Date post: | 05-Apr-2018 |
Category: |
Documents |
Upload: | soner-salar |
View: | 223 times |
Download: | 0 times |
of 31
7/31/2019 ELMA Rugged Microtca Test
1/31
ELMA Trenew
Shock and
Vibration Tests
November 2007AS, FF
7/31/2019 ELMA Rugged Microtca Test
2/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 1 - AS, FF
Contents
1 Introduction .............................................................................2
2 Test equipment.........................................................................3
2.1 System ................................................................................ 3
2.2 Backplane............................................................................. 4
2.3 Shock absorber ..................................................................... 4
2.4 Load Board ........................................................................... 5
2.5 Mechanical Load Board ........................................................... 6
2.6 MCH .................................................................................... 72.7 Power Module........................................................................ 7
2.8 Module Fixing........................................................................ 7
2.9 Testing machines................................................................... 8
2.9.1 Shaker ....................................................................... 8
2.9.2 Shock test machine...................................................... 9
3 Test procedure........................................................................10
3.1 Sine Vibration (AC1 IED 61587-1)........................................10
3.2 Random Vibration (AC2 VITA 47) .........................................10
3.3 Shock (AC1 IEC 61587-1) ...................................................11
3.4 Shock (AC2 VITA 47)..........................................................11
4 Test results.............................................................................12
4.1 Sine Vibration ......................................................................12
4.2 Random Vibration.................................................................12
4.3 Shock test (AC1 IEC 61587-1) .............................................14
4.4 Shock Test (AC2 VITA 47)...................................................14
5 Conclusion ..............................................................................15
Appendix A Vibration profile (sinusoidal).................................16
Appendix B Vibration profile (random) ....................................18
Appendix C Shock profile (AC1 IEC 61587-1) ........................20
Appendix D Shock profile (AC2 VITA 47)...............................21
Appendix E MCH Log ................................................................22
7/31/2019 ELMA Rugged Microtca Test
3/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 2 - AS, FF
1 Introduction
The MicroTCA system architecture is not only dedicated for the telecom
market, but also for industrial and even for rugged applications like
transportation and MIL/AERO applications.
The following tests should show the capabilities that the ELMA MicroTCA
systems can withstand shock and vibration tests that are required. To
meet these requirements, the system and daughter cards have to be
prepared.
The system that was used is a specially adapted ATR system with aMicroTCA card cage. The AMCs have to be modified with special screwable
front panels, so that they could be fixed with captive screws to the
extrusions. Other cards, like MCH and PM are fixed with screws and
washers.
7/31/2019 ELMA Rugged Microtca Test
4/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 3 - AS, FF
2 Test equipment
2.1 System
The device under test is the ELMA Ruggedized MicroTCA system. The
system is an ARINC 404A full size ATR long. It includes a MicroTCA card
cage. The mechanic was designed according to meet the following MIL
standards:
MIL-STD 810 E for shock and vibration
MIL-STD 461 for EMI
7/31/2019 ELMA Rugged Microtca Test
5/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 4 - AS, FF
2.2 Backplane
The backplane that was included into the system is the ELMA MicroTCA
Cube backplane for rugged environments. To withstand higher shock and
vibration values, the AMCs can be fixed on the extrusions. The backplane
can contain up to six AMC cards, one MCH and one Power Module.
2.3 Shock absorber
Shock absorber can be mounted below the system to decrease the force
to the system.
7/31/2019 ELMA Rugged Microtca Test
6/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 5 - AS, FF
2.4 Load Board
The load boards that were used are ELMA full size load boards for
industrial application. The front panels are modified to be able to screw
them to the extrusions of the card cage.
The load boards are designed to be full compliant with the MicroTCA.0 1.0
specification and are capable to fulfill the complete management via IPMI.
7/31/2019 ELMA Rugged Microtca Test
7/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 6 - AS, FF
2.5 Mechanical Load Board
The mechanical load boards are based on the ELMA load boards. To fit the
ruggedized MicroTCA specification, the resistive load was removed and
mechanical loads were fixed on the base plate. The mechanical loads are
according to the MicroTCA.1 D0.5 specification with a weight of 264g (Full-
Size, Single-Width; For multiple slot test). These load boads are full
functioning intelligent load boards.
7/31/2019 ELMA Rugged Microtca Test
8/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 7 - AS, FF
2.6 MCH
The MCH that was used in the system was the NAT-MCH-GbE (one
tongue). This MCH was prepared by fixing the ribbon cable with silicon
material.
2.7 Power Module
The Power Module that was used was a CorEdge Networks PM
(CEN-MPWR-4840). It was also prepared by fixing higher devices like
aluminum electrolyte capacitors with silicon.
2.8 Module Fixing
The Modules that have no special front panel, which could be screwed to
the extrusions, are fixed with a screw and washers on the top and on the
bottom of the cards.
7/31/2019 ELMA Rugged Microtca Test
9/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 8 - AS, FF
2.9 Testing machines
All tests were made at the ICT Fraunhofer institute in Berghausen,
Germany.
2.9.1Shaker
Inv.-nr: 612
Shaker RMS SW 6005
Charge Amplifier Bruel&Kjaer 2626
Accelerometer S/N 848930
7/31/2019 ELMA Rugged Microtca Test
10/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 9 - AS, FF
2.9.2Shock test machine
Inv.-nr: 610
Shock Test Machine AVCO SM 110-3
Charge Amplifier Bruel&Kjaer 2626
Accelerometer S/N 848928
Inv.-nr: 030
Oscilloscope Hewlett/Packard 54 602A
7/31/2019 ELMA Rugged Microtca Test
11/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 10 - AS, FF
3 Test procedure
After each test period, the system was completely checked for mechanical
and electrical damage. An electrical test was performed to ensure the
functionality of the system. For this reason, the system was switched on
with all slots populated with cards. The activation of any card should show
that the system was not damaged at any position.
3.1 Sine Vibration (AC1 IED 61587-1)
2-9Hz: Magnitude 9.2mm
9-200Hz: Acceleration 3g
Frequency change: 1 Octave per minute
Axis: 3
Duration: 10 Minutes per axis
3.2 Random Vibration (AC2 VITA 47)
Frequency range: 5-2000Hz
Effective value of the acceleration 8g
Axis: 3
Duration: 60 Minutes per axis
7/31/2019 ELMA Rugged Microtca Test
12/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 11 - AS, FF
3.3 Shock (AC1 IEC 61587-1)
Shock form: Half sinus
Acceleration: 25g
Duration: 18ms
Axis: 6
Shocks per axis: 3
3.4 Shock (AC2 VITA 47)
Shock form: Half sinus
Acceleration: 20g
Duration: 11ms
Axis: 6
Shocks per axis: 3
X Y Z
+
-
7/31/2019 ELMA Rugged Microtca Test
13/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 12 - AS, FF
4 Test results
4.1 Sine Vibration
Mechanical: No issues during this test
Electrical: All slots booted up without errors.
4.2 Random Vibration
X-axis: Test was performed with shock absorbers
Mechanical: No issues during this test
Electrical: All slots booted up without errors.
Y-axis: Test was performed without shock absorbers
Mechanical: Some load resistors disassembled during tests.
Electrical: All slots booted up without errors.
Z-axis: Test was performed without shock absorbers
Mechanical: Some load resistors disassembled during tests.
Electrical: Two slots didnt boot up. After extraction and reinsertion they
booted up without errors.
7/31/2019 ELMA Rugged Microtca Test
14/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 13 - AS, FF
X-axis: Test was performed with shock absorbers
System was booted up during this test
Test duration: 30min
Mechanical: No issues during this test
Electrical: The MCH showed some error messages:
processMsg(0xc2):
Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded to hpid
pm_processEvent(50):
Power Channel Notification Event,
Sensor=0x0, Dir=0x6f, Data=0xa1 0x1b 0x01
Despite of this, the system worked fine, after the vibration test.
All cards were hot-swappable.
7/31/2019 ELMA Rugged Microtca Test
15/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 14 - AS, FF
4.3 Shock test (AC1 IEC 61587-1)
All shocks without shock absorbers
X-axis: After 6 shocks (3 shocks +X-axis, 3 shocks X-axis)
Mechanical: No issues during this test
Electrical: All slots booted up without errors
Y-axis: After 6 shocks (3 shocks +Y-axis, 3 shocks Y-axis)
Mechanical: No issues during this test
Electrical: All slots booted up without errors
Z-axis: After 6 shocks (3 shocks +Z-axis, 3 shocks Z-axis)
Mechanical: No issues during this test
Electrical: All slots booted up without errors
4.4 Shock Test (AC2 VITA 47)
All shocks without shock absorbers
X-axis: After 6 shocks (3 shocks +X-axis, 3 shocks X-axis)
Mechanical: No issues during this test
Electrical: All slots booted up without errors
Y-axis: After 6 shocks (3 shocks +Y-axis, 3 shocks Y-axis)
Mechanical: No issues during this test
Electrical: All slots booted up without errors
Z-axis: After 6 shocks (3 shocks +Z-axis, 3 shocks Z-axis)
Mechanical: No issues during this test
Electrical: All slots booted up without errors
7/31/2019 ELMA Rugged Microtca Test
16/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 15 - AS, FF
5 Conclusion
By screwing the front panels of the AMCs to the extrusions, there were no
mechanical problems. Even weight loaded boards (264g) were held
correctly in the card cage.
The electrical tests after the shock and vibration tests showed that the
boards were not damaged during the tests and were functioning well.
Further research is required to check the plating of the AMC boards and
the backplane connectors.
These tests show that MicroTCA could also be used for rugged
environments for transportation and MIL/AERO applications. Only little
modification is needed on the standard AMC boards.
7/31/2019 ELMA Rugged Microtca Test
17/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 16 - AS, FF
Appendix A Vibration profile (sinusoidal)
STATUS INFORMATION
FREQUENCY: 19.30 Hz
REFERENCE: 2.97 g pk
CONTROL ACCELERATION: 2.95 g pk
CONTROL VELOCITY: 0.24 m/s pk
CONTROL DISPLACEMENT: 3.94 mm pp
7/31/2019 ELMA Rugged Microtca Test
18/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 17 - AS, FF
CONTROL PARAMETERS
CONTROL CHANNEL(S): 1
CONTROL TYPE: SINGLE
SWEEP TIME: 6 min, 38 sec
SWEEP TYPE: LOG
STARTING SWEEP DIRECTION: UP
STARTING FREQUENCY: 2.00 Hz
LOWER FREQUENCY: 2.00 Hz
UPPER FREQUENCY: 200.00 Hz
SERVO SPEED: 1K dB/s
INPUT CHANNEL PARAMETERS
Chan(#)
Sensitivity(mV/g)
Coupling(AC/DC)
Max.Range(g pk)
1 100.00 AC 100.00
2 10.00 AC 100.00
3 10.00 AC 100.00
4 10.00 AC 100.00
5 10.00 AC 100.006 10.00 AC 100.00
7 10.00 AC 100.00
8 10.00 AC 100.00
INPUT CHANNEL DESCRIPTION
Chan # Description
1 B&K 848930
7/31/2019 ELMA Rugged Microtca Test
19/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 18 - AS, FF
Appendix B Vibration profile (random)
STATUS INFORMATION
TEST LEVEL: 0.0 dB
REFERENCE: 8.00 g rms
CONTROL: 8.81 g rms
7/31/2019 ELMA Rugged Microtca Test
20/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 19 - AS, FF
CONTROL PARAMETERS
CONTROL CHANNEL(S): 1
CONTROL TYPE: SINGLE
FREQUENCY RANGE: 2000 Hz
NUMBER OF PSD LINES: 2000
FREQUENCY RESOLUTION: 1.000 Hz
DOF: 130
SIGMA DRIVE LIMITING: 2.00
INPUT CHANNEL PARAMETERSChan(#)
Sensitivity(mV/g)
Coupling(AC/DC)
Max.Range(g rms)
1 100.00 AC 10.00
2 100.00 AC 10.00
3 100.00 AC 10.00
4 100.00 AC 10.00
5 10.00 AC 50.00
6 10.00 AC 50.00
7 10.00 AC 50.00
8 10.00 AC 50.00
INPUT CHANNEL DESCRIPTION
Chan # Description
1 B&K 848930
7/31/2019 ELMA Rugged Microtca Test
21/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 20 - AS, FF
Appendix C Shock profile (AC1 IEC 61587-1)
X-axis:
Y-axis:
Z-axis:
7/31/2019 ELMA Rugged Microtca Test
22/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 21 - AS, FF
Appendix D Shock profile (AC2 VITA 47)
X-axis:
Y-axis:
Z-axis:
7/31/2019 ELMA Rugged Microtca Test
23/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 22 - AS, FF
Appendix E MCH Log
**************************************************
**** Welcome to OK1 V2.0 for NAT-MCH ********------------------------------------------******** Core Release: V1.13 ******** BSP Release: V1.0 Beta ******** Build : Jun 25 2007 15:04:37 ******************************************************
initializing ... >H>sysMemInit: ram_addr=1400ec, ram_end=2000000M>I>mbinit()MB>T>C>S H>sysMemInit: ram_addr=18347c, ram_end=2000000M>I>mbinit()MB>T>C>S l2Main: L2 (MAC) startingL2M_init: initialize Ethernet device(s)L2M_Init: reading the onboard EthID !
*** N.A.T. FEC driver V1.4 Engineering (16:01:31 Jun 8 2007) ****** N.A.T. LXT972 driver V1.1 Engineering (16:01:32 Jun 8 2007) ***
found LXT972 Rev 2Initialize Multi-channel DMA API Alpha v0.3 (2004-04-26)L2M_Init(1): - completed successfully
l2Main: successfully finished - L2 runningtcpipMain: launching N.A.T. TCP/IP Rel. V1.12 cpipMain: (Jun 8 2007
7/31/2019 ELMA Rugged Microtca Test
25/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 24 - AS, FF
16:01:37)
L2_AttProto: attaching new protocol=5 for Process=3 and family=2,ifcall=1307fe, a6stat=0 - OK, new protoID=5, used=1
tcpipMain: process 3 attached for ProtID 5
init_tcpip: initializing TCP/IPnatattach: nat0 attached
with ethernet id 00 40 42 0b 00 14loattach: lo attached
with ethernet id 00 40 42 0b 00 14L2_AddType: adding type 0800 to port 5L2_AddType: adding type 0806 to port 5L2_AddType: adding type 1001 to port 5L2_AddType: adding type 1002 to port 5init_tcpip: finished successfullytcpipMain: sucessfully finished - TCP/IP running
------------------------------------------------------------------
NAT-MCH - Firmware Release V1.7E Beta (17:08:25 Jun 12 2007)------------------------------------------------------------------
Carrier Manager starting ....
*** N.A.T. DSPI driver V1.2 Engineering (16:01:34 Jun 8 2007) ***ETH1 link DOWNTransmit task startedTimer task startedSEL: starting timestamp taskSEL: 1970.000 00:00:00 aliveifconfig_nat0: own IP 0x8493a086 smask 0xffffff00 brdcst 0x8493a0ffifconfig_nat0: ioctl(SIOCSIFNETMASK) o.k., 0xffffff00
ifconfig_nat0: ioctl(SIOCSIFADDR) o.k., 0x8493a086ifconfig_nat0: ioctl(SIOCSIFBRDADDR) o.k., 0x8493a0ff
*** HPID started ***local host: 132.147.160.134remote host: 132.147.160.70RMCP rx port: 623RMCP tx port: 7001session: auth 0x00 id 0x00000000 seq_no 0x00000000 (size 9)
SEL initialized:max entry num: 1024sizeof entry: 16
default operations: 0x0a (cur 0x0a)cancel reservation id: 0x0001timestamp task pid: 12
SDR_REP initialized:max entry num: 4096sizeof entry: 64default operations: 0x2acurrent reservation id: 0x0001
IPMI DB: pre-initialization done - 24 entriesVPGA V1.4
*** N.A.T. BCM5396 driver V1.1 Engineering (16:01:33 Jun 8 2007) ***hpid_cm_server: starting taskmsgTaskIpmi: Message Handler started !
7/31/2019 ELMA Rugged Microtca Test
26/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 25 - AS, FF
msgTaskShelf: Message Handler started !mcmc(3): startedmcmc: Carrier FRU Info device found at 0xa4 - Header CRC okFRU size = 1127 bytesmcmc(3): active
mcmcTask: started management task for fru_id=3, i2c=0x10mcmcTask(3): State change M0->M1processMsg(3): Got Inventory Response, Inventory Size = 1127mcmcTask(3): have read 1127 bytes of fru datamcmcTask(3): mcmc has 2 sensors, reading ...ScanPM: found Power Module at I2C=0xc2pmTask(50): started management task for Power Module at i2c=0xc2 oni2cdev=13PM_S_task: found 1 power modules, waiting for negoiation complete ....ProcessMsg: No Request outstanding, ignoring Response.pmTask(50): State change M0->M1pmTask(0): Power Module Info:
Device Revision =0x80
Firmware Revision =0x00:0x00Manufacturer ID =0x38:0x60:0x00Product ID =0x00:0x00Aux Firmware Rev. =0x00:0x00:0x00:0x00
processMsg(50): Got Inventory Response, Inventory Size = 500.mcmcTask(3): found Hot Swap Sensor at=0x01processMsg(3): Got Sensor Reading Response, handle=0x01mcmcTask(3): State change M1->M2mcmcTask(3): State change M2->M3mcmcTask(3): State change M3->M4pmTask(50): have read 500 bytes of fru dataIpmiFru_PrintRecords: invalid FRU ID = 33056756pmTask(50): Power Module at 0xc2 provides 31.0 Amps payload power
pmTask(50): Power module has 4 sensors, reading .......pmTask(50): found Hot Swap Sensor num=0processMsg(50): Got Sensor Reading Response, handle=0x01pmTask(50): State change M1->M2pmTask(50): State change M2->M3pmTask(50): State change M3->M4pmTask(50): FRU active, state M4pmTask(50): PM module at ic2=0xc2 choosen as the primary PM !pmTask(50): heartbeat command completed with code = 0x80pmTask(50): detected new FRU 40, power channel=3, state=0x1b ***pmTask(50): channel 3 management power enabledpmTask(50): channel 3 #ENABLE assertedcuTask(40): started management task for Cooling Unit at i2c=0xa8 on
i2cdev=13pmTask(50): detected new FRU 5, power channel=5, state=0x01 ***cuTask(40): State change M0->M1pmTask(50): channel 5 management power enabled$ipmiSendReqMsg: PANIC - MpcI2c_Write to 0xc2 failed with code = -2$processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwardedto hpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x03 0x05PM_S: Set Flag FlagMngdPowerModules$ScanClock(60): ipmiDev=17, i2c=0x14Scanning: 0x14 - NOT FOUNDpmTask(50): channel 5 #ENABLE asserted
$ipmiSendReqMsg: PANIC - MpcI2c_Write to 0xa8 failed with code = -3mmcTask(5): started management task for i2c=0x72processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded to
7/31/2019 ELMA Rugged Microtca Test
27/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 26 - AS, FF
hpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x0b 0x05pmTask(50): detected new FRU 6, power channel=6, state=0x01 ***ScanClock(60): ipmiDev=17, i2c=0x14
Scanning: 0x14 - NOT FOUND$$$$$ScanClock(60): ipmiDev=17, i2c=0x14Scanning: 0x14 - NOT FOUND$$$$$clockTaskS: no Clock module found !ScanHub(61): ipmiDev=17, i2c=0x16Scanning: 0x16 - NOT FOUND$$$$$ScanHub(61): ipmiDev=17, i2c=0x16Scanning: 0x16 - NOT FOUND$$$$$ScanHub(61): ipmiDev=17, i2c=0x16Scanning: 0x16 - NOT FOUND$ipmiSendReqMsg: PANIC - MpcI2c_Write to 0xa8 failed with code = -3mmcTask(5): State change M0->M1$processMsg(5): Got Inventory Response, Inventory Size = 96
mmcTask(5): reading 96 bytes of fru datammcTask(5): reading FRU Info.$..$..$mmcTask(5): AMC needs 3.3 Amps powermmcTask(5): AMC has 6 sensors, reading ...hubTaskS: no HUB module found !PwrAllocate(fru 3 chan 0): allocating 0.8 A granted (available 30.2 A)$$.$$$.$$.$$$.$$.$$$.$$.mmcTask(5): found Hot Swap Sensor num=1processMsg(5): Got Sensor Reading Response, handle=0x01$mmcTask(5): State change M1->M2mmcTask(5): State change M2->M3PwrAllocate(fru 5 chan 4): allocating 3.3 A granted (available 26.9 A)
-------------------------------------------PM(1): - primary(fru 50): budget 31.0 A (alloc 4.1 A avail 26.9 A)PM(2): - unknownPM(3): - unknownPM(4): - unknown-------------------------------------------Primary Power Module:---------------------chan fruId PS1 ENA MPwr PPwr Amps-------------------------------------------1 3 y y y y 0.82 4 - - - -3 40 y y y y 0.0
4 41 - - - -5 5 y - - -6 6 y - - -7 7 y - - -8 8 y - - -9 9 y - - -10 10 y - - -11 11 - - - -12 12 - - - -13 13 - - - -14 14 - - - -15 15 - - - -16 16 - - - -
-------------------------------------------$ipmiSendReqMsg: PANIC - MpcI2c_Write to 0xa8 failed with code = -3$$$$$$$$$$processMsg(0x72): Event: NetFn=0x04, cmd=0x02, SensorType=0x01
7/31/2019 ELMA Rugged Microtca Test
28/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 27 - AS, FF
forwarded to hpid$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ipmiSendReqMsg: WARN - switchIPMB-A -> IPMB-BipmiSendReqMsg: PANIC - MpcI2c_Write to 0xa8 failed with code = -3$processMsg(0x72): Event: NetFn=0x04, cmd=0x02, SensorType=0x01 forwarded
to hpidprocessMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x1b 0x05$$$$$$$$$$$$$$$$$$$$$$$$ipmiSendReqMsg: PANIC - MpcI2c_Write to 0xa8 failedwith code = -3PM(50): Payload switched ON for FRU(5) !mmcTask(5): State change M3->M4mmcTask(5): FRU active, state M4$pmTask(50): channel 6 management power enabledpmTask(50): channel 6 #ENABLE assertedmmcTask(6): started management task for i2c=0x74
processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x0b 0x06pmTask(50): detected new FRU 7, power channel=7, state=0x01 ***pmTask(50): channel 7 management power enabledpmTask(50): channel 7 #ENABLE assertedmmcTask(7): started management task for i2c=0x76processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x0b 0x07pmTask(50): detected new FRU 8, power channel=8, state=0x01 ***
pmTask(50): channel 8 management power enabledprocessMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x0b 0x08pmTask(50): channel 8 #ENABLE assertedmmcTask(8): started management task for i2c=0x78pmTask(50): detected new FRU 9, power channel=9, state=0x01 ***pmTask(50): channel 9 management power enabledprocessMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x0b 0x09
pmTask(50): channel 9 #ENABLE assertedmmcTask(9): started management task for i2c=0x7apmTask(50): detected new FRU 10, power channel=10, state=0x01 ***pmTask(50): channel 10 management power enabledprocessMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x03 0x0apmTask(50): channel 10 #ENABLE assertedmmcTask(10): started management task for i2c=0x7cprocessMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,
Dir=0x6f, Data=0xa1 0x0b 0x0aipmiSendReqMsg: PANIC - MpcI2c_Write to 0xa8 failed with code = -3mmcTask(6): State change M0->M1
7/31/2019 ELMA Rugged Microtca Test
29/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 28 - AS, FF
processMsg(6): Got Inventory Response, Inventory Size = 96mmcTask(6): reading 96 bytes of fru datammcTask(6): reading FRU Info....mmcTask(7): State change M0->M1.processMsg(7): Got Inventory Response, Inventory Size = 96
mmcTask(6): AMC needs 3.0 Amps powermmcTask(7): reading 96 bytes of fru datammcTask(7): reading FRU Info.mmcTask(6): AMC has 6 sensors, reading ........mmcTask(7): AMC needs 3.0 Amps powermmcTask(7): AMC has 6 sensors, reading .....mmcTask(8): State change M0->M1processMsg(8): Got Inventory Response, Inventory Size = 96mmcTask(8): reading 96 bytes of fru datammcTask(8): reading FRU Info.......
mmcTask(8): AMC needs 3.3 Amps power..mmcTask(8): AMC has 6 sensors, reading ...mmcTask(9): State change M0->M1.processMsg(9): Got Inventory Response, Inventory Size = 96..mmcTask(9): reading 96 bytes of fru datammcTask(9): reading FRU Info........mmcTask(9): AMC needs 3.0 Amps powermmcTask(10): State change M0->M1mmcTask(9): AMC has 6 sensors, reading ....mmcTask(6): found Hot Swap Sensor num=1..processMsg(6): Got Sensor Reading Response, handle=0x01processMsg(10): Got Inventory Response, Inventory Size = 96
mmcTask(10): reading 96 bytes of fru datammcTask(10): reading FRU Info.mmcTask(6): State change M1->M2mmcTask(6): State change M2->M3PwrAllocate(fru 6 chan 5): allocating 3.0 A granted (available 23.9 A)ipmiSendReqMsg: PANIC - no answer from fruID=40 after 3 retries forNetFn=0x2c, cmd=0x07cuTask(40): unable to communicate with CU, waiting for extraction.$.mmcTask(7): found Hot Swap Sensor num=1...processMsg(7): Got Sensor Reading Response, handle=0x01$mmcTask(7): State change M1->M2mmcTask(7): State change M2->M3PwrAllocate(fru 7 chan 6): allocating 3.0 A granted (available 20.9 A)
.$.$$.mmcTask(10): AMC needs 3.0 Amps powermmcTask(10): AMC has 6 sensors, reading ...$$.$$..$$.$$$$.mmcTask(8): found Hot Swap Sensor num=1.processMsg(8): Got Sensor Reading Response, handle=0x01$$mmcTask(8): State change M1->M2mmcTask(8): State change M2->M3PwrAllocate(fru 8 chan 7): allocating 3.3 A granted (available 17.6 A).$$$.$$$.$$$$$$.$$$.$$$.$$$.mmcTask(9): found Hot Swap Sensor num=1$processMsg(0x76): Event: NetFn=0x04, cmd=0x02, SensorType=0x01 forwardedto hpidprocessMsg(9): Got Sensor Reading Response, handle=0x01$$mmcTask(9): State change M1->M2
mmcTask(9): State change M2->M3PwrAllocate(fru 9 chan 8): allocating 3.0 A granted (available 14.6 A)$$$.$$$$processMsg(0x78): Event: NetFn=0x04, cmd=0x02, SensorType=0x01
7/31/2019 ELMA Rugged Microtca Test
30/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
Ruggedized MicroTCA - 29 - AS, FF
forwarded to hpid$$$$$.mmcTask(10): found Hot Swap Sensor num=1$processMsg(10): Got Sensor Reading Response, handle=0x01$$PM(50): Payload switched ON for FRU(6) !mmcTask(6): State change M3->M4
mmcTask(6): FRU active, state M4$$$mmcTask(10): State change M1->M2mmcTask(10): State change M2->M3PwrAllocate(fru 10 chan 9): allocating 3.0 A granted (available 11.6 A)processMsg(0x76): Event: NetFn=0x04, cmd=0x02, SensorType=0x01 forwarded tohpid$$$$$$$$$$$$processMsg(0x7a): Event: NetFn=0x04, cmd=0x02, SensorType=0x01forwarded to hpidprocessMsg(0x7a): Event: NetFn=0x04, cmd=0x02, SensorType=0x01 forwarded tohpid$$$$$$$$$$$$$$$$$$$$processMsg(0x7c): Event: NetFn=0x04, cmd=0x02,SensorType=0x01 forwarded to hpid$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$PM(50): Payload
switched ON for FRU(7) !mmcTask(7): State change M3->M4mmcTask(7): FRU active, state M4$$$$processMsg(0x78): Event: NetFn=0x04, cmd=0x02, SensorType=0x01forwarded to hpid$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$PM(50): Payload switched ON for FRU(8) !mmcTask(8): State change M3->M4mmcTask(8): FRU active, state M4$$$processMsg(0x7a): Event: NetFn=0x04, cmd=0x02, SensorType=0x01 forwardedto hpid$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$PM(50): Payload switchedON for FRU(9) !
mmcTask(9): State change M3->M4mmcTask(9): FRU active, state M4$$processMsg(0x7c): Event: NetFn=0x04, cmd=0x02, SensorType=0x01 forwardedto hpid$$$$$$$$$$$$$$$$$$$$$$$$$PM(50): Payload switched ON for FRU(10) !mmcTask(10): State change M3->M4mmcTask(10): FRU active, state M4$pmTask(50): heartbeat command completed with code = 0x80
-------------------------------------------PM(1): - primary(fru 50): budget 31.0 A (alloc 19.4 A avail 11.6 A)PM(2): - unknownPM(3): - unknown
PM(4): - unknown-------------------------------------------Primary Power Module:---------------------chan fruId PS1 ENA MPwr PPwr Amps-------------------------------------------1 3 y y y y 0.82 4 - - - -3 40 y y y y 0.04 41 - - - -5 5 y y y y 3.36 6 y y y y 3.07 7 y y y y 3.0
8 8 y y y y 3.39 9 y y y y 3.010 10 y y y y 3.0
7/31/2019 ELMA Rugged Microtca Test
31/31
Ruggedized MicroTCAShock and vibration tests by ELMA Trenew Electronic
11 11 - - - -12 12 - - - -13 13 - - - -14 14 - - - -15 15 - - - -
16 16 - - - --------------------------------------------processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x1b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x5b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,
Dir=0x6f, Data=0xa1 0x1b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x5b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x1b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x5b 0x01
processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x1b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x5b 0x01processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpidpm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x1b 0x01
SEL: 1970.000 00:16:40 alive
processMsg(0xc2): Event: NetFn=0x04, cmd=0x02, SensorType=0xf3 forwarded tohpid
pm_processEvent(50): Power Channel Notification Event, Sensor=0x0,Dir=0x6f, Data=0xa1 0x1b 0x01
SEL: 1970.000 00:33:20 alive