EC centrifugal fans backward curved, single inlet, Ø 560

Highlights: – 7-blade fan, 3-phase fan motor – 10 VDC max. output / 10 mA, 24 V external program input, 0-10 VDC / PWM control input – Integrated PID controller, control interface with SELV potential safely disconnected from the mains, RS485 MODBUS RTU technology – Over-temperature protected electronics / motor – Soft start, PFC passive, line undervoltage / phase failure detectionMaterial: Impeller: Aluminum sheet Rotor: Coated in black Electronic housing: Die-cast aluminum Assembly: Galvanized steel with aluminum postsMounting position: Shaft horizontal or rotor on bottom; rotor on top on request Condensate discharge holes: Rotor-side Direction of rotation: Clockwise, seen on rotor

(1) Nominal data at maximum load.

Measurement: LU-128639

Air performance measured as per: ISO 5801, Installation category A, without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LPA measured at 1m distance to fan axis. The values given are valid under the measuring conditions mentioned and may vary accoring to the actual installation situation. With any deviation to the standard set-up, the specific values have to be checked and reviewed once installed or fitted.

For detailed information on the measuring set-up, please contact ebm-papst.

Curvesn

rpm

Pe

W

I A

(460V)

I A

(230V)

LwAin

dB(A)

Nominal Data Air fl

ow

Nom

inal

vol

tage

rang

e

Freq

uenc

y

Pow

er in

put (

1)

Spee

d (1

)

Curr

ent d

raw

(1)

Tem

pera

ture

rang

e (1

)

Mas

s

Ingr

ess

prot

ectio

n ra

ting

Elec

trica

l wiri

ng d

iagr

am

UL

Type RadiPac Motor CFM VAC Hz Watts RPM A °C lbs

R3G560-AQ11-19F EG1R-240-560-60 M3G150-NA 10,113 200...240 50/60 4,500 1,750 12.2 -25...40 88 IP54 B Yes

R3G560-AQ04-09F EG1R-480-560-60 M3G150-NA 10,113 380...480 50/60 4,700 1,750 6.3 -25...40 88 IP54 B Yes

0 2.000 4.000 6.000 8.000 9.000 cfm

0

0

.4

0.8

1.2

1.6

2

2.

4

2

.8

3

.2

3

.6

4

4.4

4.8

5.

2

5

.6

in. w

g

2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 m3/h

pfs[Pa]

pfs[Pa]

pfs[Pa]

1400

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

0

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1750 3032 4.1 8.3 97

1750 3929 5.3 11.2 91

1750 4700 6.3 12.2 84

1750 4366 5.8 11.9 86

1450 1675 2.3 4.6 93

1450 2171 2.9 5.9 87

1450 2602 3.5 7.3 80

1450 2432 3.3 7.0 82

1150 836 1.1 2.3 88

1150 1083 1.5 3.0 82

1150 1298 1.7 3.7 75

1150 1213 1.6 3.5 76

EG1R-XXX-560-60

R3G560-AQXX-XXF

19.65(499)

24.8

03 ( 6

30)

29.528 (750)Ø .433 (11)8 PLACES

31.4

96 ( 8

00)

17.874(454)

22.9(582)

Depth of screw max. 20 mm

Cable diameter: min. 9 mm,max. 16 mm;tightening torque: 6±0.9 Nm

Tightening torque 3.5±0.5 Nm

Ø10.75 (273)Ø11.97 (304 ±0.5)

Ø12.76 (324)

Cable diameter: min. 4 mm,max. 10 mm;

tightening torque: 4±0.6 Nm Accessory part: inlet nozzle 64030-2-4013with a pressure tap not included in the standarscope of delivery; other inlet nozzles on request

4.45 (113)

6.3 (160)9.41 (239)

15.43 (392±2)

0.63(16)

0.08 (2)3.23(82)

Ø15.

55 (3

95)

Ø25.

04 (6

36)

Ø15.

16 (3

85)

Ø14.

96 (3

80)

Ø19.

29 (4

90)

Ø20.

28 (5

15)

Ø0.3

5 (9

(6x)

)

( )

Dimensions shown in inches (mm)

Dimensions shown in inches (mm)