Date post: | 20-Mar-2017 |
Category: |
Documents |
Upload: | scott-adcock |
View: | 157 times |
Download: | 1 times |
Environmental / Signage Graphic Designer
SCOTTADCOCK
iOSHTML CSS PHPUI/UX JS
Fl Fw Pr Ae
Ai Ps Id Dw
CLIENT:
1
Role: Design and Engineering
Project consisted of the concept and creation of exterior signage for the Aspen office of the company. As the brand represents high-end, luxury properties, a look a feel that would convey this element was critical. The substrate the sign was ultimately mounted to featured rustic wood and the contrast of materials yielded an up scale presentation.
Programs Used:
CLIENT:
2 Ai Ps
36” /
914
mm
36” / 914mm
Raised cut stainless steel sections with clear coatattaches via 2” standoffs
22.8” x 24” / 579mm x 610mm
Notes:Stainless steel is .125” thick and has brushed finish with clear coat applied.Wall standoffs are welded to the back of the “house” peices and “Invited Home” letteringas to be determined
Live area = 3’ x 3’ (36” / 914mm x 36” / 914mm)
Raised cut stainless steel lettering with clear coatattaches via 2” standoffs
34.8” x 5” / 884mm x 127mm
Cut stainless steel lettering with clear coatattaches directly to exterior of building (27.5” x 3.5” / 699mm x 89mm)
CLIENT:
3
Role: Design and Engineering
Project consisted of the concept and creation of exterior signage for the Telluride, CO office of the company. As the brand represents high-end, luxury properties, a look a feel that would convey this element was critical. The sign needed to be double sided as it was going to hang from an existing structure near the exterior of the office building in historical old town Telluride.
Programs Used:
CLIENT:
4 Ai Ps
Center wood plank is stained to match
(Thickness TBD)
Metal hanging tabs insert intoslot cut in top of wood - held inplace by threaded insert
(Thickness TBD)
Metal spacers
Metal threaded insertfor binding metalpanels to wood center panel
Black oxide screws
Laser cut brushed stainless steel panels (with clear coat)are raised off of wood via .5” spacer standoffs andblack oxide bolts
(Panel measuers 32” x 22” / 813mm x 559mm)
NOTE: This sign is double sided
CLIENT:
5
Role: Design and Engineering
Project consisted of the concept and creation of exterior signage for the California Craft Brewer with a vintage look a feel. Choosing to use neon and chasing clear light bulbs produced the look the client was after and a design that hearkens back to classic roadside signs of the past. Using Illustrator / Photoshop to create isometric views for presentation and final files for product output as well as animation files for controlling the motion of the sign were employed.
Programs Used:
CLIENT:
6Ai Ps
49” /
124
5mm
Screen printedenamel surface
Clear Red Arrow elementsthat flash in sequence fromright to left
OrangeOption: TAP / ROOMcould flash in sequencewith arrows
Clear Red borderis illuminated at all times
White is illuminated at all times
Marquee type chaser bulbsthat sequence with the neonarrow elements
Enamel printed metal casewith mounting provitions aswell as hard wired electrical
82” / 2083mm
CLIENT:
7
Role: Design and Engineering
Project consisted of the concept and creation of signage to be used in point of purchase locations and be versatile in terms of orientation from a horizontal to vertical position. The LED illuminated project also featured a two sided approach and universal brackets allowing the sign to be configured for the final location. Using CAD tools within illustrator, the final dimensional drawings and DXF files were created for output.
Programs Used:
CLIENT:
8 Ai Ps
M10168-001
Index Part Number Qty. Description1. M 001 1 Top Assembly2. M 002 1 LED Module3. P 003 1 Diffuse Panel4. P 001 2 Screen Printed Face Panel5. P 002 2 Pub Bracket6. P 030 4 Binding Post / Threaded
2.
3.
1.
4.
4.
6.
6.
5.
P10168-002
(16 Gauge )HR Steel / Black �nish
Fold / 90˚
1.75” / 44mm
.375” / 9.5mm
1.25
” / 3
2mm
.25” / 6mm
B.A.
6mm / .25” Drilled hole(All locations)
Notes:Do Not Scale
B. A.
Notes:Do Not Scale
M10168-002
Wall pack power cordwith in line power switch5’ power cord length
LED light panel module(17.5” x 9.5” / 444mm x 241mm)
Clear acrylic material(.315” / 8mm minimum)
16.5” / 419mm
17.5” / 444mm
6.43
” / 1
63m
m
9.5”
/ 24
1mm
2.58
” / 6
5mm
.5” / 13mm
.5” / 13mm .5” / 13mm
Power inlet location on the sideof the LED module
Module illuminates viaWhite LED’s(Even illumination spacing)
6mm / .25” Drilled hole
M10168-002
Temporary tape locationsfor securing the LED array inthe router channel (Masking Tape)
CLIENT:
9
Role: Design and Engineering
Project consisted of the concept and creation of signage to be used in point of purchase locations focusing on the unique nature of the Myrcenary product. Original artwork to be printed on canvas material for a vintage appearance and installed inside a motorcycle tire for a dimensional presentation. Frosted acrylic was to also be used for the “smoke” elements and to frame the canvas printed artwork.
Programs Used: Ai Ps
Simple. Clean. To Use.
Fbzdgnzfghmxgh,cjmn
.wr lRV .RV/RW L;W
WENFI wefwEF.
ergbaerbj aodfb ldb qeb
etb qtb qtb qt egqv w
w je yje yje g wec we.
qwrgqerhg wt h wth wth
tgqerg qevg nyje nwrtbn
qwerfqwrgtrn qerg .
Fbzdgnzfghmxgh,cjmn
.wr lRV .RV/RW L;W
WENFI wefwEF.
ergbaerbj aodfb ldb qeb
etb qtb qtb qt egqv w
w je yje yje g wec we.
qwrgqerhg wt h wth wth
tgqerg qevg nyje nwrtbn
qwerfqwrgtrn qerg.
seba wryn yrj q4t
wgwrthnwyj wrythwrty
wth wthwthwtrhukr.
CLIENT:
10
Role: Design and Engineering
Project consisted of the concept and creation of a retail display unit that would not only educate the consumer about the product, but also convey the comapny’s strong support of eco-friendly manufacturing nature. The display featured the use of reclaimed wood materials and recycled aluminum. Unique cylindrical shape was chosen for functionality within the retail environment as well as an aesthetic nature mimicking the container concept of the product itself.
Programs Used: Ai Ps
CLIENT:
11
Role: Design and Engineering
Project consisted of the concept and creation of point of purchase signage that would allow some customization at retail depending on the products offered at each location. An additional LED array was added to the bottom of the horizontal sign for illuminating the various on tap products. Used Illustrator and Photoshop to render for presentation and finally for production output files as required. Many other projects were also designed for the Bend, OR brewer.
Programs Used:
CLIENT:
12Ai Ps
CLIENT:
13
Role: Design and Engineering
Project consisted of the concept and creation of various way finding signage used throughout the different breweries (Long Trail, The Shed and Otter Creek Brewing Co.) using reclaimed materials as well as Beetle Kill Pine, steel, Aluminum and other texture rich substrates. Paint used for the US Forestry Service was used to highlight laser etched text and iconography.
Programs Used:
CLIENT:
14 Ai Ps
Role: Design and Engineering
In addition to way finding signage within the brewing complex, many point of purchase projects were also completed featuring various materials such as reclaimed wood, steel, canvas and other texture rich substrates to convey the proper look a feel for the company's various breweries as well as products.
Programs Used:
CLIENT:
15 Ai Ps
Environmental / Signage Graphic DesignerScott Adcock13033 Birch Dr.Thornton, CO 80241
[email protected]/adcockscott
scottadcockdesign.com
https://www.behance.net/Scott_Adcock
SCOTTADCOCK
iOSHTML CSS PHPUI/UX JS
Fl Fw Pr Ae
Ai Ps Id Dw