Date post: | 24-Oct-2015 |
Category: |
Documents |
Upload: | jonathan-thomas |
View: | 414 times |
Download: | 0 times |
Roo� ng & CladdingCatalogueFastening systems for roo� ng, cladding and general constructions
Imprint
Editor:
EJOT Baubefestigungen GmbH
57334 Bad Laasphe, Germany
Layout and Realisation:
EJOT Baubefestigungen GmbH,
57334 Bad Laasphe, Germany
Print:
Vorländer GmbH & Co. KG, 57072 Siegen, Germany
Legal Notes
EJOT products are constantly enhanced. We reserve the
right to make changes to the technical specifi cations as well
as changes to the product range,
During planning and use of our products please comply with
accepted engineering rules, planning laws as well as relevant
safety regulations. The national technical approvals granted
to our products can be downloaded on the Internet at
www.ejot.com.
General terms and conditions:
Our general terms and conditions can also be found at
www.ejot.com (footer: GTCT)
© 2011 by EJOT Baubefestigungen GmbH
EJOT®, ejotherm®, Delta PT® und PT® are registered
trademarks of EJOT GmbH & Co. KG.
CRONIMAKS®, Corremaks®, EJOFAST®, Dabo®, ECOmate®
FR-variotool® and Solar Ready® are registered trademarks of
EJOT Baubefestigungen GmbH.
DEKTITE® is a registered trademark of Deks Industries
Pty. Ltd., Bayswater Victoria, AU.
TORX®, TORX PLUS® und AUTOSERT® are registered
trademarks of Acument Intellectual Properties, LLC,
Troy Mich., US.
Cover:
Turning Torso, Malmö, Sweden, © iStockphoto
Architect: Santiago Calatrava, Spain
Supplied by EJOT Baubefestigungen GmbH:
EJOT® SUPER-SAPHIR self-drilling screw JT3
Your contact:
www.ejot.com
3
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
C o n t e n t s
Sel
f-ta
ppin
g sc
rew
sS
peci
alsc
rew
s
(Aer
ated
) co
ncre
te
scre
ws
Riv
ets
Sel
f-dr
illi
ng
scre
wsSide lap screw EJOFAST® JF2
(steel) ...................................... p. 38Self-drilling screw JT2 (steel) ...................................... p. 38
Side lap screw EJOFAST® JF3 (A2 stainless steel + steel) ........ p. 53Self-drilling screw JT3 (A2 stainless steel + steel) ........ p. 53
Self-drilling screw JT4 (A2 stainless steel) ................... p. 67
Self-tapping screw JA2 / JZ2 (steel) ...................................... p. 76Self-tapping screw JA3 / JZ3 (A2 stainless steel) ................... p. 78
Self-tapping screw Corremaks® JA1 / JZ1 (A5 stainless steel – 1.4529)............................................... p. 82
Self-tapping screwCRONIMAKS® JZ7 (A2 stainless steel)up to S 355 / St 52 ................... p. 83
Self-drilling screwsApplication advice .................. p. 6 Information ............................. p. 8 Service
Self-tapping screws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
Sca
ffol
ding
fast
ener
sP
ipe
flas
hing
s
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Sto
rmw
ashe
rs
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Inst
alla
tion
tool
sD
irec
tFa
sten
ing
Acc
esso
ries
Storm washer trapeze .......... p. 86Storm washer corrugation .... p. 87
Self-tapping screw BS-R (steel Climadur coated) ............. p. 90Self-tapping screw JA3/JB3/JZ3 (A2 stainless steel) ................... p. 91
Self-tapping screw Duro PT(A2 stainless steel) ................... p. 95Chip board screw SH2 (steel, Climadur coated) ............ p. 97
Chip board screw SH3 / SH3-S(Edelstahl A2) ........................... p. 97PT® Screw Type DG (for glass facades) .................... p. 99
Blind rivet Al/E .................... p. 102Blind rivet Al/V .................... p. 102Blind rivet K14-Al/E ............. p. 102Closed end rivet Al/E ........... p. 103
Closed end rivet Al/V ........... p. 103Bulb-tite rivet ...................... p. 104Drive rivet Al/E .................... p. 104
Shot � ring tool P 525 L+ Accessoires ........................ p. 109Shot � ring tool P 560+ Accessoires ........................ p. 110
Cartridges ........................... p. 111Tie pins ................................ p. 111
Scaffolding anchor JA3-GT p. 113Scaffolding anchorJA3-GU . p. 114 Scaffolding anchor JZ3-GT . p. 113Scaffolding anchor JZ3-GU . p. 114
Ring bolt M10 ...................... p. 113GU Ring bolt M14 ................. p. 115GU-threaded sleeve .............p. 115
Dektite® Combo................... p. 117Dektite® Square .................. p. 118Dektite® EZi Seal ................. p. 119Dektite® Soaker .................. p. 120
Dektite® Retro� t .................. p. 121Dektite® Strip Flash ............ p. 122Accessories ......................... p. 123
Dabo® A/F 8 R(steel, Climadur coated) ...........p. 128Dabo® A/F 8 RT(steel, Climadur coated) ...........p. 129
Dabo® TKR(steel, Climadur coated) ...........p. 130Dabo® TKE(A4 stainless steel) ..................p. 133
Dabo® VHT-R(steel Climadur coated) ............p. 132
Metal stress plate HTV ........ p. 134Metal stress plater HTV-TK . p. 134Metal stress plate HTV-F ..... p. 135Metal stress plate HTV RU ... p. 135
Plastic tube washer HTK ...................................... p. 136Plastic tube washer HTK-M (collated) ................... p. 137
Plastic tube washer EcoTek ................................. p. 136Flat roo� ng anchor FDD ...... p. 138
Concrete screw FBS-R(steel Climadur coated) ............p. 139 Aerated concrete screw FPS-E(A4 stainless steel) ................. p. 140
Tools and accessories .........p. 139
SDF facade anchor............................................. p. 144SDP facade anchor .............. p. 154Aanchor bolt S-KA ............... p. 160
Anchor bolt S-KAH .............. p. 161Nail anchor ND-K................. p. 162Insulation support anchor .. p. 163Chemical anchors ............... p. 165
Cavity wall repair anchor VSD ...................................... p. 168
JA3-SB Solar Fastening System ..............................................p. 107JZ3-SB Solar Fastening System..............................................p. 107
Nibbler ................................. p. 170Riveting tools ...................... p. 172Flat roof installation tool ..... p. 173Electric screw gun .............. p. 177
Cordless screwgun ............. p. 178Special screwgun ............... p. 180Drill bits ............................... p. 182Bits ...................................... p. 186
FR-tool / FR-variotool ......... p. 187 Sockets / Bit holder ............ p. 188Blow-out pump .................. p. 190VACUtest manual pump ...... p. 190
Sealing washer E / ES ......... p. 191Mushromm washer ............ p. 191Shearing load washer VS .... p. 192Thread protection sleeve .... p. 192
Push-on cap ........................ p. 193Spacer AS ............................ p. 194
Storm washers
Special screws
Rivets
Direct Fastening
Scaffolding fasteners
Pipe � ashings
Flat roo� ng Self-drilling screws Dabo®
Stress plates / � at roo� ng anchors
Concrete / aerated concrete screws
Anchors and Embedment Technology
Fastening Systems for Solar Installations
Installation tools
Accessories
Contact / IndexInternational contact ......... p. 196 Index................................... p. 198
N e w E J O T p r o d u c t s
4
EJOT – Your strong partner for fastening solutions in the building industry
Expertise and experience With over 30 years of experience and development know-how “Made in Germany“, we are familiar with all the needs concerning fastening tasks on building envelopes. This expertise is the source for our products and problem solutions which offer real bene� ts to our customers.
Quality and ef� cient assemblyThe quality of our products surpasses planning laws and legal requirements. Our aim is to ensure quick and easy assembly.
Customer-friendly serviceWe make a point of building friendly and trustful relationships with our customers. Our technical consultants offer 24-hour customer service. If required our employees go directly to the building site. We also share our know-how in training seminars.
There for you worldwideOur Europe-wide sales and service network of subsidiaries as well as a worldwide project support team is glad to help our customers at any time.
N e w E J O T p r o d u c t s
5
EJOT Building Fasteners:Over 30 years of building envelope expertise
1. Industrial Lightweight Construction (ILB)High-quality fasteners for � xing pro� led sheets and sandwich panels in the industrial light weight construction
2. External Thermal Insulation Composite Systems (ETICS) Special anchors for � xing insulation on external wall systems.
3. Rear Ventilated Facades (VHF) Fasteners and anchors for � xing substructures and facade fascias of rear ventilated systems
4. Flat Roo� ng (FLD) Fasteners, and installation tools for the ef� cient attachment of insulation and waterproo� ng membrane to � at roofs and slightly sloping roofs.
5. Industrial Window and Facade Technology (IFF)High quality fasteners for the window and door production and the use in aluminium/glass facade systems.
6. Fastening Systems for Solar Installations (BSA) For fastening of mounting systems for thermal solar and photovoltaic installations.
1
3
5
4
2
6
ILB WDVS
VHF FLD
IFF BSA
6
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
ROOFSingle-shell pro� le roof
page 16
ROOFDouble-leaf roof with seam or clamping pro� les
page 22
ROOFFlat roof with waterproof membrane (uninsulated or insulated)
page 26
ROOFTin tile roof
page 18
ROOFRoof with sandwich panels
page 24
ROOFDouble-leaf pro� le roof
page 20
7
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
WALLSingle leaf pro� led wall
page 28
WALLWall with sandwich panels
page 32
GLASS FACADEPost and rail structure
page 99
SOLARFastening Systems for Solar Installations
page 105
WALLRear ventilated facades
page 34
WALLPro� led wall with cassette structure
page 30
8
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eI n f o r m a t i o n
General
PRODUCT RECOMMENDATIONFor the product recommendations it is assumed that the objects are buildings with no excessive demands to corrosion, load-carrying capacity or visual appearance, e.g. warehouses, of� ce buildings, sales rooms etc.The recommendation does not apply to buildings with special demands on the fastening elements due to internal as well as external climatic conditions or which have special demands on the fasteners due to the location of the building.
Structural-physical measures such as the application of vapour barrier sheeting or the insertion of seal strip are not addressed and they need to be considered separately.The application compass is only a suggestion without any claim to accuracy or completeness.
SCREW LENGTHFor determination of the minimum screw length it has to be distinguished between self-drilling screws and non self-drilling screws.
For self-drilling screws the clamp thickness has to be observed. The clamp thickness of a self-drilling screw can be obtained from the product catalogue and is not part of the approval.
For self-tapping fasteners without drill point the cylindrical part of the screw has to be fastened at least 6 mm into the load-bearing component. In practice 20 mm are added to the sum of the thickness of all components that are fastened onto the substructure. The result is the minimum screw length of a self-tapping screw under consideration of sealing washer and assembly unevenness.
SELF-DRILLING SCREWa + 6 mm � clamp thickness (according to information in the product section)
SELF-TAPPING SCREWL = a + 20 mm
DRILLING PERFORMANCEDrilling performance t = component t
I + component t
II
tII
tI
t
a
DEFINITION1 = drill point2 = thread intake3 = full thread4 = free spin zone5 = fastener head
12
34
5
Clamp thickness
a
9
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eI n f o r m a t i o n
Volume determination
GENERALSpacing and position of the fastening elements can be obtained from the static analysis. To determine the exact number of screws is very tedious and time consuming though.A rough estimate of the required quantity is often very helpful for ordering or calculating. There are empirical values, that are expedient if an installation company always works in a similar way and orders the respective amount of fasteners. If the type of construction signi� cantly varies it becomes rather dif� cult. For a rough estimate the following approach has proven to be helpful.
3,5 m
1,5 m
7 m
TRP 35/207/0,75 mm
12 m
Calculation example:Hall 12 x 7 mRoo� ng: Trapezoidal pro� le single-shell on timber purlins
ROOF AND WALL MADE OF METAL PROFILE SHEETS / SANDWICH PANELThe following parameters are known: • Purlin spacing or post and rail spacing• The bar width of the trapezoidal profile
a) Number of screws:
b) Number of side lap screws:
N1 =Roof or wall area [m2] · 1,2
Purlin spacing [m] · 2 · bar width [m]
N2 = Roof or wall area respectively [m2] · 2,2 + (building length [m] + builidng width [m]) · 6
FLAT ROOFINGIn particular for larger building projects the roo� ng membrane and fastener manufacturers offer the service of initial sizing with determination of the needed volume. The result of this initial sizing idepends directly on the quality of the supplied data.
It is recommended to request a questionnaire that contains the most important information for the determination of the screw quantity.
For a rough estimate it can be assumed that an average of 4 screws per m² � at roof are needed.
Estimated demand:
N1 =7 m · 12 m · 1,2
= 162 self-drilling screws JT3-2-6,5x100-E16 + ORKAN storm washer1,5 m · 2 · 0,207 m
N2 = 7 m · 12 m · 2,2 + (12 m + 7 m) · 6 = 300 St. side lap screws JF3-2H-4,8x19-E16
10
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eI n f o r m a t i o n
Order descriptionOptional order description
Example J T 3 - FR - 2 H - 4.8 x 19 - E 11 - 9006
EJOT
Screw type
Self-drilling screw T
Side lap screw EJOFAST® F
Self-tapping screw coarse thread with point
A
Self-tapping screw � ne pitch thread with dog point
Z
Self-tapping screw � ne pitch thread with point
B
Self-drilling screw material
Case-hardened steel, zinc-plated 2
A2 stainless steel with hardened steel drill point
3
A2 stainless steel 4
Self-tapping screw material
Edelstahl A5 (1.4529) / Corremaks® 1
Zinc-plated steel 2
A2 stainless steel 3
A2 stainless steel / CRONIMAKS® 7
Version
Standard (hexagon)
Truss head FR
TORX® drive T
Distance D
Special head geometry X
Countersunk head with TORX® ST
Countersunk � ange head with TORX® STS
Flat head with TORX® ZT
Countersunk head S
Pan head with TORX® LT
Fibre cement FZ
max. drillable metal thickness (in mm)
Free spin zone under screw head H
Screw diameter (in mm)
Screw length (in mm)
Sealing washer material
Zinc-plated steel V
A2 stainless steel E
Aluminium A
Sealing washer diameter (in mm)
Colour (4-digit RAL number) RAL
EJOT® product key:for self-drilling and self-tapping screws
This is how you apply the product key on the example of a
EJOT® self-drilling screwJT3-FR-2H-4,8x19
• with E11 sealing washer• colour version RAL 9006
11
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eI n f o r m a t i o n
Images
SCREW TYPE
VERSION
Self-drilling screw JT
Coarse thread with point(JA)
Fine pitch thread with dog point (JZ)
New screw point geometry (JF)
Truss head(FR)
TORX® drive(T)
Distance(D)
Standard hexagon head
Hexagon head with TORX® drive
Special head geometry
(X)
Countersunk head with TORX® (ST)
Countersunk � ange head with TORX® (STS)
Flat headwith TORX® (ZT)
Countersunk head(S)
Pan head with TORX® (LT)
Fibre cement(FZ)
TORX® is a registered trademark of Acument Intellectual Properties, LLC, Troy Mich., US.
12
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eI n f o r m a t i o n
Application range SAPHIR
EJOT® SAPHIR SELF-DRILLING SCREW JT2 • made of case-hardened, zinc-plated steel• fastens steel components in one work step
Application range SUPER-SAPHIR
EJOT® SUPER-SAPHIR SELF-DRILLING SCREW JT3 • made of A2 stainless steel with hardened steel drill point• fastens steel or aluminium components in one work step
Screw type Pro� led steel sheet to timber substructureScrewdriver
rotation speed rpm
JT2-2-6,5 1500
10 20 30 40 50 60 70 80 100 120 mm
Thickness of the timber substructure
Screw type Pro� led steel sheet to steel substructureScrewdriver
rotation speed rpm
JT3-2H-4,8 1800JT3-2H-5,5 1800
JT3-3H-4,8 � � 1500
JT3-3-5,5 � � 1500
JT3-6-5,5 � � 1300
JT3-6-6,3 � � 1300
JT3-12-5,5 � � 1300
1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 10.0 12.0 mm
Drilling capacity � tI +
tII
Screw type Pro� led aluminium and steel sheet to timber substructureScrewdriver
rotation speed rpm
JT3-2-4,9 1500JT3-2-5,6 1500JT3-2-6,5 1500
10 20 30 40 50 60 70 80 mmThickness of the timber substructure
� max tII
� min tII
recommended application range � tI + t
II
� max tII
� min tII
recommended application range � tI + t
II
Screw type Pro� led steel sheet to steel substructureScrewdriver
rotation speed rpm
JT2-2-4,2 1800JT2-2H-4,8 1800
JT2-3-4,8 � 1800
JT2-3H-5,5 � � 1500
JT2-3-5,5 � � 1500
JT2-6-5,5 � � 1500
JT2-8-5,5 � � 1500
JT2-12-5,5 � � 1500
JT2-6-6,3 � � 1500
JT2-12-6,3 � � 1500
1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 10.0
Drilling capacity � tI + t
II
12.0 mm
13
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eI n f o r m a t i o n
Screw type Pro� led aluminium sheet to timber substructureScrewdriver
rotation speed rpm
JT4-2-4,9 1500
10 20 30 40 50 60 70 80 mm
Thickness of the timber substructure
Screw type Pro� led aluminium sheet to aluminium substructureScrewdriver
rotation speed rpm
JT4-3-4,2 � � 1800
JT4-2-4,8 1800JT4-2H-4,8 1800
JT4-4-4,8 � � 1500
JT4-4-5,5 � � 1500
JT4-6-5,5 � � 1500
1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 mm
Drilling capacity � tI +
tII
Application range Stainless steel SAPHIR
EJOT® STAINLESS STEEL SAPHIR SELF-DRILLING SCREW JT4 • made of A2 stainless steel• connects profiled aluminium sheet components or
aluminium profiles in one work step
Sealing washer correct installation
INSTALLATION OF SEALING WASHERSScrews with sealing washers must be installed using depth control. Deformation of the sealing washer (washer with elastomer seal) is prevented with the aid of the adjustable depth control on the screwdriver.
The sealing washers may not be deformed or the elastomer seal may not be damaged during fastening.
� max tII
� min tII
recommended application range � tI + t
II
to slight
correct
to tight
sloping
14
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eI n f o r m a t i o n
General building authorities approval
Algemeine bauaufsichtliche Zulassungen ('national technical approvals') are granted for such construction products and types of construction for which there are no generally acknowledged rules of technology, DIN standards in particular, or which deviate considerably from these.
National technical approvals are granted by the Deutsche Institut für Bautechnik (DIBt) for all federal states. They are reliable veri� cations of applicability of construction products and veri� cations of applicability of types of construction relating to requirements of construction works in the � eld of construction engineering.
Z-14.1-4Fasteners for structures with "cold pro� les" made of sheet steel - in particular pro� led steel panels
Z-14.1-537Mechanical fasteners for � xing aluminium components together, or with aluminium, steel, timber substructures
Z-14.4-407 Fasteners for sandwich element structures
Z-14.4-426
Self-drilling screws for � xing aluminium clips for building authorities approved standing seam sheets, linear timber components with a min. thickness of 40 mm and other metal part to substructuresmade of steel, aluminium or wood-based materials
Z-14.4-532 Solar Fastening System for � xing solar installations
Z-21.3-1815 Z-21.3-1816
Composite anchor systems for embedment in masonry
Z-21.2-589EJOT facade anchor SDF with accompanying special screws for � xing façade fascia
Z-21.2-967EJOT aerated concrete anchor SDP with accompanying special screws for � xing façade fascia
Z-21.2-1598MKT anchor bolt B for embedment in cracked concrete and light ceiling cladding and suspended ceilings
Z-21.8-1265KERI conical anchor – Special anchor made of stainless steel for the fastening of additional in a permanent manner of external weather resistant skins of three-layerexternal wall panels made of concrete
Z-21.2-1652EJOT VSD – cavity wall repair anchor for subsequent installationof outer leafs
Z-31.1-144Fibre cement corrugated pro� le 177/51 P5 and P6 with polypropylene strip insert (Eternit)
GENERAL BUILDING AUTHORITIES APPROVAL
P-043606Self-drilling screws for � xing aluminium wall brackets to aluminium bearing pro� le substructures for rear-ventilated facade cladding
P-013604Self-drilling screws for � xing wooden slats to aluminium bearing pro� le substructures for rear-ventilated facade cladding
P-043607-02 Fixing aluminium structures to rear-ventilated facade cladding
P-043607-01 Fixing aluminium trapezoidal pro� les to aluminium substructures
P-BWU02-064191Self-drilling screws for � xing wooden slats to aluminium bearing pro� le substructures for regulated rear-ventilated facade cladding according to DIN 18516-1
P-BWU02-046192Self-drilling screws for � xing aluminium wall brackets to aluminium bearing pro� le substructures for rear-ventilated facade cladding
P-BWU02-118016Self-drilling screws for � xing aluminium wall brackets to aluminium bearing pro� le substructures for rear-ventilated facade cladding
GENERAL BUILDING AUTHORITIES APPROVALSGeneral building authorities approvals
A general building authorities test certi� cate is a proof of usability granted for
• construction products which do not neccessitate the compliance with significant requirements to the safety of structural components or
• for components that can be evaluated according to general approved test methods (§ 19 Abs. 1 Musterbauordnung).
The building code A part 1, part 2 and part 3 lists for which product a general building authorities test certi� cate can be granted.Only inspection authorities approved by the DIBt or another building authority are able to grant general building authorities test certi� cates.
15
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eI n f o r m a t i o n
European Technical Approval
The European technical approval is a proof for the � tness for use of a construction product within the meaning of the Construction Products Directive; transposed in Germany by the Bauproduktengesetz (‘Construction Products Law’). The ETA is based on tests, examinations and a technical assessment by approval bodies designated by the EU Member States for this purpose. It covers all product characteristics which can be important for the ful� llment of the legal requirements in the Member States, with the relevant levels of performance required being different in each Member State.
A European technical approval can be granted for construc-tion products for which harmonised speci� cations according to the Construction Products Directive do not (yet) exist or which deviate substantially from a harmonized standard. Basis for the assessment of the � tness for use are either Guidelines for European Technical Approvals ( ETAGs) prepared by EOTA for the relevant product area, or criteria for assessment procedures�that are agreed on with other EOTA bodies for issue of an approval of a speci� c request. In the interests of the manufacturer the veri� cations presented to DIBt will be used as far as possible for the European procedure.
The European technical approval enables the manufacturer to place the CE marking on the construction product and thus the access to the European market. With the CE marking the manufacturer con� rms that he carried out the prescribed veri� cation method and that the conformity of the product is given with the approval.
ETA-07/0013 Fastening elements for roo� ng membrane systems
ETA-06/0067 ETA-06/0068 ETA-06/0069
Composite anchor systems for embedment in masonry
ETA-01/0013 ETA-05/0018
MKT anchor bolt B for embedment in cracked concrete and light ceiling cladding and suspended ceilings
ETA-03/0017 ETA-99/0010 ETA-04/0069
MKT anchor bolt BZ plus for embedment in cracked and non-cracked concrete
ETA-99/0007EJOT special anchor WSS – Special anchor made of stainless steel for the fastening of additional in a permanent manner of external weather resistant skins of three-layerexternal wall panels made of concrete
ETA-10/0200 Fasteners for metal components and sheet metal
ETA-10/0305EJOT SDF-10V and SDF-10H plastic anchor for multiple fastening of non-load-bearing systems in concrete and masonry
EUROPEAN TECHNICAL APPROVAL
16
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Single-shell pro� le roof
DESCRIPTIONSingle-shell uninsulated pro� le roof, purlin design.The roof cladding is directly fastened to the purlins and it is weather exposed.
APPLICATION• Roof overhangs• Sheds• Carports
CROSS REFERENCEStorm washers ........................................ page 85
Pro� led sheet to substructure
Substructure (component II)
Steel purlin1,5 – 5,0 mm
Steel purlin4,0 – 12,0 mm
Steel purlin� 10,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fastening to crown(trapezoidal pro� le)
Self-drilling screwJT3-6-5,5xL-E16
page 60
+ ORKAN storm washer
Self-drilling screwJT3-12-5,5xL-E16
page 62
+ ORKAN storm washer
Self-tapping screw JZ3-6,3xL-E16
page 80
+ Storm washer pre-drilling Ø 5,7 mm
Self-tapping screw JZ3-6,3xL-E16
page 80
+ Storm washer
Self-tapping screw JA3-6,5xL-E16
page 78
+ Storm washerpre-drilling Ø 4,5 mm
Self-drilling screwJT3-2-6,5xL-E16
page 58
+ ORKAN storm washer
Fastening to crown(corrugated pro� le)
Self-drilling screwJT3-6-5,5xL-E16
page 60
+ ORKAN storm washer
Self-drilling screwJT3-12-5,5xL-E16
page 62
+ ORKAN storm washer
Self-tapping screw JZ3-6,3xL-E16
page 80
+ Storm washerpre-drilling Ø 5,7 mm
Self-tapping screw JZ3-6,3xL-E16
page 80
+ ORKAN storm washer
Self-tapping screw JA3-6,5xL-E16
page 78
+ Storm washer pre-drilling Ø 4,5 mm
Self-drilling screwJT3-2-6,5xL-E16
page 58
+ ORKAN storm washer
Fastening to valley(only trapezoidal pro� le)
Self-drilling screwJT3-6-5,5x25-E22
page 60
Self-drilling screwJT3-12-5,5x40-E22
page 62
Self-tapping screw JZ3-6,3x19-E22
page 80
pre-drilling Ø 5,7 mm
Self-drilling screwJT3-6-5,5x25-E22
page 60
Self-tapping screw JA3-6,5x50-E22
page 78
pre-drilling Ø 4,5 mm
Self-drilling screwJT3-2-6,5x50-E22
page 58
Fastening to crown(� bre cement sheet)
Self-drilling screwJT2-FZ-6-6,3
page 49
Self-drilling screwJT2-FZ-12-6,3
page 50
Self-drilling screwJT2-FZ-F-6,5
page 51
Self-drilling screwJT4-FZ-6,5
page 72
For highly corrosive environments we recommend the use of Corremaks® self-tapping screws ............... page 82
17
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
SIDE LAP STITCHING If side lap stitching is not regulated any differently, it has to be spaced 50 - 666 mm apart, according to DIN 18807-3. A screw spacing of 500 mm has proven to be very practical.In order to prevent stripping of the pro� led sheets and destruction of the sealing washers the use of screws with a free spin zone is recommended.
DETERMINATION OF THE SCREW LENGTH Special attention should be paid to the waterproo� ng of fastening elements. Practical experience has proventhat leakage of only a few tenth millimetres can lead to considerable damage. For that reason EJOT recommends crown � xing with storm washers. The advantage of a storm washer is safety against rain water penetration in addition to the effect that indentation of the crown can be largely prevented.
For trapezoidal pro� le joints the installation depth into timber is regulated by the respective approval. The minimum installa-tion depth of a 6,5 screw is 26 mm and the maximum installation depth is 78 mm. In practical experience an installation depth of 50 mm into timber has proven to be optimal, since the pullover load of a 0,75 mm thick steel trapezoidal pro� le shows approximately the same load bearing capacity against pulling-out of a timber purlin with 50mm installation depth as a 6,5 screw.
Pre-drilling may be omitted if a self-drilling screw is used. Pre-drilling of timber has the advantage that expansion forces, which can lead to splicing of the wood, can be clearly reduced and for that reason a reduction of the edge distance is made possible through pre-drilling.
DETERMINATION OF THE SCREW LENGTH h = Height of the trapezoidal or corrugated pro� leL = screw length
Pro� led sheet to steel substructure
Pro� led sheet to insertion rail
Pro� led sheet totimber substructure
1,5 – 5,0 mm 4,0 – 12,0 mm � 10,0 mm 3.0 mm Min. width 65 mm
JT3-6-5,5xL-E16+ ORKAN storm washer
JT3-12-5,5xL-E16+ ORKAN storm washer
JZ3-6,3xL-E16+ ORKAN storm washer
JZ3-6,3xL-E16+ ORKAN storm washer
JA3-6,5xL-E16+ ORKAN storm washer
JT3-2-6,5xL-E16+ ORKAN storm washer
h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm]
0 – 30 50 25 – 33 50 35 90
3 – 44 64 39 – 47 64 40 100 20 – 40 100
18 – 44 70 19 – 43 78 19 – 60 80 55 – 63 80 40 – 60 115 40 – 60 120
38 – 64 90 39 – 63 98 29 – 70 90 65 – 73 90 45 – 70 125 60 – 80 140
58 – 84 110 59 – 83 118 39 – 80 100 75 – 83 100 70 – 95 150 80 – 100 160
78 – 104 130 79 – 103 138 54 – 95 115 90 – 98 115 95 – 120 175 100 – 120 180
98 – 124 150 99 – 123 158 64 – 105 125 100 – 108 125 120 – 145 200 120 – 140 200
118 – 144 170 119 – 143 178 74 – 115 135 110 – 118 135 150 – 175 230
138 – 164 190 139 – 163 198 89 – 130 150 125 – 133 150
114 – 155 175 150 – 158 175
139 - 180 200 175 – 183 200
Side lap stitching
Trapezoidal pro� le Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Side lap screwJF3-2H-4,8x19-E14
page 53
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
Corrugated pro� le Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Self-drilling screwJT3-FR-2H-Plus-5,5x25-E11
page 56
18
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Tin roof tile
DESCRIPTIONSingle-shell uninsulated pro� le roof, purlin design.The roo� ng is fastened to wooden slats and weather exposed.
APPLICATION• Roof overhangs• Sheds• Carports
Roo� ng sheet onsubstructure
Substructure (component II)
Wooden slats
Screw material:
Steelcase-hardened,
zinc-plated
Self-drilling screwJT2-2-4,9xL-V14
page 40
Screw material:
A2 stainless steel with hardened steel drill
point
Self-drilling screwJT3-2-4,9xL-E14
page 54
Side lap stitching
Trapezoidal pro� le Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Side lap screwJF3-2H-4,8x19-E14
page 53
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
Corrugated pro� le Self-drilling screwJT3-2H-Plus-5,5x25-E11
page 55
Self-drilling screwJT3-FR-2H-Plus-5,5x25-E11
page 56
19
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eN o t e s
© Dolce Hotel DOLCE HOTEL, UNTERSCHLEISSHEIM, GERMANYSupplied by EJOT: EJOT® ETICS anchor
20
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Double-leaf pro� led roof
DESCRIPTIONThe load-bearing shell is fastened inside to the steel or timber purlins. The external roof shell is kept away through thin-walled spacers. The external roof shell serves for weather protection, the internal load-bearing shell for load bearing.
APPLICATION• Heated buildings of all kind and scope
CROSS REFERENCEStorm washers ........................................ page 85
Load-bearing shell to substructure
Substructure (component II)
Steel purlin� 1,5 mm
Steel purlin� 6,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fastening to valley Self-tapping screwJZ3-6,3x19-E16
page 80
Tie pinHSBR-14
page 111
Self-drilling screwJT2-6-6,3x22-V16
page 44
Self-drilling screwJT3-2-6,5x65-E16
page 58
Side lap stitching load-bearing shell
Load-bearing shell Self-drilling screwJT2-2H-4,8x19
page 39
Self-drilling screwJF2-2H-4,8x19
page 38
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
21
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Spacer to load-bearing shell
Spacer (component I)1,5 – 2,0 mm
Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Spacer (component I)> 1,5 mm
Closed end rivetAl/E-4,8x10
page 103
Pre-drilling Ø 4,9 mm
Roof shell to spacer
Substructure (component II)
Spacer1,5 – 5,0 mm
Fastening to crown(trapezoidal pro� le)
Self-drilling screwJT3-6-5,5xL-E16
page 60
+ ORKAN storm washer
Fastening to valley(only trapezoidal pro� le)
Self-drilling screwJT3-6-5,5x25-E22
page 60
Pro� led sheet to steel substructure
1,5 – 5,0 mm
JT3-6-5,5xL-E16+ ORKAN storm washer
h [mm] L [mm]
18 – 44 70
38 – 64 90
58 – 84 110
78 – 104 130
98 – 124 150
118 – 144 170
138 – 164 190
DETERMINATION OF THE SCREW LENGTH h = Height of the trapezoidal or corrugated pro� leL = Screw lengthSide lap stitching
Roof shell
Roof shell(trapezoidal pro� le)
Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Side lap screwJF3-2H-4,8x19-E14
page 53
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
Roof shell(corrugated pro� le)
Self-drilling screwJT3-2H-Plus-5,5x25-E11
page 55
Self-drilling screwJT3-FR-2H-Plus-5,5x25-E11
page 56
22
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Double-leaf roof with seam or clamping pro� le
DESCRIPTIONThe load-bearing shell is fastened inside to the steel or timber purlins. The clips for � xing standing seam systems are � xed with self-drilling screws either directly to the load-bearing shell or indirectly to an additional spacer. The outer leaf is � xed to the clips with a folding machine.
APPLICATION• Heated buildings of all kind and scope• Arched roofs• Barrel roofs
Load-bearing shell to substructure
Substructure (component II)
Steel purlin� 1,5 mm
Steel purlin� 6,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fastening to valley Self-tapping screwJZ3-6,3x19-E16
page 80
Pre-drilling Ø 5,7 mm
Tie pinHSBR-14
page 111
Self-drilling screwJT2-6-6,3x22-V16
page 44
Self-drilling screwJT3-2-6,5x65-E16
page 58
Side lap stitching load-bearing shell
Load-bearing shell Self-drilling screwJT2-2H-4,8x19
page 39
Self-drilling screwJF2-2H-4,8x19
page 38
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
23
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Clip onsubstructure
Substructure (component II)
Spacer� 1,5 mm
Spacer1,5 – 5,0 mm
Trapezoidal pro� le� 0,75 mm
Roof boarding / OSB
Self-drilling screwJT3-X-2-6,0xL
page 66
Self-drilling screwJT3-6-5,5xL
page 60
Self-drilling screwJT3-X-2-6,0xL
page 66
Self-drilling screwJT3-X-2-6,0xL
page 66
DETERMINATION OF THE SCREW LENGTH h = Clip height incl, Thermo stopL = screw length
Clip onsteel substructure
Clip on roof boarding /OSB
JT3-X-2-6,0xL JT3-6-5,5xL JT3-X-2-6,0xL
h [mm] L [mm] h [mm] L [mm] h [mm] L [mm]
0 – 10 25 5 25 0 – 5 36
0 – 20 36 10 30 0 – 15 46
0 – 30 46 15 35
20 – 30 50
NOTEThe JT3-X-2-6,0xL self-drilling screw is a building authorities approved product to fasten clips to steel, timber or aluminium substructures. Every clip has to be � xed with 2 screws in the order depicted below. The special characteristic of the screw are the grooves under the head. They are able to considerably increase the stripping torque, which leads to an increased assembly reliability.
Position of the fastening elementsPosition 1
Position 2
24
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Roof with sandwich panels
DESCRIPTIONSandwich panels are composite elements. They consist of two metallic layers that are usually connected shear resistant with polyurethane foam. The ratio of weight to load-carrying capacity and the insulating properties are unbeatable. Sandwich panels are fastened directly to the substructure. The following element is pushed to the assembled element from the side and then fastened.
APPLICATION• Heated buildings of all sizes and scope
CROSS REFERENCEStorm washers ........................................ page 85
Sandwich element to substructure
Substructure (component II)
Steel purlin1,5 – 5,0 mm
Steel purlin4,0 – 12,0 mm
Steel purlin� 10,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fastening to crown Self-drilling screwJT3-6-5,5xL-E16
page 60
+ ORKAN storm washer
Self-drilling screwJT3-12-5,5xL-E16
page 62
+ ORKAN storm washer
Self-tapping screw JZ3-6,3xL-E16
page 80
+ Storm washerPre-drilling Ø 5,7 mm
Self-tapping screw JZ3-6,3xL-E16
page 80
+ Storm washerPre-drilling Ø 5,3 mm
Self-drilling screwJT3-2-6,5xL-E16
page 58
+ ORKAN storm washer
25
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Side lap stitching
Trapezoidal pro� le Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Side lap screwJF3-2H-4,8x19-E14
page 53
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
Corrugated pro� le Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Self-drilling screwJT3-FR-2H-Plus-5,5x25-E11
page 56
DETERMINATION OF THE SCREW LENGTH h = height sandwich panelL = screw length
Pro� led sheet to steel substructure
Pro� led sheet to insertion rail
Pro� led sheet totimber substructure
1,5 – 5,0 mm 4,0 – 12,0 mm � 10,0 mm 3.0 mm Min. width 65 mm
JT3-6-5,5xL-E16+ ORKAN storm washer
JT3-12-5,5xL-E16+ ORKAN storm washer
JZ3-6,3xL-E16+ ORKAN storm washer
JZ3-6,3xL-E16+ ORKAN storm washer
JT3-2-6,5xL-E16+ ORKAN storm washer
h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm]
0 – 30 50 25 – 33 50
3 – 44 64 39 – 47 64 20 – 40 100
18 – 44 70 19 – 43 78 19 – 60 80 55 – 63 80 40 – 60 120
38 – 64 90 39 – 63 98 29 – 70 90 65 – 73 90 60 – 80 140
58 – 84 110 59 – 83 118 39 – 80 100 75 – 83 100 80 – 100 160
78 – 104 130 79 – 103 138 54 – 95 115 90 – 98 115 100 – 120 180
98 – 124 150 99 – 123 158 64 – 105 125 100 – 108 125 120 – 140 200
118 – 144 170 119 – 143 178 74 – 115 135 110 – 118 135
138 – 164 190 139 – 163 198 89 – 130 150 125 – 133 150
114 – 155 175 150 – 158 175
139 - 180 200 175 – 183 200
26
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Load-bearing shell to substructure
Substructure (component II)
Steel purlin� 1,5 mm
Steel purlin� 6,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fastening to valley Self-tapping screwJZ3-6,3x19-E16
page 80
Pre-drilling according to the tablepage 26
Tie pinHSBR-14
page 111
Self-drilling screwJT2-6-6,3x22-V16
page 44
Self-drilling screwJT3-2-6,5x65-E16
page 58
NOTECompared to the metal-metal combination, the metal plastic combination has the advantage of minimal thermal transmittance and the telescope effect prevents screw head protrusion due to foot traf� c.
Metall-metal combinations are indispensable for renovations where old bitumen roo� ng membranesare equipped with a new layer of insulation material. A plastic stress plate can only be installed with increased assembly effort in these kind of applications.
For renovations we generally recommend A4 stainless steel screws, since increased corrosion can be expected for wet roof structures.
CLIMADUR• High-grade coating to improve
the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
Flat roof with waterproof membrane
(uninsulated or insulated)
DESCRIPTIONAt � rst the load-bearing shell is fastened to the steel or wooden slats inside. This is followed by the vapour barrier sheeting and (optionally) covered with insulation. The roo� ng membrane serves as weather protection and is usually layed-out overlapping and then fused with hot air. The � xing of the roo� ng membrane (optionally), incl. insulation and vapour barrier sheeting, is carried-out with self-drilling roof screws to the load-bearing shell.
The load-bearing shell is often concrete, planks, timber or similar wood-based material. Other fastening elements might be required.
APPLICATION• Mainly sales and production halls with flat roofs
Side lap stitching load-bearing shell
Load-bearing shell Self-drilling screwJT2-2H-4,8x19
page 39
Self-drilling screwJF2-2H-4,8x19
page 38
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
27
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Waterproo� ng membranes tosubstructureno insulation
Substructure (component II)
Trapezoidal pro� le Roof boarding / OSB Concrete Porous concrete
Insertion depth � 20 mm � 30 mm 30 – 50 mm � 60 mm
Metal-metal-combination
Dabo® screwA/F 8-R-4,8xLpage 128
+ stress plateHTV 82/40 Fpage 135
Dabo® screwA/F 8-R-4,8xLpage 128
+ stress plateHTV 82/40 Fpage 135
Concrete screwFBS-R-6,3xLpage 139
+ stress plateHTV 82/40 Fpage 135
Aerated concrete screw FPS-E-8,0xL
page 140
+ stress plateHTV 82/40 Fpage 135
Waterproo� ng membranes tosubstructure
with insulation
Substructure (component II)
Trapezoidal pro� le Roof boarding / OSB Concrete Porous concrete
Insertion depth � 20 mm � 30 mm 30 – 35 mm � 60 mm
Metal-metal-combination
Dabo® screwA/F 8-RT-4,8xLpage 129
+ stress plateHTV 82/40
page 134
Dabo® screwA/F 8-RT-4,8xLpage 129
+ stress plateHTV 82/40
page 134
Metal-plasticcombination
Dabo® screwTKR-4,8xL
page 130
+ stress plateHTK 50xL
page 136
Dabo® screwTKR-4,8xL
page 130
+ stress plateHTK 50xL
page 136
Concrete screwFBS-R-6,3xLpage 139
+ stress plateEcoTek 50xLpage 136
Aerated concrete screw FPS-E-8,0xL
page 140
+ stress plateEcoTek 50xLpage 136
28
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Single leaf pro� led wall
DESCRIPTIONThe trapezoidal pro� le is directly fastened to the post or rail and is weather exposed.
APPLICATION• Simple sheds, carports, bicycle sheds
Pro� led sheet to substructure
Substructure (component II)
Steel purlin1,5 – 5,0 mm
Steel purlin4,0 – 12,0 mm
Steel purlin� 10,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fixi
ng to
val
ley
(trap
ezoi
dal p
ro� l
e) Self-drilling screwJT3-6-5,5x25-E16
page 60
Self-drilling screwJT3-12-5,5x40-E16
page 62
Self-tapping screw JZ3-6,3x19-E16
page 80
pre-drilling Ø 5,7 mm
Self-drilling screwJT3-6-5,5x25-E16
page 60
Self-drilling screwJT3-2-6,5x50-E16
page 58
Fixi
ng to
val
ley
(cor
ruga
ted
pro�
le) Self-drilling screw
JT3-FR-6-5,5x25-E11
page 61
Self-drilling screwJT3-FR-12-5,5x40-
E11
page 63
29
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Side lap stitching
Trap
ezoi
dal p
ro� l
e Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Side lap screwJF3-2H-4,8x19-E14
page 53
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
Corr
ugat
ed p
ro� l
e Self-drilling screwJT3-2H-Plus-5,5x25-E11
Page 55
Self-drilling screwJT3-FR-2H-Plus-5,5x25-E11
page 56
30
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Pro� le wall with cassette structure
DESCRIPTIONThe cassette is directly fastened to steel supports. The outer leaf is fastened to the cassette bars and does nt only serve as weather protection but also as bracing for the cassettes. The cassette wall positively servesas noise and � re protection. The insulating properties of a cassette wall are not as good compared toother types of construction.
APPLICATION• Heated buildings• Buildings with a high noise level• Buildings with increased demands on fire protection• Buildings with heat from production processes
Cassette to substructure
Substructure (component II)
Steel purlin4,0 – 12 mm
Steel purlin� 6,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Fixing to valley Self-drilling screwJT2-12-5,5x35-V16
page 45
Tie pinHSBR-14
page 111
Self-drilling screwJT2-6-6,3x19-V16
page 44
Self-drilling screwJT3-2-6,5x65-E16
page 58
Side lap stitchingCassette
Self-drilling screwJT2-2H-4,8x19
page 39
Self-drilling screwJF2-2H-4,8x19
page 38
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
NOTEThe fastening elements may only be mounted a max. of 75 m away from the cassette bars The fastener in the middle of the cassette does not serve the load-transmission but it has only a structural character.
Depending on the cassette type and manufacturer it is not easy to adhere to the 75 mm during the installation and at the same time install the the fastening element perpendicular to the surface.
The closer the vertical seam is positioned to the valley the more effective condensation can be prevented. The corrugation bridges are not a positioning aid for the side lap stitching of cassettes.
31
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Pro� led sheet to substructure
Substructure (component II)
2 x 0,63 mm – 2 x 1,25 mm
2 x 1,5 mm
Fixi
ng to
val
ley
(trap
ezoi
dal p
ro� l
e) Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Self-drilling screwJT3-6-5,5x25-E16
page 60
Fixi
ng to
val
ley
(cor
ruga
ted
pro�
le) Self-drilling screw
JT3-FR-2H-Plus-5,5x25-E11
page 56
Self-drilling screwJT3-FR-6-5,5x25-E11
page 61
NOTEThe approval for the fasteners suitable for cassette wall structures includes a connection where component II consists of two overlapping pro� led sheets, which leads to an improved load-carrying capacity.
Side lap stitching
Trap
ezoi
dal p
ro� l
e Self-drilling screwJT3-2H-Plus-5,5x25-E16
page 55
Side lap screwJF3-2H-4,8x19-E14
page 53
Drilling capacity tI + t
II
� (0,88 + 0,88) mm
Corr
ugat
ed p
ro� l
e Self-drilling screwJT3-2H-Plus-5,5x25-E11
page 55
Self-drilling screwJT3-FR-2H-Plus-5,5x25-E11
page 56
32
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Wall with sandwich panels
DESCRIPTIONSandwich panels are composite elements. They consist of two metallic layers that are usually connected shear resistant with polyurethane foam. The ratio of weight to load-carrying capacity is unbeatbale. Sandwich panels are fastened directly to the substructure. The following element is pushed to the assembled element from the side and then fastened.
APPLICATION:• Heated buildings of all sizes and scope
Sandwich element to substructure
Substructure (component II)
Steel purlin1,5 – 5,0 mm
Steel purlin4,0 – 12,0 mm
Steel purlin� 10,0 mm
Insertion rail 3,0 mm
Timber purlinMin. width 65 mm
Self-drilling screwJT3-D-6H-5,5/6,3xL
-E19
page 64
Self-drilling screwJT3-D-12H-5,5/6,3xL
-E19
page 65
Self-tapping screw JZ3-6,3xL-E19
page 80
pre-drilling Ø 5,7 mm
Self-tapping screw JZ3-6,3xL-E19
page 80
pre-drilling Ø 5,3 mm
Self-drilling screwJT3-2-6,5xL-E16
page 58
33
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
DETERMINATION OF THE SCREW LENGTH h = height sandwich panelL = screw length
Sandwich element to steel substructure
Sandwich elements to insertion rail
Sandwich element totimber substructure
1,5 – 5,0 mm 4,0 – 12,0 mm � 10,0 mm 3.0 mm Min. width 65 mm
JT3-D-6H-5,5/6,3xL-E19
JT3-D-12H-5,5/6,3xL-E19
JZ3-6,3xL-E19 JZ3-6,3xL-E19 JT3-2-6,5xL-E19
h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm] h [mm] L [mm]
0 – 30 50 25 – 33 50 20 – 40 100
35 – 40 67 36 – 40 75 3 – 44 64 39 – 47 64 40 – 60 120
48 – 60 87 48 – 60 95 19 – 60 80 55 – 63 80 60 – 80 140
58 – 80 107 58 – 80 115 29 – 70 90 65 – 73 90 80 – 100 160
72 – 100 127 72 – 100 135 39 – 80 100 75 – 83 100 100 – 120 180
92 – 120 147 92 – 120 155 54 – 95 115 90 – 98 115 120 - 140 200
112 – 140 167 110 – 140 175 64 – 105 125 100 – 108 125
140 – 170 197 130 – 160 195 74 – 115 135 110 – 118 135
170 – 210 237 170 – 210 245 89 – 130 150 125 – 133 150
114 – 155 175 150 – 158 175
139 – 180 200 175 – 183 200
NOTEPractical experience has shown that visibly installed sandwich panels always show a slight indentation at the fastening point. When using screws with high thread (JT3-D) indentations can be reduced but not completely prevented.
Fig. 1Not visible sandwich panel installation
Fig. 2Visible sandwich panel installation
34
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eA p p l i c a t i o n a d v i c e
Rear ventilated facades
DESCRIPTIONRear ventilated facades are characterised by insulation and cladding of the system being structurally separated. The rear ventilated area regulates the moisture equilibrium of the building. A substructure, which is � xed to the solid substrate with anchors, serves as distancing assembly of the cladding and this way a rear ventilated area between insulation and outer layer is created.
APPLICATIONCladding of a rear ventilated facade• Plaster-base sheeting • Tile• Resin composite panels
ADVANTAGES:The construction possibilities and the structural-physical properties are the reason for the attractiveness of a rear ventilated facade
EJOT is a member of the "Fachverband Baustoffe und Bauteile für vorgehängte hinterlüftete Fassaden e.V." (professional association building material and components for rear ventilated facade)
EmbedmentSubstructure on
substrate
Embedment substrate
Concrete Solid brickHollow or
perforated brickPorous concrete
Timber substructure Façade anchorSDF-S-10VxL
page 144
Façade anchorSDF-S-10VxL
page 144
Façade anchorSDF-S-10HxL
page 146
Façade anchorSDP-S-10SxL
page 154
Metal substructureFaçade anchor
SDF-KB-10Vx50
page 145
Façade anchorSDF-KB-10Vx60
page 145
Façade anchorSDF-KB-10Hx80
page 147
Façade anchorSDP-KB-10Sx80
page 155
35
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e r v i c eA p p l i c a t i o n a d v i c e
Fastening the substructure
Aluminium / aluminium Self-drilling screwJT4-3H/5-5,5x19
page 69
Timber / aluminium Self-drilling screwJT4-S-2-4,8xL
page 73
Fixing insulating material
Soft insulating material Insulation support anchorDH
page 163
Metal insulation support anchor
DMH
page 164
+ metal insulation stress plate
DMT
Hard insulating material Metal insulation support anchorDMH
page 164
Fixing facade fascia
Plaster-base sheeting Self-drilling screwJT4-STS-3-4,8
page 73
Wood cladding Chipboard screwSH3-S
page 98
NOTEBearing pro� les and wall brackets of rear ventilated facades are often made of aluminium. In order to prevent restraints in the design, the wall brackets are equipped with slotted and round holes. To keep the joint in the slotted hole � exible even after installation of the screw, the EJOT® self-drilling screw JT4-3H/5-5,5x19 is used.A thread-free area under the screw head sits in the slotted hole of the wall bracket after the installation. The bearing pro� le (component II) is prevented by a free spin zone in front of the thread-free area from force-locking the components.
The application area of this screw is limited to a 3,0 mm thick wall bracket and a 1,6 mm to 2,0 mm thick bearing pro� le.
36
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e r v i c eN o t e s
© Ideetainment GmbH & Co. KG WALE INDOOR PLAYGROUND, FRIEDRICHSKOOG, GERMANYSupplied by EJOT: EJOT Dabo® screw A/F8
37
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
EJOT®
Self-drilling screws
SAPHIRJT2
SUPER-SAPHIRJT3
Stainless steel SAPHIR JT4
FastenerMaterial
Case-hardened steel,zinc-plated
A2 stainless steel with hardened drill point
A2 stainless steel
For components made of
steel steel or aluminium aluminium
max. drillingcapacity mm
12 12 6
PRODUCT VERSIONS
EJOT®
Self-drilling screws
EJOFAST®
Side lap screw JF2EJOFAST®
Side lap screw JF3
FastenerMaterial
Case-hardened steel,zinc-plated
A2 stainless steel with hardened drill point
For components made of
steel steel or aluminium
max. drillingcapacity mm
0.88 + 0.88 0.88 + 0.88
PRODUCT VERSIONS
EJOT® SAPHIRSelf-drilling screws
ADVANTAGES:• Connects components in one step• Drilling, thread-forming and fastening• Decrease assembly times• Save tool changes and costs for drills• Available with captive sealing washer upon request
FEATURES• Hexagon or hexalobular drive / TORX®
• Free Spin Zone under the head facilitates side lap stitching
• Small dead centre prevents misalignment on the component surface
• Zinc-plated sealing washer made of steel or stainless steel with vulcanised elastomer. Excellent atmospheric - and UV-resistance.
CLIMADUR• High-grade coating to improve
the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
CROSS REFERENCEApplication advice ................................... page 6 Information ............................................. page 8
Description and selection of the self-drilling screw
DRILLING PERFORMANCEDrilling performance t = component t
I + component t
II
SELF-DRILLING SCREWa + 6 mm � Clamp thickness (according to information in the product part)
tII
tI
t
Clamp thickness
a
38
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer4.2 16 0 - 9 1,000 JT2-2-4,2x16 3591100624
EJOT® SAPHIR Self-drilling screw JT2-2-4,2
J2
APPLICATION RANGE• Side lap stitching of profiled steel sheetsFEATURES• Case-hardened steel, zinc-plated
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 1,0 mm
Drive ........................................................... hexagont A/F7
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
EJOFAST® Side lap screw JF2-2H-4,8
J2
APPLICATION RANGE• Side lap stitching of pro� led steel sheets
FEATURES• Steel, case-hardened, zinc-plated
with innovative screw point geometry• With free spin zone under the screw head for side lap
stitching• Non-skid application• Fastening without swarf
APPROVALETA pending
TECHNICAL DATADrilling capacity t
I + t
II ............................... 0,88 + 0,88 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ø in mm
Length mm
Clamp thickness
in mmPU
Price € / 100
pcs.Order description Part Number
without sealing washer4.8 19 0 - 9 1,000 JF2-2H-4,8x19 7380628601
39
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIR Self-drilling screw JT2-2H-4,8
J2
APPLICATION RANGE• Side lap stitching of profiled steel sheets
FEATURES• Case-hardened steel, zinc-plated• With free spin zone under the screw head for side lap
stitching
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer4.8 19 0 - 9 1,000 JT2-2H-4,8x19 3592200644
RAL 9006 RAL 9002 RAL 8012 RAL 7016 RAL 6020 RAL 5010 white aluminium grey white red brown anthracite chrome oxide green gentian blue
EJOT® SAPHIRSelf-drilling screw JT2-2H/3-4,8
J2
APPLICATION RANGE• Side lap stitching of pro� led steel sheets
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer• With free spin zone under the screw head for side lap
stitching
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness
mmPU
Price €/100 pcs.
Order description Part number
Sealing washer V14, Ø 14 mm4.8 20 0 - 6 1,000 JT2-2H/3-4,8x20-V14 3592251644Sealing washer V14, Ø 14 mm, coloured4.8 20 0 - 6 1,000 JT2-2H/3-4,8x20-V14* -
* add four-digit RAL colour code.
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesOther RAL colours and special colours on request
40
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer (no approval)5.5 22 0 - 10 1,000 JT2-2H-5,5x22 3593300644Sealing washer V16, Ø 16 mm5.5 22 0 - 7 500 JT2-2H-5,5x22-V16 3593321644
EJOT® SAPHIRSelf-drilling screw JT2-2H-5,5
J2
APPLICATION RANGE• Side lap stitching of profiled steel sheets• Fastening of pro� led steel sheets
onto 0.63 – 1.5 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer• With free spin zone under the screw head for side lap
stitching
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
Sealing washer V14, Ø 14 mm, coloured4.9 35 500 JT2-2-4,9x35-V14* -
* add four-digit RAL colour code.
EJOT® SAPHIRSelf-drilling screw JT2-2-4,9
J2
APPLICATION RANGE• Fastening of profiled steel sheets onto
timber substructure • Fastening of roofing sheets onto
timber substructure
FEATURES• Case-hardened steel, zinc-plated, powder-coated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer• Thread according to DIN 7998
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesOther RAL colours and special colours on request
41
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIRSelf-drilling screw JT2-2H-6,3
J2
APPLICATION RANGE• Side lap stitching of pro� led steel sheets
FEATURES• Case-hardened steel, zinc-plated• With free spin zone under the screw head for side lap
stitching
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.3 22 0 - 8 500 JT2-2H-6,3x22 7380188601
6.3 32 0 - 18 500 JT2-2H-6,3x32 7380452601
EJOT® SAPHIRSelf-drilling screw JT2-2-6,5
J2
APPLICATION RANGE• Fastening of profiled steel sheets onto
timber substructure
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
TECHNICAL DATADrilling capacity t
I + t
II ............................................ 2,0 mm
Drive ........................................................hexagon A/F3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.5 35 500 JT2-2-6,5x35 35946006246.5 50 250 JT2-2-6,5x50 35948006246.5 65 250 JT2-2-6,5x65 35949006246.5 90 200 JT2-2-6,5x90 3594000624
Sealing washer V16, Ø 16 mm6.5 35 500 JT2-2-6,5x35-V16 35946216246.5 50 250 JT2-2-6,5x50-V16 35948216246.5 65 250 JT2-2-6,5x65-V16 3594921624
6.5 90 200 JT2-2-6,5x90-V16 3594021624
42
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer5.5 19 0 - 6 1,000 JT2-3-5,5x19 35932006345.5 25 0 - 12 500 JT2-3-5,5x25 3593400634Sealing washer V16, Ø 16 mm5.5 19 0 - 3 500 JT2-3-5,5x19-V16 3593221634
5.5 25 0 - 9 500 JT2-3-5,5x25-V16 3593421634
EJOT® SAPHIRSelf-drilling screw JT2-3-5,5
J2
APPLICATION RANGE• Fastening of pro� led steel sheets
onto 1 – 2.5 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 2,5 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
EJOT® SAPHIRSelf-drilling screw JT2-3-4,8
J2
APPLICATION RANGE• Fastening of profiled steel sheets
onto 2 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,5 + 2,5 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer (no approval)4.8 19 0 - 11 1,000 JT2-3-4,8x19 35922006344.8 25 0 - 17 500 JT2-3-4,8x25 35924006344.8 38 0 - 27 500 JT2-3-4,8x38 3592600634Sealing washer V14, Ø 14 mm4.8 19 0 - 8 1,000 JT2-3-4,8x19-V14 35922516344.8 25 0 - 14 500 JT2-3-4,8x25-V14 3592451634
4.8 38 0 - 24 500 JT2-3-4,8x38-V14 3592651634
43
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIRSelf-drilling screw JT2-3H-5,5
J2
APPLICATION RANGE• Side lap stitching of pro� led steel sheets• Fastening of pro� led steel sheets
onto 1 – 2.5 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,5 + 1,5 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer (no approval)5.5 19 6 1,000 JT2-3H-5,5x19 35982006345.5 25 12 500 JT2-3H-5,5x25 3598400634Sealing washer V16, Ø 16 mm5.5 19 3 500 JT2-3H-5,5x19-V16 3598221634
5.5 25 9 500 JT2-3H-5,5x25-V16 3598421634
EJOT® SAPHIRSelf-drilling screw JT2-3H-6,3
J2
APPLICATION RANGE• Side lap stitching of profiled steel sheets• Fastening of profiled steel sheets onto
1 – 2,5 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• With free spin zone under the screw head for side lap
stitching
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,5 + 1,5 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.3 22 0 - 9 500 JT2-3H-6,3x22 3574300654
6.3 32 0 - 19 500 JT2-3H-6,3x32 3574500654
44
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIR Self-drilling screw JT2-6-6,3
J2
APPLICATION RANGE• Fastening of profiled steel sheets
onto 2 – 5 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,5 + 5,0 mm
Drive ........................................................hexagon A/F3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.3 19 0 - 7 500 JT2-6-6,3x19 35742006346.3 22 0 - 10 500 JT2-6-6,3x22 35743006346.3 25 0 - 13 500 JT2-6-6,3x25 35744006346.3 32 0 - 20 500 JT2-6-6,3x32 35745006346.3 38 0 - 26 500 JT2-6-6,3x38 3574600634Sealing washer V16, Ø 16 mm6.3 19 0 - 4 500 JT2-6-6,3x19-V16 35742216346.3 22 0 - 7 500 JT2-6-6,3x22-V16 35743216346.3 25 0 - 10 500 JT2-6-6,3x25-V16 35744216346.3 32 0 - 17 500 JT2-6-6,3x32-V16 3574521634
6.3 38 0 - 23 500 JT2-6-6,3x38-V16 3574621634
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer5.5 19 0 - 7 1,000 JT2-6-5,5x19 35732006345.5 22 0 - 10 500 JT2-6-5,5x22 35733006345.5 25 0 - 13 500 JT2-6-5,5x25 3573400634Sealing washer V16, Ø 16 mm5.5 19 0 - 4 500 JT2-6-5,5x19-V16 35732216345.5 22 0 - 7 500 JT2-6-5,5x22-V16 3573321634
5.5 25 0 - 10 500 JT2-6-5,5x25-V16 3573421634
EJOT® SAPHIRSelf-drilling screw JT2-6-5,5
J2
APPLICATION RANGE• Fastening of pro� led steel sheets onto
1,5 – 5 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 5,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
45
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIRSelf-drilling screw JT2-8-5,5
J2
APPLICATION RANGE• Fastening of pro� led steel sheets
onto 4 – 8 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Sealing steel washer, zinc-plated• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,5 + 8,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer5.5 25 0 - 12 500 JT2-8-5,5x25 35734006945.5 35 0 - 22 500 JT2-8-5,5x35 3573600694Sealing washer V16, Ø 16 mm5.5 25 0 - 9 500 JT2-8-5,5x25-V16 3573421694
5.5 35 0 - 19 500 JT2-8-5,5x35-V16 3573621694
EJOT® SAPHIR Self-drilling screw JT2-12-5,5
J2
APPLICATION RANGE• Fastening pro� led steel sheets
onto 4 – 12 mm steel substrate
FEATURES• Case-hardened steel• Climadur coated – high-grade coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ......... 1,0 + 12,0 mm / 2,0 + 10,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer (no approval)5.5 35 0 - 13 500 JT2-12-5,5x35 38045009975.5 50 0 - 28 500 JT2-12-5,5x50 38071009975.5 65 9 - 43 250 JT2-12-5,5x65 38075009975.5 80 24 - 58 250 JT2-12-5,5x80 38072009975.5 110 54 - 88 250 JT2-12-5,5x110 38073009975.5 130 74 - 108 200 JT2-12-5,5x130 3807400997Sealing washer V16, Ø 16 mm5.5 35 0 - 10 500 JT2-12-5,5x35-V16 38045219975.5 50 0 - 25 250 JT2-12-5,5x50-V16 38071219975.5 65 6 - 40 250 JT2-12-5,5x65-V16 38075219975.5 80 21 - 55 200 JT2-12-5,5x80-V16 38072219975.5 110 51 - 85 200 JT2-12-5,5x110-V16 38073219975.5 130 71 - 105 200 JT2-12-5,5x130-V16 3807421997
46
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIRSelf-drilling screw JT2-12-6,3
J2
APPLICATION RANGE• Fastening of pro� led steel sheets
onto 4 – 10 mm steel substrate
FEATURES• Case-hardened steel, zinc-plated• Sealing steel washer, zinc-plated• Pre-assembled sealing washer
TECHNICAL DATADrilling capacity t
I + t
II ................................. 2,0 + 10,0 mm
Drive .......................................................... hexagon A/F10
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.3 35 0 - 13 500 JT2-12-6,3x35 3595600614Sealing washer V16, Ø 16 mm6.3 35 0 - 10 250 JT2-12-6,3x35-V16 3595621614
47
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIR Self-drilling screw JT2-D-6H-5,5/6,3
J2
APPLICATION RANGE• Fastening sandwich elements onto 1.5-5 mm steel
substructures
FEATURES• Case-hardened steel• Climadur coated – high-grade coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Sealing steel washer, zinc-plated or stainless steel• Pre-assembled sealing washer• With free spin zone under screw head• High thread
TECHNICAL DATADrive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Self-tapping screw JZ7-6,3 ...................... page 83
Special screwgun DAM 5 .......................... page 180
Ømm
Ø Highthread mm
Length mm
For sandwich panels
PUPrice €/
100 piecesOrder description Part number
Sealing washer E19, Ø 19 mm5.5 6.3 62 32.0 - 44.0 250 JT2-D-6H-5,5/6,3x62-E19 35534126745.5 6.3 82 42.0 - 64.0 200 JT2-D-6H-5,5/6,3x82-E19 35536126745.5 6.3 102 62.0 - 84.0 200 JT2-D-6H-5,5/6,3x102-E19 35538126745.5 6.3 122 82.0 - 104.0 150 JT2-D-6H-5,5/6,3x122-E19 35570126745.5 6.3 152 102.0 - 134.0 100 JT2-D-6H-5,5/6,3x152-E19 35559126745.5 6.3 172 132.0 - 154.0 100 JT2-D-6H-5,5/6,3x172-E19 35564126745.5 6.3 192 152.0 - 174.0 100 JT2-D-6H-5,5/6,3x192-E19 3556612674Sealing washer V16, Ø 16 mm5.5 6.3 62 32.0 - 44.0 250 JT2-D-6H-5,5/6,3x62-V16 35534216745.5 6.3 82 42.0 - 64.0 200 JT2-D-6H-5,5/6,3x82-V16 35536216745.5 6.3 102 62.0 - 84.0 200 JT2-D-6H-5,5/6,3x102-V16 35538216745.5 6.3 122 82.0 - 104.0 150 JT2-D-6H-5,5/6,3x122-V16 35570216745.5 6.3 152 102.0 - 134.0 150 JT2-D-6H-5,5/6,3x152-V16 35559216745.5 6.3 172 132.0 - 154.0 150 JT2-D-6H-5,5/6,3x172-V16 35564216745.5 6.3 192 152.0 - 174.0 100 JT2-D-6H-5,5/6,3x192-V16 3556621674
48
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIR Self-drilling screw
JT2-D-12H-5,5/6,3
J2
APPLICATION RANGE• Fastening sandwich elements onto 3-12 mm steel
substructures
FEATURES• Case-hardened steel• Climadur coated – high-grade coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Sealing steel washer, zinc-plated or stainless steel• Pre-assembled sealing washer• With free spin zone under screw head• High thread
TECHNICAL DATADrive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Self-tapping screw JZ7-6,3 ...................... page 83
Special screwgun DAM5 .......................... page 180
Ømm
Ø Highthread mm
Length mm
For sandwich panels
PUPrice €/
100 piecesOrder description Part number
Sealing washer E19, Ø 19 mm5.5 6.3 80 41.0 - 50.0 200 JT2-D-12H-5,5/6,3x80-E19 35547126145.5 6.3 95 46.0 - 65.0 200 JT2-D-12H-5,5/6,3x95-E19 35549126145.5 6.3 115 60.0 - 85.0 150 JT2-D-12H-5,5/6,3x115-E19 35552126145.5 6.3 135 75.0 - 105.0 150 JT2-D-12H-5,5/6,3x135-E19 35554126145.5 6.3 155 90.0 - 125.0 100 JT2-D-12H-5,5/6,3x155-E19 35557126145.5 6.3 195 120.0 - 165.0 100 JT2-D-12H-5,5/6,3x195-E19 35595126145.5 6.3 235 160.0 - 205.0 100 JT2-D-12H-5,5/6,3x235-E19 35571126145.5 6.3 250 175.0 - 220.0 150 JT2-D-12H-5,5/6,3x250-E19 35572126145.5 6.3 275 200.0 - 245.0 100 JT2-D-12H-5,5/6,3x275-E19 35573126145.5 6.3 300 225.0 - 270.0 100 JT2-D-12H-5,5/6,3x300-E19 3557412614Sealing washer V16, Ø 16 mm5.5 6.3 80 41.0 - 50.0 200 JT2-D-12H-5,5/6,3x80-V16 35547216145.5 6.3 95 46.0 - 65.0 200 JT2-D-12H-5,5/6,3x95-V16 35549216145.5 6.3 115 60.0 - 85.0 200 JT2-D-12H-5,5/6,3x115-V16 35552216145.5 6.3 135 75.0 - 105.0 150 JT2-D-12H-5,5/6,3x135-V16 35554216145.5 6.3 155 90.0 - 125.0 150 JT2-D-12H-5,5/6,3x155-V16 35557216145.5 6.3 195 120.0 - 165.0 150 JT2-D-12H-5,5/6,3x195-V16 35595216145.5 6.3 235 160.0 - 205.0 150 JT2-D-12H-5,5/6,3x235-V16 35571216145.5 6.3 250 175.0 - 220.0 100 JT2-D-12H-5,5/6,3x250-V16 35572216145.5 6.3 275 200.0 - 245.0 100 JT2-D-12H-5,5/6,3x275-V16 35573216145.5 6.3 300 225.0 - 270.0 100 JT2-D-12H-5,5/6,3x300-V16 3557421614
49
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIR Self-drilling screw JT2-FZ-6-6,3
J2
APPLICATION RANGE• Fastening 177/51 sandwich elements onto 1.5-6 mm
steel substructures
FEATURES• Case-hardened steel• Climadur coated – high-grade coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Pre-assembled FZD sealing washer• A2 stainless steel washer • Clearing wings save additional drilling into the
corrugated panel• no forcing tension
TECHNICAL DATADrive ............................................................ hexagon A/F8
NOTEFor the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals.
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
6.3 110 100 JT2-FZ-6-6,3x110-FZD 35122756646.3 150 50 JT2-FZ-6-6,3x150-FZD 3515675608
Order information: Further lengths on request
50
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIR Self-drilling screw JT2-FZ-12-6,3
J2
APPLICATION RANGE• Fastening 177/51 sandwich elements onto 5-12 mm
steel substructures
FEATURES• Case-hardened steel• Climadur coated – high-grade coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Pre-assembled FZD sealing washer• A2 stainless steel washer• Clearing wings save additional drilling into the
corrugated panel• no forcing tension
TECHNICAL DATADrive ............................................................ hexagon A/F8
NOTEFor the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals.
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
6.3 115 100 JT2-FZ-12-6,3x115-FZD 3512375614
51
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
J T 2 s e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
C a s e - h a r d e n e d s t e e l
EJOT® SAPHIRSelf-drilling screw JT2-FZ-F-6,5
J2
APPLICATION RANGE• Fastening of � brous cement corrugated sheets
onto timber substructure
FEATURES• Case-hardened steel, hot-dip zinc-plated• Pre-assembled FZD sealing washer• A2 stainless steel washer • Clearing wings save additional drilling into the
corrugated panel• no forcing tension
APPROVALZ-31.1-144 (Eternit)
TECHNICAL DATADrive ............................................................ hexagon A/F8
NOTESuitable for corrugation 5 when covering with � brous cement corrugated sheets 177/51 onto timber substructure without insulation. For the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals.
CROSS REFERENCEAccessories ............................................ page 191
JT4-FZ-6,5 ............................................. page 72 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
6.5 100 100 JT2-FZ-F-6,5x100-FZD 35151756086.5 130 100 JT2-FZ-F-6,5x130-FZD 35156756086.5 180 50 JT2-FZ-F-6,5x180-FZD 3518075608
EJOT® SAPHIRSelf-drilling screw JT2-ST-2-6,0with countersunk head
APPLICATION RANGE• Fastening wooden parts onto thin-walled steel /
aluminium substrate
FEATURES• Case-hardened steel• Climadur coated – high-grade coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
APPROVALZ-14.4-426
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
6.0 60 17 - 47 500 JT2-ST-2-6,0x60 73821196096.0 80 17 - 67 250 JT2-ST-2-6,0x80 73821126096.0 100 37 - 87 250 JT2-ST-2-6,0x100 73821136096.0 120 57 - 107 250 JT2-ST-2-6,0x120 73821146096.0 140 77 - 127 250 JT2-ST-2-6,0x140 73821156096.0 160 97 - 147 200 JT2-ST-2-6,0x160 73821166096.0 180 117 - 167 200 JT2-ST-2-6,0x180 7382117609
6.0 200 137 - 187 200 JT2-ST-2-6,0x200 7382118609
52
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
N o t e s
© P. Lange DUBAI METRO, DUBAI Supplied by EJOT: EJOT® stainless steel SAPHIR self-drilling screw JT4, EJOT® SAPHIR self-drilling screw JT2
53
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOFAST® Side lap screw JF3-2H-4,8
J3
APPLICATION RANGE• Side lap stitching of pro� led steel sheets• Side lap stitching of pro� led aluminium sheets
FEATURES• A2 stainless steel with innovative point geometry• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching• Non-skid application• Fastening without swarf
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ............................... 0,88 + 0,88 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ø in mm
Length mm
Clamp thickness
in mmPU
Price € / 100
pcs.Order description Part Number
Sealing washer E 14, Ø 14 mm4.8 19 0 - 4 500 JF3-2H-4,8x19-E14 3591977391Sealing washer E 16, Ø 16 mm4.8 19 0 - 4 500 JF3-2H-4,8x19-E16 3591911391
EJOT® SUPER-SAPHIR Self-drilling screw JT3-2H-4,8
J3
APPLICATION RANGE• Side lap stitching of pro� led steel sheets• Side lap stitching of pro� led aluminium sheets
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E14, Ø 14 mm4.8 19 0 - 4 1,000 JT3-2H-4,8x19-E14 3591977351Sealing washer E16, Ø 16 mm4.8 19 0 - 4 500 JT3-2H-4,8x19-E16 3591911351
54
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-2-4,9
J3
APPLICATION RANGE• For fixing profiled steel sheets
to timber substructure• For fixing aluminium profiled sheets
to timber substructure• For fixing roofing sheets to
timber substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• Thread according to DIN 7998
APPROVALZ-14.1-537
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E14, Ø 14 mm4.9 35 500 JT3-2-4,9x35-E14 3593509321Sealing washer E16, Ø 16 mm4.9 35 500 JT3-2-4,9x35-E16 3593511321
4.9 70 250 JT3-2-4,9x70-E16 3597011321
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-FR-2H-4,8
with truss head
APPLICATION RANGE• Side lap stitching of corrugated profile steel sheets• Side lap stitching of corrugated pro� le aluminium sheets
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 1,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm4.8 19 0 - 4 1,000 JT3-FR-2H-4,8x19-E11 3591968358
55
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-FR-2-4,9with truss head
APPLICATION RANGE• For fixing corrugated pro� le steel sheets
to timber substructure• For � xing corrugated pro� le aluminium sheets
to timber substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• Thread according to DIN 7998
APPROVALZ-14.1-537
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm4.9 35 500 JT3-FR-2-4,9x35-E11 3593568328
Ømm
Length mm
Clamp thickness
mmPU
Price €/100 pcs.
Order description Part number
Sealing washer E16, Ø 16 mm5.5 25 0 - 10 500 JT3-2H-Plus-5,5x25-E16 35922113915.5 30 0 - 15 500 JT3-2H-Plus-5,5x30-E16 35923113915.5 35 0 - 20 - JT3-2H-Plus-5,5x35-E16 3592511391Sealing washer E22, Ø 22 mm5.5 25 0 - 10 500 JT3-2H-Plus-5,5x25-E22 35922133915.5 30 0 - 15 - JT3-2H-Plus-5,5x30-E22 35923133915.5 35 0 - 20 - JT3-2H-Plus-5,5x35-E22 3592513391
EJOT® SUPER-SAPHIR Self-drilling screw JT3-2H-Plus-5,5
J3
APPLICATION RANGE• Side lap stitching of pro� led steel sheets• Side lap stitching of pro� led aluminium sheets• For � xing pro� led steel sheets to
cassette system walls • For � xing pro� led aluminium sheets
to cassette system walls
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching
APPROVALZ-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 2,5 mm
Drive ......................................................................... A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
56
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
Ømm
Length mm
Clamp thickness
mmPU
Price €/100 pcs.
Order description Part number
Sealing washer E11, Ø 11 mm5.5 25 0 - 10 1,000 JT3-FR-2H-Plus-5,5x25-E11 3592269398
EJOT® SUPER-SAPHIR Self-drilling screw JT3-FR-2H-Plus-5,5
APPLICATION RANGE• Side lap stitching of pro� led steel sheets• Side lap stitching of pro� led aluminium sheets• For � xing pro� led steel sheets to
cassette system walls • For � xing pro� led aluminium sheets
to cassette system walls
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching
APPROVALZ-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 2,5 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
57
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-2-6,0
J3
APPLICATION RANGE • For fixing pro� led sheets with/without
intermediate insulation to thin-walled steel / aluminium substructure as well as timber substructure
APPROVALZ-14.4-426Z-14.1-537
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm6.0 25 0 - 7 500 JT3-2-6x25-E16 35955113216.0 120 53 - 103 150 JT3-2-6x120-E16 35952113216.0 140 73 - 123 150 JT3-2-6x140-E16 35958113216.0 160 93 - 143 150 JT3-2-6x160-E16 3595911321Sealing washer E22, Ø 22 mm6.0 25 0 - 7 500 JT3-2-6x25-E22 35955133216.0 120 53 - 103 200 JT3-2-6x120-E22 35952133216.0 140 73 - 123 100 JT3-2-6x140-E22 35958133216.0 160 93 - 143 100 JT3-2-6x160-E22 3595913321
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm5.6 35 500 50.10 JT3-2-5,6x35-E16 3594511321Sealing washer E22, Ø 22 mm5.6 35 500 54.80 JT3-2-5,6x35-E22 3594513321
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-2-5,6
J3
APPLICATION RANGE• For � xing pro� led steel sheets
to timber substructure• For � xing aluminium pro� led sheets
to timber substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrilling capacity tI + tII.............................................2,0 mmDrive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
58
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
Ømm
Length mm
For sandwich panels
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm6.5 50 - 250 JT3-2-6,5x50-E16 35988113216.5 65 - 250 JT3-2-6,5x65-E16 35989113216.5 80 - 200 JT3-2-6,5x80-E16 35980113216.5 100 20 - 40 200 JT3-2-6,5x100-E16 35981113216.5 120 40 - 60 150 JT3-2-6,5x120-E16 35983113216.5 140 60 - 80 150 JT3-2-6,5x140-E16 35985113216.5 160 80 - 100 150 JT3-2-6,5x160-E16 35987113216.5 180 100 - 120 100 JT3-2-6,5x180-E16 35982113216.5 200 120 - 140 100 JT3-2-6,5x200-E16 35990113216.5 220 140 - 160 100 JT3-2-6,5x220-E16 35991113216.5 240 160 - 180 100 JT3-2-6,5x240-E16 3599211321Sealing washer E22, Ø 22 mm6.5 50 - 250 JT3-2-6,5x50-E22 35988133216.5 65 - 250 JT3-2-6,5x65-E22 35989133216.5 80 - 150 JT3-2-6,5x80-E22 35980133216.5 100 20 - 40 150 JT3-2-6,5x100-E22 35981133216.5 120 40 - 60 100 JT3-2-6,5x120-E22 35983133216.5 140 60 - 80 100 JT3-2-6,5x140-E22 35985133216.5 160 80 - 100 100 JT3-2-6,5x160-E22 35987133216.5 180 100 - 120 100 JT3-2-6,5x180-E22 3598213321
6.5 200 120 - 140 100 JT3-2-6,5x200-E22 35990133216.5 220 140 - 160 100 JT3-2-6,5x220-E22 35991133216.5 240 160 - 180 50 JT3-2-6,5x240-E22 3599213321
EJOT® SUPER-SAPHIR Self-drilling screw JT3-2-6,5
J3
APPLICATION RANGE• For � xing pro� led steel sheets
to timber substructure• For � xing pro� led aluminium sheets
to timber substructure• For � xing sandwich panels
to timber substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.4-407Z-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ............................................ 2,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Storm washers ........................................ page 85
Self-tapping screw JA3-6,5 ...................... page 78
Special screwgun DAM5 .......................... page 180
Special screwgun DAM5-SH2 ................... page 181
59
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-3-5,5
J3
APPLICATION RANGE• For fixing pro� led steel sheets
to 1 – 2,5 mm steel substructure• For � xing pro� led aluminium sheets to 1 – 2,5 mm
aluminium or steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 2,5 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-2H-Plus-5,5 .......... page 55
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm5.5 25 0 - 7 500 JT3-3-5,5x25-E16 35922113315.5 35 0 - 16 500 JT3-3-5,5x35-E16 35925113315.5 50 0 - 31 250 JT3-3-5,5x50-E16 3592811331
5.5 70 0 - 51 250 JT3-3-5,5x70-E16 3593911331
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-FR-3-5,5with truss head
APPLICATION RANGE• For fixing corrugated pro� le steel sheets
to 1 – 2,5 mm steel substructure• For � xing corrugated pro� le aluminium sheets to 1 – 2,5
mm aluminium or steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 2,5 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm5.5 50 0 - 31 500 JT3-FR-3-5,5x50-E11 3592869335
60
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm5.5 25 0 - 7 500 JT3-6-5,5x25-E16 35722113615.5 30 0 - 11 500 JT3-6-5,5x30-E16 35723113615.5 35 0 - 16 500 JT3-6-5,5x35-E16 35725113615.5 50 0 - 31 250 JT3-6-5,5x50-E16 35928113615.5 70 20 - 51 250 JT3-6-5,5x70-E16 35939113615.5 90 40 - 71 200 JT3-6-5,5x90-E16 35961113615.5 110 60 - 91 200 JT3-6-5,5x110-E16 35962113615.5 130 80 - 111 200 JT3-6-5,5x130-E16 35963113615.5 150 100 - 131 150 JT3-6-5,5x150-E16 35964113615.5 170 120 - 151 150 JT3-6-5,5x170-E16 35965113615.5 190 140 - 171 100 JT3-6-5,5x190-E16 3596611361Sealing washer E22, Ø 22 mm5.5 25 0 - 7 500 JT3-6-5,5x25-E22 35722133615.5 30 0 - 11 500 JT3-6-5,5x30-E22 35723133615.5 35 0 - 16 500 JT3-6-5,5x35-E22 35725133615.5 50 0 - 31 250 JT3-6-5,5x50-E22 35928133615.5 70 20 - 51 200 JT3-6-5,5x70-E22 35939133615.5 90 40 - 71 150 JT3-6-5,5x90-E22 35961133615.5 110 60 - 91 150 JT3-6-5,5x110-E22 35962133615.5 130 80 - 111 100 JT3-6-5,5x130-E22 35963133615.5 150 100 - 131 100 JT3-6-5,5x150-E22 35964133615.5 170 120 - 151 100 JT3-6-5,5x170-E22 3596513361
5.5 190 140 - 171 100 JT3-6-5,5x190-E22 3596613361
EJOT® SUPER-SAPHIR Self-drilling screw JT3-6-5,5
J3
APPLICATION RANGE• For fixing pro� led steel sheets
to 1.5 – 5 mm steel substructure• For � xing pro� led aluminium sheets / sandwich panels to
1,5 – 5 mm aluminium or steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.4-407Z-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 5,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Storm washers ........................................ page 85
Self-tapping screw JZ3-6,3 ...................... page 80
Special screwgun DAM5 .......................... page 180
Special screwgun DAM5-SH2 .................... page 181
61
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-FR-6-5,5with truss head
APPLICATION RANGE• For fixing corrugated pro� le steel sheets
to 1.5 – 5 mm steel substructure• For � xing corrugated pro� le aluminium sheets to 1,5 – 5
mm aluminium or steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 5,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm5.5 25 0 - 7 1,000 JT3-FR-6-5,5x25-E11 3592269368Sealing washer E11, Ø 11 mm5.5 35 0 - 17 500 JT3-FR-6-5,5x35-E11 3592569368
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm6.3 25 7 500 JT3-6-6,3x25-E16 3599411361Sealing washer E22, Ø 22 mm6.3 25 7 500 JT3-6-6,3x25-E22 3599413361
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-6-6,3
J3
APPLICATION RANGE• For fixing pro� led steel sheets
to 1.5 – 5 mm steel substructure• For � xing pro� led aluminium sheets
to 1,5 – 5 mm aluminium or steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 5,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
62
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-12-5,5
J3
APPLICATION RANGE• For fixing pro� led steel sheets
to 4 – 10 mm steel substructure• For � xing pro� led aluminium sheets / sandwich panels to
4-10 mm steel substructure• For � xing pro� led aluminium sheets / sandwich panels to
4 – 12 mm aluminium substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.4-407 Z-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II 2,0 + 10,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Storm washers ........................................ page 85
Self-tapping screw JZ3-6,3 ...................... page 80
Special screwgun DAM5 .......................... page 180 Special screwgun DAM5-SH2 ................... page 181
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm5.5 40 0 - 11 500 JT3-12-5,5x40-E16 35956113115.5 58 0 - 31 500 JT3-12-5,5x58-E16 35958113115.5 78 20 - 51 250 JT3-12-5,5x78-E16 35950113115.5 98 40 - 71 250 JT3-12-5,5x98-E16 35951113115.5 118 60 - 91 150 JT3-12-5,5x118-E16 35952113115.5 138 80 - 111 150 JT3-12-5,5x138-E16 35953113115.5 158 100 - 131 150 JT3-12-5,5x158-E16 35954113115.5 178 120 - 151 150 JT3-12-5,5x178-E16 35955113115.5 198 140 - 171 100 JT3-12-5,5x198-E16 3595711311Sealing washer E22, Ø 22 mm5.5 40 0 - 11 250 JT3-12-5,5x40-E22 35956133115.5 58 0 - 31 500 JT3-12-5,5x58-E22 35958133115.5 78 20 - 51 200 JT3-12-5,5x78-E22 35950133115.5 98 40 - 71 150 JT3-12-5,5x98-E22 35951133115.5 118 60 - 91 150 JT3-12-5,5x118-E22 35952133115.5 138 80 - 111 100 JT3-12-5,5x138-E22 35953133115.5 158 100 - 131 100 JT3-12-5,5x158-E22 35954133115.5 178 120 - 151 100 JT3-12-5,5x178-E22 3595513311
5.5 198 140 - 171 100 JT3-12-5,5x198-E22 3595713311
63
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-FR-12-5,5with truss head
APPLICATION RANGE• For fixing corrugated pro� le steel sheets
to 4 – 10 mm steel substructure• For � xing corrugated pro� le aluminium sheets
to 4 – 10 mm steel substructure• For � xing corrugated pro� le aluminium sheets
to 4 – 12 mm aluminium substructure
FEATURES• A2 stainless steel, with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALZ-14.1-537ETA-10/0200
TECHNICAL DATADrilling capacity t
I + t
II ................................. 2,0 + 10,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm5.5 40 11 500 JT3-FR-12-5,5x40-E11 3595669318
64
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-D-6H-5,5/6,3
J3
APPLICATION RANGE• For fixing sandwich panels
to 1,5 – 5 mm steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head• High thread
APPROVALZ-14.4-407
TECHNICAL DATADrive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-6-5,5 .................... page 60
Self-tapping screw JZ3-6,3 ...................... page 80
Self-tapping screw JZ7-6,3 ...................... page 83
Special screwgun DAM5 .......................... page 180
Ømm
Ø highthread mm
Length mm
For sandwich panels
PUPrice €/
100 piecesOrder description Part number
Sealing washer E16, Ø 16 mm5.5 6.3 67 35.0 - 40.0 250 JT3-D-6H-5,5/6,3x67-E16 35545113725.5 6.3 87 48.0 - 60.0 200 JT3-D-6H-5,5/6,3x87-E16 35560113715.5 6.3 107 58.0 - 80.0 200 JT3-D-6H-5,5/6,3x107-E16 35561113715.5 6.3 127 72.0 - 100.0 150 JT3-D-6H-5,5/6,3x127-E16 35562113715.5 6.3 147 92.0 - 120.0 150 JT3-D-6H-5,5/6,3x147-E16 35563113715.5 6.3 167 112.0 - 140.0 150 JT3-D-6H-5,5/6,3x167-E16 35567113715.5 6.3 197 140.0 - 170.0 100 JT3-D-6H-5,5/6,3x197-E16 35597113725.5 6.3 237 170.0 - 210.0 100 JT3-D-6H-5,5/6,3x237-E16 3559611372Sealing washer E19, Ø 19 mm5.5 6.3 67 35.0 - 40.0 250 JT3-D-6H-5,5/6,3x67-E19 35545663725.5 6.3 87 48.0 - 60.0 200 JT3-D-6H-5,5/6,3x87-E19 35560663715.5 6.3 107 58.0 - 80.0 200 JT3-D-6H-5,5/6,3x107-E19 35561663715.5 6.3 127 72.0 - 100.0 150 JT3-D-6H-5,5/6,3x127-E19 35562663715.5 6.3 147 92.0 - 120.0 150 JT3-D-6H-5,5/6,3x147-E19 35563663715.5 6.3 167 112.0 - 140.0 150 JT3-D-6H-5,5/6,3x167-E19 35567663715.5 6.3 197 140.0 - 170.0 100 JT3-D-6H-5,5/6,3x197-E19 35597663725.5 6.3 237 170.0 - 210.0 100 JT3-D-6H-5,5/6,3x237-E19 3559666372Sealing washer E22, Ø 22 mm5.5 6.3 67 35.0 - 40.0 200 JT3-D-6H-5,5/6,3x67-E22 35545133725.5 6.3 87 48.0 - 60.0 150 JT3-D-6H-5,5/6,3x87-E22 35560133715.5 6.3 107 58.0 - 80.0 150 JT3-D-6H-5,5/6,3x107-E22 35561133715.5 6.3 127 72.0 - 100.0 100 JT3-D-6H-5,5/6,3x127-E22 35562133715.5 6.3 147 92.0 - 120.0 100 JT3-D-6H-5,5/6,3x147-E22 35563133715.5 6.3 167 112.0 - 140.0 100 JT3-D-6H-5,5/6,3x167-E22 35567133715.5 6.3 197 140.0 - 170.0 100 JT3-D-6H-5,5/6,3x197-E22 35597133725.5 6.3 237 170.0 - 210.0 50 JT3-D-6H-5,5/6,3x237-E22 3559613372
Order information: Further lengths upon request.
65
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-D-12H-5,5/6,3
J3
APPLICATION RANGE• For fixing sandwich panels
to 3 – 10 mm steel substructure
FEATURES• A2 stainless steel with hardened drill point• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head• High thread
APPROVALZ-14.4-407
TECHNICAL DATADrive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-12-5,5 .................. page 60
Self-tapping screw JZ3-6,3 ...................... page 80
Self-tapping screw JZ7-6,3 ...................... page 83
Special screwgun DAM5 .......................... page 180
Ømm
Ø highthread mm
Length mm
For sandwich panels
PUPrice €/
100 piecesOrder description Part number
Sealing washer E16, Ø 16 mm5.5 6.3 75 36.0 - 40.0 250 JT3-D-12H-5,5/6,3x75-E16 35575113125.5 6.3 95 48.0 - 60.0 200 JT3-D-12H-5,5/6,3x95-E16 35549113115.5 6.3 115 58.0 - 80.0 200 JT3-D-12H-5,5/6,3x115-E16 35552113115.5 6.3 135 72.0 - 100.0 150 JT3-D-12H-5,5/6,3x135-E16 35554113115.5 6.3 155 92.0 - 120.0 150 JT3-D-12H-5,5/6,3x155-E16 35557113115.5 6.3 175 110.0 - 140.0 150 JT3-D-12H-5,5/6,3x175-E16 35565113125.5 6.3 195 130.0 - 160.0 150 JT3-D-12H-5,5/6,3x195-E16 35595113125.5 6.3 245 170.0 - 210.0 100 JT3-D-12H-5,5/6,3x245-E16 3559811312Sealing washer E19, Ø 19 mm5.5 6.3 75 36.0 - 40.0 200 JT3-D-12H-5,5/6,3x75-E19 35575663125.5 6.3 95 48.0 - 60.0 200 JT3-D-12H-5,5/6,3x95-E19 35549663115.5 6.3 115 58.0 - 80.0 150 JT3-D-12H-5,5/6,3x115-E19 35552663115.5 6.3 135 72.0 - 100.0 150 JT3-D-12H-5,5/6,3x135-E19 35554663115.5 6.3 155 92.0 - 120.0 100 JT3-D-12H-5,5/6,3x155-E19 35557663115.5 6.3 175 110.0 - 140.0 100 JT3-D-12H-5,5/6,3x175-E19 35565663125.5 6.3 195 130.0 - 160.0 100 JT3-D-12H-5,5/6,3x195-E19 35595663125.5 6.3 245 170.0 - 210.0 100 JT3-D-12H-5,5/6,3x245-E19 3559866312Sealing washer E22, Ø 22 mm5.5 6.3 75 36.0 - 40.0 200 JT3-D-12H-5,5/6,3x75-E22 35575133125.5 6.3 95 48.0 - 60.0 200 JT3-D-12H-5,5/6,3x95-E22 35549133115.5 6.3 115 58.0 - 80.0 150 JT3-D-12H-5,5/6,3x115-E22 35552133115.5 6.3 135 72.0 - 100.0 100 JT3-D-12H-5,5/6,3x135-E22 35554133115.5 6.3 155 92.0 - 120.0 100 JT3-D-12H-5,5/6,3x155-E22 35557133115.5 6.3 175 110.0 - 140.0 100 JT3-D-12H-5,5/6,3x175-E22 35565133125.5 6.3 195 130.0 - 160.0 100 JT3-D-12H-5,5/6,3x195-E22 35595133125.5 6.3 245 170.0 - 210.0 150 JT3-D-12H-5,5/6,3x245-E22 3559813312
Order information: Further lengths upon request.
66
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 3 / J F 3
Sel
f-dr
illi
ng
scre
ws
A 2 s t a i n l e s s s t e e l w i t h s t e e l p o i n t
EJOT® SUPER-SAPHIR Self-drilling screw JT3-X-2-6,0
J3
APPLICATION RANGE• For fixing standing seam systems (clips)
to 0,55 – 1,25 mm steel substructure• For � xing standing seam systems (clips)
to 0,8 – 1,5 mm aluminium substructureand timber substructureEmbedment depth acc. to the approval 18 – 24 mm
FEATURES• A2 stainless steel with hardened drill point• Under-head serrations to increase the installation
reliability• Special thread for thin-walled components• High stripping torque• Installation without special tools
APPROVALZ-14.4-426
TECHNICAL DATADrive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
6.0 25 0 - 10 500 JT3-X-2-6x25 73805393016.0 36 0 - 20 500 JT3-X-2-6x36 7380516301
6.0 46 0 - 30 500 JT3-X-2-6x46 7380517301
EJOT® SUPER-SAPHIRSelf-drilling screw JT3-ST-2-6,0
with countersunk head
APPLICATION RANGE• For fixing rail systems with intermediate insulation to
thin-walled steel / aluminium substructure as well as timber substructure
• For � xing wooden parts onto thin-walled steel / aluminium substructure
FEATURES• A2 stainless steel with hardened drill point
APPROVALZ-14.4-426
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
6.0 60 17 - 45 250 JT3-ST-2-6,0x60 73821253016.0 80 17 - 65 250 JT3-ST-2-6,0x80 73821073016.0 100 37 - 85 250 JT3-ST-2-6,0x100 73821013016.0 120 57 - 105 200 JT3-ST-2-6,0x120 73821023016.0 140 77 - 125 150 JT3-ST-2-6,0x140 73821033016.0 160 97 - 145 150 JT3-ST-2-6,0x160 73821043016.0 180 117 - 165 150 JT3-ST-2-6,0x180 7382105301
6.0 200 137 - 185 150 JT3-ST-2-6,0x200 7382106301
67
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
wsEJOT® stainless steel SAPHIR
Self-drilling screw JT4-2-4,8
J4
APPLICATION RANGE• Especially suited for � xing aluminium pro� les to
aluminium substructure
FEATURES• A2 stainless steel• Stainless steel sealing washer
TECHNICAL DATADrilling capacity t
I + t
II ................................... 1,0 + 1,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.8 19 0 - 9 1,000 JT4-2-4,8x19 7380402300Sealing washer E14, Ø 14 mm4.8 19 0 - 6 1,000 JT4-2-4,8x19-E14 3501909420
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-FR-2H-4,8with truss head
APPLICATION RANGE• Side lap stitching of aluminium corrugated profile sheets
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer• With free spin zone under screw head for side lap
stitching
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 1,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm4.8 19 0 - 6 1,000 JT4-FR-2H-4,8x19-E11 3501968458
68
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
ws
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-ZT-3-4,2
with � at head
APPLICATION RANGE• For � xing aluminium pro� les to aluminium
substructure � 2 mm
FEATURES• A2 stainless steel
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 2,0 mm
Drive ............................................ Hexalobular / TORX® T20
CROSS REFERENCEAccessories ............................................ page 68
Special screwgun DAM5 .......................... page 68
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.2 13 0 - 7 1,000 JT4-ZT-3-4,2x13 7381098300
4.2 16 0 - 10 1,000 JT4-ZT-3-4,2x16 7381074300
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-FR-2-4,9
with truss head
APPLICATION RANGE• For � xing aluminium corrugated pro� le sheets
to timber substructure• For � xing facade panels to timber substructure
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer• Thread according to DIN 7998
APPROVALZ-14.1-537
TECHNICAL DATADrilling capacity .............................................. 0,5 - 2,0 mm Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E11, Ø 11 mm4.9 35 500 JT4-FR-2-4,9x35-E11 3503568420
69
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
wsEJOT® stainless steel SAPHIR
Self-drilling screw JT4-3H/5-5,5
J4
APPLICATION RANGE• To form � oating and � xed points on aluminium
substructures of rear ventilated facades
FEATURES• A2 stainless steel• Installation without depth control / torque clutch• Exact design of fixed or floating points• Flange head, Ø 13 mm
TEST CERTIFICATEP-BWU02-118016
TECHNICAL DATADrilling capacity ......................................................2,0 mm Drive ............................................................ hexagon A/F8
NOTESelf-drilling screw for fastening 3mm pre-drilled wall support to 2 mm pro� le. Component
I: 3,0 mm / Bauteil
II: 1,6 – 2,0 mm
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
5.5 19 1,000 JT4-3H/5-5,5x19* 7380540300 *JT9 made of A4 stainless steel, upon request
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-4-4,8
J4
APPLICATION RANGE• For � xing aluminium pro� les to aluminium
substructure � 3 mm
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVAL / TEST CERTIFICATEZ-14.1-537P-043606P-043609
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 3,0 mm
Drive ............................................................ hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.8 19 0 - 11 1,000 JT4-4-4,8x19 7380387300Sealing washer E11, Ø 11 mm4.8 19 0 - 8 1,000 JT4-4-4,8x19-E11 3501968440Sealing washer E14, Ø 14 mm4.8 19 0 - 8 1,000 JT4-4-4,8x19-E14 3501909440
70
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
ws EJOT® stainless steel SAPHIR
Self-drilling screw JT4-FR-4-4,8with truss head
APPLICATION RANGE• For � xing aluminium corrugated pro� le sheets to
aluminium substructure � 3 mm• For � xing facade panels to aluminium substructure
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 3,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.8 19 0 - 11 1,000 JT4-FR-4-4,8x19 7381095300Sealing washer E11, Ø 11 mm4.8 19 0 - 8 1,000 JT4-FR-4-4,8x19-E11 3501968448Sealing washer E14, Ø 14 mm4.8 19 0 - 8 1,000 JT4-FR-4-4,8x19-E14 3501909448
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-ZT-4-4,8
with � at head
APPLICATION RANGE• For � xing aluminium pro� les to aluminium substructure
�3 mm
FEATURES• A2 stainless steel
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 3,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.8 19 0 - 11 1,000 JT4-ZT-4-4,8x19 7381118300
4.8 25 0 - 17 1,000 JT4-ZT-4-4,8x25 7381129300
71
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
wsEJOT® stainless steel SAPHIR
Self-drilling screw JT4-FR-4-5,5with truss head
APPLICATION RANGE• For � xing aluminium corrugated pro� le sheets to
aluminium substructure � 3 mm• For � xing facade panels to aluminium substructure
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrilling capacity t
I + t
II ....................................1,0 + 3,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer5.5 19 0 - 11 1,000 JT4-FR-4-5,5x19 7381138300Sealing washer E11, Ø 11 mm5.5 19 0 - 8 1,000 JT4-FR-4-5,5x19-E11 3501869448
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer5.5 19 0 - 7 1,000 JT4-6-5,5x19 73804543015.5 22 0 - 10 1,000 JT4-6-5,5x22* 73805083015.5 30 0 - 18 500 JT4-6-5,5x30 7380509301Sealing washer E14, Ø 14 mm5.5 19 0 - 4 500 JT4-6-5,5x19-E14 35018094605.5 22 0 - 7 1,000 JT4-6-5,5x22-E14 35021094605.5 30 0 - 15 500 JT4-6-5,5x30-E14 3502309461Sealing washer E16, Ø 16 mm5.5 22 0 - 7 500 JT4-6-5,5x22-E16 35021114605.5 30 0 - 15 500 JT4-6-5,5x30-E16 3502311461 *JT9 made of A4 stainless steel, upon request
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-6-5,5
J4
APPLICATION RANGE• Fastening aluminium pro� les to aluminium
substructure � 4 mm
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVAL / TEST CERTIFICATEZ-14.1-537P-043609
TECHNICAL DATADrilling capacity t
I + t
II ....................................2,0 + 4,0 mm
drive............................................................. hexagon A/F8
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
72
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
ws EJOT® stainless steel SAPHIR
Self-drilling screw JT4-FZ-6,5
J4
APPLICATION RANGE• For � xing � bre cement corrugated sheets to timber
substructures
FEATURES• A2 stainless steel• Pre-assembled FZD sealing washer• A2 stainless steel washer • Screw wings save additional drilling into the corrugated
slabs• No forcing tension
APPROVALZ-31.1-144 (Eternit)
TECHNICAL DATAdrive............................................................. hexagon A/F8
NOTESuitable for covering with � bre cement corrugated sheets pro� le 177/51 P5 and P6 to timber substructure without insulation. For the dimensioning and the use of fastening materials please note the manufacturer's instructions for use as well as the national approvals.
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT2-FZ-F-6,5 ............... page 51 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
6.5 130 100 JT4-FZ-6,5x130-FZD 3515675400
73
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - d r i l l i n g s c r e w s J T 4A 2 s t a i n l e s s s t e e l
Sel
f-dr
illi
ng
scre
wsEJOT® stainless steel SAPHIR
Self-drilling screw JT4-S-2-4,8
APPLICATION RANGE• For � xing timber laths to aluminium substructure � 2 mm
FEATURES• A2 stainless steel• Countersunk head with milling ribs
TEST CERTIFICATEP-013604P-BWU02-064191
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
For timber thicknesses
in mmPU
Price €/100 pcs.
Order description Part number
4.8 38 20 - 30 500 JT4-S-2-4,8x38 73820863004.8 48 30 - 40 500 JT4-S-2-4,8x48 7382072300
EJOT® stainless steel SAPHIRSelf-drilling screw JT4-STS-3-4,8
APPLICATION RANGE• For � xing facade panels to aluminium substructure
� 3 mm
FEATURES• A2 stainless steel• Countersunk head with flange
TECHNICAL DATADrilling capacity t
I + t
II .............................................3,0 mm
Drive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
4.8 35 0 - 27 500 JT4-STS-3-4,8x35 7384094300
74
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - d r i l l i n g s c r e w s
Sel
f-dr
illi
ng
scre
ws
N o t e s
© P. Lange THE DUBAI MALL, DUBAIDelivered by EJOT: EJOT® Self-tapping screw JZ3
75
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
Sel
f-ta
ppin
g sc
rew
s
EJOT® Self-tapping screws
JA2/JZ2 JA3/JZ3 JA1/JZ1Corremaks®
JZ7CRONIMAKS®
ScrewMaterial
Case-hardened steel,
zinc-platedA2 stainless steel
A5 stainless steel(1.4529)
A2 stainless steel
For components made of
steel/woodsteel/aluminium/
woodsteel/aluminium/
woodSteel S 355 (St 52) or stainless steel
PRODUCT VERSIONS EJOT® Self-tapping screws
ADVANTAGES:• Tap the thread in a pre-drilled core hole• Available with captive sealing washer upon request• All-purposeall-purpose
FEATURES• Hexagon or hexalobular drive / TORX®
• Available in stainless steel, steeland aluminium (upon request)
• Zinc-plated sealing washer made of steel or stainless steel with vulcanised elastomer. Excellent atmospheric - and UV-resistance.
CROSS REFERENCEApplication advice ................................... page 6 Information ............................................. page 8
Selecting the fastener
SELF-TAPPING SCREWL = a + 20 mm
For self-tapping fasteners without drill point the cylindrical part of the screw has to be fastened at least 6 mm into the load-bearing component. In practice 20 mm are added to the sum of the thickness of all components that are fastened onto the substructure. The result is the minimum screw length of a self-tapping screw under consideration of sealing washer and assembly unevenness.
DRILL HOLE-Ø FOR PROFILED STEEL SHEET-DESIGNS
Component thickness tII mm
Hot dip galvanised sheet steel / sectional steel, � at steel St 37 (Rm � 360 N/mm² � 440 N/mm²)
0.63 0.75 0.88 1.00 1.13 1.25 1.502x
0.752x
0.882x
1.002.0 - 4.9 5.0 - 6.9 �7.0 1.5 - 5.9 6.0 - 7.9 8.0 - 9.9 �10.0
Drill-hole Ø: 3.5 4.0 4.5 4.5 4.5 4.5 5.0 4.5 5.0 5.0 5.3 5.5 5.7 6.8 7.0 7.2 7.4EJOT® Screw Type JA Ø 6,5 / JB Ø 6,3 JZ Ø 6,3 JZ Ø 8,0
DRILL HOLE-Ø FOR ALUMINIUM PROFILED SHEET-DESIGNS/*
Component thickness tII mm
Aluminium sheet, aluminium extrusion pro� leF22 up to F 25 (Rm � 220 N/mm² � 290 N/mm²)
up to 0.9 1.0 - 1.4 1.5 - 2.9 3.0 - 4.9 � 5.0Drill-hole Ø: 4.0 4.0 4.5 5.0 5.3EJOT® Screw Type JA Ø 6,5 / JB Ø 6,3 JZ Ø 6,3
* When fastening aluminium pro� led sheet (component I) onto steel substrate (component II) the drill-hole-Ø from the chart for pro� led steel sheet designs apply.
Coarse thread with point (JA)
Fine pitch thread with dog point (JZ)
Component I
Component I
Component II
Component II
a
76
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - t a p p i n g s c r e w s J A 2 / J Z 2S t e e l
Sel
f-ta
ppin
g sc
rew
s
EJOT®
Self-tapping screw JA2-6,5
J2
APPLICATION RANGE• Fixing pro� led steel sheets to timber substructure • Fixing pro� led steel sheets to 2 mm steel substrate• Side lap stitching
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Packa-ging unit
Price €/100 pcs.
Order description Part number
Sealing washer V16, Ø 16 mm6.5 19 500 JA2-6,5x19-V16 31831216546.5 25 500 JA2-6,5x25-V16 31832216546.5 32 500 JA2-6,5x32-V16 31833216546.5 38 500 JA2-6,5x38-V16 31834216546.5 50 250 JA2-6,5x50-V16 31836216546.5 64 250 JA2-6,5x64-V16 31838216546.5 75 250 JA2-6,5x75-V16 31839216546.5 90 200 JA2-6,5x90-V16 31841216546.5 100 200 JA2-6,5x100-V16 31842216546.5 125 150 JA2-6,5x125-V16 31144216516.5 150 100 JA2-6,5x150-V16 31146216516.5 175 100 JA2-6,5x175-V16 3114721651
6.5 200 100 JA2-6,5x200-V16 3114821651
Ømm
Length mm
Packa-ging unit
Price €/100 pcs.
Order description Part number
Sealing washer V16, Ø 16 mm6.3 19 500 JZ2-6,3x19-V16 31811216546.3 25 500 JZ2-6,3x25-V16 31812216546.3 32 500 JZ2-6,3x32-V16 31813216546.3 38 500 JZ2-6,3x38-V16 31814216546.3 50 250 JZ2-6,3x50-V16 31816216546.3 64 250 JZ2-6,3x64-V16 31818216546.3 80 200 JZ2-6,3x80-V16 31820216546.3 90 200 JZ2-6,3x90-V16 31821216546.3 100 200 JZ2-6,3x100-V16 31822216546.3 125 150 JZ2-6,3x125-V16 31124216516.3 150 100 JZ2-6,3x150-V16 31126216516.3 175 100 JZ2-6,3x175-V16 31127216516.3 200 100 JZ2-6,3x200-V16 3112821651
EJOT®
Self-tapping screw JZ2-6,3
J2
APPLICATION RANGE• Fixing pro� led steel sheets to steel substrate
FEATURES• Case-hardened steel, zinc-plated• Steel sealing washer, zinc-plated• Pre-assembled sealing washer
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
77
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w sN o t e s
Sel
f-ta
ppin
g sc
rew
s
ATOMIUM, BRUSSELS, BELGIUM © CUiNZSupplied by EJOT: EJOT® SUPER-SAPHIR Self-drilling screw JT3
78
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - t a p p i n g s c r e w s J A 3 / J Z 3
Sel
f-ta
ppin
g sc
rew
s
A 2 s t a i n l e s s s t e e l
EJOT®
Self-tapping screw JA3-6,5
J3
APPLICATION RANGE• For � xing pro� led steel sheets to timber substructure• For � xing sandwich panels to timber substructure• For � xing pro� led steel / aluminium sheet to � 2 mm steel
substructure• Side lap stitching of pro� led steel / aluminium sheet
APPROVALETA-10/0200Z-14.4-407Z-14.1-537
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-2-6,5 .................... page 58 Storm washers ........................................ page 85 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm6.5 19 500 JA3-6,5x19-E16 31131113116.5 25 500 JA3-6,5x25-E16 31132113116.5 32 500 JA3-6,5x32-E16 31133113116.5 38 500 JA3-6,5x38-E16 31134113116.5 45 500 JA3-6,5x45-E16 31135113116.5 50 250 JA3-6,5x50-E16 31136113116.5 64 250 JA3-6,5x64-E16 31138113116.5 75 250 JA3-6,5x75-E16 31139113116.5 90 200 JA3-6,5x90-E16 31141113116.5 100 200 JA3-6,5x100-E16 31142113116.5 115 150 JA3-6,5x115-E16 31143113116.5 125 150 JA3-6,5x125-E16 31144113116.5 150 100 JA3-6,5x150-E16 31146113116.5 175 100 JA3-6,5x175-E16 31147113116.5 200 100 JA3-6,5x200-E16 31148113116.5 230 100 JA3-6,5x230-E16 31149113116.5 260 100 JA3-6,5x260-E16 31109113116.5 290 150 JA3-6,5x290-E16 3116211311Sealing washer E19, Ø 19 mm6.5 19 500 JA3-6,5x19-E19 31131123116.5 25 500 JA3-6,5x25-E19 31132123116.5 32 500 JA3-6,5x32-E19 31133123116.5 38 500 JA3-6,5x38-E19 31134123116.5 45 250 JA3-6,5x45-E19 31135123116.5 50 250 JA3-6,5x50-E19 31136123116.5 64 250 JA3-6,5x64-E19 31138123116.5 75 200 JA3-6,5x75-E19 31139123116.5 90 200 JA3-6,5x90-E19 31141123116.5 100 200 JA3-6,5x100-E19 31142123116.5 115 150 JA3-6,5x115-E19 31143123116.5 125 150 JA3-6,5x125-E19 31144123116.5 150 100 JA3-6,5x150-E19 31146123116.5 175 100 JA3-6,5x175-E19 31147123116.5 200 100 JA3-6,5x200-E19 31148123116.5 230 100 JA3-6,5x230-E19 31149123116.5 260 100 JA3-6,5x260-E19 3110912311
6.5 290 100 JA3-6,5x290-E19 3116212311Sealing washer E22, Ø 22 mm (see next page)
79
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s J A 3 / J Z 3
Sel
f-ta
ppin
g sc
rew
s
A 2 s t a i n l e s s s t e e l
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E22, Ø 22 mm6.5 19 500 JA3-6,5x19-E22 31131133116.5 25 500 JA3-6,5x25-E22 31132133116.5 32 200 JA3-6,5x32-E22 31133133116.5 38 200 JA3-6,5x38-E22 31134133116.5 45 250 JA3-6,5x45-E22 31135133116.5 50 250 JA3-6,5x50-E22 31136133116.5 64 200 JA3-6,5x64-E22 31138133116.5 75 150 JA3-6,5x75-E22 31139133116.5 90 150 JA3-6,5x90-E22 31141133116.5 100 150 JA3-6,5x100-E22 31142133116.5 115 100 JA3-6,5x115-E22 31143133116.5 125 100 JA3-6,5x125-E22 31144133116.5 150 100 JA3-6,5x150-E22 31146133116.5 175 100 JA3-6,5x175-E22 31147133116.5 200 100 JA3-6,5x200-E22 31148133116.5 230 50 JA3-6,5x230-E22 31149133116.5 260 100 JA3-6,5x260-E22 3110913311
6.5 290 100 JA3-6,5x290-E22 3116213311
EJOT®
Self-tapping screw JA3-6,5
J3
APPLICATION RANGE• For � xing pro� led steel sheets to timber substructure• For � xing sandwich panels to timber substructure• For � xing pro� led steel / aluminium sheet to � 2 mm steel
substructure• Side lap stitching of pro� led steel / aluminium sheet
APPROVALETA-10/0200Z-14.4-407Z-14.1-537
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-2-6,5 .................... page 58 Storm washers ........................................ page 85 Special screwgun DAM5 .......................... page 180
80
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - t a p p i n g s c r e w s J A 3 / J Z 3
Sel
f-ta
ppin
g sc
rew
s
A 2 s t a i n l e s s s t e e l
EJOT®
Self-tapping screw JZ3-6,3
J3
APPLICATION RANGE• For � xing pro� led steel sheets/sandwich panels
to steel substructure• For � xing steel / aluminium pro� led sheets
to aluminium substructures
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALETA-10/0200Z-14.4-407Z-14.1-537
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-6-5,5 .................... page 60 Self-drilling screw JT3-12-5,5 .................. page 62 Storm washers ........................................ page 85 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm6.3 19 500 JZ3-6,3x19-E16 31111113116.3 25 500 JZ3-6,3x25-E16 31112113116.3 32 500 JZ3-6,3x32-E16 31113113116.3 38 500 JZ3-6,3x38-E16 31114113116.3 50 250 JZ3-6,3x50-E16 31116113116.3 64 250 JZ3-6,3x64-E16 31118113116.3 80 200 JZ3-6,3x80-E16 31120113116.3 90 200 JZ3-6,3x90-E16 31121113116.3 100 200 JZ3-6,3x100-E16 31122113116.3 115 150 JZ3-6,3x115-E16 31123113116.3 125 150 JZ3-6,3x125-E16 31124113116.3 135 100 JZ3-6,3x135-E16 31125113116.3 150 100 JZ3-6,3x150-E16 31126113116.3 175 100 JZ3-6,3x175-E16 31127113116.3 200 100 JZ3-6,3x200-E16 31128113116.3 230 100 JZ3-6,3x230-E16 31129113116.3 270 100 JZ3-6,3x270-E16 3110611311Sealing washer E19, Ø 19 mm6.3 19 500 JZ3-6,3x19-E19 31111123116.3 25 500 JZ3-6,3x25-E19 31112123116.3 32 500 JZ3-6,3x32-E19 31113123116.3 38 500 JZ3-6,3x38-E19 31114123116.3 50 250 JZ3-6,3x50-E19 31116123116.3 64 250 JZ3-6,3x64-E19 31118123116.3 80 200 JZ3-6,3x80-E19 31120123116.3 90 200 JZ3-6,3x90-E19 31121123116.3 100 200 JZ3-6,3x100-E19 31122123116.3 115 150 JZ3-6,3x115-E19 31123123116.3 125 150 JZ3-6,3x125-E19 31124123116.3 135 100 JZ3-6,3x135-E19 31125123116.3 150 100 JZ3-6,3x150-E19 31126123116.3 175 100 JZ3-6,3x175-E19 31127123116.3 200 100 JZ3-6,3x200-E19 31128123116.3 230 100 JZ3-6,3x230-E19 31129123116.3 270 100 JZ3-6,3x270-E19 3110612311Sealing washer E22, Ø 22 mm (see next page)
81
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s J A 3 / J Z 3
Sel
f-ta
ppin
g sc
rew
s
A 2 s t a i n l e s s s t e e l
EJOT®
Self-tapping screw JZ3-6,3
J3
APPLICATION RANGE• For � xing pro� led steel sheets/sandwich panels
to steel substructure• For � xing steel/aluminium pro� led sheets
to aluminium substructures
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALETA-10/0200Z-14.4-407Z-14.1-537
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Self-drilling screw JT3-6-5,5 .................... page 60 Self-drilling screw JT3-12-5,5 .................. page 62 Storm washers ........................................ page 85 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E22, Ø 22 mm6.3 19 500 JZ3-6,3x19-E22 31111133116.3 25 500 JZ3-6,3x25-E22 31112133116.3 32 200 JZ3-6,3x32-E22 31113133116.3 38 200 JZ3-6,3x38-E22 31114133116.3 50 250 JZ3-6,3x50-E22 31116133116.3 64 200 JZ3-6,3x64-E22 31118133116.3 80 150 JZ3-6,3x80-E22 31120133116.3 90 150 JZ3-6,3x90-E22 31121133116.3 100 150 JZ3-6,3x100-E22 31122133116.3 115 100 JZ3-6,3x115-E22 31123133116.3 125 100 JZ3-6,3x125-E22 31124133116.3 135 100 JZ3-6,3x135-E22 31125133116.3 150 100 JZ3-6,3x150-E22 31126133116.3 175 100 JZ3-6,3x175-E22 31127133116.3 200 100 JZ3-6,3x200-E22 31128133116.3 230 50 JZ3-6,3x230-E22 3112913311
6.3 270 100 JZ3-6,3x270-E22 3110613311
82
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - t a p p i n g s c r e w s J A 1 / J Z 1A 5 s t a i n l e s s s t e e l
Sel
f-ta
ppin
g sc
rew
s
EJOT Corremaks®
Self-tapping screw JA1-6,5
J1
APPLICATION RANGE• Side lap stitching of pro� led steel sheets in highly
corosive environments• Fixing pro� led steel sheets to timber substructures in
highly corrosive environments
FEATURES• A5 stainless steel – 1.4529• Stainless steel sealing washer• Pre-assembled sealing washer• Highest corrosion protection class
APPROVALETA-10/0200
TECHNICAL DATADrive ........................................................hexagon A/F3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.5 22 0 - 9 500 JA1-6,5x22 31132003196.5 38 0 - 25 500 JA1-6,5x38 31134003196.5 64 0 - 51 250 JA1-6,5x64 31138003196.5 115 40 - 102 200 JA1-6,5x115 3114300319Sealing washer E16, Ø 16 mm6.5 22 0 - 6 500 JA1-6,5x22-E16 31132113196.5 38 0 - 22 500 JA1-6,5x38-E16 31134113196.5 64 0 - 48 250 JA1-6,5x64-E16 31138113196.5 115 40 - 99 150 JA1-6,5x115-E16 3114311319
EJOT Corremaks®
Self-tapping screw JZ1-6,3
J1
APPLICATION RANGE• Fixing pro� led steel sheets to steel substrate in highly
corrosive environments
FEATURES• A5 stainless steel – 1.4529• Stainless steel sealing washer• Pre-assembled sealing washer• Highest corrosion protection class
APPROVALETA-10/0200
TECHNICAL DATADrive ........................................................hexagon A/F3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
without sealing washer6.3 22 0 - 9 500 JZ1-6,3x22 3111200319Sealing washer E16, Ø 16 mm6.3 22 0 - 6 500 JZ1-6,3x22-E16 3111211319
83
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s J Z 7A 2 s t a i n l e s s s t e e l
Sel
f-ta
ppin
g sc
rew
s
EJOT CRONIMAKS®
Self-tapping screw JZ7-6,3
J7
APPLICATION RANGE• Fixing pro� led steel sheet / sandwich panels
to steel substrate up to S 355 (St 52)• Fixing pro� led steel sheet / sandwich panels to
stainless steel substrate (up to Rm = 700 N/mm²)
FEATURES• Approved A2 stainless steel screw for high-strength
steel substructures• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALETA-10/0200Z-14.4-407
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Storm washers ........................................ page 85 Special screwgun DAM5 .......................... page 180
Ømm
Length mm
Clamp thickness mm
PUPrice €/100 pcs.
Order description Part number
Sealing washer E16/2, Ø 16 mm6.3 22 0 - 6 500 JZ7-6,3x22-E16/2 32902117116.3 65 0 - 49 250 JZ7-6,3x65-E16/2 32906117116.3 85 20 - 69 200 JZ7-6,3x85-E16/2 32908117116.3 105 40 - 89 200 JZ7-6,3x105-E16/2 32910117116.3 125 60 - 109 150 JZ7-6,3x125-E16/2 32912117116.3 145 80 - 129 100 JZ7-6,3x145-E16/2 32914117116.3 165 100 - 149 100 JZ7-6,3x165-E16/2 32916117116.3 185 120 - 169 100 JZ7-6,3x185-E16/2 3291811711Sealing washer E19/3, Ø 19 mm6.3 22 0 - 6 500 JZ7-6,3x22-E19/3 32902127116.3 65 0 - 49 200 JZ7-6,3x65-E19/3 32906127116.3 85 20 - 69 200 JZ7-6,3x85-E19/3 32908127116.3 105 40 - 89 200 JZ7-6,3x105-E19/3 32910127116.3 125 60 - 109 150 JZ7-6,3x125-E19/3 32912127116.3 145 80 - 129 100 JZ7-6,3x145-E19/3 32914127116.3 165 100 - 149 100 JZ7-6,3x165-E19/3 32916127116.3 185 120 - 169 100 JZ7-6,3x185-E19/3 3291812711Sealing washer E22/3, Ø 22 mm6.3 22 0 - 6 500 JZ7-6,3x22-E22/3 32902137116.3 65 0 - 49 200 JZ7-6,3x65-E22/3 32906137116.3 85 20 - 69 150 JZ7-6,3x85-E22/3 32908137116.3 105 40 - 89 150 JZ7-6,3x105-E22/3 32910137116.3 125 60 - 109 100 JZ7-6,3x125-E22/3 32912137116.3 145 80 - 129 100 JZ7-6,3x145-E22/3 32914137116.3 165 100 - 149 100 JZ7-6,3x165-E22/3 3291613711
6.3 185 120 - 169 100 JZ7-6,3x185-E22/3 3291813711
84
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S e l f - t a p p i n g s c r e w sN o t e s
Sel
f-ta
ppin
g sc
rew
s
© Olaf Schuelke THE ADDRESS HOTEL, DUBAI Supplied by EJOT: EJOT® insulation support anchor DH
85
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S t o r m w a s h e r s
Sto
rm
was
hers
ORKAN storm washers by EJOT®
ADVANTAGES:• Increased installation reliability• High dimensional stability• Optimum load transmission
FEATURES• Optimised reinforcement flanges ensure high
instalaltion reliablity• Secure waterproofing• Available in aluminium self colour, stucco, and coloured• In combination with EJOT® self-drilling and self-tapping
screws a sophisticated fastening system• Patented Europe-wide
NOTEOnly use screws with 16mm washer diameter. For determination of the clamp thickness please take the storm washer into account with 3 mm.
ORKAN storm washer for crown � xing
NOTEFor crown� xing we generally recommend storm washers.
REQUIREMENTSEJOT® ORKAN storm washer have to ful� l multiple requirements.They utilise a consistent load distribution of the crown � xing of a trapezoidal pro� led sheets or sandwich elements. The pronounced reinforcement � anges of the EJOT® storm washers are a guarantee for high dimensional stability and consistent load transmission.As a so-called second insulation level the EJOT® storm washer permanently buffers the � xed size between upper substructure edge. The screw head and the crown of a sheet is often slightly convex or concave and in order to compensate these tolerances a soft closed-cell rubber is ideal. No bridging arises where humidity can enter the fastener shank and thus the inside of the building. The permanent compression required for the lasting watertightness of this cellular rubber is minimal and the deformation of a thin-walled trapezoidal pro� led sheet can thus be prevented during installation.
INSTALLATION RELIABILITYAn EJOT® storm washer also guarantees installation reliability. The installer always hits the middle of the crown after applying the storm washer which prevents scratching of the surface.It enables an increased clamping force on the component, without plastic deformation.The increased loads due to the use of EJOT® storm washers are documented in various building authorities test certi� cates (type statistics) of aluminium trapezoidal pro� les.
SELECTION AIDOur application engineering will gladly assist you in selecting the right choice of storm washer. We need the following three values in mm:• Crown width• Profile height• Valley width
FAX REPLYPlease fax the three values to the following fax number: +49 2752 908-731
Crown widthmm
Valley distancemm
Pro� le heightmm
86
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S t o r m w a s h e r s
Sto
rm
was
hers
EJOT® ORKAN storm washerTrapeze
APPLICATION RANGE• For crown fixing of trapezoidal profiled sheet • For crown � xing of sandwich panels
FEATURES• For trapezoidal profiles• Aluminium alloy self colour, coloured or stucco
CROSS REFERENCESelf-drilling screw JT3-2-6,5 .................... page 58 Self-drilling screw JT3-6-5,5 .................... page 60
Self-drilling screw JT3-12-5,5 .................. page 62
Self-tapping screw JA3-6,5 ...................... page 78 Self-tapping screw JZ3-6,3 ...................... page 80 Self-tapping screw JZ7-6,3 ...................... page 83
Storm washer width mm
Angle of inclina-
tion °
Crownwidth
mmPU
Price €/100
pcs.Order description Part number
Alu self colour20 34 19 500 Storm washer 20-34 alu self colour 304670011021 16 20 500 Storm washer 21-16 alu self colour 304660011021 25 20 500 Storm washer 21-25 alu self colour 305212500026 15 25 500 Storm washer 26-15 alu self colour 304690011026 27 25 500 Storm washer 26-27 alu self colour 304700011026 34 25 500 Storm washer 26-34 alu self colour 305263400031 31 30 500 Storm washer 31-31 alu self colour 305313200031 37 30 500 Storm washer 31-37 alu self colour 304590011032 25 31 500 Storm washer 32-25 alu self colour 305312400035 23 34 500 Storm washer 35-23 alu self colour 304610011036 40 35 500 Storm washer 36-40 alu self colour 305353800041 16 40 500 Storm washer 41-16 alu self colour 304620011041 32 40 500 Storm washer 41-32 alu self colour 304920011041 39 40 500 Storm washer 41-39 alu self colour 305413900053 36 52 400 Storm washer 53-36 alu self colour* 305533600055 32 54 400 Storm washer 55-32 alu self colour 3049500110Alu coloured20 34 19 500 Storm washer 20-34 alu** -21 16 20 500 Storm washer 21-16 alu** -21 25 20 500 Storm washer 21-25 alu** -26 15 25 500 Storm washer 26-15 alu** -26 27 25 500 Storm washer 26-27 alu** -26 34 25 500 Storm washer 26-34 alu** -31 31 30 500 Storm washer 31-31 alu** -31 37 30 500 Storm washer 31-37 alu** -32 25 31 500 Storm washer 32-25 alu** -35 23 34 500 Storm washer 35-23 alu** -36 40 35 500 Storm washer 36-40 alu** -41 16 40 500 Storm washer 41-16 alu** -41 32 40 500 Storm washer 41-32 alu** -41 39 40 500 Storm washer 41-39 alu** -53 36 52 400 Storm washer 53-36 alu** -55 32 54 400 Storm washer 55-32 alu** -Alu-stucco20 34 19 500 Storm washer 20-34 alu stucco 304670011921 16 20 500 Storm washer 21-16 alu stucco 304660011921 25 20 500 Storm washer 21-25 alu stucco -26 15 25 500 Storm washer 26-15 alu stucco 304690011926 27 25 500 Storm washer 26-27 alu stucco 304700011931 31 30 500 Storm washer 31-31 alu stucco -31 37 30 500 Storm washer 31-37 alu stucco 304590011932 25 31 500 Storm washer 32-25 alu stucco -35 23 34 500 Storm washer 35-23 alu stucco 304610011936 40 35 500 Storm washer 36-40 alu stucco 306364000041 16 40 500 Storm washer 41-16 alu stucco 304620011941 32 40 500 Storm washer 41-32 alu stucco 304920011941 39 40 500 Storm washer 41-39 alu stucco -53 36 52 400 Storm washer 53-36 alu stucco* 308533600055 32 54 400 Storm washer 55-32 alu stucco 3049500119
* Storm washer can be supplied with centrally located hole or in special shape with off-centre hole for crown corrugated pro� les
* add four-digit RAL reference.
87
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S t o r m w a s h e r s
Sto
rm
was
hers
Radius mm
for corrugated pro� le
Length mm
PUPrice
€/100 pcs.
Order description Part number
Alu self colour24 18/76 50 500 Storm washer W24 Alu self colour 304770011030 27/111 50 500 Storm washer W30 Alu self colour 305003000048 42/160 and 55/177 50 500 Storm washer W48 Alu self colour 3047400110Alu coloured24 18/76 50 500 Storm washer W24 Alu* -30 27/111 50 500 Storm washer W30 Alu* -48 42/160 and 55/177 50 500 Storm washer W48 Alu* -Alu-stucco24 18/76 50 500 Storm washer W24 Alu stucco 304770011930 27/111 50 500 Storm washer W30 Alu stucco 306003000048 42/160 and 55/177 50 500 Storm washer W48 Alu stucco 3060048000
* add four-digit RAL colour code.
EJOT® ORKAN storm washerCorrugated pro� le
Application Range• For crown fixing of corrugated sheet• For crown � xing of sandwich panels
FEATURES• For corrugated sheets• Aluminium alloy self colour, coloured or stucco
CROSS REFERENCESelf-drilling screw JT3-2-6,5 .................... page 58 Self-drilling screw JT3-6-5,5 .................... page 60
Self-drilling screw JT3-12-5,5 .................. page 62
Self-tapping screw JA3-6,5 ...................... page 78 Self-tapping screw JZ3-6,3 ...................... page 80 Self-tapping screw JZ7-6,3 ...................... page 83
ALUBEL
alubel 28 41 - 32
alubel 21 26 - 38
alubel 40 41 - 32
alubel 44 31 - 31
Alutech Dach 26 - 27
Aluform
Aluform 20/125 41 - 32
Aluform 29/124 20 - 34
Aluform 30/153 26 - 34
Aluform 40/167 35 - 23
Aluform 42/250 31 - 31
Aluform 45/150 26 - 27
Aluform 45/200 41 - 24
Alutherm DT 900 26 - 27
Alutherm DT 1000 31 - 31
Corrugated sheet 18/76 W 24
Corrugated sheet 35/137 W 43
Corrugated sheet 55/177 W 48
ARCELOR
AL 34/207 41 - 39
A 35/207 35 - 47
B 35/207 41 - 16
39/333 T 26 - 27
AL 40/183 41 - 16
A 40/183 41 - 24
AL 42/333 S 31 - 21
ARCELOR
44/180 53 - 36
AL 45/150 26 - 27
50/262.5 46 - 43
85/280 41 - 39
100/275 41 - 24
105/345 41 - 24
106/250 41 - 16
Ondatherm 1001 TS 26 - 27
Onda� bre 3005 T 26 - 27
Agratherm 1001 TS 26 - 27
Corrugated sheet 18/76 W24
BIEBER
20/125 41 - 32
30/262K 41 - 44
35/207 41 - 32
40/183/183 S 41 - 16
50/250 41 - 39
50/262 46 - 43
58/315K 53 - 36
70/200 53 - 18
80/307 41 - 32
89/305 41 - 32
100/275 41 - 24
106/250 41 - 16
110/333 41 - 16
EJOT® ORKAN storm washerSelection aid
Manufacturer Pro� le descriptionEJOT®
storm washerManufacturer Pro� le description
EJOT®
storm washer
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesother RAL colours and special colours on request
88
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S t o r m w a s h e r s
Sto
rm
was
hers
S e l e c t i o n a i d
Dansk Pro� ltechnik
DP 20/35 36 - 40
DP 20/65 26 - 36
DP 20/100 26 - 42
DP 35/115 41 - 33
DP Sinus 18/76 W 24
DP Sinus 35/143 W 30
DP Sinus Variant 35/143 W 30
BRUCHADP72/82/102/122/142/162 26 - 15
DP-F 26 - 34
DS Staalpro� l
DS 20/115 26 - 34
DS 35/190 41 - 39
DS 35/206 36 - 40
DS Sinus 35/143 W 30
SISCOROOF 4G 21 - 16
SISCOTEC ROOF 4G 21 - 16
FINISH PROFILES
Dakpro� el 18 - 76 W 24
Dakpro� el 42 - 960 W 48
Dakpro� el 20 - 1090 31 - 47
Dakpro� el 35 - 1000 41 - 24
Dakpro� el 40 - 915 41 - 16
Dakpro� el 50 - 1000 55 - 32
Dakpro� el 58 - 945 KD 53 - 36
Dakpro� el 70R - 800 53 - 18
FISCHER
35/207 41 - 32
40/183 41 - 16
50/250 55 - 32
85/280 41 - 32
100/275 41 - 24
Sinus 18 W 24
Sinus 27 W 30
Sinus 42 W 48
DL 70;80;100;120;140;160
41 - 32
20/220 41 - 46
Friedrich von Lien AGWeckmann
W-20/990 26 - 34
W-20/1100 26 - 50
W-45R/900 41 - 24
W-45ER/1000 31 - 43
W-155/840 41 - 24
W-1/1064 W 24
ITALPANNELLI Penta 40 21 - 16
Joriside
JI 33.250.1000 23 - 33
JI 45.333.1000 26 - 27
JI 35.207.1035 41 - 39
JI 40.183.915 41 - 16
JI 50.250.1000 55 - 32
JI 58.317.945 53 - 42
JI Roof 1000 26 - 27
JI Ecopaneel 1000 23 - 33
KINGSPANKS 1000 RW 32 - 25
KS 1000 FF 23 - 33
Klinger & Partner Pro� lvertrieb GmbH
35.207.1035 41 - 39
39.333.1000 26 - 34
KLÖCKNER
KAS AL-20/125 A 41 - 32
KAS AL-30/153 A 26 - 27
KAS-35/207 41 - 32
KAS AL-40/167 A 35 - 23
KAS-40/183 41 - 16
KAS AL-45/200 A 41 - 24
KAS-50/250 55 - 32
KAS-85/280 41 - 39
Manufacturer Pro� le descriptionEJOT®
storm washerManufacturer Pro� le description
EJOT®
storm washer
KLÖCKNER
KAS-89/305 41 - 32
KAS -18/76 W 24
KAS -42/160 W 48
KAS -55/177 W 48
KAS -D 65 - 115 36 - 40
KAS -D 68 21 - 16
KAS -D 80 41 - 32
KAS -D 62 - 142 26 - 15
Lattonedil
Isocopre 20 - 34
Eurocinque 21 - 16
Eurocopre 20 - 34
Laukien
35 - 207 41 - 32
22 - 214 41 - 39
20 - 75 26 - 34
45 - 333 S 26 - 27
40 - 100 31 - 31
50 - 250 41 - 39
18 / 76 W 24
27 / 111 W 30
42 / 160 W 48
55 / 177 W 48
LINDAB
LP 20 26 - 34
LP 35 41 - 32
LP 1100 26 - 45
Sinus 18 W 24
Luxmetall
LM40 250 1000 26 - 27
LM19 156 1094 26 - 45
LM 27-111-1000 W 30
Maas
20-75 26 - 34
22-214 41 - 39
35-207 41 - 32
40-100 31 - 31
45-150 26 - 27
45-333 S 26 - 27
Corrugated sheet 18/76 W24
Corrugated sheet 27/111 W30
Corrugated sheet 55/177 W48
METECNO
G4 21 - 16
Hipertec Dach 21 - 16
Hipertec Dach Sound 21 - 16
Toproof DG 20 - 34
SISCO 21 - 16
MONTANA
SP 20 26 - 34
SP 26 41 - 24
SP 30 41 - 46
SP 35 41 - 32
SP 40 41 - 16
SP 41 41 - 24
SP 44 31 - 22
SP 45 41 - 32
SP 59 36 - 26
SP 80 41 - 16
MTD TL 65 35 - 23
MTD TL 85 35 - 23
MTD TL 105 35 - 23
MTD TL 125 35 - 23
MTD TL 145 35 - 23
SP 18/1064 W 24
SP 27/1000 W 30
SP 42/960 W 48
M-Pro� l KP 36 - 40
89
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S t o r m w a s h e r s
Sto
rm
was
hers
S e l e c t i o n a i d
Manufacturer Pro� le descriptionEJOT®
storm washerManufacturer Pro� le description
EJOT®
storm washer
MÜNKER
M 20/220 41 - 39
M 35/207 41 - 39
M 40/183 41 - 16
M 40/333 26 - 34
M 40KD/333 26 - 27
M 50/250 55 - 32
M 85/280 41 - 39
M 100/275 41 - 24
M 150/280 41 - 24
M 40/333 26 - 34
O Metall
20,125/8 41 - 32
20,136/8 31 - 45
25,280/3 41 - 16
25,268/4 26 - 38
30,207/5 36 - 26
30,153/7 26 - 34
35,207/5 41 - 39
40,183/5 41 - 16
40,250/4 26 - 27
45,150/6 26 - 27
45,333/3 26 - 27
50,250/4 55 - 32
50,262.5/4 46 - 43
Corrugated sheet 18/76 W 24
Corrugated sheet 55.177 W48
Corrugated sheet 27.111 W30
PLANNJA
Plannja 19 26 - 45
Plannja 20-102 26 - 38
Plannja 35 41 - 32
Sinus 18 W24
Sinus 51 W48
Plannja 20 36 - 40
Plannja 60 41 - 16
Plannja 30 31 - 37
Plannja 45 41 - 39
PROGE
20/154 26 - 34
26/143 41 - 32
30/207 35 - 47
30/220 41 - 44
30 KD 41 - 44
35/207 41 - 39
40/183 41 - 16
45/150 41 - 32
45/333 32 - 25
50/250 55 - 32
58 KD 53 - 42
59/225 36 - 26
70/200 53 - 18
80/277 41 - 16
85/280 41 - 39
90/305 41 - 32
100/275 41 - 24
105/345 41 - 24
106/250 41 - 16
Corrugated sheet 18/76 W 24
Corrugated sheet 27/111 W 30
Corrugated sheet 42/160 W 48
Corrugated sheet 55/177 W 48
ROMAKOWSKI D62; D82; D102; D122; D142 26 - 15
SAB19(KD)/1050 26 - 50
35R/1035 41 - 32
SAB
40R/915 41 - 16
50R/1000 55 - 32
70R/800 53 - 18
85R/1120 41 - 39
89R/915 41 - 32
100R/825 41 - 24
30KD/1050 41 - 44
45KD/1000 31 - 22
58KD/945 53 - 36
D 65-75-95-115-135 36 - 40
D 135.1000 TL 36 - 40
18 / 988 W 24
42 / 960 W 48
27 / 1000 W 24
SALZGITTER
PS 35/207 41 - 32
PS 40/183 41 - 16
PS 50/250 55 - 32
PS 85/280 41 - 39
PS 100/275 41 -24
SIP D 41 - 32
SIEGMETALL
CB 18/76 W 24
CB 35/207 35 - 47
40/183 41 - 16
40/333 26 - 27
50/250 55 - 32
CB 75/305 41 - 39
85/280 41 - 32
100/275 41 - 16
ThyssenKrupp Steel Europe AG
Hoesch Thermodach 41 - 32
T 35.1 41 - 39
T 40.1 41 - 16
T 50.1 55 - 32
T 85.1 41 - 32
T 100.1 41 - 24
T 106.1 41 - 16
WP 18/76 W 24
WP 42/160 W 48
WP 27/100 W 30
TRIMO SNV 26 - 27
Wurzer Pro� liertechnik GmbH
WU 20/125 41 - 32
WU 30/200 20 - 34
WU 30D/207 35 - 47
WU 30W/207 35 - 47
WU 35/207 41 - 32
WU 40/183 41 - 16
WU 45/333 26 -27
WU 50/250 55 - 32
WU 80/307 41 - 32
WU 100/275 41 - 24
WU 18/76 W 24
WU 27/111 W 30
WU 55/177 W 48
plusdach DL 41 - 32 steel
Ter 21 - 16
Corrugated sheet 42/160 W48
30,200/5 21 - 30
39,333/3 31 - 31
39/333 26 - 34
41/193.5 41 - 24
Not listed pro� les upon request!
90
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
EJOT®
Self-tapping screw BS-R-6,3
J2
APPLICATION RANGE• For � xing sandwich panels to concrete
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
TECHNICAL DATADrive ............................................................ hexagon A/F8Embedment depth � ............................................... 30 mmHole depth � .......................................................... 45 mm
NOTENominal drill diameter 5.0 mm
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer6.3 35 1000 BS-R-6,3x35 56630355126.3 45 500 BS-R-6,3x45 56630455126.3 100 250 BS-R-6,3x100 56631005126.3 120 200 BS-R-6,3x120 56631205126.3 140 200 BS-R-6,3x140 56631405126.3 160 200 BS-R-6,3x160 56631605126.3 180 200 BS-R-6,3x180 56631805126.3 200 150 BS-R-6,3x200 56632005126.3 220 150 BS-R-6,3x220 56632205126.3 240 150 BS-R-6,3x240 5663240512V16 sealing washer, Ø 16 mm6.3 35 1000 BS-R-6,3x35-V16 -6.3 45 500 BS-R-6,3x45-V16 -6.3 100 250 BS-R-6,3x100-V16 -6.3 120 200 BS-R-6,3x120-V16 -6.3 140 200 BS-R-6,3x140-V16 -6.3 160 200 BS-R-6,3x160-V16 -6.3 180 200 BS-R-6,3x180-V16 -6.3 200 150 BS-R-6,3x200-V16 -6.3 220 150 BS-R-6,3x220-V16 -
6.3 240 150 BS-R-6,3x240-V16 -Order information: Other sealing washers upon request
91
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
EJOT®
Self-tapping screw JA3-FR-4,9with truss head
APPLICATION RANGE• For fixing steel / aluminium pro� led sheets
to timber substructure• For � xing steel / aluminium pro� led sheets
to aluminium substructure � 2mm
FEATURES• A2 stainless steel• Stainless steel sealing washer• Truss head and sealing washer self colour or coloured• Pre-assembled sealing washer• Thread according to DIN 7998
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
FR-tool ................................................... page 187 Special screwgun DAM5 .......................... page 180
EJOT®
Self-tapping screw JA3-LT-4,9with pan head
APPLICATION RANGE• For � xing metal pro� les to timber substructure• For � xing metal pro� les to aluminium
substructure � 2mm
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T20
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.9 38 500 JA3-FR-4,9x38 32135003114.9 64 500 JA3-FR-4,9x64 3213800311Sealing washer self colour E14, Ø 14 mm4.9 38 500 JA3-FR-4,9x38-E14 32135093114.9 64 250 JA3-FR-4,9x64-E14 3213809311Sealing washer E14, Ø 14 mm, coloured4.9 38 500 JA3-FR-4,9x38-E14*4.9 64 250 JA3-FR-4,9x64-E14** add four-digit RAL colour code.
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.9 25 1,000 JA3-LT-4,9x25 32332003124.9 38 1,000 JA3-LT-4,9x38 5000638300Sealing washer self colour E14, Ø 14 mm4.9 25 500 JA3-LT-4,9x25-E14 32332093124.9 38 500 JA3-LT-4,9x38-E14 3233409312Sealing washer E14, Ø 14 mm, coloured4.9 25 500 JA3-LT-4,9x25-E14*4.9 38 500 JA3-LT-4,9x38-E14** add four-digit RAL colour code.
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesOther RAL colours and special colours on request
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesOther RAL colours and special colours on request
92
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
EJOT®
Self-tapping screw JA3-ZT-6,5with � at head
APPLICATION RANGE• For � xing metal pro� les to timber substructure• For � xing metal pro� les to aluminium substructure
� 3 mm and steel substructure � 2 mm
FEATURES• A2 stainless steel• With flat head• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T30
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
EJOT®
Self-tapping screw JA3-S-6,5with countersunk head
APPLICATION RANGE• For � xing metal pro� les to timber substructure• For � xing metal pro� les to aluminium substructure
� 3 mm and steel substructure � 2 mm
FEATURES• A2 stainless steel• with countersunk head
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T30
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
6.5 35 500 JA3-S-6,5x35 3029800311
6.5 95 200 JA3-S-6,5x95 3029300311
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E14, Ø 14 mm6.5 50 250 JA3-ZT-6,5x50-E14 3123083311
6.5 80 200 JA3-ZT-6,5x80-E14 3124083311
93
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
EJOT®
Repair screw JB3-7,2
J3
APPLICATION RANGE• For covering faulty drill holes
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrive ....................................................... hexagon A/F 3/8“
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E16, Ø 16 mm7.2 19 500 JB3-7,2x19-E16 3189111311Sealing washer E22, Ø 22 mm7.2 19 500 JB3-7,2x19-E22 3189113311
7.2 25 500 JB3-7,2x25-E22 3189213311
EJOT®
Self-tapping screw JB3-ZT-6,3with � at head
APPLICATION RANGE• For fastening to steel substructures with
limited accessibility
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T30
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer6.3 19 500 JB3-ZT-6,3x19 31221003196.3 25 500 JB3-ZT-6,3x25 3020100311Sealing washer E14, Ø 14 mm6.3 25 500 JB3-ZT-6,3x25-E14 3120183311Sealing washer E16, Ø 16 mm6.3 25 500 JB3-ZT-6,3x25-E16 3120111311
94
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
EJOT®
Self-tapping screw JZ3-S-6,3with countersunk head
APPLICATION RANGE• For fixing metal pro� les and timber
to steel substructure• For � xing metal pro� les and timber
to aluminium substructure
FEATURES• A2 stainless steel
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T30
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
EJOT®
Self-tapping screw JZ3-ZT-6,3with � at head
APPLICATION RANGE• For fixing metal pro� les and facade panels
to steel substructure• For � xing metal pro� les and facade panels
to aluminium substructure
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T30
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
6.3 19 1,000 JZ3-S-6,3x19 30294003116.3 25 500 JZ3-S-6,3x25 30295003116.3 35 500 JZ3-S-6,3x35 31217003016.3 64 250 JZ3-S-6,3x64 3029600311
6.3 90 200 JZ3-S-6,3x90 3029700311
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer6.3 19 500 JZ3-ZT-6,3x19 3027100311Sealing washer E14, Ø 14 mm6.3 19 500 JZ3-ZT-6,3x19-E14 3127183311Sealing washer E16, Ø 16 mm6.3 19 500 JZ3-ZT-6,3x19-E16 3127111311
95
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
S e l f - t a p p i n g s c r e w s
EJOT®
Self-tapping screw JZ3-8,0
J3
APPLICATION RANGE• Fixing of pro� led steel sheet to steel substructures
under high static stress• Fixing of steel / aluminium pro� led sheets
to aluminium substructures
FEATURES• A2 stainless steel• Stainless steel sealing washer• Pre-assembled sealing washer
APPROVALETA-10/0200
TECHNICAL DATADrive .......................................................... hexagon A/F13
CROSS REFERENCEAccessories ............................................ page 191
Special screwgun DAM5 .......................... page 180
EJOT®
Self-tapping screw Duro PT
APPLICATION RANGE• Concealed fixing of agraffes to HPL facade panels
(HPL = High Pressure Laminate)• Concealed � xing of anchor rails to substructures
FEATURES• Truss head• A4 stainless steel
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T30Hole depth � ......................................................... 5.5 mmHole depth � ......................................................... 7.5 mmHole depth � ....................................................... 10.5 mm
NOTEMax. installation torque 4Nm
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
Sealing washer E22, Ø 22 mm8 25 250 JZ3-8x25-E22 31312533118 32 250 JZ3-8x32-E22 31313533118 38 250 JZ3-8x38-E22 31314533118 64 150 JZ3-8x64-E22 31318533118 100 100 JZ3-8x100-E22 31322533118 125 100 JZ3-8x125-E22 31324533118 150 100 JZ3-8x150-E22 3131553311
8 200 50 JZ3-8x200-E22 3132853311
Ømm
Length mm
Drill hole Ø mm
clamping thickness
mmPU
Price € / 100
pcs.Order description Part number
6.0 9.5 * * 1000 Duro PT S60x9,5 45101163306.0 11.5 * * 1000 Duro PT S60x11,5 45101173306.0 14.5 * * 1000 Duro PT S60x14,5 4510118330
* Hole diameter and installation depth depend on the appearance of the facade panel. Consultation with the EJOT service team required.
96
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S p e c i a l s c r e w sN o t e s
Spe
cial
sc
rew
s
© A. Svinnset NEW OPERA, OSLO, NORWAYSupplied by EJOT: EJOT® SUPER-SAPHIR Self-drilling screw JT3, JA3 Self-tapping screw
97
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
C h i p b o a r d s c r e w sS p e c i a l s c r e w s
C h i p b o a r d s c r e w s
EJOT®
Chip board screw SH2-5,0with countersunk head
APPLICATION RANGE• For direct fastening to timber substructure
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T20
CROSS REFERENCEAccessories ............................................ page 191
EJOT® Chip board screw SH3-5,0with countersunk head
APPLICATION RANGE• For direct fastening to timber substructure
FEATURES• A2 stainless steel
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T20
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
5.0 35 500 SH2-5,0x35 2010464609
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
5.0 35 500 SH3-5,0x35 3195035330
98
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
C h i p b o a r d s c r e w s
EJOT®
Chip board screw SH3-S-5,0with countersunk head
APPLICATION RANGE• Fastening of wood cladding to timber substructure
FEATURES• A2 stainless steel• Countersunk head
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T25
CROSS REFERENCEAccessories ............................................ page 191
EJOT®
Chip board screw SH3-S-4,0with countersunk head
APPLICATION RANGE• Fastening of wood cladding to timber substructure
FEATURES• A2 stainless steel• Countersunk head
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T20
CROSS REFERENCEAccessories ............................................ page 191
EJOT®
Chip board screw SH3-S-4,5with countersunk head
APPLICATION RANGE• Fastening of wood cladding to timber substructure
FEATURES• A2 stainless steel• Countersunk head
TECHNICAL DATADrive ............................................ Hexalobular / TORX® T20
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
5.0 60 500 SH3-S-5,0x60 31950603495.0 70 500 SH3-S-5,0x70 3195070349
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
4.0 45 500 SH3-S-4,0x45 3194045349
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
4.5 55 500 SH3-S-4,5x55 3194555349
99
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
P T ® t y p e D G s c r e w s
EJOT PT® screw type DG 40-Zpan head with dog point / WN1552
APPLICATION RANGE• Aluminium screw boss• Thin-walled aluminium components
FEATURES• A4 stainless steel• Stainless steel sealing washer• For thread geometries optimised for aluminium
TECHNICAL DATAThread ................................................................... DG 40Drive .............................................hexalobular / TORX® T25
EJOT PT® screwtype DG 50-Z pan head with dog point / WN1552
APPLICATION RANGE• Aluminium screw boss• Thin-walled aluminium components
FEATURES• A4 stainless steel• Stainless steel sealing washer• For thread geometries optimised for aluminium
TECHNICAL DATAThread ................................................................... DG 50Drive .............................................hexalobular / TORX® T25
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer4.0 13 9 1,000 DG-40x13-Z 25901663404.0 19 15 1,000 DG-40x19-Z 2590167340with sealing washer E114.0 13 7 1,000 DG-40x13-Z-E11 25714663404.0 19 13 1,000 DG-40x19-Z-E11 2571467340
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
without sealing washer5.0 25 19 1,000 DG-50x25-Z 2590168340with sealing washer E115.0 25 16 1,000 DG-50x25-Z-E11 2571468340
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
5.5 42 35 DG-55x42-C 2590228320
EJOT PT® screwtype DG 55-Cpan head with point / WN1542
APPLICATION RANGE• Clamped joint in a u-shaped pro� le
FEATURES• A2 stainless steel• For thread geometries optimised for aluminium
TECHNICAL DATADrive ...................................................... PH2 cross-recess
100
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S p e c i a l s c r e w s
Spe
cial
sc
rew
s
P T ® t y p e D G s c r e w s
EJOT PT® self-drilling screwtype DG 50
pan head with drill point
APPLICATION RANGE• Direct fastening of T-bars to aluminium post and rail
designs• Fastening of additional pro� les, e.g. connecting pro� les,
expansion joints etc.
FEATURES• A2 stainless steel• For thread geometries optimised for aluminium
TECHNICAL DATADrilling capacity ................................................ bis 2,5 mmThread ................................................................... DG 50Drive .............................................hexalobular / TORX® T25
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
5.0 16 8 1,000 Self-drilling screw DG-50x16 7381108300
Ømm
Length mm
Clamp thickness mm
PUPrice €/
100 pcs.Order description Part number
4.0 16 10 1,000 Self-drilling screw DG-40x16 73821373004.0 25 19 1,000 Self-drilling screw DG-40x25 7382138300
EJOT PT® self-drilling screwtype DG 40
countersunk head with drill point / WN1543
APPLICATION RANGE• Fastening of metal � ttings to aluminium
FEATURES• A2 stainless steel• For thread geometries optimised for aluminium
TECHNICAL DATADrilling capacity ............................................. max. 2,5 mmHead diameter ....................................................... 7,5 mmThread ................................................................... DG 40Drive ...................................................... PH2 cross-recess
101
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S p e c i a l s c r e w sN o t e s
Spe
cial
sc
rew
s
PUMAVISION HEADQUARTERS, HERZOGENAURACH, GERMANY © rr-fotoreporterSupplied by EJOT: EJOT® ETICS anchors
102
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
R i v e tR
ivet
s
EJOT®
Blind rivet Al/E-4,8
APPLICATION RANGE• For side lap stitching of pro� led sheet
FEATURES• Rivet body made of aluminium (Al)• Mandrel made of stainless steel (E)• Captive locked
APPROVALZ-14.1-4
CROSS REFERENCEElectric riveting tool ................................. page 172
EJOT®
Blind rivet Al/V-4,8
APPLICATION RANGE• For side lap stitching of pro� led sheet
FEATURES• Rivet body made of aluminium (Al)• Zinc-plated steel (V) mandrel• Captive locked
APPROVALZ-14.1-4
CROSS REFERENCEElectric riveting tool ................................. page 172
EJOT®
Blind rivet K14-AI/E
APPLICATION RANGE• For � xing steel and aluminium substructures• To form � oating points on aluminium substructure
FEATURES• Rivet body made of aluminium (Al)• Mandrel made of stainless steel (E)• Captive locked
APPROVALZ-14.1-4
CROSS REFERENCEElectric riveting tool ................................. page 172
Ømm
Length mm
Drill hole
Ø mm
Clamping-range mm
PUPrice €/100 pcs.
Order description Part number
4.0 10.0 4.1 2.0 - 6.0 1,000 Blind rivet AL/E-4,0x10,0 93511150004.8 10.0 5.1 0.5 - 6.5 1,000 Blind rivet AL/E-4,8x10,0 93511210004.8 15.0 5.1 4.5 - 11.0 1,000 Blind rivet AL/E-4,8x15,0 9351124000
4.8 25.0 5.1 11.0 - 19.5 1,000 Blind rivet AL/E-4,8x25,0 9351130000
Ømm
Length mm
Drill hole
Ø mm
Clamping-range mm
PUPrice €/100 pcs.
Order description Part number
4.8 10.0 5.1 0.5 - 6.5 1,000 Blind rivet AL/V-4,8x10,0 9350120001
4.8 15.0 5.1 4.5 - 11.0 1,000 Blind rivet AL/V-4,8x15,0 9351122000
Ømm
Length mm
Drill hole
Ø mm
Clamping-range mm
PUPrice
€/100 pcs.
Order description Part number
5.0 8.0 5.1 1.0 - 3.5 1,000 Blind rivet K14-AL/E-5,0x8,0 93502010005.0 10.0 5.1 3.5 - 5.0 1,000 Blind rivet K14-AL/E-5,0x10 93502020005.0 12.0 5.1 4.0 - 6.5 1,000 Blind rivet K14-AL/E-5,0x12,0 93502030005.0 14.0 5.1 6.5 - 8.0 1,000 Blind rivet K14-AL/E-5,0x14,0 93502130005.0 16.0 5.1 8.0 - 9.5 1,000 Blind rivet K14-AL/E-5,0x16,0 9350239000
5.0 18.0 5.1 8.5 - 11.0 1,000 Blind rivet K14-AL/E-5,0x18,0 9350207000
103
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
R i v e t
Riv
ets
Ømm
Length mm
Drill hole
Ø mm
Clamping-range mm
PUPrice
€/100 pcs.
Order description Part number
4.8 8.3 4.9 0.5 - 3.2 1,000 Closed-end rivet AL/E-4,8x8,3 93501020014.8 10.0 4.9 3.2 - 4.8 1,000 Closed-end rivet AL/E-4,8x10 93501080014.8 11.5 4.9 4.8 - 6.4 1,000 Closed-end rivet AL/E-4,8x11,5 93501030014.8 13.0 4.9 6.4 - 7.9 1,000 Closed-end rivet AL/E-4,8x13,0 93501060014.8 14.5 4.9 7.9 - 9.5 1,000 Closed-end rivet AL/E-4,8x14,5 93501090014.8 18.0 4.9 9.5 - 12.7 1,000 Closed end rivet AL/E-4,8x18,0 9350110001
4.8 22.0 4.9 12.7 - 15.9 1,000 Closed-end rivet AL/E-4,8x22,0 9350107001
Ømm
Length mm
Drill hole
Ø mm
Clamping-range mm
PUPrice
€/100 pcs.
Order description Part number
4.8 8.3 4.9 - 3.2 1,000 Closed-end rivet AL/V-4,8x8,3 93501130014.8 10.0 4.9 3.2 -4.8 1,000 Closed-end rivet AL/V-4,8x10,0 93501120014.8 11.5 4.9 4.8 - 6.4 1,000 Becherblindniet AL/V-4,8x11,5 93501010014.8 13.0 4.9 6.4 - 7.9 1,000 Closed-end rivet AL/V-4,8x13,0 9350104001
4.8 14.5 4.9 7.9 - 9.5 1,000 Closed-end rivet AL/V-4,8x14,5 9350105001
EJOT®
Closed-end rivet Al/E-4,8
APPLICATION RANGE• For side lap stitching of pro� led sheet
FEATURES• Rivet body made of aluminium (Al)• Mandrel made of stainless steel (E)• Captive locked
APPROVALZ-14.1-4
CROSS REFERENCEElectric riveting tool ................................. page 172
EJOT®
Closed-end rivet Al/V-4,8
APPLICATION RANGE• For side lap stitching of pro� led sheet
FEATURES• Rivet body made of aluminium (Al)• Zinc-plated steel (V) mandrel• Captive locked
APPROVALZ-14.1-4
CROSS REFERENCEElectric riveting tool ................................. page 172
104
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
R i v e tR
ivet
s
EJOT® Bulb-tite rivet
APPLICATION RANGE• For side lap stitching of metal and pro� led plastic sheets
FEATURES• Body made of aluminium (Al) with neoprene sealing• Mandrel made of aluminium (Al)• Captive locked
APPROVALZ-14.1-4
CROSS REFERENCEElectric riveting tool ................................. page 172
EJOT®
Drive rivet Al/E-4,8
APPLICATION RANGE• For use in metal, masonry and concrete
FEATURES• Rivet body made of aluminium (Al)• Mandrel made of stainless steel (E)
Ømm
Length mm
Drill hole
Ø mm
Clamping-range mm
PUPrice €/
100 pcs.
Order description Part number
5.2 17.5 5.4 1.3 - 4.8 1,000 Bulbtite rivet -5,2x17,5 93502340005.2 19.1 5.4 1.5 - 6.4 1,000 Bulbtite rivet-5,2x19,1 93502040015.2 22.2 5.4 4.8 - 9.5 1,000 Bulbtite rivet-5,2x22,2 93502300005.2 25.4 5.4 7.9 - 12.7 500 Bulbtite rivet-5,2x25,4 93502310005.2 28.6 5.4 11.1 - 15.9 500 Bulbtite rivet-5,2x28,6 9350233000
5.2 31.8 5.4 14.3 - 19.1 500 Bulbtite rivet-5,2x31,8 9350232000
Ømm
Length mm
Drill hole
Ø mmPU
Price €/100 pcs.
Order description Part number
4.8 15.3 5 1,000 Drive rivet AL/E-4.8x15.3 85516001304.8 25.4 5 1,000 Drive rivet AL/E-4.8x25.4 85526001304.8 35.0 5 500 Drive rivet AL/E-4.8x35.0 8553600130
Other designs on request.
105
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
F a s t e n i n g S y s t e m s
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
f o r S o l a r I n s t a l l a t i o n s
Set screw DIN 913 M10 x Lg A2
Lock nut DIN 985 M10
Plain washer M10
Hex nut M10
Sealing washer E16
EJOT® ORKAN storm washer
EJOT® Self-tapping screw JZ3 - 8,0 x L
EJOT® Self-tapping screw JA3 - 8,0 x L
FZD A2 sealing washer
Drive A/F 5
EJOT® Solar Fastening System
APPLICATION RANGE• For fastening elevated solar and photovoltaic installations
FEATURES• A2 stainless steel
APPROVALZ-14.4-532
ADVANTAGES:• Short delivery times• Flexibility in case of special requests• Expert advise• High product quality through strict quality control• Quick retrofitting on existing roofs• No additional holes in the roof cladding• Use of proven sealing systems• No special assembly tools necessary• Extremely secure attachment due to direct fastening into
the substructure• Building authorities approved fastening system• Project related structural pre-analysis, free of charge
106
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
F a s t e n i n g S y s t e m s
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
f o r S o l a r I n s t a l l a t i o n s
EJOT® Solar Fastening System Product Key:
Example:
JZ3-SB-DxL/LG-E16 + storm washer or FZD
D = diameter of screw (lower part)L = length of screw (lower part)Lg = length of set screw (upper part)Typ JZ3 = suitable for steel substructuresTyp JA3 = suitable for wood substructures
Standard Product Rangefor Ø 8,0-mm versions
NOTEFurther lengths on request!
NOTEFor more information please see our brochure EJOT® Solar Fastening Systems, which you can also download at our webpage www.ejot.com
The EJOT service team will gladly assist you. Phone: +49 2752 908-0
TABLE OF CONTENTS (EXCERPT)EJOT® Solar Fastening SystemEJOT® Solar Fastening System concreteEJOT® Flat Roof Solar Fastening SystemEJOT® Solar Fastening System FD
Version JZ3-SB- JA3-SB-For substructure steel woodMaterial A2 stainless steel A2 stainless steelDrive A/F 5 A/F 5
Threaded partM10 x 50 M10 x 50M10 x 70 M10 x 70
Sealing systemsSealing washer E16/2 + Storm Washer Sealing washer E16/2 + Storm WasherSealing washer FZD A2 Sealing washer FZD A2
Ø D [mm] 8.0 8.0
Screw length L [mm]
64 8080 100100 130125 150150 180160 200200240280
L Lg
D
Bre
ite
Winkel S
tift øE16
Wid
th
Pin
Angle
107
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
F a s t e n i n g S y s t e m s
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
f o r S o l a r I n s t a l l a t i o n s
EJOT® Solar Fastening System JZ3-SB-with JZ3 thread for steel substrate
FEATURES• A2 stainless steel
APPROVALZ-14.4-532
SEAL TYPE I• Sealing washer E16/2 + ORKAN storm washer
APPLICATION RANGE TYPE I• Trapezoidal pro� le (metal)• Corrugated pro� le sheet (metal)• Sandwich panel
SEAL TYPE II• Pre-assembled FZD sealing washer
+ A2 stainless steel spreader washer
APPLICATION RANGE TYPE II• Corrugated pro� le sheet• Fibre cement pro� les
EJOT® Solar Fastening System JA3-SB-with JA3 thread for timber substructure
FEATURES• A2 stainless steel
APPROVALZ-14.4-532
SEAL TYPE I• Sealing washer E16/2 + ORKAN storm washer
APPLICATION RANGE TYPE I• Trapezoidal pro� le (metal)• Corrugated pro� le sheet (metal)• Sandwich panel
SEAL TYPE II• Pre-assembled FZD sealing washer
+ A2 stainless steel spreader washer
APPLICATION RANGE TYPE II• Corrugated pro� le sheet• Fibre cement pro� les
TYPE I
TYPE II
TYPE I
TYPE II
108
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
F a s t e n i n g S y s t e m s f o r S o l a r I n s t a l l a t i o n s – N o t e s
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
© Colexon Energy AG WORLD'S LARGEST ROOF SOLAR POWER STATION ON PIG FATTENING STATION, GERMANYSupplied by EJOT: EJOT® Solar Fastening System
109
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
D i r e c t F a s t e n i n g
Dir
ect
Fast
enin
g
Shot � ring tool P 525 L
APPLICATION RANGE• Fastening of pro� led steel sheets
onto steel substrate � 6 mm
ADVANTAGES:• Ensures ergonomic working to reduce down-time
caused by health problems• Fatigue-free installation in upright position• Quick installation sequence
APPROVALZ-14.1-4ETA-08/0040
FEATURES• Automatic bolt, cartridge and piston feed• Bolt collator on the tool
TECHNICAL DATAMachine length .................................................. 1000 mmContact pressure ...................................................... 20 kgSetting energy .......................................................... 520 JCalibre .................................................................. 14 mmCartridge ..............................................................10 shots
INCLUDED IN DELIVERY1 shot � ring tool1 oil spray 35 ml1 protective goggles1 cleaning set1 operating manual1 transport box
Order descriptionWeight
kgPrice €/
pcs.Part number
Shot � ring tool P 525 L 9 9600110301
Accessories
Order descriptionPrice €/
pcs.Part number
Power damping element 9600132802Barrel 9600110954Cleaning set 9600074000Thrust piston 9600110957Protective goggles 9600074020Spray oil can 35 ml 9600310080Compressed ring 9600132801Telescopic ring 9600110948
Intermediate ring 9600132805
110
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
D i r e c t F a s t e n i n g
Dir
ect
Fast
enin
g
Shot � ring tool P 560
APPLICATION RANGE• Fastening of pro� led steel sheets onto
steel substrate � 6 mm• For fastening cassettes onto steel columns � 60 mm
ADVANTAGES:• Fast installation sequence through automated repetition• Compact and lightweight design• Quick release fastening system• Easy cleaning• Stability system for secure storage
APPROVALZ-14.1-4ETA-08/0040
FEATURES• Automatic bolt, cartridge and piston feed• Bolt collator on the tool
TECHNICAL DATAWeight incl. collator ................................................ 4,23 kgSetting energy .......................................................... 520 JCollator ............................................ 10 bolts/10 cartridgesCartridges ...................................... 6,3/16 (black, red, blue)Dimensions ......................H 277 mm / L 363 mm / W 77 mm
INCLUDED IN DELIVERY1 shot � ring tool1 oil spray 35 ml1 protective goggles1 cleaning set1 operating manual1 transport box
Accessories
Order descriptionPrice €/
pcs.Part number
Barrel 9600014139Cleaning set 74000Thrust piston 9600014137Protective goggles 9600011117Spray oil can 35 ml 9600310080Compressed ring 9600014136
Order descriptionWeight
kgPrice €/
pcs.Part number
P 560 shot � ring tool 4.23 9600013891
111
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
D i r e c t F a s t e n i n g
Dir
ect
Fast
enin
g
Cartridges 6,3/16blue, red, black
APPLICATION RANGE• For shot firing tool P 525 L• For shot firing tool P 560
APPROVALETA-08/0040
Tie pin HSBR 14collated for P 525 L
APPLICATION RANGE• For high strength substructures (e.g. S355 or higher)
APPROVALETA-08/0040
Tie pin HSBR 14collated for P 560
APPLICATION RANGE• For high strength substructures (e.g. S355 or higher)
APPROVALETA-08/0040
Order descriptionPrice €/100 pcs.
Part number
Blue cartridge: strong 9600003123Red cartridge: very strong 9600003122
Black cartridge: strongest 9600003121
Order descriptionCollator
capacitiy; pcs.Price €/100 pcs.
Part number
HSBR 14 tie pin, collated for P 525 L 9600003176
Order descriptionCollator
capacitiy; pcs.Price €/100 pcs.
Part number
Tie pin HSBR 14, collated for P 560 9600053953
112
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S c a f f o l d i n g f a s t e n e r s
Sca
ffol
ding
fa
sten
ers
EJOT® Scaffolding anchorsto anchor scaffolding in the industrial lightweight construction
FEATURES• GT scaffolding anchor and GU threaded sleeve
made of stainless steel• Ring bolt forged steel, zinc-plated and stainless steel
�(similar to DIN 582)
ADVANTAGES• For use in steel substrate
(Typ JZ 3 ... Ø 6,3 mm) • For use in timber substructure
(Typ JA 3 ... Ø 6,5 mm)• Length range GT 25 mm - 64 mm • Length range GT 15 mm - 210 mm • Repeat use of GU-threaded sleeve possible
NOTEEJOT® scaffolding anchor facilitate traction- and pressure-proof joints. They may only be loaded in axial direction of the screw. The relevant regulations and standards have to be observed.Scaffolding anchors may not be fastened to facade cladding elements, only directly to the building or to the substructure if it is suf� ciently dimensioned.
Characteristic tensile force NR.k [kN](at right angles with assembly level)
* Based on the approval of the screws ETA-10/0200 addendum 44 and 45** Based on the approval of the screws ETA-10/0200
Scaffolding anchor Thickness of the steel substrate tII in mm from S 235 Jxx (St 37)
JZ 3 - GU - 6,3 x L 2.0 3.0 4.0 5.0 6.0 � 7.0
Ø drill hole (mm) 5.3 5.3 5.3 5.5 5.5 5.7
Characteristic pull-out load ** (kN)
3.6 6.0 8.8 11.6 13.4 13.4
Scaffolding anchor Installation depth into the timber substructure in mmJA 3 - GU - 6,5 x L 30 50 60 75
Ø drill hole (mm) 4.5 4.5 4.5 4.5
Characteristic pull-out load ** (kN)
1.5 2.5 3.0 3.7
113
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S c a f f o l d i n g f a s t e n e r s
Sca
ffol
ding
fa
sten
ers
EJOT®
Scaffolding anchorJZ3-GT-6,3
APPLICATION RANGE• For installation into steel � 2 mm• For aluminium substructures � 3 mm
FEATURES• A2 stainless steel
TECHNICAL DATADrive .............................................hexalobular / TORX® T30 Sealing washer ......................................................... E16/2 High thread ................................................................ M10
CROSS REFERENCEAccessories ............................................ page 191
EJOT®
Scaffolding anchor JA3-GT-6,5
APPLICATION RANGE• For installation into wood
FEATURES• A2 stainless steel
TECHNICAL DATADrive .............................................hexalobular / TORX® T30 Sealing washer ......................................................... E16/2 High thread ................................................................ M10
CROSS REFERENCEAccessories ............................................ page 191
Ømm
Length of self-tapping screw [mm]
PUPrice €/100 pcs.
Order description Part number
6.3 25 50 JZ3-GT-6,3x25-E16/2 9411211311
6.3 64 50 JZ3-GT-6,3x64-E16/2 9411811311
Ømm
Length of self-tapping screw [mm]
PUPrice €/100 pcs.
Order description Part number
6.5 32 50 JA3-GT-6,5x32-E16/2 9413311311
6.5 64 50 JA3-GT-6,5x64-E16/2 9413811311
EJOT®
Ring bolt M10
APPLICATION RANGE• For JZ3-GT and JA3-GT scaffolding anchors
FEATURES• Zinc-plated forged steel (as per DIN 582)• A2 stainless steel
Ring diametermm
Female thread
PUPrice €/100 pcs.
Order description Part number
25.0 M10 50 Eyebolt M10-25 stainless steel 9430300300
25.0 M10 50 Eyebolt M10-25 steel 9430300501
114
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S c a f f o l d i n g f a s t e n e r s
Sca
ffol
ding
fa
sten
ers
EJOT®
Scaffolding anchor JA3-GU-6,5
J3
APPLICATION RANGE• For installation into wood
FEATURES• A2 stainless steel
TECHNICAL DATADrive ........................................................ hexagon A/F 3/8 Sealing washer ......................................................... E16/2 Threaded sleeve ................................................... M14x1,5
NOTEconsisting of EJOT® GU threaded sleeve and EJOT® JA3 self-tapping screw
CROSS REFERENCEAccessories ............................................ page 191
Self-tapping screw JA3-6,5 ...................... page 78
EJOT®
Scaffolding anchor JZ3-GU-6,3
J3
APPLICATION RANGE• For installation into steel � 2 mm• For installation into aluminium � 3 mm
FEATURES• Threaded sleeve and self-tapping screw made of A2
stainless steel
TECHNICAL DATADrive ........................................................ hexagon A/F 3/8 Sealing washer ......................................................... E16/2 Threaded sleeve ................................................... M14x1,5
NOTEConsisting of EJOT® GU threaded sleeve and EJOT® JZ3 self-tapping screw
Accessories ............................................ page 191
Self-tapping screw JZ3-6,3 ...................... page 80
Ømm
Effective length scaffolding
anchor [mm]
Length of self-tapping screw [mm]
PUPrice €/100 pcs.
Order description Part number
6.3 15 38 50 JZ3-GU-6,3x15-E16/2 94011113116.3 30 50 50 JZ3-GU-6,3x30-E16/2 94012113116.3 45 64 50 JZ3-GU-6,3x45-E16/2 94015113116.3 70 90 50 JZ3-GU-6,3x70-E16/2 94019113116.3 80 100 50 JZ3-GU-6,3x80-E16/2 94020113116.3 95 115 50 JZ3-GU-6,3x95-E16/2 94021113116.3 105 125 50 JZ3-GU-6,3x105-E16/2 94022113116.3 130 150 50 JZ3-GU-6,3x130-E16/2 94024113116.3 155 175 50 JZ3-GU-6,3x155-E16/2 94026113116.3 180 200 50 JZ3-GU-6,3x180-E16/2 9402811314
6.3 210 230 50 JZ3-GU-6,3x210-E16/2 9402911314
Ømm
Effective length scaffolding
anchor [mm]
Length of self-tapping screw [mm]
PUPrice €/100 pcs.
Order description Part number
6.5 55 75 50 JA3-GU-6,5x55-E16/2 94036113116.5 70 90 50 JA3-GU-6,5x70-E16/2 94039113116.5 80 100 50 JA3-GU-6,5x80-E16/2 94040113116.5 95 115 50 JA3-GU-6,5x95-E16/2 94041113116.5 105 125 50 JA3-GU-6,5x105-E16/2 94042113116.5 130 150 50 JA3-GU-6,5x130-E16/2 94044113116.5 155 175 50 JA3-GU-6,5x155-E16/2 9404611311
6.5 180 200 50 JA3-GU-6,5x180-E16/2 9404711311
115
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S c a f f o l d i n g f a s t e n e r s
Sca
ffol
ding
fa
sten
ers
EJOT®
GU ring bolt M14
APPLICATION RANGE• For universal scaffolding anchor GU
FEATURES• Zinc-plated forged steel (as per DIN 582)
EJOT®
GU threaded sleeve
FEATURES• A2 stainless steel
TECHNICAL DATA...................................................................... Wrench Size A/F 13Threaded sleeve ................................................... M14x1,5
NOTEAll EJOT® self-tapping screws of the types JZ3 Ø 6,3 and JA3 Ø 6,5 can be combined to a GU universal scaffolding anchor.Effective length of universal scaffolding anchor GU + 20 mm = length of screw required.
Ring diametermm
Female thread
PUPrice €/100 pcs.
Order description Part number
25.0 M14x1,5 50 GU M14 eyebolt 9409400501
Sleeve length mm
PUPrice €/100 pcs.
Order description Part number
18 50 GU threaded sleeve 9400100300
116
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
DEKTITE®
Pipe � ashings
APPLICATION RANGEDEKTITE® pipe � ashings provide a perfect seal for pipes on roofs and facades. Due to the � exible rubber pleats thermal changes in length of the pipes or sheathing elements are not obstructed. Fatigue fractures, which might occur with rigid pipe feed throughs, are impossible with DEKTITE � ashings.
FEATURES• Standard dimension for pipe diameters of up to 610 mm• Weather resistant due to building industry approved
EPDM• Unsusceptible to UV-radiation• Adaptable to all roof profiles
ADVANTAGES• Long service life• Thermal stability: for a short time: up to +150 °C
constant: up to +115 °C• Made of silicone for higher temperatures
up to +250 °C upon request• Low-temperature resistance: up to -50 °C• Flexible adjustment
- to various profiles- to all pipe materials- to pipe diameters up to 610 mm
• 20 year warranty on material
NOTEWhen using the DEKTITE® pipe � ashing please note the speci� cations stated in DIN 18807 "Öffnungen in Dächern" have to be considered.Pipe � ashings may not be installed in straight and transversal joints.
absorbing of the load through two � exible pleats
� exible, conical sleeve
easily identi� able pipe/cable bundle size
low pro� le
improved watertightnesslarge base
no twisting of the coneembedded aluminium frame
117
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
Dektite® ComboPipe Flashing Installation Kit
APPLICATION RANGE• For waterproo� ng pipes on corrugated metal roofs• For waterproo� ng pipes on corrugated � bre cement roofs• For subsequent waterproo� ng of pipes
ADVANTAGES• Perfect seal on roof and facade• No interference of thermal elongation of pipes• No fatigue fracture• Ideal for repairs of existing pipe systems
NOTEUse Bulbtite rivets for corrugated � bre-cement sheets
KIT INCLUDES1 pipe � ashing1 cartridge of EJOPLAST joint sealant1 EJOT® self-drilling screw set / optional EJOT® Bulbtite set1 clips set
NOTE FOR SUBSEQUENT WATERPROOFINGSee processing guidelines for Dektite® Retro� t
For pipe Ø mm
Basemm
Roof pitch
°
Cartridge capacity
ml
Screws/ clipspcs.
PUPrice
€/pcs.
Order description
Part number
400 - 750 935 x 970 - 310 70/10 1 DC110 8270004704400 - 450 - up to 45 - - - - - -500 - 550 - up to 30 - - - - - -600 - 660 - up to 15 - - - - - -730 - 750 - up to 6 - - - - - -
1. Adjust Dektite® to the pipe 2. Adjust Dektite® to the pro� led sheet and mark
3. Apply sealant
4. Adjust Dektite® to the shape of the pro� led sheet
5. Fasten Dektite® with EJOT® self-drilling screws or Bulbtite rivets
118
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
Dektite® SquarePipe Flashing
Installation Kit
APPLICATION RANGE• For waterproo� ng pipes on corrugated metal roofs• For waterproo� ng pipes on corrugated � bre cement roofs
ADVANTAGES• Perfect seal on roof and facade• No interference of thermal elongation of pipes• No fatigue fracture
NOTEUse Bulbtite rivets for corrugated � bre-cement sheets
KIT INCLUDES1 pipe � ashing1 cartridge of EJOPLAST joint sealant1 EJOT® self-drilling screw set / optional EJOT® Bulbtite set
1. Adjust Dektite® to the pipe 2. Adjust Dektite® to the pro� led sheet and mark
3. Apply sealant
4. Adjust Dektite® to the shape of the pro� led sheet
5. Fasten Dektite® with EJOT® self-drilling screws or Bulbtite rivets
For pipe Ø mm
Basemm
Roof pitch
°
Cartridge capacity
ml
Screwspcs.
PUPrice
€/pcs.
Order description
Part number
0 - 35 99 x 99 0 - 60 80 8 1 DFE 0-35 82000047045 - 55 137 x 137 0 - 35 80 8 1 DFE 5-55 82001047045 - 120 218 x 218 0 - 35 80 16 1 DFE 5-120 8200304704110 - 170 284 x 284 0 - 35 80 20 1 DFE 110-170 8200404704160 - 220 365 x 365 0 - 35 80 28 1 DFE 160-220 8200604704160 - 300 453 x 453 0 - 35 310 32 1 DFE 160-300 8200704704
290 - 440 581 x 581 0 - 35 310 40 1 DFE 290-440 8200904704
119
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
Dektite® EZi-SealPipe Flashing Installation Kit
APPLICATION RANGE• For waterproo� ng pipes on corrugated metal roofs • For waterproo� ng pipes on corrugated � bre cement roofs• no bonding!
ADVANTAGES• Non-absorbent, closed cell sealing surface• Seals under compression even on wet surfaces• Seals without use of a joint sealant• No interference of thermal elongation of pipes• No fatigue fracture
NOTEUse Bulbtite rivets for corrugated � bre-cement sheets
KIT INCLUDES1 pipe � ashing1 EJOT® self-drilling screw set / optional EJOT® Bulbtite set
1. Adjust Dektite® EZi-Seal to pipe 2. Adjust Dektite® EZi-Seal to the pro� led sheet and mark
3. Adjust Dektite® EZi-Seal accurately to the pro� led sheet
4. Fasten Dektite® EZi-Seal with EJOT® self-drilling screws or Bulbtite rivets
For pipe Ø mm
Basemm
Roof pitch°
Screwspcs.
PUPrice €/
pcs.Order description Part number
0 - 35 99 x 99 0 - 60 8 1 DFE 0-35 EZ 82000047065 - 55 137 x 137 0 - 35 8 1 DFE 5-55 EZ 82001047065 - 120 218 x 218 0 - 35 16 1 DFE 5-120 EZ 8200304706110 - 170 284 x 284 0 - 35 20 1 DFE 110-170 EZ 8200404706160 - 220 365 x 365 0 - 35 28 1 DFE 160-220 EZ 8200604706160 - 300 453 x 453 0 - 35 32 1 DFE 160-300 EZ 8200704706
290 - 440 581 x 581 0 - 35 40 1 DFE 290-440 EZ 8200904706
120
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
Dektite® SoakerPipe Flashing
Installation Kit
APPLICATION RANGE• For waterproo� ng pipes with large opening areas
ADVANTAGES• Large base ensures optimum positioning• Reliable and easy installation• Seals pipe and roof in a single work step• Prevents rainwater back-up
KIT INCLUDES1 pipe � ashing1 cartridge of EJOPLAST joint sealant1 EJOT® self-drilling screw set
1. Adjust Dektite® Soaker to the pipe
2. Adjust Dektite® Soaker to pro� led sheet and mark
3. Mark the outline of the soaker on the roof then remove it. Mark a lap allowance of 30mm (inside the original mark)
4. Cut out the roof inside of the marked 30mm area. Trim sharp edges. Timber supports must be installed to support the roof where ribs have been removed.
5. Apply sealant and � t Dektite® Soaker accurately to the pro� led sheet
6. Fix to the middle front and middle back of the Dektite® soaker and � x progressively towards the edge
7. Use provided metal strips to seal overlapping ends. Trim excess sides
For pipe Ø mm
Basemm
Roof pitch
°
Cartridge capacity
ml
Screwspcs.
PUPrice
€/pcs.
Order description
Part number
75 - 155 410 x 360 0 - 60 80 30 1 DF 602 8206024704114 - 254 485 x 460 0 - 60 80 36 1 DF 603 8206034704254 - 406 708 x 635 0 - 60 310 52 1 DF 605 8206054704
380 - 610 1006 x 905 0 - 60 310 96 1 DF 606 8206064704
121
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
Dektite® Retro� tPipe Flashing Installation Kit
APPLICATION RANGE• For subsequent waterproo� ng of pipes
in places dif� cult to access
ADVANTAGES• Ideal for repairs of existing pipe systems
FEATURES• Eeasy to lock
NOTEUse Bulbtite rivets for corrugated � bre-cement sheets
KIT INCLUDES1 pipe � ashing1 cartridge of EJOPLAST joint sealant1 EJOT® self-drilling screw set / optional EJOT® Bulbtite set
1. Adjust Dektite® Retro� t to the pipe
2. Place the Dektite® Retro� t raound the pipe and engage metal teeth in opposing pockets starting at the top
3. Fasten clips with pliers
4. Apply sealant and � t Dektite® Retro� t to pro� led sheet
5. Fasten Dektite® Retro� t with EJOT® self-drilling screws or Bulbtite rivets
For pipe Ø mm
Basemm
Roof pitch
°
Cartridge capacity
ml
Screwspcs.
PUPrice
€/pcs.
Order description
Part number
20 - 70 Ø 160 0 - 40 80 12 1 RF 801 826010470450 - 185 Ø 273 0 - 40 80 19 1 RF 802 826020470485 - 255 Ø 369 0 - 40 80 25 1 RF 803 8260304704
235 - 425 780 x 680 0 - 40 310 57 1 RFS 4 8260404704
122
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
Dektite® Strip FlashPipe Flashing
Installation Kit
APPLICATION RANGE• Sealing square pipe cross-sections
of more than 1 m side length or diameter• Forming expansion joints
FEATURES• Edge of sealing strip � 25 %
(accordion principle)• Use up to pro� le height � 35 mm
KIT INCLUDESDSFBNG: 2 cartridge of joint sealant(neutral curing silicone)DSFEG: 5 cartridgesof joint sealant (neutral curing silicone)1 EJOT® self-drilling screw set
Length m
Widthmm
Cartridge capacity ml
Screwspcs.
PUPrice €/
pcs.Order description
Part number
3.1 235 310 134 1 DSFBNG 8200006704
10 235 310 410 1 DSFEG 8200005704Further lengths upon request.
1. Trim 150 mm of the crown to guarantee water � ow
2. Do not mark the sealing line more than 75 mm above the purlin
3. Apply sealant below the sealing line
4. Trim every side of the Dektite® Strip Flash. Allow 200 - 300 mm for overlap
7. Apply sealant
10. Remove excess Dektite® Strip Flash. Overlap needs to be done thoroughly. Also apply sealing compound under the overlap on the edges
5. Fixing along the upper edge without stretching of the Dektite® Strip Flash
8. Fix to valley and to pro� le edges as shown
11. Fix the corners with provided metal strip
6. Press Dektite® Strip Flash to thepro� led sheet by hand. Do not use tools!
9. Stretch the corners of the overlapping upper part of the Dektite® Strip Flash and push down. Attach the uper corner
12. Apply sealing compound acroos the edges and form a ridge in order to slow down the water � ow
Nothigher
than75 mm
123
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
A c c e s s o r i e s
EJOT®
Hose clamp
APPLICATION RANGE• A reliable seal between pipe and pipe � ashing
INSTALLATION NOTEPierce the marking for the clamp or cable tie at the joint, pull through, place around the Dektite® Retro� t and close.
EJOT®
Universal hose clamp
APPLICATION RANGE• A reliable seal between pipe and pipe � ashing
FEATURES• For diameters from 150 mm onwards
ORDER NOTEUniversal hose clamp consisting of tightener and universal cable tie. Length of universal cable tie � pipe circumference + 50 mm
INSTALLING THE CABLE TIETip back the hinged screw in the tightener, insert one end of the universal cable tie through the clamp lock and twist about 15 mm. Place universal fastener strap around Dektite®, insert through the tightener and tighten by hand. Hinge the screw inwards and tighten as far as possible with a screwdriver.
For pipe diametermm
PU Price €/ pcs. Order description Part number
40 - 60 1 Hose clamp 40-60 820000630060 - 80 1 Hose clamp 60-80 820000830070 - 90 1 Hose clamp 70-90 820000930090 - 110 1 Hose clamp 90-110 8200011300110 - 130 1 Hose clamp 110-130 8200013300
130 - 150 1 Hose clamp 130-150 8200015300
Widthmm
PUPrice
€Order description Part number
- 1 per piece Tightener 82000773007 1 per m Cable tie 8200076300
124
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
P i p e f l a s h i n g s
Pip
e fl
ashi
ngs
A c c e s s o r i e s
EJOPLASTJoint Sealant
APPLICATION RANGE• For sealing the pipe � ashing
FEATURESEJOPLAST is a single-component universal sealant based on polycarboxylic acid copolymeric base.
EJOPLAST adheres to all conventional materials such as steel, aluminium, copper, brass, glass, wood, ceramic, bitumen, concrete, masonry, plaster, plexiglas, tiles, roof tiles, polyester, roo� ng paper, etc. Smooth, non-porous substruc-tures can even be wet, while porous surfaces should be dry.
EJOPLAST can be cleaned with standard cleaning agents, but not with solvents.EJOPLAST hardens through the evaporation of solvents and is impervious to water from the beginning because it forms an immediate skin.The surface is adhesive-free after 20-30 minutes (depending on temperature), likewise immediately after contact with water (e.g. by planing).
EJOT®
Hand gun
Contentsmm
Colour PUPrice
€ / pcs.Order description Part number
80 clear 1 EJOPLAST 80 mm clear 8200003000310 clear 1 EJOPLAST 310 mm clear 8200001000
Order descriptionPrice €/
pcs.Part number
Hand Gun 9559942000
125
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
P i p e f l a s h i n g sN o t e s
Pip
e fl
ashi
ngs
SEDUS STOLL AG, DOGERN, DEUTSCHLAND © Sedus Stoll AGSupplied by EJOT: EJOT® SUPER-SAPHIR self-drilling screw JT3
126
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
DABO® SELF-DRILLING SCREWS BY EJOT®
• Very high corrosion protection due to high-quality Climadur* coating „R“
• Alternative corrosion resistance stainless steel "E"• Resistant to imposed loads• Screws and plates available collated or belt-fed• No loosening
EJOT® STRESS PLATES• Metal plates, made of alu-zinc coated steel• Plastic plates made of high-grade polyamide• Geometry optimised for roofing membranes• Screws and plates available collated or belt-fed
FEATURES• Variable length combinations up to 400 mm insulation
thickness• Minimal thermal bridging• Approved flat roofing fasteners acc. to ETAG 006• New EJOT® complete product range with solutions for
almost all applications• Approved corrosion protection acc. to strictest
regulations• Economical processing with EJOT® ECOset installation
tool
EJOT® AERATED CONCRETE SCREWS• Secure fastening of roofing membrane and thermal
insulation to aerated concrete• Flat roofing fastener approved in the ETA-07/0013• No pre-drilling necessary• Suitable for metal and plastic plates• Telescope effect in combination with
EJOT® EcoTek stress plate• Corrosion resistant (A4 stainless steel)
EJOT® CONCRETE SCREWS• Case-hardened steel• Very high corrosion protection due to high-quality
Climadur* coating „R“• Suitable for metal and plastic plates• Telescope effect in combination with
EJOT® EcoTek stress plate• Flat roofing fastener approved in the ETA-07/0013• Fastening without additional anchor
*CLIMADUR• High-grade coating to improve
the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
Recommended � at roo� ng system combinations
substructure
sheet steel woodaerated
concrete2)con-crete
pumice board 1),2)
hollow block ceiling 1), 2) Others
ther
mal
insu
latio
n
mineral � bre
TKR/TKE + HTKA/F 8 RT + HTV
FPS-E + EcoTek
FDD
FBS-R +
EcoTek
FDD
FDD FDD after consultation
with our service team
polystyrene
rigid foam
withoutInsulation
A/F 8-R + HTV F
FPS-E + HTV F
FBS-R + HTV F
Others after consultation with our service team1) Recommendation De� nition of the design load only after pull-out tests by our service team2) As a rule, pull-out tests have to be arranged with our service team for all renovation cases
SYSTEM OVERVIEW
EJOT® Fastening Systems substructure
screw stress platesheet steel0,75 mm S280GD1)
timberT&G boarding2)
plywood BFU 1003)
OSB4)
concreteC12/155)
aerated concrete
P3.3 / 0,506)
Dabo® TKR/E-4,8xL HTK X X
Dabo® TKR/E-4,8xL HTV 82/40 TK X X
Dabo® TKR/E-4,8xLHTV 82/40 F
X X
Dabo® A/F8R(T)-4,8xL X X
Dabo® A/F8R(T)-4,8xL HTV 82/40 X X
FBS-R-6,3xL HTV 82/40 F X7)
FBS-R-6,3xL EcoTek 50 X7)
FPS-E-8,0xL HTV 82/40 F X8)
FPS-E-8,0xL EcoTek 50 X8)
FDD-50xL X9) X10)
1) S280GD-EN 10326, thickness tmin = 0,75 mm;
2) T&G boarding: EN 338/C24, thickness � 25 mm;
3) plywood: EN 636: 2003-11; BFU 100: DIN 68705-3, thickness � 21
mm;
4) OSB EN 300, EN 13986:2002-09; thickness � 18 mm;
5) C 12/15 EN 206;
6) P 3.3 / 5,0 EN 12602;
7) embedment depth � 30 mm;
8) embedment depth � 60 mm;
9) drill-hole diameter 10 mm, embedment depth � 30 mm;
10) drill-hole diameter 8 mm, embedment depth � 50 mm
NOTEOther combinations of the � at roo� ng system componentes are also possible!Ask our service team!
127
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
EJOT® stress plateHTK 50
EJOT® stress plateHTV 82/40 TK
EJOT® stress plateHTV 82/40
EJOT® stress plateHTV 82/40 F
EJOT® stress plateHTV 40 RU
EJOT® stress plateEcoTek 50
Self-
drill
ing
scre
wEJ
OT D
abo®
A/F
8 R
-4,8
Self-
drill
ing
scre
wEJ
OT D
abo®
A/F
8 RT
-4,8
Self-
drill
ing
scre
wEJ
OT D
abo®
TKR
-4,8
Self-
drill
ing
scre
wEJ
OT D
abo®
TKE
-4,8
EJOT
® c
oncr
ete
scre
wFB
S-R-
6,3
EJOT
® a
erat
ed c
oncr
ete
scre
w F
PS-E
-8,0
COMBINATION MATRIX ACC. TO ETA-07/0013
128
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
C l i m a d u r c o a t e d
EJOT Dabo® Screw A/F 8 R-4,8
with A/F8 hexagonal head
J2
APPLICATION RANGE• For fixing roofing membrane to sheet steel
substructures � 0,75 mm � 1 mm• In combination with EJOT® stress plate HTV 82/40• For timber substructure
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
APPROVALETA-07/0013
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Drive ............................................................ hexagon A/F8
Length determination for:sheet steel: ............................ insulation thickness +20 mmtimber: ................................... insulation thickness +30 mm* Min. lengths
CROSS REFERENCEHTV stress plate 82/40............................. page 134
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
bulk packed4.8 80 250 A/F8R-4,8x80 34871006294.8 100 250 A/F8R-4,8x100 34873006294.8 120 250 A/F8R-4,8x120 34875006294.8 140 200 A/F8R-4,8x140 34877006294.8 160 200 A/F8R-4,8x160 34879006294.8 180 200 A/F8R-4,8x180 34881006294.8 200 200 A/F8R-4,8x200 34883006294.8 220 200 A/F8R-4,8x220 34884006294.8 240 150 A/F8R-4,8x240 3488600629
4.8 260 250 A/F8R-4,8x260 3488800629
129
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
C l i m a d u r c o a t e d
EJOT Dabo® Screw A/F 8 RT-4,8with A/F8 hexagonal head and supporting thread
J2
APPLICATION RANGE• For fixing roofing membrane to sheet steel
substructures � 0,75 mm � 1 mm • Support thread designed to engage in the stress plate for
resistance to imposed loads• In combination with EJOT® stress plate HTV 82/40• For timber substructure
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
APPROVALETA-07/0013
TECHNICAL DATADrilling capacity t
I + t
II ............................................ 2,0 mm
Drive ............................................................ hexagon A/F8
Length determination for:sheet steel: ............................ insulation thickness +20 mmtimber: ................................... insulation thickness +30 mm* Min. lengths
CROSS REFERENCEHTV stress plate 82/40............................. page 134
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
bulk packed4.8 80 250 A/F8RT-4,8x80 34771006294.8 100 250 A/F8RT-4,8x100 34773006294.8 120 250 A/F8RT-4,8x120 34775006294.8 140 200 A/F8RT-4,8x140 34777006294.8 160 200 A/F8RT-4,8x160 34779006294.8 180 200 A/F8RT-4,8x180 34781006294.8 200 200 A/F8RT-4,8x200 34783006294.8 220 200 A/F8RT-4,8x220 34784006294.8 240 150 A/F8RT-4,8x240 34786006294.8 260 250 A/F8RT-4,8x260 3478800629belted4.8 80 750 A/F8RT-4,8x80-belted 34771016294.8 100 750 A/F8RT-4,8x100-belted 34773016294.8 120 750 SW8RT-4,8x120-belted 34775016294.8 140 750 A/F8RT-4,8x140-belted 34777016294.8 160 750 A/F8RT-4,8x160-belted 34779016294.8 180 750 A/F8RT-4,8x180-belted 34781016294.8 200 750 A/F8RT-4,8x200-belted 34783016294.8 220 750 A/F8RT-4,8x220-belted 34784016294.8 240 750 A/F8RT-4,8x240-belted 3478601629
4.8 260 750 A/F8RT-4,8x260-belted 3478801629
130
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
C l i m a d u r c o a t e d
EJOT Dabo®
Screw TKR-4,8with bugle head
APPLICATION RANGE• For fixing roofing membrane to sheet steel
substructures � 0,75 mm � 1 mm• For timber substructure• In combination with EJOT® HTK 50 stress plate• In combination with EJOT® stress plate HTV 82/40 F• In combination with EJOT® stress plate HTV 82/40 F
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Can be delivered belted for EJOT® ECOset installation tool or pre-assembled with EJOT® stress plates HTK for EJOT® ECOset HTK installation tool
APPROVALETA-07/0013
TECHNICAL DATADrilling capacity t
I + t
II ............................................ 2,0 mm
Drive ......................................................... H2 cross recess
Length determination for:sheet steel: ............................ insulation thickness +20 mmtimber: ................................... insulation thickness +30 mm* Min. lengths
CROSS REFERENCEStress plate HTK 50 ................................. page 136
Stress plate HTV 82/40 TK ........................ page 134
Stress plate HTV 82/40 F .......................... page 135
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174 ECOset HTK installation tool ..................... page 175
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
bulk packed4.8 35 500 TKR-4,8x35 34967006294.8 50 500 TKR-4,8x50 34968006294.8 60 500 TKR-4,8x60 34969006294.8 70 500 TKR-4,8x70 34970006294.8 80 500 TKR-4,8x80 34971006294.8 90 250 TKR-4,8x90 34972006294.8 100 250 TKR-4,8x100 34973006294.8 110 250 TKR-4,8x110 34974006294.8 120 250 TKR-4,8x120 34975006294.8 130 250 TKR-4,8x130 34976006294.8 140 200 TKR-4,8x140 34977006294.8 150 200 TKR-4,8x150 34978006294.8 160 200 TKR-4,8x160 34979006294.8 170 200 TKR-4,8x170 34980006294.8 180 200 TKR-4,8x180 34981006294.8 200 200 TKR-4,8x200 34983006294.8 220 200 TKR-4,8x220 34984006294.8 240 200 TKR-4,8x240 34986006294.8 260 250 TKR-4,8x260 34988006294.8 280 250 TKR-4,8x280 34989006294.8 300 250 TKR-4,8x300 3499000629
Order information: Further lengths upon request. Also available belted for ECOset or pre-assembled with HTK for ECOset HTK.
131
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
C l i m a d u r c o a t e d
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
4.8 70 500 TKR-3-4,8x70 34370006394.8 90 500 TKR-3-4,8x90 3437200639
4.8 110 250 TKR-3-4,8x110 3437400639
EJOT Dabo®
Screw TKR-3-4,8with bugle head
APPLICATION RANGE• For fixing roofing membrane to sheet steel substructure
� 1 mm � 3 mm • In combination with EJOT® HTK 50 stress plate• In combination with EJOT® stress plate HTV 82/40 F• In combination with EJOT® stress plate HTV 82/40 F
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
• Can be delivered belted for EJOT® ECOset installation tool or pre-assembled with EJOT® stress plates HTK for EJOT® ECOset HTK installation tool
TECHNICAL DATADrilling capacity t
I + t
II .............................................3,0 mm
Drive ......................................................... H2 cross recess
CROSS REFERENCEStress plate HTK 50 ................................. page 136
Stress plate HTV 82/40 TK ........................ page 134
Stress plate HTV 82/40 F .......................... page 135
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174 ECOset HTK installation tool ...................... page 175
132
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
C l i m a d u r c o a t e d
EJOT Dabo®
Screw VHT-R-4,8
APPLICATION RANGE• For � xing roo� ng membrane to single-ply sheet steel
substructure � 0,60 � 0,75 mm • In combination with EJOT® HTK 50 stress plate• In combination with EJOT® HTV 82/40 TK stress plate• For timber substructure• In combination with EJOT® HTV 82/40 F stress plate• In combination with EJOT® stress plate HTV 40 RU
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
TECHNICAL DATADrive ......................................................... H2 cross recess
NOTEFor thicker and/or two-ply sheet steel we recommend the use of the EJOT Dabo® screw TKR-4,8.
CROSS REFERENCEStress plate HTK 50 ................................. page 136
Stress plate HTV 82/40 TK ........................ page 134
Stress plate HTV 82/40 F .......................... page 135
Stress plate HTV 40 RU ............................ page 135
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174 ECOset HTK installation tool ...................... page 175
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
4.8 35 500 VHT-R-4,8x35 34967006094.8 50 500 VHT-R-4,8x50 34968006094.8 60 500 VHT-R-4,8x60 34969006094.8 70 500 VHT-R-4,8x70 34970006094.8 80 500 VHT-R-4,8x80 34971006094.8 90 250 VHT-R-4,8x90 34972006094.8 100 250 VHT-R-4,8x100 34973006094.8 120 250 VHT-R-4,8x120 34975006094.8 140 200 VHT-R-4,8x140 34977006094.8 160 200 VHT-R-4,8x160 34979006094.8 180 200 VHT-R-4,8x180 3498100609
4.8 200 200 VHT-R-4,8x200 3498300609
133
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
F l a t r o o f i n g S e l f - d r i l l i n g s c r e w s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
A 4 s t a i n l e s s s t e e l
EJOT Dabo® Screw TKE-4,8with bugle head
APPLICATION RANGE• To fix roofing membrane onto sheet steel substructures
� 0,75 mm � 1 mm in combination with HTK 50
• For timber substructures in combination with HTV 82/40 TK and HTV 82/40 F
FEATURES• A4 stainless steel with case-hardened drill point• Can be delivered collated for EJOT® ECOset installation
tool or pre-assembled with HTK for EJOT® ECOset HTK.
APPROVALETA-07/0013
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Drive ......................................................... H2 cross recess
CROSS REFERENCEStress plate HTK 50 ................................. page 136
Stress plate HTV 82/40 TK ........................ page 134
Stress plate HTV 82/40 F .......................... page 135
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174 ECOset HTK installation tool ...................... page 175
Ømm
Length mm
PUPrice €/100 pcs.
Order description Part number
bulked4.8 50 500 TKE-4,8x50 73841083014.8 60 500 TKE-4,8x60 73841093014.8 70 500 TKE-4,8x70 73841103014.8 80 250 TKE-4,8x80 73841113014.8 90 250 TKE-4,8x90 73841123014.8 100 250 TKE-4,8x100 73841133014.8 120 250 TKE-4,8x120 7384132301
4.8 140 200 TKE-4,8x140 7384125301
134
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S t r e s s p l a t e s / f l a t r o o f i n g a n c h o r s
Str
ess
plat
es/
flat
roo
fing
an
chor
s
M e t a l s t r e s s p l a t e s
EJOT®
Stress plate HTV 82/40for hexagon head screws
APPLICATION RANGE• For securing roofing membrane onto substructure• For renovations• For installation with the EJOT® ECOset L tool• For combination with EJOT Dabo® Schrauben
SW 8 R, SW 8 RT• For new buildings• For manual installation
FEATURES• Alu-zinc coated steel
APPROVALETA-07/0013
CROSS REFERENCEDabo® screws A/F 8 RT-4,8 ...................... page 129
Dabo® screws A/F 8 R-4,8 ........................ page 128
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174
EJOT®
Stress plate HTV 82/40 TKfor bugle head screws
APPLICATION RANGE• For securing roofing membrane onto substructure• For renovations• For installation with the EJOT® ECOset L tool• For combination with EJOT Dabo® screws TKR and TKE• For new buildings• For manual installation
FEATURES• Alu-zinc coated steel
APPROVALETA-07/0013
CROSS REFERENCEDabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 .............................. page 133
ECOset installation tool............................. page 173 ECOset L installation tool .......................... page 174
Widthmm
Length mm
PUPrice €/100 pcs.
Order description Part number
40 82 1,000 HTV-82/40 3020095401
Widthmm
Length mm
PUPrice €/100 pcs.
Order description Part number
40 82 1,000 HTV-82/40 TK 3020098401
135
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S t r e s s p l a t e s / f l a t r o o f i n g a n c h o r s
Str
ess
plat
es/
flat
roo
fing
an
chor
s
M e t a l s t r e s s p l a t e s
EJOT®
Stress plate HTV 82/40 Ffor solid substructure
APPLICATION RANGE• For securing roofing membrane onto substructure• For fastening onto solid substructure
in combination with all EJOT Dabo® screws• In combination with EJOT® concrete screw FBS-R
and gas concrete screw FPS-E
FEATURES• Alu-zinc coated steel
APPROVALETA-07/0013
NOTEFor combination with all EJOT Dabo® screws
CROSS REFERENCEDabo® screw SW 8 RT-4,8 ........................ page 129
Dabo® screw SW 8 R-4,8 ......................... page 128
Dabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 .............................. page 133
Concrete screw FBS-R ............................. page 139
Gas concrete screw FPS-E ........................ page 140
EJOT®
Stress plate HTV RU
APPLICATION RANGE• For securing roofing membrane in combination with
EJOT Dabo® screws TKR and TKE• For fastening pressure-proof insulation in combination
with EJOT® concrete screw FBS-R and gas concrete screw FPS-E
FEATURES• Alu-zinc coated steel
APPROVALETA-07/0013
CROSS REFERENCEDabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 .............................. page 133
Concrete screw FBS-R ............................. page 139
Gas concrete screw FPS-E-8,0 .................. page 140
Widthmm
Length mm
PUPrice €/100 pcs.
Order description Part number
40 82 500 HTV-82/40 F 3020093401
diameter:mm
PUPrice €/100 pcs.
Order description Part number
40 1,000 HTV-40 RU 3020041401
70 500 HTV-70 RU* 3020096401*no approval
136
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S t r e s s p l a t e s / f l a t r o o f i n g a n c h o r s
Str
ess
plat
es/
flat
roo
fing
an
chor
s
P l a s t i c s t r e s s p l a t e s
EJOT®
Stress plate HTK 50for bugle head screws
APPLICATION RANGE• To secure roofing membrane• For new buildings• For special requirements of resistance to imposed loads• For reduction of thermal bridges
FEATURES• Polyamide• Telescope design, prevents screw head protrusion due
to foot traffic even with soft insulating material
APPROVALETA-07/0013
NOTEFor combination with EJOT Dabo® screws TKR and TKE
CROSS REFERENCEDabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 ............................. page 133
ECOset installation tool............................. page 173 HSK-HTK manual installation tool .............. page 176
EJOT®
Stress plate EcoTek 50
APPLICATION RANGE• To secure roofing membrane• For special requirements of resistance to imposed loads• For reduction of thermal bridges
FEATURES• High-grade plastic material• In combination for insulation material thicknesses up to
400 mm (FBS-R) and up to 490 mm (TKR)• Telescope design, prevents screw head protrusion due
to foot traffic even with soft insulating material
APPROVALETA-07/0013
NOTEFor combination with gas concrete screw FPS-E-8,0 and concrete screw FBS-R-6,3
CROSS REFERENCEConcrete screw FBS-R ............................. page 139
Gas concrete screw FPS-E ........................ page 140
Ø platemm
Effective shaft length L mm
PUPrice €/
100 pcs.Order description Part number
50 35 1,800 HTK-50x35 859703501050 55 1,500 HTK-50x55 859705501050 95 850 HTK-50x95 859709501050 115 800 HTK-50x115 859711501050 145 600 HTK-50x145 8597145010
50 185 400 HTK-50x185 8597185010
Ø platemm
Effective shaft length L mm
PUPrice €/
100 pcs.Order description Part number
50 25 2,000 EcoTek-50x35 859503500750 55 1,300 EcoTek-50x65 859506500750 95 900 EcoTek-50x105 859510500750 155 450 EcoTek-50x165 8595165007
50 215 500 EcoTek-50x225 8595225007
137
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
S t r e s s p l a t e s / f l a t r o o f i n g a n c h o r s
Str
ess
plat
es/
flat
roo
fing
an
chor
s
P l a s t i c s t r e s s p l a t e s
Insulation thickness mm
Effective shaft length L
mm
Screw length
mmPU
Price €/100 pcs.
Order description Part number
with EJOT Dabo® screw TKR60 35 50 1,000 HTK-M/TKR-60-35/50 370359689170 35 60 1,000 HTK-M/TKR-70-35/60 370359699180 55 50 1,000 HTK-M/TKR-80-55/50 370559689190 55 60 1,000 HTK-M/TKR-90-55/60 3705596991100 55 70 1,000 HTK-M/TKR-100-55/70 3705597091110 55 80 1,000 HTK-M/TKR-110-55/80 3705597191120 95 50 1,000 HTK-M/TKR-120-95/50 3709596891130 95 60 1,000 HTK-M/TKR-130-95/60 3709596991140 95 70 1,000 HTK-M/TKR-140-95/70 3709597091150 95 80 1,000 HTK-M/TKR-150-95/80 3709597191160 95 90 1,000 HTK-M/TKR-160-95/90 3709597291170 145 50 700 HTK-M/TKR-170-145/50 3714596891180 145 60 700 HTK-M/TKR-180-145/60 3714596991190 145 70 700 HTK-M/TKR-190-145/70 3714597091200 145 80 700 HTK-M/TKR-200-145/80 3714597191210 145 90 700 HTK-M/TKR-210-145/90 3714597291220 145 100 700 HTK-M/TKR-220-145/100 3714597391230 145 110 700 HTK-M/TKR-230-145/110 3714597491240 145 120 700 HTK-M/TKR-240-145/120 3714597591250 145 130 700 HTK-M/TKR-250-145/130 3714597691260 145 140 700 HTK-M/TKR-260-145/140 3714597791with EJOT Dabo® screw TKE60 35 50 1,000 HTK-M/TKE-60-35/50 370350684170 35 60 1,000 HTK-M/TKE-70-35/60 370350694180 55 50 1,000 HTK-M/TKE-80-55/50 3705506841100 55 70 1,000 HTK-M/TKE-100-55/70 3705507041110 55 80 1,000 HTK-M/TKE-110-55/80 -120 95 50 1,000 HTK-M/TKE-120-95/50 3709506841130 95 60 1,000 HTK-M/TKE-130-95/60 3709506941140 95 70 1,000 HTK-M/TKE-140-95/70 3709507041150 95 80 1,000 HTK-M/TKE-150-95/80 -160 95 90 1,000 HTK-M/TKE-160-95/90 3709507241170 145 50 700 HTK-M/TKE-170-145/50 3714506841180 145 60 700 HTK-M/TKE-180-145/60 3714506941190 145 70 700 HTK-M/TKE-190-145/70 3714507041200 145 80 700 HTK-M/TKE-200-145/80 -210 145 90 700 HTK-M/TKE-210-145/90 3714507241220 145 100 700 HTK-M/TKE-220-145/100 -230 145 120 700 HTK-M/TKE-230-145/110 -240 145 120 700 HTK-M/TKE-240-145/120 -250 145 140 700 HTK-M/TKE-250-145/130 -260 145 140 700 HTK-M/TKE-260-145/140 -
Order information: For wooden substructures screws need to be chosen 10 mm longer
EJOT®
Stress plate HTK-Mcollated
APPLICATION RANGE• To secure roofing membrane• For new buildings• For installation with the EJOT® ECOset HTK tool• For special requirements of resistance to imposed loads• For reduction of thermal bridges• For renovations• For manual installation
FEATURES• TKR = Case-hardened steel, Climadur coated• TKE = A4 stainless steel• Polyamide• Collated• Telescope design, prevents screw head protrusion due
to foot traffic even with soft insulating material• Combinations for insulation thicknesses up to 400 mm
on request
*CLIMADUR• High-grade coating to improve
the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
APPROVALETA-07/0013
TECHNICAL DATADrilling capacity t
I + t
II .............................................2,0 mm
Collator capacity ............................................................ 25
NOTEFor combination with EJOT Dabo® screws TKR and TKE drilling capacityt = 3 mm upon request!
CROSS REFERENCEDabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 .............................. page 133
ECOset HTK installation tool ...................... page 175
138
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
S t r e s s p l a t e s / f l a t r o o f i n g a n c h o r s
Str
ess
plat
es/
flat
roo
fing
an
chor
s
F l a t r o o f i n g a n c h o r s
EJOT®
Flat roo� ng anchor FDD-50
APPLICATION RANGE• To secure roofing membrane • For concrete substructures and
aerated concrete (gas concrete)• For pumice boardsubstructures1), 2),
hollow block ceilings1), 2) and similar building material
FEATURES• Anchor sleeve: Polyamide• Expansion nail: zinc-plated• Nail head: insert moulded plastic
TECHNICAL DATAAerated concrete � P 3.3 hole diameter ...................... 8 mmAerated concrete � P 3.3 embedment depth ......... � 50 mmConcrete � B 15 hole diameter ............................ � 10 mmConcrete � B 15 embedment depth ...................... � 30 mm
NOTEAS spacer – to prevent premature expansion of the anchor sleeve1) Recommendation De� nition of the design load only after
pull-out tests by our service team2) As a rule, pull-out tests have to be arranged with our service
team for all renovation cases
CROSS REFERENCEAS spacer ............................................... page 194
Ø platemm
Anchor length
mm
Aerated concrete � P 3.3 total
height
Concrete � B 15 total
heightPU
Price €/100 pcs.
Order description
Part number
50 55 5 25 200 FDD-50x55 852005528050 75 25 45 200 FDD-50x75 852007525050 95 45 65 200 FDD-50x95 852009522050 115 65 85 200 FDD-50x115 852011526050 135 85 105 200 FDD-50x135 852013521050 155 105 125 200 FDD-50x155 852015528050 175 125 145 200 FDD-50x175 852017523050 200 150 170 100 FDD-50x200 852020028050 220 170 190 100 FDD-50x220 852022025050 240 190 210 100 FDD-50x240 852024023050 260 210 230 100 FDD-50x260 852026026050 280 230 250 100 FDD-50x280 8520280240
50 300 250 270 100 FDD-50x300 8520300270
139
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
C o n c r e t e - / a e r a t e d c o n c r e t e s c r e w s
(Aer
ated
) co
ncre
te
scre
ws
C l i m a d u r c o a t e d
EJOT®
Concrete screws FBS-R-6,3
APPLICATION RANGE• To secure roo� ng membrane to concrete substructures • In combination with EJOT® stress plate EcoTek 50• In combination with EJOT® stress plate HTV 82/40 F• In combination with EJOT® stress plate HTV 40 RU
FEATURES• Case-hardened steel• Climadur coated – high-quality coating
to improve the corrosion protection (15 Kesternich cycles, DIN 50018, 1997)
APPROVALETA-07/0013
TECHNICAL DATADrive .............................................hexalobular / TORX® T30 Embedment depth � ............................................... 30 mmHole depth � .......................................................... 45 mm
NOTEDrill nominal diameter 5.0 mm
CROSS REFERENCEStress plate EcoTek 50 ............................. page 136
Stress plate HTV 82/40 F .......................... page 135
Stress plate HTV 40 RU ............................ page 135
Hammer drill bit SDS-plus ........................ page 184
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
6.3 35 500 FBS-R-6,3x35 57630355126.3 60 500 FBS-R-6,3x60 57630605126.3 80 250 FBS-R-6,3x80 57630805126.3 100 250 FBS-R-6,3x100 57631005126.3 120 250 FBS-R-6,3x120 57631205126.3 140 200 FBS-R-6,3x140 57631405126.3 180 200 FBS-R-6,3x180 5763180512
6.3 220 200 FBS-R-6,3x220 5763220512
DescriptionPrice €/
pcs.Order description
Drill bit extension 500mm SDS 9151950000Blade retainer for EcoTek (drill bit extension) 9151510071Hammer drill bit „A“ cone 5,0 x 35/102 9200050035Hammer drill bit „A“ cone 5,0 x 45/112 9200050045Hammer drill bit „A“ cone 5,0 x 52/119 9200005052Hammer drill bit „A“ cone 5,0 x 160 9200050160Hammer drill bit „A“ cone 5,5 x 160 9200055160Hammer drill bit SDS-plus 5,0 x 250/310 9200000028 Hammer drill bit SDS-plus 5,5 x 200/260 9200000021Hammer drill bit SDS-plus 5,5 x 250/310 9200000042Bit TORX® T30-M6x33 9250251430
Tools and accessories forFBS-R-6,3 and FPS-E-8,0
EJOT® stress plate EcoTek 50 x L
Insulation thickness
35 65 105 165 225
EJOT
® c
oncr
ete
scre
w
FBS-
R-6,
3 x
L
60 50 80 120 180 240
80 70 100 140 200 260
100 90 120 160 220 280
120 110 140 180 240 300
140 130 160 200 260 320
180 170 200 240 300 360
220 210 240 280 340 400
140
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
C o n c r e t e - / a e r a t e d c o n c r e t e s c r e w s
(Aer
ated
) co
ncre
te
scre
ws
A 4 s t a i n l e s s s t e e l
EJOT® Aerated concrete screw FPS-E-8,0
APPLICATION RANGE• To secure roo� ng membrane
to gas concrete substructures2)
• In combination with EJOT® stress plate EcoTek 50• In combination with EJOT® stress plate HTV 82/40 F• In combination with EJOT® stress plate HTV 40 RU
FEATURES• A4 stainless steel• Approved for gas concrete P3.3 onwards• No pre-drilling
APPROVALETA-07/0013
TECHNICAL DATADrive .............................................hexalobular / TORX® T30 Embedment depth � ................................................60 mm
NOTE2) As a rule, pull-out tests have to be arranged with our service
team for all renovation cases.
CROSS REFERENCEStress plate EcoTek 50 ............................. page 136
Stress plate HTV 82/40 F .......................... page 135
Stress plate HTV 40 RU ............................ page 135
Ømm
Length mm
PUPrice €/
100 pcs.Order description Part number
8.0 80 250 FPS-E-8,0x80 55800803008.0 100 250 FPS-E-8,0x100 55801003008.0 120 250 FPS-E-8,0x120 55801203008.0 160 200 FPS-E-8,0x160 55801603008.0 200 200 FPS-E-8,0x200 5580200300
8.0 240 150 FPS-E-8,0x240 5580240300
DescriptionPrice €/
pcs.Order description
Drill bit extension 500mm SDS 9151950000Blade retainer for EcoTek (drill bit extension) 9151510071Hammer drill bit „A“ cone 5,0 x 35/102 9200050035Hammer drill bit „A“ cone 5,0 x 45/112 9200050045Hammer drill bit „A“ cone 5,0 x 52/119 9200005052Hammer drill bit „A“ cone 5,0 x 160 9200050160Hammer drill bit „A“ cone 5,5 x 160 9200055160Hammer drill bit SDS-plus 5,0 x 250/310 9200000028 Hammer drill bit SDS-plus 5,5 x 200/260 9200000021Hammer drill bit SDS-plus 5,5 x 250/310 9200000042Bit TORX® T30-M6x33 9250251430
Tools and accessories forFBS-R-6,3 and FPS-E-8,0
EJOT® stress plate EcoTek 50 x L
Insulation thickness
35 65 105 165 225
EJOT
® a
erat
ed c
oncr
ete
scre
w F
PS-E
-8,0
x L
100 60 90 130 190 250
120 80 110 150 210 270
160 120 150 190 250 310
200 160 190 230 290 350
240 200 230 270 330 390
141
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
C o n c r e t e - / a e r a t e d c o n c r e t e s c r e w sN o t e s
(Aer
ated
) co
ncre
te
scre
ws
TURNING TORSO, MALMÖ, SWEDEN © iStockphotoSupplied by EJOT: EJOT® SUPER-SAPHIR self-drilling screw JT3
142
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
Length range of anchors with zinc-plated steel screws Cr(VI)-free coating
Length [mm] SDF-S-10V
SDF-KB-10V
SDF-S-10H
SDF-KB-10H
SDF-S-8
SDF-KB-8
SDF-S-10U
SDF-KB-10L
SDF-S-14U
SDF-KB-14U
SDP-S-10S
SDP-KB-10S
SDP-S-14
SDP-KB-14
50 • •
60 • • •
70 • •
80 • • • • • • • • • •
100 • • • • • • • • • •
120 • • • • • • • • • • •
140 • • • • • • • • • •
160 • • • • • • • •
180 • • • • • • • • • •
200 • • • • •1) •1) • •
220 • • • • •1) •1) • • • •
250 •
260 •
275 •
300 • •
360 •
1) Delivery time upon request
Length range of anchors with A4 stainless steel screws
Length [mm] SDF-S-10V
SDF-KB-10V
SDF-S-10H
SDF-KB-10H
SDF-S-8
SDF-KB-8
SDF-S-10U
SDF-KB-10L
SDF-S-14U
SDF-KB-14U
SDP-S-10S
SDP-KB-10S
SDP-S-14
SDP-KB-14
50 •
60 • •
70 •
80 • • •1) • • • •
100 • • • • • • •
120 • • • • • •
140 • • • • • •
160 • • • • • •
180 • • • • • •
200 • • •1) •1) •1) •1)
220 • • •1) •1) •1) •1)
1) Delivery time upon request
Screw head style and type of drive
Design SDF-S-10V
SDF-KB-10V
SDF-S-10H
SDF-KB-10H
SDF-S-8
SDF-KB-8
SDF-S-10U
SDF-KB-10L
SDF-S-14U
SDF-KB-14U
SDP-S-10S
SDP-KB-10S
SDP-S-14
SDP-KB-14
Countersunk Head • • • • • • • •
Hexagon Head • • • • • •
T30 •
T40 • • • • • • • •
A/F 10 •
A/F 13 • • • •
A/F 17 • •
EJOT® Facade anchorsoverview
143
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT® Facade anchorsoverview
EJOT® Facade anchorsproduct key:
Approval ETA-10/0305 Z-21.2-589 Z-21.2-967
Type of Anchor SDF-10V SDF-10H SDF-8 SDF-10U SDF-10L SDF-14U SDP-10S SDP-14
Nominal drill diameter dnom / dD [mm] 10 10 8 10 10 14 10 14
Drill cut diameter dcut [mm] � 10.45 10.45 8.45 10.45 10.45 14.5 10.45 14.5
Drill hole depth h1 / t [mm] � 50 / 60 80 60 80 100 80 80 80
Embedment depth (concrete + masonry) hnom / hv [mm] � – 70 50 70 – 70 70 70
Embedment depth (concrete) hnom,1 / hv [mm] � 40 70 50 70 – 70 70 70
Embedment depth (masonry) hnom,2 / hv [mm] � 50 70 50 70 � 90 70 70 70
Hole diameter of component to be installed df [mm] 10.5 10.5 8.5 10.5 10.5 14.5 10.5 14.5
Building materials Standard SDF-10V SDF-10H SDF-8 SDF-10U SDF-10L SDF-14U SDP-10S SDP-14
Standard concrete DIN 1045 • • • • •
Solid brick � Mz 12 DIN 105 • • • • •
Vertically perforated bricks � Hlz 12 DIN 105-1 • • • •
Vertically perforated brick LHlz1) DIN 105-2 • • • •
Solid lime sand brick � KS 12 DIN 106 • • • • •
Perforated lime sand brick � KSL 6 DIN 106 • • • •
Slag brick 1) DIN 398 • • •
Lightweight concrete cavity block � HBL 2 DIN 18151 • • • •
Solid lightweight concrete bricks DIN 18152 • • • • •
Solid concrete brick1) DIN 18153 • • •
Concrete cavity block1) DIN 18153 • • •
External wall panels made of concrete � C 12/15 DIN 1045 • • • •
Porous lightweight concrete TGL • • • •
Porous concrete DIN 1053 / 4165 • •
Porous concrete Laußig/Parchim TGL • •1) Generally: pull-out test on the structure
Example 1:
SDF-S-10Vx80-V
SDF = facade screw anchor-S = countersunk head anchor with countersunk head screw-10 = anchor diameter in mmV = solid brickx80 = anchor length in mm-V = steel screw with Cr(VI)-free surface
Example 2:
SDF-KB-10Hx120-E
SDF = facade screw anchor-KB = collar � ange anchor with hexagon screw-10 = anchor diameter in mmH = hollow brickx120 = anchor length in mm-E = A4 stainless steel screw
144
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
Ø in mm
Anchorlength L
mm
Fixingthickness
t� x
(concrete)� mm
Fixingthickness t
� x
(masonry)� mm
PUPrice
€ / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 50 10 – 100 SDF-S-10Vx50-V 858005045010 60 20 10 100 SDF-S-10Vx60-V 858006045010 70 30 20 100 SDF-S-10Vx70-V 858007045010 80 40 30 100 SDF-S-10Vx80-V 858008045010 100 60 50 100 SDF-S-10Vx100-V 858010045010 120 80 70 100 SDF-S-10Vx120-V 858012045010 140 100 90 100 SDF-S-10Vx140-V 858014045010 160 120 110 100 SDF-S-10Vx160-V 858016045010 180 140 130 100 SDF-S-10Vx180-V 858018045010 200 160 150 100 SDF-S-10Vx200-V 858020045010 220 180 170 100 SDF-S-10Vx220-V 8580220450
EJOT®
Facade anchor SDF-S-10Vwith countersunk head
CHARACTERISTIC VALUESHole depth in concrete h
1,1 .................................... � 50 mm
Effective embedment depth in concrete hnom,1
......... � 40 mmHole depth in masonry h
1,2 .................................... � 60 mm
Effective embedment depth in masonry hnom,2
.......... � 50 mmDrill-hole diameter d
0 .............................................. 10 mm
Hole diameter of construction part to be installedAntrieb .................................. Innensechsrund / TORX® T40
CHARACTERISTIC VALUESTensile load N
Rk,p in concrete C12/15
Temperature range 30 °C / 50 °C ...................... 4,50 kNTemperature range 50 °C / 80 °C ...................... 4,00 kN
FRk
brick Mz 20-1,8, NF ......................................... 2,50 kNF
Rk solid lime sand brick KS 36, NF........................... 4,00 kN
FRk
solid lime sand brick KS 20, 8 DF ........................ 4,50 kNTransverse load V
Rk,s in concrete C12/15 at h
nom,1 = 40 mm
Anchor with steel screw .................................... 7,93 kNAnchor with stainless steel screw A4 .................. 9,12 kN
Transverse load VRk,s
at hnom,2
= 50 mmAnchor with steel screw .................................. 11,09 kNAnchor with stainless steel screw A4 ................ 12,94 kN
Side load MRk,s
at hnom,1
=40 mmAnchor with steel screw ................................. 13,80 NmAnchor with stainless steel screw A4 ............... 16,09 Nm
Side load MRk,s
at hnom,2
= 50 mmAnchor with steel screw ................................. 23,01 NmAnchor with stainless steel screw A4 ............... 26,62 Nm
PERMITTED LOAD*Tensile load N
per in concrete C12/15
Temperature range 30 °C / 50 °C ...................... 1,79 kNTemperature range 50 °C / 80 °C ...................... 1,59 kN
Brick Mz 20-1,8, NF .............................................. 0,71 kNSolid lime sand brick KS 36, NF ............................... 1,14 kNSolid lime sand brick KS 20, 8 DF ............................ 1,29 kNTransverse load V
per in concrete C12/15 at h
nom,1 = 40 mm
Anchor with steel screw .................................... 4,53 kNAnchor with stainless steel screw A4 .................. 4,18 kN
Transverse load Vper
at hnom,2
= 50 mmAnchor with steel screw .................................... 6,34 kNAnchor with stainless steel screw A4 .................. 5,92 kN
Max. permitted side load hnom,1
=40 mmAnchor with steel screw ....................................7,89 NmAnchor with stainless steel screw A4 ..................7,37 Nm
Max. permitted side load at hnom,2
= 50 mmAnchor with steel screw ................................. 13,15 NmAnchor with stainless steel screw A4 ............... 12,19 Nm
NOTESPlease note the European Technical Approval ETA-10/0305 in your planning and in the processing of the products. Further information about parameters and loads can be found in the approval.
*For calculation of the acceptable loading the material safety value �
M and the factoral load �
F = 1,4 were included.
FEATURES• Anchor with an embedment depth
of 40 mm in concrete• Two installation depths
(embedment in masonry 50 mm)• Very short expansion part, for short
installation times• Optimal expanding part due to radial expansion• Very high bending moment• Cr VI-free coating of the screw• Product identification through different sleeve
colours• Double safety lock against torsion for secure
installation
APPROVALETA-10/0305
INSTALLATION SUBSTRATEApproved for:• Concrete• Solid brick • Solid lime sand brick Solid lightweight concrete brickSuitable for:• Natural stone with compact structure• Plaster board
APPLICATION RANGE• Installation of wood or metal components • For all non-load carrying redundant systems according
to ETAG 020• Suitable for the structural fastening of gates, doors,
windows, square timber
Concrete Masonry
145
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
Ø in mm
Anchorlength L
mm
Fixingthickness
t� x
(concrete)� mm
Fixingthickness t
� x
(masonry)� mm
PUPrice
€ / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 50 10 – 100 SDF-KB-10Vx50-V 858105045010 60 20 10 100 SDF-KB-10Vx60-V 858106045010 70 30 20 100 SDF-KB-10Vx70-V 858107045010 80 40 30 100 SDF-KB-10Vx80-V 858108045010 100 60 50 100 SDF-KB-10Vx100-V 858110045010 120 80 70 100 SDF-KB-10Vx120-V 858112045010 140 100 90 100 SDF-KB-10Vx140-V 858114045010 160 120 110 100 SDF-KB-10Vx160-V 858116045010 180 140 130 100 SDF-KB-10Vx180-V 858118045010 200 160 150 100 SDF-KB-10Vx200-V 858120045010 220 180 170 100 SDF-KB-10Vx220-V 8581220450Anchor with A4 stainless steel screws (-E)10 50 10 – 100 SDF-KB-10Vx50-E 858105065010 60 20 10 100 SDF-KB-10Vx60-E 858106065010 70 30 20 100 SDF-KB-10Vx70-E 8581070650
EJOT®
Facade anchor SDF-KB-10Vwith hexagon head
CHARACTERISTIC VALUESHole depth in concrete h
1,1 .................................... � 50 mm
Effective embedment depth in concrete hnom,1
......... � 40 mmHole depth in masonry h
1,2 .................................... � 60 mm
Effective embedment depth in masonry hnom,2
.......... � 50 mmDrill-hole diameter d
0 .............................................. 10 mm
Hole diameter of construction part to be installedDrive .................. hexagon A/F13 + hexalobular / TORX® T40
CHARACTERISTIC VALUESTensile load N
Rk,p in concrete C12/15
Temperature range 30 °C / 50 °C ...................... 4,50 kNTemperature range 50 °C / 80 °C ...................... 4,00 kN
FRk
brick Mz 20-1,8, NF ......................................... 2,50 kNF
Rk solid lime sand brick KS 36, NF........................... 4,00 kN
FRk
solid lime sand brick KS 20, 8 DF ........................ 4,50 kNTransverse load V
Rk,s in concrete C12/15 at h
nom,1 = 40 mm
Anchor with steel screw .................................... 7,93 kNAnchor with stainless steel screw A4 .................. 9,12 kN
Transverse load VRk,s
at hnom,2
= 50 mmAnchor with steel screw .................................. 11,09 kNAnchor with stainless steel screw A4 ................ 12,94 kN
Bending moment MRk,s
at hnom,1
=40 mmAnchor with steel screw ................................. 13,80 NmAnchor with stainless steel screw A4 ............... 16,09 Nm
Side load MRk,s
at hnom,2
= 50 mmAnchor with steel screw ................................. 23,01 NmAnchor with stainless steel screw A4 ............... 26,62 Nm
PERMITTED LOAD*Tensile load N
per in concrete C12/15
Temperature range 30 °C / 50 °C ...................... 1,79 kNTemperature range 50 °C / 80 °C ...................... 1,59 kN
Brick Mz 20-1,8, NF .............................................. 0,71 kNSolid lime sand brick KS 36, NF ............................... 1,14 kNSolid lime sand brick KS 20, 8 DF ............................ 1,29 kNTransverse load V
per in concrete C12/15 at h
nom,1 = 40 mm
Anchor with steel screw .................................... 4,53 kNAnchor with stainless steel screw A4 .................. 4,18 kN
Transverse load Vper
at hnom,2
= 50 mmAnchor with steel screw .................................... 6,34 kNAnchor with stainless steel screw A4 .................. 5,92 kN
Max. permitted side load hnom,1
=40 mmAnchor with steel screw ....................................7,89 NmAnchor with stainless steel screw A4 ..................7,37 Nm
Max. permitted side load at hnom,2
= 50 mmAnchor with steel screw ................................. 13,15 NmAnchor with stainless steel screw A4 ............... 12,19 Nm
NOTESPlease note the European Technical Approval ETA-10/0305 in your planning and in the processing of the products. Further information about parameters and loads can be found in the approval.
*For calculation of the acceptable loading the material safety value �
M and the factoral load �
F = 1,4 were included.
APPLICATION RANGE• Installation of metal components • For all non-load carrying redundant systems according
to ETAG 020• Suitable for the structural fastening of wall cupboards,
cladding, metal angle pieces
h
h1,1hnom,1
t fix
tolt
h
h1,2hnom,2
t fix
tolt
Concrete Masonry
FEATURES• Anchor with an embedment depth
of 40 mm in concrete• Two installation depths
(embedment in masonry 50 mm)• Very short expansion part, for short
installation times• Optimal expanding part due to radial expansion• Very high bending moment• Cr VI-free coating of the screw• Product identification through different sleeve
colours• Double safety lock against torsion for secure
installation
APPROVALETA-10/0305
INSTALLATION SUBSTRATEApproved for:• Concrete• Solid brick • Solid lime sand brick Solid lightweight concrete brickSuitable for:• Natural stone with compact structure• Plaster board
146
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDF-S-10Hwith countersunk head
CHARACTERISTIC VALUESHole depth h
1 ...................................................... � 80 mm
Effective embedment depth hnom
........................... � 70 mmDrill-hole diameter d
0 ........................................... = 10 mm
Hole diameter of construction part to be installedDrive ............................................ hexalobular / TORX® T40
CHARACTERISTIC VALUESTensile load N
Rk,p in concrete C12/15
Temperature range 30 °C / 50 °C ............................ 4,50 kNTemperature range 50 °C / 80 °C ............................ 4,00 kNBrick Mz 20-1,8, NF .............................................. 4,00 kNSolid lime sand brick KS 36, NF ............................... 4,50 kNSolid lime sand brick KS 20, 8 DF ............................ 4,50 kNSolid lightweight concrete brick V6, 2 DF .................. 2,00 kNPorous lightweight concrete .................................... 2,00 kNVertically perforated brick HLz 12-0,9, NF ................ 2,00 kNPerforated lime sand brick KSL 12, 4 DF .................. 2,50 kNCavity block tile made of lightweight concrete Hbl 10, 12 DF .. 1,20 kNTransverse load V
Rk,s
Anchor with steel screw ......................................... 9,35 kNAnchor with stainless steel screw A4 ..................... 10,91 kNSide load M
Rk,s
Anchor with steel screw ...................................... 17,67 NmAnchor with stainless steel screw A4 .................... 20,62 Nm
PERMITTED LOAD*Tensile load N
per in concrete C12/15
Temperature range 30 °C / 50 °C ............................ 1,79 kNTemperature range 50 °C / 80 °C ............................ 1,59 kNBrick Mz 20-1,8, NF .............................................. 1,14 kNSolid lime sand brick KS 36, NF ............................... 1,29 kNSolid lime sand brick KS 20, 8 DF ............................ 1,29 kNSolid lightweight concrete brick V6, 2 DF .................. 0,57 kNPorous lightweight concrete .................................... 0,57 kNVertically perforated brick HLz 12-0,9, NF ................ 0,57 kNPerforated lime sand brick KSL 12, 4 DF .................. 0,71 kNCavity block tile made of lightweight concrete Hbl 10, 12 DF .. 0,34 kNTransverse load V
zul
Anchor with steel screw ......................................... 5,34 kNAnchor with stainless steel screw A4 ....................... 5,00 kNMax. permitted side load Anchor with steel screw ...................................... 10,10 NmAnchor with stainless steel screw A4 ...................... 9,44 Nm
NOTESFor planning and processing of the product please note the European Technical Approval ETA-10/0305. Further information about parameters and loads can be found in the approval.
*For the calculation of the acceptable loading the material safety value �
M and the factoral load �
F = 1,4 were included.
FEATURES• Approved for all common building materials• Reliable installation in problematic building
material due to optimised expansion part• Secure hold due to radial expansion• Cr VI-free coating of the screw• Product identification through different sleeve
colours• Double safety lock against torsion for secure
installation
APPROVALETA-10/0305
INSTALLATION SUBSTRATEApproved for:• Concrete• Solid brick• Solid lime sand brick• Solid lightweight concrete brick• Vertically perforated brick • Lightweight vertically perforated brick• Perforated lime sand brick• Lightweight concrete cavity block• Porous lightweight concrete Suitable for:• Natural stone• Plaster board• Non-classi� ed cavity and perforated brick
Ø mm
Anchorlength L
mm
Fixingthickness t
� x
� mmPU
Price € / 100
pcs.Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 80 10 100 SDF-S-10Hx80-V 851008042010 100 30 100 SDF-S-10Hx100-V 851010042010 120 50 100 SDF-S-10Hx120-V 851012042010 140 70 100 SDF-S-10Hx140-V 851014042010 160 90 100 SDF-S-10Hx160-V 851016042010 180 110 100 SDF-S-10Hx180-V 851018042010 200 130 100 SDF-S-10Hx200-V 851020042010 220 150 100 SDF-S-10Hx220-V 8510220420Anchor with A4 stainless steel screws (-E)10 80 10 100 SDF-S-10Hx80-E 851008062010 100 30 100 SDF-S-10Hx100-E 851010062010 120 50 100 SDF-S-10Hx120-E 851012062010 140 70 100 SDF-S-10Hx140-E 851014062010 160 90 100 SDF-S-10Hx160-E 851016062010 180 110 100 SDF-S-10Hx180-E 851018062010 200 130 100 SDF-S-10Hx200-E 851020062010 220 150 100 SDF-S-10Hx220-E 8510220620
hh1
nomh ttol
t fix
Installationsubstrate
APPLICATION RANGE• Installation of wood or metal components • For all non-load carrying redundant systems according
to ETAG 020• Suitable for the structural fastening of gates, doors,
windows, square timber• For installation in external wall panels made of concrete
147
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
Ø in mm
Anchorlength L
mm
Fixingthickness t
� x
� mmPU
Price € / 100
pcs.Order description Part number
Anchor with steel screw with zinc-plated Cr(VI)-free coating (-V)10 80 10 100 SDF-KB-10Hx80-V 851308042010 100 30 100 SDF-KB-10Hx100-V 851310042010 120 50 100 SDF-KB-10Hx120-V 851312042010 140 70 100 SDF-KB-10Hx140-V 851314042010 160 90 100 SDF-KB-10Hx160-V 851316042010 180 110 100 SDF-KB-10Hx180-V 851318042010 200 130 100 SDF-KB-10Hx200-V 851320042010 220 150 100 SDF-KB-10Hx220-V 8513220420Anchor with A4 stainless steel screws (-E)10 80 10 100 SDF-KB-10Hx80-E 851308062010 100 30 100 SDF-KB-10Hx100-E 851310062010 120 50 100 SDF-KB-10Hx120-E 851312062010 140 70 100 SDF-KB-10Hx140-E 851314062010 160 90 100 SDF-KB-10Hx160-E 851316062010 180 110 100 SDF-KB-10Hx180-E 851318062010 200 130 100 SDF-KB-10Hx200-E 851320062010 220 150 100 SDF-KB-10Hx220-E 8513220620
Installationsubstrate
APPLICATION RANGE• Installation of metal components • For all non-load carrying redundant systems according
to ETAG 020• Suitable for the structural fastening of wall cupboards,
cladding, metal angle pieces• For installation in external wall panels made of concrete
EJOT®
Facade anchor SDF-KB-10Hwith hexagon head
CHARACTERISTIC VALUESHole depth h
1 ...................................................... � 80 mm
Effective embedment depth hnom
........................... � 70 mmDrill-hole diameter d
0 ........................................... = 10 mm
Hole diameter of construction part to be installedDrive .................... hexagon A/F13 + hexalobular TORX® T40
CHARACTERISTIC VALUESTensile load N
Rk,p in concrete C12/15
Temperature range 30 °C / 50 °C ............................ 4,50 kNTemperature range 50 °C / 80 °C ............................ 4,00 kNBrick Mz 20-1,8, NF .............................................. 4,00 kNSolid lime sand brick KS 36, NF ............................... 4,50 kNSolid lime sand brick KS 20, 8 DF ............................ 4,50 kNSolid lightweight concrete brick V6, 2 DF .................. 2,00 kNPorous lightweight concrete .................................... 2,00 kNVertically perforated brick HLz 12-0,9, NF ................ 2,00 kNPerforated lime sand brick KSL 12, 4 DF .................. 2,50 kNCavity block tile made of lightweight concrete Hbl 10, 12 DF .. 1,20 kNTransverse load V
Rk,s
Anchor with steel screw ......................................... 9,35 kNAnchor with stainless steel screw A4 ..................... 10,91 kNSide load M
Rk,s
Anchor with steel screw ...................................... 17,67 NmAnchor with stainless steel screw A4 .................... 20,62 Nm
PERMITTED LOAD*Tensile load N
per in concrete C12/15
Temperature range 30 °C / 50 °C ............................ 1,79 kNTemperature range 50 °C / 80 °C ............................ 1,59 kNBrick Mz 20-1,8, NF .............................................. 1,14 kNSolid lime sand brick KS 36, NF ............................... 1,29 kNSolid lime sand brick KS 20, 8 DF ............................ 1,29 kNSolid lightweight concrete brick V6, 2 DF .................. 0,57 kNPorous lightweight concrete .................................... 0,57 kNVertically perforated brick HLz 12-0,9, NF ................ 0,57 kNPerforated lime sand brick KSL 12, 4 DF .................. 0,71 kNCavity block tile made of lightweight concrete Hbl 10, 12 DF .. 0,34 kNTransverse load V
zul
Anchor with steel screw ......................................... 5,34 kNAnchor with stainless steel screw A4 ....................... 5,00 kNMax. permitted side load Anchor with steel screw ...................................... 10,10 NmAnchor with stainless steel screw A4 ...................... 9,44 Nm
NOTESFor planning and processing of the product please note the European Technical Approval ETA-10/0305. Further information about parameters and loads can be found in the approval.
*For the calculation of the acceptable loading the material safety value �
M and the factoral load �
F = 1,4 were included.
FEATURES• Approved for all common building materials• Reliable installation in problematic building
material due to optimised expansion part• Secure hold due to radial expansion• Cr VI-free coating of the screw• Product identification through different sleeve
colours• Double safety lock against torsion for secure
installation
APPROVALETA-10/0305
INSTALLATION SUBSTRATEApproved for:• Concrete• Solid brick• Solid lime sand brick• Solid lightweight concrete brick• Vertically perforated brick • Lightweight vertically perforated brick• Perforated lime sand brick• Lightweight concrete cavity block• Porous lightweight concrete Suitable for:• Natural stone• Plaster board• Non-classi� ed cavity and perforated brick
148
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDF-S-8with countersunk head
APPLICATION RANGE• For � xing timber substructures
to solid brick masonry and concrete• For installation in external wall panels made of concrete
FEATURES• Small drill-hole diameter• Cr(VI)-free coating• Product identification through different sleeve colours
APPROVALZ-21.2-589
CHARACTERISTIC VALUESDrive .............................................hexalobular / TORX® T30 Hole depth � t ....................................................... 60 mmEmbedment depth � h
v .......................................... 50 mm
PERMITTED LOADSConcrete � C12/15 ................................................. 0.5 kNSolid brick � Mz 12 .................................................. 0.4 kNUnperforated solid brick � Mz 12 .............................. 0.5 kNSand-lime solid brick � KS 12 ................................... 0.4 kNUnperforated sand-lime solid brick � KS 12 ............... 0.5 kNLight-weight solid brick � V 2.................................. 0.15 kNExternal wall panels made of concrete � C12/15 ...... 0.25 kNMaximum allowable bending moment steel ............... 4,7 NmMaximum allowable bending moment stainless steel .. 5,3 Nm
NOTEFor planning and processing please note approval Z-21-2-589
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100
pcs.Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)8 80 30 100 SDF-S-8x80-V 85668804038 100 50 100 SDF-S-8x100-V 85668104038 120 70 100 SDF-S-8x120-V 85668124038 140 90 100 SDF-S-8x140-V 85668144038 160 110 100 SDF-S-8x160-V 85668164038 180 130 100 SDF-S-8x180-V 85668184038 200 150 100 SDF-S-8x200-V* 85668204038 220 170 100 SDF-S-8x220-V* 8566822403Anchor with A4 stainless steel screws (-E)8 80 30 100 SDF-S-8x80-E* 85668806068 100 50 100 SDF-S-8x100-E 85668106068 120 70 100 SDF-S-8x120-E 85668126068 140 90 100 SDF-S-8x140-E 85668146068 160 110 100 SDF-S-8x160-E 85668166068 180 130 100 SDF-S-8x180-E 85668186068 200 150 100 SDF-S-8x200-E* 85668206068 220 170 100 SDF-S-8x220-E* 8566822606* Delivery time upon request
149
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDF-KB-8with hexagon head
APPLICATION RANGE• For � xing metal substructures
to solid brick masonry and concrete• For installation in external wall panels made of concrete
FEATURES• Hexagon head with flange• Small drill-hole diameter• Cr(VI)-free coating• Thermal and galvanic separation• Product identification through different sleeve colours
APPROVALZ-21.2-589
CHARACTERISTIC VALUESDrive .......................................................... hexagon A/F10 Hole depth � t ....................................................... 60 mmEmbedment depth � h
v .......................................... 50 mm
PERMITTED LOADSConcrete � C12/15 ................................................. 0.5 kNSolid brick � Mz 12 .................................................. 0.4 kNUnperforated solid brick � Mz 12 .............................. 0.5 kNSand-lime solid brick � KS 12 ................................... 0.4 kNUnperforated sand-lime solid brick � KS 12 ............... 0.5 kNLight-weight solid brick � V 2.................................. 0.15 kNExternal wall panels made of concrete � C12/15 ...... 0.25 kNMaximum allowable bending moment steel ............... 4,7 NmMaximum allowable bending moment stainless steel .. 5,3 Nm
NOTEFor planning and processing please note approval Z-21-2-589
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)8 60 10 100 SDF-KB-8x60-V 87478605128 80 30 100 SDF-KB-8x80-V 87478805128 100 50 100 SDF-KB-8x100-V 87478105128 120 70 100 SDF-KB-8x120-V 87478125128 140 90 100 SDF-KB-8x140-V 87478145128 160 110 100 SDF-KB-8x160-V 87478165128 180 130 100 SDF-KB-8x180-V 87478185128 200 150 100 SDF-KB-8x200-V* 87478205128 220 170 100 SDF-KB-8x220-V* 8747822512Anchor with A4 stainless steel screws (-E)8 60 10 100 SDF-KB-8x60-E 87478603108 80 30 100 SDF-KB-8x80-E 87478803108 100 50 100 SDF-KB-8x100-E 87478103108 120 70 100 SDF-KB-8x120-E 87478123108 140 90 100 SDF-KB-8x140-E 87478143108 160 110 100 SDF-KB-8x160-E 87478163108 180 130 100 SDF-KB-8x180-E 87478183108 200 150 100 SDF-KB-8x200-E* 87478203108 220 170 100 SDF-KB-8x220-E* 8747822310* Delivery time upon request
150
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT® Universalfacade anchor SDF-S-10U
with countersunk head
APPLICATION RANGE• For � xing timber substructures
to perforated brick, solid brick masonry and concrete• For � xing in external wall panels made of concrete and
porous lightweight concrete
FEATURES• High bending moment• High loads• Cr(VI)-free coating• Embedment in all standard building materials• Product identification through different sleeve colours
APPROVALZ-21.2-589
CHARACTERISTIC VALUESDrive ............................................ hexalobular / TORX® T40 Hole depth � t ........................................................ 80 mmEmbedment depth � h
v ........................................... 70 mm
PERMITTED LOADSConcrete � C12/15 ................................................. 1.6 kNSolid brick � Mz 12 .................................................. 0.6 kNUnperforated solid brick � Mz 12 .............................. 0.8 kNSand-lime solid brick � KS 12 ................................... 0.6 kNUnperforated sand-lime solid brick � KS 12 ............... 0.8 kNVertically perforated brick � Hlz 12 ............................ 0.5 kNSand-lime perforated brick � KSL 6 ........................... 0.4 kNLight-weight cavity block � Hbl 2 ............................ 0.25 kNLight-weight solid brick � V 2.................................. 0.25 kNExternal wall panels made of concrete � C12/15 ........ 0.6 kNPorous lightweight concrete (h
v � 90 mm) .................. 0.3 kN
Maximum allowable bending moment steel ..............11,5 NmMaximum allowable bending moment stainless steel .13,0 Nm
NOTEFor planning and processing please note approval Z-21-2-589
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
NOTEAn additional large diameter washer acc. to DIN 9021 must be used for fastening metal parts.
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100
pcs.Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 250 180 100 SDF-S-10Ux250-V 872325041310 275 205 100 SDF-S-10Ux275-V 872327541310 300 230 100 SDF-S-10Ux300-V 8723300413
151
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100
pcs.Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 120 30 100 SDF-KB-10Lx120-V 8755120602
EJOT®
Facade anchor SDF-KB-10Lwith hexagon head
APPLICATION RANGE• For fixing metal substructure
to perforated brick• For fixing in external wall panels made of concrete and
porous lightweight concrete
FEATURES• Hexagon head with flange• Large percentage contact area in vertically perforated
brick• High bending moment• Cr VI-free surface• Thermal and galvanic separation• Product identification through different sleeve colours
APPROVALZ-21.2-589
CHARACTERISTIC VALUESDrive .......................................................... hexagon A/F13Hole depth � t ...................................................... 100 mmEmbedment depth � hv ........................................... 90 mm
PERMITTED LOADSVertically perforated brick � Hlz 12 ............................ 0.3 kNSand-lime perforated brick � KSL 6 ........................... 0.4 kNLight-weight cavity block � Hbl 2 ............................ 0.25 kNLight-weight solid brick � V 2.................................. 0.25 kNExternal wall panels made of concrete � C12/15 .........0.4 kNPorous lightweight concrete (hv � 90 mm) ................. 0.5 kN Maximum allowable bending moment steel ..............11,5 NmMaximum allowable bending moment stainless steel .13,0 Nm
NOTEFor planning and processing please note approval Z-21-2-589
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
152
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT® Universalfacade anchor SDF-S-14U
with countersunk head
APPLICATION RANGE• For fixing timber substructure
to perforated brick, solid brick masonry and concrete• For embedment in porous lightweight concrete
FEATURES• Optimum security against torsion• Cr(VI)-free coating• High load-carrying capacity• Product identification through different sleeve colours
APPROVALZ-21.2-589
CHARACTERISTIC VALUESDrive ............................................ hexalobular / TORX® T40 Hole depth � t ........................................................ 80 mmEmbedment depth � h
v ........................................... 70 mm
PERMITTED LOADSConcrete � C12/15 ................................................. 1.8 kNSolid brick � Mz 12 .................................................. 0.6 kNUnperforated solid brick � Mz 12 .............................. 0.8 kNSand-lime solid brick � KS 12 ................................... 0.6 kNUnperforated sand-lime solid brick � KS 12 ............... 0.8 kNVertically perforated brick � Hlz 12 ............................ 0.5 kNSand-lime perforated brick � KSL 6 ........................... 0.6 kNLight-weight cavity block � Hbl 2 .............................. 0.3 kNLight-weight solid brick � V 2.................................... 0.5 kNPorous lightweight concrete (h
v � 90 mm) .................. 0.7 kN
Maximum allowable bending moment steel ............. 26,3 NmMaximum allowable bending moment stainless steel 24,7 Nm
NOTEFor planning and processing please note approval Z-21-2-589
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)14 120 50 50 SDF-S-14Ux120-V 870712045314 140 70 50 SDF-S-14Ux140-V 870714045314 180 110 50 SDF-S-14Ux180-V 870718045314 220 150 50 SDF-S-14Ux220-V 870722045314 260 190 50 SDF-S-14Ux260-V 870726045314 300 230 50 SDF-S-14Ux300-V 870730045314 360 290 50 SDF-S-14Ux360-V 8707360453
NOTEAn additional large diameter washer acc. to DIN 9021 must be used for fastening metal parts.
153
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT® Universalfacade anchor SDF-KB-14Uwith hexagon head
APPLICATION RANGE• For fixing metal substructures
in perforated brick, solid brick masonry and concrete• For embedment in porous lightweight concrete
FEATURES• Hexagon head with flange• Optimum security against torsion• Cr(VI)-free coating• High load-carrying capacity• Product identification through different sleeve colours
APPROVALZ-21.2-589
CHARACTERISTIC VALUESDrive .......................................................... hexagon A/F17 Hole depth � t ........................................................ 80 mmEmbedment depth � h
v ........................................... 70 mm
PERMITTED LOADSConcrete � C12/15 ................................................. 1.8 kNSolid brick � Mz 12 .................................................. 0.6 kNUnperforated solid brick � Mz 12 .............................. 0.8 kNSand-lime solid brick � KS 12 ................................... 0.6 kNUnperforated sand-lime solid brick � KS 12 ............... 0.8 kNVertically perforated brick � Hlz 12 ............................ 0.5 kNSand-lime perforated brick � KSL 6 ........................... 0.6 kNLight-weight cavity block � Hbl 2 .............................. 0.3 kNLight-weight solid brick � V 2.................................... 0.5 kNPorous lightweight concrete (h
v � 90 mm) .................. 0.7 kN
Maximum allowable bending moment steel ............. 26,3 NmMaximum allowable bending moment stainless steel 24,7 Nm
NOTEFor planning and processing please note approval Z-21-2-589
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)14 80 10 50 SDF-KB-14Ux80-V 874008060214 100 30 50 SDF-KB-14Ux100-V 8740100602
154
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDP-S-10Swith countersunk head
APPLICATION RANGE• For � xing timber substructure
to aerated concrete• For � xing timber substructure
to aerated concrete from Laußig and Parchim
FEATURES• Reliable form-fit due to combined expansion zones• Cr(VI)-free coating• Fast rotary hole drilling• Product identification through different sleeve colours• High anchoring stability even into soft aerated concrete
APPROVALZ-21.2-967
CHARACTERISTIC VALUESDrive .............................................hexalobular / TORX® T40 Hole depth � t ....................................................... 80 mmEmbedment depth � hv .......................................... 70 mm
PERMITTED LOADSAerated concrete PP2 / P3,3 acc. to DIN .................... 0.3 kNAerated concrete � PP4 / P4,4 acc. to DIN ................. 0.6 kNAerated concrete in accordance with TGL Werk Laußig 0.4 kNAerated concrete in accordance with TGL Werk Parchim; 0.2 kNMaximum allowable bending moment steel ..............11,5 NmMaximum allowable bending moment stainless steel .13,0 Nm
NOTEFor planning and processing please note approval Z-21-2-967
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 80 10 100 SDP-S-10Sx80-V 877408042310 100 30 100 SDP-S-10Sx100-V 877410042310 120 50 100 SDP-S-10Sx120-V 877412042310 140 70 100 SDP-S-10Sx140-V 877414042310 160 90 100 SDP-S-10Sx160-V 877416042310 180 110 100 SDP-S-10Sx180-V 877418042310 200 130 100 SDP-S-10Sx200-V* 877420042310 220 150 100 SDP-S-10Sx220-V* 8774220423Anchor with A4 stainless steel screws (-E)10 80 10 100 SDP-S-10Sx80-E 877408062310 100 30 100 SDP-S-10Sx100-E 877410062310 120 50 100 SDP-S-10Sx120-E 877412062310 140 70 100 SDP-S-10Sx140-E 877414062310 160 90 100 SDP-S-10Sx160-E 877416062310 180 110 100 SDP-S-10Sx180-E 877418062310 200 130 100 SDP-S-10Sx200-E* 877420062310 220 150 100 SDP-S-10Sx220-E* 8774220623* Delivery time upon request
155
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDP-KB-10Swith hexagon head
APPLICATION RANGE• For � xing metal substructures
to aerated concrete• For � xing metal substructures to aerated concrete from
Laußig and Parchim
FEATURES• Hexagon head with flange• Reliable form-fit due to combined expansion zones• high anchoring stability even into soft gas concrete• Cr(VI)-free coating• Thermal and galvanic separation• Product identification through different sleeve colours• Fast rotary hole drilling
APPROVALZ-21.2-967
CHARACTERISTIC VALUESDrive .......................................................... hexagon A/F13Hole depth � t ........................................................ 80 mmEmbedment depth � h
v ........................................... 70 mm
PERMITTED LOADSAerated concrete PP2 / P3,3 acc. to DIN .................... 0.3 kNAerated concrete � PP4 / P4,4 acc. to DIN ................. 0.6 kNAerated concrete in accordance with TGL Werk Laußig 0.4 kNAerated concrete in accordance with TGL Werk Parchim; 0.2 kNMaximum allowable bending moment steel ..............11,5 NmMaximum allowable bending moment stainless steel .13,0 Nm
NOTEFor planning and processing please note approval Z-21-2-967
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)10 80 10 100 SDP-KB-10Sx80-V 877308060210 100 30 100 SDP-KB-10Sx100-V 877310060210 120 50 100 SDP-KB-10Sx120-V 877312060210 140 70 100 SDP-KB-10Sx140-V 877314060210 160 90 100 SDP-KB-10Sx160-V 877316060210 180 110 100 SDP-KB-10Sx180-V 877318060210 200 130 100 SDP-KB-10Sx200-V* 877320060210 220 150 100 SDP-KB-10Sx220-V* 8773220602Anchor with A4 stainless steel screws (-E)10 80 10 100 SDP-KB-10Sx80-E 877308031010 100 30 100 SDP-KB-10Sx100-E 877310031010 120 50 100 SDP-KB-10Sx120-E 877312031010 140 70 100 SDP-KB-10Sx140-E 877314031010 160 90 100 SDP-KB-10Sx160-E 877316031010 180 110 100 SDP-KB-10Sx180-E 877318031010 200 130 100 SDP-KB-10Sx200-E* 877320031010 220 150 100 SDP-KB-10Sx220-E* 8773220310* Delivery time upon request
156
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDP-S-14with countersunk head
APPLICATION RANGE• For � xing timber substructure to aerated concrete• For � xing timber substructure
to aerated concrete from Laußig and Parchim
FEATURES• Very robust• Easy and quick installation• Cr(VI)-free coating• Thermal and galvanic separation• Product identification through different sleeve colours• High bending moment• Fast rotary hole drilling• High embedment stability even in soft gas concrete
APPROVALZ-21.2-967
CHARACTERISTIC VALUESDrive ............................................ hexalobular / TORX® T40 Hole depth � t ....................................................... 80 mmEmbedment depth � h
v .......................................... 70 mm
PERMITTED LOADSAerated concrete PP2 / P3,3 acc. to DIN .................... 0.4 kN Aerated concrete � PP4 / P4,4 acc. to DIN ................. 0.8 kNAerated concrete in accordance with TGL Werk Laußig 0.5 kNAerated concrete in accordance with TGL Werk Parchim . 0.3 kNMaximum allowable bending moment steel ............. 26,3 NmMaximum allowable bending moment stainless steel 24,7 Nm
NOTEFor planning and processing please note approval Z-21-2-967
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)14 120 50 50 SDP-S-14x120-V 877012051214 140 70 50 SDP-S-14x140-V 877014051214 180 110 50 SDP-S-14x180-V 877018051214 220 150 50 SDP-S-14x220-V 8770220512
157
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
F a c a d e a n c h o r s
EJOT®
Facade anchor SDP-KB-14with hexagon head
APPLICATION RANGE• For � xing metal substructure to aerated concrete• For � xing metal substructures to gas concrete from
Laußig and Parchim
FEATURES• Hexagon head with flange• Very robust• Easy and quick installation• Cr(VI)-free coating• Thermal and galvanic separation• Product identification through different sleeve colours• High bending moment• Fast rotary hole drilling• High embedment stability even in soft gas concrete
APPROVALZ-21.2-967
CHARACTERISTIC VALUESDrive .......................................................... hexagon A/F17 Hole depth � t ....................................................... 80 mmEmbedment depth � h
v .......................................... 70 mm
PERMITTED LOADSGas concrete PP2 / P3,3 acc. to DIN .......................... 0.4 kN Gas concrete � PP4 / P4,4 acc. to DIN ....................... 0.8 kNGas concrete in accordance with TGL Werk Laußig ...... 0.5 kNGas concrete in accordance with TGL Werk Parchim .... 0.3 kNMaximum allowable bending moment steel ............. 26,3 NmMaximum allowable bending moment stainless steel 24,7 Nm
NOTEFor planning and processing please note approval Z-21-2-967
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
Ø mm
Anchorlength L
mm
Fixingthickness B
� mmPU
Price € / 100 pcs.
Order description Part number
Anchor with zinc-plated steel screw, Cr(VI)-free coating (-V)14 80 10 50 SDP-KB-14x80-V* 876908060214 100 30 50 SDP-KB-14x100-V* 8769100602Anchor with A4 stainless steel screws (-E)14 80 10 50 SDP-KB-14x80-E* 876908031014 100 30 50 SDP-KB-14x100-E* 8769100310* Delivery time upon request
158
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A n c h o r s a n d E m b e d m e n t T e c h n o l o g yN o t e s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
© EJOT Spojna Tehnika d.o.o. AVAZ TWIST TOWER, SARAJEVO, BOSNIA AND HERZEGOVINA Supplied by EJOT: EJOT® SAPHIR self-drilling screw JT2, EJOT® facade anchor
159
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
S t e e l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anchor bolt S-KA and S-KAH
FEATURES• Time-saving push through installation• Approved for embedment in cracked and non-cracked
concrete• High permissible loads with small centre and edge
distance • Reliable hold in cracked concrete facilitates controlled
expansion• European Technical Approval, option 1• Tested for � re resistance
APPLICATIONEmbedment of • Anchor plates• Cable routes• Steel girder• Steel columns• Wooden structures• Balcony railings• Heavy suspended ceilings
APPROVALETA-08/0173
USE OF THE MATERIAL
Application rangeS-KA S-KAH S-KAH HCR
Zinc-plated steel A4 stainless steel HCR (1.4529)Dry indoor use • • •Wet indoor use • •Indoor swimming pools •Auto tunnels •
INSTALLATION INSTRUCTION
160
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
S t e e l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anchor bolt S-KAZinc-plated steel
APPLICATION RANGE• For embedment in cracked and non-cracked
concrete � C20/25
FEATURES• Zinc-plated steel• Approval for concrete, option I • Fire-resistance classes F30, F60, F90, F120
APPROVALETA-08/0173
NOTECharacteristic values apply to the compression strength of C20/25 concrete. Design load of an anchor for central tension in cracked concrete.
CROSS REFERENCEBlow-out pump ........................................ page 190
Type of anchor
Design load Fper [kN]
Centre distance mm Edge distance mm
Scr, N S min C Ccr, N C min S
S-KA 8 2.0 135 50 50 68 50 50S-KA 10 3.6 180 55 80 90 50 100S-KA 12 4.8 210 60 90 105 55 145S-KA 16 9.5 255 70 120 128 85 150
Type of anchor
Permissible bending moment [Nm]
Clamp load MD [Nm]
S-KA 8 10.0 20S-KA 10 22.9 35S-KA 12 34.3 50S-KA 16 88.6 120
Ø in mm
Length L mm
Fixingthick-
ness B� mm
Hole depth h1
� mm
Embed-ment
depth hef � mm
PUPrice
€ / 100 pcs.
Order description Part number
S-KA 88 72 10 60 45 50 S-KA 8/10-V 96500011128 92 30 60 45 50 S-KA 8/30-V 96500011148 112 50 60 45 40 S-KA 8/50-V 96500011168 147 85 60 45 40 S-KA 8/85-V 9650001118S-KA 1010 92 10 75 60 40 S-KA 10/10-V 965000113210 102 20 75 60 25 S-KA 10/20-V 965000113510 112 30 75 60 25 S-KA 10/30-V 965000113610 132 50 75 60 25 S-KA 10/50-V 965000113710 162 80 75 60 25 S-KA 10/80-V 9650001139S-KA 1212 103 5 90 70 20 S-KA 12/5-V 965000115012 118 20 90 70 20 S-KA 12/20-V 965000115212 128 30 90 70 20 S-KA 12/30-V 965000115312 163 65 90 70 20 S-KA 12/65-V 965000115512 178 80 90 70 20 S-KA 12/80-V 9650001157S-KA 1616 123 5 110 85 10 S-KA 16/5-V 965000117016 138 20 110 85 10 S-KA 16/20-V 965000117116 168 50 110 85 10 S-KA 16/50-V 9650001173S-KA 2020* 170 20 130 110 5 S-KA 20/20-V 965000118020* 220 70 130 110 5 S-KA 20/70-V 9650001182
Order information: Further lengths upon request.*Not part of the ETA
161
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
S t e e l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Anchor bolt S-KAHA4 stainless steel
APPLICATION RANGE• For embedment in cracked and non-cracked
concrete � C20/25• HCR (1.4529) anchor for embedment in chlorinated
atmosphere available upon request
FEATURES• A4 stainless steel• Approval for concrete, option I • Fire-resistance classes F30, F60, F90, F120
APPROVALETA-08/0173
NOTECharacteristic values apply to the compression strength of C20/25 concrete. Design load of an anchor for central tension in cracked concrete.
CROSS REFERENCEBlow-out pump ........................................ page 190
Ø in mm
Length L mm
Fixingthick-
ness B� mm
Hole depth h1
� mm
Embed-ment
depth hef � mm
PUPrice
€ / 100 pcs.
Order description Part number
S-KAH 66* 65 15 50 35 100 S-KAH 6/15-E 9650004102S-KAH 88 72 10 60 45 50 S-KAH 8/10-E 96500051128 112 50 60 45 40 S-KAH 8/50-E 9650004110S-KAH 1010 92 10 75 60 40 S-KAH 10/10-E 965000513210 112 30 75 60 25 S-KAH 10/30-E 965000513610 132 50 75 60 25 S-KAH 10/50-E 9650005138S-KAH 1212 103 5 90 70 20 S-KAH 12/5-E 965000515012 118 20 90 70 20 S-KAH 12/20-E 965000515212 128 30 90 70 20 S-KAH 12/30-E 9650005154S-KAH 1616 168 50 110 85 10 S-KAH 16/50-E 9650005172
Order information: Further lengths upon request.*Not part of the ETA
Type of anchor
Design load Fper [kN]
Centre distance mm Edge distance mm
Scr, N S min C Ccr, N C min S
S-KAH 8 2.0 135 50 50 68 50 50S-KAH 10 3.6 180 55 80 90 50 100S-KAH 12 4.8 210 60 90 105 55 145S-KAH 16 9.5 255 70 120 128 85 150
Type of anchor
Permissible bending moment [Nm]
Clamp load MD [Nm]
S-KAH 8 10.5 20S-KAH 10 21.4 35S-KAH 12 37.6 70S-KAH 16 95.2 120
162
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
N a i l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
EJOT®
Nail anchor ND-K -6with collar head
APPLICATION RANGE• For easy and quick installation• For light and constructional fastening
FEATURES• Zinc-plated steel• With pre-assembled special nail• For all pressure-resistant building materials• Easy to remove
RECOMMENDED WORK LOADHole depth � t ....................................................... 40 mmEmbedment depth h
v .............................................. 30 mm
RECOMMENDED WORK LOADConcrete ................................................................. 0.3 kNSolid brick ............................................................. 0.25 kNPerforated brick ..................................................... 0.25 kN
EJOT®
Nail anchor ND-K -8with collar head
APPLICATION RANGE• For easy and quick installation• For light and constructional fastening
FEATURES• Zinc-plated steel• With pre-assembled special nail• For all pressure-resistant building materials• Easy to remove
RECOMMENDED WORK LOADHole depth � t ....................................................... 55 mmEmbedment depth h
v .............................................. 45 mm
RECOMMENDED WORK LOADConcrete ............................................................... 0.40 kNSolid brick ............................................................. 0.30 kNPerforated brick ..................................................... 0.30 kN
Ømm
Anchor length L
mm
Clamping thickness B
� mmPU
Price €/100 pcs.
Order description Part number
6 35 5 100 ND-K-6x35 85616354006 45 15 100 ND-K-6x45 85616454006 55 25 100 ND-K-6x55 8561655400
6 70 40 100 ND-K-6x70 8561670400
Ømm
Anchor length L
mm
Clamping thickness B
� mmPU
Price €/100 pcs.
Order description Part number
8 60 15 50 ND-K-8x60 85618604008 75 35 50 ND-K-8x75 8561875400
8 100 55 50 ND-K-8x100 8561800400
163
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
I n s u l a t i o n s u p p o r t a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
EJOT®
Insulation support anchor DH
APPLICATION RANGE• For � xing soft insulating materials in the rear ventilated
facade.
FEATURES• High-grade plastic material• Easy installation with no additional expansion element• All-purpose for all building materials• Flexible stress plate reduces "quilt effect"
CHARACTERISTIC VALUESDrill bit diameter ....................................................... 8 mmHole depth � t ........................................................ 40 mmConcrete embedment depth � h
v .............................. 20 mm
Masonry embedment depth = hv .............................. 40 mm
Stress plate diameter .............................................. 90 mm
NOTEThe EJOT® insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. For soft insulation, such as rock or mineral wool, it needs to be considered that the plate diameter is at least 80 mm.The insulation board fastening is carried-out according to DIN 18516-1.
Ømm
Anchor length L
mm
Insulation thickness B
(masonry) � mm
Insulation thickness B
(concrete) � mm
PUPrice €/
100 pieces
Order description Part number
8 60 20 40 350 DH-8x60 85519060098 80 40 60 300 DH-8x80 85519080098 100 60 80 250 DH-8x100 85519100908 120 80 100 250 DH-8x120 85519120098 140 100 120 200 DH-8x140 85519140008 160 120 140 150 DH-8x160 85519160098 180 140 160 150 DH-8x180 85519180098 200 160 180 100 DH-8x200 85519200098 220 180 200 100 DH-8x220 8551922009
8 240 200 220 100 DH-8x240 8551924009
164
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
I n s u l a t i o n s u p p o r t a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
EJOT® Metal insulation stress plate DMT
for combination with DMH metal insulation support anchor
APPLICATION RANGE• For � xing soft insulating materials in combination with the
EJOT® DMH metal insulation support anchor • Fixing soft insulating materials for high � re protection
requirements
EJOT® Metal insulation support anchor DMH
APPLICATION RANGE• For fastening hard insulating materials in combination
with the EJOT® DMT metal insulation stress plate and also for soft insulating materials.
• Fixing insulating materials for high � re protection requirements (cellar ceiling insulation, insulation close to escape routes)
FEATURES• Easy installation by striking in, self-expanding• No pre-drilling required for aerated concrete• Easy installation
CHARACTERISTIC VALUESDrill bit diameter ....................................................... 8 mmHole depth � t ........................................................ 60 mmEmbedment depth h
v ............................................... 50 mm
Stress plate diameter .............................................. 35 mm
NOTEThe EJOT® insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. For soft insulation, such as rock or mineral wool, it needs to be considered that the plate diameter is at least 80 mm.The insulation board fastening is carried-out according to DIN 18516-1.
Ømm
Anchor length L mm
Insulation thickness B �
mmPU
Price €/ 100 pieces
Order description Part number
Alu-zinc steel8 80 30 250 DMH-8x80-V 97000303018 110 60 250 DMH-8x110-V 97000306028 140 90 250 DMH-8x140-V 97000306038 170 120 250 DMH-8x170-V 97000309128 200 150 250 DMH-8x200-V 97000312158 250 200 200 DMH-8x250-V 97000315208 300 250 200 DMH-8x300-V 9700031300A2 stainless steel8 80 30 250 DMH-8x80-E 97000303028 110 60 250 DMH-8x110-E 97000336038 140 90 250 DMH-8x140-E 97000369048 170 120 250 DMH-8x170-E 97000359128 200 150 250 DMH-8x200-E 97000352158 250 200 200 DMH-8x250-E 9700035520
8 300 250 200 DMH-8x300-E 9700035300
Ømm
PUPrice €/
100 piecesOrder description Part number
Alu-zinc steel80 250 DMT-80-V 9700030156A2 stainless steel80 250 DMT-80-E 9700030157
165
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
C h e m i c a l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
EJOT® Chemical anchors
APPLICATION RANGEAn expansion-pressure free embedment with building authorities approval for concrete, solid, perforated and hollow brick. These systems can be used for embedment of anchor rods and reinforcing steel rods.The expansion-pressure free assembly, provides an ideal hold in perforated and hollow bricks. It also guarantees reliable embedment near edges. The injection systems offer � exibility due to removable joints.
FEATURES• Upon request all products styrene and phtalate-free,
without solvents (= environment-friendly)• Economical use through optimal utilisation of the
cartridge content• Re-usable with a new mixer jet after work interruptions
APPROVALZ-21.3-1815Z-21.3-1816ETA-10/0134
CROSS REFERENCEBlow-out pump ........................................ page 190
Installation tools ...................................... page 169
MasonryThe temperature in the embedment area may amount to +50°C, temporarily +80°C
ConcreteThe temperature in the embedment area may amount to +40°C, temporarily +80°C
Temperature Processing time Curing time°C Polyester Vinylester Polyester Vinylester-10 - 90 min - 24 h-5 - 90 min - 14 h0 - 45 min - 7 h
+5 25 min 25 min 120 min 120 min+10 15 min 15 min 80 min 80 min+20 6 min 6 min 45 min 45 min+30 4 min 4 min 25 min 25 min+35 2 min 2 min 20 min 20 min
PROCESSING AND CURING TIMES (dry substrate)
The temperature referes to the substrate
Anchor rods Mperm.
in Nm Ø
Zinc-plated steel 5.8 A4 stainless steelM 8 10.7 12.1M 10 21.4 24.1 / 23.8*M 12 37.4 42.1M 16 95.1 106.7
Bending moment
*acc. to ETAG 06/0068 embedment in concrete
Stone format Maximum loadsw/o extra load Fperm.kN
w. extra load perm.kN
� 3 DF 1.0 1.44 to 10 DF 1.4 1.7� 10 DF 2.0 2.5
Substrate Permitted loadsmax. F
perm.
kNmax. F
perm.
kNSolid brick � Mz 12 1.7Solid lime sand brick � KS 12 1.7Vertically perforated brick � HLz 4 0.3 0.6 1
Vertically perforated brick � HLz 6 0.4 0.8 1
Vertically perforated brick � HLz 12 0.8 1.0 1
Perforated lime sand brick � KSL 4 0.4 0.6 1.2
Perforated lime sand brick � KSL 6 0.6 0.8 1.2
Perforated lime sand brick � KSL 12 0.8 1.4 1.2
1 Drill hole construction only with rotary drilling.2 For perforated lime sand brick the outer straps have to be at least 30 mm.
PERMITTED LOADS PER EMBEDMENT PERMITTED LOADS PER BRICK
INSTALLATION:in perforated and hollow brick
*Discard ca. 10 cm until a homogeneous grey colour appears.
1. Drill hole
3. Inject the right amount of composite mortar* (� ll the sleeve completely)
2. Clean (2x blow-out, brush)
5. Push-in the anchor rod with a rotating motion.
3. Insert mesh sleeve
6. Please observe the hardening time before installation.
1. Drill hole
3. Inject the right amount of composite mortar* (� ll the hole up to 2/3)
2. Clean (4x blow-out, brush)
4. Push-in the anchor rod with a rotating motion.
5. Please observe the hardening time before installation.
INSTALLATION:in concrete and solid brick
166
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
C h e m i c a l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
Resi FIX mortar cartridge
APPLICATION RANGEFor embedment in • Perforated brick masonry• Solid brick masonry• Concrete (VY 345 SF mortar cartridge, with approval)• Concrete (PY 345 mortar cartridge, without approval)• Natural stone (without approval)
APPROVALZ-21.3-1815Z-21.3-1816ETA-10/0134
NOTEPlease observe the corresponding approvals during planning and processing.
INCLUDED IN DELIVERYIncl. 2 MD mixing nozzles each
Anchor rod Resi AST
FEATURES• with nut and washer• Steel quality 5.8 zinc-plated or A4 stainless steel
APPROVALZ-21.3-1815Z-21.3-1816ETA-10/0134
NOTEPlease observe the corresponding approvals during planning and processing.
Con-tentmm
Composite mortar PUPrice
€ / pcs.Order description Part number
345Vinyl resin
(styrene and phthalate-free)12 VY 345 SF mortar cartridge 9571000345
345 Polyester resin 12 PY 345 mortar cartridge 9570000345
ThreadLength
mm
max. clamp thickness*
mmMaterial PU
Price € / 100
pcs.Order description Part number
Approved for polyester and vinyl ester composite mortarM8 110 20 Zinc plated steel 10 AST M8x110-V 9570098110M8 110 20 A4 stainless steel 10 AST M8x110-E 9571098110M10 130 30 Zinc plated steel 10 AST M10x130-V 9570910130M10 130 30 A4 stainless steel 10 AST M10x130-E 9571910130M12 160 35 Zinc plated steel 10 AST M12x160-V 9570912160M12 160 35 A4 stainless steel 10 AST M12x160-E 9571912160M16 190 45 Zinc plated steel 10 AST M16x190-V 9570916190M16 190 45 A4 stainless steel 10 AST M16x190-E 9571916190 *for standard inst. depth in concrete
Anchor rodDrill hole Ø
mmDrill hole depth
mmNumber of � llings
Resi Fix 345AST M8 x 110 10 80 54AST M10 x 130 12 90 33AST M12 x 160 14 110 20AST M16 x 190 18 125 11
CONSUMPTION IN SOLID BUILDING MATERIALS*
*According to the ETA approval the drill hole has to be only 2/3 � lled with the composite material.
Experience has shown more is used and a � lling of the complete drill hole has to be expected.
Anchor rodMesh sleeve
Drill hole Ømm
Drill hole depthmm
Number of � llings Resi Fix 345
AST M8 x 110 SH13-100 14 105 20
AST M10 x 130 SH15-100 16 105 15
AST M10 x 130SH15-130
16 135 12
AST M12 x 160 16 135 12AST M16 x 190 SH20-85 20 90 11
AMOUNT NEEDED IN PERFORATED BUILDING MATERIAL*
*Filling of the mesh sleeve +15%
167
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
C h e m i c a l a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
SH mesh sleeves
APPLICATION RANGE• In perforated brick masonry
FEATURES• Ensures exact calibration of threaded rod
APPROVALZ-21.3-1815Z-21.3-1816
NOTEPlease observe the corresponding approvals during planning and processing.
Applicator gun APVM
APPLICATION RANGE• For pressing-out of mortar cartridges 345 ml• For pressing-out of other various mortar cartridges
e.g. silicone
FEATURES• Suitable for VY 345 SF and PY 345 cartridges
PUPrice
€ / pcs.Order description Part number
1 APVM 345 ml 9570010345
PUPrice
€ / pcs.Order description Part number
20 MD 9570504192
Nominal drill diameter d � mm
Hole depth t � mm
suitable forThread
PUPrice
€ / 100 pcs.
Order description
Part number
14 105 M8 12 SH13-100* 957001310016 105 M10 12 SH15-100* 957001510016 135 M8 - M12 12 SH15-130 957001513020 90 M12 - M16 12 SH20-85 9570020085*Part of the approval
MD mixer
APPLICATION RANGE• For the re-use of mortar cartridges after application of a
new mixing nozzle
FEATURES• Suitable for VY 345 SF and PY 345 cartridges
APPROVALZ-21.3-1815Z-21.3-1816ETA-10/0134
NOTEPlease observe the corresponding approvals during planning and processing.
168
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
C a v i t y w a l l r e p a i r a n c h o r sA n c h o r s a n d E m b e d m e n t T e c h n o l o g y
EJOT®
Cavity wall repair anchor VSDfor double-leaf masonry
APPLICATION RANGE• For fast and adhesive-free subsequent installation of
curtain walls.• For load-bearing shells made of concrete, solid brick and
perforated brick
FEATURES• Building authorities approved anchor for subsequent
installation of curtain walls• Double expansion wall anchor: simultaneous
embedment in load-bearing wall and outer leaf• Clean and fast installation (no mortar required)• Universal expansion zone: secure installation into
concrete load-bearing shells, solid and perforated brick• The use of A4 stainless steel screws
guarantees corrosion protection• 100% installation control• Temperature-independent installation• Can be installed at 0°C
APPROVALZ-21.2-1652
TECHNICAL DATAEmbedment depth h
ef � ........................................... 70 mm
Hole depth ts � .................................................. I
d + 10 mm
Nominal drill diameter ............................................... 8 mmMinimum thickness of the outer leaf ....................... 115 mmDrive ......................................................... hexalobular T30
NOTEThe EJOT® VSD double expansion wall anchor enables the subsequent renovation of double-leaf masonry.Advanced corrosion or a complete lack of wire anchors can lead to decreased stability of the outer leaf and possibly cause considerable physical injury.
In particular curtain walls made before 1979 should be subject to further inspection.
When renovating the outer facade the stability of the curtain wall must be veri� ed. The EJOT® VSD is a very cost-effective solution for subsequent installation between load-bearing shell and outer leaf.
Ø mm
Length ld
mmDistance a
z
mmPU
Price € / 100 pcs.
Order description Part number
Anchor with A4 stainless steel screws (-E)8 205 0 - 20 100 VSD-8Ux205-E 87652056008 225 20 - 40 100 VSD-8Ux225-E 87652256008 245 40 - 60 100 VSD-8Ux245-E 87652456008 265 60 - 80 100 VSD-8Ux265-E 87652656008 285 80 - 100 100 VSD-8Ux285-E 87652856008 305 100 - 120 100 VSD-8Ux305-E 8765305600
ef
VSD
s
z
d
a
bearing masonry
external masonry
169
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
For tie pin installation
EJOT® SHOT FIRING TOOLSFor fast, safe and time-saving direct installation.A system for fastening pro� led steel sheet.
CROSS REFERENCEDirect fastening ....................................... page 109
For cutting pro� led sheets
EJOT® NIBBLERFor exact cutting even into corners and tight angles. Cuts over edges and double layer pro� led sheets.
For riveting
EJOT® RIVETING TOOLElectric riveting gun for blind rivet installation.
For � at roo� ng fasteners installation
EJOT® INSTALLATION TOOLSEJOT® installation tools for secure, fast and ef� cient fastening of EJOT Dabo® screws with and without stress plates for � xing insulation and roo� ng menbranes to � at roofs.
For drilling and fastening
POWERFUL EJOT® TOOLSSpecial screwdrivers and power drills for the installation of EJOT® products.
170
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Special nibbler KN 1.3 T
APPLICATION RANGE• For cutting pro� led sheet up to 1,3 mm thickness• Minimum tensile strength steel
up to 400 N/mm²• Minimum tensile strength aluminium
up to 250 N/mm²
ADVANTAGES:• Handy• Outstanding mobility and curve movement• High cutting speed for profiled sheets
FEATURES• Burr free cut• Easy to maintain with fast and keyless tool change• Dipping diameter of die only 19 mm• Economical due to long punch and die service life• Work direction can be set without tool in 45° steps
TECHNICAL DATAVoltage ................................................................ 220 V ~Input power: .............................................................600 WStroke rate ...................................................... 1800 1/minConnection cable length ............................................... 5 m
INCLUDED IN DELIVERY1 special nibbler1 punch1 die1 operating manual1 transport box
Order descriptionWeight
kgPrice €/
pcs.Part number
Special nibbler KN 1.3 T 1.75 9559974000
Accessories
Order descriptionPrice €/
pcs.Part number
Spare die 9559974001Spare punch 9559974002
171
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Universal nibbler KN 2.0 L
APPLICATION RANGE• For cutting profiled sheet• Minimum tensile strength steel
up to 400 N/mm² � 2,0 mmup to 600 N/mm² � 1,5 mmup to 800 N/mm² � 1,0 mm
• Minimum tensile strength aluminium up to 250 N/mm² � 3,0 mm
ADVANTAGES:• Ideal for profiled sheets up to 160 mm• For exact cuts even into corners and tight angles• Cuts over edges and doubled sheets• With short and long tool carrier
FEATURES• Burr free cut• Easy to maintain with fast and keyless tool change• 20 mm ground clearance of the die • Dipping diameter of die 24 mm• Work direction can be set without tool in 5° steps
TECHNICAL DATAVoltage ................................................................ 220 V ~Input power: .............................................................500 WStroke rate ...................................................... 1540 1/minConnection cable length ............................................... 4 m
INCLUDED IN DELIVERY1 universal nibbler1 punch1 die1 Allen key TORX® T201 operating manual1 plastic transport box
Order descriptionWeight
kgPrice €/
pcs.Part number
Universal nibbler short KN 2.0L 2.3 9559984200Universal nibbler kit KN 2.0L 2.3 9559984100Universal nibbler long KN 2.0L 2.3 9559984000
Accessories
Order descriptionPrice €/
pcs.Part number
Spare die 9559984001Spare punch 9559984002Punch guiding 9559984005Allen key TORX® T20 9559984015
172
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Riveting tools AccuBird/PowerBird
APPLICATION RANGE• For blind rivets and closed-end rivets up to Ø 5.0 mm
(all materials)• For bulbtite rivets
up to Ø 5,2 mm (AccuBird) and up to Ø 7,7 mm (PowerBird)
ADVANTAGES:• Cordless• Easy to handle• Ideal for fixing blind rivets
FEATURES• Ergonomic design• Compact, shock-resistant box• Quick exchange battery• Mandrel container• Short installation times• Immediately resets to start position after rivet operation
TECHNICAL DATABattery voltage ..................................................... 14,4 V ~Charging time ........................................................ 60 minWorking stroke ....................................................... 20 mm
INCLUDED IN DELIVERY1 riveting tool1 quick exchange battery1 rapid charger1 special nosepiece 17/29R (ensures working downwards )1 transport box
CROSS REFERENCERivets ..................................................... page 102
Order descriptionApplication
rangeup to Ø mm
Tensile force
kN
Battery capacity
Ah
Weight kg
Price €/pcs.
Part number
AccuBirdRivets: 5,0
Bulb-tite: 6,38.5 1.3 2.0 9150481100
PowerBirdRivets: 6,4
Bulb-tite: 7,7 13.0 2.6 2.2 9150481300
Accessories
Order description Application rangePrice €/
pcs.Part number
Rapid charger 14,4 V Li-Ion 9150481203Quick exchange battery 1,3 Ah 9150481202Quick exchange battery 2,6 Ah 9150481204Chuck jaws (3-part set) 9150481110Regular 17/24 nosepiece Rivets Ø 4,0 mm 9150481115Regular 17/32 nosepiece Rivets Ø 4,8 mm 9150481118Regular BT 17/32 nosepiece Bulb-tite Ø 5,2 mm 9150481106Regular BT 17/48 nosepiece Bulb-tite Ø 7,7 mm 9150481113Retainer nosepiece 17/24 R Rivets Ø 4,0 mm 9150481121Retainer nosepiece 17/29 R Rivets Ø 4,8 mm 9150481105Articulated jointed nosepiece 17/29 Rivets Ø 4,8 mm 9150481162Articulated jointed nosepiece 17/29 Rivets Ø 4,8 mm K14 9150481163
Articulated jointed nosepiece 17/32 Rivets Ø 5,2 mm 9150481164
173
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
EJOT®
Installation tool ECOsetfor screws up to 170 mm
APPLICATION RANGE• For efficient fastening of belted
EJOT Dabo® screws up to 160 mm length with EJOT® HTV 82/40 stress plates
• Modification for TKR/HTV 82/40 TK combination on request
ADVANTAGES:• Up to 5 times higher fastening performance compared
to conventional fastening solutions• Fatigue-free working in upright position with consi-
stently high installation performance• Highest grade of reliability: EJOT Climadur Dabo ®
screw is always fastened at right angles to the roof surface
FEATURES• Suitable for building sites, robust design• Screw and stress plate fed automatically• Due to the depth control screws can not be overwound• Stress plate collator capacity 100 washers• Dabo collator capacity 75 screws• Depth control for exact adjustment of the installation
depth• Protective insulation / interference-free
TECHNICAL DATAVoltage ................................................................. 220 V ~Power consumption ............................................. 600 WattPower output....................................................... 310 WattConnection cable length ............................................ 2,5 m
INCLUDED IN DELIVERY1 installation tool (incl. screwgun, socket/bit and depth control)1 tool kit1 spray oil1 operating manual
CROSS REFERENCEHTV stress plate 82/40............................. page 134
HTV stress plate 82/40 TK ........................ page 134 Dabo® screw A/F 8 RT-4,8 ........................ page 129
Dabo® screw A/F 8 R-4,8 ......................... page 128
Dabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 .............................. page 133
Order descriptionWeight
kgPrice €/
pcs.Part number
EJOT® ECOset installation tool 23.0 9151100000
Accessories
Order descriptionPrice €/
pcs.Part number
Bit H2 - 1/4“ x 30 9150006000Spray oil 100 ml 9150911000Socket A/F 8 - 1/4" x 30 9150315001Transport box 9151106000
Tool kit 9151104000
174
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
EJOT®
Installation tool ECOset Lfor screws up to 260 mm
APPLICATION RANGE• For efficient fastening of belted
EJOT Dabo® screws up to 260 mm length with EJOT® HTV 82/40 stress plate
• Modi� cation for TKR/HTV 82/40 TK combination on request
ADVANTAGES:• Up to 5 times higher fastening performance compared
to conventional fastening solutions• Fatigue-free working in upright position with consi-
stently high installation performance• Highest grade of reliability: EJOT Climadur Dabo ®
screw is always fastened at right angles to the roof surface
FEATURES• Suitable for building sites, robust design• Screw and stress plate fed automatically• Due to the depth control screws can not be overwound• Stress plate collator capacity 100 washers• Dabo collator capacity 75 screws• Depth control for exact adjustment of the installation
depth• Protective insulation / interference-free
TECHNICAL DATAVoltage ................................................................. 220 V ~Power consumption ............................................. 600 WattPower output....................................................... 310 WattConnection cable length ............................................ 2,5 m
INCLUDED IN DELIVERY1 installation tool (incl. screwgun, socket/bit and depth control)1 tool kit1 spray oil1 operating manual
CROSS REFERENCEHTV stress plate 82/40............................. page 134
HTV stress plate 82/40 TK ........................ page 134 Dabo® screw A/F 8 RT-4,8 ........................ page 129
Dabo® screw A/F 8 R-4,8 ......................... page 128
Dabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 .............................. page 133
Order descriptionWeight
kgPrice €/
pcs.Part number
EJOT® installation tool ECOset L 28.0 9151300000
Accessories
Order descriptionPrice €/
pcs.Part number
Bit H2 - 1/4“ x 30 9150006000Spray oil 100 ml 9150911000Socket A/F 8 - 1/4" x 30 9150315001Transport box 9151106000
Tool kit 9151104000
175
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
EJOT®
Installation tool ECOset HTK
APPLICATION RANGE• For secure, fast and efficient installation of EJOT® HTK
stress plates with EJOT Dabo® screws TKR and TKE
ADVANTAGES:• Short assembly times due to pre-collated fasteners• Pre-setting for different plate types• Fatigue-free fixing with high grade of installation
reliability• Insulation thickness (max. 260 mm)
FEATURES• Variable length combinations through fast and direct
raster adjustment• HTK collator change in seconds (25 pcs. pre-collated)• Due to the depth control screws can not be overwound
TECHNICAL DATAVoltage ................................................................. 220 V ~Power consumption ............................................. 600 WattPower output....................................................... 310 WattConnection cable length ............................................ 2,5 m
INCLUDED IN DELIVERY1 installation tool (includes screwgun and H2-M6x35 mm bit)1 tool kit1 operating manual
CROSS REFERENCEStress plate HTK-M .................................. page 137
Order descriptionWeight
kgPrice €/
pcs.Part number
EJOT® installation tool ECOset HTK (complete) 24.0 9151500000
Accessories
Order descriptionPrice €/
pcs.Part number
Bit H2 - M6 x 35 9250612000
Transport box 9151506000
176
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
EJOT® Manual installation tool
HSK-HTK
APPLICATION RANGE• For secure and efficient fastening of EJOT® HTK stress
plates with EJOT Dabo® screws TKR and TKE
• For secure and efficient fixing of insulating material and roo� ng membrane to pro� led steel sheet or roof boarding
ADVANTAGES:• Only one tool for all insulation thicknesses from 60 up to
400 mm• High installation reliability• Reduced installation time
FEATURES• Short and long manual installation tool
TECHNICAL DATAVoltage ................................................................. 220 V ~Input power: .................................................................6 WConnection cable length ............................................ 2,5 m
INCLUDED IN DELIVERY1 manual installation tool (screwgun included)1 tool kit1 operating manual
CROSS REFERENCEStress plate HTK 50 ................................. page 136
Dabo® screw TKR-4,8 .............................. page 130
Dabo® screw TKE-4,8 ............................ page 133
Order descriptionWeight
kgPrice €/
pcs.Part number
EJOT® manual installation tool HSK-HTK 3.2 9151516000
177
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Electric screw gun BOP 10-2
FEATURES• Mechanical switch gear for optimum torque adjustment
for various applications.• High performance motor for reliable use in almost all
applications.• Automatic spindle lock and quick-release chuck for
comfortable tool change.• Metal gear head
TECHNICAL DATAPower consumption ................................................ 500 W Power output........................................................... 270 W Laden speed ....................................... 0-460/0-1 350 rpm Idle speed ........................................... 0-700/0-2 250 rpmTorque ................................................................. 20/7 Nm Drill Ø steel ......................................................... 10/8 mm Drill Ø stainless steel ............................................ 10/8 mm Drill Ø light metal ............................................... 16/10 mm Drill Ø wood ...................................................... 35/25 mm Thread cutting ........................................................... M 10 Collar Ø ................................................................. 43 mm Drill chuck clamping range ................................ 1,5-13 mm Drill shaft thread ............................................... ½“-20 UNF Cable with plug ........................................................... 5 m Size LxW ....................................................... 289x164 mm Width across corners .............................................. 23 mmWeight acc. to EPTA ................................................. 2,0 kg
INCLUDED IN DELIVERY1 electric drill1 quick-release chuck SUPRA SKE1 extra handhold1 transport box
Order descriptionWeight
kgPrice €/
pcs.Part number
Power drill BOP 10-2 9150484000
178
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Cordless screwgunDCD 780 L2K
18,0 Volt
FEATURES• Optimal balanced 2 shift full metal gear for perfect
power-transmission• Unproblematic long-term use through safety electronics
(continuous monitoring of battery temperature, current drain and discharge protection)
• Very compact and balanced design as well as rubber covered, ergonomic handle for safety and work comfort
• 13 mm quick-release chuck and automated spindle lock • Easily adjusted switch electronic for exact tapping and
precise fastening• Integrated LED light• 2 Premium lithium system batteries with long service life
TECHNICAL DATABattery .................................................... 18,0 Volt / 3,0 Ah Power output........................................................ 350 WattIdle speed .........................................0-600 / 0-2.000 min-1
Constant torque ....................................................... 35 NmMax. drilling performance in wood / metal .......... 38 / 13 mmDrill chuck spread ..............................................1,5-13 mmWeight (incl. battery) ................................................. 1,8 kg
INCLUDED IN DELIVERY1 x 60 Min. fast battery recharger2 x 3,0 Ah Li-Ion rechargeable battery1 belt clip1 bit holder1 transport box
Order descriptionRechargeable
battery capacityAh
Weight kg
Price €/pcs.
Part number
Electric screwgun DCD 780 L2K 3.0 1.8 9150220000
179
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Cordless hammer drill DCD 985 L2K18,0 Volt
FEATURES• 3 shift full metal gear with precise torque rate for
optimum work progress• Very efficient and sturdy high-performance motor
with safety electronics• Optimal rotation speed / torque ratio for extreme heavy
duty drilling and fastening• Unproblematic long-term use through safety electronics
(continuous monitoring of battery temperature, current drain and discharge protection)
• Very compact and balanced design as well as rubber covered, ergonomic
• handle for safety and work comfort• 13 mm full metal quick-release chuck and automated
spindle lock • Easily adjusted switch electronic for exact tapping and
precise fastening• Integrated LED light• 2 Premium lithium system batteries with long service life
TECHNICAL DATABattery .................................................... 18,0 Volt / 3,0 Ah Power output........................................................ 500 WattIdle speed ..........................0-575 / 0-1.350 / 0-2.000 min-1
Idle hammer speed ...... 0-9.755 / 0-22.950 / 0-34.000 min-1
Consistent torque .................................................... 55 NmMax. drilling performance in wood / metal / stone.. 50 / 13 / 16 mmDrill chuck spread ..............................................1,5-13 mmWeight (incl. battery) ................................................. 2,4 kg
INCLUDED IN DELIVERY1 x 60 Min. fast battery recharger2 x 3,0 Ah Li-Ion rechargeable battery1 belt clip1 bit holder1 transport box
Order descriptionRechargeable
battery capacityAh
Weight kg
Price €/pcs.
Part number
Cordless screwdriver DCD 985 L2K 3.0 2.4 9150210000
180
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Special screwgun DAM5
APPLICATION RANGE• For fastening self-drilling screws
up to Ø 6,3 mm
ADVANTAGES:• Small width across corners for minimal edge distance• Light high-performance motor• Depth control for exact adjustment of the installation
depth
FEATURES• Switch for clockwise and anticlockwise rotation• Ergonomically formed handle and operating element• Hand belt for fatigue-free working with the screwgun• Protective insulation / interference-free
TECHNICAL DATATool � tting 1/4" internal hexagon,........................................................... Form F3 (DIN 3126) Voltage ................................................................. 220 V ~Input power: .............................................................450 WConnection cable length ............................................... 5 mIdle speed ................................................... 0 –1800 1/min Load speed ................................................. 0 –1250 1/min Width across corners .............................................. 23 mm
INCLUDED IN DELIVERY1 special screwgun1 depth control, including 16mm and 22 mm sleeve1 hand belt1 operating manual1 transport box
Order descriptionWeight
kgPrice €/
pcs.Part number
Special screwgun DAM5 1.6 9150508000
Accessories
Order descriptionPrice €/
pcs.Part number
K8-1/4"x50 socket 9250705101
181
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
Inst
alla
tion
to
ols
P o w e r t o o l s
Special screwgun DAM5-SH2
APPLICATION RANGE• For fastening self-drilling screws
up to Ø 6,3 mm with special long screw support
ADVANTAGES:• Small width across corners for minimal edge distance• Light high-performance motor• Depth control for exact adjustment of the installation
depth
FEATURES• Screw collar for long screw support SH2 max. 13 mm• Switch for clockwise and anticlockwise rotation• Ergonomically formed handle and operating element• Hand belt for fatigue-free working with the screwgun• Protective insulation / interference-free• Depth control for exact adjustment of the installation
depth• T-handle, height adjustable from 900 - 1120 mm• Can also be used as manual screwgun
TECHNICAL DATATool � tting 1/4" internal hexagon,........................................................... Form F3 (DIN 3126) Voltage ................................................................. 220 V ~Input power: .............................................................450 WConnection cable length ............................................... 5 mIdle speed .................................................. 0 – 1800 1/min Load speed ................................................ 0 – 1250 1/min Width across corners .............................................. 23 mm
INCLUDED IN DELIVERY1 special screwgun1 long screw support SH21 SW8-1/4"x25 socket1 operating manual1 transport box
Order descriptionWeight
kgPrice €/
pcs.Part number
Special screwgun DAM5-SH2 2.0 9150508098
Accessories
Order descriptionPrice €/
pcs.Part number
Socket SW8 - 1/4" x 25 9150315000Nosepiece 9151701029
Long screw support SH2incl. socket holder 2 and SW8 socket
9150508111
182
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
182
Inst
alla
tion
to
ols
T o o l s
Precision drill bit HSS Form S
APPLICATION RANGE• For structural steel
ADVANTAGES• Special polish to ensure high drilling capacity in case of
low drilling pressure• Short chip flute• Insensitive to breaking
FEATURES• Long service life
Ø mm
Length mm
Rotation speedrpm
Price €/ pcs. Order description Part number
Form S4.0 60 1000 S 4,0/60 drill bit 92504070004.1 55 1000 S 4,1/55 drill bit 92504050004.5 60 900 S 4,5/60 drill bit 92504340004.5 125 900 S 4,5/125 drill bit 92504350004.5 175 900 S 4,5/175 drill bit 92504360004.5 235 900 Bohrer S 4,5/235 92504502354.5 295 900 S 4,5/295 drill bit 92504502955.0 60 900 S 5,0/60 drill bit 92504090005.0 95 900 S 5,0/95 drill bit 92504100005.0 125 900 S 5,0/125 drill bit 92504110005.0 175 900 S 5,0/175 drill bit 92504120005.0 220 900 S 5,0/220 drill bit 92504130005.0 250 900 S 5,0/250 drill bit 92504140005.1 62 900 S 5,1/62 drill bit 92504390005.3 60 800 S 5,3/60 drill bit 92504150005.3 95 800 S 5,3/95 drill bit 92504160005.3 125 800 S 5,3/125 drill bit 92504170005.3 175 800 S 5,3/175 drill bit 92504180005.3 220 800 S 5,3/220 drill bit 92504190005.3 250 800 S 5,3/250 drill bit 92504370005.3 290 800 S 5,3/290 drill bit 92504380005.5 65 750 S 5,3/65 drill bit 92504200005.5 95 750 S 5,5/95 drill bit 92504210005.5 125 750 S 5,5/125 drill bit 92504220005.5 175 750 S 5,5/175 drill bit 92504080005.5 220 750 S 5,5/220 drill bit 92504230005.5 250 750 S 5,5/250 drill bit 92504920005.5 290 750 S 5,5/290 drill bit 92504240005.7 65 700 S 5,7/65 drill bit 92504250005.7 95 700 S 5,7/95 drill bit 92504260005.7 125 700 S 5,7/125 drill bit 92504270005.7 170 700 S 5,7/170 drill bit 92504280005.7 220 700 S 5,7/220 drill bit 92504290005.7 250 700 S 5,7/250 drill bit 92504320005.7 290 700 S 5,7/290 drill bit 92504330005.8 95 700 S 5,8/95 drill bit 92504410005.8 180 700 S 5,8/180 drill bit 92505801805.8 260 700 S 5,8/260 drill bit 92505802605.8 300 700 S 5,8/300 drill bit 92505803006.8 75 600 S 6,8/75 drill bit 92504300006.8 175 600 S 6,8/175 drill bit 92506801756.8 225 600 S 6,8/225 drill bit 92505100007.0 75 600 S 7,0/75 drill bit 92504400007.0 125 600 S 7,0/125 drill bit 92504990007.0 175 600 S 7,0/175 drill bit 92505000007.0 225 600 S 7,0/225 drill bit 92504930007.2 75 600 S 7,2/75 drill bit 92504420007.2 125 600 S 7,2/125 drill bit 92505040007.2 175 600 S 7,2/175 drill bit 92505050007.2 225 600 S 7,2/225 drill bit 92504940007.4 125 600 S 7,4/125 drill bit 92505060007.4 175 600 S 7,4/175 drill bit 9250507000
7.4 225 600 S 7,4/225 drill bit 9250497000
183
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
183
Inst
alla
tion
to
ols
T o o l s
Precision drill bit HSS Form D
APPLICATION RANGE• For structural steel
ADVANTAGES• Special polish to ensure high drilling capacity in case of
low drilling pressure• Short chip flute• Insensitive to breaking
FEATURES• Long service life
Precision drill bit HSCO
APPLICATION RANGE• Hard-to-work materials such as rust- and acid-resistant
steels
FEATURES• Long service life
Ø mm
Length mm
Rotation speedrpm
Price €/ pcs. Order description Part number
Form D3.0 45 1200 D 3,0/45 drill bit 92504470003.5 50 1200 D 3,5/55 drill bit 92504480004.0 55 1000 D 4,0/55 drill bit 92504010004.2 55 1000 D 4,2/55 drill bit 92504910004.5 60 900 D 4,5/60 drill bit 92504020005.0 62 900 Bohrer D 5,0/62 92504030005.3 62 850 D 5,3/62 drill bit 9250404000
Ø mm
Length mm
Rotation speedrpm
Price €/ pcs. Order description Part number
4.25 55 450 HSCO 4,25/55 92503100004.5 126 400 HSCO 4,5/126 92503800004.6 58 400 HSCO 4,6/58 92503200005.3 86 350 HSCO 5,3/86 92503000005.4 66 350 HSCO 5,4/66 92503300005.4 93 350 HSCO 5,4/93 92504440005.6 66 350 HSCO 5,6/66 92503500005.7 66 390 HSCO 5,7/66 92503600005.8 66 350 HSCO 5,8/66 92503400005.8 93 350 HSCO 5,8/93 9250540000
5.8 139 350 HSCO 5,8/139 9250370000
184
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
184
Inst
alla
tion
to
ols
T o o l s
SDS-plus hammer drill bit
APPLICATION RANGE• For masonry, concrete, natural stone, artificial stone
etc..
ADVANTAGES• For fast dust removal• Assured for service life and performance
Ø mm
Effective lengthmm
Total length mm
Price € / pcs.
Order description Part number
5 50 110 SDS plus 5/110 92000000205 100 160 SDS plus 5/160 92000000225 150 210 SDS plus 5/210 92000000256 100 160 SDS plus 6/160 92000000328 100 160 SDS plus 8/160 92000000338 150 210 SDS plus 8/210 92000000398 200 260 SDS plus 8/260 92000000378 250 310 SDS plus 8/310 92000000388 350 400 SDS plus 8/400 920000004010 100 160 SDS plus 10/160 920000003410 200 260 SDS plus 10/260 920000004710 300 360 SDS plus 10/360 920000004910 400 450 SDS plus 10/450 920000005012 100 166 SDS plus 12/160 920000006012 200 266 SDS plus 12/260 920000006112 250 310 SDS plus 12/310 920000006214 100 166 SDS plus 14/166 920000005114 150 216 SDS plus 14/216 920000005214 200 266 SDS plus 14/266 920000005314 250 316 SDS plus 14/316 920000005414 400 450 SDS plus 14/450 920000005516 100 166 SDS plus 16/166 920000005616 200 260 SDS plus 16/260 9200000057
16 300 350 SDS plus 16/350 9200000058
SDS-plus universal drill bit
APPLICATION RANGE• Materials for rotary drilling
ADVANTAGES• For fast dust removal• Assured for service life and performance
Ø mm
Effective lengthmm
Total length mm
Price € / pcs.
Order description Part number
10 100 160Universal drillSDS plus 10/160
9200000063
10 200 260Universal drillSDS plus 10/260
9200000064
185
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
185
Inst
alla
tion
to
ols
T o o l s
Ø mm
Effective lengthmm
Total length mm
Price € / pcs.
Order description Part number
5 50 1104 edgeSDS-plus 5x110
9210005110
5 100 160 4 edgeSDS-plus 5x160
9210005160
5 150 2104 edgeSDS-plus 5x210
9210005210
6 50 1104 edgeSDS-plus 6x110
9210006110
6 100 1604 edgeSDS-plus 6x160
9210006160
6 150 2104 edgeSDS-plus 6x210
9210006210
6 200 2604 edgeSDS-plus 6x260
9210006260
8 50 1104 edgeSDS-plus 8x110
9210008110
8 100 1604 edgeSDS-plus 8x160
9210008160
8 150 2104 edgeSDS-plus 8x210
9210008210
8 200 2604 edgeSDS-plus 8x260
9210008260
8 250 3104 edgeSDS-plus 8x310
9210008310
8 400 4604 edgeSDS-plus 8x460
9210008460
10 100 1604 edgeSDS-plus 10x160
9210010160
10 150 2104 edgeSDS-plus 10x210
9210010210
10 200 2604 edgeSDS-plus 10x260
9210010260
10 250 3104 edgeSDS-plus 10x310
9210010310
10 400 4604 edgeSDS-plus 10x460
9210010460
Further lengths on request.
Hammer drill bit SDS-plus with 4 edge geometry
APPLICATION RANGE• Drilling in hard, reinforced concrete
and hard natural and arti� cial stone
FEATURES• Core-reinforced drill• 4 channel drill helix• 4-edged geometry• Full metal head
ADVANTAGES• Extremely high service life with optimum drilling
performance even in reinforced concrete• For clean, dimensionally stable drill holes and constant
high drill speed. Catching of the drill in reinforced concrete is almost impossible.
• Excellent drilling progress due to optimised dust removal over 4 drill helixes
• Optimal hammer energy transfer without loss
186
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
186
Inst
alla
tion
to
ols
T o o l s
Type and size
Description Length mmPrice
€ / pcs.Order description Part number
Z2 C 25 Z2-1/4“/Cx25 9250473000H2 C 25 H2-1/4“/Cx25 9250474000H2 E 50 H2-1/4“/Ex50 9250709000H2 E 110 H2-1/4“/ x110 9200000110H2 E 127 H2-1/4“/Ex127 9200000127H2 E 152 H2-1/4“/Ex152 9200000152H2 E 170 H2-1/4“/ x170 9200000029H2 E 200 H2-1/4“/Ex200 9200000200H2 E 300 H2-1/4“/ x300 9200000300
Type and size
Description Length mmPrice
€ / pcs.Order description Part number
T20 C 25 TORX T20-1/4“/Cx25 9150010000T20W C 25 TORX T20W-1/4“/Cx25* 9150008000T25 C 25 TORX T25-1/4“/Cx25 9150009000T25W C 25 TORX T25W-1/4“/Cx25* 9150003000T30 C 25 TORX T30-1/4“/Cx25 9250431000T30W C 25 TORX T30W-1/4“/Cx25* 9250431002T25 E 70 TORX T25-1/4“/x70 9150011000T30 E 50 TORX T30-1/4“/Ex50 9250431001T30 E 200 TORX T30-1/4“/x200 9253014200T30 E 250 TORX T30-1/4“/x250 9253014250T40 C 25 TORX T40-1/4“/Cx25 9250480000T25 E 110 TORX T25-1/4“/ x110 9250140110T25 E 152 TORX T25-1/4“/ x152 9250140152T25 M6 - 33 TORX T25-M6/x33 9250251425T30 M6 - 33 TORX T30-M6/x33 9250251430
* special bit: conical design for force � t at screw head
Cross recess bit
FEATURES• External hexagon drive as per DIN 3126
TECHNICAL DATADrive ................. external hexagon head drive 1/4“ � 6,3 mm
Bit TORX®
FEATURES• External hexagon drive as per DIN 3126
TECHNICAL DATADrive ................. external hexagon head drive 1/4“ � 6,3 mm
187
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
187
Inst
alla
tion
to
ols
T o o l s
EJOT® FR-tool
APPLICATION RANGE• For reliable fixing of
corrugated and trapezoidal pro� les with FR screws – without sealing washers!
ADVANTAGES• For efficient fixing of corrugated and trapezoidal profiles• Fastener does not buckle to the side
FEATURES• Easy to handle• Optimum installation in any position• Reliable screw guidance• Captive
EJOT® FR-variotool
APPLICATION RANGE• For reliable fixing of
corrugated and trapezoidal pro� les with FR screws – without sealing washers!
ADVANTAGES• For efficient fixing of corrugated and trapezoidal profiles• Fastener does not buckle to the side
FEATURES• Easy to handle• Optimum installation in any position• Reliable screw guidance• Captive
Accessories
Order descriptionPrice €/
pcs.Part number
FR-Bit TX 25/70 9150011000Depth control sleeve for DAM 5 special screwgun -
Accessories
Order descriptionPrice €/
pcs.Part number
FR-Bit T 25/70 9151600009
Order descriptionPrice €/
pcs.Part number
EJOT® FR-tool 9151600000
Order descriptionPrice €/
pcs.Part number
EJOT® FR-variotool 9151630000
188
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
188
Inst
alla
tion
to
ols
T o o l s
Socket 1/4“
FEATURES• Drive acc. to DIN 3126 Form E
TECHNICAL DATADrive ......................... external hexagon head 1/4“ � 6,3 mm
Bit holder BT 1/4“
FEATURES• Internal hexagon acc. to DIN 3126 Form E• Drive acc. to DIN 3126 Form E
TECHNICAL DATADrive ......................... external hexagon head 1/4“ � 6,3 mm
Wrench size Length mmPrice €/
100 pcs.Order description Part number
Clamping socketA/F 8 50 K-8-1/4"x50 socket 9250705101A/F 3/8“ 50 K-3/8“-1/4"x50 socket 9250706002A/F 8 65 K-8-1/4"x65 socket 9250502100A/F 3/8“ 65 K-3/8“-1/4"x65 socket 9250489100socketA/F 8 50 S-8-1/4"x50 socket 9250705001A/F 13 50 S-13-1/4"x50 socket 9250719000A/F 10 50 S-10/8“-1/4"x50 socket 9250707000A/F 8 65 S-8-1/4"x65 socket 9250502000A/F 13 65 S-13-1/4"x65 socket 9250720000A/F 3/8“ 65 S-3/8“-1/4"x65 socket 9250489000Magnetic socketA/F 7 50 M-7-1/4"x50 socket 9250704000A/F 8 50 M-8-1/4"x50 socket 9250705000A/F 8 65 M-8-1/4"x65 socket 9250488000
A/F 7 65 M-7-1/4"x65 socket 9250487000
Internal Hexagon Length mmPrice €/
100 pcs.Order description Part number
1/4“ 42 BT-1/4“-1/4“x42 9250711000
1/4“ 57 BT-1/4“-1/4“x57 9150506031
189
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
I n s t a l l a t i o n t o o l s
189
Inst
alla
tion
to
ols
T o o l s
Socket 5/16“
FEATURES• Drive acc. to DIN 3126 Form E
TECHNICAL DATADrive ....................... external hexagon head 5/16“ � 8,0 mm
Bit holder BT 5/16“
FEATURES• Internal hexagon acc. to DIN 3126 Form E• Drive acc. to DIN 3126 Form E
TECHNICAL DATADrive ....................... external hexagon head 5/16“ � 8,0 mm
Wrench size Length mmPrice €/
100 pcs.Order description Part number
Clamping socketA/F 3/8“ 65 K-3/8“-5/16"x65 socket 9250508000A/F 8 65 K-8-5/16"x65 socket 9250503100socketA/F 8 65 S-8-5/16"x65 socket 9250503000A/F 10 65 S-10-5/16"x65 socket 9250509000Magnetic socketA/F 13 65 M-13-5/16"x65 socket 9250511000A/F 7 65 M-7-5/16"x65 socket 9250512000
A/F 8 65 M-8-5/16"x65 socket 9250513000
Internal Hexagon Length mmPrice €/
100 pcs.Order description Part number
1/4“ 45 BT-1/4“-5/16“x45 9250515001
190
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n s t a l l a t i o n t o o l s
190
Inst
alla
tion
to
ols
T o o l s
EJOT®
Blow-out pump
APPLICATION RANGE• For cleaning drill holes in concrete and solid brick
masonry
ADVANTAGES• Easy to handle• High cleaning effect• All-purpose
EJOT®
VACUtest
APPLICATION RANGE• For seal testing of screw and rivet connections on roofs
and walls
ADVANTAGES• Easy to handle• Quick and accurate seal-testing of connections• Minimal technical effort
FEATURES• For screw and rivet connections on smooth airtight
surfaces
INCLUDED IN DELIVERY1 handpump with manometer and tube2 nosepiece1 operating manual1 transport box
Order descriptionPrice €/
pcs.Part number
Blow-out pump 9150300000
Order descriptionPrice €/
pcs.Part number
VACUtest 9150580000
191
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A c c e s s o r i e s
191
Acc
esso
ries
EJOT®
Sealing washer E
ADVANTAGES:• Waterproofing• Improve the static and dynamic values• Excellent weather- and UV-resistance.
FEATURES• A2 stainless steel• 1 mm metal back• Sealing EPDM
EJOT®
Sealing washer ES
ADVANTAGES:• Waterproofing• Improve the static and dynamic values• Excellent weather- and UV-resistance.
FEATURES• A2 stainless steel• 1.8 mm metal back• Sealing EPDM• Sealing washer to cover misdrills
EJOT®
Mushroom washer
APPLICATION RANGE• For fixing light diffusing panel
FEATURES• A2 stainless steel• 1 mm metal back• Moulded EPDM part• Pre-assembled on EJOT® screws for JZ3, JA3, JZ2 and
JA2
external Ømm
internal Ømm
Elastomer thickness mm
Price €/100 pcs.
Order description Part number
11.0 5.7 2.0 sealing washer E11/2 301009230014.0 5.7 2.0 sealing washer E14/2 301000930014.0 5.7 3.0 sealing washer E14/3 301007730016.0 6.8 2.0 sealing washer E16/2 301001130016.0 6.8 3.0 sealing washer E16/3 301006730019.0 6.8 3.0 sealing washer E19/3 301006630022.0 6.8 3.0 sealing washer E22/3 301001330025.0 6.8 2.0 sealing washer E25/2 3010014300
29.0 6.8 3.0 sealing washer E29/3 3010015300
external Ømm
internal Ømm
Elastomer thickness mm
Price €/100 pcs.
Order description Part number
38.0 6.9 4.0 sealing washer ES38 301003830051.0 6.9 4.0 sealing washer ES51 3010091300
external Ømm
internal Ømm
� ange Ømm
Heightmm
Price €/100 pcs.
Order description Part number
25.0 6.3 9.0 7.0 EP 25 mushroom washer 3010070701
192
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A c c e s s o r i e s
192
Acc
esso
ries
EJOT®
Shearing load washer VS
APPLICATION RANGEFor use with EJOT® screws JZ, JA, JT
FEATURES• Zinc-plated steel• Metal thickness 4 mm
EJOT®
Thread protection sleeve
APPLICATION RANGE• Thread end covering for EJOT® screws ø 4.2 mm, Ø 4,2
mm, Ø 4,8 mm, Ø 5,5 mm, Ø 6,3 mm and Ø 6,5 mm
FEATURES• Soft plastic, RAL 9002 - grey-white or transparent
external Ømm
internal Ømm
PUPrice €/
100 pcs.Order description Part number
29.0 6.7 250 VS-29 shearing load washer 3010000003
internal Ømm
Lengthmm
PUPrice €/
100 pcs.Order description Part number
transparent3.0 10 1,000 Thread protection sleeve 3,0x10 82000107003.5 10 1,000 Thread protection sleeve 3,5x10 82000117004.0 10 1,000 Thread protection sleeve 4,0x10 82000127004.5 10 1,000 Thread protection sleeve 4,5x10 82000137004.5 25 1,000 Thread protection sleeve 4,5x25 82000437005.0 10 1,000 Thread protection sleeve 5,0x10 82000147005.5 10 1,000 Thread protection sleeve 5,5x10 8200015700RAL 9002 - grey-white3.0 10 1,000 Thread protection sleeve 3,0x10-9002 82000207003.5 10 1,000 Thread protection sleeve 3,5x10-9002 82000217004.0 10 1,000 Thread protection sleeve 4,0x10-9002 82000227004.5 10 1,000 Thread protection sleeve 4,5x10-9002 82000237004.5 25 1,000 Thread protection sleeve 4,5x25-9002 82000537004.5 35 1,000 Thread protection sleeve 4,5x35-9002 82000547005.0 10 1,000 Thread protection sleeve 5,0x10-9002 8200024700
5.5 10 1,000 Thread protection sleeve 5,5x10-9002 8200025700
Screw Thread protection sleeveJT...-2-4,2 3,0x10JF...-2H-4,8 3,0x10JT...-2H-4,8 3,0x10JT...-2-4,8 3,0x10Dabo ...-4,8 4,5x25Dabo ...-4,8 4,5x35JT...-3-4,8 3,5x10JT...-2H-5,5 3,5x10JT...-2H-Plus-5,5 4,0x10JT...-3H-5,5 4,0x10JT...-3-5,5 4,0x10JT...-4-5,5 4,5x10JT...-6-5,5 4,5x10JT...-8-5,5 4,5x10JT...-2H-6,3 3,5x10JT...-3H-6,3 4,5x10JT...-4-6,3 4,5x10JT...-6-6,3 5,0x10JT...-X-6,0 5,5x10JZ...-6,3 5,5x10
JA...-6,5 5,5x10
WHICH PUSH-ON CAP FOR WHICH EJOT® SCREW?
193
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A c c e s s o r i e s
193
Acc
esso
ries
EJOT®
Push-on capfor hexagon screw head
FEATURES• Weather-resistant polyethylene• Easy installation• For customising the screw head colour to the facade• For waterproofing the anchor screwsSuitable for
anchor type
For sealingwasher Ø mm
For screw head
External Ø
mmPU
Price €/100 pcs.
Order description
Part number*
SDF-KBSDP-KB 14
26 A/F 17 - 250Push-on cap22-17
822....700
SDF-KBSDP-KB 8
16 A/F 10 - 500Push-on cap16-10
826....700
JZ3JA3
1416
A/F 3/8 20 500Push-on cap16-3/8“
821....700
JT314 16
A/F 8 20 500Push-on cap16-8
828....700
JZ3JA3
19 22
A/F 3/8 28 500Push-on cap22-3/8“
823....700
SDF-KBSDP-KB 10
1922
A/F 13 28 500Push-on cap22-13
825....700
JZ3JA3
2529
A/F 3/8 34 250Push-on cap29-3/8“
824....700
* add four-digit RAL colour code.
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesother RAL colours and special colours on request
194
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
A c c e s s o r i e s
194
Acc
esso
ries
EJOT®
Push-on cap for hexalobular / TORX® screw head
FEATURES• Polyethylene• Easy installation• For waterproofing the anchor screws
EJOT®
AS spacer
APPLICATION RANGE• To compensate for tolerances
on wall and roof • AS-30 as installation aid for the
EJOT® � at roo� ng anchor FDD-50
FEATURES• Plastics• All-purpose for anchor diameters of 8 mm and 10 mm• Easy installation through clipping-on from the side• Variable combinations
TECHNICAL DATADimension ...................................................... 50 x 50 mm
CROSS REFERENCEFlat roo� ng anchor FDD-50 ...................... page 138
Ø Push-on capmm
PUPrice €/
100 pcs.Order description Part number*
15.0 100 Push-on cap T30 830....70018.0 100 Push-on cap T40 820....700* add four-digit RAL colour code.
Thickness mm PUPrice €/
100 pcs.Order description Part number
3 100 AS-3 86007257005 100 AS-5 86011897108 100 AS-8 860123372010 100 AS-10 860123275015 100 AS-15 8601187730
30 100 AS-30 8601188750
RAL 9006 RAL 9002 RAL 8012white aluminium grey white red brown
RAL 7016 RAL 6020 RAL 5010 anthracite-grey chrome oxide green gentian blue
Colour examplesother RAL colours and special colours on request
195
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
A c c e s s o r i e sN o t e s
Acc
esso
ries
RUINE HAUS WEITMAR, BOCHUM, GERMANY © KonvortecSupplied by EJOT: EJOT® SUPER-SAPHIR self-drilling screw JT4
196
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
C o n t a c t I n t e r n a t i o n a l
AUSTRIA EJOT Austria GmbH & Co KGGrazer Vorstadt 146A-8570 Voitsbergphone: +43 3142 2 76 00-0fax: +43 3142 2 76 00-30e-mail: [email protected] Internet: www.ejot.at
BALTIC STATESUAB EJOT BalticTitnago g. 19LT-02300 Vilniusphone: +370 5 23 11-437fax: +370 5 23 11-439e-mail: [email protected]: www.ejot.lt
BENELUXEJOT Benelux bvba/sprlReedonk 19-1B-2880 Bornemphone: +32 3 740 79 70fax: +32 3 740 79 79e-mail: [email protected]: www.ejot.be
BULGARIAEJOT Bulgaria EOOD & Co. KDLogistic center „Mimi DM“ No 31Miroviane 1289 phone: +359 2421 96 37fax: +359 2421 96 37e-mail: [email protected]
BOSNIA AND HERZEGOVINAEJOT d.o.o. SarajevoRajlovacka b.b.BiH-71000 Sarajevophone: +387 33 769 275fax: +387 33 769 276e-mail: [email protected]
CHINAEJOT Fastening Systems(Taicang) Co., Ltd.No. 88,Zhenghe Road (East) Economic DevelopmentZone, Taicang, Jiangsu Prov.Postcode: 215413, PR Chinaphone: +86 512 53 56 52 90fax: +86 512 53 56 62 92e-mail: [email protected]: www.ejot.cn
CROATIAEJOT Spojna Tehnika d.o.o.Franje Luia 23/3HR-10090 Zagrebphone: +385 1 349 86 12fax: +385 1 349 89 63e-mail: [email protected]
CZECH REPUBLICEJOT CZ, s.r.o.Zd�bradská 65CZ-25101 �iany-Jažlovicephone: +420 323 63 78 11fax: +420 323 63 78 18e-mail: [email protected]: www.ejot.cz
DENMARKEJOT Danmark ApSIndustrisvinget 8 DK-4683 Rønnede phone: +45 56 39 08 42fax: +45 56 39 91 06e-mail: [email protected]: www.ejot.dk
FRANCEEJOT France S.A.R.L.Z.l. rue du ClimontF-67220 Villéphone: +33 388 58 92 00fax: +33 388 58 92 01e-mail: [email protected]: www.ejot.fr
GERMANYEJOT Building FastenersIn der Stockwiese 3557334 Bad Laasphe, Germanyphone: +49 2752 908-0fax: +49 2752 908-707e-mail: [email protected]: www.ejot.de
HUNGARYEJOT Hungária Kft.Ócsai út 1-3H-1239 Budapestphone: +36 1 289 30 90fax: +36 1 289 30 91e-mail: [email protected]: www.ejot.hu
ITALYEJOT Tecnologie di � ssaggio S.a.s.Via PigafettaI-35011 Campodarsego (PD)e-mail: [email protected]: www.ejot.it
MEXICOEJOT ATF Fasteners de México y Compañia, S. en C.Avenida Del Siglo 180Parque Industrial MilleniumSan Luis Potosi S.L.P. 78395, Méxicophone: +52 444 870 82 00Internet: www.ejot-atf.com
NORWAYEJOT Festesystem A/SAslakveien 20AN-0701 Oslophone: +47 23 25 30 40fax: +47 23 25 30 41e-mail: [email protected]: www.ejot.no
POLANDEJOT Polska Spó�ka z ograniczon� odpowiedzialno�ci� Spó�ka komandytoUl. Je owska 9PL-42-793 Ciasnaphone: +48 34 351 06 60fax: +47 23 353 54 10e-mail: [email protected]: www.ejot.pl
ROMANIAEJOT Romania SRLStr. Depozitelor 27RO-110078 Pitestiphone: +40 248 223 886fax: +40 248 223 886e-mail: [email protected]
RUSSIAOOO EJOT Wostok107497 Moscow, Russia ul. Amurskaya 5, bld. 7phone: +7 495 941 95 84 fax: +7 495 941 95 84e-mail: [email protected]: www.ejot.ru
SERBIAEJOT Tehnika spajanja d.o.o. Autoput Beograd-Novi Sad 296X SCG-Serbia, 11080 Zemunphone: +381 11 848 60 82fax: +381 11 848 60 82e-mail: [email protected]
SLOVAKIAEJOT Slovakia, s.r.o.Juzná trieda 82 (Areál VSS)SK-04001 Košicephone: +421 55 622 17 60fax: +421 55 678 09 57e-mail: [email protected]: www.ejot.sk
SPAIN
EJOT Ibérica S. L.Pol. P 29 - C/ Azuela 78, nave 4E-28400 Collado Villalba (Madrid)phone: +34 91 286 10 20fax: +34 91 286 10 21e-mail: [email protected]: www.ejot.es
SWEDENEJOT & AVDEL System ABSantagsvägen 9S-70236 Örebrophone: +46 19 20 65 00fax: +46 19 20 65 14e-mail: [email protected]: www.ejot-avdel.se
SWITZERLANDEJOT Schweiz AGUttwiler Straße 3CH-8582 Dozwilphone: +41 71 414 52 22fax: +41 71 414 52 50e-mail: [email protected]: www.ejot.ch
TAIWANEJOT Taiwan Branch4F, 248-17 Sin Sheng Rd.,Chien Cheng Distr.806 Kaosiung, Taiwan R.O.C.phone: +886 7 811 08 18e-mail: [email protected]
TURKEYEJOT TezmakCebeci Cad. No. 84TR-34440 Küçükköy-Istanbulphone: +90 212 538 00 01fax: +90 212 538 00 93e-mail: [email protected]: www.ejot-tezmak.com
UNITED ARAB EMIRATESEJOT Middle East FZESharjah Airport International FreezoneP.O. Box 120588 SharjahUnited Arab Emirates phone: +971 6 557 97-70fax: +971 6 557 97-75 e-mail: [email protected]: www.ejot.ae
UNITED KINGDOMEJOT U.K. Ltd.Hurricane CloseSherburn Enterprise ParkSherburn- in- ElmetGB- Leeds LS25 6PBphone: +44 1977 68 70 40fax: +44 1977 68 70 41e-mail: [email protected]: www.ejot.co.uk
USAASYST TECHNOLOGIES, LLC5811 99th AvenueKenosha, Wi 53144 USAphone: +1 262 8 57 22 44e-mail: imef� [email protected]: www.asysttech.com
www.globalfasteneralliance.com
For all other countries please contact our German of� ce directly, EJOT Building Fasteners GmbH.
197
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
s
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
)
conc
rete
sc
rew
s
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tios
Inst
alla
tion
to
ols
Acc
esso
ries
Spe
cial
sc
rew
s
C o n t a c tN o t e s
© RWE Innogy Cogen GmbH BIOMASS HEATING POWER PLANT AND WOOD PELLETS PRODUCTION, GERMANYSupplied by EJOT: EJOT® SUPER-SAPHIR self-drilling screw JT3, EJOT Dabo® screws
198
Sel
f-dr
illi
ng
scre
ws
Sel
f-ta
ppin
g sc
rew
sS
peci
al
scre
ws
Flat
roo
fing
S
elf-
dril
ling
sc
rew
s D
abo®
(Aer
ated
) co
ncre
te
scre
ws
Sto
rm
was
hers
Pip
e fl
ashi
ngs
Riv
ets
Sca
ffol
ding
fa
sten
ers
Dir
ect
Fast
enin
g
Str
ess
plat
es/
flat
roo
fing
an
chor
s
Anc
hors
and
Em
bedm
ent
Tech
nolo
gy
Fast
enin
g S
yst.
for
Sol
ar
Inst
alla
tion
s
Inst
alla
tion
to
ols
Acc
esso
ries
I n d e x
AAccessories .................................. 191Accubird riveting tool ..................... 172 Aerated concrete screw FPS-E-8,0 .. 140 Anchor (see anchor bolt, scaffolding anchor)Anchor bolt S-KA ........................... 160 Anchor bolt S-KAH ......................... 161 Anchor rod Resi AST ...................... 166 Applicator gun APVM ..................... 167 Approvals ....................................... 14 AS spacer ..................................... 194BBi-met screw (see self-drilling screw JT3)Bit cross-recess ............................ 186 Bit holder BT 1/4“ .......................... 188 Bit holder BT 5/16“ ........................ 189 Bit TORX® ..................................... 186 Blind rivet AL/E-4,8 ........................ 102 Blind rivet AL/V-4,8 ........................ 102 Blind rivet K14-AL/E....................... 102 Blow-out pump .............................. 190 BOP electric screwgun 10-2 ........... 177 Bulbtite rivet .................................. 104 CCartridges 6,3/16 .......................... 111 Case-hardened self-drilling steel screw (see self-drilling screw JT2)Cavity wall repair anchor VSD .......... 168Chemical anchors .......................... 165 Chip board screw SH2-5,0 ............... 97 Chip board screw SH3-5,0 ............... 97 Chip board screw SH3-S-4,0 ............ 98 Chip board screw SH3-S-4,5 ............ 98 Chip board screw SH3-S-5,0 ............ 98 Climadur (De� nition) ........................ 26 Closed-end rivet AL/E-4,8 .............. 103 Closed-end rivet AL/V-4,8 .............. 103 Concrete screw FBS-R-6,3 ............. 139Cordless hammer drill DCD 985 L2K 179Cordless screwgun DCD 780 L2K ... 178 Corremaks® .................................... 82 CRONIMAKS®.................................. 83DDabo® (see � at roo� ng screw)DEKTITE® ..................................... 116 DH insulation support anchor .......... 163 Direct fastening ............................. 109 DMH metal insulation support anchor .......................................... 164 DMT metal insulation stress plate .... 164 Drill bits ........................................ 182 Drive rivet AL/E-4,8 ....................... 104EECOset installation tool................... 173 ECOset HTK installation tool ........... 175 ECOset L installation tool ................ 174 EJOFAST® (see side lap screw)EJOPLAST .................................... 124 EJOPLAST joint sealant .................. 124 European technical approvals ........... 15FFacade anchor SDF-KB-8 ............... 149 Facade anchor SDF-KB-10H ........... 147 Facade anchor SDF-KB-10L ........... 151
Facade anchor SDF-KB-10V ........... 145 Facade anchor SDF-S-8 ................. 148 Facade anchor SDF-S-10H ............. 146 Facade anchor SDF-S-10V ............. 144 Facade anchor SDP-KB-10S ........... 155 Facade anchor SDP-KB-14 ............. 157 Facade anchor SDP-S-10S ............. 154 Facade anchor SDP-S-14 ............... 156 Fibre cement screw (see self-drilling screw JT2-FZ-/JT4-FZ-)Flat roo� ng installation tool ............. 173 Flat roo� ng anchor FDD-50 ............ 138 Flat roo� ng screw A/F 8 R-4,8 ......... 128 Flat roo� ng screw A/F 8 RT-4,8 ....... 129 Flat roo� ng screw TKE-4,8.............. 133 Flat roo� ng screw TKR-3-4,8 .......... 131 Flat roo� ng screw TKR-4,8 ............. 130 Flat roo� ng screw VHT-R-4,8 .......... 132 FR-tool ........................................ 187 FR-variotool ................................. 187GGU ring bolt M14 ........................... 115 GU threaded sleeve ....................... 115HHammer drill ................................. 179 Hammer drill bit SDS-plus .............. 184 Hand gun ..................................... 124 Hose clamp ................................... 123 HSBR tie pin 14 ............................. 111I Information ....................................... 8 Installation aid ............................... 194 Installation tools ............................ 169 International contact ...................... 196MManual installation tool HSK-HTK .... 176 Manual pump VACUtest .................. 190 MD mixer ...................................... 167 Mushroom washer ........................ 191NNail anchor ND-K -6 ....................... 162 Nail anchor ND-K-8 ....................... 162 Nibbler ......................................... 170OORKAN storm washer corrugated ...... 87 ORKAN storm washer trapezoidal ...... 86PPipe � ashings Combo..................... 117Pipe � ashings Ezi-Seal ................... 119 Pipe � ashings Retro� t .................... 121 Pipe � ashings Soaker ..................... 120 Pipe � ashings Square..................... 118 Pipe � ashings Strip Flash................ 122 Powerbird riveting tool ................... 172 Precision drill bit HSCO................... 183 Precision drill bit HSS form D .......... 183 Precision drill bit HSS form S ........... 182 PT® screw type DG 40 .................... 100 PT® screw type DG 40-Z .................. 99 PT® screw type DG 50 .................... 100 PT® screw type DG 50-Z .................. 99 PT® screw type DG 55-C .................. 99 Push-on cap hexagon RAL .............. 193 Push-on cap TORX® ....................... 194RRenovation anchor ......................... 168
Repair screw JB3-7,2 ...................... 93 ResiFix mortar cartridge ................. 166 Ring bolt M10 ............................... 113 Rivets ........................................... 102SSandwich screw (see self-drilling screw JT2-D-/JT3-D-)Scaffolding anchor JA3-GT-6,5 ....... 113 Scaffolding anchor JA3-GU-6,5 ...... 114 Scaffolding anchor JZ3-GT-6,3 ....... 113 Scaffolding anchor JZ3-GU-6,3 ...... 114 Sealing washer E ........................... 191 Sealing washer ES ......................... 191 Self-drilling screw JT2-2-4,2 ............ 38 Self-drilling screw JT2-2-4,9 ............ 40 Self-drilling screw JT2-2-6,5 ............ 41 Self-drilling screw JT2-2H/3-4,8....... 39 Self-drilling screw JT2-2H-4,8 .......... 39 Self-drilling screw JT2-2H-5,5 .......... 40 Self-drilling screw JT2-2H-6,3 .......... 41 Self-drilling screw JT2-3-4,8 ............ 42 Self-drilling screw JT2-3-5,5 ............ 42 Self-drilling screw JT2-3H-5,5 .......... 43 Self-drilling screw JT2-3H-6,3 .......... 43 Self-drilling screw JT2-6-5,5 ............ 44 Self-drilling screw JT2-6-6,3 ............ 44 Self-drilling screw JT2-8-5,5 ............ 45 Self-drilling screw JT2-12-5,5 .......... 45 Self-drilling screw JT2-12-6,3 .......... 46 Self-drill. screw JT2-D-6H-5,5/6,3.... 47 Self-drill. screw JT2-D-12H-5,5/6,3 .. 48 Self-drilling screw JT2-FZ-6-6,3 ....... 49 Self-drilling screw JT2-FZ-12-6,3 ..... 50 Self-drilling screw JT2-FZ-F-6,5 ....... 51 Self-drilling screw JT2-ST-2-6,0 ....... 51 Self-drilling screw JT3-2-4,9 ............ 54 Self-drilling screw JT3-2-5,6 ............ 57 Self-drilling screw JT3-2-6,0 ............ 57 Self-drilling screw JT3-2-6,5 ............ 58 Self-drilling screw JT3-2H-4,8 .......... 53 Self-drilling screw JT3-2H-Plus-5,5 .. 55 Self-drilling screw JT3-3-5,5 ............ 59 Self-drilling screw JT3-6-5,5 ............ 60 Self-drilling screw JT3-6-6,3 ............ 61 Self-drilling screw JT3-12-5,5 .......... 62 Self-drill. screw JT3-D-6H-5,5/6,3.... 64 Self-drill. screw JT3-D-12H-5,5/6,3 .. 65 Self-drilling screw JT3-FR-12-5,5 ..... 63 Self-drilling screw JT3-FR-2-4,9 ....... 55 Self-drilling screw JT3-FR-2H-4,8 .... 54 Self-drill. screw JT3-FR-2H-Plus-5,5 56 Self-drilling screw JT3-FR-3-5,5 ....... 59 Self-drilling screw JT3-FR-6-5,5 ....... 61 Self-drilling screw JT3-ST-2-6,0 ....... 66 Self-drilling screw JT3-X-2-6,0 ........ 66 Self-drilling screw JT4-2-4,8 ............ 67 Self-drilling screw JT4-3H/5,5,5 ....... 69 Self-drilling screw JT4-4-4,8 ............ 69 Self-drilling screw JT4-6-5,5 ............ 71 Self-drilling screw JT4-FR-2-4,9 ....... 68 Self-drilling screw JT4-FR-2H-4,8 .... 67 Self-drilling screw JT4-FR-4-4,8 ....... 70 Self-drilling screw JT4-FR-4-5,5 ....... 71 Self-drilling screw JT4-FZ-6,5 .......... 72 Self-drilling screw JT4-S-2-4,8 ........ 73 Self-drilling screw JT4-STS-3-4,8 ..... 73
Self-drilling screw JT4-ZT-3-4,2 ....... 68 Self-drilling screw JT4-ZT-4-4,8 ....... 70 Self-tapping screw BS-R-6,3 ............ 90 Self-tapping screw Duro PT .............. 95 Self-tapping screw JA1-6,5 .............. 82 Self-tapping screw JA2-6,5 .............. 76 Self-tapping screw JA3-6,5 .............. 78 Self-tapping screw JA3-FR-4,9 ......... 91 Self-tapping screw JA3-LT-4,9 ......... 91 Self-tapping screw JA3-S-6,5 .......... 92 Self-tapping screw JA3-ZT-6,5 ......... 92 Self-tapping screw JB3-ZT-6,3 ......... 93 Self-tapping screw JZ1-6,3 .............. 82 Self-tapping screw JZ2-6,3 .............. 76 Self-tapping screw JZ3-6,3 .............. 80 Self-tapping screw JZ3-8,0 .............. 95 Self-tapping screw JZ3-S-6,3 ........... 94 Self-tapping screw JZ3-ZT-6,3 ......... 94 Self-tapping screw JZ7-6,3 .............. 83 Shearing load washer VS ................ 192 SH mesh sleeves ........................... 167 Shot � ring tool P 525 L ................... 109 Shot � ring tool P 560 ..................... 110 Side lap screw JF2-2H-4,8 ............... 38 Side lap screw JF3-2H-4,8 ............... 53 Socket 1/4“ .................................. 188 Socket 5/6“ .................................. 189 Solar Fastening System JA3-SB ...... 107 Solar Fastening System JZ3-SB ...... 107 Special nibbler KN 1.3 T ................. 170 Special screwgun DAM5 ................ 180 Special screwgun DAM5-SH2 ......... 181 Special screws ................................ 90 Stainless steel self-drilling screw (see self-drilling screw JT4)Standing seam system screw ............ 66 Steel anchor (see anchor bolt, scaffolding anchor)Storm washer .................................. 85 Stress plate Eco Tek 50 .................. 136 Stress plate HTK 50 ....................... 136 Stress plate HTK-M ........................ 137 Stress plate HTV 82/40 .................. 134 Stress plate HTV 82/40 F ................ 135 Stress plate HTV 82/40 TK .............. 134 Stress plate HTV RU ....................... 135TTest certi� cates ............................... 14 Thread protection sleeve ................ 192 Tie pin HSBR 14 ............................ 111Tools ............................................ 182U Universal drill bit SDS-plus .............. 184 Universal facade anchor SDF-KB-14U ................................. 153 Universal facade anchor SDF-S-10U ................................... 150 Universal facade anchor SDF-S-14U ................................... 152 Universal hose clamp ..................... 123Universal nibbler KN 2.0 L .............. 171VVACUtest ...................................... 190 VSD cavity wall repair anchor .......... 168
365-GB/1.5/12.11