A Corning® Solutions Product
Individual 12-fiber modules
Integrated splice capability
Modules extend/retract independently
Top and rear strain-relief
Reduced fiber routing density
Improved density
Maximize scalability and modularity
Enables on-frame splicing without sacrificing density when using standard EMF modules
Minimizes connector disturbance
Ensures bend-radius control
Reduce fiber trough build by 91% when using EMF-MTP® Housings
Increased density with EMF-Pretium EDGE® Housings and modules with LC Connectors - 2,304 fiber terminations
features and benefits | The Enhanced Management Frame (EMF) is designed for FTTx, cross-connect and interconnect applications. The integrated modular design allows growth and expansion of a fiber management system one frame, one module and one fiber termination at a time. User-friendly features such as single jumper length, in-bay jumper storage, transparent modules and multiple inter-bay routing options make this frame an ideal solution for both FTTx deployments and traditional cross-connect and interconnect applications.
The EMF utilizes a single 12-fiber module that may be configured with splitters/couplers and wavelength division multiplexers (WDMs) that support today’s FTTx passive optical networks. Other module options include pigtailed, stubbed, empty and with adapters only. Each module extends and retracts independently from the frame for minimal adjacent connector disturbance and a “quiet-front” appearance. Splicing facilities within the module maintain the maximum 1728-fiber terminations with SC and LC connectors. By splicing off the frame and specifying EMF-Pretium EDGE housings/modules and LC connectors, frame density increases to 2,304 fiber terminations.
Integrated fiber management within modules will store 3 m of buffer tube or ribbon slack and 1 m of 900 µm pigtail slack.
Factory-stubbed termination modules and housings are available for both the left and right side of the frame. By specifying the EMF-MTP housings on the left and right side of the EMF frame, the quantity of individual fiber jumpers can be reduced from 1,728 to 144 with 12-fiber MTP module stubs.
Enhanced Management Frame | Photo FOH003
Enhanced Management Frame (EMF)
|
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|
SPECIFICATION SHEET EVO-278-EN | PAGE 1
A Corning® Solutions Product
Enhanced Management Frame (EMF)
SPECIFICATION SHEET EVO-278-EN | PAGE 2
Inter-bay jumper slack storage enables the use of a single jumper length, minimizing the variation of jumper length. Staggered side-mounted routing guides on the module housings allow clean fiber management and control pathways for front-to-rear jumper routing. There is full bend-radius control throughout the frame with top and rear strain-relief.
Open Top for Easy Interconnection Routing
Top Cable Strain-Relief
Integrated IBU for Single- Jumper-Length Slack Storage
Optional Full-Length Rear Troughing System
Full Radius Control for Minimum-Bend- Radius Protection Throughout Frame
Protective Lower Fiber Cover
Wide Fiber Routing Area with Separate Routing Zones
Enhanced Management Frame | Photo FOH004
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 3 |
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
EMF Housing | Photo FOH035EMF Housing with Pretium EDGE® Module | Photo LAN2325
EMF Module | Photo FOH032
Module Handle Folds Down for Enhanced Connector Access
Individual 12-Fiber Access from Sliding Module Full Radius Control
Transparent Module for Easy Internal Inspection
Front-Loading Housing; Six 12-Fiber Modules in each Housing Terminate 72 Fibers
Staggered Side-Routing Guides Prevent Jumper Stack-Up
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 4
Enhanced Management Frame (EMF)
Left Module (Top View) | Drawing ZA-926
72 Left Modules and72 Right Modules
per Frame
6 Left Modules and6 Right Modules
per Housing
Modules per Housing and Frame | Drawing ZA-921
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12
EMF- Pretium EDGE®
Left-Hand ModuleEMF- Pretium EDGERight-Hand Module
EMF - Pretium EDGE Housing
Left Module (Bottom View) | Drawing ZA-931
EMF-Pretium EDGE® Housing | Drawing ZA-3873
*Note: For adapter part numbers, see page 6.
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 5 |
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
EMF Module, 12-Fiber | Photo FOH011
Housings and Modules Housings and modules for the EMF are available in four configurations: •Empty •Loadedwithadaptermodules •Pigtailed •Stubbed
Housings and modules for the EMF-Pretium EDGE®
are available in two configurations: •Empty •Loadedwithmodules
specifications |
Adapter Capacity
Adapter Terminations Terminations Terminations Type per Module per Housing per Frame
SC 12 72 1,728 LC 12 72 1,728 FC 12 72 1,728 LC 12 96 2,304
Dimensions (H x W x D) cm (in)
13.97 x 21.92 x 29.84 (5.5 x 8.6 x 11.75)
13.97 x 21.92 x 29.84 (5.5 x 8.6 x 11.75)
Description
Empty Left EMF Housing; holds 6 EMF modules
Empty Right EMF Housing; holds 6 EMF modules
Empty Left-Hand Housing with MTP® option, holds 6 EMF modules
Empty Right-Hand Housing with MTP option, holds 6 EMF modules
Empty Left EMF-Pretium EDGE Housing, holds 8 Pretium EDGE modules
Empty Right EMF-Pretium EDGE Housing, holds 8 Pretium EDGE modules
Part Number
Housings – Empty
CCF-CML-072
CCF-CMR-072
CCF-CML-07289
CCF-CMR-07289
CCF-CML-96EDGE
CCF-CMR-96EDGE
ordering information |
A Corning® Solutions Product
ordering information | (continued)
Enhanced Management Frame (EMF)
SPECIFICATION SHEET EVO-278-EN | PAGE 6
Dimensions (H x W x D) cm (in)
13.97 x 21.84 x 29.84 (5.5 x 8.6 x 11.75)
13.97 x 21.84 x 29.84 (5.5 x 8.6 x 11.75)
Description
Left EMF Housing with adapters and modules installed
Right EMF Housing with adapters and modules installed
Part Number
Housings – Loaded with Modules and Adapters
CCF - CML - |1 |2
CCF - CMR - |1 |2
|1Select number of fibersrequiring adapters.00 = Empty module 01-12 = 1-12 adapters
|2Select adapter code.Single-Mode 3C = SC ultra 6C = SC angled A9 = LC duplex ultra B3 = LC duplex angled
Multimode 39 = SC A7 = LC duplex
Notes: 1) Maximum SC adapter capacity is 12 per module.
2) Maximum LC adapter capacity is 6 duplex per module.
Part Number Example
Part Number
CCF-CML-726C
Description
Left EMF Housing loaded with modules, 72 SC APC adapters installed
Single Adapter Only Part Numbers
Part Number
ADP-SC00-CCGDF-CLS ADP-SC00-CCNDF-CLS ADP-DLC0-CCGRC-CLS ADP-DLC0-CCNRC-CLS ADP-FC00-MMXTH-NLS
Description
Adapter, SC APC simplex with mounting clip
Adapter, SC UPC simplex with mounting clip
Adapter, LC APC duplex, reduced flange, integral clip
Adapter, LC UPC duplex, reduced flange, integral clip
Adapter, FC UPC, threaded flange
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 7 |
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
ordering information | (continued)
2.24 x 21.92 x 29.84 (0.9 x 8.6 x 11.75)
2.24 x 21.92 x 29.84 (0.9 x 8.6 x 11.75)
Description
Left Module with adapters installed; specify adapter provision type from charts below
Right Module with adapters installed; specify adapter provision type from charts below
Part Number
Modules – Loaded with Adapters
CCML - |1
Part Number
Left-Hand EMF 12-Port Module with MTP® Cable Assembly
Right-Hand EMF 12-Port Module with MTP Cable Assembly
EMF - MTP® Modules
CCML1203 - MT00C
CCMR1203 - MT00B
|1
|1
|2
CCMR - |1 |2
Part Number Example
Part Number
CCML12-6C
CCMR06-B3
CCMR00-A7
Description
Left EMF Module with 12 SC APC adapters installed
Right EMF Module with 6 LC APC adapters installed
Right EMF Module - Empty (no adapters) - LC type mountings installed for future adapters.
Dimensions (H x W x D) cm (in)
|1Select adapter code.Single-Mode 3C = SC ultra 6C = SC angled A9 = LC duplex ultra B3 = LC duplex angled
Multimode 39 = SC A7 = LC duplex
Note: Stubbed or pigtailed housings are available separately in a wide array of configurations. Each complete housing can accommodate up to six modules. Stubbed or pigtailed modules are also available separately in the same array of configurations. Individual modules can be easily loaded into unused positions within a previously installed housing. Contact your Corning Cable Systems Customer Service Representative for module and housing ordering information at 800-743-2675 or internationally at +1-828-901-5000.
|1Select number of fibersrequiring adapters.00 = Empty module 01-12 = 1-12 adapters
|2Select adapter code.Single-Mode 3C = SC ultra 6C = SC angled A9 = LC duplex ultra B3 = LC duplex angled
Multimode 39 = SC A7 = LC duplex
Notes: 1) Maximum SC adapter capacity is 12 per module.
2) Maximum LC adapter capacity is 6 duplex per module.
EMF module | Photo FOH356 EMF frame | Photo FOH364
A Corning® Solutions Product
Enhanced Management Frame (EMF)
SPECIFICATION SHEET EVO-278-EN | PAGE 8
ordering information | (continued)
Housing and Modules with Pigtails
M - - 1 0
|1Select hardware type.CC = Pigtailed housingCM = Pigtailed module
|2Select hardware mounting side.R = RightL = Left
|6Select mode of operation.R = Single-modeK = Multimode 62.5/125 µm T = Multimode 50/125 µm
|7Select pigtail type.J = RibbonH = MIC® 900 µm buffered fiber
Notes: 1) Housings are shipped individually with a maximum fiber count of 72.
2) Pigtailed modules ship with both Q-Pak and heat-shrink holders.
|3Select total fiber count.01-72 = Enter number Example: 6 fibers = 06 12 fibers = 12 72 fibers = 72See Note 1.
|5Select connector type.Single-Mode3C = SC ultra 6C = SC angled A9 = LC duplex ultra B3 = LC duplex angledMultimode39 = SC 17 = FC A7 = LC duplex
|4Select fiber count of each module.01-12 Example: 6 fibers = 06 12 fibers = 12
|1 |2 |3 |4 |5 |6 |7 |8
Part Number Example
Part Number
CCL72M12-3C-1RJ-0
CMR12M12-6C-1RH-0
Description
Pigtailed Left-Hand EMF Housing, total fiber count is 72 fibers using 12-fibers per module, connectors are SC UPC, pigtail type is a 1 m single-mode ribbon
Pigtailed Right-Hand EMF Module, 12-fibers, connectors are SC APC, pigtail type is 1 m MIC 900 µm buffered fiber
|8Select jumper tracing option.- = No jumper tracingS = SearchLite® Tracing System (SC UPC only)
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 9 |
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
ordering information | (continued)
Pretium EDGE® Modules
ECM - M12 - -
|1Select polarity type.U = UniversalS = Straight-throughSee Note 1.
|2Select LC Duplex adapters on front of modules.04 = Single-mode OS205 = Multimode OM3/OM4
|3Select Pinned MTP® on rear of module.93 = Multimode OM3/OM489 = Single-mode OS2
Note: 1) Universal polarity accounts for 1 send and 1 receive fiber per pair so fiber 1 (send) will come out on fiber 2 (receive) on other end.
Straight-through polarity is most often used with SM fiber using two different wavelengths for send and receive.
|4Select fiber type.R = OS2T = OM3Q = OM4
|1 |2 |3 |4
Pretium EDGE Module with VFL-Compatible| Photo LAN1545
SPECIFICATION SHEET EVO-278-EN | PAGE 10
Enhanced Management Frame (EMF)
ordering information | (continued)
Housing and Modules with Stubbed Cable
- - 1
|1Select hardware type.CCF = 72-fiber EMF housingCCM = 12-fiber EMF module
|2-9Select hardware mounting side.R/B = Right-side housing with cable entry at top rightL/C = Left-side housing with cable entry at top left
|6Select fiber type.- = Single-modeK = Multimode 62.5/125 µm T = Multimode 50 CC
|7Select cable type.900 µm Coated Fiber Cables81 = MIC® Riser Indoor Cable with TBII® Buffered Fiber 88 = MIC Plenum Cable with Flexible TBII Buffered Fiber 250 µm Coated Fiber Loose Tube Cables (2-144 fibers)W4 = ALTOS® All-Dielectric Outside Plant Cable W5 = ALTOS Single-Armored Outside Plant Cable W6 = ALTOS Double-Armored Outside Plant Cable W7 = ALTOS Riser Cable WZ = ALTOS LSZH™ Cable WF = FREEDM® Indoor/ Outdoor Cable Ribbon Fiber Cables (12-144 fibers)C4 = SST-Ribbon™ All-Dielectric Outside Plant Cable C5 = SST-Ribbon Single- Armored Outside Plant Cable C6 = SST-Ribbon Double- Armored Outside Plant Cable C7 = Ribbon riser cable CF = FREEDM Ribbon Riser Indoor/Outdoor Cable
Note: 1) One housing shipped for 1-72 fibers. Two housings shipped for 144 fibers.
2) Not all part number configurations are available. Please confirm availability with a Corning Cable Systems Customer Service Representative.
|3Select total fiber count.01-72 = Enter number E4 = 144 fibers Example: 12 fibers = 12 144 fibers = E4See Note 1.
|5Select connector type.Single-Mode3C = SC ultra 6C = SC angled A9 = LC duplex ultra B3 = LC duplex angledMultimode39 = SC A7 = LC duplex
|4Select cable length in meters.1-99 = Enter number 99+ = Enter alphanumeric code from Table A
|1 |2 |3 |4 |5 |6 |7 |8
Part Number Example
Part Number
CCFL7231-3C-C7SL1C
Description
Left-Hand 72-Fiber Stubbed EMF Housing with 31 m of single-mode ribbon riser cable attached and terminated with SC UPC connectors featuring SearchLite Tracing System adapters; cable enters from the top
|8Select special options.00 = Standard configurationSL = SearchLite® Tracing System (SC UPC only)
|9
|9See selection block 2.
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 11 |
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)A Corning® Solutions Product
|
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
ordering information | (continued)
Description
Left-Hand EMF 72-Port Housing with MTP Cable Assembly
Right-Hand EMF 72-Port Housing with MTP Cable Assembly
Part Number
EMF-MTP Housings
CCML7203 - - MT89C|1
CCMR7203 - - MT89B|1
|1Select adapter code.Single-Mode 3C = SC ultra 6C = SC angled A9 = LC duplex ultra B3 = LC duplex angled
Note: 1) Maximum number of SC adapters per module is 12, per housing is 72 (72 fibers). Maximum number of LC adapt-ers per module is 6 duplex, per housing is 36 (72 fibers)
Table A: Codes for Fiber Counts and Cable Stub Lengths Over 99 A _ = 10_ M_ = 21_ B _ = 11_ N _ = 22_ C _ = 12_ P _ = 23_ D _ = 13_ Q _ = 24_ E _ = 14_ R _ = 25_ F _ = 15_ S _ = 26_ G_ = 16_ T _ = 27_ H _ = 17_ U _ = 28_ J _ = 18_ V _ = 29_ K _ = 19_ W_ = 30_ L _ = 20_
Examples:E4 = 144 fiber A5 = 105 m
Notes: 1) “I” and “O” are not used.2) Lengths from 100 to 339, use single letter plus number (1 to 9).3) Lengths over 339 m can be ordered only in 10 m increments.
X _ = 31_ AH = 410 Y _ = 32_ AJ = 420 Z _ = 33_ AK = 430 AA = 340 AL = 440 AB = 350 AM = 450 AC = 360 AN = 460 AD = 370 AP = 470 AE = 380 AQ = 480 AF = 390 AR = 490 AG = 400 AS = 500
Table B: Standard Cable Types for Stubbed Hardware
Cable Type Code Description Fiber Count Fiber TypeC4 SST-Ribbon™ Dielectric Outdoor Cable 12-144 Single-modeC7 Ribbon riser indoor cable 12-144 Single-modeW4 ALTOS® All-Dielectric Outside Plant Cable 12-144 Single-modeCF FREEDM® Ribbon Riser Indoor/Outdoor Cable 12-144 Single-modeWF FREEDM Indoor/Outdoor Cable 12-144 Single-modeW7 ALTOS Riser Cable 12-144 Single-mode
Note: Max cable size for EMF housings is 144 fibers.
A Corning® Solutions Product
Enhanced Management Frame (EMF)
Dimensions (H x W x D) cm (in)
213.4 x 86.4 x 43.12 (84 x 34 x 17)
30.5 x 86.4 x 43.2 (12 x 34 x 17)
61 x 86.4 x 43.2 (24 x 34 x 17)
137.2 x 86.4 x 43.2 (54 x 34 x 17)
213.4 x 86.4 x 43.2 (84 x 34 x 17)
5.08 x 86.4 x 14.2 (2 x 34 x 5.6)
N/A
86.4 x 43.12 (34 x 17)
Description
7-ft EMF Frame Mounts 12 LH and 12 RH housings
1-ft EMF Frame Extension Kit used to tie a 7-ft frame to overhead rack 8 ft high
2-ft EMF Frame Extension Kit used to tie a 7-ft frame to overhead rack 9 ft high
4.5-ft EMF Frame Extension Kit used to tie a 7-ft frame to overhead rack 11.5 ft high
7-ft EMF Frame with 12 rear troughs attached
Individual Rear Trough for EMF
Zone 4 Mounting Bolt Kit
Isolation Pad Kit for EMF frame (includes mounting hardware)
Part Number
Empty Frame
CCF-FRAME-7
CCF-FRAME-EXT-7-8
CCF-FRAME-EXT-7-9
CCF-FRAME-EXT-7-11
CCF-BAY-7
CCF-JT-REAR
QFMABK1A
CCF-PAD-KIT
ordering information |
4.5 Ft EMF Extention
ZA-3598
4.5 ft EMF Extension Kit (CCF-FRAME-EXT-7-11) | Drawing ZA-3598
Network Bay FrameEnhanced Management Frame (EMF)
ZA-3599
EMF Frame (CCF-FRAME-7) | Drawing ZA-3599
SPECIFICATION SHEET EVO-278-EN | PAGE 12
A Corning® Solutions Product
|
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
Dimensions of Cable Opening(Diameter) cm (in)
8 (0.32)
1.05 (0.40)
1.3 (0.50)
1.6 (0.63)
1.75 (0.70)
2.05 (0.80)
2.06 (0.81)
N/A
N/A
Description
Cable Strain-Relief Grip
Cable Strain-Relief Grip
Cable Strain-Relief Grip
Cable Strain-Relief Grip
Cable Strain-Relief Grip
Cable Strain-Relief Grip
Large Cable Strain-Relief Bracket, for cable dimensions above 0.81-in. Includes 1 bracket and all supporting hardware
Cable Clamp Assemblies, hold up to 3 cables; order strain-relief grips separately
Cable Bonding Kit; includes four 14-in ground wire assemblies, one 4-position ground bar and hardware to bond cables to frame ground
Part Number
A0388952
A0388954
A0388955
A0388956
A0388957
A0388958
CCF-LRG-CAB-BKT
A0375902
A0388959
ordering information | (continued)
Notes: 1) Strain-relief components not required when using housings.2) Each EMF Frame ships with 12 cable clamp assemblies. Strain-relief grips are sold separately.
Strain-Relief Components for Front Strain-Relief
EMF Cable Clamp Assemblies | Drawing ZA-3291
Cable Strain Relief Bracket
ZA-3600Large Cable Strain-Relief Bracket (CCF-LRG-CAB-BKT) | Drawing ZA-3600
Cable Strain-Relief Grip (see note 2)
Clamps
SPECIFICATION SHEET EVO-278-EN | PAGE 13
A Corning® Solutions Product
Front-Mounting Workshelf EMF front-mounting workshelf provides a convenient workspace for craft persons. The shelf is capable of supporting up to 50 lbs.
EMF Workshelf | Photo FOH026
ordering information |
Description
Front-Mounting EMF Workshelf
EMF Service Module Bracket
Part Number
CCF-SHELF
P0707979
SPECIFICATION SHEET EVO-278-EN | PAGE 14
Enhanced Management Frame (EMF)
36.2 x 85 x 38 (14.25 x 33.5 x 15)
3.0 x 6.0 x 12.0(7.6 x 15.2 x 30.5)
Dimensions (H x W x D) cm (in)
A Corning® Solutions Product
Enhanced Management Frame (EMF)
|
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|
EMF Optical Components The EMF FTTx splitter module allows for deployment of passive optical network (PON) architecture with the optical splitter in a central office frame. It is available in dual 1x16 or 1x32. Available only in LC APC and LC UPC. The EMF course wavelength division multiplexing (CWDM) modules are available in SC APC and SC UPC. EMF splitter modules occupy two positions inside the EMF housings; CWDM modules occupy one position. The modules are designed to meet applicable sections of Telcordia GR-1209-Core and GR-1221-Core.
X
Y
Z
1 x 32 Splitter Module
ZA-3329
EMF 1x32 Splitter Module | Drawing ZA-3329
ordering information |Description
EMF Left-Hand 1x32 Splitter Module with LC APC single-mode input/output adapters
EMF Right-Hand 1x32 Splitter Module with LC APC single-mode input/output adapters
EMF Left-Hand Dual 1x16 Splitter Module with LC APC single-mode input/output adapters
EMF Right-Hand Dual 1x16 Splitter Module with LC APC single-mode input/output adapters
EMF CWDM Demultiplexing Right-Hand Module; 9 IN, 1 OUT; SC UPC
EMF CWDM Demultiplexing Right-Hand Module; 9 IN, 1 OUT; SC APC
EMF CWDM Multiplexing Right-Hand Module; 1 IN, 9 OUT; SC UPC
EMF CWDM Multiplexing Right-Hand Module; 1 IN, 9 OUT; SC APC
Part Number
MLS1AAB30B301132
MRS1AAB30B301132
MLS1AAB30B302116
MRS1AAB30B302116
MRC1AA3C03C01ZZZ
MRC1AA6C06C01ZZZ
MRC1AA3C03C01XXX
MRC1AA6C06C01XXX
Jumpers 2.0 mm jumpers recommended length within frame is 5.5 m. See EVO-29-EN for ordering information. See SRP 003-599 for additional jumper recommendations.
Part Number Example
Description
SC-SC single-fiber, 2.0 mm jacketed cable assembly
Part Number
444401R2131005M
SPECIFICATION SHEET EVO-278-EN | PAGE 15
A Corning® Solutions Product
Inter-Bay Distribution (IBD) EMF inter-bay distributors are designed to be placed between two EMFs and are used to store and manage jumper slack. They each require a 5-in gap between frames for mounting.
End Cap and Door Cover EMF end caps protect the end of a bay line-up while providing a clean, finished appearance. A dual door front cover provides individual access to the left or right column of termination housings.
EMF_IBD_Install
ZA-3251
EMF Inter-Bay Dual Storage Unit (IBD) | Drawing ZA-3246
EMF_End Cap_Install
ZA-3250
EMF End Cap | Drawing ZA-3250
EMF Dual Door Front Cover - Install
ZA-3246
EMF Dual-Door Front Cover | Drawing ZA-3251
Dimensions(H x W x D) cm (in)
213.4 x 12.7 x 30 (84 x 5 x 12)
213.4 x 12.7 x 30 (84 x 5 x 12)
206 x 86.4 x 2.54 (81 x 34 x 1)
206 x 86.4 x 2.54 (81 x 34 x 1)
213.4 x 38.1 x 2.54 (84 x 15 x 1)
40.3 x 19.8 (15.9 x 7.9)
Description
IBD designed exclusively for use with the EMF; features left-to-right fiber routing, internal slack storage and front-to-rear feed through
Contains the CCF-EC-7 end cap to create a single kit for ending a bay line-up with slack storage and end protection
Simple One-Piece Decorative Lift-Off Front Panel Cover for the front of the EMF
Dual-Door Lift-Off Front Cover Panels for the EMF, provides individual access to the left or right column of termination housings
Decorative End Cap for protecting the end of a bay line-up
Isolation Pad for EMF IBD (mounting hardware not required)
Part Number
CCF-IBD-T3
CCF-IBD-EC-7
CCF-COVER-7
CCF-COVER-2-7
CCF-EC-7
CCF-IBD-PAD-KIT
ordering information |
SPECIFICATION SHEET EVO-278-EN | PAGE 16
Enhanced Management Frame (EMF)
A Corning® Solutions Product
|
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
Transitional Inter-Bay Managers There is a series of transitional inter-bay managers designed to route fiber from the existing FiberManager™ System (FMS) line-ups into new enhanced management frame (EMF) line-ups when the two frame systems are placed side by side. Each transition bay option is distinguished by its relation to the EMF frame and the relative positions of the EMF and FMS frames to each other. Illustrations, application descriptions and part numbers are shown below.
Transitional Interbay Managers (IBU)
CCF-IBU-FMS-7-L CCF-IBU-FMS-7-R CCF-IBU-FMS-7-LF CCF-IBU-FMS-7-RFCCF-IBU-FMS-C
��-����
CCF-IBU-FMS-C and CCF-IBU-FMS-C-JT | Drawing ZA-2629
Transitional Interbay Managers (IBU)
CCF-IBU-FMS-7-L CCF-IBU-FMS-7-R CCF-IBU-FMS-7-LF CCF-IBU-FMS-7-RFCCF-IBU-FMS-C
��-����
CCF-IBU-FMS-7-L and CCF-IBU-FMS-7-R | Drawing ZA-2629
Transitional Interbay Managers (IBU)
CCF-IBU-FMS-7-L CCF-IBU-FMS-7-R CCF-IBU-FMS-7-LF CCF-IBU-FMS-7-RFCCF-IBU-FMS-C
��-����
CCF-IBU-FMS-7-LF and CCF-IBU-FMS-7-RF | Drawing ZA-2629
SPECIFICATION SHEET EVO-278-EN | PAGE 17
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 18
Enhanced Management Frame (EMF)
Dimensions(H x W x D) cm (in)
84 x 12 x 5 (213.4 x 30 x 12.7)
84 x 12 x 5 (213.4 x 30 x 12.7)
84 x 12 x 5 (213.4 x 30 x 12.7)
84 x 12 x 5 (213.4 x 30 x 12.7)
84 x 12 x 5 (213.4 x 30 x 12.7)
84 x 12 x 5 (213.4 x 30 x 12.7)
Description
IBU that feeds fiber from an FMS to an EMF positioned on the left; hardware order looking from the front and left to right is EMF-IBU-FMS; suitable only for EMF and FMS frames positioned with flush rear-most surfaces
IBU feeds fiber from an FMS to an EMF positioned on the right; hardware order looking from the front and left to right is FMS-IBU-EMF; suitable only for EMF and FMS frames positioned with flush rear-most surfaces.
IBU that feeds fiber from an FMS to an EMF positioned on the left; hardware order looking from the front and left to right is EMF-IBU-FMS; suitable only for EMF and FMS frames positioned with flush front-most surfaces
IBU feeds fiber from an FMS to an EMF positioned on the right; hardware order looking from the front and left to right is FMS-IBU-EMF; suitable only for EMF and FMS frames positioned with flush front-most surfaces
Center IBU for use with an FMS positioned directly between two EMF frames; two IBUs shipped per kit
Rear Troughs for use with the CCF-IBU-FMS; troughs span the rear of the FMS frame
Part Number
CCF-IBU-FMS-7-L
CCF-IBU-FMS-7-R
CCF-IBU-FMS-7-LF
CCF-IBU-FMS-7-RF
CCF-IBU-FMS-C
CCF-IBU-FMS-C-JT
ordering information |
A Corning® Solutions Product
Troughs Between Custom IBD and Standard IBD Units
ZA-3601
Right Rear Trough
#12-24 ThreadCuttingScrews
Center Rear Trough
Custom IBD
Standard IBD
Troughs Between Custom IBD and Standard IBD Units | Drawing ZA-3601
EMF to UDF Transition Corning Cable Systems EMF to UDF Integration System provides a unique solution that enables the mounting of traditional optical hardware and electron-ics right next to the modular EMF frame. Unlike any other solution in the industry, this system provides pre-engineered front to rear and lateral fiber management pathways between a modular style high-density frame and traditional 19- or 23-in frames without requiring costly overhead raceways.
specifications |
Trough to be Used on UDF Frame and IBD Unit Arrangement
Center Rear Trough UDF is between two custom IBD units Right Rear Trough UDF is to right of EMF when viewed from front and UDF has no IBD or has a standard IBD on its right side Left Rear Trough UDF is to left of EMF when viewed from front and UDF has no IBD or has a standard IBD on its left side
Description
Individual Jumper Trough, EMF-UDF, center, rear trough, platinum
Individual Jumper Trough, EMF-UDF, right, rear trough, platinum
Individual Jumper Trough, EMF-UDF, left, rear trough, platinum
IBU, transition, EMF-UDF, platinum
Part Number
Transition Equipment
CCF-JT-UDF-CR
CCF-JT-UDF-RR
CCF-JT-UDF-LR
CCF-IBD-UDF-7
ordering information |
|
PR
ETER
MIN
ATED
SYS
TEM
S
|
CAB
LES
|
C
ON
NEC
TOR
S
|
CAB
LE A
SSEM
BLIE
S
| H
ARD
WAR
E
|
CO
PPER
CO
NN
ECTI
VITY
|
S
PLIC
E AN
D T
EST
EQU
IPM
ENT
|
TR
AIN
ING
|Enhanced Management Frame (EMF)
SPECIFICATION SHEET EVO-278-EN | PAGE 19
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 20
Enhanced Management Frame (EMF)
2-ft extension
4.5-ft extension 7-ft UDF frame
ZA-1628
UDF Equipment Rack and Extensions | Drawing ZA-1628
Frame Components Equipment RacksThe backbone of each distribution bay is its equipment rack. Standard 58.4 cm (23 in) equipment racks are available in 2.1 m (7-ft) heights. 2.7 m (9-ft) and 3.5 m (11.5-ft) heights are achieved using 2-ft and 4.5-ftextensions. Rack styles feature industry-standard EIA hole spacing.
Description
7-ft Unequal Flange Equipment Rack, 23-in, platinum
7-ft Unequal Flange Equipment Rack, 19-in, platinum
2-ft Rack Extension for use with UDF rack (23-in), platinum
2-ft Rack Extension for use with UDF rack (19-in), platinum
4.5-ft Rack Extension for use with UDF rack (23-in), platinum
4.5-ft Rack Extension for use with UDF rack (19-in), platinum
Part Number
Equipment Racks
UDF-ERO-23E-07-000
UDF-ERO-19E-07-000
Extensions
UDF-EXT-23E-02-000
UDF-EXT-19E-02-000
UDF-EXT-23E-04-000
UDF-EXT-19E-04-000
ordering information |Dimensions(H x W x D) cm (in)
213.4 x 65.8 x 25.7 (84.0 x 25.9 x 10.1)
213.4 x 55.6 x 25.7 (84.0 x 21.9 x 10.1)
60.9 x 65.8 x 25.7 (24 x 25.9 x 10.1)
60.9 x 55.6 x 24.4 (24 x 21.9 x 9.6)
137 x 65.8 x 25.7 (54 x 25.9 x 10.1)
137 x 55.6 x 24.2 (54 x 21.9 x 9.6)
ShippingWeight kg (lb)
22.6 (50)
22.6 (50)
9.1 (20)
8.2 (18.1)
15 (33.1)
14 (31)
A Corning® Solutions ProductUDF-EC-7
ZA-1266
84"
12"
2.5"
84"
15"
2.5"
End Cap (UDF-ECO-07-000) | Drawing ZA-1266
Frame Components End CapsEnd caps provide protection for the end of each row of bays. End caps are not required between the racks in a given row (must be ordered separately).
Foot CapsFoot caps are a protective covering at the base of the rack that allow mounting of A/C outlets that are required in the frame system.
Inter-Bay Storage UnitsInter-bay storage units (IBUs) route and manage jumpers on the front of the UDF. The IBUs have nine routing hubs, a top jumper trough bridge and a bottom jumper trough.
Description
End Cap for 7-ft unequal flange rack (UDF)
2-ft End Cap Extension for unequal flange rack (UDF)
4.5-ft End Cap Extension for unequal flange rack (UDF)
Inter-Bay Storage Unit with jumper trough, UDF, single sided
Part Number
End Caps
UDF-ECO-07-000
UDF-EC-EXT-7/9
UDF-EC-EXT-7/11
Inter-Bay Storage Units
UDF-IBU-7-1
ordering information |Dimensions(H x W x D) cm (in)
212.4 x 7.6 x 30.5 (83.6 x 3.0 x 12.0)
60.9 x 7.6 x 30.5 (24.0 x 3.0 x 12.0)
137.0 x 7.6 x 30.5 (54.0 x 3.0 x 12.0)
213.1 x 12.1 x 15.2 (84.0 x 4.75 x 6.0)
ShippingWeight kg (lb)
15.9 (35.0)
4.5 (10.0)
10.2 (22.5)
9.1 (20.0)
FDF-IBU-7-1
ZA-1653
Inter-bay Storage Unit (UDF-IBU-7-1) | Drawing ZA-1653
SPECIFICATION SHEET EVO-278-EN | PAGE 21 |
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|Enhanced Management Frame (EMF)
A Corning® Solutions Product
Enhanced Management Frame (EMF)
ZA-1538
Top Jumper TroughECL-T2U-19
UDF Standard Upper Trough | Drawing ZA-1538
Frame Components Jumper Troughs and Jumper Trough BridgesJumper troughs organize and protect jumpers routed on the front of the frame and also allow jumper routing from one side of the rack to the other. Jumper troughs are also used for express routing of jumpers through the bay to adjacent bays and are available in a variety of sizes. Jumper trough bridges provide increased sup-port between bays.
Description
UDF Upper Trough for 23-in, platinum
UDF Upper Trough for 19-in, platinum
UDF Standard Trough for 23-in, platinum
UDF Standard Trough for 19-in, platinum
Part Number
Jumper Troughs and Jumper Trough Bridges
UDF-JT-23T
UDF-JT-19T
UDF-JT-23B
UDF-JT-19B
ordering information |Dimensions(H x W x D) cm (in)
10 x 65.5 x 12.7 (3.97 x 25.81 x 5.00)
10 x 55.4 x 12.7 (3.97 x 21.81 x 5.00)
10 x 65.5 x 12.7 (3.47 x 25.81 x 5.00)
10 x 55.4 x 12.7 (3.47 x 21.81 x 5.00)
ZA-2848
UDF Standard Upper Trough
UDF-IT-19T-35
UDF Standard Trough | Drawing ZA-2848
SPECIFICATION SHEET EVO-278-EN | PAGE 22
A Corning® Solutions Product
Enhanced Management Frame (EMF)
|
P
RET
ERM
INAT
ED S
YSTE
MS
|
C
ABLE
S
|
CO
NN
ECTO
RS
|
C
ABLE
ASS
EMBL
IES
|
HAR
DW
ARE
|
C
OPP
ER C
ON
NEC
TIVI
TY
|
SPL
ICE
AND
TES
T EQ
UIP
MEN
T
|
TRAI
NIN
G
|
installation information |For further details on how to install Corning Cable Systems Enhanced Management Frame (EMF) products, please refer to the following Corning Cable Systems recommended procedures:
Part Number
SRP-003-542
SRP-003-580
SRP-003-599
SRP-003-612
SRP-003-613
SRP-003-622
SRP-003-634
SRP-003-635
SRP-003-636
SRP-000-267
SRP-000-262
SRP-000-263
SRP-000-264
SRP-000-787
SRP-003-891
Description
Enhanced Management Frame (EMF) – Frame Installation
EMF Housing Installation Guide, Jumper Management and Mainenance
EMF Jumper Routing Procedures
EMF Accessories
IBU Bridging EMF and Fiber Manager Frame
CCF Frame Extensions for EMF
End Cap for EMF
End Guard for EMF
EMF Door Installation
Installation for Inter-Bay Storage Unit - EMF to UDF
EMF Trough Edge Guard Installation
EMF WATERFALL Installation
EMF Rear Trough Retainer Kit Installation
EMF CWDM/MUX & DEMUX Module Installation
EMF Housings with MTP® Connectors
SPECIFICATION SHEET EVO-278-EN | PAGE 23
A Corning® Solutions Product
SPECIFICATION SHEET EVO-278-EN | PAGE 24
Enhanced Management Frame (EMF)
notes |
Corning Cable Systems LLC • PO Box 489 • Hickory, NC 28603-0489 USA 800-743-2675 • FAX: 828-325-5060 • International: +1-828-901-5000 • www.corning.com/cablesystemsCorning Cable Systems reserves the right to improve, enhance and modify the features and specifications of Corning Cable Systems products without prior notification. ALTOS, FREEDM, MIC, Pretium EDGE, SearchLite and TBII are registered trademarks of Corning Cable System Brands, Inc. FiberManager, LSZH and SST-Ribbon are trademarks of Corning Cable Systems Brands, Inc. Corning is a registered trademark of Corning Incorporated. MTP is a registered trademark of USConec, Ltd. All other trademarks are the properties of their respective owners. Corning Cable Systems is ISO 9001 certified. © 2009, 2012 Corning Cable Systems. All rights reserved. Published in the USA.. EVO-278-EN / March 2012