32
9000 524 312 (8912) en Instructions for use
���� �� ��� �����
en Instructions for use
en IndexSafety instructions 4 . . . . . . . . . . . . . Getting to know your appliance 6 . . Water softener 7 . . . . . . . . . . . . . . . . Filling the salt dispenser 8 . . . . . . . . Adding rinse aid 9 . . . . . . . . . . . . . . . Utensils 10 . . . . . . . . . . . . . . . . . . . . . . Detergent 13 . . . . . . . . . . . . . . . . . . . . auto 3in1 14 . . . . . . . . . . . . . . . . . . . . . Overview of programmes 16 . . . . . . . Washing dishes 17 . . . . . . . . . . . . . . . Additional functions * 19 . . . . . . . . . . . Maintenance and care 19 . . . . . . . . . . Fault finding 22 . . . . . . . . . . . . . . . . . . Customer Service 25 . . . . . . . . . . . . . Information 25 . . . . . . . . . . . . . . . . . . . Installation 26 . . . . . . . . . . . . . . . . . . . . Waste disposal 27 . . . . . . . . . . . . . . . .
en
4
Safety instructions
DeliveryImmediately check the packaging anddishwasher for any damage which mayhave been caused in transit. Do not usea damaged appliance, but consult yoursupplier.Please dispose of packaging materialproperly.
InstallationInstall and connect the applianceaccording to the installation andassembly instructions.The dishwasher must NOT beconnected to the power supply duringinstallation.Ensure that the protective conductorsystem of the domestic electricitysupply has been installed correctly.Electrical connection conditions mustcorrespond with the specifications onthe rating plate of the dishwasher.If the dishwasher is to be installedin a high-sided unit, ensure that the unitis attached properly and also at therear.Built-under and built-in appliancesshould always be installed under acontinuous work surface which isattached to the adjacent cupboards, inorder to ensure that the appliance isentirely stable.After the appliance has been installed,the mains plug should still be easilyaccessible.Not on all models:The plastic housing on the water inputcontains an electrically operated valve.The connecting wires are inside theinlet hose. Do not cut through this hoseand do not immerse the plastic housingin water.
WarningFor safety reasons, if the appliance is notfitted in a recess, thereby making a sidewall accessible, the door hinge areashould be covered at the side.(Risk of injury)Covers are available as optionalaccessories from customer services orspecialist stores.
In daily use
WarningKnives and other sharp-pointed utensilsmust be placed with the points downin the cutlery basket or horizontally inthe utensils basket.
Use the dishwasher only in thehousehold and only for its designedpurpose, i.e. for washing domesticdishes.Do not lean or sit on the open door.The appliance could tip.Please note that free-standingappliances may tip over if the basketsare overloaded.The water in the appliance is notdrinking water.Do not add any solvents to the washingchamber. Danger of explosion!Open the door carefully whenthe programme is still running. Thereis a risk of hot water spraying out ofthe appliance.To prevent injuries, e.g. causedby stumbling, open the dishwasheronly briefly in order to load and unloadthe dishwasher.Read and observe the safetynformation and instructions for use onthe packaging for cleaning and rinsingagents.
en
5
Children in the householdIf fitted, use the childproof lock. Anexact description can be found in theback of the envelope.Do not allow children to play withor operate the appliance.Keep children away from detergentsand rinse aid. These may causechemical burns in the mouth, throat andeyes or asphyxiation.Keep children away from an opendishwasher. There could still bedetergent residue inside.If the appliance is installed at eye-level,ensure when opening and closing thedoor that children are not caughtor crushed between the appliance doorand the cupboard door situated below.
Childproof lock (button lock)You can secure your appliance from beingunintentionally switched over (e.g.improper operation by children).Activating the button lock:
Select the required programme.Hold down the button B forapprox. 4 sec. until this is indicatedon the digital display.
If any button is pressed while theprogramme is running, this is indicatedon the digital display. It is not possible toend (reset) the programme.Deactivating the button lock:
Hold down the button B forapprox. 4 sec. until the display goesout.
At the end of the programme ( on thedigital display) the button lock is cancelled.If there is a power failure, the button lockis retained. Whenever a programmeis restarted, the button lock mustbe reactivated.
DamageThe appliance may be repaired andopened up by a technician only. Firstdisconnect the appliance from thepower supply. Pull out the mains plug(do not tug the power cord!) or switchoff the fuse. Turn off the tap.
DisposalMake redundant appliances unusableto prevent subsequent accidents.Dispose of the appliance in anenvironmentally friendly manner.
Warning
Children could get locked in the appliance(risk of suffocation) or get stuck in otherpositions.Therefore: Remove the mains plug, cut themains wire and set aside. Damage thedoor lock so that the door can no longerbe closed.
Before using for the first timeThe appliance was checked before it leftthe works. In order to remove possiblewater test remains, use the appliance forthe first time without any dishes, usingthe highest temperature. Also fill salt, rinseaid and detergent in the fillingcompartments.
en
6
Getting to know yourappliance
Diagrams of the control panel and theinterior of the appliance can be foundin the envelope at the front.Individual positions are referred to inthe text.
Control panel1 Main switch2 Digital display/
Programme progress indicator3 Time delay *4 Additional options *5 Door opener6 Salt refill indicator7 Rinse-aid refill indicator8 “Check water supply” indicator *9 Programme buttons
* not included with all models
Appliance interior20 Top basket
21 Additional cutlery basket for the topbasket *
22 Top spray arm
23 Additional cup rack *
24 Bottom spray arm
25 Float **
26 Bottom basket
27 Salt dispenser
28 Filters
29 Cutlery basket
30 Dispenser for rinse aid
31 Detergent dispenser
32 Catch
33 Rating plate
* some models** The float ensures that the applianceinterior is not overfilled. Only customerservice may maintain, remove and installthe float.
You will need to purchase thefollowing before using thedishwasher for the first time:– special salt for use in dishwashers– detergent– rinse-aidOnly use products, which are suitable fordishwashers.
en
7
Water softener
In order to rinse dishes and glassessatisfactorily, the dishwasher requires softwater, i.e. containing little or no lime,otherwise water stains will be left behindon crockery and glasses, etc.If the tap water exceeds a certain level ofhardness, it must be softened, i.e.decalcified, so that it can be used in thedishwasher.This is achieved by adding a special saltto the water softener inside thedishwasher. The water softener, that is the requiredamount of salt, is set up according to howhard the tap water is.
Setting up the water softenerDetermine the level of hardness of yourtap water. Your local water company orservice agent can help you with this.Identify setting from the following waterhardness table.
Water hardness table
Press and hold the B programmebutton, and set the main switch 1 toON, before releasing the programmebutton again.The indicator lamp for the B buttonflashes, as does the figure in the numerical display. The latterrepresents the value that was pre-set inthe factory.
To change the setting:Press the B programme button 9 .
Every time the button is pressed, thefigure increases by one. After reaching
, the display starts at again.Set the main switch 1 to OFF. Thenew setting is stored in the appliance’smemory.
Approx. 4 litres of water are required forregenerating the water softening system.The overall water consumption per loadcan therefore be increased by between 0and a maximum of 4 litres according to thewater hardness setting.
en
8
Filling the salt dispenser
Salt must always be filled before theappliance is switched on, so that excesssalt solution is immediately flushed awayto prevent corrosion.
Open the screw-type cap of thecompartment 27 .Before using the appliance for the firsttime, pour about 1 litre of water in thesalt container.Then refill with salt (not cooking salt)until the salt container is full(max. 1.5 kg). When you refill the salt,water is being displaced and drains off.
* on applicable models
The LOW SALT indicator 6 on the front panel will light up initially but will extinguishagain after a short period when the saltsolution has become sufficientlyconcentrated.When the control is set to , it is notnecessary to fill up with salt as none willbe consumed while the dishwasher isoperating. The LOW SALT indicator isswitched off. If the control is set between
and , then salt must be added to thedispenser.
WarningDo not pour detergent into the containerfor special salt. This would destroy thewater softener.
Salt refill indicatorAs soon as the salt refill indicator 6 is liton the control panel, refill with saltimmediately before the next rinse cycle.Depending on the washing frequency andthe hardness setting, the regeneration saltmay not have to be topped up for severalmonths.
en
9
Adding rinse aid
The rinse aid is required for stain-freeutensils and clear glasses.Use only rinse aid for domesticdishwashers.
Open the cover on the rinse-aiddispenser 30 . To do this, press the
mark (1 ) on the cover andsimultaneously lift the cover on the
control plate (2 ).
Carefully pour in the rinse aid to justbelow the edge of the filler opening.
Close the lid, ensuring that you hear itsnap closed.
To prevent excessive foam formationduring the next rinse cycle, remove anyrinse aid which has run over with a cloth.
Adjusting the amount ofrinse-aidThe amount of rinse-aid added to thewater can be varied by adjusting thestepless control. The rinse-aid control hasbeen set to ”4” in the factory.
Do not alter the setting of the rinse-aidcontrol unless streaks (turn knob towards”–”) or water marks (turn knob towards ”+”)are left on the dishes.
30
Rinse aid controller
Rinse-aid refill indicatorAs soon as the rinse-aid refill indicatorlights up on the control panel 7 ,refill with rinse aid.If using detergent products with integratedrinse aid, the rinse-aid refill indicatorcan be switched off (see “Switchingthe rinse-aid refill indicator off and on”in the “auto 3in1” chapter).
en
10
Utensils
Not suitableCutlery and utensils made of wood.Fragile decorative glasses,hand-crafted and antique utensils.These decorative items are notdishwasher-proof.Plastic parts sensitive to hot water.Copper and tin utensils.Utensils which are soiled with ash,wax, lubricating grease or ink.Absorbent materials such as spongesand cloths.
Aluminium and silver parts have atendency to discolour and fade during thewash cycle. Even some types of glass(e.g. crystal glass objects) may turn cloudyafter many wash cycles.
Recommendation:In future buy utensils which are identifiedas dishwasher-proof.
Damage to glassware and otherdishesPossible causes:
type of glass or manufacturing processchemical composition of detergentwater temperature and duration ofdishwasher programme.
Suggested remedy:
Use glassware or porcelain dishes thathave been marked ’dishwasher–proof’by the manufacturer.Use a mild detergent that is describedas ’kind to dishes’. If necessary, seekfurther information from detergentmanufacturers.Select a programme with as low atemperature and as short a duration aspossible.To prevent damage, take glass andcutlery out of the dishwasher as soonas possible after the programme hasended.
Loading the dishwasherIt is not necessary to rinse them offunder running water.When loading the dishwasher, ensurethat� all utensils are secure and cannot
fall over.� the openings of all receptacles are
face down.� curved or indented utensils are at
an incline, allowing water to drain.� the two spray arms can rotate freely.
Very small items should not be washed inthe dishwasher as they could easily fall outof the baskets.
Removing the dishesTo prevent water dripping from the topbasket onto the dishes in the lower basket,we recommend that you empty the lowerbasket first and then the top basket.
Cups and glassesUpper basket 20
* on applicable models
en
11
Pots and pansLower basket 26
CutleryCutlery should be placed in thedishwasher always unsorted and with theeating surface pointing downwards. Thespray jet is then better able to reach theindividual parts.To prevent injuries, place long, pointedaccessories and knives on the étagère(some models) or on the knife shelf(available as an accessory).
Folding spikes ** on applicable modelsTo improve stacking of pots and pans, thespikes can be folded down.
Shelf ** not on all modelsLean tall glasses and those with longstems against the shelf – not against otheritems to be washed.
Long items, serving cutlery, salad serversor knives should be placed on the shelf sothat they do not obstruct the rotation of thespray arms. The shelf can be folded backwhen not required for use.
Small accessories holder** some modelsLight-weight plastic accessories, e.g. cups,lids, etc. can be held securely in the smallaccessories holder.
en
12
Adjusting the heightof the basket ** some modelsIf required, the height of the upper utensilsbasket can be adjusted to provide morespace for tall utensils either in the upperor lower basket.
Appliance height in cm 81 86
Max. ø in cm upper 20/25* 20/25*
max. ø in cm lower 30/25* 34/29*
Select one of the two following proceduresaccording to the design of the top basketfor your appliance model:
Top basket with upper andlower roller pairs
Pull out the top basket.Remove the top basket and re-attachit to the upper or lower rollers.
Top basket with side levers(Rackmatic)
Pull out the top basket.To lower the basket, press in one leverand then the other situated on the leftand right of the basket exterior, holdingthe basket firmly on the sides of theupper edge to prevent it from fallingdown.
To raise the basket, hold the basket onthe sides of the upper edge and lift itup.Before re-inserting the basket again,ensure that it is at the same heighton both sides. Otherwise, the appliancedoor cannot be closed and the upperspray arm will not be connected tothe water circuit.
en
13
Detergent
You can use commercially available liquidor powder proprietary detergents fordishwashers or TABS (do not usehandwash!).If phosphate-free detergents are used withhard tap water, white deposits may bedeposited more easily on utensils andthe container walls. This can be remediedby adding more detergent.See detergent packaging to determinewhether a detergent is suitable for silverparts.If you have any other questions, werecommend that you contact the helplinesof the detergent manufacturers.
Detergent dispenser withdosing aidThe graduated detergent dispenser helpsyou pour in the correct amount.Lower line: 15 mlMiddle line: 25 mlFull to the brim: 40 ml
If the detergent dispenser 31 is stillclosed, press the lock 32 to open thedetergent dispenser.
Adding detergentFill the dispenser 31 with detergent.Dosage: see manufacturer’sinstructions on the detergentpackaging.
NoteThe cleaning tabs from variousmanufacturers exhibit differing dissolvingproperties, so washing power may notdevelop fully during short programmes andthere may be undissolved cleaning agentresidue. It is recommended to usewashing powder for these programmes.The Intensive programme (on somemodels) requires one tab only. When usingwashing powder, you can apply someof this cleaning agent to the inside ofthe appliance’s door.
Reduce costs!If your dishes are only moderately dirty,you may be able to use less detergentthan recommended.
Close the lid on the detergentcompartment.Press down the lid (1) until it clicksshut (2).
If you are using detergent in tablet form,read the manufacturer’srecommendations on the packaging inorder to determine where the tablets should beplaced inside the dishwasher (e.g. incutlery basket, detergent compartment,etc.).Make sure that the lid on the detergentcompartment is closed, even if you areusing tablets.
en
14
auto 3in1
The use of so-called combined detergentproducts may make the use of rinse aidand/or salt unnecessary.There are currently several types ofcombined detergent products available.
2in1: They contain detergent and rinseaid or salt function.3in1: They contain detergent, rinse aidand salt function.4in1: They contain a detergent,rinse-aid, salt function and an additionalglass protection component.
In addition, other combined products witha comparable effect are offered accordingto the manufacturer.>>> Always check the type of detergent
or combined product which youare using!
Always follow the operating instructionsor the information on the packaging.
The rinse programme is automaticallyadjusted in order to obtain the bestpossible rinsing and drying result.Observe the following importantinformation if using combined cleaningproducts:
Regeneration salt is not required up toa water hardness of 21� dH (37� fH,26� Clarke, 3.7 mmol/l) only. No othersettings on the appliance are required.Salt is still required if the waterhardness is above 21� dH (37� fH,26�Clarke, 3.7 mmol/l). Fill the saltdispenser with salt 27 and selectsetting 6 on the water softening system.
If in doubt, please contact the detergentmanufacturer, especially if:
the utensils are very wet at the endof the programme.limescale forms.
NoteOptimum rinsing and drying results can beobtained by using standard detergents inconjunction with separate application ofsalt and rinse aid.
Observance of the operating instructionsor information on the packaging of thecombined detergents determines theireffectiveness.
Note
Even if the rinse aid and/or salt refillindicator is lit, the rinse programme runscorrectly when 3in1 products are used.
If the rinse aid refill indicator 7 or saltrefill 6 indicator is defective and youwould like to switch it off, proceed asfollows:
Switching the rinse aid refillindicator off and onYou can switch the rinse aid refill indicator
7 on or off. This function can bechanged as follows.
Close the door.Hold down the programme button Cand press the main switch 1 until thedigital display lights up, then release thebuttons.
2 is indicated on the digital display (rinse aid refill indicator on).
By pressing the programme buttonC , you can switch off or switch
on the rinse aid indicator.
Switch off the main switch 1 ;the setting is saved.
en
15
Switching the salt refillindicator / water softeningsystem off and on
Close the door.Hold down the programme button Band switch on the main switch 1 ,then release the buttons.The illuminated button B and thefactory-set value on the digitaldisplay flash.
To change the setting: press theprogramme button B .
Each time the button is pressed, the setvalue increases by one; when the value
is reached, the display jumps backto (the salt refill indicator / watersoftening system has been switchedoff).Switch off the main switch 1 .The set value is stored within thedevice.
Approx. 4 litres of water are required toregenerate the water softening system.As a result, the water consumption perrinse cycle increases by 0 to maximum4 litres depending on the water hardnesssetting.
NoteIf you use the detergent and rinse aidseparately or switch from combineddetergents to standard cleaning products,ensure that the rinse aid refill indicator hasbeen switched on and the water softeningsystem has been set to the correct waterhardness.
en
16
Overview of programmesThe max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia.
Coffee, cake, milk,sausage, cold drinks,
salads
Soups, soufflés,potatoes, pastries,
rice, eggs,fried food
Delicate
Type of Dishese.g. porcelain,
pans,cutlery,glasses, etc.
Type of foodremnants e.g.
Programme-sequence
Dry
Clean55�
Clean40�
Prerinse
Clean55�
Clean45�
Soups,potatoes,pastries,
rice, eggs,fried food
Washprogramme
Very littleLittleLargeAmount offood remnants
State of foodremnant
Intensive70�
Eco50�
Gentle40�
Quick45�
Prerinse
MixedMixedNon-sensitive
Medium Lightly AdhesiveVeryadhesive
Dry
Clean65�
Clean50�
Prerinse
Dry
Clean70�
Dry
Clean70�
Prerinse40�
The
pro
gram
me
sequ
ence
isop
timis
ed a
nd a
djus
ted
acco
rdin
gto
the
degr
ee o
f soi
ling
on th
eut
ensi
ls.
Auto55�-65�
Prerinse
Rinse off ifthe disheshave been
stackedfor several
days inthe
dishwasher prior towashing.
Inter-mediate
rinse
Inter-mediate
rinse
Inter-mediate
rinse
Inter-mediate
rinse
Programme selectionThe most appropriate programme can beidentified by comparing the type ofcrockery, cutlery, etc., as well as theamount and condition of food remains,
with the details contained in theprogramme overview.
You will find the appropriate programmeinformation in the introduction.
en
17
Washing dishes
Reduce costs!
If only a small number ofdishes have been loaded intothe dishwasher, selecting aprogramme that operates atthe next lowest temperaturewill usually suffice.
Programme dataThe programme specifications can befound in the summary of instructions.Programme specifications refer to normalconditions. Greater deviations may occurdue to:
different amounts of dishestemperature of mains water supplypressure of mains water supplyambient temperaturefluctuations in mains voltagemachine-related factors (e.g.temperature, water volume, ...).
Energy and water consumption is reducedby up to 1/4 when dishes are washed inthe upper basket only.Water consumption values are based on awater hardness setting of 4.
Aqua sensor ** some modelsThe Aquasensor is an optical measuringdevice (light barrier) which measuresthe turbidity of the rinsing water.The Aqua sensor is used accordingto the programme. When the Aqua sensoris active, “clean” rinsing water may betransferred into the next rinsing bathand/or the temperature adjusted. If theturbidity is greater, the water is drainedand is replaced with fresh water. In thisway water consumption can be reducedby approx. 4 litres.
Switching the dishwasher ONTurn on the tap.Set main switch 1 to ON.Indicators light up according to the lastprogramme that was selected.This same programme will run again ifno other programme button 9 ispressed.The numerical display 2 shows theexpected duration of the programme.The programme starts automatically.
Remaining running time displayWhen the appliance has started, theexpected programme running time isdisplayed. The programmed running timeis affected by the water temperature, thenumber of dishes, as well as the degreeof soiling. If these conditions are changed,the running time (depending on theselected programme) can vary greatly.As the effect is not detected until aprogramme is running, the time maybe longer or shorter than expected.
Time delay ** on applicable modelsYou can delay the start of the programmein 1-hour steps up to 19 hours.
Switch on the appliance.Press the timer programming button
3 until the digital display 2 jumpsto .
Keep pressing the timer programmingbutton until the required time isdisplayed.To delete the timer programming,keep pressing the button until is displayed.You can change your programmeselection at any time until theprogramme starts.
End of programmeThe programme has ended when a figure
appears in the numerical display 2 .
en
18
Switching the dishwasher OFFSeveral minutes after the programme hasended:
Set the main switch 1 to OFF.Turn the water tap off.(Does not apply when Aqua-Stop unithas been fitted)Remove dishes, etc. when they havecooled down.
At the end of the programme please openthe door fully and not partially whenemptying the dishwasher. Any escapingwater vapour could damage sensitiveworktops.
Interrupting the programmeSwitch off the main switch 1 .
The lit display goes out. The programmeis saved.If there is a warm water connection or ifthe machine has already heated up andthe appliance door was opened, leavethe door open for several minutes andthen close. Otherwise, expansion maycause the appliance door to spring open.
Switch on the main switch again.
Terminating the programme(Reset)
Simultaneously press programmebuttons A and C for approx. 3 sec.
The numerical display indicates .
The programme sequence lastsapprox. 1 min.
Switch off the main switch 1 .
Changing the programmeWhen the appliance is switched on, theprogramme can be changedwithin minutes.If the programme is changedsubsequently, programme sections(e.g. Cleaning) which have already startedrun to the end. The new remaining timeconsists of the remaining time of theprevious programme section and theremaining time of the newly selectedprogramme.
Intensive dryingIn the final rinse the appliance operatesat a higher temperature and therefore animproved drying result is obtained.(Caution if utensils are fragile!)
Close the door.Hold down programme button A andpress main switch until 1 the digitaldisplay illuminates.Release both buttons.
The LED for button A flashes andthe digital display 2 displays the factorysetting (off) or (on).
To change the setting, pressprogramme button A .Switch off the main switch 1 .
en
19
Additional functions *
* on some models additional functions4 can be set with the buttons.
Saving time (VarioSpeed) *The >>Save time<< function can reducethe running time by approx. 20% to 50%depending on the selected rinseprogramme. The particular change inthe running time is indicated on the timeremaining display. To obtain optimumcleaning and drying results at a reducedrunning time, water and energyconsumption are increased.
Half load*If you have only a few items to wash (e.g.glasses, cups, plates), you can switch to“Half load”. The “half load” additionalfunction saves water, energy and time. It isrecommended to put a little less detergentin the detergent dispenser than for a fullload.
Soaking *The soaking cycle runs before the mainprogramme and must be selected beforethe programme starts. In this additionalprogramme cooking utensils, e.g. pans,bowls, etc., can be soaked and prerinsedin the bottom basket.It is recommended to put approx. 5 g ofdetergent on the door.
Maintenance and care
A regular inspection and maintenance ofyour machine will help to prevent faults.This saves time and prevents problems.
Overall condition of themachine
Check washing chamber for greaseand limescale deposits.
If you find such deposits:Fill the detergent dispenser withdetergent, start the appliance withoututensils in the programme which hasthe highest wash temperature.
Clean the appliance with detergents/appliance cleaners which are particularlysuitable for use with dishwashers.
Regularly wipe the door seal with adamp cloth.
Never use a steam cleaner to clean yourdishwasher. The manufacturer is not liablefor any consequential damage.Regularly wipe the front of the applianceand panel with a damp cloth; water anda little washing-up liquid will suffice.Do not use sponges with a rough surfaceor abrasive detergents, as these couldscratch the surfaces.
Attention!Never use other chlorinated householddetergents! Health hazard!
Salt and rinse aidCheck the refill indicators 6 7 .If required, top up the salt and/or rinseaid.
en
20
FiltersWaste which is deposited on the filters28 may result in a blockage.
After each washing cycle check thefilters for residue.Unscrew the filter cylinder and removethe filters. The filters are permanentlyattached to each other and cannot bedismantled.Remove large foreign objects. Cleanthe filters under running water.
Re-installation:Insert the filters and screw the filtercylinder tight.
Spray armsLime and remnants of food in the washingwater can block the nozzles in the sprayarms 22 and 24 and the armmountings .
Inspect the nozzles in the spray armsfor blocked holes due to remnants offood.If necessary, pull the lower arm 24
upwards and lift it off.Unscrew the upper spray arm 22 .Clean both spray arms under runningwater.Refit the spray arms. Ensure that thelower arm has locked into place and theupper one is screwed tight.
Spray arms
en
21
Waste water pump ** some modelsLarge food remnants in the rinsing waternot retained by the filters may block thewaste water pump. The rinsing water isthen not pumped out and covers the filter.In this case:
Set the main switch 1 to OFF.Scoop out any water.Remove the filters 28 .Remove the cover.
Check the inner compartment forforeign objects and, if required,remove foreign objects.Re-insert the cover.Re-insert the filters and screwinto position.
2
click
3
en
22
Fault finding
Resolving minor problemsyourselfExperience has shown that you canresolve most problems that arise duringnormal daily usage yourself, withouthaving to call out a service engineer. Notonly does this save costs, but it alsomeans that the appliance is available foruse again that much sooner. The followinglist of common occurrences and theirremedies should help you identify thecauses of most problems.
Problems ...
Attention
Remember: Repairs may becarried out by a technician only.If a component has to be replaced,ensure that only original spareparts are used. Improper repairsor use of non-original spare partsmay cause considerable damageand put the user at considerablerisk.
... when the applianceis switched on
The appliance does not start.The mains fuse has tripped.The appliance plug has not beeninserted.The appliance door has not beenshut properly.The tap has not been turned on.The filter on the water supply hoseis blocked.Switch off the appliance and pullout the mains plug. Turn off thetap. Then clean the filter which issituated at the connection of thesupply hose. Finally, restore thepower, turn on the tap and switchon the appliance.
en
23
... with the appliance itselfLower spray arm rotates withdifficulty
Spray arm is blocked by smallitems or food remains.
Lid in detergent compartmentcannot be closed
Detergent compartment has beenoverfilled.Mechanism is clogged withremnants of detergent.Indicator lamps do not extinguishafter washing has finished.
“Check water supply” display 8
lights up.Tap turned off.Water supply interrupted.Filter in the water supply blocked.Supply hose kinked.Pump is jammed.
Remnants of detergent stuck insidedispenser
Compartment was damp when itwas filled up with detergent.Compartment must be dry beforedetergent is added.
Indicator lamps do not extinguishafter washing has finished
Main switch is still set to ON.
Refill display does not light up.Rinse aid refill indicator switchedoff. (see auto 3in1 chapter)Salt refill indicator switched off.(see auto 3in1 chapter)
Water remains inside applianceafter programme has ended
Blockage or kink in drainage hose.Pump is jammed.Filters are blocked.The programme is still running.Wait for the programme to end(numerical display will indicate 0).Perform “Reset” function.
... during washingUnusual amount of foam is created
Normal washing up liquid hasbeen poured into the rinse-aidcontainer.Remove any spilled rinse aid witha cloth as it could otherwise leadto excessive foaming during thenext washing cycle.
Appliance stops suddenly whilewashing is taking place
Cut in electricity supply toappliance.Water supply has beeninterrupted.Implement the “RESET” function.
Knocking sound can be heardwhile washing is taking place
A spray arm is knocking againstthe dishes inside the appliance.
Rattling sound can be heard whilewashing is taking place
Crockery has not been stackedproperly inside the appliance.
Knocking sound coming from inletvalves
This is caused by the way thewater pipes have been laid and ithas no effect upon the way theappliance functions. There is noremedy for this.
en
24
... with the dishes, cutlery, etc.Remnants of food are stuck to thedishes, cutlery, etc.
Dishwasher was not loadedproperly. Jets of water could notreach all parts of the dishes, etc.Too many items in the rack.Items in the rack were touchingeach other.Not enough detergent was addedto dispenser.Selected wash programme wasnot intensive enough.Rotation of spray arm wasobstructed by dish, etc.Nozzles in spray arm are blockedby remnants of food.Filters are blocked.Filters have been incorrectly fitted.Waste-water pump is jammed.
Plastic items are discolouredNot enough detergent was addedto dispenser.
White stains are left on crockery,glasses have a milky appearance
Not enough detergent was addedto input compartment.Amount of rinse-aid was set toolow.Although water is quite hard, nosalt has been put in appliance.Water softener was set too low.Lid on salt container is notscrewed tight.If you used a phosphate-freedetergent, try a detergentcontaining phosphates andcompare results.
Dishes, cutlery, etc. have not beendried
Selected programme did notinclude drying function.Amount of rinse-aid was set toolow.Items were removed fromdishwasher too soon.
Glasses have a dull appearanceAmount of rinse-aid was set toolow.
Tea stains or traces of lipstick havenot been completely removed
Detergent does not have asufficient bleaching effect.Washing temperature was set toolow.
Traces of rust on cutleryCutlery is not sufficiently rustproof.Salt content in washing water istoo high.
Lid on salt container is notscrewed tight.Too much salt was spilt whilefilling container.
Glasses become clouded anddiscoloured; coating cannot bewiped off
Unsuitable detergent was used.Glasses are not dishwasher-proof.
Smears left behind on glasses andcutlery; glasses have acquired ametallic appearance
Amount of rinse-aid set too high.
en
25
Customer Service
Please call your local service agent, if youare not able to resolve any problemyourself. The name of your nearest serviceagent is shown in the Customer Serviceaddress list. When you call, please providedetails of the model number (1) and theproduction (FD) number (2) which areshown on the nameplate 33 on theappliance door.
FD
1
2
Warning
Please note that a visit by thecustomer service technician inthe event of a fault or one ofthe problems previouslydiscussed is not free of chargeeven during the warrantyperiod.
Information
Notes on comparison testsYou will find details of the conditions forthe comparison tests on the additional”Notes on comparison tests” sheet. Theconsumption values for the relevantprogrammes are given in the introduction.
GeneralBuilt-under and integrated applianceswhich are subsequently installed asfree-standing appliances must besecured to prevent them from fallingover, e.g. by screwing them to the wallor by installing them under a continuousworktop which is screwed to theadjoining units.For Swiss version only:The appliance can be installed withoutdifficulty between wooden and plasticwalls in a kitchen range. If the applianceis not connected via a plug, theinstallation side must feature an all-poledisconnector with a contact gap of atleast 3 mm in order to satisfy therelevant safety regulations.
en
26
Installation
The dishwasher must be connected bya qualified technician to ensure correctoperation. The specifications for supply,drainage and connected load must fulfilthe required criteria as stated in thefollowing paragraphs or in the installationinstructions.
Install the appliance in the followingsequence:– Check the delivery– Install the appliance– Connect the waste water– Connect the fresh water– Connect the power supply
DeliveryYour dishwasher was checked at thefactory to ensure that it was in perfectworking order. This may have left somesmall water stains in the dishwasher.These will disappear after the first rinsecycle.
InstallationThe required installation dimensions canbe found in the installation instructions.Level the appliance with the aid of theheight-adjustable feet. Ensure that theappliance is situated securely on the floor.If the appliance is installed undera worktop, tension the appliance onlylightly against the worktop with theheight-adjustable feet.
Waste water connectionSee the installation instructions for therequired connection steps. If required,attach a siphon with drainage spigot.Using the enclosed parts, connect thewaste water hose to the drainage spigotof the siphon.Ensure that the drainage hose is notkinked, crushed or twisted (ensure thatthere is no sealing cover which preventsthe waster water from flowing away!).
Fresh water connectionUsing the enclosed parts, connect thefresh water connection to the tapaccording to the installation instructions.Ensure that the fresh water connection isnot kinked, crushed or twisted.When replacing the appliance, alwaysconnect a new water supply hose to thewater supply. The old supply hose mustnot be re-used.
Water pressure:Minimum 0,05 MPa (0,5 bar) – maximum1 MPa (10 bar).If the water pressure is higher, install apressure reducing valve.
Flow rate:Minimum of 10 litres per minute.
Water temperature:We recommend that you use cold water.If you do use hot water, the temperatureshould not exceed 60 °C.
Electrical connectionConnect the appliance only to 230 Valternating current via a correctly installedsocket with protective conductor.See rating plate for required fusing 33 . The socket must be attached near thedishwasher and be freely accessible.The connection may be modified by anelectrician only.Use only a residual-current-operated
circuit-breaker which features the symbol. Only this circuit breakerguarantees compliance with the currentlyvalid regulations.
Removing the applianceIt is essential, when removing theappliance, to observe the followingsequence: First, disconnect the appliancefrom the power supply.Pull out the mains plug.Turn off the water supply.Disconnect the waste water and freshwater connections.Loosen the fastening screws under theworktop. If fitted, remove the base panel.Pull out the appliance, carefully pulling thehose behind.
en
27
Transporting the dishwasherDrain water from the dishwasher. Secureall loose parts. The appliance should onlybe transported in an upright position.
If the appliance is not kept uprightduring transport, any water left insidemay seep into the control module andcause subsequent errors withprogramme functions.The appliance must be drained in thefollowing sequence:
Turn on the tap.Close the door.Set main switch to ON.Select the B programme. Theprogramme duration in minutes isshown in the numerical display.Wait for approximately 4 minutes.Terminate the programme bypressing A and Csimultaneously.The time display changes to .
Wait a further minute and thenswitch the appliance off.Turn off the tap.
Protection from freezingtemperaturesIf the appliance is installed in a locationwhere there is a risk of freezingtemperatures (e.g. in a holiday home), allwater must be completely drained out ofthe interior (see “Transporting thedishwasher”).Turn OFF the tap, disconnect the supplyhose and allow to drain.
Waste disposal
DisposalOld appliances are not worthless rubbish.Valuable raw materials can be reclaimedby recycling old appliances.Pull out the mains plug of the redundantappliance. Cut off the power cord anddiscard with mains plug.To prevent children from lockingthemselves in the appliance andsuffocating, destroy the door lockand childproof lock (if fitted).You received your new appliance ina protective shipping carton. All packagingmaterials are environmentally friendly andrecyclable.Please contribute to a better environmentby disposing of packaging materials in anenvironmentally-friendly manner. All plasticparts of the appliance are identified byinternationally standardised symbols(e.g. >PS< polystyrene).When the appliance is being disposed of,the plastic waste can be sorted forenvironmentally-friendly recycling.Please ask your dealer or inquire at yourlocal authority about current means ofdisposal.
en
28
Disposal of the packagingPlease dispose of the packagingmaterial in an environmentallyfriendly manner.Keep children away from shippingcarton and packaging components.Danger of suffocation from foldingcartons and plastic film.� Corrugated cardboard consists
mainly of wastepaper.� The moulded polystyrene parts do
not contain anychlorofluorohydrocarbons.
� The polyethylene film (PE) consistspartly of secondary raw materials.
� The wooden frames (if fitted) aremade of untreated residual wood.
� The hoops (if fitted) consistof polypropylene (PP).
Disposal of redundantappliances
Make redundant appliances unusableto prevent subsequent accidents.Dispose of the appliance in anenvironmentally friendly manner.
WarningChildren could become locked in theappliance (risk of suffocation) or findthemselves in other dangerous situations.Therefore: Pull out the mains plug, severand dispose of the power cord.Destroy the door lock so that the doorcan no longer be closed.
This appliance is labelled in accordancewith European Directive 2002/96/EGconcerning used electrical and electronicappliances (waste electrical and electronicequipment – WEEE). The guidelinedetermines the framework for the returnand recycling of used appliances asapplicable throughout the EU.
en
23
en Subjekt to modification
en
23
en Subjekt to modification
40 Switch on the child-proof lock 41 Open the door with child-proof lock
switched on42 Switch off the child-proof lock
When the door is open, the child-proof lockoffers no protection.
Child-proof lock *
Large sheets or grilles and plates which have a diameter greater than 30 cm (gourmetplates, pasta plates, dinner plates) can be cleaned with the aid of the spray head.To do this, remove the top basket and insert the spray head as illustrated in the diagram.
To ensure that the spray jet can reach all parts, arrange the baking sheets as illustrated(max. 4 baking sheets and 2 grilles).
Never operate the dishwasher without the top basket or baking sheet spray head!
Baking sheet spray head *
* some models
���� �� ��� �� ��������
AQUA-STOP guarantee
(does not apply to appliances without Aqua-Stop)
In addition to warranty claims against the seller based on thepurchase contract and in addition to our appliance warrantywe will pay damages under the following conditions:
1. If our Aqua-Stop system is defective and causes waterdamage, we will make good the damage for private users.
2. This liability guarantee is valid for the service life of theappliance.
3. A prerequisite for the warranty claim is that the appliancehas been correctly installed and connected with Aqua-Stopaccording to our instructions. “This also includes the correct installation of the Aqua-Stopextension (original accessory).” Our warranty does not extend to defective feed lines or fittingsup to the Aqua-Stop connection on the tap.
4. If your appliance is fitted with Aqua-Stop, you can leave yourappliance unattended during operation and leave the tapturned on afterwards. The tap should only be turned off if youare absent from home for a prolonged period, e.g. severalweeks holiday.
Siemens-Electrogeräte GmbHCarl-Wery-Straße 34, 81739 München
�� ��� �� ������� ��� ��� ������ �����
GB 0844 / 8928999
IE 01450 2655
Calls from a BT landline will be charged at up
to 3 pence per minute.A call set–up free of up to 6 pence may apply.
Pease find the contact data of all countries in the enclosedcustomer service list.
Internet: www.siemens–home.com
