Tough where it’s rough, precise in performanceHOG 86 – the incremental HeavyDuty encoder for highest demands

Your benefi ts at a glance: Extremely robust Quickly installed Reliable and precise

HOG 86 – the HeavyDuty encoder with reserve capacity.Harsh ambient conditions like in steel plants, at gantry cranes or vertical lift bridges demand the most of the deployed encoders.For reliable long-term operation they must provide the necessary high reserve potential. The new encoder platform HOG 86 byBaumer Hübner, previously Hübner Berlin, will meet even the

highest demands. With 50 years of expertise gained at the forefront of Heavy Duty technology, Baumer presents unrivalled resilient products with outstanding fl exibility and design benefi ts which excel with versatile installation capabilities.

Extremely robust.Failsafe in any environmentThe solid, extremely sturdy housing with minimum 10 mm wall thickness is a prerequisite design benefi t in reliable encoder opera-tion. Special anti-corrosion coating ensures seawater resistance in compliance with C4 protection. Additional encapsulation will keep the electronics safe against dirt, soiling and humidity even while the connection cover is opened for installation.

Protected against bearing damageInductive shaft currents up to 2.5 kV are safely compensated by insulated bearings or hybrid bearings to prevent the encoder from damage. Optional longlife hybrid bearings ensure up to 100 000 hours service life.

Safe at extreme temperaturesThe encoder reliably endures temperatures from -40 to +100 °C in long-term operation.

Capable of high shaft loadsThe proven, large high-end ball bearings are optimally spaced. They allow for high radial and axial shaft loads and thus provide substantial reserve capacities for ultimate longevity.

Defying any environmentSpecialised housing encapsulation and shaft seals enable long-term IP 66 protection and will reliably prevent the encoder from damage caused by penetration of dust, dirt or liquids.

Dual bearings Insulated bearings

Interference-immune sensing by OptoASIC

EX protectionHigh-quality seals IP 66

High tempe-ratures

Cold climate

Robust design

Easy to install.Ultimate mounting fl exibilityThe torque support can be directly attached using the four moun-ting threads at front and rear or alternatively at 12 different angles by aid of a support plate.

Safe and precise.Quick installation, less downtimeThe optional Enhanced Monitoring System (EMS) monitors vital encoder functionalities throughout the entire speed range, eases error tracing and thus will signifi cantly reduce expensive downtime. The multicolor LED provided at the encoder signals proper encoder supply and output driver operation as well as signal integrity. The encoder activity status is reported by the error output. The EMS monitoring functionality will signal connection errors right away during installation for eased and quick commissioning.

Perfect signal qualityHigh-performance, resilient output drivers ensure top signal quality over 500 m (TTL) respectively 300 m (HTL) cable routing. With fi ber-optic interface the encoder will even master reliable signal transmission within a distance of 2 km in environments with high ambient interference. The confi guration with fi ber-optic interface is also available with redundant sensing.

Proven sensing techniqueThe resilient sensing method by OptoASIC is immune against inter-ference and will ensure constantly high signal quality and precise measuring results even at frequent temperature changes and in harsh environments.

Always the best connectionWhether cable outlet, robust M23 connector or HeavyDuty terminal box which is rotatable through 180° - especially in harsh environ-ments HOG 86 provides outstanding fl exibility thanks to varied connection capabilities. The terminal box is optionally available with fi ber-optic interface.

HOG 86 M – redundant signals for ultimate safety and availability.Two-channel detection of relative position or rotation speed using two independent signal outputs is the most reliable method to identify errors at machines or production facilities. HOG 86 M hosts two sensing systems which are fully independent from each other. Where required, the optional monitoring functionality EMS will control both systems and this way provide prerequisite conditions for safety-relevant solutions.

Terminal box for quick and easy installation: Eased connection by pre-assembled cable.On-site modifi cations not required Cable outlet rotatable through 180° Optimum cable routing in any installation position Reliable and safe connection. Simply fi t the terminal box and secure by two screws

Terminal boxrotatable through 180°

and secure by two screws

rotatable through 180°

www.baumer.com

More product information on our HeavyDuty encoders is available for download under www.baumer.com/HOG86 or will be gladly provided by our encoder experts.Contact us.

HOG 86 T

HOG 86 T HOG 86 F HOG 86 K HOG 86 M HOG 86 L HOG 86 ML

Connection Terminal box rotatable through 180°

M23 connector outlet

Cable outlet 2 x terminal box (redundant sensing and signal output)

Terminal box with fi ber-optic interface

2 x terminal box with fi ber-optic in-terface (redundant sensing and signal output)

Insulated bearings/option: hybrid bearings

Shaft Non-through hollow shaft, diameter 12 mm or 16 mmCone shaft 1:10, diameter 17 mm

Shaft material in all confi gurations: stainless steel

Resolution 500 to 2500 steps/turn

Interface HTL / push pull TTL / RS422

Fiber-optic and HTL / push pullTTL / RS422

Output signals K1, K2, K0 + invertedError output (only with EMS)

EMS Optional

Operating voltage 5 VDC ±5 % 9…30 VDC

Ex protection II3G Ex nA T4 X (gas), II3D Ex tD IP66 A22 T135° C (dust)

HOG 86 F

HOG 86 product overview.

Subj

ect t

o m

odifi

catio

n in

tech

nic

and

desig

n. 1

2/11

No.

110

8816

7

HOG 86 ML

Baumer GroupInternational Sales P.O. Box · Hummelstrasse 17 · CH-8501 FrauenfeldPhone +41 (0)52 728 1122 · Fax +41 (0)52 728 1144sales@baumer.com · www.baumer.com

Find your local partner:www.baumer.com/worldwide