EP-55 Preview

Outer lock

Inner lock

EP-55 Installation

Step1

Step2

Adjust the dead bolt

Adjust the latch

bolt by pushing

hole.

Lift pin and pull the

body to the right.

2-3/ 8”

2-3/ 4”

60mm

70mm

2-3/ 8”

2-3/ 4”

Step3

Install latch bolt and dead bolt, making certain both latch

bolt and dead bolt hub are center to center.

Step4

Storeroom Function allows the latch to be locked at all times. Every time you

close the door the lock will lock automatically. To throw the deadbolt on storeroom

function, use the remote control and then lift the lever handle.

Passage/Entrance Function unlike the storeroom function, the door will

remain unlocked after each opening.

Make certain dead bolt is at retracted position.

Insert the spindle from

the outside of door to

the spring latch hole.

Step5

Set the handing cam to the

correct position.

(To match your door

swing R or L)

Handing Cam

R

Step6

Thread wire harness

below dead bolt

chaise (bypass the

posts).

Step7

Place the outer lock

body to engage with

the spindle in

alignment (the cam

clutch smoothly

engages with the

spindle, align both

inside and outside

housings to ensure

proper installation.

Step8

Sandwich plate

Install interior mechanism

(sandwich plate)

Step9

Tailpiece

Right door swing

Left door swing

Direction of tailpiece, vertical (RIGHT

HAND), horizontal (LEFT HAND),

for door swing

Step10

Engage interior mechanism

through Spindle hub hole.

Step11

Tailpiece

X

Engage tailpiece through

dead bolt hub.

Correct position for the wire

harness

Wrong position for the wire

harness (that will stop the

movement of tailpiece)

Step12

Make certain sandwich plate screws are

tight (this will prevent shifting of both

outside and inside plates)

Flat head screws

Round head screws (longer

than other 4 round head

screws)

Step13

Connect with wire harness.

In assembly, make certain wire harness is

located under the inside housing.

Lever Handle Shaft Coil Spring

Engage spindle onto

coil spring, and hub of

inside mechanism.

Step14

Tighten with 4

Round head screws

(Shorter than other

2 round head

screws)

Step15

Step16

Attach inside

escutcheon

Step17

Attach nylon washer and

lever handle on inside

and outside escutcheon.

Step18

Tighten the

lever handle

screw with

Allen wrench.

Step19

●●●● Final Operation Test

■■■■ Lift Lever Handle from inside and outside to lock Dead Bolt.

Confirm door cannot be opened from outside.

■■■■ WHEN LOCKING DOOR LIFT LEVER HANDLE ALL THE

WAY UP. If Lever Handle is only lifted partially, door may not

lock.

■■■■ Egress exit by pressing down Lever Handle.

■■■■ Do not use chemicals or abrasive materials to clean lock.

Insert battery housing with,

batteries into the inner lock

(make certain batteries are in

the correct direction)

■■■■ Lock Door from Inner Lock

Unlock Door

Lift up lever handle to

lock door

Press down lever handle

to unlock door

■■■■ How to use emergency key

Cam Lock Push the key into key hole

and hold it firmly and then

rotate down to unlock door

Please disconnect the battery

pack for 2 minutes whenever

you use the emergency cam

lock and reset it.

Specification and Operation

●●●● Interconnected dead bolt and lever lock.

●●●● Stand alone 4 AA batteries.

●●●● Low battery warning indicator.

●●●● Green Light: Access Code Accepted

●●●● Orange Light: Low Battery

●●●● Passage/Entrance or storeroom function at your choice(included in this lock).

●●●● 4 AA batteries not included.

● How to lock door

Just lift up lever handle to lock door.

● How to unlock door

Enter correct code (＊＊＊＊1 2 3 4 5 6 #) and then press down lever

handle to unlock door