ETFE FoilConstructions

Systems,Air Managementand Applications

Release: Nov 2018

© 2018

System Electra KS-P01

System appropriate for pneumatic and mechanical pre-stressed foil constructions.

. good twisting properties due to high flexibility . durable sealing to backup-gutter . comfortable installation of thermal separations

. standard-finish as stated above; further finishes on demand . cap screw also with countersunk available (e. g. for facades)

➊

➋

➌

➍

➎

© 2018

Systems

item no. material finish weight dimensions ➊ base extrusion KS-P01-01 aluminum anodized E6/EV1 3,20 kg/m 108 x 40 mm

➋ cap extrusion KS-P01-02 aluminum anodized E6/EV1 0,86 kg/m 94 x 4,5 mm

➌ keder extrusion KS-P01-03 aluminum anodized E6/EV1 0,37 kg/m 23 x 14,5 mm

➍ cap sealing KS-P01-04 EPDM black SH60 0,31 kg/m 108 x 2 mm

➎ cap screw, incl. sealing washer KS-P01-05 A4 5,1 gr/pc

System Electra KS-P01

© 2018

System appropriate for pneumatic and mechanical pre-stressed foil constructions.

. no drillings for fixing of base-extrusion required, because of fixation by hammer-head-bolts . base-extrusion can be used for water-drainage . good twisting properties due to high flexibility . comfortable installation of thermal separations

. standard-finish as stated above; further finishes on demand . cap screw also with countersunk available (e. g. for facades)

System Electra A KS-P01

System Electra A KS-P01

➊

➋

➌

➍

➎

© 2018

item no. material finish weight dimensions ➊ base extrusion KS-P01-06A aluminum anodized E6/EV1 2,75 kg/m 108 x 40 mm

➋ cap extrusion KS-P01-02 aluminum anodized E6/EV1 0,86 kg/m 94 x 4,5 mm

➌ keder extrusion KS-P01-03 aluminum anodized E6/EV1 0,37 kg/m 23 x 14,5 mm

➍ cap sealing KS-P01-04 EPDM black SH60 0,31 kg/m 108 x 2 mm

➎ cap screw, incl. sealing washer KS-P01-05 A4 5,1 gr/pc

Systems

© 2018

System appropriate for pneumatic and mechanical pre-stressed foil constructions.

. high flexibility . no penetration of gutter required . standard-lengths 5 m; further lengths on demand . standard-finish as stated above; further finishes on demand

System Solitaire A KS-P02

System Solitaire A KS-P02

➊

➋

➌

➍

➌

© 2018

item no. material finish weight dimensions ➊ base extrusion KS-P02-01 aluminum anodized E6/EV1 1,11 kg/m 36 x 48 mm

➋ keder extrusion KS-P02-21 aluminum anodized E6/EV1 0,59 kg/m 24 x 38 mm

➌ sealing rubber KS-P02-03 EPDM black SH80 0,4 kg/m 23 x 25 mm

➍ safety screw KS-P02-04 A4 4 gr/pc

Systems

© 2018

System appropriate for pneumatic and mechanical pre-stressed foil constructions

. especially for facades . compensation of tolerances during installation . visual minimization of fixing system . standard-lengths 5 m; further lengths on demand . standard-finish as stated above; further finishes on demand

System Lamora KS-P05

System Lamora KS-P05

➊

➋

➌

➍

© 2018

item no. material finish weight dimensions ➊ base extrusion KS-P05-01 aluminum anodized E6/EV1 2,27 kg/m 56 x 67 mm

➋ keder extrusion KS-P05-02 aluminum anodized E6/EV1 0,32 kg/m 17 x 18 mm

➌ cap 1 extrusion KS-P05-03 aluminum anodized E6/EV1 0,20 kg/m 30 x 12 mm

➍ cap 2 extrusion KS-P05-04 aluminum anodized E6/EV1 0,20 kg/m 30 x 18 mm

Systems

© 2018

Keder-Extrusion Carver KS-P03

System appropriate for mechanical pre-stressed foil constructions and lightweight fabrics.

. high flexibility due to compact profile geometry . for keder-chords dia 8 mm . fixation by standard hexagon-bolts (M8) in C-channel . standard-finish as stated above; further finishes on demand

➊

© 2018

Keder-Extrusion KS-P03

item no. material finish weight dimensions ➊ keder-extrusion KS-P03 aluminum anodized E6/EV1 0,97 kg/m 47 x 19 mm

Systems

© 2018

Keder-Extrusion Rider KS-P04

System appropriate for mechanical pre-stressed textile strucures.

. for coated fabrics type II - V . for max. keder-chords dia 12 mm . fixation by standard hexagon-bolts (M10) in C-channel . standard-finish as stated above; further finishes on demand

➊

© 2018

Keder-Extrusion KS-P04

item no. material finish weight dimensions ➊ keder-extrusion KS-P04 aluminum anodized E6/EV1 1,84 kg/m 36 x 48 mm

Systems

➊

© 2018

AttachmentsThermal Separation KS-A01

item no. material finish weight dimensions

➊ thermal separation, incl. O-ring KS-A01 PBT-fibreglas-reinforced black 5 gr/pc 54 x 4 mm

. thermal separation between alu-minum-extrusion, backup-gutter and secondary structure. . form-fit to base extrusion, to transfer

shear forces and decrease bending moments of bolts . durable sealing between thermal

separation and backup-gutter, due to O-ring seal

➊➋

➌

➍

© 2018

Air ManagementAir Inlet 50 KS-A02A

item no. material finish weight dimensions ➊ clamping plate 1 KS-A02-01A aluminum anodized E6/EV1 62 gr/pc 106 x 4 mm

➋ clamping plate 2 KS-A02-02 aluminum anodized E6/EV1 58 gr/pc 106 x 5 mm

➌ adapter KS-A02-03 aluminum anodized E6/EV1 35 gr/pc 60 x 36 mm

➍ countersunk screw KS-A02-04 stainless steel 2,5 gr/pc M6 x 8 mm

. air inlet for pneumatic pre-stressed ETFE-foil constructions . thread of KS-A02-03 adjusted to

flexible pipe „FK Wellrohr 50/6“ . no hose clamps required . standard finish as stated above;

further finishes on demand

➊ ➋

➌

➍

© 2018

Air ManagementAir Inlet 25 KS-A03A

item no. material finish weight dimensions ➊ clamping plate 1 KS-A03-01A aluminum anodized E6/EV1 38 gr/pc 80 x 4 mm

➋ clamping plate 2 KS-A03-02 aluminum anodized E6/EV1 32 gr/pc 80 x 5 mm

➌ adapter KS-A03-03 aluminum anodized E6/EV1 13 gr/pc 34 x 31 mm

➍ countersunk screw KS-A03-04 stainless steel 2,5 gr/pc M6 x 8 mm

. air inlet for pneumatic pre-stressed ETFE-foil constructions. Only in com-bination with frequency- controlled blower units! . thread of KS-A03-03 adjusted to

flexible pipe FK Wellrohr 25/4“ . no hose clamps required. . standard finish as stated above;

further finishes on demand

➊➋

➌

➍

➎➏

© 2018

Air ManagementAir Outlet KS-A05

item no. material finish weight dimensions ➊ clamping plate 1 KS-A05-01 aluminum anodized E6/EV1 28 gr/pc 64 x 4 mm

➋ clamping plate 2 KS-A05-02 aluminum anodized E6/EV1 26 gr/pc 64 x 5 mm

➌ socket KS-A05-03 aluminum anodized E6/EV1 4 gr/pc 18 x 16 mm

➍ countersunk screw KS-A05-04 stainless steel 2,5 gr/pc M6 x 8 mm

➎ reduction plate KS-A05-05 ETFE-foil 19 mm

➏mesh disc KS-A05-06 ETFE-mesh 19 mm

. air outlet for pneumatic pre-stressed ETFE-foil constructions . required airflow achieved by reduction-

plates . standard finish as stated above;

further finishes on demand

➊➋

➌

© 2018

Air ManagementClamping Ring KS-A06

item no. material finish weight dimensions ➊ clamping plate 1 KS-A06-01 aluminum anodized E6/EV1 38 gr/pc 64 x 4 mm

➋ clamping plate 2 KS-A06-02 aluminum anodized E6/EV1 39 gr/pc 64 x 5 mm

➌ countersunk screw KS-A06-03 stainless steel 2,5 gr/pc M6 x 8 mm

. air-management-component for pneu-matic ETFE-foil constructions with more than one middle-layer . standard finish as stated above; further

finishes on demand

➊➋

➌

➍

© 2018

Air ManagementPressure-Management-Adapter KS-A07

item no. material finish weight dimensions ➊ clamping plate 1 KS-A07-01 aluminum anodized E6/EV1 19 gr/pc 54 x 4 mm

➋ clamping plate 2 KS-A07-02 aluminum anodized E6/EV1 21 gr/pc 54 x 5 mm

➌ adapter KS-A07-03 aluminum anodized E6/EV1 1 gr/pc

➍ countersunk screw KS-A07-04 stainless steel 2,5 gr/pc M6 x 8 mm

. measurement of the inner-pressure of pneumatic pre-stressed ETFE-foil const-ructions . for assembly of pressure-measure-

ment-tubes with inner diameters of 4 and 5 mm . standard finish as stated above; . further finishes on demand

➊

© 2018

applicationsattachmentsProtection-Kit KS-A08

item no. material finish weight dimensions ➊ protection-kit KS-A08 PA - 1 gr/pc mm

. attachment for Systems Electra, Electra A and Solitaire . protection-kit for the installation process . no deburring of keder-extrusions required

➊

© 2018

applicationsattachmentsProtection-Kit KS-A09

item no. material finish weight dimensions ➊ protection-kit KS-A09 PA - 1 gr/pc

. attachment for keder-extrusion Carver . protection-kit for the installation process . no deburring of keder-extrusions required

➊

© 2018

applicationsattachmentsProtection-Kit KS-A10

item no. material finish weight dimensions ➊ protection-kit KS-A10 PA - 1 gr/pc

. attachment for keder-extrusion Rider . protection-kit for the installation process . no deburring of keder-extrusions required

➊

© 2018

applicationsattachmentsConnection-Pin KS-A12

item no. material finish weight dimensions ➊ connection-pin KS-A12 A2 - 18 gr/pc 3 x 80 mm

. attachment for Systems Electra A, Solitaire and Lamora . connection-pin at extrusion-joints to

avoid height gaps

➊

© 2018

applicationsattachmentsConnection-Bar KS-P01-10

item no. material finish weight dimensions ➊ connection-bar KS-P01-10 aluminum - 74 gr/pc 21 x 8 x 160 mm

. attachment for Systems Electra A . connection-bar at extrusion-joints to

avoid height gaps . statical coupling of two base-extrusions

konstruct AG

Am Rossacker 983022 Rosenheim / Germany

Telefon: +49 (8031) 941 388-0Telefax: +49 (8031) 941 388-18

E-Mail: info@konstruct-ag.comwww.konstruct-ag.com

konstruct systems

Schopperstrasse 283131 Nussdorf am Inn / Germany

Telefon: +49 (8031) 941 388-0Telefax: +49 (8031) 941 388-18

E-Mail: info@konstruct-ag.comwww.konstruct-ag.com