+ All Categories
Home > Documents > ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager...

ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager...

Date post: 28-Jul-2018
Category:
Upload: phamthuan
View: 254 times
Download: 1 times
Share this document with a friend
20
ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 Initial Setup Copyright Fujitsu Technology Solutions, Release August 2011 Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 0
Transcript
Page 1: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

ETERNUSDX80 S2, DX90 S2,DX410 S2 and DX440 S2

Initial Setup

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 0

Page 2: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Connect FST to DX80 S2 / DX90 S2 Connect FST to DX400 S2 Initial Configuration of the FST Initial Configuration Web GUI Initial Wizard System Setup Initial Manual Setup

Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 Copyright Fujitsu Technology Solutions, Release August 2011

Content

1

Page 3: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Connect FST to DX80 S2 / DX90 S2DX80 S2 and DX90 S2 systems have one MNT LAN port per

CM The MNT port is shared for both the Field Engineer and customer

administration tasks Connect the LAN cable of the Field Service Terminal (FST) to the port

labeled "MNT" at the Controller Module• The "Master LED" of the respective CM lights in green

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

MNT PortMaster LED

2

Page 4: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Connect FST to DX400 S2DX400 S2 systems support a specific FST LAN port per CM Connect the LAN cable of the Field Service Terminal (FST) to the port

labeled "FST" at the Controller Module• The "Master LED" of the respective CM lights in green

Separate LAN port labeled "MNT" at each CM can be connected to the customer LAN Both ports can be used for Field Engineer as well as for customer

administration tasks

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

FST PortMaster LED MNT Port

3

Page 5: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Configuration of the FSTConnect the FST to the Master CM of the ETERNUS DX S2

system

The default IP address of the ETERNUS Manager GUI• http://192.168.1.1/

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Web browser Internet Explorer 7.0/8.0 or laterMozilla Firefox 3.6.x or later

LAN cable Straight cable or cross-linked cable (direct connection)

IP Address/Subnet maskETERNUS DX S2 Entry: MNT

ETERNUS DX S2 Midrange: FST

Factory default IP Address: 192.168.1.1Factory Subnet mask: 255.255.255.0

IP address of the FST Select it within the same subnet of IP Address that is used for the ETERNUS LAN Port (For example 192.168.1.20)

Caution Do not use a proxy server or cache (Temporary Internet Files)JavaScript and Style Sheet must be enabled for the browser

4

Page 6: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Configuration Web GUI (1)To start the installation procedure, logon to the ETERNUS

DX S2 Web GUI using the standard User Account User name: root Password: root

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 5

Page 7: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Configuration Web GUI (2)The opening screen giving a quick overview about the system

directly appears after log-in to the ETERNUS DX S2 Web GUI

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Status overviewof the system

Global overview aboutconfigured disk capacity

Global Systeminformation

6

Page 8: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Indicator Colour DescriptionGreen Each component is in normal status

Orange Component is under maintenance (self test)

YellowPreventive maintenance is required for some components.Pinned data is detected.

RedThis status sign is displayed under the following conditions Component failure is detected Loop Down is detected

Red

This status sign is displayed under the following conditions Abnormal status is detected at power on Abnormal status is detected at power off, the system has not

started up normally Error during restoration of the operating environment at power-

on The system is abnormal

Initial Configuration Web GUI (3)General status information of the ETERNUS DX S2 system

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 7

Page 9: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Configuration Web GUI (4)Status information of each ETERNUS DX S2 component

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Indicator Colour Description

Green Each component is in normal status

Blue A component is installed but unused

Orange Component is under maintenance (self test)

Yellow Preventive maintenance is required

Red Component failure is detected

8

Page 10: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Wizard System Setup (1)The first Initial Setup Wizard Setup the Storage System Name, Set Date & Time, Change Root

password Feature registration

• Thin Provisioning, Advanced Copy and SED Authentication key Set Network Environment and log out to activate the settings

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 9

Page 11: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Wizard System Setup (2)The second Initial Setup Wizard session can be started after

the first setup is done and it supports the setup of the notification network components SNMP

• Agent Basics, Manager, Agent User, Agent Community, Agent Trap Notification

• e-Mail and syslog

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 10

Page 12: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - Date and Time "System" "System Settings" Time, Date and time zone Daylight Saving Time NTP server

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 11

Page 13: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - Machine NameOptional settings to define system information A self-explanatory name for the ETERNUS DX system A description of the location of the ETERNUS DX installation Contact information of the administrator

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 12

Page 14: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - Password It is always recommended to change the default passwords

(after customer's approval) It is recommended to setup an additional user account with

appropriate permissions to administrate other user accounts• The user account "f.ce" has per default only the permission to change its own

password• Helps in situations with forgotten passwords

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 13

Page 15: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - Network Environment IP Address of the Master CM In the event of an Ethernet link error of the Master CM MNT port, the IP

address is taken over automatically by the Slave CM MNT port In a DX400 S2 system it is also possible to setup the network

environment for the FST port

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Allowed IP List• Default Gateway must be set• Defines all servers that are allowed to access the LAN port of the

ETERNUS DX S2 system• Either Host IP Address and Netmask• Or Network Segment Address and Netmask

14

Page 16: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - Firewall SettingThis window allows or denies different TCP/IP management

services that can be used via the LAN ports "MNT is available in DX S2 systems "FST" is available in DX400 S2 systems only "RMT" is used at Fujitsu site only

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 15

Page 17: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - E-Mail NotificationSetup E-Mail Notification window can be used to define Email notification services Email server settings Email retries

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 16

Page 18: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - Syslog SettingThis window can be used to define up to two syslog servers Any Unix or Linux server with a running "syslog" daemon in which the

remote collection service is enabled Also any other error collection program that supports the standard syslog

protocol can be used• For example Microsoft Operations Manager (MOM)

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 17

Page 19: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Initial Manual Setup - SNMP EnvironmentSetup SNMP Interface SNMP is disabled by default SNMP must be enabled for the other SNMP settings to appear in bold

under the "Action" column

Copyright Fujitsu Technology Solutions, Release August 2011Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 18

Page 20: ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2 · The default IP address of the ETERNUS Manager GUI •  Initial Setup ETERNUS DX80 S2, DX90 S2, DX410 S2 and DX440 S2

Recommended