PowerPoint Presentation

Some useful EnodeB MML commands.

:-Command: Ping :-Command: DSP EnodeB:-Command: DSP BRD:-Command: DSP CELL:-Command: DSP ETHPORT:-Command: DSP GPS:-Command: DSP IPRT:-Command: DSP LOCALIP:-Command: DSP RETDEVICEDATA:-Command: DSP RRU:-Command: DSP S1INTERFACE:-Command: DSP X2INTERFACE:-Command: DSP VSWR:-Command: DSP BRDMFRINFO:-Command: DSP BRDTEMP:-Command: DSP CPRIPORT:-Command: DSP DEVIP:-Command: DSP MME:-Command: DSP OMCH:-Command: DSP SCTPLNK:-Command: ADD OP:-Command: MOD OP:-Command: LST OP:-Command: CLB RET:-Command: LST SECTOR:-Command: DSP X2INTERFACE RST EnodeB LST VLANMAP

Some useful EnodeB MML commands.

:- Command: ping :-Command: DSP EnodeB:-Command: DSP BRD:-Command: DSP CELL:-Command: DSP ETHPORT:-Command: DSP GPS:-Command: DSP IPRT:-Command: DSP LOCALIP:-Command: DSP RETDEVICEDATA:-Command: DSP RRU:-Command: DSP S1INTERFACE:-Command: DSP X2INTERFACE:-Command: DSP VSWR:-Command: DSP BRDMFRINFO:-Command: DSP BRDTEMP:- Command: DSP CPRIPORT:-Command: DSP DEVIP:- Command: DSP MME:-Command: DSP OMCH:-Command: DSP SCTPLNK:-Command: ADD OP:-Command: MOD OP:-Command: LST OP:-Command: CLB RET:-Command: LST SECTOR:-Command: DSP X2INTERFACE

1Loss of visibility(Ping test from MME to EnodeB)

Command: pingpinging form MME to EnodeB here typeSubrack no=0Slot no=> R=13, D=11, J=11.Destination ip= Enodeb IP(Command for Enode B DSP Devip. Take first to check loss of visibility )Source IP=10.15.27.1 (RYH, slot no.13), 10.7.32.1 (DAM, slot no.11), 10.16.16.1 (Jed, slot no.11) VRF name =S1_MME Here only destination IP will change all information will be same.2

Dear LTE Team ,In case ping test required to check other vendor sites which are connected with our MME you will need to MME source IP , MME subrack No and MME slot No .Here you can find all information to save the time :VRF Name is constant ( S1_MME_VRF )LASILKI _ USN : (PS-MSDH01)PS-SPJH01 ( JED _ USN ) : slot no 11

PS-MSRH01 ( RYD _ USN ) :

RYD _ USN1 :

Ping test from EnodeB to MME

For pint test from site to mme.First get the site IP (DSP devip)Ping Cabinet no , subrack no , slot no (give)Sourse ip (Site iP)Destination ip 10.15.27.1 , 10.16.16.1(J) , 10.7.32.1 (D)1000 packetS1_MME

Ping test from mme to site

Ping0,13, destination id(take from the person who gave)

4

Command: DSP EnodeBResult: shows EnodeB ID and Electronic serial number

Each EnodeB having unique ID5

Command: DSP BRDResult: position of BBU boards.6

Command: DSP CELLResult: show cell status at Cell instance state.7

Command: DSP ETHPORTType slot no=7 and sub board type=BASE_BOARD Result: eNodeB traffic ,MAC address and IP address.8

Command: DSP GPSResult: Number of GPS traced and other information shown above.

Command: DSP GPSSNRResult : GPS signal noise ratio( shows interference)

9

Command: DSP IPRTType Slot No= 7;Result: configured IP address10

Command: DSP LOCALIPResult: Local IP and subnet mast of EnodeB11

Command: DSP RETDEVICEDATAResult: shows Antenna information

And also we more information about antennas from below commandsDSP RET DSP RETPORTDSP ANTENNAPORT 12

Command: DSP RRUResult: RRU configured slot13

Command: DSP S1INTERFACEResult: shows EnodeB to MME link information.14

Command: DSP X2INTERFACEResult: X2 interface ID( Neighbors EnodeBs)15

Command: DSP VSWRResult: VSWR values;If VSWR value more the 150 then need to open TT.16

Command: DSP BRDMFRINFOResult : Board information on given slot.17

Command: DSP BRDTEMPResult :Board Temperature.18

Command: DSP CPRIPORTResult: shows CPRI cables connection and current bit-rate as per the STC it should be 4.9G19

Command: DSP DEVIPEnodeB IP address

192.168.0.49 for local maintenance 20

Command: DSP MMEResult: shows MME IP address

As we know each enodeB is connected to 2 MME Type 0 and 1 for different MMEs;21

Command: DSP OMCHResult : operation metaintenace informationDestination IP is M2000 IP22

Command: DSP SCTPLNK

Here first peer ip address is MME ip and STCP port is MME logical port 23

Command: ADD OP

If need to add new user for BBU login then use above command and create new user by filling above info.

To modify user then we have

Command: MOD OPCommand: LST OP

LST OP shows total users24

Command: CLB RET

To calibrated antenna use CLB RET command.25

Command: LST SECTORResult: gives complete sector configuration information.

As per the STC sector must be configure as below

sector No Sub rack no 060 161 26026

To troubleshot X2interference fault alarm ,alarm comes whenever local cells locked, site down neighbor cell down or site down.

Location Information: X2INTERFACEID=16, CN Operator ID=0, Problem=X2 link setup failure, Description=NULL (alarm example)

Command: DSP X2INTERFACE-> give X2interface ID -> check X2 SCTP link ID then again run command DSP SCTPLNK and give SCTP Link ID as shown in next slide.27

First peer IP address is neighbor IP address of effected site28SET RRUCLKSRCDSP RRUCLKSRCTST LOPRRUSTR RRULNKTSTSTP RRULNKTSTTST LOPRRU29Ping

LST DEVIP; the IP addr in the second line is the traffic IP address;

Ping NB site or MME;

Check MME IP//chose USN LST DEVIP

30

Site down due to powerNPTS accepted//refer to E/CRBldg;NPTS not accept then refer to HUA-FO-SLTransmission issueFive types:MW,DWDM,Dark fiber,PAN,GPONMW/DWDMDS-TNOC-SFM(provide the NI,VLANs)GPONHuawei-FTTX-FO-NS(provide the Vlans and MDU,site IP)For Cisco ,provide PeAgg Name, Slot/Bay/Port,IP and Vlans

NE40 to RTPE uplink goes down need open TT and inform to BO

In case ping test required to check other vendor sites which are connected with our MME you will need toMME source IP , MME subrack No and MME slot No .Here you can find all information to save the time :VRF Name is constant ( S1_MME_VRF )LASILKI _ USN :

PS-SPJH01 ( JED _ USN ) :PS-MSRH01 ( RYD _ USN ) :RYD _ USN1 :

35