Edition 04-2010 • EAME John Deere Werke Mannheim · avoid dirt on your tractor and following...

FENDER, SIDE EXTENSIONS, MUD GUARDS

5020, 5M, 5R, 5000, 5010, 5015, 5G,6000, 6010, 6020, 6030, 6030 Premium, 7030 & 7030 E Premium,7000, 7010, 7020, 7030, 8000, 8010, 8020, 8030, 8R Series

John Deere Werke MannheimEdition 04-2010 • EAME

TRACTORS

John Deere Werke Mannheim - Parts Marketing - EAME Edition - Status 05-2010 2

TURNABLE and RIGID FRONT fenders,REAR fenders, REAR Fender side extensions,

Mud flaps, Mud guards

CATALOGUE INDEX

TRACTOR SERIES PAGE

6020 & SE, 6030, 6030 Premium, 7030 Premium, 7030 E Premium.................. 3-8

6000, 6010........................................................................................................... 9-12

5020, 5M, 5R.…………………………………………………………………………. 13-14

5000 & N, 5010 & N, 5015, 5015 F&V, 5G, 5GH, 5G F&V………………………. 15-18

7000, 7010, 7020, 7030, 8020, 8030, 8R……………………………..................... 19-24


Front fenders, rear fenders, side extensions, mud guards6020 & SE, 6030, 6030 Premium, 7030 Premium, 7030 E Premium Series tractors

FRONT FENDERS - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.

For safer high speed roadtransport and reduced tractorsoiling. Large, full-coveragefront fenders are available with awide range of adjustments toadapt to the different treadsettings to protect the cab frommud and debris.

Description Tractor Series Part No.

W 265 mm, L 1000 mm - RH or LH (2WD) 6020 & SE, 6015, 6030, 6025 AL180331

W 320 mm, L 1070 mm - RH or LH (MFWD) 6020 & SE, 6015 AL180328

W 370 mm, L 1280 mm - RH or LH (MFWD) 6020 & SE, 6015, 6030, 6030 Premium,6025, 7030 & 7030 E Premium AL180330


W 420 mm, L 1315 mm - RH or LH (MFWD) 6020 & SE AL180329




W = Width, L = Length

Length

Width


TURNABLE FRONT FENDERS - FIELD INSTALLATION KITSKits include turnable front fenders (RH & LH) plus the necessary hardware for field installation.

Turnable front fenders allow a better steering angle - for easier and fasterturning e.g. on the headland - and therefore significantly bettermanoeuvrability of the tractor.

Please find on the next page more information regarding front fender widths andcorresponding tyre sizes.

Description Tractor Series Part No. Remark

W 370 mm, L 1280 mm 6020 & SE, 6015, 6030, 6030 Premium, 6025,7030 & 7030 E Premium AL205773





For tractors with frontloader, please orderin addition if required:

Fender stop panel4 cyl.: 1 x AL1653356 cyl.: 1 x AL165336

Conversion kit fromRIGID to TURNABLE front fenders

- with MFWD axle 730: 6020-6220- with MFWD axle 730: 6320-6420S, 6020SE-6420SE- with MFWD axle 740: 6520 & SE, 6620 & SE- with MFWD axle 745/750: 6820-6920S- for tractors with MFWD: 6030 Premium, 7030 & 7030 E Premium

AL205783

Depending on thetractor optionsadditional parts maybe required, pleasecheck correspondingparts catalogue.


RIGID FRONT FENDERS - FIELD INSTALLATION KITSKits include rigid front fenders (RH & LH) plus the necessary hardware for field installation.

Please find on the next page more information regarding front fender widths and corresponding tyre sizes.


W 265 mm, L 1000 mm (2WD only) 6020 & SE, 6015, 6030, 6025 AL180215

Base mounting kit for rigid front fenders (MFWD) 6020 & SE, 6015 AL71218

W 370 mm, L 1280 mm (MFWD) 6020 & SE, 6015, 6030, 6030 Premium, 6025 AL180095







Overview of TURNABLE front fender widths in combination with corresponding tyre sizes

TURNABLEfender width Tyre sizes

370 mm4 cyl.: 11.2R24, 280/85R24, 12.4R24, 320/85R24, 13.6R24, 340/85R24, 11.2R28, 280/85R28, 12.4R28,320/85R28, 13.6R28, 340/85R28

6 cyl.: 13.6R24, 340/85R24, 12.4R28, 320/85R28, 13.6R28, 340/85R28

420 mm4 cyl.: 380/70R24, 14.9R24, 380/85R24, 420/70R24, 380/70R28, 14.9R28, 380/85R28, 420/70R28

6 cyl.: 14.9R24, 380/85R24, 420/70R24, 380/70R28, 14.9R28, 380/85R28, 420/70R28

480 mm4 cyl.: 440/65R24, 480/65R24, 16.9R24, 420/85R24, 480/70R24, 480/65R28

6 cyl.: 480/65R24, 16.9R24, 420/85R24, 480/70R24, 480/65R28, 16.9R28, 420/85R28, 480/70R28,16.9R30, 420/85R30, 480/70R30

540 mm4 cyl.: 540/65R24, VF 520/60R28

6 cyl.: 540/65R24, VF 520/60R28, 540/65R28, 540/65R30, 540/75R28

620 mm 6 cyl.: VF 600/60R28, 600/65R28, VF 600/60R30

Overview of RIGID front fender widths in combination with corresponding tyre sizes

RIGIDfender width Tyre sizes

370 mm4 cyl.: 280/70R16, 10.5/80-18, 11.2R24, 280/85R24, 12.4R24, 320/85R24, 13.6R24, 340/85R24, 11.2R28,280/85R28, 12.4R28, 320/85R28, 13.6R28, 340/85R28

6 cyl.: 13.6R24, 340/85R24, 12.4R28, 320/85R28, 13.6R28, 340/85R28

420 mm4 cyl.: 380/70R24, 14.9R24, 380/85R24, 420/70R24, 380/70R28, 14.9R28, 380/85R28, 420/70R28

6 cyl.: 14.9R24, 380/85R24, 420/70R24, 380/70R28, 14.9R28, 380/85R28, 420/70R28

480 mm4 cyl.: 440/65R24, 480/65R24, 16.9R24, 420/85R24, 480/70R24, 480/65R28

6 cyl.: 480/65R24, 16.9R24, 420/85R24, 480/70R24, 480/65R28, 16.9R28, 420/85R28, 480/70R28,16.9R30, 420/85R30, 480/70R30

540 mm4 cyl.: 540/65R24, VF 520/60R28

6 cyl.: 540/65R24, VF 520/60R28, 540/65R28, 540/65R30, 540/75R28

620 mm 6 cyl.: VF 600/60R28, 600/65R28


REAR FENDERS - INDIVIDUAL PARTSAdditional parts are required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.


Rear fender - RH6020 & SE,6030, 6030 Premium,7030 & 7030 E Premium

AL168326

Rear fender - LH6020 & SE,6030, 6030 Premium,7030 & 7030 E Premium

AL168325

REAR FENDER SIDE EXTENSIONS - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.

Rear fender side extensions tractors provide…

Protection from mud, stones and debrisProtection to avoid dirt on your tractor and on the followingvehiclesBetter visibility through clear windowsCoverage also of large tyresAn easy installation in a few work steps

The extensions can be combined with snow chains on rear wheels,for example for forestry applications.

Description Tractor Series Tyre size Part No.

110 x 15 mm - RH L200789

110 x 15 mm - LH

cab only: 6020 & SE,6030, 6030 Premium,7030 & 7030 E Premium

18.4R30,16.9R34, 420/85R34, 480/70R34,13.6R38, 18.4R38, 460/85R38 L200788

110 x 60 mm - RH L200784

110 x 60 mm - LH


16.9R30, 18.4R30,16.9R34, 18.4R34, 480/70R34,13.6R38, 14.9R38, 16.9R38, 420/85R38, 18.4R38,460/85R38, 480/70R38, 520/70R38, 540/65R38 L200783

200 x 20 mm - RH L200797

200 x 20 mm - LH


520/70R38, 20.8R38, 520/85R38, 580/70R38,600/65R38, 650/65R38 L200793

190 x 65 mm - RH L200787

190 x 65 mm - LH


520/70R34,520/70R38, 20.8R38, 520/85R38, 540/65R38,600/65R38, 650/65R38 L200785

Rear fender

Side extension


REAR FENDER SIDE EXTENSIONS - FIELD INSTALLATION KITSKits include side extensions (RH & LH) plus the necessary hardware for field installation.

Description Tractor Series Tyre size Part No.

110 x 15 mm - RH & LH cab only: 6030, 6030 Premium,7030 & 7030 E Premium 18.4R38, 460/85R38 AL174767

110 x 60 mm - RH & LH cab only: 6030, 6030 Premium,7030 & 7030 E Premium

18.4R30,16.9R34, 18.4R34, 480/70R34,13.6R38, 14.9R38, 16.9R38, 420/85R38,18.4R38, 460/85R38, 480/70R38,520/70R38, 540/65R38

AL174768


520/70R38, 20.8R38, 520/85R38,580/70R38, 600/65R38, 650/65R38 AL174769


520/70R34,520/70R38, 20.8R38, 520/85R38,540/65R38, 600/65R38, 650/65R38

AL174770

Mounting partsfender side extensions& mud guards

Order in addition, if required. AL120094

MUD FLAP FOR REAR FENDERS - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.

Additional mud flaps significantly reduce the amount of spray and mudthrown up by the rear wheel. They provide additional protection toavoid dirt on your tractor and following vehicles which is especiallyimportant for heavy duty work and bad weather conditions. The resultis a cleaner cab and better operator visibility.

Description Tractor Series Part No. Remarks

Mud flap - RH or LH cab only: 6020 & SE, 6030,6030 Premium, 7030 & 7030 E Premium L156612

Can be combined with side extension:- 190 x 65 mm- 190 / 200 x 20 mm

MUD FLAPS FOR REAR FENDERS - FIELD INSTALLATION KITKit includes mud flaps (RH & LH) plus the necessary hardware for field installation.


2 mud flaps -rear fenders

cab only: 6020 & SE,6030, 6030 Premium,7030 Premium,7030 E Premium

AL159975Can be combined withside extension:- 190 x 65 mm- 190 / 200 x 20 mm

Mud flap


MUD GUARDS FOR STEPS - INDIVIDUAL PARTSAdditional parts are required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.

Mud guards for steps extend the coverageoffered by the rear fenders. They are madefrom rugged material and protect the stepsfrom mud and debris.


Mud guard - RH L116671

Mud guard - LH4 cyl. models without suspended cab: 6020 & SE, 6030, 6030 Premium

L116670


Mud guard - LH

4 cyl. models with suspended cab: 6020, 6030 Premium

all 6 cyl. cab models: 6020 & SE, 6030, 6030 Premium, 7030 & 7030 E Premium L116672

MUD GUARDS - FIELD INSTALLATION KITSKits include mud guards (RH & LH) plus the necessary hardware for field installation.


Mud guards - RH & LH 4 cyl. models without suspended cab: 6030, 6030 Premium AL174141

Mud guards - RH & LH4 cyl. models with suspended cab: 6030 Premium

all 6 cyl. cab models: 6030, 6030 Premium, 7030 & 7030 E PremiumAL174142

Mounting parts - fender sideextensions & mud guards Order in addition, if required. AL120094


Front fenders, rear fenders, side extensions, mud flaps, mud guards6000, 6010 Series tractors



W 265 mm, L 1000 mm - RH or LH (2WD) 6000 & SE, 6010 & SE, 6005 AL180331

W 320 mm, L 1070 mm - RH or LH (MFWD) 6000, 6010 AL180328

W 370 mm, L 1280 mm - RH or LH (MFWD) 6000 & SE, 6010 & SE AL180330

W 420 mm, L 1440 mm - RH or LH (MFWD) 6000 & SE, 6010 & SE, 6005 AL180327








W 370 mm, L 1280 mm - RH & LH 6000 & SE, 6010 & SE AL205773

W 420 mm, L 1440 mm - RH & LH 6000 & SE, 6010 & SE, 6005 AL205774

W 480 mm, L 1440 mm - RH & LH 6000 & SE, 6010 & SE, 6005 AL205776

W 540 mm, L 1540 mm - RH & LH 6000 & SE, 6010 & SE AL205779



REAR FENDERS - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.

Description Tractor Models Part No. Remark

A Rear fender - RH L101648 with registration plate

A Rear fender - LHcab only: 6000, 6010

L101649 without registration plate

A Rear fender - RH L101643 without registration plate

A Rear fender - LHcab only: 6000, 6010

L101642 with registration plate

A Rear fender - RH L110271 with registration plate

A Rear fender - LH6000SE, 6010SE

L110272 without registration plate

A Rear fender - RH L110885 without registration plate

A Rear fender - LH6000SE, 6010SE

L110884 with registration plate

A Rear fender - RH L110885

A Rear fender - LH

with 2-post roll-guard:6010 L110272

B Rear fender - RH L79685

B Rear fender - LHwith 2-post roll-guard:6000, 6010 L79683

C Rear fender - RH L77510

C Rear fender - LH6000 & SE, 6010 & SE

L77511

RIGID FRONT FENDERS - FIELD INSTALLATION KITSKit includes rigid front fenders (RH & LH) plus the necessary hardware for field installation.


W 265 mm, L 1000 mm (2WD) 6000 & SE, 6010 & SE, 6005 AL180215

Base mounting kit for rigid front fenders (MFWD) 6000 & SE, 6010 & SE, 6005 AL71218


CB




A Side extension - RH L101638

A Side extension - LHcab only: 6000 & SE, 6010 & SE

L101534

B Side extension - LH or RH cab only: 6000 & SE, 6010 & SE L101609

C Additional side extension - extra wide, LH or RHonly in combination with A or B

cab only: 6000, 6010 & SE L110877



Mud flap - RH cab only: 6000, 6010 & SE L110876

Mud flap - LH cab only: 6000, 6010 & SE L110875

For tractors with fender sideextensions (A or B see above)already installed.

MUD FLAP KIT FOR REAR FENDERS - FIELD INSTALLATION KITKits include mud flaps (RH & LH) plus the necessary hardware for field installation.


2 mud flaps -rear fenders

cab only: 6000, 6010 & SE AL81709For tractors with fender sideextensions (A or B see above)already installed.

B

AC

Mud flap

Side extensionalready installed


MUD FLAPS FOR REAR FENDERS / EXTRA WIDE - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.


Mud flap, extra wide - RH L110611

Mud flap, extra wide - LH

cab only:6000, 6010 & SE

L110610

These mud flaps are recommended if oneside extension, plus the additional sideextension L110877 are already installed oneach fender.

MUD GUARDS FOR STEPS - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.



Mud guard - LH

4 cyl. cab models:6000, 6010 & SE

L111348


Mud guard - LH

6 cyl. cab models:6000, 6010 & SE L111349


Front fenders, rear fenders, side extensions5020, 5M, 5R Series tractors



W 320 mm, L 1070 mm - RH or LH 5020 AL180328

W 370 mm, L 1280 mm - RH or LH 5020, 5M, 5R AL180330


W 420 mm, L 1315 mm - RH or LH 5020 AL180329






5020, 5R LG102498W 370 mm, L 1280 mm

5M LG102655

5020, 5R LG102500W 420 mm, L 1440 mm

5M LG102657

5020, 5R LG102502W 480 mm, L 1440 mm

5M LG102659

Conversion kit from rigid to turnable front fenders 5M LG102420





Base mounting kit for rigid front fenders 5020 LG100707

5020, 5R LG102499W 370 mm, L 1280 mm

5M LG102656

5020, 5R LG102501W 420 mm, L 1440 mm

5M LG102658

W 480 mm, L 1440 mm 5020, 5R LG102503



Overview of front fender widths in combination with corresponding tyre sizes

Front fender width Tyre sizes

370 mm 375/70R20, 14.9R20, 360/70R24, 12.4R24, 320/85R24, 280/85R24, 11.2R24, 320/70R24,11.2R28, 280/85R28

420 mm 13.6R24, 340/70R24, 380/70R24

480 mm 420/65R24, 440/65R24



RH R252621

LH5020, 5M, 5R

R252619

RH RE259007

LH

vineyard tractorversion only: 5020;

5RN RE259006



RH SU293837

LH5020, 5M, 5R

R180912

REAR FENDER SIDE EXTENSIONS - FIELD INSTALLATION KITKit includes rear fender side extensions (RH & LH) plus the necessary hardware for field installation.


RH & LH 5020, 5M, 5R LG100448

Side extension

Rear fender


Front fenders, rear fenders, side extensions5000 & N, 5010 & N, 5015, 5015 F&V, 5G, 5GH, 5GF, 5GV Series tractors



2WD - RH or LH5000, 5000N, 5010, 5010N,

5015, 5015 F&V,5G, 5GH, 5G F&V

ER123947

4WD - RH or LH 5000N, 5010N,5015 F&V, 5G F&V ER124744

4WD - RH or LH 5000, 5010,5015 with rigid fenders ER191744

4WD - RH or LH 5015 with turnable fender,5G, 5GH ER200934



4WD 5015, 5G, 5GH ER067610 includes fender ER200934



2WD 5000, 5010, 5015,5G, 5GH ER066408 includes fender ER123947

2WD 5000N, 5010N,5015 F&V, 5G F&V ER066436 includes fender ER123947

4WD 5000, 5010, 5015 ER066472 includes fender ER191744

4WD 5000N, 5010N,5015 F&V, 5G F&V ER066437 includes fender ER124744



Description Type Tractor Series Part No.

A up to serial no. 007484: 5300, 5400 ER136517RH or LH

A from serial no. 007485: 5300, 5400;5500 ER190245

RH A ER195327

LH Aup to serial no. 105113: 5010 & HC

ER195326

RH or LH A from serial no. 105114: 5010 & HC ER203125

RH A ER190327

LH A5000N, 5010N

ER190328

RH A ER200704

LH A5015 & HC

ER200705

A ER209462RH

B5G, 5GH

ER372463

A ER209463LH

B5G, 5GH

ER372464

RH A ER208499

LH A5G F&V

ER208500

Rear fender Shown on 5015 SeriesType A Rear fender

Type BRear fenderType A

Shown on 5G Series

Type B

Type A



Description Tyres Tractor Series Part No.

125 mm - RH or LH, rigid 5300, 5400 ER135398

200 mm - RH or LH, rigid 5500; 5010 ER190243

190 mm - RH or LH, rigid 5015 ER200566

180 mm - RH, rigid ER209724

180 mm - LH, rigid5G, 5GH

ER209725

145 mm - RH, rigid 24” ER195272

145 mm - LH, rigid 24” ER195273

145 mm - RH, rigid 28” ER195075

145 mm - LH, rigid 28” ER195076

175 mm - RH, rigid 20” ER195274

175 mm - LH, rigid 20”

5000SN, 5010SN, 5015 V, 5GV

ER195275

205 mm - LH, rigid 24“ ER195848

205 mm - RH, rigid 24” ER195849

205 mm - LH, rigid 28” ER195850

205 mm - RH, rigid 28”

5000N, 5010N, 5015 F, 5GF

ER195851

100 mm - RH, rubber 28“ ER195276

100 mm - LH, rubber 28“5000SN, 5010SN, 5015 V, 5G F&V

ER195277

205 mm - RH or LH, rubber 28” 5000N, 5010N & SN, 5015 F ER125167

Rear fender side extensionShown on 5G Series


REAR FENDER SIDE EXTENSIONS - FIELD INSTALLATION KITKit includes rear fender side extensions (RH & LH) plus the necessary hardware for field installation.

Description Tyres Tractor Series Part No. Remarks

125 mm - RH & LH, rigid 5300, 5400 ER066410 includes side extensions2 x ER135398

200 mm - RH & LH, rigid 5500; 5010 ER066464 includes side extensions2 x ER190243

190 mm - RH & LH, rigid 5015 ER067608 includes side extensions2 x ER200566

180 mm - RH & LH, rigid 5G, 5GH ER067871 includes side extensionsER209724, ER209725

145 mm - RH & LH, rigid 24“ 5010SN ER067550 includes side extensionER195272, ER195273

145 mm - RH & LH, rigid 28“ 5010SN ER067551 includes side extensionsER195075, ER195076

175 mm - RH & LH, rigid 20“ 5010SN ER067549 includes side extensionER195274, ER195275

205 mm - RH & LH, rigid 24“ 5010N ER067552 includes side extensionsER195848, ER195849

205 mm - RH & LH, rigid 28” 5010N ER067553 includes side extensionsER195850, ER195851

100 mm - RH & LH, rubber 28” 5000SN, 5010SN,5015 V, 5G F&V ER067554 includes side extensions

ER195276, ER195277

205 mm - RH & LH, rubber 28” 5000N, 5010N,5015 F ER065699 includes side extensions

2 x ER125167


Front fenders, rear fenders, side extensions, mud guards7000, 7010, 7020, 7030, 8000, 8010, 8020, 8030 and 8R Series tractors


Description Tractor Series Part No. Remark Order through

W 394 mm - RH or LH 7000, 7010, 8000with 2WD only

AR86406 EPDC

W 480 mm - RH or LH 7000, 7010, 7020 R192450 7020: up to serial no. 032704

W 480 mm - RH or LH 8000, 8010, 8020 R191189 8020: up to serial no. 015456

W 480 mm - RH 7020, 7030,8020, 8030, 8R RE223407

W 480 mm - LH 7020, 7030,8020, 8030, 8R RE223406

7020: from serial no. 032705


EPDC

W 620 mm - RH 7000, 7010, 7020,8000, 8010, 8020 R192452

W 620 mm - LH 7000, 7010, 7020,8000, 8010, 8020 R192451

7020: up to serial no. 032704

8020. up to serial no. 027762

W 620 mm - RH 7020, 7030,8020, 8030, 8R RE223409

W 620 mm - LH 7020, 7030,8020, 8030, 8R RE223408



EPDC

W = Width

2WD FRONT FENDERS - FIELD INSTALLATION KITSKits include front fenders (RH & LH) plus the necessary hardware for field installation.

Description Tractor Series Part No. Order through

394 mm - RH & LH 7000, 7010 RE67850

394 mm - RH & LH 8000 RE67851EPDC

W = Width


DELUXE TURNABLE FRONT FENDERS - FIELD INSTALLATION KITSKits include turnable front fenders (RH & LH) plus the necessary hardware for field installation.


W 480 mm - RH & LH 7020 RE211530 7020: up to serial no. 032704

W 480 mm - RH & LH 7020, 7030 RE238910 7020: from serial no. 032705


W 620 mm - RH & LH 7020, 7030 RE238909 7020: from serial no. 032705

CompleteGoods /JDMINT


W 480 mm - RH & LH 8020, 8030 RE236666 8020. from serial no. 0154578030: up to serial no. 007241

W 480 mm - RH & LH8030, 8R

with 1300 SeriesMFWD front axle only

RE260608 8030: from serial no. 007242

W 480 mm - RH & LH8030, 8R


RE308214

W 480 mm - RH & LH 8020, 8030, 8Rwith ILS*) only

RE236667



W 620 mm - RH & LH 8020, 8030 RE236669 8020: from serial no. 0277638030: up to serial no. 007241

W 620 mm - RH & LH8030, 8R

with 1300 SeriesMFWD axle only

RE260609 8030: from serial no. 007242


W 620 mm - RH & LH8030, 8R


RE308215 CompleteGoods /

*) ILS = Independent Link Suspension; W = Width




RH 7000 R110834

LH 7000 R110835EPDC

RH 7010 R131968

LH 7010 R131969 without remote PTO

LH 7010 R176979 with remote PTO

EPDC

RH 8000 R111888

LH 8000 R111887up to serial no. 009999

RH 8000, 8010 R131966

LH 8000, 8010 R131967from serial no. 010000

EPDC

RH - without fender extension installed 7020, 7030,8020, 8030 R162233

LH - without fender extension installed 7020, 7030,8020, 8030 R162234

EPDC

RH - with fender side extension installed(2.50 m width)

7020, 7030,8020, 8030 R163025

LH - with fender side extension installed(2.50 m width)

7020, 7030,8020, 8030 R163026

EPDC

RH - without fender extension installed 8R R261776

LH - without fender extension installed 8R R261771EPDC

RH - with fender side extension installed(2.50 m width) 8R R261777

LH - with fender side extension installed(2.50 m width)

8R R261772EPDC

Rear fender




RH 7000 R114745

LH 7000 R106378EPDC

RH 8000 R122008

LH 8000 R122007up to serial no. 009999 EPDC

RH - 2.30 m width 7010, 8000, 8010 R130503

LH - 2.30 m width 7010, 8000, 8010 R130504

RH - 2.50 m width 7010, 8000, 8010 R130505

LH - 2.50 m width 7010, 8000, 8010 R130506

from serial no. 010000 EPDC

RH - 2.50 m width 7020, 8020, 8030 R162235

LH - 2.50 m width 7020, 8020, 8030 R162236EPDC

RH 7030 R237642

LH 7030 R237645EPDC

RH 8R R274563

LH 8R R274562EPDC

RH 8R R282099

LH 8R R282098

with pre-drilled holes forattaching the extra width

extensions R274564, R274565EPDC

REAR FENDER SIDE EXTENSIONS - FIELD INSTALLATION KITSKits include side extensions (RH & LH) plus the necessary hardware for field installation.


7020, 8020, 8030 RE210326 includes side extensionsR162235, R162236

7030 RE253151 includes side extensionsR237642, R237645RH & LH - 2.50 m width

8R RE293506 includes side extensionsR274563, R274562

Complete Goods /JDMINT

Rear fender side extension (2.50 m width)7030 Series shown Rear fender side extension

(2.50 m width) - 7010 Series shown


ADDITIONAL REAR FENDER SIDE EXTENSIONS / EXTRA WIDE - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.


7030, 8030 R233543B - extra wide - RH2.75 m width

8R R274565

7030, 8030 R233544B - extra wide - LH2.75 m width

8R R274564

The additional side extensions B canonly be installed in combination with

side extensions A (see photo above).

If total vehicle width exceeds 2.55 m,extremity lighting is required (also

depending on national regulations).

Please check the corresponding

EPDC

ADDITIONAL REAR FENDER SIDE EXTENSIONS / EXTRA WIDE - FIELD INSTALLATIONKit includes additional side extensions (RH & LH) plus the necessary hardware for field installation.


7030, 8030 RE253154

B - extra wide - RH & LH2.75 m width

8R RE293505

The additional side extensions B canonly be installed in combination with

side extensions A (see photo above).

If total vehicle width exceeds 2.55 m,extremity lighting is required (also

depending on national regulations).

Please check the correspondingparts catalogue for more details.

EPDC

B - Additionalfender sideextension -

extra wide (2.75 m)

A - Fender sideextension (2.50 m)


MUD GUARDS FOR STEPS - INDIVIDUAL PARTSAdditional parts may be required, e.g. rivets, washers, screws. Please check the corresponding parts catalogue for more details.


Mud guard - RH 7020, 7030, 8030 RE205744

7020, 7030, 8030 RE205743Mud guard - LH

8R RE307601

EPDC

MUD GUARD FOR STEPS - FIELD INSTALLATION KITKit includes mud guard (LH) plus the necessary hardware for field installation.


7020, 7030 RE215510 Complete Goods /JDMINTMud guard for LH step

8R RE267353 EPDC



Mud flap - RH R118067

Mud flap - LH7000, 7010

R118068EPDC

Date post:	27-Jul-2018
Category:	Documents
Upload:	nguyendat
View:	213 times
Download:	0 times

Edition 04-2010 • EAME John Deere Werke Mannheim · avoid dirt on your tractor and following...

Documents