E:Revit Projectsx1-109 USI Orr Ctr Adm & Reg Office...

2017 BUILDING CODE SUMMARY:

APPLICABLE CODESGENERAL ADMINISTRATIVE RULES (GAR) 675 IAC 122014 INDIANA BUILDING CODE (2012 IBC) 675 IAC 13-2.62014 INDIANA MECHANICAL CODE (2012 IMC) 675 IAC 18-1.62014 INDIANA FIRE CODE (2012 IFC) 675 IAC 22-2.52012 INDIANA PLUMBING CODE (2006 IPC) 675 IAC 16-1.42009 INDIANA ELECTRICAL CODE (2008 NFPA 70) 675 IAC17-1.82010 INDIANA ENERGY CONSTRUCTION CODE(ASHRA 90.1, 2007 EDITION, AS AMENDED) 675 IAC 19.3

EXISTING BUILDING AREALOWER LEVEL: 25,772 S.F.FIRST FLOOR: 23,850 S.F.SECOND FLOOR:21,634 S.F.THIRD FLOOR: 16,216 S.F.TOTAL 87,472 S.F.

RENOVATION AREA: 3,389 S.F.

SEISMIC DESIGN CATEGORYCATEGORY C

OCCUPANCY CLASSIFICATIONSOFFICE: GROUP B OCCUPANCY (EDUCATION ABOVE 12TH GRADE)

CONSTRUCTION TYPE:TYPE II-B FULLY SPRINKLED

FIRE RESISTIVE REQUIREMENTSBUILDING ELEMENTS

STRUCTURAL FRAME - 0 HOURFLOOR CONSTRUCTION - 0 HOURROOF CONSTRUCTION - 0 HOURBEARING WALLS - 0 HOURNON-BEARING WALLS - 0 HOUR

1968 BUILDING CODE SUMMARY:

PROJECT DESCRIPTION:NEW CLASSROOM BUILDING TO BE BUILT AT THE UNIVERSITY OF SOUTHERNINDIANA IN EVANSVILLE, INDIANA IS THREE (3) STORIES IN HEIGHT ANDINCLUDES A BASEMENT. THE BUILDING AREA UNDER BASE BID IS 68,100 S.F.A CENTRAL ATRIUM SPACE CONNECTS FLOORS 1 THROUGH 3.

BUILDING HEIGHT:3 STORIES PLUS BASEMENT AND MECHANICAL MEZZANINE.

BUILDING TYPE:IBC TYPE II, 1-HOUR.

OCCUPANCY CLASSIFICATION:GROUP B DIVISION 2.

NUMBER OF OCCUPANTS:1ST FLOOR:2ND FLOOR:3RD FLOOR:BASEMENT:

22990226058

FIRE SUPPRESSION:THE BUILDING IS ENTIRELY PROTECTED THROUGHOUT WITH ASUPERVISED, AUTOMATIC FIRE EXTINGUISHING (SPRINKLER)SYSTEM.

ALLOWABLE FLOOR AREA:BASIC ALLOWABLE = 18,000 S.F. (TABLE 5C). BASIC ALLOWABLE AREAMAY BE MULTIPLIED BY 2 IN ACCORDANCE WITH SECTION 505(b) =36,000 S.F.

ALLOWABLE AREA INCREASES:SEPARATION ON 3 SIDES GREATER THAN 60' ALLOWS 100% INCREASE INALLOWABLE AREA; THEREFORE, 36,000 S.F. + 100% = 72,000 S.F.

FIRE RESISTIVE REQUIREMENTS:NEW CONSTRUCTION IS STRUCTURAL STEEL FRAME WITH 5" POURED-IN-PLACE COMPOSITE CONCRETE FLOOR SLAB. STANDING SEAM METAL ROOFCOVERING IS FIRE-RETARDANT IN ACCORDANCE WITH SECTION 3203(e).

FROM TABLE #17A:

A. STRUCTURAL FRAME 1 HOURB. CEILING / FLOOR ASSEMBLY: 1HOURC. CEILING / ROOF ASSEMBLY: 1 HOURD. SHAFT ENCLOSURES: 1 HOURE. INTERIOR PARTITIONS: 1 HOURF. STAIR ENCLOSURE: 1 HOUR

(SEC. 3309(a))G. CORRIDOR PROTECTION: NOT REQUIRED -

SEC. 3305(g)) EXC. 5

HANDICAP ACCESS:AN ELEVATOR IS PROVIDED FOR ACCESS TO THE FLOOR AREAS. TOILETFACILITIES COMPLY WITH SECTION 511 WITH RESPECT TO CLEAR SPACE,DOOR SWINGS, GRAB BARS, ETC.

EXITS:A. EXITING REQUIREMENTS:

FLOOR1ST2ND3RDBASEMENT

*INCLUDES CASCADE REQUIREMENTS.

B. TRAVEL DISTANCES: 100' FROM TENANT DOORS INACCORDANCE WITH SECTION 1715(d).

# OF EXITS REQ'D2322

EXIT WIDTH REQ'D*20.720.75.21.2

PROJECT LOCATION

USI CAMPUS

WEST LLOYD EXPRESSWAY

UN

IVER

ISTY PA

RKW

AY

PROJECT AREA

REFERENCE SYMBOLS:Room name

101A150 SF

ROOM NUMBER

101 DOOR NUMBER

1

A1.1

1A1.1

1

WALL SECTION/ SECTION DETAIL

A1.1ENLARGED DETAIL

INTERIOR ELEVATION

ELEVATION REFERENCE

DETAIL NUMBER

SHEET NUMBER

DETAIL NUMBER

SHEET NUMBER

ELEVATION NUMBER

SHEET WHERE DRAWN

A

M

R

ED

N

D

STATE OF

PE60900441

OF I

SS

E

OI

N

R

M

P

E

NLA

I A

E

N A N

GI

ER

AN

W

T

HT EGE

. BEIST

J

R

R CKO

NO.R R

ED

A

N

PE10505044PROF I N

O

ESSI LAN

D I

E

NA

STATE OF

No.

EN

GI

RE

RAT

GAY E

NW S

TSI

.RENE I H

T

DNI

AI AN

No. AR10100128

STATE OF

GER

RTSI EDE

ARCH I T E

CT

JACK

SON R

ICHARDFABER

Orr Center:

Registrar Renovation

8600 University BoulevardEvansville, Indiana

Project No. 1701-109Date: March, 2017

03/14/2017 03/14/2017

SHEET INDEXSHEET NO. SHEET NAME

GENERALCov COVERGENERALG1.1 GENERAL INFORMATION & DEMOLITION PLANARCHITECTURALA1.1 FLOOR PLANS, PLAN DETAILSA2.1 DOORS SCHEDULE, INTERIOR ELEVATIONS, DETAILSA2.2 FRAME DETAILSA3.1 FIRST FLOOR FINISH PLAN AND SCHEDULEPLUMBINGP1.1 PLUMBING PLANSMECHANICALM1.1 FIRST FLOOR HVAC PLANM2.1 MECHANICAL DETAILS & SCHEDULESELECTRICALE1.1 ELECTRICAL LEGEND AND BUSSING DIAGRAME2.1 FIRST FLOOR ELECTRICAL DEMOLITION, POWER AND SYSTEMS PLANE3.1 FIRST FLOOR LIGHTING PLAN

1" = 400'-0"USI CAMPUS

1/16" = 1'-0"FIRST FLOOR PROJECT AREA

4'0' 8' 16'

North

North

GENERAL DEMOLITION NOTES:FIELD VERIFY ALL EXISTING CONDITIONS. NOTIFY ARCHITECT/ENGINEERIMMEDIATELY OF ANY DISCREPANCIES THAT EXIST.

REMOVE EXISTING CONSTRUCTION AS NOTED AND WHERE SHOWN DASHED.CONTRACTOR IS RESPONSIBLE FOR ALL DEMOLITION REQUIRED FOR THEINSTALLATION OF NEW WORK AND FOR THE PROTECTION OF ITEMS TO REMAIN.

CONTRACTOR IS RESPONSIBLE FOR ANY DEMOLITION THAT IS NOT SHOWN ONTHE DEMOLITION DRAWINGS BUT IS REQUIRED FOR THE NEW CONSTRUCTION.

REFER TO DEMOLITION REFERENCE NOTES FOR ADDITIONAL WORK ITEMS.

THE OWNER HAS FIRST RIGHT OF REFUSAL OF ALL SALVAGEABLE ITEMSREMOVED DURING DEMOLITION INCLUDING FURNISHINGS AND MILLWORK.

REFER TO MECHANICAL AND ELECTRICAL PLANS FOR REMOVAL AND RELOCATIONAND REROUTING OF THE EXISTING UTILITIES.

DEMOLITION OF EXISTING UTILITIES SHALL BE MADE SO THAT SERVICE TO OTHERAREAS UTILIZED BY THE OWNER ARE NOT INTERRUPTED. PROVIDE TEMPORARYUTILITIES, ISOLATION VALVES, DISCONNECTS, ETC. WHERE REQUIRED DURINGDEMOLITION AND NEW CONSTRUCTION

IF CONTRACTOR BECOMES AWARE OF ANY LOAD BEARING POINTS WITHINDEMOLITION NOT NOTED ON THE DRAWINGS, THE CONTRACTOR SHALL NOTIFYARCHITECT/ENGINEER PRIOR TO REMOVING THAT CONSTRUCTION.

PATCH OPENINGS IN WALLS, CEILINGS AND FLOOR RESULTING FROM ALLDEMOLITION WORK. PATCH ALL OPENINGS IN EXISTING CONSTRUCTION AS ARESULT OF ELECTRICAL, PLUMBING AND HVAC MODIFICATIONS. PATCH ALLABOVE WITH MATCHING MATERIALS, CONSTRUCTION AND RATING UNLESS NOTEDOTHERWISE.

PROTECT EXISTING FINISHES AND EQUIPMENT DURING DEMOLITION.

PATCH AND REPAIR ALL EXISTING CONSTRUCTION AND FINISHES DAMAGEDDURING THE DEMOLITION WORK REQUIRED FOR THIS PROJECT. THE REQUIREDREPAIR WORK SHALL MATCH THE NEW CONSTRUCTION AND FINISHES UNLESSNOTED OTHERWISE.

PATCH AND SEAL ALL FLOOR, WALL, AND CEILING PENETRATIONS THAT BECOMEEXPOSED DURING DEMOLITION.

SAW CUT AND PATCH EXISTING FLOOR SLABS AS REQUIRED FOR NEW PIPING.REFER TO PLUMBING DRAWINGS.

REFER TO MECHANICAL, ELECTRICAL, AND PLUMBING PLANS FOR SIZES ANDLOCATIONS OF CUTOUTS.

ALL EXISTING FIRE RATINGS OF THE WALLS, FLOOR AND CEILINGS SHALL BEMAINTAINED.

ALL DEMOLITION ACTIVITY SHALL BE COORDINATED WITH THE UNIVERSITY OFSOUTHERN INDIANA AND THEIR SCHEDULED ACTIVITIES.

OWNER TO REMOVE AND STORE ALL EXISTING FURNITURE.

REMOVE EXISTING CEILINGS WHERE REFLECTED CEILING PLANS INDICATE NEWCEILINGS.

PROVIDE DUST BARRIERS AS REQUIRED TO PREVENT MIGRATION TO AREASOCCUPIED BY OWNER. PROTECT ALL EQUIPMENT TO REMAIN. COORDINATEPROTECTION OF EXISTING EQUIPMENT WITH OWNER.

WHERE NEW FINISHES ON WALLS ARE SCHEDULED, ALL WALLCOVERING SHOULDBE REMOVED PRIOR TO FINISH WORK. PATCH AND REPAIR WALLS TO PROVIDE ALEVEL 4 FINISH PER GYPSUM ASSOCIATION GA 214-10 BEFORE PAINTING.

REFER TO FINISH PLANS AND SCHEDULES. ALL ROOMS INDICATED TO RECEIVENEW FINISHES SHALL HAVE EXISTING FINISHES REMOVED. PREP SUBSTRATESFOR NEW FINISHES INDICATED ON FINISH PLANS AND SCHEDULES.

SALVAGE ANY EXISTING TACK & CHALKBOARD. CONSULT OWNER FOR NEWLOCATION.

REFER TO DOOR SCHEDULE FOR ADDITIONAL REQUIREMENTS.

A.

B.

C.

D.

E.

F.

G.

H.

J.

K.

L.

M.

N.

P.

Q.

R.

S.

T.

U.

V.

W.

X.

Y.

DEMOLITION REFERENCE NOTES:REMOVE ENTIRE WALL CONSTRUCTION TO LIMITS SHOWN.

REMOVE EXISTING DOOR, HOLLOW METAL FRAME AND HARDWARE.

REMOVE EXISTING BASE AND WALL CABINETS, COUNTER, CASEWORKAND SHELVING IN THEIR ENTIRETY.

REMOVE EXISTING PLUMBING FIXTURE . REFER TO PLUMBINGDRAWINGS.

REMOVE EXISTING FLOORING, PLYWOOD SUBSTRATE AND METALFRAMING THIS AREA.

RELOCATE EXISTING FIRE EXTINGUISHER AND CABINET AS INDICATEDON FLOOR PLAN

REMOVE AND REINSTALL EXISTING CEILING GRID AS REQUIRED FORINSTALLATION OF NEW CONSTRUCTION.

REMOVE EXISTING DOOR AND HARDWARE, EXISTING FRAME TOREMAIN.

REMOVE VERTICAL GLASS PANEL AND ALUMINUM FRAME AT END OFWALL. CONTRACTOR HAS OPTION TO REUSE IF ABLE TO BE SALVAGEDAND IN GOOD CONDITION. REMOVE CAULK FROM EXTERIOR WINDOW.

REMOVE EXISTING STEPS.

REMOVE EXISTING WINDOW SHADE.

RELOCATE EXISTING REFRIGERATOR.

RELOCATE EXISTING DOOR AND FRAME TO DOOR OPENING 1086-2A.

SALVAGE EXISTING WALL BASE AND REINSTALL AS INDICATED ONFINISH PLAN.

1

2

3

4

5

7

6

8

9

10

11

12

13

14

5678

F

G

H

K

1

11

1

1

1

1 1

2

2

2

2

2

3

3

3

3

1

2

2

4

56

7

9 9

12

10

1111

1111

13

8

8

14

2

14

INTERIOR PARTITION METALSTUD GAUGE SELECTION CHART

16" O.C. STUD SPACING WITH ALLOWABLE DEFLECTION CRITERIA OF L\360

STUDDEPTH

MAXIMUM VERTICALUNBRACED SPAN IN FEET

(1 LAYER GYPSUMBOARD EACH SIDE)

MAXIMUM VERTICALUNBRACED SPAN IN FEET(2 LAYER GYPSUM BOARD

EACH SIDE)

STUDGAUGE

1-5/8" 8'-3" 9'-0" 252-1/2" 10'-9" 11'-9" 252-1/2" 11'-6" 12'-3" 222-1/2" 12'-0" 14'-0" 203-5/8" 14'-0" 14'-9" 253-5/8" 15'-0" 15'-9" 223-5/8" 15'-7" 17'-8" 20

4" 15'-0" 15'-9" 254" 16'-3" 16'-9" 224" 16'-10" 16'-11" 206" 20'-0" 20'-0" 256" 22'-0" 22'-9" 226" 22'-10" 24'-11" 20

MATERIALWALL TYPE LEGEND

G

NOMINAL/ ACTUAL SIZEMETAL STUD

METAL STUD WALLS

3 3-5/8" METAL STUD

SURFACESA 1 LAYER 5/8" TYPE "X" GYP. BD. ON ONE SIDE OF METAL STUD WALL

B 1 LAYER 5/8" TYPE "X" GYP. BD. ON EACH SIDE OF METAL STUD WALL

CONDITIONS1 WALL AND FINISH EXTENDS 6" ABOVE HIGHEST ADJOINING CEILING.

BRACE TOP OF WALL AS REQUIRED.

EXAMPLEG3.B.1 3-5/8" METAL STUD WITH 5/8", TYPE "X", GYP. BD. EACH SIDE. EXTEND WALL

AND BOTH SIDES OF GYPSUM BD. EXTENDS 6" ABOVE HIGHEST ADJOININGCEILING .

GENERAL NOTES1. ALL PARTITIONS EXTEND 6" ABOVE CEILING ABOVE UNLESS NOTED OTHERWISE.

2. STORAGE ROOMS GREATER THAN 100 SF SHALL BE CONSTRUCTED TORESIST THE PASSAGE OF SMOKE.

3. PROVIDE 25 GAUGE METAL STUDS, UNLESS NOTED OTHERWISE ORREQUIRED BY METAL STUD GAUGE SELECTION CHART.

4. PROVIDE (2) 20 GAUGE METAL STUDS AT ALL WINDOW AND DOOR JAMBS.

5. ALL FIRE-RATED PARTITIONS ARE TO BE CONSTRUCTED IN ACCORDANCEWITH APPROPRIATE U.L. ASSEMBLY.

6. REFER TO REFLECTED CEILING PLANS FOR LOCATIONS OF SOUNDATTENUATION BLANKETS.

7. PARTITIONS NOT REQUIRED TO EXTEND TO STRUCTURE ABOVE SHALL BEBRACED BY ATTACHING ALTERNATING DIAGONAL STUDS 48" O.C. (MAX.)FROM TOP OF PARTITION TO STRUCTURE ABOVE.

8. FIRE RATED WALLS TO RECEIVE ELECTRICAL OUTLET BOXES SHALLCONFORM TO THE FOLLOWING GUIDELINES. METALLIC OUTLET BOXESSHALL BE UTILIZED IN WALLS AND PARTITIONS WITH A TWO HOUR OR LESSCLASSIFICATION. THE SURFACE AREA OF INDIVIDUAL BOXES SHALL NOTEXCEED 16 SQUARE INCHES. THE AGGREGATE SURFACE AREA OF BOXESSHALL NOT EXCEED 100 SQUARE INCHES IN ANY 100 SQUARE FEET. BOXESLOCATED ON OPPOSITE SIDES OF RATED WALL OR PARTITIONS SHALL BESEPARATED BY A MINIMUM HORIZONTAL DISTANCE OF 24 INCHES.

GENERAL FACILITY NOTES:THE CONTRACTOR SHALL ADHERE TO UNIVERSITY OF SOUTHERN INDIANAREQUIREMENTS FOR OUTSIDE CONTRACTORS.

COORDINATE ALL REQUIREMENTS WITH UNIVERSITY OF SOUTHERNINDIANA (FOR CONSTRUCTION) DELIVERY OF MATERIALS TO THE SPACE,CONSTRUCTION TRAFFIC TO AND FROM THE SPACE, KEEPING CORRIDORSFREE FROM DUST AND DEBRIS, CLEANUP AND DISPOSAL OF MATERIALS,ETC.

THE ARCHITECT AND CONTRACTOR SHALL DO A PRE AND POST-CONSTRUCTION WALK THROUGH OF THE EXISTING COMMON AREAS OFTHE PROJECT AREA THAT THE CONTRACTOR WILL USE FOR ACCESS TOTHE PROJECT SITE TO REVIEW EXISTING CONDITIONS AND FINISHES. IF ITIS DETERMINED THAT AREAS WERE DAMAGED BY THE CONSTRUCTIONACTIVITY, THE DAMAGE SHALL BE REPAIRED AT THE COST OF THECONTRACTOR.

EXISTING ITEMS THAT HAVE TO BE RELOCATED SHALL BE RE-INSTALLEDAS IF IT WAS THE ORIGINAL INSTALLATION UNLESS NOTED OTHERWISE.

IF THE CONTRACTOR BELIEVES A DUMPSTER IS REQUIRED FOR THISPROJECT, COORDINATE THE LOCATION WITH THE UNIVERSITY OFSOUTHERN INDIANA.

1.

2.

3.

4.

5.

DNI

AI AN

No. AR10100128

STATE OF

GER

RTSI EDE

ARCH I T E

CT

JACK

SON R

ICHARDFABER

Drawing No:

Architect's Project No: Date:

Sheet title:

Revisions:

The drawings, specifications and other documents, including those in electronicform prepared by Hafer for this project are instruments of Service, and may beused solely with respect to this project. The documents may not be reproducedor modified by a third party without first obtaining the express written consent ofHafer. Authorized use of electronic media or file does not guarantee that thesefiles contain complete and accurate information. In order to insure the accuracyof the information contained and that no changes or modifications have beenmade, these files must be compared to the project's contract documents withstamped and sealed certification and applicable approved modifications.

In association with:

Orr Center:



Designed By: Drawn By: Checked By:

March, 20171701-109

G1.1

GENERAL INFORMATION &DEMOLITION PLAN

1/8" = 1'-0"FIRST FLOOR DEMOLITION PLAN

2'0' 4' 8'

North

# Description Date

DN

FLOOR PLAN REFERENCE NOTES:EXISTING MECHANICAL CHASE TO REMAIN.

ALIGN NEW CONSTRUCTION TO EXISTING.

RELOCATED REFRIGERATOR. REFER TO ELECTRICAL AND PLUMBINGDRAWINGS FOR ADDITIONAL INFORMATION.

RELOCATED FIRE EXTINGUISHER AND CABINET TO BE INSTALLED @ 48"TOP.

CLOSET SHELF WITH ROD. REFER TO DETAIL 8, SHEET A2.1.

CORNER GUARD (CG1). SEE FINISH SCHEDULE FOR ADDITIONALINFORMATION. CORNER GURAD TO START AT TOP OF BASE AND EXTENDTO CEILING LINE WITH NO GAP.

END WALL PROTECTION (EWP1). SEE FINISH SCHEDULE FORADDITIONAL INFORMATION. CORNER GURAD TO START AT TOP OF BASEAND EXTEND TO CEILING LINE WITH NO GAP.

PATCH EXISTING WALL TO MATCH ADJACENT. PREPARE SURFACE ASREQUIRED TO RECEIVE NEW FINISH. REFER TO FINISH PLAN FORADDITIONAL INFORMATION.

1

2

3

4

5

7

6

8

5678

F

G

H

K

WAITING1075

OPEN OFFICE1076

CONFERENCE1077

OFFICE1078

OFFICE1079OFFICE

1080OFFICE

1081

OFFICE1082

OFFICE1083

OFFICE1084

OFFICE1085

BREAK1086-1

STORAGE1086-2

VESTIBULE1087

CORR1074

CORR1076-1

CORR1076-2

1086-1A

1086-1B1085A

1086-2B

1077

1086-2A

1076-1

1076

1078

1079

1080

1084

1083

1082

1081

A2.1

3

A2.1

5

A2.1

4

2

2

2

2

2

2

2

15' - 1 3/4" 4 7/8" 19' - 7 7/16" 4 7/8" 14' - 10 5/8"

G3.A.1G3.A.1G3.A.1

G3.A.1

G3.A.1

G3.A.1G3.A.1

10' - 8 15/16" 4 7/8" EQ 4 7/8" EQ 4 7/8" EQ 4 7/8" 20' - 2 1/8"

4 7/

8"3'

- 3"

4 7/

8"

1

14' -

2 7

/8"

7' -

6 1/

4"20

' - 5

"

G3.A.1

G3.A.1

FT4

WORK1076-3

A1.11

Sim

A1.11

Sim

FT6

A1.11

Sim

3

2

2

43' - 5 1/4" 9 3/8"2

2' - 5 1/2"

5

4

6

6

6

6

7

1' -

4 5/

8"1' - 2 5/8"

G3.A.1G3.A.1G3.A.1

6

6

8' -

0"

1075

8

12' -

4 7

/8"

13' -

11

9/16

"

1085B

A2.212 Sim

A2.212

A2.212

Sim

A2.26

A2.212

Sim

A2.23

A2.24

A2.24

A2.25

A2.25

1' - 4"

1' - 4"

5678

F

G

H

K

9' - 0"

9' - 0"9' - 0"

9' - 0"

9' - 0"

9' - 0"

9' - 0" 9' - 0" 9' - 0" 9' - 0"

9' - 0"

9' - 0"

8' - 8"

9' - 0"9' - 0"

OFFICE1085

BREAK1086-1

STORAGE1086-2

WAITING1075

OFFICE1084

OFFICE1083

OFFICE1082

OFFICE1081

CONFERENCE1077

OFFICE1078

OFFICE1079

OFFICE1080

CORR1076-2

CORR1076-1

OPEN OFFICE1076

9' - 0"

9' - 0"

9' - 0"

5' -

9"5'

- 2"

EQ9'

- 0"

EQ

2

A1.1

3

A1.1

4

A1.1

WORK1076-3

7' - 0"

4

A1.1

4

A1.1

7' - 0"

9' - 0"

5

A1.1

9' - 0"7' - 0"

8' - 0"

EQ 10' - 0" EQ

C J

C J

C J

C J

C J

C J

1

2

2

2

3

A1.1

Sim

9' - 0"

3

A1.1

Sim

3

9' - 0"

1

1

3

A1.1

Sim

444

5

6

7

1' -

10"

2

A2.22

A2.2

2

A2.2

2

A2.2

1

A2.2

1

A2.2

8

A2.2

8

A2.2

8

A2.2

8

A2.2

8

A2.2

9

A2.2

9

A2.2

9

A2.2

66

6

6

68

9

2' x 4' LIGHT FIXTURE

RECESSED CAN LIGHT FIXTURE

EXIT FIXTURE

WALL MOUNTED LIGHT FIXTURE

2'-0" x 2'-0" SUSPENDEDACOUSTICAL CEILING PANELS

GYPSUM BOARD SOFFIT / CEILING

FINISH HEIGHT OF CEILING / SOFFIT A.F.F.0'-0"

HVAC RETURN AIR

HVAC SUPPLY DIFFUSER

REFLECTED CEILING PLAN SYMBOLS

RECESSED LIGHT FIXTURE

SURFACE MOUNTED LIGHT FIXTURE

"FAST SIZE" CEILING PANEL BY ARMSTRONG

C J CEILING CONTROL JOINT, REFER TODETAIL THIS SHEET

CUT DOWN 2 x 4 CEILING TILE

MUST NOT EXCEED A 1/6 SLOPE (10°).THE PERIMETER. ATTACHMENT WIRE

MUST NOT EXCEED A 1/6 SLOPE (10°).FROM THE WALL. ATTACHMENT WIREPERIMETER WALL A MAXIMUM OF 8"12 GA. HANGER WIRE ANCHORED TO

STRUCTURE ABOVE AND HUNG12 GA. HANGER WIRE ANCHORED TO

VERTICALLY A MAXIMUM OF 8" FROM

SPACER BAR BY USG OR SIMILARAPPROVED SYSTEM TO PREVENTPERIMETER COMPONENTS FROMSPREADING APART.

CONTINUOUS WALL ANGLE ANCHOREDTO PERIMETER WALL @ 24" O.C.

HANGER WIRE PERIMETER SUPPORTSWITH TWO ALTERNATIVES:

2.

1.8" MAX.

3/8" 9/16"

15/16"

MAX.

4"

GYPSUM BOARD CONTROL JOINT

5/8" GYPSUM BOARD

4 7/8"

6"

5/8" GYP. BOARD

METAL EDGE BEAD

3 5/8" METAL STUDS@ 24" O.C.

SUSPENDEDACOUSTICAL PANELCEILING SYSTEM


METAL EDGE BEAD

3 5/8" METAL STUDSBRACING @ 48" O.C.

ELEV., REFER TOCEILING PLAN

SUSPENSION WIRE


9/16" TEE

3 5/8" METAL STUDBRACING @ 32" O.C.

5/8" GYPSUMWALLBOARD

9/16" WALL ANGLE

METAL EDGE BEAD

REFER TO CEILING PLAN

VARIES



METAL STUDSCORNER ANGLE

3 5/8" METAL STUDBRACING @ 16" O.C.

VERTICAL WIRE HANGERANCHOR WITH MINIMUMWITHDRAWAL TENSIONCAPACITY OF 100 LBS. ORHIGHER, TYPICAL - PERANCHOR

ROOF OR FLOOR FRAMING

BRACE ANCHOR WITHMINIMUM COMBINEDWITHDRAWAL TENSIONAND SHEAR CAPACITY OF325 LBS. SHORT DURATIONADJUSTMENT MAY BEUSED IF PERMITTED BYPRODUCT'S EVALUATIONREPORT LISTING

4 TIGHT TURNSMINIMUM WITHIN 1 1/2"OF EYE, TYPICAL 12GAUGE WIRE MINIMUM3 TIGHT TURNS MINIMUM

WITHIN 1 1/2" OF EYE,TYPICAL - 12 GAUGEWIRE MINIMUM

90 D

90

45 MAX

45 MAX.

2" MAX

2" MAX

1 1/4" 8'-6"

6'-2"

5'-2"

MAX. LENGTH

1"

3/4"

EMT

PROVIDE VERTICAL STRUT- ELECTRICALMETALLIC TUBING (EMT) SLIPPED OVER VERTICALSUSPENDED WIRE AND CUT TO FIT SNUGLYAGAINST BOTH SUPPORTING STRUCTURE ABOVEAND CEILING RUNNER BELOW

4 TIGHT TURNS MINIMUM WITHIN 1 1/2" AT EACHEND OF DIAGONAL WIRE, TYPICAL

CROSS RUNNER

11 GAUGE WIRE BRACING, TYPICAL IN 4 DIRECTIONS,KEEP 6" CLEAR OF ANY UNBRACED HORIZONTALPIPING OR DUCTWORK

12 GA. VERTICAL WIREHANGER

MAINRUNNER OR UP TO 6'-8" USE: 3 1/2" x 1 1/4" 25 GA.

STEEL STUD ATTACHED TO RUNNERWITH 2-#10 SCREWS AND STRUCTUREABOVE WITH 3/16" DIAMETER POWDERDRIVEN PIN OR 2-#10 SCREWS

SEALANT (BOTH SIDES)

5/8" GYPSUM BOARD

(2) 3 5/8" METAL STUDS

TEMPEREDGLASS

EXISTING STORE FRONT FRAMING

EXISTING WINDOW SILL

EXISTING WINDOW SILL

PROVIDE NEW STOREFRONTFRAMING TO MATCH EXISTING.CONTRACTOR HAS OPTION TOREUSE EXISTING FRAMING IF ABLETO BE SALVAGED AND IN GOODCONDITION.

SEALANT

SEALANT

3-5/8" METAL STUDSBRACING @ 48" O.C.

SUSPENDEDACOUSTICALPANEL CEILINGSYSTEM

NOTE:REFER TO REFLECTED CEILING PLANFOR BULKHEAD LOCATION AND SIZES.

VARIES

LINE OFPARTITION WALL

5/8" GYP. BOARD

METAL EDGE BEAD

METAL STUDSCORNER ANGLE

3 5/8" METALSTUDS @24" O.C.

3 5/8" METALSTUDS @ 24" O.C.



6" SUSPENDEDACOUSTICAL PANELCEILING SYSTEM

SUSPENSIONWIRE

SUSPENDEDACOUSTICALCEILINGPANEL

SUSPENDEDGYPSUMBOARD

SUSPENDEDGYPSUM BOARDCEILING SYSTEM

6" CEILINGTRANSITIONTRIM


SUSPENSIONWIRE

SUSPENDEDACOUSTICALCEILING PANEL


ACOUTICAL /GYPSUM BOARDCEILINGTRANSITION TRIM

REFLECTED CEILING PLAN REFERENCE NOTES:PROVIDE ADDITIONAL CEILING GRID CROSS TEE AS REQUIRED TOACCOMMODATE LIGHT FIXTURE.

CUT DOWN 2X4 TILE.

REMOVE AND REINSTALL EXISTING CEILING GRID AS REQUIRED FORINSTALLATION OF NEW CONSTRUCTION.

NEW BLINDS TO MATCH EXISTING AS APPROVED BY ARCHITECT.

FACE OF BULKHEAD TO BE [PT2]. UNDERSIDE OF BULKHEAD TO BE[PT5].

FACE AND UNDERSIDE OF BULKHEAD TO BE PAINTED [PT5].

COORDINATE LIGHT FIXTURE LOCATION WITH ARCHITECT PRIOR TOINSTALLATION.

CONFIRM THIS WALL EXTENDS TO DECK ABOVE. SEAL ALLPENETRATIONS AS REQUIRED AND APPLY ACOUSTIC CAULKING.

MAINTAIN OR EXTEND WALL ABOVE TO FLOOR DECK ABOVE ANDSEAL ALL PENETRATIONS.

1

2

3

4

5

6

7

8

9

GENERALREFLECTED CEILING PLAN NOTES:

PROVIDE CONTROL JOINTS OR OTHER ISOLATING MEANS IN GYPSUMBOARD PANELS WHERE: (A) PARTITION, FURRING, SOFFIT, BULKHEAD, ORCEILING ABUTS A STRUCTURAL ELEMENT OR DISSIMILAR WALL ORCEILING, (B) CONSTRUCTION CHANGES WITHIN PLANE OF PARTITION ORCEILING, (C) PARTITION, FURRING SOFFIT, BULKHEAD OR CEILING RUNEXCEEDS 30'-0", (D) AS NOTED.

MINIMUM DISTANCE FROM A WALL SURFACE TO THE NEAREST CEILINGGRID TEE SHALL BE 6".

WALLS INDICATED ; SHALL BE METAL STUDS, 5/8"GYPSUM BOARD ON ONE SIDE AND SOUND INSULATION SHALL END 6"ABOVE CEILING.

REFER TO A1.1 FOR ALL ACOUSTICAL CEILING PERIMETER CONDITIONS.

REFER TO A3.1 FOR CEILING FINISH INFORMATION.

1.

2.

3.

4.

5.

GENERAL FLOOR PLAN NOTES:ALL DIMENSIONS ON FLOOR PLANS ARE FROM FACE OF FINISH GYPSUMBOARD UNLESS NOTED OTHERWISE.

PROVIDE WOOD BLOCKING IN WALLS AND CEILINGS AS REQUIRED FORINSTALLATION OF CASEWORK OR OTHER SURFACE MOUNTEDACCESSORIES AND/OR EQUIPMENT.

LOCATE HOLLOW METAL OR ALUMINUM DOOR FRAMES 4" FROM ADJACENTWALL, UNLESS NOTED OTHERWISE. PROVIDE MINIMUM OF TWO (2) 20 GAUGEMETAL STUDS AT HEAD AND JAMB OF DOOR OPENINGS.

CONTRACTOR SHALL VERIFY ALL DIMENSIONS THAT ARE SHOWN ON THEDRAWING.

FIRESTOPPING SHALL BE INSTALLED AT ALL PENETRATIONS OF THE FIRE-RATED WALLS AND MEET THE REQUIREMENTS OF THE FIRE-RATING OF THEWALL. THE FIRE STOPPING PRODUCTS SHALL BE "HILTI, INC." AND INSTALLEDPER THE MANUFACTURER'S INSTRUCTIONS WITH CERTIFIED INSTALLERS.

FIELD VERIFY ALL DIMENSIONS BEFORE FABRICATION OR INSTALLATION OFSHELVING AND MILLWORK.

ALL WALLS TO BE TYPE G3.B.1 UNLESS NOTED OTHERWISE.

FURNITURE SHOWN FOR PLANNING PURPOSES ONLY. FURNITURE IS NOT INCONTRACT.

1.

2.

3.

4.

5.

6.

7.

DNI

AI AN

No. AR10100128

STATE OF

GER

RTSI EDE

ARCH I T E

CT

JACK

SON R

ICHARDFABER

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

A1.1

FLOOR PLANS, PLAN DETAILS

1/8" = 1'-0"FIRST FLOOR PLAN

2'0' 4' 8'

North

1/8" = 1'-0"FIRST FLOOR REFLECTED CEILING PLAN

2'0' 4' 8'

North

1 1/2" = 1'-0"TYP. ACOUSTICAL CEILING EDGE DETAIL

3" = 1'-0"TYP. CEILING CONTROL JOINT (CJ)

1 1/2" = 1'-0"5 BULKHEAD DETAIL


1 1/2" = 1'-0"TYP. SUSP. ACOUSTICAL CLG. HANGER ATTACHMENT

1 1/2" = 1'-0"TYP. SUSP. ACOUSTICAL CLG. LATERAL BRACING

1 1/2" = 1'-0"1 PLAN DETAIL


1" = 1'-0"3 BULKHEAD DETAIL

# Description Date

SCHEDULE

SEE

SCH

EDU

LE

SEE

C

SCHEDULE

SEE

SCH

EDU

LE

SEE

A

8"

8" 8"

1' -

0"

1/4" TEMP.GLASS

SCHEDULE

SEE

SCH

EDU

LE

SEE

B

3' -

5"2'

- 9"

6"

8"

FIXEDPANEL

1/4" TEMP.GLASS

FROSTED VINYL FILM APPLIED TO GLASS.

PAINT FRAME AS INDICATED ON FINISH PLAN. (BASE BID ONLY)

MATCH EXISTING DOOR STAIN/FINISH.

ALTERNATE NO. 1 - ALUMINUM FRAMES.

RELOCATED DOOR AND HOLLOW METAL FRAME FROM EXISTING OPENING 1086.

EXISTING FRAME TO REMAIN.

EXISTING TO REMAIN.

SUPPLIED IN FURNITURE PACKAGE.

1.

2.

3.

4.

5.

6.

7.

8.

NOTES:

8

A2.2

12

A2.2

FT1

14' - 10 1/2"

2"8'

- 8"

2"

9' -

0"

14

A2.2

2" EQ EQ 2" 3' - 0" 2" EQ EQ 2"

BUTT JOINT W/SEALANT (TYP.)

12

A2.2Sim

13

A2.2

FT3

12

A2.2

14

A2.2

8

A2.2

2

A2.2

11' - 7 7/16"

2"1'

- 10

"5'

- 8"

1' -

2"2"

4 1/2"

1' - 0"2" 3' - 0" 2" EQ EQ 2"

FIXED TRANSOMPANEL TO MATCHDOOR FINISH

FROSTEDVINYL FILMCLEAR

CLEAR

9' -

0"

Sim3

A2.2

13

A2.2

3

A2.2

14

A2.2

7

A2.2

FT4

2"

9' -

0"

2"1'

- 2"

5' -

8"1'

- 10

"2"

FROSTEDVINYLFILM

CLEAR

CLEAR

14

A2.2FT5

2"3' - 0"2"EQ.EQ.2"

9' -

0"

2"1'

- 10

"5'

- 8"

1' -

2"2"


FROSTEDVINYL FILMCLEAR

CLEAR

REFER TO DETAILCALLOUT ON FLOORPLAN FOR JAMB DETAIL

REFER TO DETAIL CALLOUTON REFLECTED CEILINGPLAN FOR HEAD DETAIL

13

A2.2

3' -

8"3'

- 6"

7' -

2"

FT6

8' - 10 3/8"

2"2"

2"

11

A2.2

10

A2.2

FT2

1

A2.1

2

A2.1

2"8'

- 10

"

9' -

0"


EQ 2' - 9" 2' - 9" 2' - 9" EQ

EQ 2' - 9" 2' - 9" 2' - 9" EQ

6

A2.1

PL1

PL1

SS1

FILLER TO MATCHADJACENT, TYP.


1' - 9" 2' - 0" 1' - 9" 1"

1" 1' - 9" 2' - 0" 1' - 9" 1"

5' - 8"

6

A2.1

7

A2.1

PL1

PL1

SS1



6

A2.1

1" 3' - 0" 2' - 9" 3' - 0"

1"3' - 0"2' - 9"3' - 0"1"

8' - 11"

8' - 10"

PL1

PL1

SS1

FILLER TOMATCHADJACENT,TYP.

FILLER TOMATCHADJACENT,TYP.

1/2"

1' - 2"

3"2' - 0"

4"1/

2"

5"

3/4" PLASTICLAM. CLAD TOP

WOOD BLOCKINGSHELF BRACKETSBEYOND WITH CLIPS

1/2" PLASTIC LAM.CLAD BACK

3/4" PLASTIC LAM.CLAD ADJUSTABLESHELVING

3/4" PLASTIC LAM.CLAD BOTTOM

SOLID SURFACECOUNTERTOP

PLASTIC LAM. CLADDRAWER W/PULLSHELF BRACKETSBEYOND WITH CLIPS

1/2" PLAS. LAM.CLAD BACK

3/4" PLASTIC LAM.CLAD DOOR W/PULL

3/4" PLASTIC LAM. CLAD BASE

WOOD BLOCKING

7' -

0"

WIREPULL

BASE

WIREPULL2'

- 10

"1'

- 6"

2' -

8"

1 1/

2"

2' - 1"

3/4" PLASTIC LAM. CLADADJUSTABLE SHELVING

SEALANT


WOOD BLOCKING

1 1/

2"

1' - 2"

4"3/4" PLASTICLAM. CLAD TOP

WOOD BLOCKING

SHELF BRACKETSBEYOND WITH CLIPS

1/2" PLASTIC LAM.CLAD BACK

3/4" PLASTIC LAM.CLAD ADJUSTABLESHELVING

3/4" PLASTIC LAM.CLAD BOTTOM

SOLID SURFACECOUNTERTOP

7' -

0"

2' -

10"

1' -

6"2'

- 8"

1/2" PLAS. LAM.CLAD BACK


3/4" PLASTIC LAM.CLAD BASE

WOOD BLOCKING

1/2"

3"

2' - 0"BASE

WIRE PULL

WIREPULL

1 1/

2"

2' - 1"


SEALANT

WOOD BLOCKING

1" DIA. CHROME CLOSETROD WITH "STANLEY"CLOSET BAR BRACKET,CATALOG NO. CD 7089

WOOD BLOCKING

3/4" PLASTIC LAMINATESHELF AND SIDES

5' -

4"

A2.19

8"

1' - 6"

1 1/2"

1 1/

2"

BULLNOSE, PLASTICTRIM, COLOR SELECTEDBY ARCHITECT

5'-0

" A.F

.F.

2" RADIUS1" DIA. CHROME CLOSET RODWITH "STANLEY" CLOSET BARBRACKET, CATALOG NO. CD7089 3/4" PLASTIC LAMINATE

CLAD BACK PANEL(FINISH SIDE)

3/4" PLASTIC LAM. CLADFRAME (FINISH ALLEXPOSED SIDES)

PROVIDE CONT. WOODBLOCKING IN STUD WALL

3/4" PLASTIC LAMINATECLAD SHELF

4"

1 3/

4"

3"3/4"

GENERAL MILLWORK NOTES:PROVIDE AWI "PREMIUM" GRADE MILLWORK.

CABINET DEPTHS ARE FROM FACE OF GYPSUM BOARD TO OUTSIDE FACE OFCABINET DOOR. UNLESS NOTED OTHERWISE.

INSTALL PLASTIC LAMINATE CLAD FILLER AS REQUIRED. FINISH OF THE FILLERSHALL MATCH THE FINISH OF THE ADJACENT MILLWORK UNLESS NOTEDOTHERWISE.

ALL EXPOSED SURFACES OF MILLWORK SHALL RECEIVE PLASTIC LAMINATE.CONTACT ARCHITECT IN CASES OF CONFLICT REGARDING COLOR SELECTION.

1.

2.

3.

4.

HEADERFRAMING

5/8" GYPSUMBOARD

HOLLOWMETAL FRAME

JOINT SEALANT(BOTH SIDES)

METAL STUDS -3 -5/8" AT 16"O.C. UNO

GYPSUM BOARD- 5/8" UNO

HOLLOW METALFRAME

LINE OF INTERSECTINGWALL (TYPICAL WHEREOCCURS)

4" +

/-

DNI

AI AN

No. AR10100128

STATE OF

GER

RTSI EDE

ARCH I T E

CT

JACK

SON R

ICHARDFABER

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

A2.1

DOORS SCHEDULE, INTERIORELEVATIONS, DETAILS

DOOR SCHEDULE

Door NumberDoor Data Frame Data

Hardware Set Comments Door NumberFire Rating Type Material Width Height Thickness Glass Type Material Head Frame Depth Jamb1075 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT1 HM - 5 3/4" - 2 1, 4 10751076 - - 3' - 0" 7' - 0" 1 3/4" - - - - - - - 8 1076

1076-1 B WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT2 HM 1/A2.1 5 3/4" 2/A2.1 2 2 1076-11077 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT3 HM SEE RCP 5 3/4" - 3 1, 2, 4 10771078 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 10781079 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 10791080 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 10801081 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 10811082 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 10821083 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 10831084 A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT5 HM SEE RCP 5 3/4" SEE PLAN 1 1, 2, 4 1084

1085A A WOOD 3' - 0" 7' - 0" 1 3/4" TEMP - - - - - 1 1, 2, 6 1085A1085B C WOOD 3' - 0" 7' - 0" 1 3/4" - - - - - - 1 6 1085B

1086-1A C WOOD 3' - 0" 7' - 0" 1 3/4" - FT2 HM 1/A2.1 5 3/4" 2/A2.1 - 2, 3 1086-1A1086-1B B WOOD 3' - 0" 7' - 0" 1 3/4" TEMP - - - - - 4 3, 6 1086-1B1086-2A C WOOD 3' - 0" 7' - 0" 1 3/4" - FT2 HM 1/A2.1 2/A2.1 2 2, 5 1086-2A1086-2B B WOOD 3' - 0" 7' - 0" 1 3/4" TEMP FT2 HM 1/A2.1 5 3/4" 2/A2.1 4 - 1086-2B

1/4" = 1'-0"DOOR ELEVATIONS

1/4" = 1'-0"HOLLOW METAL FRAME ELEVATIONS

3/8" = 1'-0"3 INTERIOR ELEVATION - ROOM NO. 1077

3/8" = 1'-0"4 INTERIOR ELEVATION - ROOM NO. 1086-1

3/8" = 1'-0"5 INTERIOR ELEVATION - ROOM NO. 1086-2

3/4" = 1'-0"6 CASEWORK SECTION



3" = 1'-0"9 SECTION

3" = 1'-0"1 HEAD DETAIL

3" = 1'-0"2 JAMB DETAIL

# Description Date

5/8" GYPSUM BOARD

3 5/8" 20 GA. METALSTUDS

ALUMINUM FRAME

5/8" GYPSUM BOARD

3 5/8" 20 GA. METALSTUDS

HOLLOW METALFRAME

3/8" TEMP.GLAZING

3/8" TEMP.GLAZING

ALTERNATE #1 BASE BID

ALUMINUM FRAME

3/8" (TYP.) TEMP.GLAZING

HOLLOWMETAL FRAME

3/8" (TYP.) TEMP.GLAZING

BASE BIDALTERNATE #1

HEADERFRAMING

5/8" GYPSUMBOARD

ALUMINUMFRAME

ALERNATE #1

GYPSUM BOARD -5/8" UNO

METAL STUDS -6" AT 16" O.C.

JOINT SEALANT(BOTH SIDES)

HOLLOW METALFRAME

3/8" TEMP. GLAZING(TYP.)BASE BID

HEADERFRAMING

5/8" GYPSUMBOARD

ALUMINUMFRAME

HEADERFRAMING

5/8" GYPSUMBOARD

HOLLOW METALFRAME

BASE BID

3/8" TEMP.GLAZING

ALTERNATE #1

PLAN

SEE

ALUMINUMFRAME

5/8" GYPSUMBOARD

3 5/8" 20 GA.METAL STUDS

1/2" GYPSUMBOARD

.125" ALUMINUMTRIM

ALTERNATE #1

PLAN

SEE

HOLLOWMETAL FRAME

5/8" GYPSUMBOARD

5/8" GYPSUMBOARD

BASE BID3 5/8" 20 GA.METAL STUDS

3/8" TEMP.GLAZING

3/8" TEMP.GLAZING


5/8" GYPSUMBOARD

ALUMINUMFRAME

3 5/8" 20 GA.METAL STUDS5/8" GYPSUMBOARD

HOLLOW METALFRAME

3/8" TEMP.GLAZING

3/8" TEMP.GLAZING


HEADERFRAMING

5/8" GYPSUMBOARD

ALUMINUMFRAME

ALTERNATE #1

HEADERFRAMING

5/8" GYPSUMBOARD

HOLLOWMETAL FRAME

BASE BID

SUSPENDEDACOUSTICALPANELCEILING SYSTEM

HEADERFRAMING

5/8" GYPSUMBOARD

ALUMINUMFRAME

ALTERNATE #1


HEADERFRAMING

HOLLOWMETAL FRAME

BASE BID

5/8" GYPSUMBOARD

PLAN

SEE

ALUMINUMFRAME

5/8" GYPSUMBOARD


1/2" GYPSUMBOARD

.125"ALUMINUMTRIM

ALTERNATE #1

PLAN

SEE

HOLLOWMETAL FRAME

5/8" GYPSUMBOARD

FRAME ANCHOR- MINIMUM 3 PERJAMB

5/8" GYPSUMBOARD

BASE BID


ALUMINUMFRAME

5/8" GYPSUMBOARD


WOODBLOCKING

ALTERNATE #1

HOLLOWMETALFRAME

5/8" GYPSUMBOARD

FRAMEANCHOR -MINIMUM 3PER JAMB

WOODBLOCKING

BASE BID

3/8" TEMP.GLAZING

3/8" TEMP.GLAZING

3/8" TEMP.GLAZING

HOLLOWMETALFRAME

.125"ALUMINUMTRIM

WOODBLOCKING

3 5/8" METALSTUDS

ALUMINUMFRAME


PLAN

SEE

ALUMINUMFRAME

5/8" GYPSUMBOARD


1/2" GYPSUMBOARD

.125"ALUMINUMTRIM

3/8" TEMP.GLAZING

PLAN

SEE

HOLLOWMETAL FRAME

5/8" GYPSUMBOARD

FRAME ANCHOR- MINIMUM 3 PERJAMB

5/8" GYPSUMBOARD


3/8" TEMP.GLAZING

HEADERFRAMING

5/8" GYPSUMBOARD

ALUMINUMFRAME

HEADERFRAMING

5/8" GYPSUMBOARD

HOLLOW METALFRAME

BASE BID

3/8" TEMP.GLAZING

JOINTSEALANT(BOTH SIDES)

JOINTSEALANT(BOTH SIDES)

ALTERNATE #1


HEADERFRAMING

5/8" GYPSUMBOARD

ALUMINUMFRAME


HEADERFRAMING

5/8" GYPSUMBOARD

HOLLOWMETAL FRAME3/8" TEMP. GLAZING

ALERNATE #1 BASE BID

@ DOOR NO.1075


@ DOOR NO.1075



HOLLOWMETAL FRAME

3/8" TEMP.GLAZING (TYP.)

ALUMINUMFRAME

3/8" TEMP.GLAZING (TYP.)

DNI

AI AN

No. AR10100128

STATE OF

GER

RTSI EDE

ARCH I T E

CT

JACK

SON R

ICHARDFABER

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

A2.2

FRAME DETAILS


3" = 1'-0"14 SILL DETAIL












3" = 1'-0"13 DETAIL

# Description Date

WAITING1075

OPEN OFFICE1076

CONFERENCE1077

OFFICE1078

OFFICE1079

OFFICE1080

OFFICE1081

OFFICE1082

OFFICE1083

OFFICE1084

OFFICE1085

BREAK1086-1

STORAGE1086-2

VESTIBULE1087

CORR1074

CORR1076-1

CORR1076-2

WORK1076-3

WC

1

PT3 PT3 PT3 PT3

PT4

PT3

PT3

PT3

PT3

PT3 PT

4

EXIST EXTENTS

NEW

EXIST EXTENTS

NEW

EXIST EXTENTS

NEW

1

1

1

1

1

G.D.

G.D.

G.D.

G.D.

G.D.

G.D.

2

3

3

TILE CARPETING (096813)

TAG: CPT1MFG: MOHAWKSTYLE: HYPER EARTHCOLOR: BLUE SAPPHIRENMBR: 985INSTALL METHOD: MONOLITHICSIZE: 12"x36"

TAG: CPT2MFG: MOHAWKCOLCT: ICONIC EARTHSTYLE: DRIFTED GROUNDCOLOR: CLEAN SLATEINSTALL METHOD: REFER TO DETAILSSIZE: 12"x36"

RESILIENT TILE FLOOR (096519)

TAG: LVP1MFG: PATCRAFTCOLCT: METALLSTYLE: STUDIOCOLOR: TBDNUMBER: TBDSIZE: 12"x24"INSTALLATION METHOD: HERRINGBONE

WALLCOVERING (097200)

TAG: WC1MFG: SOURCE ONECOLCT: WOODSCOLOR: QUARTERED WHITE OAKNMBR: SWS-06

WALL PROTECTION (102600)

TAG: CG1MFG: ACROVYNSERIES: SM-FULL HEIGHT 1/4" RADIUS CORNERSIZE: 3" LEGxFULL WALL HEIGHT (TOP OF BASETO CEILING)COLOR: TBD

RESILIENT BASE AND ACCESSORIES (096513)

TAG: RB1MFG: JOHNSONITESTYLE: MANDALAYCOLOR: TBDSIZE: 4.5"H

INTERIOR PAINTING (099123)

TAG: PT1 (FIELD PAINT & DOOR FRAME)MFG: SHERWIN WILLIAMSCOLOR: TBDNMBR: TBD

TAG: PT2 (ACCENT PAINT)MFG: SHERWIN WILLIAMSCOLOR: TBDNMBR: TBD



TAG: PT5 (CEILING PAINT)MFG: SHERWIN WILLIAMSCOLOR: CEILING BRIGHT WHITENMBR: TBD

FINISH MATERIALS LEGENDPLASTIC LAMINATE (064023)

TAG: PL1MFG: WILSONARTCOLOR: NATURAL RECONNMBR: 7996-38FINISH: FINE VELVET

SOLID SURFACE (064023)

TAG: SS1MFG: WILSONARTCOLOR: YUKON RIVERSTONE

ACOUSTICAL PANEL CEILING (095113)

TAG: APC1MFG: CERTAINTEEDSTYLE: PERFORMA ADAGIOITEM NMBR: 1662F-IFO-1EDGE STYLE: SQUARE TEGULARSIZE: 24"x24"x1 1/2"FINISH: WHITEGRID: ARMSTRONG 9/16" INTERLUDE XL HRCTILE AND GRID COLOR: WHITE

ROLLER WINDOW SHADES (122413)

TAG: RWS1MFG:SERIES:STYLE:COLOR:

HORIZONTAL LOUVER BLINDS (122113)

TAG: HLB1MFG:SERIES:STYLE:COLOR:

CARPET

JOHNSONITE SLIM LINE SLTTRANSITION, COLOR BY ARCHITECT

RESILIENT FLOOR

CARPET TO RESILIENT

DNI

AI AN

No. AR10100128

STATE OF

GER

RTSI EDE

ARCH I T E

CT

JACK

SON R

ICHARDFABER

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

A3.1

FIRST FLOOR FINISH PLANAND SCHEDULE

1/4" = 1'-0"FIRST FLOOR FINISH PLAN

ROOM FINISH SCHEDULE

RoomFloor Finish Base Finish

Wall Finish CeilingFinish Comments NumberNumber Name Wall A Wall B Wall C Wall D

1075 WAITING CPT1, CPT2 RB1 -- -- PT1, WC1 PT1, PT1 APC1, GYP. 10751076 OPEN OFFICE CPT1,CPT2 RB1 -- PT1 PT1, WC1 PT1 APC1, GYP. 1076

1076-1 CORR CPT1, CPT2 RB1 PT1 -- PT1, WC1 PT1 APC1, GYP. 1076-11076-2 CORR CPT1, CPT2 RB1 PT1 PT1 PT1 PT1 APC1 1076-21076-3 WORK CPT1, CPT2 RB1 -- PT1 PT1 PT1 APC1 1076-31077 CONFERENCE CPT2 RB1 PT1 PT3 PT4 PT1 APC1 10771078 OFFICE CPT2 RB1 -- PT3 PT1 PT1 APC1 10781079 OFFICE CPT2 RB1 -- PT3 PT1 PT1 APC1 10791080 OFFICE CPT2 RB1 -- PT3 PT1 PT1 APC1 10801081 OFFICE CPT2 RB1 PT1 PT1 -- PT3 APC1 10811082 OFFICE CPT2 RB1 PT1 PT1 -- PT3 APC1 10821083 OFFICE CPT2 RB1 PT1 PT1 -- PT3 APC1 10831084 OFFICE CPT2 RB1 PT1 PT1 -- PT3 APC1 10841085 OFFICE CPT2 RB1 PT1 PT1 PT1 PT3 APC1 1085

1086-1 BREAK LVP1 RB1 PT1 PT1 PT4 PT1 APC1 1086-11086-2 STORAGE CPT2 RB1 PT1 PT1 PT1 PT1 APC1 1086-2

12" = 1'-0"1 TYPICAL FLOOR TRANSITIONS

FINISH PLAN REFERENCE NOTES1 INSTALL FLOORING IN BLEND [CPT1] (30%), [CPT2] (70%).

ARCHITECT TO PROVIDE FUTURE DETAILS WITH SUBMITTALS.

2 PROVIDE VERTICAL CONTROL JOINTS ON WALL. VERTICALCONTROL JOINTS PAINT TO MATCH [WC1]. CONFIRM PAINTWITH ARCHITECT.

3 RE-INSTALL EXISTING CERAMIC TILE BASE. MATCH EXISTINGGROUT.

GENERAL INTERIOR FINISH NOTESA. ALL INTERIORS NOTES, SCHEDULES AND LEGENDS REFERENCE ABCD LEGEND. REFER TO VIEW HEADER OF ROOM FINISH SCEDULE.

B. PROVIDE RESILIENT OR METAL TRANSITION STRIP AT ALL FLOORING MATERIAL JUNCTURES. WHERE MATERIALS TRANSITION AT DOORSCENTER OF TRANSITION TO BE LOCATED ON CENTER OF DOOR. REFER TO DETAIL [1/A3.1] FOR TYPICAL FLOOR MATERIAL TRANSITIONS.COLOR SELECTED BY ARCHITECT FROM MANUFACTURES FULL RANGE OF COLORS.

C. ALL EXPOSED GYP. CEILINGS AS WELL AS UNDERSIDE AND FACES OF BULKHEADS, AND SOFFITS TO BE PAINTED, REFER TO FINISHSCHEDULE FOR CEILING FINISHES AND REFLECTED CEILING PLANS FOR CEILING MATERIAL EXTENTS AND FINISH REQUIREMENTS.COORDINATE ANY PAINT FINISHES WITH ARCHITECT IN FIELD BEFORE PROCEEDING WITH FINISH WORK.

D. REFER TO DOOR SCHEDULE AND FINISH FLOOR PLAN FOR CLARIFICATION OF DOOR MATERIALS. ALL HOLLOW METAL DOOR FRAMES TOBE PAINTED [PT1].

E. ALL EXPOSED GYP WALLS TO BE PAINTED UNLESS NOTED OTHERWISE.

F. ALL DIFFUSERS TO BE PAINTED TO MATCH ADJACENT WALL FINISH, VERIFY COLOR WITH ARCHITECT IN FIELD.

G. PAINT FINISH SHEEN SCHEDULE: WALLS- EGGSHELL ACRYLIC LATEX; HOLLOW METAL DOORS AND FRAMES- SEMI GLOSS ENAMEL;CEILING FLAT ACRYLIC LATEX UNLESS NOTED OTHERWISE.

I. REFER TO FINISH FLOOR PLANS FOR PAINT ACCENT LOCATIONS AND FLOOR FINISH PATTERNS AND EXTENTS.

J. REFER TO INTERIOR ELEVATIONS FOR CASEWORK FINISH LOCATION.

K. WHERE NEW FINISHES WOULD MATCH EXISTING FINISHES, OR NEW FINISHES ARE NOT REQUIRED, MAINTAIN EXISTING FINISHES WHEREPOSSIBLE DURING DEMOLITION AND CONSTRUCTION PHASE FOR REUSE. PATCH AND MATCH EXISTING FINISHES WHERE DISTURBED BYCONSTRUCTION.

L. PROVIDE WALL PROTECTION 9CORNER GUARDS) WHERE INDICATED ON FLOOR PLANS.

M. CONFIRM ACCENT PAINT LOCATION AND COLOR WITH ARCHITECT IN FIELD BEFORE PROCEEDING WITH FINISH WORK.

N. EXISTING ROOM FINISHES SHALL BE PROTECTED DURING THE CONSTRUCTION. WHERE DAMAGED, THEY SHALL BE PATCHED ANDREPAIRED AS REQUIRED TO MATCH THE SURROUNDING AND/OR EXISTING FINISHES.

O. NEW CONSTRUCTION SHALL BE FINISHED AS REQUIRED TO MATCH THE SURROUNDING EXISTING FINISHES UNLESS NOTED OTHERWISE.PATCH AND REPAIR EXISTING WALLS AS REQUIRED BEFORE THE INSTALLATION OF THE SCHEDULED NEW FINISHES.

# Description Date

5678

F

G

H

K

P1

5678

F

G

H

K

P2

PLUMBING FIXTURE LIST

SK-1 SINK ELKAY LR-1918, 19" x 18" x 7-1/2" DEEP SINGLE COMPARTMENT 18GAUGE STAINLESS STEEL SELF-RIM COUNTER INSERT THREE HOLELEDGE SINK. FURNISH WITH CHICAGO FAUCET 201A WITH L8 SWINGSPOUT, 369 HANDLES, 2.2 GPM AERATOR, ELKAY LK-99 STAINLESS STEELSTRAINER WITH TAILPIECE, CHROME-PLATED P-TRAP WITH CLEANOUTAND ESCUTCHEON, HAND WHEEL STOP WALL SUPPLIES AND RISERS.

RB-1 OATEY 38811 REFRIGERATOR CONNECTION BOX WITH VALVE. COORDINATEMOUNTING HEIGHT WITH EQUIPMENT.

FIXTURE FINAL CONNECTION SCHEDULE

LAVATORY OR SINK

NOTES:1. ALL FINAL CONNECTIONS TO FIXTURES SHALL BE AS INDICATED ABOVE UNLESS SPECIFICALLY SHOWN OTHERWISE ON THE

DRAWINGS.

FIXTURE COLD WATERHOT WATER WASTE

1-1/2"1/2" 1/2"

REMARKSVENT

1-1/2"

5678

F

G

H

K

4"

2"

P3

P7

5678

F

G

H

K

RB-1SK-1

1 1/2" 1/2"

3/4" 3/4"

P4

P5

1 1/2"

P6

2"

1 1/2"

SK-1

4"

1 1/2"

2"

SUBSTITUTIONS SHALL BE MADE ONLY WITH APPROVAL OF ENGINEER.

INDIANA PLUMBING CODEINDIANA MECHANICAL CODEINDIANA BUILDING CODE

CONTRACTOR SHALL MAKE MODIFICATIONS IN THE INSTALLATION SO ALLEQUIPMENT AND MATERIALS FIT PROPERLY AND CAN BE SERVICED.

INDICATE GENERAL ARRANGEMENT OF EQUIPMENT, FIXTURES AND PIPING.THE PLUMBING DRAWINGS ARE DIAGRAMMATIC AND ARE INTENDED TO

OSHA

GENERAL:

PLUMBING SPECIFICATIONS:

MIN. ROD SIZE

TIN ANTIMONY.

PIPE SIZE MAX. SPAN

CONFORMING TO ASTM B 88. FITTINGS SHALL BE WROUGHT COPPER,

3/8"5 FT.1/2" & 3/4"

SUBJECT PIPING SYSTEM TO A HYDROSTATIC PRESSURE TEST OF AT LEAST50 PSIG ABOVE OPERATING PRESSURE FOR 10 MINUTES PRIOR TO INSTALLINGINSULATION. DO NOT EXCEED PRESSURE RATING OF PIPING SYSTEM.

ALL DOMESTIC WATER PIPING SHALL BE COPPER PIPE, TYPE L

ASTM B16.22. JOINING MATERIAL SHALL BE SOLDER, ASTM B 32, 95-5

SANITARY PIPING:

CONTRACTOR SHALL SUBMIT FOUR (4) COPIES OF EQUIPMENT, FIXTURES,TRIM AND MATERIAL INFORMATION TO THE ENGINEER. INCLUDED IN THEINFORMATION SHALL BE PERFORMANCE DATA, RATINGS,WIRINGDIAGRAMS, MAINTENANCE INSTRUCTIONS, AND PARTS LIST.

ALL DOMESTIC WATER VALVES SHALL BE BALL TYPE, 150 PSIG SWP, TWOPIECE, BRONZE BODY, FULL PORT, AND STAINLESS STEEL TRIM.

SUBJECT PIPING SYSTEM TO A HYDROSTATIC PRESSURE TEST OF 10FT. OF WATER.

P.1 ALL WORK SHALL BE DONE IN ACCORDANCE WITH ALL APPLICABLENATIONAL, STATE AND LOCAL CODES AND REGULATIONS INCLUDING, BUTNOT LIMITED TO THE FOLLOWING:

P.2

P.3

P.4

DOMESTIC WATER PIPING:

P.5

P.6

P.7

INSULATION THICKNESSSERVICE PIPE SIZE

COLD WATER 1" AND SMALLER1-1/4" AND LARGER

1/2"1"

HOT WATER ANDRECIRCULATED HOT

1-1/2" AND SMALLER2" AND LARGER

1"1-1/2"

WATER

COPPER WATER PIPING SHALL BE SUPPORTED WITH ADJUSTABLE STEELCLEVIS HANGERS ACCORDING TO THE FOLLOWING:

P.8

P.9

P.10 SANITARY PIPING SHALL BE SOLID WALL PVC SCHEDULE 40 WITHSOLVENT WELDED JOINTS. SLOPE PIPING 1 PERCENT IN DIRECTION OF FLOW.

DOMESTIC WATER PIPING INSULATION SHALL BE MINERAL-FIBER,PREFORMED PIPE, TYPE 1., WITH FACTORY APPLIED ALL SERVICE JACKET.PROVIDE PIPE INSULATION SHIELDS AT EACH PIPE HANGER. INSTALL INACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS ACCORDING TOTHE FOLLOWING:

P.12

P.14 1-1/2" TALL PIPE LABELS SHALL BE COLOR CODED WITH LETTERINGINDICATED SERVICE AND FLOW DIRECTION. PROVIDE PIPE LABELS EVERY 25FEET AND AT VALVES, BRANCHES AND EQUIPMENT. EQUIPMENT LABELSSHALL BE BRASS WITH MINIMUM 1/4" LETTER SIZE. PERMANENTLY FASTENEQUIPMENT LABEL WHERE ACCESSIBLE AND VISIBLE.

ALL INSTALLATIONS SHALL BE SEISMICALLY SECURED.

MISC.

CONTRACTOR SHALL NOTIFY OWNER IN WRITING 3 DAYS IN ADVANCE FORALL UTILITY DISRUPTIONS. CONTRACTOR SHALL COORDINATECONSTRUCTION WITH THE OWNER AND ENGINEER. THE PROJECT SHALL BEPHASED TO MINIMIZE THE DISRUPTION TO THE FACILITIES.

MIN. ROD SIZEPIPE SIZE MAX. SPAN

3/8"4 FT.

P.13 VENT PIPING SHALL BE SUPPORTED WITH ADJUSTABLE STEELCLEVIS HANGERS ACCORDING TO THE FOLLOWING:

1-1/2" & 2"

P.15

P.16

P.11 VENT PIPING SHALL BE CAST IRON OR COPPER.

RELOCATE SPRINKLER HEADS AND PIPING AS REQUIRED FOR NEWINSTALLATIONS. ALL FIRE PROTECTION PIPING WORK / REWORK SHALL BEPERFORMED BY THE PIPING CONTRACTOR.

P.17

INDIANA FIRE CODE NFPA

R

R

ED

A

N

PE10505044

PROF I N

O

E

SSI

LAN

D I

E

NA

STATE OF

No.

EN

GI

RE

R

A

T

GAY E

NWS

TSI

.

RE

NE IH

T

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

03/14/2017

P1.1

PLUMBING PLANS

RWSRWS CSM

2'0' 4' 8'

North

1/8" = 1'-0"

FIRST FLOOR PLUMBING DEMOLITION PLAN

2'0' 4' 8'

North

1/8" = 1'-0"

LOWER LEVEL PLUMBING DEMOLITION PLAN

PLAN NOTES:P1 REMOVE SINK AND ASSOCIATED WATER AND VENT LINES TO WHERE

SHOWN.

P2 REMOVE 2" WASTE UP TO SINK AND TO WHERE SHOWN.

1/8" = 1'-0"

LOWER LEVEL PLUMBING PLAN 1/8" = 1'-0"

FIRST FLOOR PLUMBING PLAN

2'0' 4' 8'

North

2'0' 4' 8'

North

P3 2" WASTE UP TO SINK.

P4 INSTALL CHECK VALVE AND BALANCING VALVE IN EXISTING 3/4"HWR LINE. BALANCE TO 0.5 GPM.

P5 BALANCE 1/2" HWR BALANCING VALVE TO 0.5 GPM.

SANITARY RISER DIAGRAM

P6 REWORK / MODIFY EXISTING SPRINKLER PIPING AND HEADS ASREQUIRED. REFER TO REFLECTED CEILING PLAN FOR TYPES ANDHEIGHTS OF CEILINGS. PROVIDE CONCEALED TYPE HEADSLOCATED IN HARD CEILINGS AND BULKHEADS. SPRINKLERPROJECT AREA LIGHT HAZARD.

P7 REMOVE AND REINSTALL CEILING AS REQUIRED FORINSTALLATION OF PIPING. CONTRACTOR SHALL REPLACE ANYDAMAGED CEILING TILES THAT OCCUR DURING INSTALLATION ATTHEIR EXPENSE.

# Description Date

T

T T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

T

5678

F

G

H

K

16"ø

14"ø

12"ø10"ø

12"x

10"

18"x12"10"ø

6"ø

16"x12"

16"x12"

6"ø

7"ø

8"ø

8"ø

6"ø

12"x12"

10"ø

12"x

12"

30"x18"

12"x

12"

10"ø

8"ø

6"ø

6"ø

16"x12"

16"x12"

16"x12"

10"ø

6"ø

8"ø

10"x10"

12"x10"

12"x12"

10"ø

1077

10781079

1080

1081

1082

1083

1084

1076-2

1076

10751086-2

1086-1

1085

10"ø

10"ø

10"ø

10"ø

10"ø

10"ø

R-1

R-1

S-2220

S-3290

S-3290

S-3210

S-3320

S-3240

R-1S-2220 S-3

230

S-3250

S-3250

R-1

R-1

S-3250

S-3250

S-3250

VAV-1076

12"x

12"

6"ø

R-1R-1

R-1

R-1

10"ø

S-4370

S-4370

12"ø

16"x14"

R-1

R-1

R-1

10"ø

8"ø

8"ø

8"ø

8"ø

VAV-1077B

16"x12"

S-3320

10"ø

S-2230

S-2230

S-2230

R-1

VAV-1086

VAV-1075

VV-1085

VV-1084

VV-1083

VV-1082

VV-1081

VV-1079

VV-1077

12"ø

S-2220

5678

F

G

H

K

M4

M4

M4

M4

M4 M4

M4

M4M4

M3

M4M4

M4

M4

M4M4

M4

M4

M4

M4

10"ø

M4

M4

M4

M4

M4

M4

10"ø

10"ø

10"ø

10"ø

5678

F

G

H

K

VAV-1077BVV-1079

VV-1077

VAV-1076

VAV-1086

VAV-1075

VAV-1075

VAV-1077

VAV-1077B

VAV-1079

VAV-1076

VAV-1086

1075

1076

10771078107910801081

1082

1083

1084

1085 1086-1 1086-2

1076-1

1076-2

1076-3

3/4" 3/4"

1 1/4" 1 1/4"

3/4" 3/4"

M5

M5

M5

M5

M5

M5

M5

M5

5678

F

G

H

K

M2

M3

M2

M1

M1M1

M1

M1

M1

M1

R

R

ED

A

N

PE10505044

PROF I N

O

E

SSI

LAN

D I

E

NA

STATE OF

No.

EN

GI

RE

R

A

T

GAY E

NWS

TSI

.

RE

NE IH

T

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

03/14/2017

M1.1

FIRST FLOOR HVAC PLAN

RWSRWS CSM

2'0' 4' 8'

North

NO SCALE

LOW PRESSURE DUCT LEGEND

TEMPERATURE SENSOR (ALIGN SPACEABOVE LIGHT SWITCH - COORDINATEALL LOCATIONS WITH ARCHITECT)

T

FD

SD

F/S

D

RETURN/EXHAUSTAIR DUCT DOWN

D

R RADIUS TURN, R/D = 1.5

FLAT ON BOTTOMTRANSITION

FLAT ON TOPTRANSITION

WHERE 1.5 R/D RADIUSTURNS ARE NOT ALLOWEDDUE TO INADEQUATE SPACE,PROVIDE A SQUARE ELBOWWITH TURNING VANES

FO

T

FO

B

SQUARE TOROUND TRANSITION

FLEX. INSUL DUCT

CEILING MTD.SUPPLY GRILLE

ROUND DUCT,EXTERNALLY INSULATED

FIRE DAMPER

SMOKE DAMPER

FIRE/SMOKEDAMPER

SIDEWALL DUCTMOUNTED SUPPLYOR RETURN GRILLE

45° BRANCH CONN.W/ VOL DAMPER

RECTANGULAR SUPPLYDUCT #"x#" DUCT SIZEFIRST # = DUCT WIDTHSECOND # = DUCT DEPTH.SIZES SHOWN ARE SHEET METALDIMENSIONS, NO INCREASE INSIZE REQ'D FOR DUCT LINER.

SUPPLY AIRDUCT DOWN

ø ROUND DUCT,EXTERNALLY INSULATED

AIR FLOWDIRECTIONARROW

SUPPLY AIRDUCT UP

RECTANGULAR RETURNDUCT #"x#" DUCT SIZEFIRST # = DUCT WIDTHSECOND # = DUCT DEPTH.SIZES SHOWN ARE SHEET METALDIMENSIONS, NO INCREASE INSIZE REQ'D FOR DUCT LINER.

CEILING MTD. RETURNOR EXHAUST GRILLE

45° BRANCH CONNECTIONW/ VOLUME DAMPER

RETURN/EXHAUSTDUCT UP

GENERAL NOTES:A. ALL CONTROL WIRING SHALL BE BY MECHANICAL CONTRACTOR.

B. ALL THERMOSTATS SHALL BE MOUNTED AT 60" AF.F. UNLESS NOTEDOTHERWISE. WHEN AN ELECTRICAL SWITHC OR OTHER DEVICE ISMOUNTED IN THE SAME LOCATION AS A THEMOSTAT. ALL DEVICESSHALL BE ALIGNED VERTICALLY. VERIFY ALL THERMOSTATLOCATIONS WITH ARCHITCT PRIPR TO INSULATION.

C. ALL RECTANGULAR SUPPLY AND RETURN DUCTWORK SHALL BEINTERNALLY LINED (DUCT DOES NOT NEED TO BE INCREASED FORLINER).

D. ALL ROUND SUPPLY AND ROUND RETURN DUCTWORK SHALL BEEXTERNALLY INSULATED.

E. COORDINATE PIPE ROUTING WITH ALL TRADES. EQUIPMENT SHALLMAINTAIN MANUFACTURER RECOMMENDED CLEARANCES ASREQUIRED.

F. REFERENCE REFLECTED CEILING PLAN FOR TYPES AND HEIGHTS OFCEILINGS.

G. ALL HWS AND HWR PIPING SHALL BE 3/4" UNLESS OTHERWISE NOTED.

H. ALL CONTROL VALVES SHALL BE 2-WAY UNLESS NOTED OTHERWISE.

I. CERTIFIED TEST AND BALANCE CONTRACTOR SHALL BALANCE NEWAND EXISTING DIFFUSERS AND VAV BOXES TO NOTED AIRFLOWS ANDWATER FLOW RATES.

1/8" = 1'-0"

FIRST FLOOR HVAC PLAN

PLAN NOTES:M1 REMOVE AND RELOCATE THERMOSTAT.

1/8" = 1'-0"

FIRST FLOOR HVAC DEMOLITION PLAN

2'0' 4' 8'

North

1/8" = 1'-0"

FIRST FLOOR HVAC PIPING PLAN 1/8" = 1'-0"

FIRST FLOOR HVAC PIPING DEMOLITION PLAN

2'0' 4' 8'

North

2'0' 4' 8'

North

M2 REMOVE TEMPERATURE SENSOR.

M3 REMOVE FAN-POWERED VAV BOX AND ASSOCIATEDDUCTWORK, PIPING AND CONTROLS COMPLETE.

M4 REMOVE DIFFUSER OR GRILLE AND DUCT TO WHERE SHOWN.

M5 RELOCATED THERMOSTAT.

# Description Date

DIFFUSER PANEL

SEAL INSULATION TO EDGEOF DIFFUSER PLENUM

EXTERNALLY 1" INSULATEDDIFFUSER SHELL IN FIELD

INSULATED FLEX DUCT (MAX. 5')

SUPPORT FLEX DUCT WHEN NEEDEDSO INSIDE BEND RADIUS IS MAINTAINED

SEE PLANSFOR SIZE

SINGLE DUCT AIR TERMINAL TEMPERATURECONTROL DIAGRAM AND SEQUENCE OF OPERATION

DPT

TSA.I. - ZONE TEMPERATURE

TE

A.I. - LEAVING AIR TEMPERATURE

THE SINGLE DUCT AIR TERMINAL CONTROLLER SHALL MONITOR ZONE TEMPERATURE, LEAVINGAIR TEMPERATURE, INLET AIR PRESSURE TRANSDUCER, AND ZONE TEMPERATURE SETPOINT

C

H

M

HWR

HWS

A.O. - REHEAT COIL CONTROL VALVEM

A.O. - AIR DAMPER

A.I. - AIRFLOW

EACH CONTROLLER SHALL HAVE A USER DEFINED OCCUPIED/UNOCCUPIED MODE SCHEDULE.OCCUPIED AND UNOCCUPIED MODES SHALL HAVE INDIVIDUAL HEATING AND COOLING ZONETEMPERATURE SETPOINTS.

DURING OCCUPIED MODE, THE CONTROLLER SHALL CALCULATE THE AIRFLOW REQUIRED BASED ON ZONETEMPERATURE, ZONE TEMPERATURE SETPOINT, AND LEAVING AIR TEMPERATURE. THE CONTROLLERSHALL MODULATE THE INLET AIR DAMPER BETWEEN MINIMUM AND MAXIMUM AIRFLOW SETPOINTS TOMAINTAIN THE CALCULATED AIRFLOW BASED ON THE INLET AIR PRESSURE TRANSDUCER. IF ZONETEMPERATURE FALLS BELOW THE ZONE TEMPERATURE SETPOINT, THE CONTROLLER SHALL MODULATETHE INLET AIR DAMPER TO MAINTAIN THE HEATING AIRFLOW SETPOINT AND THE CONTROLLER SHALLMODULATE THE HOT WATER CONTROL VALVE TO MAINTAIN THE ZONE TEMPERATURE SETPOINT. THELEAVING AIR TEMPERATURE SHALL NOT BE ALLOWED TO EXCEED THE LEAVING AIR TEMPERATURE LIMIT.

DURING UNOCCUPIED MODE, THE CONTROLLER SHALL CALCULATE THE AIRFLOW REQUESTEDBASED ON ZONE TEMPERATURE, UNOCCUPIED ZONE TEMPERATURE SETPOINT, AND LEAVING AIRTEMPERATURE. THE CONTROLLER SHALL MODULATE THE INLET AIR DAMPER BETWEEN CLOSEDPOSITION AND MAXIMUM AIRFLOW SETPOINT TO MAINTAIN THE CALCULATED AIRFLOW BASED ONTHE INLET AIR PRESSURE TRANSDUCER. IF TEMPERATURE FALLS BELOW THE UNOCCUPIED ZONETEMPERATURE SETPOINT, THE CONTROLLER SHALL MODULATE THE INLET AIR DAMPER TO MAINTAINTHE HEATING AIRFLOW SETPOINT AND THE CONTROLLER SHALL MODULATE THE HOT WATERCONTROL VALVE TO MAINTAIN THE UNOCCUPIED ZONE TEMPERATURE SETPOINT. THE LEAVING AIRTEMPERATURE SHALL NOT BE ALLOWED TO EXCEED THE LEAVING AIR TEMPERATURE LIMIT.

THE CONTROLLER SHALL PROVIDE ALARMS TO THE FMS AS FOLLOWS :

HIGH ZONE TEMPERATURE/LOW ZONE TEMPERATURE - ALARM AT THE OPERATOR INTERFACE IFZONE TEMPERATURE IS LESS THAN OR GREATER THAN THE COOLING/HEATING ZONE SETPOINT BYAN OPERATOR DEFINED AMOUNT (°F).

HIGH DISCHARGE TEMPERATURE/LOW DISCHARGE TEMPERATURE - ALARM AT THE OPERATORINTERFACE IF TERMINAL LEAVING AIR TEMPERATURE IS ABOVE 95°F (ADJ.) OR BELOW 45°F (ADJ.)

WALLMOUNTED

B.I. - OCCUPANCY OVERRIDE

A.I. - ZONE TEMPERATURE SETPOINT

THIS UNIT SHALL BE CONTROLLED BY A DEDICATED DIGITAL CONTROLLER BY JCI. THE CONTROLLERSHALL BE CONNECTED TO THE EXISTING JCI FMS SYSTEM.

M

COILHOT WATER

UNION (TYP)

P & T PORT (TYP)

HWS

STRAINER W/ BLOWDOWN VALVE AND CAP

SHUTOFF VALVE (TYP)

HWR

2-WAY CONTROL VALVE

MANUAL BALANCE VALVE, TYP.

R-1 TITUS 18"x18" 900 - 0.08 20

24"x24"

GRILLES AND DIFFUSERS SCHEDULE PANEL

SYMBOL

S-1 TITUS

MANUF.

TDCA-AA

TYPE SOUND

LOUVER

SIZE

CORE

TYPE

6"ø

INLET

DIM.

10

THROW

FEET

150

MAX.

CFM

0.10

PRESS.

DROP(IN.)

ALUMINUM

REMARKS

21 LAY-IN

N.C. MOUNTING

24"x24"S-2 TITUS LOUVER 8"ø 13250 0.09 ALUMINUM23

S-3 TITUS 350 16 0.13 24

LAY-IN

LAY-IN

LAY-IN

ALUMINUM

ALUMINUM

TDCA-AA

TDCA-AA

TDCA-AA

24"x24"

24"x24"

LOUVER

LOUVER

10"ø

1. APPLIES TO TERMINAL AIR BOXES WITH ROUND INLETS AND RECTANGULAR OUTLETS.

RECTANGULAR INSULATED DUCT

INSULATED TRANSITION

SLIP AND DRIVE CONNECTION

AIR FLOW

INSULATED FLEX. DUCT

TRIM INSIDE FLEX. DUCT AT THIS POINT

6" MIN.

REHEAT COIL, INSULATEPER SPECIFICATIONS

SECTION OF 26 GA. GALVANIZED SHEETMETAL DUCT. SAME DIAMETER AS FLEX. DUCT

FASTEN WITH SELF-TAPPINGSHEETMETAL SCREWS (MIN. 4)

INSULATED GALVANIZED SHEET METAL DUCT

NYLON TIE WRAP, TWO REQUIREDFOR EACH END OF FLEX. DUCT (TOTAL 4).INSTALL ONE TIE WRAP TO SECURE THEINNER LINER AND ONE TO SECURE THEOUTER SHELL (TYP)

TA

KE

OF

F D

IAM

ET

ER

CU

T D

UC

T O

PE

NIN

GT

O M

AT

CH

LA

RG

ER

PRE-MANUFACTERED CONICALTAKE-OFF WITH SELF-ADHESIVENEOPRENE GASKET (EQUAL TO SHEETMETAL CONNECTORS CONICAL E-Z TAP

NOTES:

R

R

ED

A

N

PE10505044

PROF I N

O

E

SSI

LAN

D I

E

NA

STATE OF

No.

EN

GI

RE

R

A

T

GAY E

NWS

TSI

.

RE

NE IH

T

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

03/14/2017

M2.1

MECHANICAL DETAILS &SCHEDULES

RWSRWS CSM

NOTES:1. THROW DATA FOR SQUARE DIFFUSERS ARE BASED ON 4-WAY THROW, TERMINAL VELOCITY AT 50 FPM.2. PROVIDE APPROPRIATE FRAME AND ALL NECESSARY ACCESSORIES FOR MOUNTING GRILLES IN A HARD CEILING, WHERE REQUIRED.3. 24"x24" LOUVERED CORE DIFFUSERS AND GRILLES W/ ROUND INLETS SHALL ALL HAVE AN 18"x18" BACKPAN SIZE.4. R-1 SHALL HAVE AN INTERNALLY LINED DUCT ELBOW BOOT DIRECTED AWAY FROM OTHER OFFICES OR CORRIDORS.5. TITUS, PRICE, ANEMOSTAT ARE ACCEPTABLE MANUFACTURERS.

M.1

M.2

M.3

M.4

M.5

M.6

M.7

M.8

M.9

DUCTWORK:

SUBSTITUTIONS SHALL BE MADE ONLY WITH APPROVAL OF ENGINEER

INDIANA PLUMBING CODEINDIANA MECHANICAL CODEINDIANA BUILDING CODE

SMACNA HVAC DUCT CONSTRUCTION STANDARDSOSHA

GENERAL:

ELBOWS SHALL BE RADIUS TYPE WITH A (1.5 X WIDTH) CENTERLINE RADIUS OR SQUARE TURNWITH SINGLE THICKNESS TURNING VANES. SEAL INTERIOR DUCTWORK PER SMACNA "HVAC DUCTCONSTRUCTION STANDARDS" 15d, SEAL CLASS "C" FOR LOW PRESSURE. DUCT ABOVE ROOFSHALL BE SEAL CLASS "B".

DUCTWORK SHALL BE GALVANIZED SHEET METAL AS REQUIRED BY SMACNA 2" PRESSURE CLASSFOR LOW PRESSURE.

MECHANICAL SPECIFICATIONS

ROUTE DUCTWORK AS SHOWN ON PLAN; FIELD VERIFY ROUTING, AND CLEARANCES.PREFABRICATE AS MUCH DUCT AS POSSIBLE. ALLOW FOR FIELD TRIM AND ADJUSTMENTS.COORDINATE ANY CONFLICTS WITH ENGINEER PRIOR TO INSTALLATION.

INTERIOR ROUND SUPPLY AIR AND ROUND RETURN AIR DUCTWORK SHALL BE EXTERNALLYWRAPPED WITH 1-1/2" THICK FIBERGLASS INSULATION.

APPLICABLE NFPA STANDARDS

ALL WORK SHALL BE DONE IN ACCORDANCE WITH ALL APPLICABLE NATIONAL, STATE ANDLOCAL CODES AND REGULATIONS INCLUDING BUT NOT LIMITED TO THE FOLLOWING :

M.10 THE SYSTEM SHALL BE BALANCED BY AN INDEPENDENT AABC OR NEBB CERTIFIED BALANCINGCONTRACTOR. THE BALANCING CONTRACTOR SHALL SUBMIT THREE (3) CERTIFIED REPORTSTO THE ENGINEER.

ALL LOW VOLTAGE WIRING SHALL BE BY THE TEMPERATURE CONTROL CONTRACTOR.

COORDINATE DUCTWORK WITH LIGHT FIXTURE SUPPORTS, CONDUIT, PLUMBING, FIREPROTECTION PIPING AND OTHER TRADES.

M.11

ALL INSTALLATIONS SHALL BE SEISMICALLY SECURED.M.12

FIRESTOP ALL FIREWALL AND FLOOR PENETRATIONS.M.13

CONTRACTOR SHALL NOTIFY OWNER IN WRITING 3 DAYS IN ADVANCE FOR ALL UTILITYDISRUPTIONS. CONTRACTOR SHALL COORDINATE CONSTRUCTION WITH THE OWNER ANDENGINEER. THE PROJECT SHALL BE PHASED TO MINIMIZED THE DISRUPTION TO THE FACILITIES.

M.14

THE HVAC DRAWINGS ARE DIAGRAMMATIC AND ARE INTENDED TO INDICATE GENERALARRANGEMENT OF EQUIPMENT, DUCTWORK AND PIPING. CONTRACTOR SHALL MAKEMODIFICATIONS IN THE INSTALLATION SO ALL EQUIPMENT AND MATERIALS FIT PROPERLY ANDCAN BE SERVICED. COORDINATE ALL WORK WITH OTHER TRADES.

CONTRACTOR SHALL SUBMIT FOUR (4) COPIES OF EQUIPMENT AND DIFFUSER INFORMATION TO THEENGINEER. INCLUDED IN THE INFORMATION SHALL BE WIRING DIAGRAMS, MAINTENANCEINSTRUCTIONS, AND PARTS LIST.

NO SCALE

SUPPLY DIFFUSER CONNECTION DETAIL

NO SCALE

AIR TERMINAL AND HOTWATER COIL PIPING DETAIL (2-WAY)

NOTES:1. PROVIDE UNIT WITH:

• 1/2" DUAL DENSITY FIBERGLASS LINER• FACTORY INSTALLED PRESSURE INDEPENDENT DIGITAL CONTROLLER. (SEE SEQUENCE OF OPERATION FOR FURTHER REQUIREMENTS).• ACCESS PANEL• HANGERS• WATER COIL DRAIN AND VENT• CONTROL POWER DISCONNECT

2. CONTRACTOR SHALL FIELD INSULATE HOT WATER COIL CASING WITH 1-1/2" FIBERGLASS DUCT WRAP.3. PERFORMANCE BASED ON 0.75" W.G. PRESSURE AT AIR VALVE INLET.4. JCI, TRANE, AND PRICE ARE ACCEPTABLE MANUFACTURERS.

AIR TERMINAL UNIT SCHEDULE

SYMBOL TYPE

AIR VALVE COIL

UNITDOWNSTREAMSTATIC PRESS.DROP (IN. W.G.) NOTES

DESIGNCOOLINGAIRFLOW

(CFM)

MINIMUMAIRFLOW

(CFM)INTLET

SIZE

DESIGNHEATINGAIRFLOW

(CFM

ENTERINGAIR TEMP.

(°F)

LEAVINGAIR TEMP.

(°F)

ENTERINGWATER

TEMP. (°F)

LEAVINGWATER

TEMP. (°F)

FLOWRATE(GPM)

WATERPRESS.

DROP (FT.W.G.)

COILROWS

VAV-1075 SINGLE DUCTTERMINAL UNIT

450 350 8" 450 55 80 180 146 0.8 0.4 1 0.2 EXISTING


320 80 6" 320 55 95 180 134 0.6 0.1 2 0.2

VAV-1077B SINGLE DUCTTERMINAL UNIT

740 190 10" 480 55 95 180 128 1.0 0.2 2 0.2


240 150 6" 150 55 80 180 143 0.5 0.1 1 0.2 EXISTING

VV-1077 FAN POWERED 625 1250 62 80 180 130 1.0 0.3 1 0.2 EXISTING







1250

690

440

210

210

260

320

8"

6"

6"

6"

6"

6"

6"

NO SCALE

TERMINAL AIR BOX DETAIL

# Description Date

S

a

F1

1,3,5,...

a,b,c,...

WALL MOUNT JUNCTION BOX.

CONNECTION TO ELECTRICAL SYSTEM GROUNDING SYSTEM.

PHASECONDUCTOR

NEUTRAL

GROUND

HOMERUN TO PANEL INDICATED. NUMBER OF ARROWHEADS INDICATESNUMBER OF CIRCUITS. PREFIX INDICATES PANEL NOMENCLATURE.NUMBERS INDICATE CIRCUIT NUMBERS

L1BW-1,3,5

CEILING OUTLET AND LIGHTING FIXTURE AS SCHEDULED.

SYMBOL DESCRIPTIONDESCRIPTIONSYMBOL

WALL OUTLET WITH 20A, 125V DUPLEX RECEPTACLE. MOUNT18 INCHES ABOVE FINISHED FLOOR TO CENTER, UNLESSNOTED OTHERWISE.

WALL OUTLET WITH 20A, 125V DUPLEX RECEPTACLE. MOUNT46 INCHES ABOVE FINISHED FLOOR TO CENTER, OR 8 INCHESABOVE COUNTER OR COUNTER BACKSPLASH TO CENTER,UNLESS NOTED OTHERWISE.

WALL OUTLET WITH 20A, 125V DOUBLE-DUPLEXRECEPTACLE. MOUNT 18 INCHES ABOVE FINISHED FLOOR TOCENTER, UNLESS NOTED OTHERWISE.


CEILING MONT JUNCTION BOX.

NUMBER INDICATES MOUNTING HEIGHT ABOVE FINISHEDFLOOR TO BOTTOM OF OUTLET BOX WHEN SHOWN NEXT TOSYMBOL.

+42"

SYMBOL INDICATES FIXTURE TYPE WHEN SHOWN ON LIGHTINGPLANS ADJACENT TO FIXTURE SYMBOL. REFER TO LIGHTINGFIXTURE SCHEDULE FOR FIXTURE REQUIREMENTS.

CIRCUIT. NUMBER OF CROSSBARS INDICATE QUANTITY OFCONDUCTORS REQUIRED. MINIMUM CONDUIT SIZE SHALL BE3/4 INCH TRADE SIZE. MINIMUM SIZE CONDUCTORS SHALL BE12 AWG.

"GFI"

VOICE/DATA OUTLET. MOUNT OUTLET AT SAME HEIGHT AS THEASSOCIATED POWER OUTLET, UNLESS NOTED OTHERWISE. PROVIDE 1INCH CONDUIT FROM OUTLET BOX TO NEAREST ACCESSIBLE CEILINGCAVITY. BUSH CONDUIT ENDS. PROVIDE TWO DATA CABLES TO OUTLET.OUTLET BOX SHALL BE 4" SQUARE BY 2-3/4" DEEP WITH A SINGLE-GANGPLASTER RING, UNLESS NOTED OTHERWISE. SEE "TYPICAL VOICE/DATACONDUIT INSTALLATION DETAIL", "TYPICAL VOICE/DATA AND POWEROUTLET DETAIL" , AND "INFORMATION OUTLET FACEPLATECONFIGURATION", THIS SHEET, FOR ADDITIONAL REQUIREMENTS.

DESCRIPTIONSYMBOL

OUTLET BOX AND 20A, SINGLE POLE SWITCH. MOUNT AT 46 INCHESABOVE FINISHED FLOOR TO CENTER, UNLESS NOTED OTHERWISE.LOCATE WITHIN 12" OF STRIKE SIDE OF DOOR, UNLESS NOTEDOTHERWISE. LOWER CASE LETTER INDICATES CIRCUIT SWITCHED.

SYMBOL INDICATES GROUND FAULT INTERRUPTER TYPERECEPTACLE WHEN SHOWN PLANS ADJACENT TO SYMBOL.

NUMBERS INDICATE CIRCUIT NUMBERS WHEN SHOWN NEXTTO OR WITHIN SYMBOL ON PLANS.

WALL OUTLET WITH 20A, 125V DOUBLE-DUPLEXRECEPTACLE. MOUNT 46 INCHES ABOVE FINISHED FLOOR TOCENTER, OR 8 INCHES ABOVE COUNTER OR COUNTERBACKSPLASH TO CENTER, UNLESS NOTED OTHERWISE.

OCCUPANCY SENSOR (RATED FOR USE IN LOCATION SHOWN).


LOWER CASE LETTERS INDICATE SWITCHING ARRANGEMENTWHEN SHOWN NEXT TO OR WITHIN SYMBOL ON PLANS.


a

ELECTRICAL LEGEND - POWERELECTRICAL LEGEND - LIGHTING ELECTRICAL LEGEND - SYSTEMS & TECHNOLOGY

TELECOMMUNICATIONS

J

J


DESCRIPTIONSYMBOL

FIRE ALARM SYSTEM

AUDIO-VISUAL ALARM DEVICE. FIRE ALARM SYSTEM. WALLMOUNT AT 80 INCHES A.F.F. TO CENTER OF VISUAL ALARMDEVICE, OR 6 INCHES BELOW CEILING TO TOP, WHICHEVER ISLOWER.

NL SYMBOL INDICATES NIGHT LIGHTING CIRCUIT WHEN SHOWNON LIGHTING PLANS ADJECENT TO FIXTURE.

HALF-HATCHING PATTERN SHOWN WITHIN LIGHTING FIXTURE SYMBOLINDICATES LIGHTING FIXTURE CONNECTED TO EMERGENCY POWERCIRCUIT AND NIGHT LIGHTING.

WALL OUTLET WITH 20A, 125V DUPLEX AND TWO USBACCESS PORTS. MOUNT 18" ABOVE FINISHED FLOOR TOCENTER, UNLESS NOTED OTHERWISE.

DESCRIPTIONSYMBOL

1" CONDUIT ROUTEDWITHIN WALL.

FINISHED FLOOR

OUTLET BOX AS SPECIFIED AND NOTED.

ACCESSIBLECEILING CAVITY

EXTEND CONDUIT PASTCEILING AND PROVIDE A 90°BEND IN CONDUIT. BUSHCONDUIT ENDS. EXTEND TONEAREST ACCESSIBLECEILING CAVITY.

PROVIDE A 4'SERVICE LOOPAT OUTLET BOXAND WITHIN THECOMM ROOMEQUIP RACK.

OUTLET BOX.

POWER, VOICE/DATA, ANDVIDEO OUTLET BOXES SHALLBE NEATLY GROUPEDTOGETHER AT THE SAMEMOUNTING HEIGHTS.(TYPICAL, ALL LOCATIONS).

VOICE/DATA RECEPTACLE

NOTE: COORDINATE EXACT OUTLET BOX INSTALLATIONLOCATIONS IN FIELD WITH ARCHITECT PRIOR TO ROUGH-IN.

NON-ACCESSIBLECEILING CAVITYOR AREA OF EXPOSEDBLDG STRUCTURE

TO PATCHPANEL INCOMM RM

NOTE: IN AREAS WITH EXPOSEDBLDG STRUCTURE ALONG ROOMWALLS (I.E. "FLOATING CEILINGS"),EXTEND CONDUIT TO A POINT ABOVE(AND PAST THE EDGE OF THEFLOATING CEILING) THE ACCESSIBLECEILING CAVITY AS REQUIRED TOPREVENT SEEING LOW VOLTAGECABLING FROM BELOW.

4"

MAX.

DETAIL - TYPICAL VOICE, DATA & POWER OUTLET INSTALLATIONNO SCALE

DETAIL - TYPICAL VOICE, DATA, & INSTRUCTIONAL TECHNOLOGYCONDUIT & CABLE INSTALLATION (WALL BOX LOCATIONS)NO SCALE

GENERAL REQUIREMENTS FOR STRUCTUREDVOICE & DATA CABLING SYSTEMS

CEILING OUTLET AND EXIT LIGHT FIXTURE AS SCHEDULED.ARROWS INDICATE DIRECTION ARROWS REQUIRED

F



WIRELESS NETWORK ACCESS SYSTEM OUTLET.

S3

S4

OUTLET BOX AND 20A, THREE-WAY SWITCH. MOUNT AT 46 INCHESABOVE FINISHED FLOOR TO CENTER, UNLESS NOTED OTHERWISE.LOCATE WITHIN 12" OF STRIKE SIDE OF DOOR, UNLESS NOTEDOTHERWISE. LOWER CASE LETTER INDICATES CIRCUIT SWITCHED.

OUTLET BOX AND 20A, FOUR-WAY SWITCH. MOUNT AT 46 INCHESABOVE FINISHED FLOOR TO CENTER, UNLESS NOTED OTHERWISE.LOCATE WITHIN 12" OF STRIKE SIDE OF DOOR, UNLESS NOTEDOTHERWISE. LOWER CASE LETTER INDICATES CIRCUIT SWITCHED.

a

a

OUTLET BOX AND 20A, DIMMING SWITCH. MOUNT AT 46 INCHESABOVE FINISHED FLOOR TO CENTER, UNLESS NOTED OTHERWISE.LOCATE WITHIN 12" OF STRIKE SIDE OF DOOR, UNLESS NOTEDOTHERWISE. LOWER CASE LETTER INDICATES CIRCUIT SWITCHED.

a

30

28

29

27

2625

24

22

23

21

2019

18

16 20A

17

15

14 20A13

SPACE

SPACE

12 20A

10 20A

20A 11

20A 9

8 20A20A 7 VAV BOXES

6 20A

4 20A

20A 5

20A 3

2 20A20A 1 LTG, REGISTRAR

125A

RECEPTION TRACK LIGHTS

42 20A20A 41

40 20A

38 20A

20A 39

20A 37

36 20A

34 20A

20A 35

20A 33

32 20A20A 31

30 20A

28 20A

20A 29

20A 27

26 20A20A 25

24 20A

22 20A

20A 23

20A 21

20 20A20A 19

18 20A

16 20A

20A 17

20A 15

14 20A20A 13

12 20A

10 20A

20A 11

20A 9

8 20A20A 7

6 20A

4 20A

20A 5

20A 3

2 20A20A 1

100A

225A, 480Y/277V, 3PH, 4WSURFACE MOUNT42 SPACE18,000 A.I.C.PROVIDE WITH HINGED COVER ENCLOSURE*PROVIDE A TYPED INDEX CARD

EXISTING PANEL "H1W"225A, 208Y/120V, 3PH, 4WSURFACE MOUNT42 SPACE10,000 A.I.C.*PROVIDE A TYPED INDEX CARD

EXISTING PANEL "L1BW"

42 20A20A 41

40 20A

38 20A

20A 39

20A 37

36 20A

34 20A

20A 35

20A 33

32 20A20A 31

SPACE30 20A

28 20A

20A 29

20A 27

26 20A20A 25

24 20A

22 20A

20A 23

20A 21

20 20A20A 19

RECEPTS, 1108, 1109, 1112

18 20A

16 20A

20A 17

20A 15

14 20A20A 13

12 20A

10 20A

20A 11

20A 9

8 20A20A 7 RECEPTS, 1091, CORRIDOR

6 20A

4 20A

20A 5

20A 3

2 20A20A 1 T/P POLES 1108

100A

SPACE

RECEPTS, 1108, 1109, 1112

RECEPTS, 1108

225A, 208Y/120V, 3PH, 4WSURFACE MOUNT42 SPACE10,000 A.I.C.*PANEL IS FOR REFERENCE ONLY

EXISTING PANEL "L1AW"

T/P POLES 1108

T/P POLES (FUTURE)1108

RECEPTS, 1110, 1111

T/P POLES (FUTURE), 1110

RECEPTACLES

RECEPTACLES

RECEPTACLES

RECEPTACLES

RECEPTACLES

RECEPTACLES

RECEPTACLES

RECEPTACLES

RECEPTS, 1092, 1111

RECEPTS, 1074, 1093

RECEPTS, 1094, 1110

RECEPTS, 1095, CORRIDOR

RECEPTS, 1096, 1110

RECEPTS, 1108

RECEPTS, 1089

EXISTING LOAD

EXISTING LOAD

LTG, RMS 1096, CORRIDOR

LTG, RM 1070, MICROWAVE

RECEPTS, RMS 1076, 1076-1

RECEPTS, RM 1085

RECEPT, RM 1086-1(COFFEE MAKER)

RECEPTS, RM 1086-2

RECEPTS, RMS 1071, 1072, CORRIDOR

RECEPTS, RM 1075

TEMP CONTROL PANEL, RM 1112

MAINTENANCE

RECEPTS, RMS 1072, 1070

RECEPTS, RM 1076-2

RECEPTS, RM 1077

RECEPTS, RM 1081

RECEPTS, RM 1082

RECEPTS, RM 1076(SYSTEM FURNITURE)

WEST CORRIDOR, AOA

SPACE

RECEPTS, RM 1084

RECEPT, RM 1086-2(COPIER,FAX,PRINTER)

RECEPTS, RM 1083

SPARE

SPARE

SPARE

SPARE

VAV BOXES HONORS AREA

LTG, REGISTRAR

LTG, 1060,1061,1060A,1064,1065,1071,1071A,1072,1070LTG, 1096-1099 & 1103-1107

LTG, CORRIDOR

41

39

37

36

34

35

33

3231

90ATRANSFORMER "XF1W"

LTG, 1091-1095 & 1111

LTG, 1108, 1099 & 1112

VAV BOXES HONORS AREA

RECEPTACLES

STAIR GATE HOLD



RECEPTS, RM 1072

RECEPTS, RMS 1079, 1080

RECEPT, RM 1086-1(REFRIGERATOR)

RECEPT, RM 1086-1(MICROWAVE)

RECEPTS, RM 1086-1

NOTE 1

NOTE 2

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1 NOTE 1

NOTE 1

RECEPTS, RM 1078

RECEPTS, RM 1076-2

RECEPTS, RM 1076

CONDUIT RACEWAY

FINISHED CEILING

SUPPORT CONDUIT VIAADJUSTABLE BAR TYPEHANGER DEVICES ORDIRECTLY TO METALSTUDS USING CONDUIT STRAPS.

OUTLET BOX SECUREDTO METAL STUDSUSINGSIDE MOUNT DEVICE.

PROVIDE WITHMETALLICGYPBOARD STANDOFFSUPPORT AS REQUIREDTO KEEP OUTLET BOXFROM MOVING IN & OUT.

METAL STUD.CONDUIT RACEWAY

FINISHED CEILING

SUPPORT CONDUIT VIAADJUSTABLE BAR TYPEHANGER DEVICES ORDIRECTLY TO METALSTUDS USING CONDUIT STRAPS.

OUTLET BOX.SUPPORTOUTLET BOX TO METALSTUDS USINGADJUSTABLE BAR TYPEHANGER DEVICE. ADJUSTABLE

BARHANGER

METAL STUD

DETAIL - TYPICAL OUTLET BOX SUPPORT DETAIL #1NO SCALE

DETAIL - TYPICAL OUTLET BOX SUPPORT DETAIL#2 (TO BE USED WHEN INSTALLATION AS SHOWN INOUTLET BOX SUPPORT DETAIL #1 IS NOT POSSIBLE)NO SCALE

A

M

R

ED

N

D

STATE OF

PE60900441

OF I

SS

E

OI

N

R

M

P

E

NLA

I A

E

N A N

GI

ER

AN

W

T

HT EGE

. BEIST

J

R

R CKO

NO.

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

03/14/2017

E1.1

ELECTRICAL LEGEND ANDBUSSING DIAGRAM

CWWCWW CWW

BUSSING DIAGRAM

BUSSING NOTES:1. UTILIZE EXISTING CIRCUIT BREAKER MADE SPARE BY DEMOLITION.

2. UTILIZE EXISTING SPARE CIRCUIT BREAKER.

# Description Date

J J J

JJ J

J

JTV

J

F

F

F

F

F

F

F

J

JJ

J

J

J

J

J

S

SS S S

S

S

S

S

SS

S

J

S

SS

SS

S

OFFICE1085

BREAK1086-1

STORAGE1086-2

WAITING1075

CORR1076-1

OPEN OFFICE1076

CORR1076-2

OFFICE1084

OFFICE1083

OFFICE1082

OFFICE1081

OFFICE1080

OFFICE1079

OFFICE1078

CONFERENCE1077

GFI GFI GFI

NOTE 7 NOTE 8 NOTE 9

L1BW-13L1BW-15 L1BW-11EX

EXEX

EX

EX

EX

EX

NOTES 4 & 5 NOTES 4 & 5NOTES 4 & 5

NOTE 6

NOTE 11

NOTE 10

EX

L1BW-34

L1BW-32

L1BW-27

L1BW-30

L1BW-37

L1BW-28L1BW-26L1BW-24

L1BW-40

L1BW-25

L1BW-36L1BW-17

EX

EX

EX

L1BW-5

L1BW-39

L1BW-33

L1BW-31

EX

NOTE 12

EX

L1BW-21

L1BW-19

NOTE 12

NOTE 13,TYPICAL OF 6

NOTE 10

24 24 24 24 26 2826 26 26 28 28 28a

aabbccbc

NOTE 1

NOTE 2

NOTE 1

NOTE 1

NOTE 3

NOTE 3NOTE 3

NOTE 3

NOTE 3

GENERAL DEMOLITION NOTES FORENTIRE PROJECT:D1. THE CONTRACTOR SHALL BE RESPONSIBLE FOR VISITING THE BUILDINGAND SITE TO BECOME FAMILIAR WITH THE EXISTING CONDITIONS. THESEREMOVAL DRAWINGS SHALL SERVE TO AID THE CONTRACTOR IN HISEVALUATION OF THE EXTENT OF REMOVALS, BUT SHALL NOT BE HELD TO BEALL INCLUSIVE.

D2. FOR FURTHER INFORMATION WITH REGARD TO EXTENT OF REMOVALS,SEE THE CONSTRUCTION PLANS WHICH ILLUSTRATE THE ADJACENT NEWCONSTRUCTION.

D3. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL REMOVALSREQUIRED FOR THE INSTALLATION OF NEW WORK, WHETHER OR NOT IT ISSPECIFICALLY INDICATED OR NOTED IN THESE DOCUMENTS.

D4. ALL EQUIPMENT REMOVED FOR RELOCATION SHALL BE REMOVED INSUCH A MANNER THAT REUSE IS POSSIBLE.

D5. ALL CONDUIT RUNS TO REMOVED EQUIPMENT SHALL HAVE ALLCONDUCTORS REMOVED, UNLESS CONDUCTORS ARE REQUIRED TO SERVEEXISTING EQUIPMENT TO REMAIN.

D6. REMOVAL OF EMPTY CONDUIT SHALL BE REQUIRED ONLY IF SUCHCONDUIT INTERFERES WITH THE NEW CONSTRUCTION AND/OR IF INDICATEDTO BE DISCONNECT AND REMOVED COMPLETE BACK TO SOURCE OF FEED.

D7. IF PORTIONS OF CIRCUITS SERVING EQUIPMENT TO REMAIN MUST BERELOCATED OR REMOVED DUE TO OTHER DEMOLITION OR DUE TOINTERFERENCE WITH NEW EQUIPMENT INSTALLATION, THE CIRCUITS SHALLBE MODIFIED IN A MANNER WHICH SHALL ENSURE PROPER OPERATION OFTHE EQUIPMENT AFTER THE CONSTRUCTION IS COMPLETE. CONTRACTORSHALL USE THE SAME GAUGE AND TYPE OF CONDUCTOR, AND THE SAMECONDUIT SIZE AS EXISTING TO MAKE ALL REQUIRED CIRCUIT MODIFICATIONS.

D8. IF WALLS, CEILINGS, FLOORS, OR EQUIPMENT ARE REMOVED, OROTHER DEMOLITION OCCURS, WHICH EXPOSES CIRCUITS SERVINGEQUIPMENT TO REMAIN, THE CIRCUITS SHALL BE RELOCATED OR MODIFIEDIN SUCH A MANNER WHICH SHALL ENSURE THE CONTINUED OPERATION OFTHE CIRCUIT. EXISTING CONDUITS EXPOSED DURING DEMOLITION WHICHREMAIN TO SERVE EQUIPMENT SHALL BE RESUPPORTED IN ACCORDANCEWITH THE REQUIREMENTS OF THE NEC.

D9. EQUIPMENT REMOVED FOR RELOCATION BUT NOT RELOCATED SHALLBE STORED AT A LOCATION DIRECTED BY THE OWNER.

D10. THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE PROPERDISPOSAL OF ALL EQUIPMENT REMOVED.

D11. OWNER RESERVES THE FIRST RIGHT OF REFUSAL OF REMOVEDEQUIPMENT.

D12. THE CONTRACTOR SHALL COORDINATE DISRUPTION OF SERVICESWITH THE OWNER. DISRUPTIONS OF SERVICES SHALL BE KEPT TO AMINIMUM. DISRUPTIONS SHALL ONLY OCCUR AFTER RECEIVING OWNERPRIOR APPROVAL.

D13. THE CONTRACTOR SHALL REFER TO THE MECHANICAL, PLUMBING,AND ARCHITECTURAL PLANS FOR ADDITIONAL REQUIREMENTS ONEQUIPMENT AND AREAS REQUIRING REMOVALS.

ELEC1089 EXISTING PANEL "L1BW"

EXISTING PANEL "L1AW"

EXISTING PANEL "H1W"

1059COMMUNICATIONS

APPROXIMATE BASEMENTLOCATION OF EXISTINGPANEL "EHB"

1/4" = 1'-0"FIRST FLOOR POWER AND SYSTEMS PLAN

A

M

R

ED

N

D

STATE OF

PE60900441

OF I

SS

E

OI

N

R

M

P

E

NLA

I A

E

N A N

GI

ER

AN

W

T

HT EGE

. BEIST

J

R

R CKO

NO.

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

03/14/2017

E2.1

FIRST FLOOR ELECTRICALDEMOLITION, POWER AND

SYSTEMS PLAN

CWWCWW CWW

1/4" = 1'-0"FIRST FLOOR ELECTRICAL DEMOLITION PLAN

2'0' 4' 8'

North

2'0' 4' 8'

North

NOTES:1. UNLESS NOTED OTHERWISE, DISCONNECT AND REMOVE ALL ELECTRICAL DEVICES, FIREALARM DEVICES, COMMUNICATION DEVICES, DATA DEVICES, AND LIGHTING AND ASSOCIATEDDEVICES WITHIN THIS AREA AS REQUIRED FOR DEMOLITION AND NEW CONSTRUCTION.

2. DISCONNECT AND REMOVE ALL LIGHTING FIXTURES AND ASSOCIATED DEVICES WITHIN THISAREA. BRANCH CIRCUITS SHALL REMAIN FOR REUSE.

3. DATA OUTLET TO REMAIN. ELECTRICAL CONTRACTOR SHALL PROVIDE ALL LABOR ANDMATERIAL TO PROTECT CABLE AND OUTLET DURING DEMOLITION AND REWORK OUTLET ASNEEDED FOR NEW CONSTRUCTION. DATA OUTLET SHALL WORK AS BEFORE DEMOLITION.

4. JUNCTION BOX FOR POWER CONNECTION TO SYSTEM FURNITURE. COORDINATE WITHFURNITURE PROVIDER AND OWNER FOR EXACT LOCATION AND MOUNTING HEIGHT PRIOR TOROUGH-IN. PROVIDE FINAL CONNECTIONS PER MANUFACTURER'S REQUIREMENTS.

5. PROVIDE A LOW VOLTAGE RING FOR LOW VOLTAGE CABLE TO SYSTEM FURNITURE. PROVIDEA 2" CONDUIT FROM THE TOP OF THE LOW VOLTAGE RING TO ACCESSIBLE CEILING AND BUSHCONDUT ENDS. COORDINATE WITH FURNITURE PROVIDER AND OWNER FOR EXACT LOCATIONAND MOUNTING HEIGHT PRIOR TO ROUGH-IN. PROVIDE FINAL CONNECTIONS PERMANUFACTURER'S REQUIREMENTS.

6. DEDICATED BRANCH CIRCUIT AND RECEPTACLE FOR COPIER/FAX/PRINTER MACHINE.

7. DEDICATED BRANCH CIRCUIT AND RECEPTACLE FOR MICROWAVE.

8. DEDICATED BRANCH CIRCUIT AND RECEPTACLE FOR COFFEE MAKER.

9. DEDICATED BRANCH CIRCUIT AND RECEPTACLE FOR REFRIGERATOR.

10. PROVIDE LOW VOLTAGE RING FOR LOW VOLTAGE CABLE OUTLET FOR OWNER FURNISHEDAND INSTALLED HDMI CABLE. PROVIDE A QUANTITY OF ONE 1-1/2" CONDUIT FROM THE TOP OFTHE LOW VOLTAGE RING TO ACCESSIBLE CEILING AND BUSH CONDUIT ENDS. PROVIDE A PULLSTRING IN CONDUIT. COORDINATE EXACT LOCATION AND MOUNTING HEIGHT WITH OWNER PRIORTO ROUGH-IN. PROVIDE A SINGLE GANG MOUNTING PLATE WITH STAINLESS STEEL LOWVOLTAGE CABLE ACCESS RING.

11. CONFERNECE TELEVISION LOCATION. PROVIDE ONE RECEPTACLE OUTLET FOR POWER,ONE OUTLET FOR COAX CABLE, ONE OUTLET FOR DATA, AND ONE JUNCTION BOX FOR HDMIOUTLET. MOUNT BANK OF OUTLETS AT 84" ABOVE FINISHED FLOOR TO CENTER.

12. COORDINATE WITH ARCHITECT AND OWNER FOR EXACT INSTALLATION LOCATION ANDMOUNTING HEIGHT PRIOR TO ROUGH-IN.

13. RECEPTACLE AND DATA OUTLET LOCATIONS BUILT INTO BOTTOM OF SYSTEM FURNITURE.REFER TO MANUFACTURER FOR ADDITIONAL REQUIREMENTS.

1/16" = 1'-0"ELECTRICAL AND COMMUNICATION ROOM LOCATIONS

4'0' 8' 16'

North

GENERAL POWER AND SYSTEMS NOTESFOR ENTIRE PROJECT:A. SEE PROJECT SPECIFICATIONS, DIVISION 27, SECTION 271310, FOR ADDITIONALREQUIREMENTS REGARDING QUANTITY AND TYPES OF CABLES ROUTED TO WORK AREAOUTLETS.

B. ALL RECEPTACLES AND SWITCHES IN PROJECT WORK AREA SHALL BE IVORY IN COLOR WITHSTAINLESS STEEL COVER PLATES.

# Description Date

S

S

S

S

S

S

S

S

S

S

S

S

S

F5F

F3

F3 F3

F3F3

F3

F1F1F1

F1

F1F2

F1

F1

F1 F1

F2

F2

F1F1

F1 F1F1 F1

F1F1F1F1

F1

F1

F1

F1

F1

F1

F1F1F1F1F1

F3

F2

F4F4F4F4F4 F4

3a

3a

4a

3b

3b

cd

e

e e

c

d d d

b

a

a

aa

a a

b b b b

f

f

f

3

3 3

3

OPEN OFFICE1076

CORR1076-1

STORAGE1086-2

WAITING1075

BREAK1086-1

OFFICE1085

OFFICE1084

OFFICE1083

OFFICE1082

OFFICE1081

WORK1076-3

CORR1076-2

OFFICE1080

OFFICE1079

OFFICE1078

CONFERENCE1077

3f

H1W-2

H1W-4

3

3

g

g g g gg g

NL

NL

NL

NL NL

NLNLNL

NL

F5A F5AF5CF5AF5DF5A

F5

F3 F3

F3

EX1R

EX1

EX1L

EX1

F5E

F5

F5EF5F5E

F5

F5Ef

f

fff

f

ff

NOTE 1. TYPICAL, ALL NIGHTAND EXIT LIGHTING FIXTURES

NOTE 2

NOTE 2

NOTE 2

NOTE 2 NOTE 2 NOTE 2 NOTE 2

NOTE 2

NOTE 2

NOTE 2

NL

EX1

F3

F4

F5

F5A

F1

RECESSED --- ---120/277(MULTI-VOLT)

6" DIAMETER APERTURE, MEDIUMDISTRIBUTION OPEN DOWNLIGHT,RECESSED DOWNLIGHT, WITH A MAXIMUMFIXTURE DEPTH OF 8". NOMINAL 2000LUMENS OUTPUT. DIMMABLE USING 0 TO10V DIMMING CONTROLS. ACCESSIBLEFROM BELOW A HARD CEILING.

PATHWAY 6VLED2000 SERIES

LEDS 4000K(50,000 HRSWITH 70%

LUMENMAINTENANCE)

QNTYAS

REQUIRED

25W(FIXTURE

INPUTWATTS)

LITHONIA

RECESSED --- ---2'x4' LED RECESSED INDIRECT FIXTUREWITH SOFT INDIRECT LIGHTING. NOMINAL4000 LUMENS OUTPUT, DIMMABLE USING 0TO 10V DIMMING CONTROLS. LIGHT FIXTUREHAS A MAXIMUM DEPTH OF 5".

120/277(MULTI-VOLT)

OM6LED-2000 SERIESPHILIPS OMEGA LTG

2BZL SERIES LEDS 4000K(60,000 HRSWITH 90%

LUMENMAINTENANCE)

QNTYAS

REQUIRED39W ---

---

COOPER __ SERIES

PORTFOLIO LD620D010-ERM SERIES

MANUFACTURER SYMBOL DESCRIPTIONLOUVER FINISH

LIGHTING FIXTURE SCHEDULE

TYPEFIXTURE SERIES

LAMP

LENS WATTS REFLECTOR MOUNTINGBALLAST

LIGHT CONTROLREMARKSFIXTURE

VOLTAGEQNTY PERFIXTURE

FOCAL POINT SKYDOME24" DIAMETER LED FIXTURE MADE WITHEXTRUDED ALUMINUM. 2000 LUMENSOUTPUT, DIMMABLE USING 0 TO 10VDIMMING CONTROLS. ACCESSIBLE FROMBELOW A HARD CEILING.

SAME AS FIXTURE "F5", 4' LENGTH.

2' LENGTH WITH 2" WIDTH RECESSED LEDGEOMETRIC LIGHTING FIXTURE SYSTEM CAPABLEOF MULTIPLE DESIGNS WITH ILLUMINATEDCORNERS AND HAIRLINE JOINTS AND A MAXIMUMDEPTH OF 5.5". 400 LUMEN/FOOT OUTPUT,DIMMABLE USING 0 TO 10V DIMMING CONTROLS.

LEDS 4000K(100,000 HRS

WITH 90%LUMEN

MAINTENANCE)


LUMENMAINTENANCE)

QNTYAS

REQUIRED

QNTYAS

REQUIRED

43W

4.4W/FT.

120/277(MULTI-VOLT)

120/277(MULTI-VOLT)

AXIS LIGHTING SCULPT RECESSED

LITHONIA LDN6 SERIES

NOTE 1

LIGHTING FIXTURE NOTES:1. PROVIDE FIXTURE WITH SLIDE-TO-OFF TYPE, O-TO-10V DIMMING CONTROLLER(S) [QUANTITY ASINDICATED ON THE LIGHTING PLAN]. FULLY COMPATIBLE WITH THE FIXTURE AND RATED FOROPERATION WITH THE FIXTURE AND CONNECTED LOAD. FINISH COLOR OF THE DIMMINGCONTROLLERS AND DEVICE PLATES SHALL MATCH THE COLOR OF ALL OTHER WIRINGDEVICES/DEVICE PLATES CONNECTED TO THE ASSOCIATED POWER SOURCE.

2. FIXTURE FINISH SHALL BE SELECTED DURING SHOP DRAWING SUBMITTAL /REVIEW PROCESS.

3. COORDINATE LETTER COLOR REQUIREMENTS WITH THE OWNER'S STANDARDS FOR EXITLIGHTING FIXTURES.

4. PROVIDE FIXTURE WITH DIRECTION ARROWS WHERE INDICATED ON LIGHTING PLANS.

NOTE 1

NOTES 1 & 2

NOTE 1RECESSED

SURFACEMOUNT

MARK LIGHTING SLOT 2 LED

F2


LUMENMAINTENANCE)

QNTYAS

REQUIRED30W

120/277(MULTI-VOLT)

NOTE 1RECESSED

LITHONIA2'x2' LED RECESSED INDIRECT FIXTUREWITH SOFT INDIRECT LIGHTING. NOMINAL3000 LUMENS OUTPUT, DIMMABLE USING 0TO 10V DIMMING CONTROLS. LIGHTFIXTURE HAS A MAXIMUM DEPTH OF 5".

2BZL SERIES

COOPER __ SERIES

F5C SAME AS FIXTURE "F5", 10' LENGTH.

F5D SAME AS FIXTURE "F5", 14' LENGTH.

F5E SAME AS FIXTURE "F5", 2' X 2' CORNER DESIGN.

EX1 LED (RED)

LITHONIA

SURE-LITES LPX SERIES

MCPHILBEN CXX SERIES ------ ------ASREQ'D

QUANTUM SERIES

CEILING

LED (RED) ------ ------CEILING

------LED (RED) ------CEILINGEX1R

EX1L

120/277(MULTI-VOLT)

120/277(MULTI-VOLT)

120/277(MULTI-VOLT)

LITHONIA


MCPHILBEN CXX SERIES

QUANTUM SERIES

LITHONIA


MCPHILBEN CXX SERIES

QUANTUM SERIES

EXIT LIGHTING FIXTURE, SINGLE-FACE,WHITE THERMOPLASTIC HOUSING WITHGREEN LETTERS.

ASREQ'D

ASREQ'D

ASREQ'D

ASREQ'D

ASREQ'D

EXIT LIGHTING FIXTURE, SINGLE-FACE, WHITE THERMOPLASTICHOUSING WITH GREEN LETTERS,LEFT DIRECTION ARROW.

EXIT LIGHTING FIXTURE, SINGLE-FACE, WHITE THERMOPLASTICHOUSING WITH GREEN LETTERS,RIGHT DIRECTION ARROW.

NOTE 3

NOTES 3 & 4

NOTES 3 & 4

F5F SAME AS FIXTURE "F5", 8' X 14' CORNER DESIGN.

SATIN ACRYLICLENS

ALUMINUMREFLECTOR

ALUMINUMREFLECTOR------ ---

Red

Wht

Wht

Blk/Orn Blue

Blue

Relay (if req'd)

Normally Closed

Photocell (if req'd)

CommonNormally Open

Auto Dimming Ctrl (if req'd)

7-Brn8-Vio

6-Gry5-Blu

4-Vio w/Wht stripe

3-Blk2-Wht1-Red

SWITCH "a"N

SWITCH "b"

PowerPack

AdditionalOccupancy

Sensor(qty. as

shown onLightingPlans)

3-WAYSWITCH

3-WAYSWITCH

4-WAYSWITCH

UNSWITCHED HOT CONDUCTOR.

SWITCHED HOT CONDUCTOR.

OccupancySensor

TYPICAL MULTI-CONTROL LIGHTING CONTROL DIAGRAMNO SCALE

7-Brn8-Vio

6-Gry5-Blu

4-Vio w/Wht stripe

3-Blk2-Wht1-Red

Blk

Relay (if req'd)Relay (if req'd)

Relay (if req'd)

Normally Closed

Photocell (if req'd)

CommonNormally Open

Auto Dimming Ctrl (if req'd)

Relay (if req'd)Relay (if req'd)

Red Wht Blk

UNSWITCHED HOT CONDUCTOR.

N

Blk/Orn

Wht

PowerPack

Blue

BlueSWITCH "a"

SWITCH "b"

3-WAYSWITCH

4-WAYSWITCH

3-WAYSWITCH

SWITCHED HOT CONDUCTOR.

GENERAL LIGHTINGCONTROL NOTES:A. CONTROL DIAGRAM IS BASED ON ANOCCUPANCY SENSOR BY SENSOR SWITCHAND IS FOR THE PURPOSE OF INDICATING THEDESIRED TYPICAL OPERATION IN SPACES WITHONE OR MORE SWITCHES AND ONE OR MOREOCCUPANCY SENSORS. CONTRACTOR SHALLBE RESPONSIBLE FOR ANY DESIGN CHANGESREQUIRED TO USE PRODUCTS BY ANOTHERMANUFACTURER.

B. IT IS NOT THE INTENT OF THIS DRAWINGTO SHOW, NOR DOES THIS DRAWING SHOWEVERY CONFIGURATION OF LIGHTINGCONTROL DIAGRAM REQUIRED. THECONTRACTOR SHALL BE RESPONSIBLE FORWIRING ALL LIGHTING CONTROL PER THELIGHTING CONTROL SYSTEMMANUFACTURER'S REQUIREMENTS.

C. OPERATION: OCCUPANCY SENSOR(S)SHALL ALLOW LIGHTING WITHIN THE SPACE TOBE TURNED ON [VIA THE LIGHTING CONTROLSWITCH(S)] WHENEVER OCCUPANCY ISDETECTED. THE LIGHTING SHALL REMAIN "ON"UNTIL THE AREA HAS BEEN UNOCCUPIED FORA PERIOD OF 10 MINUTES, (UNLESS NOTEDOTHERWISE), OR THE CONTROL SWITCH ISTURNED "OFF".

D. SWITCH CONFIGURATIONS SHOWN AREFOR WIRING REFERENCE ONLY. THE SWITCHCONFIGURATION FOR A PARTICULAR SPACEMAY BE A COMBINATION OF THE ABOVE TYPESOF SWITCHING ARRANGEMENTS. THESWITCHING REQUIRED FOR EACH SPACESHALL BE AS INDICATED AND DESCRIBED FOREACH SPACE ON THE LIGHTING PLANS.

DIMMER "c"

1/4" = 1'-0"FIRST FLOOR LIGHTING PLAN

A

M

R

ED

N

D

STATE OF

PE60900441

OF I

SS

E

OI

N

R

M

P

E

NLA

I A

E

N A N

GI

ER

AN

W

T

HT EGE

. BEIST

J

R

R CKO

NO.

Drawing No:


Sheet title:

Revisions:



Orr Center:




March, 20171701-109

03/14/2017

E3.1

FIRST FLOOR LIGHTING PLAN

CWWCWW CWW

2'0' 4' 8'

North

1. PROVIDE ALL LABOR AND MATERIAL TO CONNECT NIGHT LIGHTING AND EXIT SIGNSTO PANEL "EHB", CIRCUIT 13. PANEL "EHB" IS LOCATED IN THE BASEMENT MECHANICALROOM 003.

2. PROVIDE OCCUPANCY SENSOR WITH SENSING PATTERN AS REQUIRED TO COVERAREA WITHIN ROOM. LOCATE AND AIM OCCUPANCY SENSOR AS REQUIRED TO DETECTOCCUPANCY WITHIN ROOM BUT NOT TRIGGER "OCCUPANCY" FROM PERSON MOVING INCORRIDOR (OR SPACE) JUST OUTSIDE THE COMMON WALL.

NOTES:

# Description Date

Date post:	20-Aug-2018
Category:	Documents
Upload:	truongdien
View:	215 times
Download:	0 times

E:Revit Projectsx1-109 USI Orr Ctr Adm & Reg Office...

Documents