Date post: | 22-Oct-2015 |
Category: |
Documents |
Upload: | masoodibrahim12 |
View: | 12 times |
Download: | 1 times |
Oil Water Separator Coalescing PackEPS-Pack™ Module
DONG HAE I · N· D · U · S · T · R ·Y
EPS-Pack™ Coalescing Media
The End of the Oil Water Separator
With more than 3,500 installations in operation, This verified design grantees the consistent operating results and ease of maintenance
The heart of the oil water separation – EPS-Pack provides the most effective removal oil and solid with the lowest cost in any given field especially storm water management.
Egg Plate Separator –A Patented Coalescing Module
EPS-Pack integrates inclined channels set at 45˚ angle from the horizontal and patented bumps underside of plates which allow oil drops to collect on the underside of the plates and form larger globules rising upward to the surface of the water. By Stoke’s Law, larger diameter drops of oil will rise to surface of the water faster. Furthermore, the corrugated plate with set 45˚ enhances separation and minimizes the risk of plugging the media. In Sludge hoppers design, the bottom shape of “V” or pyramid systems allows the solid sludge to converge into the hoppers for easy on-going maintenance of the oil water separator.
Features and Benefits
• High Efficiency• Bumps Underside of EPS-Pack™ Plates• Ease of Cleaning EPS-Pack™ Plates• Cross flow Processing• Adjustable Plates Gab• Horizontal and Vertical Set of
EPS-Pack™• Hybrid Solutions• Over 50 years Life Designed with
UV-protected polypropylene
The Most Efficient Design
EPS-Pack can remove free oil down to 10 ppm with less than 20 microns in size by only the configuration and the arrangement number of plates.
Furthermore, EPS-Pack has arranged parallel to each other with different spacing gaps.
• EPS P-8 Maximum efficiencyHeavy Oil and Less Solid
• EPS P-16 Standard
• EPS P-50 Minimum maintenanceHeavy Solid and Less Oil
Hybrid System – Cost Effective
EPS-Pack is the only one coalescing media that provides hybrid system.
To reduce costs, it’s possible to construct a hybrid EPS-Pack which contains all types of models, the bigger spacing gap of EPS Pack at the front and end and the smaller spacing gap of EPS pack at the between them.
Bumps Underside of Plates
Refer to page 3
Vertical and Horizontal Sets
Refer to page 3
Section one / Performance EPS-Pack™ Module
Performance - Impossible To Obtain With The Others
Hybrid System
The EPS-Pack is the only coalescing media that offers hybrid system. Generally, as the spacing between any coalescing plates decrease, efficiency well increases, and the gaps increase, both maintenance and efficiency decrease. Plates spacing is the same meaning of surface area. To correct this problem the EPS packs can be arrange the pack with different gap. The bigger spacing gap of EPS Pack at the front and end and the smaller spacing gap of EPS pack at the between them
Vertical and Horizontal configuration
EPS-Pack is the only coalescing media that provides two ways installation; vertical and horizontal sets. As mentioned above, coalescing media plates set 45 angles has weakness of sludge separation although minimizing the risk of plugging. To correct this problem, EPS-Pack provides vertical and horizontal sets. In field with much sludge, horizontal installation can be applied and in less sludge but much oil field vertical installation can be applied.
Underside of EPS-Pack plates incorporates that patented bumps which makes more surface area allow oil drops to collect on the underside of the plates, and form larger globules which then rise toward the surface of the water. By demonstrated by Stoke’sLaw, larger diameter drops of oil will rise to surface of the water faster.
Ease of Maintenance
The EPS-Pack is designed for semi-permanent using and to ease of cleaning. When using a dense packs, clogging of the oil and solids inside the packs appears. To correct this problem, the entire coalescing pack can be pulled out by crane or any operator, and cleaned with high pressure water. Not necessary to clean every weeks or month, but every 6,000 hours.
Bumps Underside of Plates
OILOIL
ARISED
radial structure
UDGE CLEANING SYSTEM
SLUDGE OUTLET
OIL
SLUDGE CLEANING SYSTEM
SLUDGE OUTLET
OIL HOLE
EPS PLATESLUDGE HOLE
EPS PLATE BUMPS
OIL ARISED
Horizontal Installation
Vertical Installation
111 – Oil hole115 - Bumps117- Sludge hole
Performance - Impossible To Obtain With The Others
• Power Plant• Equipment washdown• Stormwater runoff•Transportation facilities• Manufacturing facilities• Machinery coolant and tramp oil recovery• Automotive industry• Sewage treatment plant • Grinding and milling machinery
• Airport• Railroad• Bulk Plant• Landfill • Oil drilling • Miner industry• Ocean Tunnel• Oil refineries• Waste water treatment plant•Marine equipment
Wide range of applied fields
Adjustable Plates Gab
EPS Pack with spacing down to 0.3 inches have been developed successfully. According to API Publication 421, the typical range of spacing between the plates is 0.75 to 1.5 inches. Packs with spacing from 8mm to 30 mm can be used.
Egg Shape Plate with 45 degrees
The EPS-Pack provides egg shape plate set at 45 degrees. The angle of the plates should be somewhere between 45 and 60 degrees. The Pack with 60 degrees should be used if significant solids in the separator appears. However, EPS Pack with 45 degrees can be used any fields by hybrid system.
The lowest Reynold’s Number
The plate length never exceed 600mm in the EPS-Pack design. It yields a low Equivalent Diameter, further reducing fouling potential and is unique to the EPS-Pack design. A low Equivalent Diameter also leads to a low Reynold’s number, which describes the lower the number the more efficient the coalescing. With lesser turbulence within the coalescing media, there will be more oils and solids removal by Stoke’s Law. Dong Hae has the lowest Equivalent Diameter in the industry as well as the lowest Reynold’s number. Reynold’snumber of Dong Haeis between 350-370 for it's standard separator design criteria.
Section Two / Design EPS-Pack™ Module
General Arrangements
Isometric view of EPS-Pack
Isometric view of EPS-Pack assembled
Top view and side view of EPS-Pack
General Arrangements
Value engineered structures
EPS-Packs™ are the only manufacturer system which can offer a complete value engineered hybrid system utilizing all three EPS Packs to create a customized solution based on the oil-water requirements and environment condition for any given project. When integrated as a hybrid structure, a complete value engineered solution can be adopted for any given project. To reduce costs, it’s possible to construct a hybrid EPS-Pack which contains all types of models, the bigger spacing gap of EPS Pack at the front and end and the smaller spacing gap of EPS pack at the between them
Hybrid – EPS-Pack™ range of modular units
creating cost-effective hybrid system
EPS-Pack ™P 8 EPS-Pack ™P 16 EPS-Pack ™P 50
Section Three / Comparing Media Pack EPS-Pack™ Module
CPI Vs. EPS-Pack ™
After
Before
CPI Price
$241.00 / ft3 $7,950.00 / m3
Fibrous Mesh Pack Vs. EPS-Pack ™
Before
After
Fibrous Mesh Pack Price
$120.00 / ft3 $3,960.00 / m3
Vertical Tube Coalesce Vs. EPS-Pack ™
After
Before
Vertical Tube Coalesce PRICE
$75.00 / ft3 $2,480 / m3
• Available for PVC sheet for UV-protection, refer to page 5
Designed for use in lower viscosity than engine oil with a spacing of:
8 mm
EPS-Pack ™ P-8
Technical Specification Overview
Unit Type EPS Pack P-8
Product code EPS P-8
Dimensions 0.6m x 0.3m x 0.334m high1.97ft x 0.984ft x 1.06ft high
Total volume 0.058 m3
2.048 ft3
Unit weight 9 Kg
Surface area 13.4 m2
144 ft2
Plate spacing 8 mm0.03 ft
Number of plates 30 plates
Material of plate UV-Protected Polypropylene
Technical Specification Overview
Unit Type EPS Pack P-16
Product code EPS P-16
Dimensions 0.6m x 0.3m x 0.334m high1.97ft x 0.984ft x 1.10ft high
Total volume 0.060 m3
2.12 ft3
Unit weight 5.1 Kg
Surface area 7.59 m2
81.7 ft2
Plate spacing 16 mm0.05 ft
Number of plates 17 plates
Material of plate UV-Protected Polypropylene
• Available for PVC sheet for UV-protection, refer to page 5
Designed for use in higher viscosity or containing much sludge spacing of:
16 mm
EPS-Pack ™ P-16
Designed for use in high viscosity, a large oil drop such as bunker oil & crude oil with a spacing of:
30 mm
Technical Specification Overview
Unit Type EPS Pack P-50
Product code EPS P-50
Dimensions 0.6m x 0.3m x 0.308m high1.97ft x 0.984ft x 0.09ft high
Total volume 0.055 m3
1.94 ft3
Unit weight 3 Kg
Surface area 4.47 m2
48.1 ft2
Plate spacing 30 mm0.10 ft
Number of plates 10 plates
Material of plate UV-Protected Polypropylene
• Available for PVC sheet for UV-protection, refer to page 5
EPS-Pack ™ P-50
EPS-Full Pack ™
Technical Specification Overview
Unit Type Full EPS Pack Cartridge Type
Product code EPS-Full Pack
Dimensions 1.21(L) m x 1.135(W) m x 1.22(H) m1.97ft x 0.984ft x 0.09ft high
Frame Material SA240-304
Unit weight 200Kg
Plate spacing 8mm / 16mm / 30 mm 0.03ft / 0.05ft / 0.10 ft
Number of Packs 32 unit packs
Material of plate UV-Protected Polypropylene
Application – everywhere for water separation
Above Ground
Application