1 OF 4 IG051518-1.0 ELEMENT ™ CROWN OUTDOOR CHANNEL INSTALLATION GUIDE ® Length 48 inches SAFETY & WARNINGS QUICK SPECS / MODELS ADDITIONAL ACCESSORIES Channel Cover and Base DI-ELMT-CR-48-* DI-ELMT-CR-48-* ELEMENT ™ CROWN Outdoor LED Channel INSTALLATION GUIDE IP65 * Indicates color WET LOCATION 1. Install in accordance with national and local electrical code regulations. 2. This product is intended to be installed and serviced by a qualified, licensed electrician. 3. Do not modify or disassemble this product beyond instructions or the warranty will be void. 4. Do not submerge, or install within 5 feet of a swimming pool.
Transcript
1 OF 4 IG051518-1.0ELEMENT™ CROWN OUTDOOR CHANNEL INSTALLATION GUIDE
®
Length 48 inches
SAFETY & WARNINGS
QUICK SPECS / MODELS
ADDITIONAL ACCESSORIES
Channel Cover and BaseDI-ELMT-CR-48-*
DI-ELMT-CR-48-*
ELEMENT™ CROWN Outdoor LED ChannelINSTALLATION GUIDE
IP65
* Indicates color
WET LOCATION
1. Install in accordance with national and local electrical code regulations.
2. This product is intended to be installed and serviced by a qualified, licensed electrician.
3. Do not modify or disassemble this product beyond instructions or the warranty will be void.
4. Do not submerge, or install within 5 feet of a swimming pool.
2 OF 4 IG051518-1.0ELEMENT™ CROWN OUTDOOR CHANNEL INSTALLATION GUIDE
INSTALLATION
PLACE ELEMENT™ CROWN CHANNEL
3M ADHESIVE BACK
CUT CHANNEL TO LENGTH
Using a hack saw or band saw, cut cover to length.a
bWhen mitering the Channel and Cover, cut at an angle.MITER CUTS
STRAIGHT CUTS
ELEMENT™ CROWN Outdoor LED ChannelINSTALLATION GUIDE
Peel backing from 3M adhesive strip on back of channel.
1
2.1
2
1 2
3
1. Phillips-head Screwdriver and/or Power Drill2. Hack Saw3. Wire Snips4. Ruler5. (2x per foot) M2.9 (#4) (or similar) screws
REQUIRED TOOLS
4 5
3 OF 4 IG051518-1.0ELEMENT™ CROWN OUTDOOR CHANNEL INSTALLATION GUIDE
From one end, place Strip Light within raised channel.
ASSEMBLE STRIP LIGHT WITHIN CHANNEL
INSTALLATION (CONT.)
Allowing 3M adhesive to hold the channel in place, use screws to fasten channel to surface.*
ELEMENT™ CROWN Outdoor LED ChannelINSTALLATION GUIDE
FASTEN CHANNEL
PLACE STRIP LIGHT WITHIN RAISED CHANNEL
2.2
3.1
3
*Shown with DAZZLE® ACCENT LED Tape Light.
The lower areas on either side of the channel may be used to place and hide additional wires used for installation.
SIDE CHANNELS
*Note: Ensure that plenty of space is left between channels when installing around corners. Pinching, or bending Strip Light and/or extension cables may result in damage to the system.
3.2
*Shown with DAZZLE® ACCENT LED Tape Light.
Line up ends of channels, then overlap single cover to ensure channels are prperly aligned.
ELEMENT™ CROWN Outdoor LED ChannelINSTALLATION GUIDE
Snap covers onto channel. Insert end caps into channel ends.
PLACE COVER AND END CAP
ATTACH CONTROLLER AND DRIVERVerify a compatible driver is installed. Utilize applicable wiring when installing outdoors. (Use of wet location rated junction box recommended)
*Check Installation Guide of Tape Light used for more information.
COMPATIBLE LED TAPE LIGHTS
4.2
DAZZLE® ACCENT LIGHTING SYSTEMDAZZLE® RGB WET LOCATION STRIP LIGHTBLAZE™ WET LOCATION LED STRIP LIGHTFLUID VIEW® WET LOCATION LED STRIP LIGHTHYDROLUME® 24V LED STRIP LIGHTHYDROLUME® SLIM 24V LED STRIP LIGHTAlphaTECH™ LED STRIP LIGHT
Using Wire Snips, cut an opening in endcap large enough to slot wires.
