1
MET ONE Leader in Airborne Particle Counting
Enhanced MET ONE 3400 SeriesEnhanced MET ONE 3400 Series Portable Airborne Particle Counters Portable Airborne Particle Counters
2
MET ONE Leader in Airborne Particle Counting
Introduction to MET ONE 3400 Series
• Flexible Communications– Wireless, Ethernet, Serial, USB
• OPC Server Enabled Open Communication Architecture
– Seamless integration into YOUR System Software
– LIMS
• Industry Standard for Ease of Use– Easy area, location, parameter configuration
• 21 CFR Part 11 Compliance– Secure multi-level log on
• Cleanroom Classification Wizard– A few clicks to compliance!
Solutions from simple, manual
printout operation to multiple data
integration options
3
MET ONE Leader in Airborne Particle Counting
Flexible Communications - Wireless
Optional Wireless 802.11 b/g based I/O for FMS connectivity
USB connectivity for data retrieval / communications
4
MET ONE Leader in Airborne Particle Counting
Traditional Printout / Spreadsheets
Paper-based procedures, data acquisition, data entry and reporting
Hach PortAll Version 2.4 Software
• Organize, archive and report particle count data– Intuitive, easy-to-use software
• Paperless, secure data transfer in a 21 CFR Part 11 environment– Supports Ethernet, wireless and serial communications– Supports encrypted file transfer via memory stick
• Easy Report Generation– Create ISO14644, Annex 1 and FS209E Cleanroom Reports– Export reports to locked PDF file format suitable for LIMS archival
6
MET ONE Leader in Airborne Particle Counting
MET ONE Compliance Workflow Software
• Direct Paperless data acquisition
• Can serve as data of record
• Count data may also be exported to LIMS (Ethernet, wireless)
7
MET ONE Leader in Airborne Particle Counting
MET ONE Compliance Workflow Software
Direct Paperless Data Acquisition
The MET ONE CWS acquisition software (powered by MODA) provides seamless integration with the MET ONE 3400 series airborne particle counters eliminating the need for paper tape output, savingvaluable operator time and reducing the risk of error.
21 CFR Part 11 Compliance
OPC Server – Particle Data integrated into your software
• Eliminates collection, validation and storage of paper tapes and manual data entry tasks.
• If daily reporting of portable data is the primary goal, Met One OPC Server is a “total solution.”
Data from portables
Met One OPC Server
Sensor Control & OPC Server
Database
Business networkCustomerDatabase
(LIMS, etc)
9
MET ONE Leader in Airborne Particle Counting
Integration into FMS Systems for Aseptic Production Monitoring
Client # 1 Fill Line A
Server/client with database
Fill Line A
Fill Line B
Grade C & D monitoring
Client # 2Fill Line B
Ethernet
RS-485
Ethernet or RS-485
10
MET ONE Leader in Airborne Particle Counting
Intuitive User Interface!
• Wizard to conduct pass/fail test for ISO, EU-GMP Annex I, FS 209E and BS5295 standards
• No expertise in standards required. Few clicks to compliance
• The wizard guides an operator step by step to sample data, process data and product reports
Test wizard for standards compliance
11
MET ONE Leader in Airborne Particle Counting
Intuitive User Interface!
• Group is a collection of desired sampling parameters
• New group can be created or existing group can be loaded
• A location can be added to or removed from a group
• ‘Settings’ button allows pre-selecting sampling parameters such as sampling time, delay, hold time, count and environmental alarm, etc.
Improved group management
12
MET ONE Leader in Airborne Particle Counting
Intuitive User Interface!
• Multiple level of user accounts – Basic (no log in)– Operator– Administrator
• No limits to number of log in accounts
• An administrator can create operator level user account and assign selective access rights and group access
21 CFR Part 11 compliance: unique user log in
13
MET ONE Leader in Airborne Particle Counting
Meets ISO 21501-4 Calibration Standard
Designed to fully comply with ISO 21501-4 calibration standard for data accuracy and consistency between counters
“The purpose of ISO 21501 is to provide a calibration procedure and verification method for particle counters, so as to minimize the inaccuracy in the measurement result by a counter, as well as the differences in the results measured by different instruments”
14
MET ONE Leader in Airborne Particle Counting
Air Particle Counter CalibrationISO 21501 and ISO 14644 - the link to GMP
• Regulators inspect to EU GMP, which calls up ISO14644
• Next revision ISO14644 will refer to ISO21501-4
• ISO 21501-4 states – “Instruments that conform to this part of ISO 21501 are used for the classification of air cleanliness in cleanrooms and associated controlled environments in accordance with ISO 14644-1”
15
MET ONE Leader in Airborne Particle Counting
ISO 21501 Calibration Standard
• Improved compliance– Removes ambiguity by providing a single internationally recognized
standard method for calibration– Harmonization between ISO and GMP guidance
• Improved unit-to-unit reproducibility– All particle counters are referenced to a “gold” standard
• Improved counting accuracy– Reduces false alarms in Grade A areas
All current Met One particle counters from Hach may be calibrated using ISO 21501 at your facility
For further information go to: www.iso21501.comOr email: [email protected]
16
MET ONE Leader in Airborne Particle Counting
Standard Shipment Includes
Item Number Description
1 3400 series particle counter
2 Rechargeable Battery (1 unit)
3 AC adapter
4 Power cord US
5 Power cord EU
6 Thermal printer paper (2 rolls)
7 Clamp, isokinetic probe holder
8 Tripod, isokinetic probe holder
9 Isokinetic probe
10 Extension tubing for isokinetic probe
11 Zero count filter
12 RS 485 connector assembly
13 USB drive (1 unit)
14 Intake cleaning brush
15 Wireless antenna for optional Wi-Fi Unit
16 Stylus for touch screen interface
17
MET ONE Leader in Airborne Particle Counting
Why MET ONE?
• Vendor Consolidation– Hach is Anatel, Orbisphere, HIAC, Met One
– Local Sales / Service for all Instruments
– (local service engineer in Durham, NC)
18
MET ONE Leader in Airborne Particle Counting
MET ONE will program your Air Particle Counters
19
MET ONE Leader in Airborne Particle Counting
MET ONE will set-up your Air Particle Counters
After programming your new fleet of particle counters – we will hand you your new set of keys to your site specific programming
20
MET ONE Leader in Airborne Particle Counting
Screen Shot - Area/Location Setup
21
MET ONE Leader in Airborne Particle Counting
Screen Shot – Sample Setup
22
MET ONE Leader in Airborne Particle Counting
Screen Shot – Alarm Settings
23
MET ONE Leader in Airborne Particle Counting
Screen Shot – Main Operation Screen
24
MET ONE Leader in Airborne Particle Counting
Screen Shot – Viewing Past Test Runs
25
MET ONE Leader in Airborne Particle Counting
Screen Shot – Print Center
26
MET ONE Leader in Airborne Particle Counting
Screen Shot – Export Data to Thumb Drive
27
MET ONE Leader in Airborne Particle Counting
Screen Shot – System Status Screen
28
MET ONE Leader in Airborne Particle Counting
Copy Programming from Unit-to-Unit
Just 15 seconds to replicate
29
MET ONE Leader in Airborne Particle Counting
New Enhanced MET ONE 3400
• Flexible Communications– Wireless, Ethernet, serial and USB
• Compliance Setup Wizard– A few clicks to compliance for
ISO14644, EU GMP Annex 1 and FS 209E
• Seamless connectivity to data management software
– OPC server enabled open communication architecture
• Intuitive user interface– Easy area, location, operating
parameter
• 21CFR Part 11 compliance– Secure multi-level logon, secure
data transfer
• Unit-to-unit accuracy and reproducibility
– Assured through ISO 21501 compliance
• Long continuous operation– Dual hot-swappable batteries
• Now available in 1 CFM, 50 LPM and 100 LPM flow rates
– Optimized for your application