Copyright jp Kabegami
Product name Key Features XNR/H 6809 Standard type XNR6840V VaRTM(Infusion) type of XNR6840
*product under development
Product name Key Features XNR/H 6842 Standard type XNR6840P Prepreg type of XNR6840 Figure1:Hybrid molding(Prepreg & VaRTM)
*product under development
For Adhesive Product name Key Features XNR6852F Film sheet type, High toughness, High elongation
Figure2 :Film sheet adhesive
Product name Product name Product name XNR/H 6951-3 XNR/H 6950 XNR6830/H6841
Figure5 : Burning test(Before & After)
Figure3 :Groove filling and trimming Figure4 :Low density epoxy compound Figure6 : Image of light cover
Nagase ChemteX Corporation Nagase Co & LTD.,(Harima Second Factory) (Grobal Trading Company)Add :236, Tatshnocho-nakai, Add: 5-1, Nihonbashi-Kobunacho,tatsuno, Hyogo, 679-4124, Japan Chuo-ku,TokyoTEL: +81-791-63-1054 TEL:81-3-3665-3784FAX: +81-791-63-2302 FAX:81-3-3665-3980URL: http://www.nagasechemtex.co.jp URL:http://www.nagase.co.jp
For Interior-Lighting system-
DENATITEEPOXY RESIN for Aeronautics
For RTM / Infusion
For Prepreg
For Groove filling For Honeycomb Structure-Low density epoxy compound-
CFRP
Model
Trimming
ISO 9001
Contact person
Groove filling
Viscosity (mPa・s) at 25℃ Mix ratio Work time (min) Gel time (min)
Resin / Hardener / Mixture R : H (wt%) 25℃/ 40℃ /60℃ 60℃ / 80℃
XNR/H 6809 800 / 80 / 260 100 : 95 - / 140 / 60 '- / 90 - / - / 130 (at 120℃) - 120(at 120℃) 100(at 150℃)
Flexural strength / modulus Impact strength Tg ISO 527-1 at 25℃ ISO178 at25℃ ISO179 25℃ DSC N/mm2 / Gpa / % N/mm2 / Gpa KJ/m2 ℃
XNR/H 6809 135 / 3.2 27 115160 / 4.0 - 195
Viscosity (Pa・s) at 25℃ Mix ratio Work time (min) Gel time (min)
Resin / Hardener / Mixture R : H (wt%) 25℃/ 40℃ /60℃
XNR 6842 1200 / / - - / - / - 65min(110℃)
Flexural strength / Modulus Impact strength Tg Standard ISO 527-1 at 25℃ ISO 178 at25℃ ISO 179 25℃ DSC
Unit N/mm2 / Gpa / % N/mm2 / Gpa KJ/m2 ℃
XNR 6842 102 / 2.5 150 102
Form Thickness Work time (min) Curing requirement
(μm) 25℃/ 40℃ /60℃
Non-woven scrim 120~130 - / - / -T-Peel Strength Impact strength Tg
ISO11339 at25℃ ISO179 25℃ DSCN/25mm KJ/m2 ℃
93 - 100
Viscosity (Pa・s) at 25℃ Mix ratio Work time (min) Gel time (min) Resin / Hardener / Mixture R : H (wt%) 25℃/ 40℃ /60℃ 60℃ / 80℃
408 / 80 / 300 100:22 30 / / 160 min (at 25℃)208 / 192 / 330 100:50 - / 160 / 60 - / -
10/0.55/6.3 100:160 / / - / 30Flexural strength / Modulus Impact strength Tg
Standard ISO 527-1 at 25℃ ISO 178 at25℃ ISO 179 at 25℃ DSCUnit N/mm2 / Gpa / % N/mm2 / Gpa KJ/m2 ℃
/ - 85 / / / - 208
131 / 3.3 17 92
Nagase ChemteX Corporation Nagase Co & LTD.,(Harima Second Factory) (Grobal Trading Company)Add :236, Tatshnocho-nakai, Add: 5-1, Nihonbashi-Kobunacho,tatsuno, Hyogo, 679-4124, Japan Chuo-ku,TokyoTEL: +81-791-63-1054 TEL:81-3-3665-3784FAX: +81-791-63-2302 FAX:81-3-3665-3980URL: http://www.nagasechemtex.co.jp URL:http://www.nagase.co.jp
XNR6840V(P)
XNR6840V(P)
XNR6852F
XNR6852F
XNR/H6951-3XNR/H6950XNR6830/H6841
ISO604 at 25℃
Unit N/mm2 / Gpa21 - / -
Unit Standard
For Adhesive
95 / 2.4 / / -
For Groove filling / Honycomb Structure / Mould
ISO604 at 25℃
N/mm2 / GpaXNR/H6951-3XNR/H6950XNR6830/H6841
/ / 68 / 2.1
85℃ 45min + 130℃ 1h4h 80℃ + 2h 120℃ + 6h 180℃
24h 25℃ + 5h 50℃
Tensile strength / Modulus / Elongation Compressive strength/modulus
Curing requirement
- / - / -
Compressive strength/modulus
115 / 3.1 ' 190 / 4.0
For RTM / Infusion
6h 80℃+ 2h 120℃
N/mm2 / Gpa
ISO 604 at 25℃
N/mm2 / Gpa 84 / 2.4
For Prepreg
2h 110℃ + 5h 150℃
Tensile strength / Modulus / Elongation Compressive strength/modulus
N/mm2
5h 150℃ + 5h 200℃
DENATITE
Curing requirement
EPOXY RESIN for Aeronautics
Curing requirement
Tensile strength / Modulus / Elongation
86 / 3.3 / 5.0
ISO604 at 25℃
Single Lap Shear Strength Compressive strength/modulus Standard
8hr/110℃, 3hr/120℃, 1hr/150℃
ISO4587 at 25℃
63 / 2.0 / 15
What do you expect our products? High Tg? High CAI property? etc.Please contact us and tell your request. We are going to make our product improve!
http://www.nagasechemtex.co.jp
ISO 9001
Contact person