Sira Certification Service Unit 6 Hawarden Industrial Park, Hawarden, CH5 3US, United Kingdom Tel: +44 (0) 1244 670900 Fax: +44 (0) 1244 681330 Email: [email protected]Web: www.csagroupuk.org Project Number 70175530 C Ellaby Deputy Certification Manager This certificate and its schedules may only be reproduced in its entirety and without change. Page 1 of 10 Form 9400 Issue 4 1 EU-TYPE EXAMINATION CERTIFICATE 2 Equipment intended for use in Potentially Explosive Atmospheres Directive 2014/34/EU 3 Certificate Number: Sira 12ATEX1123X Issue: 10 4 Equipment: IQ Range of Electric Valve Actuators 5 Applicant: Rotork Controls Ltd Rotork Controls Inc Rotork Actuation (Shanghai) Co Ltd, 6 Address: Brassmill Lane Bath, BA1 3JQ England 675 Mile Crossing Blvd Rochester New York 14624 USA Building G, No 260, Liancao Road Minghang District Shanghai China 7 This equipment and any acceptable variation thereto is specified in the schedule to this certificate and the documents therein referred to. 8 Sira Certification Service, notified body number 0518 in accordance with Articles 17 and 21 of Directive 2014/34/EU of the European Parliament and of the Council, dated 26 February 2014, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment intended for use in potentially explosive atmospheres given in Annex II to the Directive. The examination and test results are recorded in the confidential reports listed in Section 14.2. 9 Compliance with the Essential Health and Safety Requirements, with the exception of those listed in the schedule to this certificate, has been assured by compliance with the following documents: EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007 EN 60079-31:2009 EN 13463-1:2009 EN 13463-5:2011 The above list of documents may detail standards that do not appear on the UKAS Scope of Accreditation, but have been added through Sira’s flexible scope of accreditation, which is available on request. 10 If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to Specific Conditions of Use identified in the schedule to this certificate. 11 This EU-Type Examination Certificate relates only to the design and construction of the specified equipment. If applicable, further requirements of this Directive apply to the manufacture and supply of this equipment. 12 The marking of the equipment shall include the following: II 2GD c Ex dIIB T4 Gb Ex tb IIIC T120°C Db IP68/IP66“e” added on versions with increased safety terminal enclosure Only IP64 is endorsed by Sira on this certificate Ta = (-C to +C) down to -50C, up to 70C The IQD** and IQH** models are not available as a low temperature version (below -20°C)
Transcript
Sira Certification Service Unit 6 Hawarden Industrial Park, Hawarden, CH5 3US, United Kingdom
Project Number 70175530 C Ellaby Deputy Certification Manager This certificate and its schedules may only be reproduced in its entirety and without change. Page 1 of 10 Form 9400 Issue 4
1 EU-TYPE EXAMINATION CERTIFICATE 2 Equipment intended for use in Potentially Explosive Atmospheres Directive 2014/34/EU 3 Certificate Number: Sira 12ATEX1123X Issue: 10 4 Equipment: IQ Range of Electric Valve Actuators 5 Applicant: Rotork Controls Ltd Rotork Controls Inc Rotork Actuation (Shanghai)
Co Ltd, 6 Address: Brassmill Lane
Bath, BA1 3JQ England
675 Mile Crossing Blvd Rochester New York 14624 USA
Building G, No 260, Liancao Road Minghang District Shanghai China
7 This equipment and any acceptable variation thereto is specified in the schedule to this certificate and
the documents therein referred to. 8 Sira Certification Service, notified body number 0518 in accordance with Articles 17 and 21 of Directive
2014/34/EU of the European Parliament and of the Council, dated 26 February 2014, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment intended for use in potentially explosive atmospheres given in Annex II to the Directive.
The examination and test results are recorded in the confidential reports listed in Section 14.2. 9 Compliance with the Essential Health and Safety Requirements, with the exception of those listed in the
schedule to this certificate, has been assured by compliance with the following documents:
EN 60079-0:2009 EN 60079-1:2007 EN 60079-7:2007 EN 60079-31:2009 EN 13463-1:2009 EN 13463-5:2011
The above list of documents may detail standards that do not appear on the UKAS Scope of Accreditation, but have been added through Sira’s flexible scope of accreditation, which is available on request.
10 If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to Specific
Conditions of Use identified in the schedule to this certificate. 11 This EU-Type Examination Certificate relates only to the design and construction of the specified
equipment. If applicable, further requirements of this Directive apply to the manufacture and supply of this equipment.
12 The marking of the equipment shall include the following:
II 2GD c Ex d� IIB T4 Gb Ex tb IIIC T120°C Db IP68/IP66� � “e” added on versions with increased safety terminal enclosure � Only IP64 is endorsed by Sira on this certificate Ta = (-�°C to +�°C) �down to -50°C, �up to 70°C The IQD** and IQH** models are not available as a low temperature version (below -20°C)
This certificate and its schedules may only be reproduced in its entirety and without change. Page 2 of 10 Form 9400 Issue4
13 DESCRIPTION OF EQUIPMENT
The IQ Range of Electric Valve Actuators comprises an oil-filled worm gearcase with a rotating shaft and drive bush, an external handwheel and de-clutch mechanism. Attached to the gearcase is a motor enclosure, an electrical control enclosure and a terminal enclosure. All electrical enclosures are designed to satisfy the requirements for flameproof equipment. In addition, the terminal enclosure is designed to satisfy the requirements for increased safety, providing an alternative method of protection for the field wiring facilities. The IQ Electric Actuator comprises a range of electric actuators based upon various gearcase sizes.
The motor enclosure is formed by a cover which connects to the gearcase by means of a spigoted flamepath joint and is secured by four M8 capscrews. The rotary output from the motor transfers to the gearcase by means of a shaft supported by rolling element bearings and a cylindrical brass bushing forming its flamepath. Electrical services to the motor are supplied from the electrical enclosure via a potted, motor loom transfer bush.
Thermal protection devices are installed within the motor windings. There is a facility to override these devices should the user find it necessary.
NOTE: The overriding of the temperature classification thermal protection devices is not covered by the scope of this certificate.
The electrical enclosure is formed by a cover which connects to the gearcase by means of a spigoted flamepath joint and is secured by four M8 capscrews. The electrical enclosure contains monitoring and control circuitry, which senses and controls the position of the output shaft; it also contains a back-up battery facility, contained within an internal battery pocket, accessed externally via the battery pocket plug.The permitted battery types are: Ultralife PP3 type U9VL/U9VL-J-P, SAFT to Rotork part no 95-462, Tadiran/Sonneschein to Rotork part No 95-614, in each case the battery is is protected by an in-line fuse (permitted fuse types are Quick Blow Bussman S500, 100mA, Quick Blow Littlefuse 217, 100 mA). At one end of the electrical enclosure a window is provided to allow the observation of an internal LCD device. The window is manufactured from toughened glass and potted into the electrical cover. An encoder shaft exits the electrical enclosure via a cylindrical brass bushing, flamepaths being between the bushing and the gearcase and between the shaft and the bushing. The encoder shaft has a shoulder that is held against the shroud by a circlip.
The terminal enclosure connects to the electrical enclosure via the gearcase, their volumes being separated by a flameproof terminal bung. The flameproof terminal bung comprises of moulded plastic main body through which passes a number of terminals which are sealed in place with a potting compound. The terminal bung is secured in position by means of a circlip. The terminal enclosure provides all electrical field wiring terminations at the terminal bung. The above flameproof terminal bung may be replaced with a non-flameproof terminal bung, in which case the electrical and terminal compartments are considered as one flameproof enclosure. This configuration cannot be applied to the variants that incorporate increased safety terminal facilities. Cable entry facilities are provided in the form of three or four threaded entries. The terminal enclosure is closed by means of a lid, which connects to the gearcase by means of a tapered spigot joint and is secured by four M8 capscrews. The terminal compartment is common to all sizes.
All external fasteners are stainless steel, grade A4-80 socket cap head screws.
This certificate and its schedules may only be reproduced in its entirety and without change. Page 3 of 10 Form 9400 Issue4
The following gearcase/motor options are covered:
IQ Gearcase/Motor Configurations 3 phase, up to 690 V rms
Size 1 Gearcase size 1 One motor enclosure, four pole motors, two stator lengths Designated IQ10, 12 & 18.
Size 2 Gearcase size 2 One motor enclosure, with either two or four pole motors, six stator lengths Designated IQ19, 20 & 25.
Size 3 Gearcase size 3 One motor enclosure, with either two or four pole motors, one stator length Designated IQ35.
Size 5 Gearcase size 5 Motor Options Three Motor enclosures: One motor enclosure with two or four pole motor, one stator length Designated IQ40 One motor enclosure with either two or four pole motors, five stator lengths Designated IQ70, IQ90, IQ95. One motor enclosure with a two pole motor, one stator length Designated IQ91
Design Options
Single phase motor option – Actuator sizes 1, 2 and 3
Actuator Motor type IQS12 4 pole 110 to 240 Vrms ± 10% IQS20 4 pole 110 to 240 Vrms ± 10% IQS35 2/4 pole 110 to 240 Vrms ± 10%
Different motor options (as can be seen above) as well as the necessary alternative control equipment within the electrical enclosure.
Modulating motor control option for three phase motors – Actuator sizes 1, 2 and 3.
The reversing contactor has been replaced with a solid state starter module, utilising thyristor drives and their associated control electronics, designated:
This certificate and its schedules may only be reproduced in its entirety and without change. Page 4 of 10 Form 9400 Issue4
Deep Terminal Cover Option – All actuator sizes
The deep terminal cover allows the installation of a PCB for various network disconnect applications or a wireless network PCB and associated external aerial enclosure, on Ex d versions. The deep cover is provided with threaded entry points.
Short electrical cover option - Actuator sizes 1, 2 and 3
Used when the internal equipment specified for the IQ Electric Valve Actuator allows a reduced size of electrical enclosure DC Motor options for actuator sizes 1 and 2.
Ambient temperature range -20°C to +70°C (Leeson motor)
Actuator Motor type IQD10, IQD12, IQD18 Short Motor (Leeson motor) IQD20 Short Motor (Leeson motor) IQD25 Long Motor (Leeson motor)
Different motor options (as can be seen above) as well as the necessary alternative control equipment within the electrical enclosure. Intumescent® coating option to the exterior of the actuators for fire proofing purposes.
The application of an outer, Intumescent® fire retardant coating can be applied to all sizes. Lightning suppression module option – All actuator sizes Applies to terminal enclosures that are marked ‘Ex d’ only; it allows the inclusion of a lightning suppression module secured to the inner face of the existing terminal lid.
IQH variant option – Ambient temperature range -20°C to +70°C The following high speed actuator types have been introduced: IQH20, IQH25, IQH35, IQH40
Plug and Socket Cover/ Plug and Socket connection/ Non-Flameproof terminal Bung option – Ex d versions gas group IIB only, all sizes, ambient temperature range -20°C to +70°C.
The flameproof terminal bung is removed and replaced with a non-flameproof plug and socket arrangement, to accommodate the plug and socket arrangement a Plug and Socket Cover has been introduced, manufactured in aluminium alloy to BS 1490 LM25M. The latter includes up to four M25 threaded cable entry points, additionally it can optionally accommodate the Network Disconnect PCB.
Optionally in place of the plug and socket connection facility, a non-flameproof terminal bung can be installed along with the Plug and Socket Cover, with or without the Network Disconnect PCB.
Variation 1 - This variation introduced the following changes: i. The introduction of the Size 5 actuator range, the description was amended to recognise this new size. ii. Following appropriate re-assessment to demonstrate compliance with the requirements of the latest
technical knowledge, EN 13463-5:2003 was replaced by the version currently listed.
This certificate and its schedules may only be reproduced in its entirety and without change. Page 5 of 10 Form 9400 Issue4
iii. The introduction of the deep terminal cover along with either a Profibus ® PCB, or a wireless network PCB and associated aerial enclosure, the description is amended to reflect this new terminal cover. This modification applies only to Ex d versions of the equipment.
iv. The introduction of additional Special Conditions for Safe Use and Conditions of Certification.
Variation 2 - This variation introduced the following changes:
i. The introduction of the short electrical covers as an option on gearcase sizes 1, 2 and 3, the description was amended to recognise this new design and Special Conditions for Safe Use and Conditions of Certification were modified to include the new versions.
ii. The introduction of an alternative absolute encoder shaft, manufactured in steel (sizes 1, 2 and 3). iii. The introduction of a self adhesive battery plug label option (sizes 1, 2 and 3). Variation 3 - This variation introduced the following changes: i. The introduction of DC motor options on gearcase sizes 1 and 2, the description was amended to
recognise this new design. ii. The introduction of an Intumescent® coating for all actuator sizes. Variation 4 - This variation introduced the following changes: i. The introduction of a Lightning Suppression Module was approved; the description was amended
to reflect this change. Variation 5 - This variation introduced the following changes: i. The introduction of the IQH variant – Actuator Size 2, Size 3 and Size 5 (IQ40). Ambient
Temperature Range of –20°C to +70°C. ii. The introduction of an alternative electrical cover manufactured in aluminium alloy to BS1490.
Grade: LM25TF (Heat Treated). iii. Amendments to approval drawings to rectify minor data misalignments (Sira R15000-059A/00 is
replaced by R15000-059A/01). Variation 6 - This variation introduced the following changes: i. The introduction of an alternative Size 2 motor cover (Brook Motor). ii. Amendments to the routine testing associated with the Ex e terminal housing option were approved,
resulting in the modification of a Condition of Certification. iii. Drawings PLAD 1347 and PLAD 1350 have been amended to allow alternative suppliers for certain
bearings. The bearing type remains the same in both cases Variation 7 - This variation introduced the following changes: i. The introduction of a size IQ19 motor (Size 2), the description was amended to reflect this change. ii. The introduction of alternative network disconnect pcbs. Variation 8 - This variation introduced the following changes: i. Various amendments to the approval documents, which include.
• Correction of PLAD1346 issue number from 06 to 7. • Addition of the terminal bung retaining ring Type 38377CH. • Addition of an alternative design for the handwheel cover seal for all sizes. • Alternative internal earth arrangement.
This certificate and its schedules may only be reproduced in its entirety and without change. Page 6 of 10 Form 9400 Issue4
• Alternative low temperature bearings added. • Alternative wormshafts & wormwheels added.
Variation 9 - This variation introduced the following changes: i. Introduction of Loctite 5607® as alternative sealant for the viewing window. ii. The introduction of an alternative electrical cover manufactured in aluminium alloy to ASTM B85,
Grade: A360 modified to accept an anti-vandal fixture. iii. Amendments to approval drawings to reflect the above modifications and incorporate minor
amendments. Variation 10 - This variation introduced the following changes: i. Introduction of Plug and Socket Cover/ Plug and Socket connection/ Non-Flameproof terminal Bung
option – Ex d versions gas group IIB only, all sizes, ambient temperature range -20°C to +70°C. ii. Introduction of Rotork Actuation (Shanghai) Co Ltd, as additional ‘applicant’ and ‘manufacturer’
14 DESCRIPTIVE DOCUMENTS 14.1 Drawings
Refer to Certificate Annexe. 14.2 Associated Sira Reports and Certificate History
Issue Date Report number Comment 0 20 August 2012 R15000-051A/00 The release of the prime certificate. 1 02 November 2012 R15000-059A/00
R15000-060A/00 The introduction of Variation 1.
2 28 November 2012 R15000-057A/00 The introduction of Variation 2. 3 25 January 2013 R15000-056A/00 The introduction of Variation 3. 4 07 June 2013 R15000-065A/00 The introduction of Variation 4. 5 05 August 2014 R70008857A
R15000-059A/01 The introduction of Variation 5.
6 16 September 2015 R70035753A The introduction of Variation 6. 7 02 November 2015 R70047775A The introduction of Variation 7. 8 19 October 2016 R70078570A This Issue covers the following changes:
• EC Type-Examination Certificate in accordance with 94/9/EC updated to EU Type-Examination Certificate in accordance with Directive 2014/34/EU. (In accordance with Article 41 of Directive 2014/34/EU, EC Type-Examination Certificates referring to 94/9/EC that were in existence prior to the date of application of 2014/34/EU (20 April 2016) may be referenced as if they were issued in accordance with Directive 2014/34/EU. Variations to such EC Type-Examination Certificates may continue to bear the original certificate number issued prior to 20 April 2016.)
• The introduction of Variation 8. 9 20 October 2017 R70158418A The introduction of Variation 9 10 19 June 2018 R70175530A The introduction of Variation 10.
This certificate and its schedules may only be reproduced in its entirety and without change. Page 7 of 10 Form 9400 Issue4
15 SPECIFIC CONDITIONS OF USE (denoted by X after the certificate number) 15.1 This equipment shall be positioned such that risk of impact to the window is low. 15.2 This equipment included some external non-metallic parts, including the outer protective coating.
Cleaning shall only be carried out with a damp cloth. 15.3 In accordance with clause 5.1 of EN 60079-1, the critical dimensions of the flamepaths are
Flamepath Flamepath Dimension (mm) IQ Sizes 1, 2 and 3 IQ Sizes 5 Gap Length Gap Length
16 ESSENTIAL HEALTH AND SAFETY REQUIREMENTS OF ANNEX II (EHSRs) The relevant EHSRs that are not addressed by the standards listed in this certificate have been identified
and individually assessed in the reports listed in Section 14.2. 17 CONDITIONS OF MANUFACTURE 17.1 The use of this certificate is subject to the Regulations Applicable to Holders of Sira Certificates. 17.2 Holders of EU-Type Examination Certificates are required to comply with the conformity to type
requirements defined in Article 13 of Directive 2014/34/EU. 17.3 When the termination facility is designed as ‘Ex e’, the following electrical strength tests shall be applied to
the termination facilities for at least 60 s and no more than 63 s as required by clause 6.1 of EN 60079-7. Test Voltage Applied Between Test Voltage Three phase terminations/case 2500 V RMS
Three phase terminations and low voltage terminations 2500 V RMS
Low voltage terminations and case 1500 V RMS Alternatively, the following electrical strength tests may be applied to the termination facilities for at least 100 ms as required by clause 7.1 of IEC/EN 60079-7.
Test Voltage Applied Between Test Voltage Three phase terminations/case 3000 V RMS
Three phase terminations and low voltage terminations 3000 V RMS
This certificate and its schedules may only be reproduced in its entirety and without change. Page 8 of 10 Form 9400 Issue4
17.4 Each enclosure shall be subjected to a routine overpressure test in accordance with the tables below for the design option and ambient temperature range stated. In all cases the pressure shall be maintained for at least 10 s as required by clause 16 of EN 60079-1. There shall be no permanent deformation or damage to the enclosure:
Equipment Test Pressure bar lbf/in2
Motor Enclosure Size 5 Gearcase/Motor Compartment IQ 70/90/95 Aluminium Alloy to BS1490. Grade: LM25M (or equivalent) 13.88 201.24 IQ 70/90/95 Motor Cover Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
13.88 201.24
Routine overpressure tests IQ (below -20°C to -50°C) to +70°C
Equipment Test Pressure
bar lbf/in2 All sizes with Deep Terminal cover fitted Certified Terminal Bung Crastin ST830FRUV/Robnor PX700/BK 16.56 240.19 Gearcase - Flameproof Terminal Bung Fitted Size 1 Gearcase/Electrical Compartment Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
This certificate and its schedules may only be reproduced in its entirety and without change. Page 9 of 10 Form 9400 Issue4
Equipment Test Pressure bar lbf/in2
Motor Loom Bush Robnor PX700/BK 23.30 337.87 Short Electrical Cover aluminium alloy to ASTM B85, Grade: A360 (or equivalent) 23.30 337.87 Size 3 Gearcase/Electrical-Terminal Comp Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
19.31 280.00
Motor loom bush Robnor PX700/BK 19.31 280.00 Short Electrical Cover Aluminium Alloy to ASTM B85, Grade: A360 (or equivalent) 19.31 280.00 Size 5 Gearcase/Electrical-Terminal Compartment Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
33.90 491.69
Terminal Cover Aluminium Alloy to ASTM B85, Grade: A360 (or equivalent) 33.90 491.69 Long Electrical Cover Aluminium Alloy to ASTM B85, Grade: A360 (or equivalent) 33.90 491.69 Long Electrical Cover Aluminium Alloy to BS1490. Grade: LM25TF (Heat Treated)(or equivalent)
33.90 491.69
Motor Loom Bush Robnor PX700/BK (size 5) 33.90 491.69 bar lbf/in2 Motor Enclosure Size 5 Gearcase/Motor Compartment IQ40 Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
18.27 264.99
Gearcase/Motor Compartment IQ 70/90/95 Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
18.27 264.99
Motor Loom Bush (IQ70/90/95 motor side, when terminal bung fitted) Robnor PX700/BK (size 5)
18.27 264.99
Gearcase/Motor Compartment IQ 91 Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
13.22 191.67
IQ 40 Motor Cover Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
18.27 264.99
IQ 70/90/95 Motor Cover Aluminium Alloy to BS1490. Grade: LM25M (or equivalent)
18.27 264.99
17.5 Each enclosure shall be subjected to a routine overpressure test in accordance with the tables below for
the design option and ambient temperature range stated. In all cases the pressure shall be maintained for at least 10 s as required by clause 16 of EN 60079-1:2007. There shall be no permanent deformation or damage to the enclosure:
Certificate Annexe Certificate Number: Sira 12ATEX1123X Equipment: IQ Range of Electric Valve Actuators Applicant: Rotork Controls
This certificate and its schedules may only be reproduced in its entirety and without change. Page 1 of 3 Form 9400 Issue4
Issue 0 Drawing Sheets Rev. Date (Sira Stamp) Title PLAD 1346 1 to 6 01 20 Aug 12 Parts List for IQ20 & 25 Actuators ATEX & IECEx Certification Group IIB
& IIC AD 1346 1 to 4 01 20 Aug 12 IQ20 & 25 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1350 1 to 6 01 20 Aug 12 Parts List for IQ10, 12 & 18 Actuators ATEX & IECEx Certification Group
IIB & IIC AD 1350 1 to 4 01 20 Aug 12 IQ10, 12 & 18 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1351 1 to 6 01 20 Aug 12 Parts List for IQ35 Actuator ATEX & IECEx Certification Group IIB & IIC AD 1351 1 to 4 01 20 Aug 12 IQ35 Actuators ATEX & IECEx Approval GRP IIB & IIC AD1399 1 to 2 1 23 Aug 12 Terminal Bung & Main Labels – IQ ATEX& IECEx IIB & IIC 44406 1 of 1 1 20 Aug 12 Label fuse types – CENELEC Battery Loom 95-462 1 to 2 2 20 Aug 02 Low Temperature Battery 95-416 1 to 2 2 20 Aug 12 High temperature Battery
Issue 1 Drawing Sheets Rev. Date (Sira Stamp) Title PLAD 1347 1 to 6 1 24 Oct 12 Parts List for IQ40,70,90,95 & 91 Actuators ATEX & IECEx Certification
Group IIB & IIC AD 1347 1 to 5 1 24 Oct 12 IQ40,70,90,95 & 91 Actuator ATEX & IECEx Approval GRP IIB & IIC AD1411 1 to 3 1 01 Nov 12 Deep Cover Housing, ATEX & IECEx Groups IIB & IIC
Issue 2 Drawing Sheets Rev. Date (Sira Stamp) Title PLAD 1346 1 to 6 02 08 Nov 12 Parts List for IQ20 & 25 Actuators ATEX & IECEx Certification Group IIB
& IIC AD 1346 1 to 5 02 08 Nov 12 IQ20 & 25 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1350 1 to 6 02 08 Nov 12 Parts List for IQ10, 12 & 18 Actuators ATEX & IECEx Certification Group
IIB & IIC AD 1350 1 to 5 02 08 Nov 12 IQ10, 12 & 18 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1351 1 to 6 02 08 Nov 12 Parts List for IQ35 Actuator ATEX & IECEx Certification Group IIB & IIC AD 1351 1 to 5 02 08 Nov 12 IQ35 Actuator ATEX & IECEx Approval GRP IIB & IIC
Issue 3 Drawing Sheets Rev. Date (Sira Stamp) Title AD1346 1 to 6 3 04 Jan 13 IQ 20 & 25 Actuators-ATEX & IECEx Approval Group IIB & IIC AD1350 1 to 6 3 04 Jan 13 IQ 10, 12 & 18 Actuators-ATEX & IECEx Approval Group IIB & IIC AD1412 1 to 2 1 25 Jan 13 IQ10-95 Intumescent Coated Actuators (ATEX, IECEx, FM & CSA) PLAD1346 1 to 6 3 04 Jan 13 PARTS LIST FOR IQ 20 & 25 Actuators-ATEX & IECEx Approval Group
IIB & IIC PLAD1350 1 to 6 3 04 Jan 13 Parts List For IQ 10, 12 & 18 Actuators-ATEX & IECEx Approval Group
IIB & IIC Issue 4 Drawing Sheets Rev. Date (Sira stamp) Title AD1423 1 to 2 1 07 Jun 13 Lightning Suppresion Module, ATEX& IECEx Approvals
Certificate Annexe Certificate Number: Sira 12ATEX1123X Equipment: IQ Range of Electric Valve Actuators Applicant: Rotork Controls
This certificate and its schedules may only be reproduced in its entirety and without change. Page 2 of 3 Form 9400 Issue4
Issue 5 Drawing Sheets Rev. Date (Sira stamp) Title PLAD 1346 1 to 7 04 28 Jul 14 Parts List for IQ20 & 25 Actuators ATEX & IECEx Certification Group
IIB & IIC AD 1346 1 to 4 04 28 Jul 14 IQ20 & 25 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1350 1 to 6 04 28 Jul 14 Parts List for IQ10, 12 & 18 Actuators ATEX & IECEx Certification
Group IIB & IIC AD 1350 1 to 6 04 28 Jul 14 IQ10, 12 & 18 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1351 1 to 6 03 28 Jul 14 Parts List for IQ35 Actuator ATEX & IECEx Certification Group IIB &
IIC AD 1351 1 to 6 03 28 Jul 14 IQ35 Actuator ATEX & IECEx Approval GRP IIB & IIC PLAD 1347 1 to 6 02 28 Jul 14 Parts List for IQ40,70,90,95 & 91 Actuators ATEX & IECEx
Certification Group IIB & IIC AD 1347 1 to 6 02 28 Jul 14 IQ40,70,90,95 & 91 Actuator ATEX & IECEx Approval GRP IIB & IIC
Issue 6 Drawing Sheets Rev. Date (Sira stamp) Description PLAD 1346 1 to 6 05 20 Aug 15 Parts List for IQ20 & 25 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD 1347 1 to 6 03 20 Aug 15 Parts List for IQ40, 70, 90, 95 & 91 Actuators ATEX & IECEx
Certification Group IIB & IIC PLAD 1350 1 to 6 05 20 Aug 15 Parts List for IQ10, 12 & 18 Actuators ATEX & IECEx
Certification Group IIB & IIC Issue 7 Drawing Sheets Rev. Date (Sira stamp) Description PLAD 1346 1 to 6 06 12 Oct 15 Parts List for IQ 19, 20 & 25 Actuators ATEX & IECEx
Certification Group IIB & IIC AD 1346 1 to 7 05 12 Oct 15 IQ 19, 20 & 25 Actuator ATEX & IECEx Approval Group IIB & IIC AD1411 1 to 3 2 12 Oct 15 Deep Cover Housing, ATEX & IECEx Group IIB &b IIC
Issue 8 Drawing Sheets Rev. Date(Sira stamp) Title PLAD1346 1 to 6 07 06 Jul 16 Parts List for IQ 19, 20 & 25 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD1347 1 to 6 04 06 Jul 16 Parts List for IQ 40, 70, 90, 95, & 91 Actuators ATEX & IECEx
Certification Group IIB & IIC PLAD1350 1 to 6 06 06 Jul 16 Parts List for IQ 10, 12 & 18 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD1351 1 to 6 04 06 Jul 16 Parts List for IQ 35Actuators ATEX & IECEx Certification Group
IIB & IIC Issue 9 Drawing Sheets Rev. Date(Sira stamp) Title AD1346 1 to 7 6 26 Sept 17 IQ19,20 & 25 Actuator ATEX & IECEx Approval Group IIB & IIC AD 1347 1 to 6 3 26 Sept 17 IQ40,70,90,95 & 91 Actuator ATEX & IECEx Approval GP IIB &
Certificate Annexe Certificate Number: Sira 12ATEX1123X Equipment: IQ Range of Electric Valve Actuators Applicant: Rotork Controls
This certificate and its schedules may only be reproduced in its entirety and without change. Page 3 of 3 Form 9400 Issue4
Drawing Sheets Rev. Date(Sira stamp) Title AD 1351 1 to 6 4 26 Sept 17 IQ35 Actuator ATEX & IECEx Approval Group IIB & IIC PLAD1346 1 to 8 08 26 Sept 17 Parts List for IQ 19, 20 & 25 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD1347 1 to 9 05 26 Sept 17 Parts List for IQ 40, 70, 90, 95, & 91 Actuators ATEX & IECEx
Certification Group IIB & IIC PLAD1350 1 to 7 07 26 Sept 17 Parts List for IQ 10, 12 & 18 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD1351 1 to 7 05 26 Sept 17 Parts List for IQ 35Actuators ATEX & IECEx Certification Group
IIB & IIC Issue 10 Drawing Sheets Rev. Date (Sira stamp) Description AD 1346 1 to 8 7 18 June 18 IQ19,20 & 25 Actuator ATEX & IECEx Approval Group IIB & IIC AD 1347 1 to 7 4 18 June 18 IQ40,70,90,95 & 91 Actuator ATEX & IECEx Approval GP IIB &
IIC AD 1350 1 to 7 6 18 June 18 IQ10, 12 & 18 Actuator ATEX & IECEx Approval GRP IIB & IIC AD 1351 1 to 7 5 18 June 18 IQ35 Actuator ATEX & IECEx Approval Group IIB & IIC AD 1399 1 to 2 2 08 May 18 Terminal Bung & Main Labels – IQ ATEX & IECEx IIB & IIC PLAD1346 1 to 8 09 08 May 18 Parts List for IQ 19, 20 & 25 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD1347 1 to 8 06 08 May 18 Parts List for IQ 40, 70, 90, 95, & 91 Actuators ATEX & IECEx
Certification Group IIB & IIC PLAD1350 1 to 8 08 08 May 18 Parts List for IQ 10, 12 & 18 Actuators ATEX & IECEx Certification
Group IIB & IIC PLAD1351 1 to 8 06 08 May 18 Parts List for IQ 35Actuators ATEX & IECEx Certification Group
![EU-TYPE EXAMINATION CERTIFICATE Stations (DEMK… · [13] Schedule [14] EU-TYPE EXAMINATION CERTIFICATE No. DEMKO 15 ATEX 1405X Rev. 1 00-IC-F0056 – Issue 14.0 This certificate](https://static.documents.pub/doc/80x56/5ece0834be5372253b669618/eu-type-examination-certificate-stations-demk-13-schedule-14-eu-type-examination.jpg)
![EU-TYPE EXAMINATION CERTIFICATE - Crowcon …11+ATEX... · [13] Schedule [14] EU-TYPE EXAMINATION CERTIFICATE No. DEMKO 11 ATEX 1031772X Rev. 5 Report: 4787317703 00-IC-F0056 –](https://static.documents.pub/doc/80x56/5aa882d07f8b9a9a188bafd8/eu-type-examination-certificate-crowcon-11atex13-schedule-14-eu-type.jpg)
![EU-TYPE EXAMINATION CERTIFICATE[13] Schedule [14] EU-TYPE EXAMINATION CERTIFICATE No. DEMKO 15 ATEX 1405X Rev. 1 00-IC-F0056 – Issue 14.0 This certificate may only be reproduced](https://static.documents.pub/doc/80x56/5e67c1c129c3d7000c41cd2a/eu-type-examination-certificate-13-schedule-14-eu-type-examination-certificate.jpg)
