minim
um overhead clearance for ventilation above the UPS cabinet is 457mm (18in.).
14. If the UPS is to be installed with the right side near a wall a m
inim
um of 6" is required betw
een the
8. Minim
um 915mm (36in.) clearance in front of the UPS cabinet is required for cooling air intake
wall and the unit. If a battery cabinet is installed to the right of the UPS the 6" are not required.
and servicing space.
15. Speciÿcations are subject to change.
Product Speciÿcations
Battery
Inverter AC
AC
AC
Max. Battery Current
Rectiÿer AC Input Current
Max. Heat
Nameplate
Output Current
Approx. Weight
UPS Rating
Input
Output
at End of Discharging
Dissipation at
Dim
ensions W
xDxH
Floor Loading
Current
Unpacked
Voltage
Voltage
(240 Cell, 1.67V/cell)
Continuous
100% Load
(240 Cell,
Nameplate
Nameplate
2.00 V/cell)
kW(BTU/hr)
mm(in)
kg(lbs)
kg/m
2(lb/ft2)
kVA
kW
VAC
VAC
AMP
AMP
AMP
AMP
AMP
4322x830x1872
37.1 (126716)
2887 (6365)
805 (165)
650
591
480
480
763
891
782
1280
1559
(170.2x32.7x73.7)
4322x830x1872
42.8 (146211)
2887 (6365)
805 (165)
750
682
480
480
880
1028
902
1502
1799
(170.2x32.7x73.7)
4322x830x1872
47.1 (160832)
2887 (6365)
805 (165)
825
750
480
480
969
1130
992
1600
1979
(170.2x32.7x73.7)
11/3/08
P/N
110100215-001 Sheet 9 of 10 Rev. 1
!"#$%%%%+'
SITE PLANNING DATA
SYSTEM 9395-825 PLUS 1 ISBM SEPARATE RECTIFIER FEEDS, MODELS 650, 750, 825kVA, SINGLE M
ODULE
MAINTENANCE BYPASS SWITCHGEAR (OPTION)
AC OUTPUT
MIS
MBP
TO LOAD
UPS M
ODULE
ISBM
BYPASS
AC INPUT
MBB
BATTERY
RECTIFIER
AC INPUTS
UPM1
UPM2
UPM3
UPM4
UPM4
ISBM
UPM1
UPM2
UPM3
Notes:
1. Rectiÿer AC input current calculations: Continuous - 100% load without charging; Nameplate -
9. The UPS cabinet can be installed in line-up-and-m
atch or standalone conÿgurations.
100% load with m
axim
um charging.
10. Top and bottom cable entries through removable access plates are standard for all conÿgurations.
2. Inverter AC output current calculation: Nameplate - 100% rated output load.
Access plates shall be custom-m
odiÿed to suit conduit sizes.
3. Bypass AC input current calculation is based on 100% rated output.
11. All wiring is to be in accordance with National and Local Electric Codes.
4. The system m
ust be installed on a level "oor suitable for computer or electronic equipment.
12. AC input to UPS rectiÿer (0.98 m
in.pF): (3) phases, (1) ground.
5. The system m
ust be installed in a temperature and humidity controlled indoor area
AC output to load: (3) phases, (1) neutral if required, (1) ground.
free of conductive contaminants.
AC input to UPS bypass: (3) phases, (1) neutral if required, (1) ground.
6. Ambient temperature range: 0-40C (32-104F); Recommended operating range: 20-25C (68-77F);
DC input from battery to UPS: (1) positive, (1) negative, (1) ground.
Maxim
um relative humidity: 95% non-condensing.
13. The front panels m
ust be removed to m
eet the 830mm (or 32.7" depth) to ÿt through doors.
7. Minim
um overhead clearance for ventilation above the UPS cabinet is 457mm (18in.).
14. If the UPS is to be installed with the right side near a wall a m
inim
um of 6" is required betw
een the
8. Minim
um 915mm (36in.) clearance in front of the UPS cabinet is required for cooling air intake
wall and the unit. If a battery cabinet is installed to the right of the UPS the 6" are not required.
and servicing space.
15. Speciÿcations are subject to change.
Product Speciÿcations
Battery
Inverter AC
Rectiÿer AC Input Current
Max. Battery Current
AC
AC
Max. Heat
Nameplate
Output Current
Approx. Weight
Per UPM
UPS Rating
Input
Output
Dissipation at
Dim
ensions W
xDxH
Floor Loading
Current
at End of Discharging
Unpacked
Voltage
Voltage
(240 Cell, 1.67V/cell)
Continuous
100% Load
(240 Cell,
Nameplate
Nameplate
2.00 V/cell)
kW(BTU/hr)
mm(in)
kg(lbs)
kg/m
2(lb/ft2)
kVA
kW
VAC
VAC
AMP
AMP
AMP
AMP
AMP
4322x830x1872
37.1 (126716)
2887 (6365)
805 (165)
650
591
480
480
255
370
782
1280
1559
(170.2x32.7x73.7)
4322x830x1872
42.8 (146211)
2887 (6365)
805 (165)
750
682
480
480
294
370
902
1502
1799
(170.2x32.7x73.7)
4322x830x1872
47.1 (160832)
2887 (6365)
805 (165)
825
750
480
480
323
370
992
1600
1979
(170.2x32.7x73.7)
11/3/08
P/N
110100215-002 Sheet 6 of 7 Rev. 1
!"#$%%%%+(
SITE PLANNING DATA
SYSTEM 9395-1100 ISBM, MODELS 1000, 1100kVA, SINGLE M
ODULE
MAINTENANCE BYPASS SWITCHGEAR (OPTION)
AC OUTPUT
MIS
MBP
TO LOAD
UPS M
ODULE
BYPASS
AC INPUT
ISBM
MBB
RECTIFIER
CB1 (OPTION)
BATTERY
AC INPUT
UPM1
UPM2
UPM3
UPM4
UPM4
ISBM
UPM1
UPM2
UPM3
Notes:
1. Rectiÿer AC input current calculations: Continuous - 100% load without charging; Nameplate -
9. The UPS cabinet can be installed in line-up-and-m
atch or standalone conÿgurations.
100% load with m
axim
um charging.
10. Top and bottom cable entries through removable access plates are standard for all conÿgurations.
2. Inverter AC output current calculation: Nameplate - 100% rated output load.
Access plates shall be custom-m
odiÿed to suit conduit sizes.
3. Bypass AC input current calculation is based on 100% rated output.
11. All wiring is to be in accordance with National and Local Electric Codes.
4. The system m
ust be installed on a level "oor suitable for computer or electronic equipment.
12. AC input to UPS rectiÿer (0.98 m
in.pF): (3) phases, (1) ground.
5. The system m
ust be installed in a temperature and humidity controlled indoor area
AC output to load: (3) phases, (1) neutral if required, (1) ground.
free of conductive contaminants.
AC input to UPS bypass: (3) phases, (1) neutral if required, (1) ground.
6. Ambient temperature range: 0-40C (32-104F); Recommended operating range: 20-25C (68-77F);
DC input from battery to UPS: (1) positive, (1) negative, (1) ground.
Maxim
um relative humidity: 95% non-condensing.
13. The front panels m
ust be removed to m
eet the 830mm (or 32.7" depth) to ÿt through doors.
7. Minim
um overhead clearance for ventilation above the UPS cabinet is 457mm (18in.).
14. If the UPS is to be installed with the right side near a wall a m
inim
um of 6" is required betw
een the
8. Minim
um 915mm (36in.) clearance in front of the UPS cabinet is required for cooling air intake
wall and the unit. If a battery cabinet is installed to the right of the UPS the 6" are not required.
and servicing space.
15. Speciÿcations are subject to change.
Product Speciÿcations
Battery
Inverter AC
AC
AC
Max. Battery Current
Rectiÿer AC Input Current
Max. Heat
Nameplate
Output Current
Approx. Weight
UPS Rating
Input
Output
at End of Discharging
Dissipation at
Dim
ensions W
xDxH
Floor Loading
Current
Unpacked
Voltage
Voltage
(240 Cell, 1.67V/cell)
Continuous
100% Load
(240 Cell,
Nameplate
Nameplate
2.00 V/cell)
kW(BTU/hr)
mm(in)
kg(lbs)
kg/m
2(lb/ft2)
kVA
kW
VAC
VAC
AMP
AMP
AMP
AMP
AMP
4322x830x1872
57.1 (194948)
2960 (6525)
825 (169)
1000
909
480
480
1174
1370
1203
2000
2398
(170.2x32.7x73.7)
4322x830x1872
62.8 (214443)
2960 (6525)
825 (169)
1100
1000
480
480
1291
1507
1323
2203
2638
(170.2x32.7x73.7)
11/3/08
P/N
110100215-001 Sheet 10 of 10 Rev. 1
!"#$%%%%+)
SITE PLANNING DATA
SYSTEM 9395-1100 ISBM SEPARATE RECTIFIER FEEDS, MODELS 1000, 1100kVA, SINGLE M
ODULE
MAINTENANCE BYPASS SWITCHGEAR (OPTION)
AC OUTPUT
MIS
MBP
TO LOAD
UPS M
ODULE
ISBM
BYPASS
AC INPUT
MBB
BATTERY
RECTIFIER
AC INPUTS
UPM1
UPM2
UPM3
UPM4
UPM4
ISBM
UPM1
UPM2
UPM3
Notes:
1. Rectiÿer AC input current calculations: Continuous - 100% load without charging; Nameplate -
9. The UPS cabinet can be installed in line-up-and-m
atch or standalone conÿgurations.
100% load with m
axim
um charging.
10. Top and bottom cable entries through removable access plates are standard for all conÿgurations.
2. Inverter AC output current calculation: Nameplate - 100% rated output load.
Access plates shall be custom-m
odiÿed to suit conduit sizes.
3. Bypass AC input current calculation is based on 100% rated output.
11. All wiring is to be in accordance with National and Local Electric Codes.
4. The system m
ust be installed on a level "oor suitable for computer or electronic equipment.
12. AC input to UPS rectiÿer (0.98 m
in.pF): (3) phases, (1) ground.
5. The system m
ust be installed in a temperature and humidity controlled indoor area
AC output to load: (3) phases, (1) neutral if required, (1) ground.
free of conductive contaminants.
AC input to UPS bypass: (3) phases, (1) neutral if required, (1) ground.
6. Ambient temperature range: 0-40C (32-104F); Recommended operating range: 20-25C (68-77F);
DC input from battery to UPS: (1) positive, (1) negative, (1) ground.
Maxim
um relative humidity: 95% non-condensing.
13. The front panels m
ust be removed to m
eet the 830mm (or 32.7" depth) to ÿt through doors.
7. Minim
um overhead clearance for ventilation above the UPS cabinet is 457mm (18in.).
14. If the UPS is to be installed with the right side near a wall a m
inim
um of 6" is required betw
een the
8. Minim
um 915mm (36in.) clearance in front of the UPS cabinet is required for cooling air intake
wall and the unit. If a battery cabinet is installed to the right of the UPS the 6" are not required.
and servicing space.
15. Speciÿcations are subject to change.
Product Speciÿcations
Battery
Inverter AC
Rectiÿer AC Input Current
AC
AC
Max. Battery Current
Max. Heat
Nameplate
Output Current
Approx. Weight
Per UPM
UPS Rating
Input
Output
Dissipation at
Dim
ensions W
xDxH
Floor Loading
Current
at End of Discharging
Unpacked
Voltage
Voltage
(240 Cell, 1.67V/cell)
Continuous
100% Load
(240 Cell,
Nameplate
Nameplate
2.00 V/cell)
kW(BTU/hr)
mm(in)
kg(lbs)
kg/m
2(lb/ft2)
kVA
kW
VAC
VAC
AMP
AMP
AMP
AMP
AMP
4322x830x1872
57.1 (194948)
2960 (6525)
825 (169)
1000
909
480
480
294
370
1203
2000
2398
(170.2x32.7x73.7)
4322x830x1872
62.8 (214443)
2960 (6525)
825 (169)
1100
1000
480
480
323
370
1323
2203
2638
(170.2x32.7x73.7)
11/3/08
P/N
110100215-002 Sheet 7 of 7 Rev. 1
!"#$%%%%+*
