ESD WORK TABLE WITH DIGITAL REWORK STATION(SMD Rework / PTH Rework)
Package - 1
SMD ComponentsSoldering
PTH Desoldering QFP / PLCC / SOICSOP Desoldering
Illuminated Magnifier Fume Absorber
TIP Activator
DIGITAL REWORK STATION SMD / PTH Rework Station
Soldering and De Soldering Station
Input Voltage 190 v to 270v
Out put Voltage 24v AC
Soldering Wattage 60 Watts
De Soldering Wattage 70 Watts
Temp range 180-480°c
Temp accuracy +/- 1 °c
Tip to ground potential under 2 M.V
Tip to ground Leakage under 2
Vacuum600 mm/Hg
High Quality 24V DC Pump with 4000 RPM SMD Hot AirInput Voltage Power Consumption 300 WattsAir Pump Diaphragm type Capacity 24 L/min Hot air temperature 200 to 550Temp accuracy +/- 1°cSMT Hot Tweezers 2X25w
Motor will switch off automatically after reaching 100°c when the element is switched off.
* Optional Suitable for the above model 999 MC 3 in one SMT Hot Tweezer
* Optional SMD Iron with built in vacuum Pickup Facility for both models For Model 999MC 4 in one Additional FeatureSMT TWEEZER Handle 2 X 25 Watts
220 v AC
TECHNICAL FEATURES
SYSTEM INCLUDES
Soldering Bits – 10 Nos
De Soldering Nozzles 03 Nos
Smt Hot Tweezers Set – 02 Nos
Smd Hot Air – 03 Single Hole Nozzle
Fiber Filters (50 Nos A Set) Primary
Fiber Filters (10 Nos A Set) Secondary
Silicon Washers Set (02 Sets)
Glass Tubes - 02
Cleaning Springs - 03
Combined Stand Soldering & DeSoldering
SMD Hot Air Stand
SMT Hot Tweezer Stand
GENERAL FEATURES
❖ Auto tune PID Control Circuit.
❖ Ease of operation
❖ Set / Read of Operation
❖ Separate switches for increase & decrease of temperature,
after two seconds the actual read of temp will display
❖ Intelligent Power Management auto stand by on mains interruption to save power
❖ Temperature control accuracy +/-1° C
❖ If sensor fails power to the element is shut off
❖ Burn Proof silicon cable thermal resistance up to 600 °C
TIP Activator
TIP Activator
Solder Wire Roll
ESD Brush
Wrist Strap
ESD Slippers Foot Rest for ESD Table
Wooden Drawer Illuminated Magnifier5X
ESD CHAIR Glouses
Flux Dispenser
Desolder Wick
Vaccum Pickup Pencil
ESD Rubber Mat
Smoke Absorber
Flush Cutter
Fine Precision Tweezer Set
SMD KIT Flux Pen
ESD Apron
ESD Work Table
ESD Laminated instrument storage shelf 1 No.
Tube Light fitting 1 No.
Drawing Borad 1 No.
Electrical Panel 1 No.
a. Multipurpose 3 pin sockets 6 Nos.
b. Switch Tube Light 1 No.
c. Indicator 1 No.
Static dissipative table top size : 5 ‘ x 2½ ‘ 1 No.
Remote Jack (For Wrist Strap) 1 No.
Foot Rest 1 No.
Conductive Floor Mat 1.5 M x 1M 1 No.
Detachable drawer 1 No.
Dismantling type Aluminium section (40mm sq) 1 No.
Wrist strap with coil cord 1 No.
Antistatic Gloves 1 Pair
Illuminated Magnifier 1 No.
Antistatic bins 9 Nos.
Bin holder 1 No.
Antistatic Operator Chair – Qty : 1 No.
Specifications:
Height adjustable
RevolvingColour : Black
With Antistatic Cushioned Seat & Back.
A additional attachment of a brass chain clamped on the bottom of the chair for additional grounding purpose is also provided.
Pneumatically Operated
One conductive Castor Wheel remaining normal wheels.
Meets the ANSI ESD S2010.2007 and EIA 625 Standards.6Antistatic Chair : Surface Resistivity of seat & back to the Ground 10 – 10 Ohms / Sq.
Meets the ANSI ESD S2010.2007 and EIA 625 Standards.
10
Pluto 999MC Digital Rework Station(Soldering Iron, Desoldering, SMD Hot Air, SMT Hot Tweezer)]
Package - 1 Includes
ESD Work Table
Rework Station
(Soldering Iron, Desoldering, SMD Hot Air, SMT Hot Tweezer)
SMD Single Hole Nozzles
TIP Activator
Flux Dispenser
SMD KIT
Flux Pen
Solder Wire Roll
Desolder Wick
ESD Rubber Mat
Flush Cutter
ESD Brush
Vaccum Pickup Pencil
Smoke Absorber
Fine Precision Tweezer Set
Wrist Strap
ESD Apron
ESD Chair
Glouses
ESD Slippers
Foot Rest for ESD Table
Wooden Drawer
Illuminated Magnifier 5X
Antistatic Wrist Strap
Flush Cutter
Smoke Absorber
Flux Dispenser
01
01
01
1 Set (3Nos.)
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
Phone : 9618231000, 9866682310 Fax : 040-27159726Email : [email protected], [email protected] : www.plutostations.com
