Date post: | 31-Dec-2015 |
Category: |
Documents |
Upload: | lars-franks |
View: | 70 times |
Download: | 1 times |
Electronics Cooling MPE 635
Mechanical Power Engineering Dept.
1. To establish fundamental understanding of heat transfer in electronic equipment.
2. To select a suitable cooling processes for electronic components and systems.
3. To increase the capabilities of post-graduate students in design and analysis of cooling of electronic packages.
4. To analysis the thermal failure for electronic components and define the solution.
Course Goals
• Part-A• Main topics • Introduction to electronics cooling and thermal
packaging• Introduction to basic modes of heat transfer • Conduction heat transfer and extended surfaces in
electronic devices• Transient conduction• Natural convection heat transfer (i.e. PCB cooling) • Forced convection heat transfer (Internal and External
flow )• Fan performance• Radiation heat transfer and its applications in electronic
devices• Solving the electronics cooling problems with EES
software• Electronics cooling problems• Solution of selected electronics cooling problems
3. Basics of Heat Transfer
Modes of heat transfer
Conduction
• Conduction heat transfer as diffusion of energy due to molecular activity.
• Conduction in liquids and solids ascribed to molecules vibration (solids), translational and rotational (liquids)
Conduction
• Fourier’s law
dx
dTkqx
L
TTkqx
12
Thermal convection
• The heat transfer by convection is described by the Newton's law of cooling:
)( TThAq WA ir m o v e m e n t d u e t o t e m p e ra t u re d iffe re n c e
(a )F re e c o n v e c t io n o n e le c t ric c o m p o n e n t s c h ip s
A ir
(b )F o rc e d c o n v e c t io n o n e le c t ric c o m p o n e n t s c h ip s
F o rc e d fa n
Thermal convection
• convection heat transfer ranges Process h(w/m2.k)
Free convection - gases 2-25 - liquids 50-1000Forced convection - gases 25-250 - liquids 50-20,000Convection with two phase - boiling or condensation 2500-100,000
Thermal convection
• Example 3.1: An electric current is passed through a wire 1mm diameter and 10 cm long. This wire is submerged in liquid water at atmospheric pressure, and the current is increased until the water boils. For this situation h = 5000 W/m2.oC. And the water will be 100 oC. How much electric power must be supplied to the wire to maintain the wire surface at 114 oC?
Schematic:
Electric wire
Water
Thermal convection
• Solution:• The total convection loss from the wire is
given by.
• For this problem the surface area of the wire is A= π d L = π (1 x 10-3) (10 x 10-2) = 3.142 x10-4 m2
• The heat transfer is therefore
• And this is equal to the electric power which must be applied.
)( TThAq W
Wq 99.21)100114(10142.35000 4
Thermal radiation• The mechanism of heat transfer by radiation
depends on the transfer of energy between surfaces by electromagnetic waves in the wave length interval between 0.1 to 100 μm.
• Radiation heat transfer can travel in vacuum such as solar energy.
• Radiation heat transfer depends on the surface properties such as colors, surface orientation and fourth power of the absolute temperature (T4) of the surface.
• The basic equation for radiation heat transfer between two gray surfaces is given by
)( 42
41 TTfAq
Thermal radiation
• Example 3.2. A horizontal steel pipe having a diameter of 10 cm is maintained at a temperature of 60 oC in a large room where the air and wall temperature are at 20 oC with average heat transfer coefficient 6.5 W/m2K. The emissivity of the steel is 0.6 calculate the total heat lost from the pipe per unit length.
Thermal radiation
• Solution:• The total heat lost from the pipe due
to convection and radiation
• Because the pipe in a large enclosure then the geometrical factor ƒ = 1
)()( 44
TTfATTAh
qqq
SS
radiationconvectiontotal
mW
xxxqtotal/33.134
)293333)(1.0)(1)(6.0(1067.5)2060)(1.0(5.6 448
• There exists an analogy between the diffusion of heat and electrical charge. Just as an electrical resistance is associated with the conduc tion of electricity, a thermal resistance may be associated with the conduction of heat.
Analogy between Heat Transfer and Electric Circuits
Analogy between Heat Transfer and Electric Circuits
haR
TRqThAqkA
LR
TRqL
TkAq
convt
convtconvconv
condt
condtcondcond
1,
,
,
,
A
L
I
EERe
12
Series Circuits:
• By analogy
AhkAL
Ah
TTq
RRR
TTq
R
Tq
convtcondtconvt
t
overall
21
21
,,,
21
11
3,2,1,
21
eeee RRR
EE
R
Ei
Parallel Circuit: L1, k1, A1
L7, k7, A7
L6, k6, A6
L5, k5, A5
L4, k4, A4
L3, k3, A3
L2, k2, A2
qtotqtot
T1
T2
ittott
totttot
ttttttttot
itot
itiiii
RR
R
Tq
RRRRRRRTq
R
T
L
TAkq
,,
,
7,6,5,4,3,2,1,
,
11
1111111
q1
qtot qtot
q7
q6
q7
q5
q6
q4
q5
q3 q3
q2 q2
R7
R6
R5
R3
R2
R4q4
Combined Modes of Heat Transfer
• Combined Convection and Radiationradconvnet qqq
)( fsrrad TTAhq
)(
)(
)(
44
fs
esse
fs
radr TT
TTF
TTA
qh
)(
)()()(
)(
)(
22
44
fs
fsfsfsser
fs
fsser
TT
TTTTTTFh
TT
TTFh
• Combined Convection and Radiation
Now if we define the arithmetic mean temperature as:
If further Ts-Te<<Ts then
So we may define the radiation heat transfer coefficient as:
And finally;
Where
)()2)((
)()(2
22
fsfsfsser
fsfsser
TTTTTTFh
TTTTFh
2fs
m
TTT
fsm TTT
34 mser TFh
)( fstotnet TTAhq radconvtot hhh
Combined Modes of Heat Transfer
Combined Modes of Heat Transfer
• Combined Convection and Conduction
• This combination is likely to occur with the use of extended surfaces where the primary surface exchanges heat by convection to the adjacent fluid flow and by conduction through the extended surfaces. This case may be considered in a similar manner as the above, but here the problem doesn't need extra work as the conduction thermal resistance is predefined.
condconvnet qqq
AL
TextTskTfTshconvqnet
)(
)(
Overall Heat Transfer Coefficient
)(1
)()()(1
1
,,,,,,
",
,,,
",
,,, shhfphhshhfph
hf
msccfpc
cf
sccfpcc
cchh
AAhAA
R
kAx
AA
R
AAh
AUAU
Fluid combination U, W/m2.ºK.
Water to water 850-1700
Water to oil 110-350
Steam condenser, water in tube 1000-6000
Ammonia condenser, water in tube 800-1400
Finned tube heat exchanger, water in tubes air in cross flow
25-50