®
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-1
ENVISION INDIRECT8” X 3” Rounded
AVAILABLE FIXTURES
SPECIFICATIONSPendant Mount – Modular
SPECIFICATIONS
ORDERING LOGIC
ENM1
123
32 FT
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Quantity
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype**
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow FuseDU- Dust Cover
Options
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
E N M 1 -1
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed reflectors combine hammertone specular aluminum andbaked white enamel (nominal reflectance 86%).
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-5 for details or consult factory.
8"
3"
Qty Fixture section4 ENM1 1 32 40FT R12 120 GEB 2SE EL SCT F1/24 C005
1 ENM1 3 32 12FT R8 277 GEB DCT F2/15 C041
EXAMPLE:
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 1 - 2
8"
3"
E N M 1 - 3
8"
3"
*Also available in custom lengths; see D-9 for further information, or consult factory.
** Maximum # of emergency sections per run should not exceed number of fixture sections,
minus one. For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
®
E-2
ENVISION INDIRECT8” X 3” Rounded
1-LAMP
PHOTOMETRICSPendant Mount – Modular
2-LAMP
3-LAMP
90˚-120˚ 34%
90˚-130˚ 52%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 85%
90˚-120˚ 31%
90˚-130˚ 50%
90˚-150˚ 81%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 83%
90˚-120˚ 26%
90˚-130˚ 44%
90˚-150˚ 78%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 80%
1-LAMP
PERFORMANCE SUMMARIES
% Luminaire Lumens from
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-17
ENVISION INDIRECT/OPEN8” X 3” Rounded
®
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - WITH HOLES
SPECIFICATIONS - WITH HOLES
ORDERING LOGIC - WITH HOLES
ENM2
123
32 FTHOL
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Shielding Optio
ns
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow Fuse
Options
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
E N M 2 -1
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed reflectors combine hammertone specular aluminum andbaked white enamel (nominal reflectance 90%).
S H I E L D I N GDie-punched pattern in aluminum housing.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-25 for details or consultfactory.
8"
3"
Qty Fixture section4 ENM2 1 32 HOL 40FT R12 120 GEB10 2SE EL SCT F1/24 C005
1 ENM2 3 32 HOL 12FT R4 277 GEB DCT F2/15 C041 ACG
EXAMPLE:
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 2 - 2
8"
E N M 2 - 3
8"
3"3"
*Also available in custom lengths; see E-25 for further information, or consult factory.
** Maximum # of emergency sections per run equals number of fixture sections, minus one.
For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-18
ENVISION INDIRECT/OPEN8” X 3” Rounded
®
1-LAMP - WITH HOLES
PHOTOMETRICSPendant Mount – Modular
2-LAMP - WITH HOLES
3-LAMP - WITH HOLES
90˚-120˚ 35%
90˚-130˚ 52%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 87%
90˚-120˚ 32%
90˚-130˚ 50%
90˚-150˚ 80%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 84%
90˚-120˚ 26%
90˚-130˚ 44%
90˚-150˚ 77%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 81%
1-LAMP
PERFORMANCE SUMMARIES
% Luminaire Lumens from
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
®
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-19
ENVISION INDIRECT/OPEN8” X 3” Rounded
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - WITH SLOTS
SPECIFICATIONS - WITH SLOTS
ORDERING LOGIC - WITH SLOTS
ENM2
123
32 FTSLT
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Shielding Optio
ns
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un) (optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow FuseDU- Dust CoverRIF- Radio Interference Filter
Options
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
E N M 2 -1
8"
Qty Fixture section4 ENM2 2 32 SLT 40FT R12 120 GEB10 2SE EL SCT F1/24 C005
1 ENM2 3 32 SLT 12FT R4 277 GEB DCT F2/15 C041 ACG
EXAMPLE:
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 2 - 2
8"
E N M 2 - 3
8"
3" 3" 3"
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed reflectors combine hammertone specular aluminum andbaked white enamel (nominal reflectance 90%).
S H I E L D I N GDie-punched pattern in aluminum housing.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-25 for details or consultfactory.
*Also available in custom lengths; see E-25 for further information, or consult factory.
** Maximum # of emergency sections per run equals number of fixture sections, minus one.
For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
®
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-20
ENVISION INDIRECT/OPEN8” X 3” Rounded
1-LAMP - WITH SLOTS
PHOTOMETRICSPendant Mount – Modular
2-LAMP - WITH SLOTS
3-LAMP - WITH SLOTS
90˚-120˚ 35%
90˚-130˚ 52%
90˚-150˚ 82%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 87%
90˚-120˚ 32%
90˚-130˚ 50%
90˚-150˚ 80%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 84%
90˚-120˚ 26%
90˚-130˚ 44%
90˚-150˚ 77%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 81%
1-LAMP
PERFORMANCE SUMMARIES
% Luminaire Lumens from
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-21
ENVISION INDIRECT/OPEN8” X 3” Rounded
®
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - WITH WINDOWS
SPECIFICATIONS - WITH WINDOWS
ORDERING LOGIC - WITH WINDOWS
ENM2
123
32 FTWIN
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Shielding Optio
ns
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow FuseDU- Dust CoverRIF- Radio Interference Filter
Options
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
E N M 2 -1
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed reflectors combine hammertone specular aluminum andbaked white enamel (nominal reflectance 90%).
S H I E L D I N GWindow with clear acrylic optical lens.Satin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-25 for details or consult factory.
8"
Qty Fixture section4 ENM2 1 32 WIN 40FT R12 120 GEB10 2SE EL SCT F1/24 C005
1 ENM2 3 32 WIN 12FT R4 277 GEB DCT F2/15 C041 ACG
EXAMPLE:
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 2 - 2
8"
E N M 2 - 3
8"
3" 3" 3"
*Also available in custom lengths; see E-25 for further information, or consult factory.
** Maximum # of emergency sections per run equals number of fixture sections, minus one.
For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-22
ENVISION INDIRECT/OPEN8” X 3” Rounded
®
1-LAMP - WITH WINDOWS
PHOTOMETRICSPendant Mount – Modular
2-LAMP - WITH WINDOWS
3-LAMP - WITH WINDOWS
90˚-120˚ 35%
90˚-130˚ 52%
90˚-150˚ 82%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 86%
90˚-120˚ 32%
90˚-130˚ 50%
90˚-150˚ 80%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 82%
90˚-120˚ 26%
90˚-130˚ 44%
90˚-150˚ 78%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 80%
1-LAMP
PERFORMANCE SUMMARIES
% Luminaire Lumens from
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
™
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks and “Lightvent” is a trademark of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-27
ENVISION LIGHTVENT8” X 3” Rounded
®
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - WITH HOLES
SPECIFICATIONS - WITH HOLES
ORDERING LOGIC - WITH HOLES
ENM3
23
32 HOL FT
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Shielding Optio
ns
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow FuseDU- Dust CoverRIF- Radio Interference Filter
Options
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
E N M 3 - 2
8"
3"
Qty Fixture section4 ENM3 2 32 HOL 40FT R12 120 GEB10 2SE EL SCT F1/24 C005
1 ENM3 3 32 HOL 12FT R4 277 GEB DCT F2/15 C041 ACG
EXAMPLE:
*Also available in custom lengths; see E-37 for further information, or consult factory.
** Maximum # of emergency sections per run should not exceed number of fixture sections, minus
one. For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 3 - 3
8"
3"
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed, white reflector with a minimum 90% reflectance.
S H I E L D I N GDie-punched pattern in aluminum housing.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-37 for details or consult factory.
™
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks and “Lightvent” is a trademark of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-28
ENVISION LIGHTVENT8” X 3” Rounded
®
2-LAMP - WITH HOLES
PHOTOMETRICSPendant Mount – Modular
3-LAMP - WITH HOLES
90˚-120˚ 28%
90˚-130˚ 43%
90˚-150˚ 70%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 81%
90˚-120˚ 23%
90˚-130˚ 40%
90˚-150˚ 71%
Maximum Flux Location 130˚-140˚
Luminaire Efficiency 81%
PERFORMANCE SUMMARIES
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
™®
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks and “Lightvent” is a trademark of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-29
ENVISION LIGHTVENT8” X 3” Rounded
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - WITH SLOTS
SPECIFICATIONS - WITH SLOTS
ORDERING LOGIC - WITH SLOTS
ENM3
23
32 SLT FT
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Shielding Optio
ns
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow FuseDU- Dust CoverRIF- Radio Interference Filter
Options
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed, white reflector with a minimum 90% reflectance.
S H I E L D I N GDie-punched pattern in aluminum housing.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-37 for details or consult factory.
Qty Fixture section4 ENM3 2 32 SLT 40FT R12 120 GEB10 2SE EL SCT F1/24 C005
1 ENM3 3 32 SLT 12FT R4 277 GEB DCT F2/15 C041 ACG
EXAMPLE:
*Also available in custom lengths; see E-37 for further information, or consult factory.
** Maximum # of emergency sections per run should not exceed number of fixture sections, minus one.
For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 3 - 2
8"
E N M 3 - 3
8"
3" 3"
™®
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks and “Lightvent” is a trademark of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-30
ENVISION LIGHTVENT8” X 3” Rounded
2-LAMP - WITH SLOTS
PHOTOMETRICSPendant Mount – Modular
3-LAMP - WITH SLOTS
90˚-120˚ 27%
90˚-130˚ 43%
90˚-150˚ 70%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 80%
90˚-120˚ 23%
90˚-130˚ 40%
90˚-150˚ 71%
Maximum Intensity Location 130˚-140˚
Luminaire Efficiency 80%
PERFORMANCE SUMMARIES
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
™
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks and “Lightvent” is a trademark of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-31
ENVISION LIGHTVENT8” X 3” Rounded
®
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - WITH WINDOWS
SPECIFICATIONS - WITH WINDOWS
ORDERING LOGIC - WITH WINDOWS
ENM3
23
32 WIN FT
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Shielding Optio
ns
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic BallastGEB10- 10% THD Ballast
(consult factory)
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Mounting Type
Feed/Suspension Length
Finish
ACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow FuseDU- Dust CoverRIF- Radio Interference Filter
Options
/
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming a 8" x 3" roundedchannel. Die-cast end plate attaches with no exposed fasteners.
R E F L E C T O R SDie-formed, white reflector with a minimum 90% reflectance.
S H I E L D I N GWindow with perforated metal overlay.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsand are UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4’, 8’, and 12’ lengths in a single section for exact suspension spacing of 4’, 8’, and 12’. For total fixture length add 1/2” for each end-cap.Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer-length fixtures.
Note: Custom lengths available; see page E-37 for details or consult factory.
Qty Fixture section4 ENM3 2 32 WIN 40FT R12 120 GEB10 2SE EL SCT F1/24 C005
1 ENM3 3 32 WIN 12FT R4 277 GEB DCT F2/15 C041 ACG
EXAMPLE:
*Also available in custom lengths; see E-37 for further information, or consult factory.
** Maximum # of emergency sections per run should not exceed number of fixture sections, minus
one. For additional sections, consult factory.
***EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
E N M 3 - 2
8"
3"
E N M 3 - 3
8"
3"
™
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks and “Lightvent” is a trademark of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-32
ENVISION LIGHTVENT8” X 3” Rounded
®
2-LAMP - WITH WINDOWS
PHOTOMETRICSPendant Mount – Modular
3-LAMP - WITH WINDOWS
90˚-120˚ 25%
90˚-130˚ 38%
90˚-150˚ 63%
Maximum Intensity Location 120˚-130˚
Luminaire Efficiency 82%
90˚-120˚ 22%
90˚-130˚ 36%
90˚-150˚ 65%
Maximum Intensity Location 130˚-140˚
Luminaire Efficiency 82%
PERFORMANCE SUMMARIES
2-LAMP
% Luminaire Lumens from
3-LAMP
% Luminaire Lumens from
®
E-39
ENVISION INDIRECT/DIRECT8” X 3” Rounded
AVAILABLE FIXTURES - T5 HIGH-OUTPUT
SPECIFICATIONSPendant Mount – Modular
SPECIFICATIONS - T5 HIGH-OUTPUT
ORDERING LOGIC - T5 HIGH-OUTPUT
ENM4 FT
12
54T5HO
R4- 4' sectionR8- 8' sectionR12- 12'section
120277
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
L/LP- No lampLP830- 3000K lampsLP835- 3500K lampsLP841- 4100K lamps
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color (consult factory)
Quantity
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)*
Emergency Type (o
ptional)*
*
Switching
Lamp Color
Mounting Type
Feed/Suspension Length
Finish
SSB- Semi-Specular BaffleACG- Adjustable Cable GrippersGLR- Fast Blow FuseGMF- Slow Blow Fuse
Options
GEB10- 10% THD Ballast(consult factory)
/
E N M 4 -1 E N M 4 - 2
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming an 8" x 29/16"rounded channel. Die-cast end plate mechanically attached with noexposed fasteners.
R E F L E C T O R SDie-formed specular aluminum.
S H I E L D I N GParabolic aluminum baffles with Achroma™ finish standard; semi-specular finish available. Includes VisorOptic™ opal diffuser lamp shield.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt or 277 volt. Pre-wired with prescribed circuits as specified.UL listed. Listed and labeled to comply with Canadian standards. Forspecial circuiting, consult factory. T5 high-output lamps are included.
F I X T U R E L E N G T H4'-0-1/4”, 8' and 12' lengths in a single section for exact suspensionspacing of 4', 8' and 12'. For total fixture length add 1/2” for each end-cap.
Qty Fixture section1 ENM4 2 54T5HO 40FT R12 120 GEB10 2SE EL SCT LP835 F1/24 C005 SSB
4 ENM4 1 54T5HO 12FT R8 277 GEB10 DCT L/LP F2/15 C100
EXAMPLE:
* Maximum # of emergency sections per run equals number of fixture sections, minus one. For
additional sections, consult factory.
**EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
8"
2 9/16"
8"
2 9/16"
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-40
8” X 3” Rounded
1-LAMP T5 HIGH-OUTPUT
PHOTOMETRICSPendant Mount – Modular
2-LAMP T5 HIGH-OUTPUT
PERFORMANCE SUMMARIES
ENVISION INDIRECT/DIRECT®
0˚-90˚ 16%
90˚-130˚ 41%
90˚-180˚ 84%
Maximum Direct Flux Location 30˚-40˚
Maximum Indirect Flux Location 120˚-130˚
Luminaire Efficiency 90%
2-LAMP
% Luminaire Lumens from
0˚-90˚ 21%
90˚-130˚ 44%
90˚-180˚ 79%
Maximum Direct Flux Location 30˚-40˚
Maximum Indirect Flux Location 110˚-120˚
Luminaire Efficiency 90%
1-LAMP
% Luminaire Lumens from
®
E-41
ENVISION INDIRECT/DIRECT8” X 3” Rounded
SPECIFICATIONSPendant Mount – Modular
AVAILABLE FIXTURES - T8
SPECIFICATIONS - T8
ORDERING LOGIC - T8
ENM4
123
32 FT
R4- 4' sectionR8- 8' sectionR12- 12'section
120277347
1SE- 1 section2SE- 2 sectionsXSE- X sections
EL- Emergency Battery PackEC- Emergency Circuit
SCT- Single CircuitDCT- Dual Circuit
Quantity
Fixture
# of Lamps in
Cross Section
Lamp Type
Nominal Row Length
(Must b
e in 4' in
crements)*
Maximum Secti
on Length
Voltage
Ballast T
ype
# of Emergency
Sections
(sections per r
un)(optio
nal)**
Emergency Type (o
ptional)*
**
Switching
GEB- Generic Electronic Ballast(consult factory)
F1- T-bar CeilingF2- Hard Ceiling Horizontal J-box
12- 12" overall suspension15- 15" overall suspension18- 18" overall suspension21- 21" overall suspension24- 24" overall suspensionXX- XX" overall suspension
C100- Satin Anodized FinishC200- Peerless Standard White (Low Gloss) C005- Soft White (Low Gloss)C032- White White (Gloss)C041- White White (Low Gloss)CXXX- Custom Color*
Mounting Type
Feed/Suspension Length
Finish
GLR- Fast Blow FuseGMF- Slow Blow FuseSSB- Semi-specular BaffleACG- Adjustable Cable Gripper
Options
/
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum forming an 8" x 29/16"rounded channel. Die-cast end plate mechanically attached with noexposed fasteners.
R E F L E C T O R SDie-formed specular aluminum.
S H I E L D I N GParabolic aluminum baffles with Achroma™ finish standard; semi-specular finish available.
F I N I S HSatin anodized or white paint standard; custom colors available.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsas specified. UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
F I X T U R E L E N G T H4'-0-1/4”, 8' and 12' lengths in a single section for exact suspensionspacing of 4', 8' and 12'. For total fixture length add 1/2” for each end-cap.
Qty Fixture section4 ENM4 2 32 40FT R12 120 GEB 2SE EL SCT F1/24 C005 SSB
1 ENM4 1 32 12FT R12 277 GDIM 1SE EC SCT F2/15 C100
EXAMPLE:
* Maximum # of emergency sections per run should not exceed number of fixture sections
minus one. For additional sections, consult factory.
**EC and EL not available concurrently. EL and EC not available with DCT in 4’ sections.Separate feed required.
Use guide below to order complete fixture runs from four feet to three-hundred feet in increments of four.
8"
2 9/16"
8"
2 9/16"
8"
2 9/16"
E N M 4 -1 E N M 4 - 2 E N M 4 - 3
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
®
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-42
ENVISION INDIRECT/DIRECT8” X 3” Rounded
PHOTOMETRICSPendant Mount – Modular
1-LAMP T8 2-LAMP T8
PERFORMANCE SUMMARIES3-LAMP T8
0˚-90˚ 38%
90˚-130˚ 30%
90˚-180˚ 62%
Maximum Direct Flux Location 30˚-40˚
Maximum Indirect Flux Location 120˚-130˚
Luminaire Efficiency 85%
2-LAMP
% Luminaire Lumens from
0˚-90˚ 36%
90˚-130˚ 35%
90˚-180˚ 64%
Maximum Direct Flux Location 30˚-40˚
Maximum Indirect Flux Location 110˚-120˚
Luminaire Efficiency 87%
1-LAMP
% Luminaire Lumens from
0˚-90˚ 34%
90˚-130˚ 28%
90˚-180˚ 66%
Maximum Direct Flux Location 30˚-40˚
Maximum Indirect Flux Location 130˚-140˚
Luminaire Efficiency 84%
3-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-11
ENVISION® INDIRECT9” X 3” Rounded
SPECS/PHOTOMETRICS1-Lamp T8
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum up to 24' in one uninterruptedsection forming a 9"x 3" rounded channel. Die-cast end plate mechanicallyattached with no exposed fasteners.
R E F L E C T O R SDie-formed reflectors combine hammertone specular aluminum (asrequired) and baked white enamel (nominal reflectance 86%). Opticalsystem includes micro-prismatic, 100% virgin acrylic specular/diffusingoptical lens.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuits asspecified. UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFactory options by specification. Length (to 24' in one piece - longer withinternal joiners), any finish (colors painted as selected).
CATALOG NO. EN1-010005
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 31%
90˚-130˚ 50%
90˚-150˚ 81%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 62%
1-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-12
ENVISION® INDIRECT9” X 3” Rounded
SPECS/PHOTOMETRICS1-Lamp Compact Fluorescent
C O N ST R U C T I O NHousing AA 6063 T6 extruded aluminum up to 24' in one uninterruptedsection forming a 9"x 3" rounded channel. Die-cast end plate mechanicallyattached with no exposed fasteners.
R E F L E C T O R SDie-formed reflectors combine hammertone specular aluminum (asrequired) and baked white enamel (86% nominal reflectance). Opticalsystem included micro-prismatic, 100% virgin acrylic specular/diffusingoptical lens.
E L E C T R I C A LSpecify 120 volt or 277 volt. Pre-wired with prescribed circuits as specified.UL listed. Listed and labeled to comply with Canadian standards. Forspecial circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFactory options by specification. Length (to 24' in one piece - longer withinternal joiners), any finish (colors painted as selected).
CATALOG NO. EN1-010007
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 32%
90˚-130˚ 51%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 62%
1-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-51
ENVISION®COVE7 1/4” X 33/4” Rectangular
SPECS/PHOTOMETRICS1-Lamp T8
C O N ST R U C T I O NHousing one-piece cold rolled sheet steel with die-formed end plateforming a 71/4"x 33/4" rectangular channel.
R E F L E C T O R SReflectors combine hammertone specular aluminum and baked whiteenamel (nominal reflectance 86%). Optical system includes micro-pris-matic, 100% virgin acrylic specular/diffusing optical lens.
F I N I S HBaked white enamel.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsas specified. UL listed. Listed and labeled to comply with Canadian stan-dards. For special circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFrom 2' to 8' in a single section. Lengths in 1' increments standard. Fornon-standard length fixtures, consult factory. Fixtures can be placedend-to-end to accommodate a cove of any length.
CATALOG NO. ECX-010000
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 33%
90˚-130˚ 51%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 70%
1-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-52
ENVISION®COVE83/4” X 23/4” Rectangular
SPECS/PHOTOMETRICS1-Lamp T8
C O N ST R U C T I O NHousing one-piece cold rolled sheet steel with die-formed end plateforming a 83/4"x 23/4" rectangular channel.
R E F L E C T O R SReflectors combine hammertone specular aluminum and baked whiteenamel (nominal reflectance 86%). Optical system includes micro-pris-matic, 100% virgin acrylic specular/-diffusing optical lens.
F I N I S HBaked white enamel.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsas specified. UL listed. Listed and labeled to comply with Canadianstandards. For special circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFrom 2' to 8' in a single section. Lengths in 1' increments standard. Fornon-standard length fixtures, consult factory. Fixtures can be placedend-to-end to accommodate a cove of any length.
CATALOG NO. ECX-010001
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 33%
90˚-130˚ 51%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 70%
1-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-53
ENVISION®COVE7 1/4” X 33/4” Rectangular
SPECS/PHOTOMETRICS2-Lamp T8
C O N ST R U C T I O NHousing one-piece cold rolled sheet steel with die-formed end plateforming a 71/4"x 33/4" rectangular channel.
R E F L E C T O R SReflectors combine hammertone specular aluminum and baked whiteenamel (nominal reflectance 86%). Optical system includes micro-pris-matic, 100% virgin acrylic specular/-diffusing optical lens.
F I N I S HBaked white enamel.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt.. Pre-wired with prescribedcircuits as specified. UL listed. Listed and labeled to comply withCanadian standards. For special circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFrom 2' to 8' in a single section. Lengths in 1' increments standard. Fornon-standard length fixtures, consult factory. Fixtures can be placedend-to-end to accommodate a cove of any length.
CATALOG NO. ECX-020002
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 35%
90˚-130˚ 53%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 55%
2-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-54
ENVISION®COVE83/4” X 23/4” Rectangular
SPECS/PHOTOMETRICS2-Lamp T8
C O N ST R U C T I O NHousing one-piece cold rolled sheet steel with die-formed end plateforming a 83/4"x 23/4" rectangular channel.
R E F L E C T O R SReflectors combine hammertone specular aluminum and baked whiteenamel (nominal reflectance 86%). Optical system includes micro-pris-matic, 100% virgin acrylic specular/-diffusing optical lens.
F I N I S HBaked white enamel.
E L E C T R I C A LSpecify 120 volt, 277 volt or 347 volt. Pre-wired with prescribed circuitsas specified. UL listed. Listed and labeled to comply with Canadianstandards. For special circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFrom 2' to 8' in a single section. Lengths in 1' increments standard. Fornon-standard length fixtures, consult factory. Fixtures can be placedend-to-end to accommodate a cove of any length.
CATALOG NO. ECX-020003
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 35%
90˚-130˚ 53%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 55%
2-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-55
ENVISION®COVE7 1/4” X 33/4” Rectangular
SPECS/PHOTOMETRICS1-Lamp Compact Fluorescent
C O N ST R U C T I O NHousing one-piece cold rolled sheet steel with die-formed end plateforming a 71/4"x 33/4" rectangular channel.
R E F L E C T O R SReflectors combine hammertone specular aluminum and baked whiteenamel (nominal reflectance 86%). Optical system includes micro-pris-matic, 100% virgin acrylic specular/-diffusing optical lens.
F I N I S HBaked white enamel.
E L E C T R I C A LSpecify 120 volt or 277 volt. Pre-wired with prescribed circuits asspecified. UL listed. Listed and labeled to comply with Canadian standards. For special circuiting, consult factory.
CATALOG NO. ECX-010004
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
90˚-120˚ 25%
90˚-130˚ 53%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 69%
2-LAMP
% Luminaire Lumens from
Peerless Lighting Box 2556, Berkeley, CA 94702-0556 510.845-2760 Fax 510.845-2776 www.peerless-lighting.com© 2000 . All rights reserved. “Peerless” and “Envision” are registered trademarks of . These products may be covered by one or more U.S. Patents or Patents Pending. 1/00
E-56
ENVISION®COVE83/4” X 23/4” Rectangular
C O N ST R U C T I O NHousing one-piece cold rolled sheet steel with die-formed end plateforming a 83/4"x 23/4" rectangular channel.
R E F L E C T O R SReflectors combine hammertone specular aluminum and baked whiteenamel (nominal reflectance 86%). Optical system includes micro-pris-matic, 100% virgin acrylic specular/-diffusing optical lens.
F I N I S HBaked white enamel.
E L E C T R I C A LSpecify 120 volt or 277 volt. Pre-wired with prescribed circuits as speci-fied. UL listed. Listed and labeled to comply with Canadian standards.For special circuiting, consult factory.
FAC T O RY M O D I F I C AT I O N SFrom 2' to 8' in a single section. Compact fluorescent lamps available onlywith 2', 4', 6' and 8' fixtures. For non-standard length fixtures, consultfactory. Fixtures can be placed end-to-end to accommodate a cove of anylength.
CATALOG NO. ECX-010005
PERFORMANCE SUMMARIESPHOTOMETRIC REPORT
SPECIFICATIONS
SPECS/PHOTOMETRICS1-Lamp Compact Fluorescent
90˚-120˚ 25%
90˚-130˚ 53%
90˚-150˚ 82%
Maximum Flux Location 120˚-130˚
Luminaire Efficiency 69%
2-LAMP
% Luminaire Lumens from