Date post: | 29-Dec-2015 |
Category: |
Documents |
Upload: | georgina-harrington |
View: | 217 times |
Download: | 2 times |
Engineering Low-Head Dams for Function and Safety
Fritz R. Fiedler
Department of Civil Engineering
University of Idaho
What is a Low-Head Dam?
• A dam that is typically less than 15 feet tall
• Used to pond water behind them but not control flow
• Head: a term that refers to elevation, which can be related to fluid pressure and energy
Why are they dangerous?
• Low-head dams cause water to recirculate, thus trapping buoyant objects
• Side view
• Front view
Flow in rectangular channels
QV y
w
Variables:y = flow depth (L)w = channel width (L)A = flow area = yw (L2)V = flow velocity (L/T)Q = discharge = VA (L3/T)q = Q/w (L2/T)
Example:y = 2 ftw = 1.5 ftA = 3 ft2
V = 3 ft/sQ = 9 ft3/sq = 6 ft2/s
States of flow in open channels
• For a given Q, flow in open channels can be subcritical, supercritical, or critical– Subcritical: disturbances on water surface will
travel upstream (flow velocity less than wave velocity); high y, low V
– Supercritical: disturbances will not travel upstream (flow velocity greater than wave velocity); low y, high V
– Critical: flow velocity equals wave velocity
Hydraulic Jump
12
Q = V1A1
= V1y1w
Image source: http://www.engineering.usu.edu/classes/cee/3500/openchannel.htm
Hydraulic Jump
Q = V2A2
= V2y2w
Note: Q is constant, so V1y1 = V2y2 (if w constant also)
• Ratio of inertia forces to gravity forces
• F = V / (gy)0.5
• G = gravitational acceleration• Subcritical flow: F < 1 (gravity forces larger)• Supercritical flow: F > 1 (inertia forces larger)• Critical flow: F = 1
Froude Number
Froude Number
12
Image source: http://www.engineering.usu.edu/classes/cee/3500/openchannel.htm
Hydraulic Jump
F1 = V1 / (gy1)0.5
F1 > 1F2 = V2 / (gy2)0.5
F2 < 1
Initial and Sequent Depths
• Relationship between depths before (initial) and after (sequent) a hydraulic jump
• If y1 and V1 are known, can compute y2
211
2 8F112
1
y
y
Flow over a dam (weir)
y0
y2y1
ycHydraulic
JumpP
H
As water flows over dam, goes through critical depth, yc at which F = 1
Q = CwH1.5 or q = CH1.5
where C is a weir coefficient that varies with dam type and H – but we are going to find and measure yc
subcriticalsupercritical
subcritical
Critical Flow
• At critical flow, F = 1 = Vc / (gyc)0.5
• Vc = (gyc)0.5
• Measure yc at dam, compute Vc then
• Q = Vcycw
• How is the location of yc found?
Submerged Hydraulic Jump
y0
y2y1
yc
P
H
yt
• When yt exceeds y2 the jump becomes submerged• Degree of Submergence = S = (yt – y2) / y2
• When S < 0, jump occurs downstream• When S > 0, jump is submerged• If yt becomes large enough, dam will be submerged too• In the flume, we can control yt
y0
P
H yc
waves travel upwaves travel down
y1yt
y2
y
Project Steps
1. Analysisa. Measure variables at two discharges
b. With and without tailwater submergence
2. Designa. Objectives: maintain upstream depth, allow
safe passage, create surf wave, minimize cost
b. Method: simple calculations, physical model studies and testing
Analysis1. At low discharge
a. With no tailwateri. Measure: H, P (dam height), yc (must locate), y1,
y2, y
ii. Compute: Vc, Q, q, F1, C
iii. Evaluate: measurement accuracy, sequent depth equation, floating object passage
b. With tailwater submerging jumpi. Measure: yt, y, and compute S
ii. Evaluate: measurements, floating object passage
2. Repeat 1., a., b., … for high discharge
Notes
• We can mark, with tape and markers, the water levels right on the flume
• Mark the height of the tailwater gate
• We will keep flume slope, discharges constant throughout semester
• Group Assignment: create a data sheet based on previous slide before next class.
Design1. Conceptual
a. What makes the hydraulic dangerous?i. Uniformity, y, reverse flow velocity, aeration
b. How can this knowledge be used to meet objectives?
2. Analytical / Mathematicala. Difficult!
b. Computer models
c. Simple equations (e.g., V-notch weir)
3. Physical models…
Physical Models
Image source: http://www.usbr.gov/pmts/hydraulics_lab/about/index.html
Physical Model Testing• Measure variables as in Analysis (and more?)
– What has changed?
• Compare upstream pool elevations– Aim for little or no difference at both discharges
• Test object passage– Surf spot?
• Describe the hydraulic
• Iterative process! (a.k.a., trial and error)
Practicality and Economics
• What types of materials would be required to build your design? (concrete, rip rap, …)
• How and when could it be constructed?• If volume of material added is the primary cost,
and the cost of this material per unit volume is known – how much would it cost?
• Minimum volume = minimum cost: estimate the volume change in your design
Other (Important) Considerations
• Water Quality– Sediment and contaminants
• Physical– Sediment and stream morphology– Dissolved oxygen– flooding
• Ecological– Fish passage– Effects on aquatic life