EtherWAN EX42205-0T User Manual

7/24/2019 EtherWAN EX42205-0T User Manual

1/21

EX42200 www.etherwan.com

Quick Start Guide

This quick start guide describes how to install and use theHardened PoE Ethernet Switch. Capable of operating attemperature extremes of -40C to +75C, this is the switch ofchoice for harsh environments constrained by space.

Physical Description

The Terminal Block and Power Inputs

Power Input Assignment

18~57VDCPower1

Power Ground

18~57VDCPower2

Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 250VAC

Relay Alarm Assignment

Default is Power1 and Power2 both off.Point 1 & 2 is close and Point 2 & 3 is open.

DC Terminal Block Power Inputs: There are two pairs of

power inputs can be used to power up this switch. Redundantpower supplies function is supported.

1


2/21


The 10/100Base-TX and 100Base-FX/BX Connectors

1. The 10/100Base-TX Connections

The following lists the pinouts of 10/100Base-TX ports.

Pin Signal Name Signal Defin ition

1 TD Output Transmit Data

2 TD Output Transmit Data

3 RD Input Receive Data

4 PoE Positive (VCC)

5 PoE Positive (VCC)

6 RD Input Receive Data

7 PoE Negative (VCC)8 PoE Negative (VCC)

2. The 100Base-FX ConnectionsThe fiber port pinouts: The Tx (transmit) port of device I isconnected to the Rx (receive) port of device II, and the Rx(receive) port of device I to the Tx (transmit) port of device II.

3. The WDM 100Base-BX ConnectionsThe fiber port pinouts: Only one single optical fiber is requiredto transmit and receive data.

2


3/21


The Port Status LEDs

3


4/21


4

LED State Indication

Steady Power on.Power1Power2 Off Power off.

Steady Power redundant system failure occurred.Alarm

Off Power redundant system failure is not occurred.

10/100Base-TX

Steady A valid network connection established.

LINK/ACTFlashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.10/100

Off Valid port connection at 10Mbps.

Steady Powered device (PD) is connected.PoE

Off Powered device (PD) is disconnected.

100Base-FX/BX


LINK/ACTFlashing



Steady Valid port connection at 100Mbps.100

Off No valid port connection at 10Mbps.


5/21


5

Functional Description

Meets EN61000-6-2 & EN61000-6-4 EMC GenericStandard Immunity for industrial environment.

Supports IEEE802.3at Power over Ethernet (PoE)Power Sourcing Equipment (PSE).

Port 1 to 4 support PoE function, IEEE802.3at Power

over Ethernet (PoE) and 10/100Base-TX. Up to 30W per PoE port, 55VDC, 600mA Max. Supports IEEE802.3/802.3u/802.3x. 10/100Mbps,

Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX. 100Base-FX: Multi/Single mode SC or ST type.

100Base-BX: WDM Multi/Single mode SC type. Supports 2048 MAC addresses. Provides 448K bits

buffer memory. Alarms for power failure by relay output. Fully supports

normal open and normal close. Redundant dual 18 to 57VDC Terminal Block power

inputs. Device power consumption: 14W Max. (without PoE).

PoE power budget: 120W Max.

Operating temperature ranges from -40 to 75

(-40to 167), tested for functional operation @ -40

to 85 (-40to 185).

Supports DIN-Rail installation.

Assembly, Startup, and Dismantling

Assembly: Place the switch on the DIN rail from aboveusing the slot. Push the front of the switch toward themounting surface until it audibly snaps into place.

Startup: Connect the supply voltage to start up the

switch via the terminal block. Dismantling: Pull out the lower edge and then remove

the switch from the DIN rail.


6/21


6


7/21


7

Preface

A member of the growing family of rugged switches, thisHardened PoE Ethernet Switch addresses a need for asmaller switch. This switch provides an affordable solution forrugged and outdoor environment, transportation road-sidecabinet, industrial floor shop, multitenant dwellings or Fiber ToThe Home (FTTH) applications. Capable of operating at

temperature extremes of -40C to +75C, this is the switch ofchoice for harsh environments constrained by space.

Port 1 to port 4 on this Switch supports IEEE802.3at Powerover Ethernet (PoE) Power Sourcing Equipment (PSE) andcan detect an IEEE802.3at compliant Powered Device (PD).Using external 18~57VDC power inputs through Terminal

Block, data and power can be transmitted to a PoweredDevice (PD) over the same twisted-pair Ethernet cablethrough port 1 to port 4 on the Switch.

This manual describes how to install and use the HardenedPoE Ethernet Switch. This switch integrates full wire speedswitching technology. This switch brings the answer to

complicated Industrial networking environments.

To get the most out of this manual, you should have anunderstanding of Ethernet networking concepts.

In this manual, you will find:

Features on the switch Illustrative LED functions Installation instructions Specifications


8/21


8

Table of Contents

QUICK START GUIDE 1

PHYSICAL DESCRIPTION 1

The Terminal Block and Power Inputs 1The 10/100Base-TX and 100Base-FX/BX Connectors 2The Port Status LEDs 3

FUNCTIONAL DESCRIPTION 5

ASSEMBLY,STARTUP,AND DISMANTLING 5

PREFACE 7

TABLE OF CONTENTS 8

PRODUCT OVERVIEW 9

HARDENED POEETHERNET SWITCH 9

PACKAGE CONTENTS 9

PRODUCT HIGHLIGHTS 10

Basic Features 10

FRONT PANEL DISPLAY 11

PHYSICAL PORTS 13

INSTALLATION 14

SELECTING A SITE FOR THE SWITCH 14

DINRAIL MOUNTING 15CONNECTING TO POWER 16

Redundant DC Terminal Block Power Inputs 16Alarms for Power and Port Link Failure 17

CONNECTING TO YOUR NETWORK 18

Cable Type & Length 18Cabling 19

SPECIFICATIONS 20


9/21


Product Overview

Hardened PoE Ethernet Switch

Package Contents

When you unpack the product package, you shall find the

items listed below. Please inspect the contents, and reportany apparent damage or missing items immediately to yourauthorized reseller.

This Switch Users Manual

9


10/21


10

Product Highlights

Basic Features

Meets EN61000-6-2 & EN61000-6-4 EMC GenericStandard Immunity for industrial environment.

Supports IEEE802.3at Power over Ethernet (PoE)Power Sourcing Equipment (PSE).

Port 1 to 4 support PoE function, IEEE802.3at Powerover Ethernet (PoE) and 10/100Base-TX. Up to 30W per PoE port, 55VDC, 600mA Max. Supports IEEE802.3/802.3u/802.3x. 10/100Mbps,

Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX. 100Base-FX: Multi/Single mode SC or ST type.

100Base-BX: WDM Multi/Single mode SC type. Supports 2048 MAC addresses. Provides 448K bits

buffer memory. Alarms for power failure by relay output. Fully supports

normal open and normal close. Redundant dual 18 to 57VDC Terminal Block power

inputs. Device power consumption: 14W Max. (without PoE).

PoE power budget: 120W Max. Operating temperature ranges from -40 to 75

(-40to 167), tested for functional operation @ -40

to 85 (-40to 185).

Supports DIN-Rail installation.


11/21


Front Panel Display

11


12/21


12

Status LEDs

LED State Indication

Steady Power on.Power1

Power2 Off Power off.

Steady Power redundant system failure occurred.Alarm

Off Power redundant system failure is not occurred.

10/100Base-TX


LINK/ACTFlashing



Steady Valid port connection at 100Mbps.10/100

Off Valid port connection at 10Mbps.

Steady Powered device (PD) is connected.

PoEOff Powered device (PD) is disconnected.

100Base-FX/BX


LINK/ACTFlashing



Steady Valid port connection at 100Mbps.100Off No valid port connection at 10Mbps.


13/21


13

Physical Ports

This switch provides: Five 10/100Base-TX ports Four 10/100Base-TX ports + one 100Base-FX/BX port

CONNECTIVITY

RJ-45 connector on TX ports SC or ST connector on 100Base-FX fiber port SC connector on 100Base-BX fiber port


14/21


14

Installation

This chapter gives step-by-step instructions about how toinstall the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch

where it will not be subjected to extreme temperatures,humidity, or electromagnetic interference. Specifically, the siteyou select should meet the following requirements:

The ambient temperature should be between -40 to 75degrees Celsius.

The relative humidity should be less than 95 percent,non-condensing.

Surrounding electrical devices should not exceed theelectromagnetic field (RFC) standards.

Make sure that the switch receives adequate ventilation.Do not block the ventilation holes on each side of theswitch

The power outlet should be within 1.8 meters of theswitch.


15/21


DIN Rail Mounting

Fix the DIN rail attachment plate to the back panel of theswitch.

Installation: Place the switch on the DIN rail from above usingthe slot. Push the front of the switch toward the mounting

surface until it audibly snaps into place.

Removal: Pull out the lower edge and then remove the switchfrom the DIN rail.

15


16/21


Connecting to Power

Redundant DC Terminal Block Power Inputs

There are two pairs of power inputs can be used to power upthis device. You only need to have one power input connectedto run the switch.

Step 1: Connect the DC power cord to the plug-able terminal block on theswitch, and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the switch.

16


17/21


Alarms for Power and Port Link Failure

Step 1: There are three pins on the terminal block are used for power failure

detection. It fully supports normal open and normal close. Use thisas a dry contact application to send a signal for power failuredetection.

Power Input Assignment

18~57VDCPower1

Power Ground

18~57VDC

Power2 Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 250VAC

Relay Alarm Assignment

Default is Power1 and Power2 both off.Point 1 & 2 is close and Point 2 & 3 is open.

Relay Contact Power1 Power2 Point 1 & 2 Point 2 & 3

Start Alarm Off Off Close Open

Start Alarm Off On Close Open

Start Alarm On Off Close Open

Non-Alarm On On Open Close

17


18/21


18

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below whenconnecting the switch to your network. Use appropriatecables that meet your speed and cabling requirements.

Cable S ecificationspSpeed Connector Port SpeedHalf/FullDuplex

Cable Max.Distance

10Base-T RJ-45 10/20 Mbps 2-pairUTP/STPCat. 3, 4, 5

100 m

100Base-TX RJ-45 100/200 Mbps 2-pairUTP/STP

Cat. 5

100 m

100Base-FX SC, ST 200 Mbps MMF (50 or62.5m)

2 km

100Base-FX SC, ST 200 Mbps SMF (9 or10m)

20 or 40 km

100Base-BX SC 200 Mbps MMF (50 or62.5m)

2 or 5 km

100Base-BX SC 200 Mbps SMF (9 or10m)

20 or 40 km


19/21


19

Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of portin use.

Step 3: Consult the previous section for cabling requirements based onconnectors and speed.

Step 4: Connect one end of the cable to the switch and the other end to adesired device.

Step 5: Once the connections between two end devices are madesuccessfully, turn on the power and the switch is operational.


20/21


20

Specifications

Hardened PoEEthernet Switch

10/100Base-TX auto-negotiating ports withRJ-45 connectors, 100Base-FX/BX fiber port

ApplicableStandards

IEEE 802.3 10Base-TIEEE 802.3u 100Base-TX/FX

Switching Method Store-and-Forward

Forwarding Rate10Base-T:100Base-TX:

100Base-FX/BX:

10 / 20Mbps half / full-duplex100 / 200Mbps half / full-duplex

200Mbps full-duplexPerformance 14,880pps for 10Mbps

148,810pps for 100Mbps

Cable10Base-T:100Base-TX:

100Base-FX/BX:

4-pair UTP/STP Cat. 3, 4, 54-pair UTP/STP Cat. 5Up to 100m (328ft.)MMF (50 or 62.5m), SMF (9 or 10m)

LED Indicators Per unit Power status (Power 1, Power 2), Alarm

Per port 10/100TX - LINK/ACT, 100, PoE100FX/BX - LINK/ACT, 100

Dimensions 61mm (W) 73mm (D) 110mm (H)(2.4 (W) x 2.87 (D) x 4.33(H))

Net Weight 0.6Kg (1.32lbs.)

Power Terminal Block: 18~57VDCPower Consumption Device: 14W Max. (without PoE)

PoE power budget: 120W Max.OperatingTemperature

-40to 75(-40to 167)

Tested @ -40to 85(-40to 185)

Storage Temperature -40to 85(-40to 185)

Humidity 5%-95% non-condensing

EMI

FCC Part 15, Class A

CE, VCCI Class A

EN61000-6-4

EN55022

EN61000-3-2

EN61000-3-3

EMSEN61000-6-2

EN61000-4-2 (ESD Standard)


21/21


EN61000-4-3 (Radiated FRI Standards)

EN61000-4-4 (Burst Standards)

EN61000-4-5 (Surge Standards)

EN61000-4-6 (Induced RFI Standards)

EN61000-4-8 (Magnetic Field Standards)

Environmental Test Compliance

IEC60068-2-6 Fc (Vibration Resistance)

IEC60068-2-27 Ea (Shock)

FED STD 101C Method 5007.1 (Free Fall with package)

Date post:	21-Feb-2018
Category:	Documents
Upload:	jmac-supply
View:	245 times
Download:	0 times

EtherWAN EX42205-0T User Manual

Documents