UK/0126/0197

MI-006

Issue date: Valid until:

12 June 2019 20 July 2026

Grégory Glas Lead Technical Manager For and on behalf of the Head of Technical Services

0135 NMO I Stanton Avenue I Teddington I TW11 OJZ I United Kingdom

Tel +44 (0) 20 8943 7272 I Fax +44 (0) 20 8943 7270 I Web www.gov.uk/government/organisations/office-for-product-safety-and-standards NMO is part of the Office for Product Safety and Standards within the Department for Business, Energy & Industrial Strategy

EU-type examination certificate UK/0126/0197 Revision 2

Issued by:

NMO Notified Body Number 0126

In accordance with the requirements of the Measuring Instruments Regulations 2016 (S.I. 2016 No. 1153) which implement, in the United Kingdom, Council Directive 2014/32/EU, this EU-type examination certificate has been issued to:

Avery Weigh-Tronix Foundry Lane Smethwick West Midlands B66 2LP United Kingdom

In respect of an automatic gravimetric filling instrument, comprising of a weighing controller designated the Avery Weigh-Tronix ZM505 / ZM510 / ZM605 / ZM615 Series, a material feed mechanism, and a weighing unit comprising a load receptor and associated load cell(s) and having the following characteristics: Reference accuracy class: Ref (x) = 0.05 (ZM505, ZM510 Standard build and when

fitted with 10V EXC load cell option card(s)) Ref (x) = 0.05 (ZM605, ZM615 Standard build and when

fitted with 10V EXC load cell option card(s)) Ref (x) = 0.1 (5V EXC load cell option card) Maximum capacity: Dependent upon load cell(s) specification Minimum load: Dependent upon operating accuracy class X(x)

Scale interval 0.5 g

Number of scale intervals 10 000 (ZM505, ZM510, ZM605, ZM615 and 10V EXC load cell option card)

6 000 (5V EXC load cell option card)

The necessary data (principal characteristics, alterations, securing, functioning etc) for identification purposes and conditions (when applicable) are set out in the descriptive annex to this certificate.

This revision replaces previous versions of the certificate.

2/10

Descriptive Annex

1 INTRODUCTION This pattern of an automatic gravimetric filling instrument for dispensing predetermined loads of powdered, granular or liquid materials consists of a feeding device, a weighing unit, and a ZM505 / ZM510 / ZM605 / ZM615 weighing controller (Figures 1-8). 2 FUNCTIONAL DESCRIPTION

2.1 Mechanical

The instrument comprises material handling facilities (feeding device and weighing unit) which shall enable it to respect the MPEs during normal operation. 2.1.1 Material feeding device The feeding device may be any one of the following:

− Gravity feeder

− Gravity feeder with agitator

− Single screw or double screw feeder

− Belt feeder

− Vibratory feeder

2.1.2 Weighing unit The weighing unit is either a load receptor incorporating a weigh hopper and associated discharge device for weighing of target weights in the weigh hopper (net weighing), or a load receptor without a discharge device for weighing directly into containers (gross weighing). 2.1.3 Load cell(s) Any compatible load cell(s) may be used providing the following conditions are met:

− There is a respective OIML Certificate of Conformity (R60) or a Parts (Test) Certificate (EN45501) issued for the load cell by a Notified Body responsible for type examination under Directive 2014/31/EU.

− The certificate contains the load cell types and the necessary load cell data required for the manufacturer's declaration of compatibility of modules (WELMEC 2, 2015, No 10), and any particular installation requirements. A load cell marked NH is allowed only if humidity testing to EN45501 has been conducted on this load cell.

− The compatibility of load cells and indicator is established by the manufacturer by means of the compatibility of modules form, contained in the above WELMEC 2 document.

− The load transmission conforms to one of the examples detailed in WELMEC Guide 2.4, “Guide for Load Cells”.

3/10

3 TECHNICAL DATA

The technical data and software information for the ZM505 / ZM510 / ZM605 / ZM615 weighing controller is as described in Evaluation Certificate GB-1577.

4 PERIPHERAL DEVICES AND INTERFACES

4.1 Interfaces

The instrument may be fitted with the following protected interfaces (fully described in Evaluation Certificate GB-1577):

− Load cell 4-wire or 6-wire shielded connection − Logic level inputs − Open collector outputs − Analogue outputs − Current Loop − RS232/422/485 − 10/100 Ethernet − USB Host − Wireless LAN 802.11b/g − USB Device − Bluetooth − DeviceNet − Profibus − Power over Ethernet − DC inputs − DC outputs − AC inputs − AC outputs − GSE & 1310 legacy interfaces − Programmable Digital I/O interfaces

4.2 Peripheral devices

The instrument may be connected to any peripheral device that has been issued with Parts Certificate by a Notified Body responsible for Module B under Directive 2014/32/EU and bears the CE marking of conformity to the relevant directives; or A peripheral device without a Parts certificate may be connected under the following conditions:

− it bears the CE marking for conformity to the EMC Directive;

− it is not capable of transmitting any data or instruction into the measuring instrument, other than to release a printout, checking for correct data transmission or validation;

− it prints measurement results and other data as received from the measuring instrument without any modification or further processing; and

− it complies with the applicable requirements of Paragraph 8.1 of Annex I.

5 APPROVAL CONDITIONS

The certificate is issued subject to the following conditions:

4/10

5.1 Inscriptions

The instrument shall bear the following inscriptions:

- CE marking - Supplementary metrology marking - Manufacturer’s name, registered trade name or registered trade mark and

postal address - Identification number of the notified body - Information in respect of its accuracy

and, when applicable:

- Information in respect of the conditions of use - Measuring capacity - Identity marking (a type, batch or serial number or other element allowing their

identification) - Number of the EU-type examination certificate - Information whether or not additional devices providing metrological results

comply with the provisions of Directive 2014/32/EU on legal metrological control

The markings and inscriptions shall fulfil the requirements of Article 8, Article 21, Article 22 and Point 9 of Annex I of Directive 2014/32/EU.

5.2 The instrument shall be permanently installed or shall be provided with a level indicator. 5.3 The ZM505 and ZM510 instruments (including 10V EXC load cell option card) shall be set to zero at least every 16 min, while the ZM505 and ZM510 instruments if fitted with a 5V EXC load cell option card shall be set to zero at least every 15 min, via semi-automatic zero-setting, zero-tracking or tare devices. 5.4 The ZM605 and ZM615 instruments (including 10V EXC load cell option card) shall be set to zero at least every 2 hours 30 minutes, while the ZM605 and ZM615 instruments if fitted with a 5V EXC load cell option card shall be set to zero at least every 15 min, via semi-automatic zero-setting, zero-tracking or tare devices. 6 LOCATION OF SEALS AND VERIFICATION MARKS

6.1 The ‘CE’ mark shall be impossible to remove without damaging it. The rating plate shall be impossible to remove without it being destroyed.

6.2 Components that may not be dismantled or adjusted by the user (jumper on main board when applicable, load cell connection) must be secured. Common serial numbers, a wire and seal solution or a tamper-evident sticker (bearing a securing mark) may be used. The securing mark may be either:

− a mark of the manufacturer and/or manufacturer’s representative, or

− an official mark of a verification officer.

6.3 When software sealing is used, the CONFIG and CAL counters’ values shall be written on a tamper-evident label on or near the rating plate.

5/10

7 ALTERNATIVES 7.1 The indicator may be connected to Avery Weigh-Tronix ZB210 digital junction boxes to form an automatic gravimetric filling instrument, Ref(x) = 0.1. The ZB210 digital junction boxes are fully described in Parts Certificate GB-1656.

8 ILLUSTRATIONS

Figure 1 ZM505-SD3 weighing controller Figure 2 ZM505-SP3 weighing controller Figure 3 ZM510-SD4 weighing controller Figure 4 ZM510-SP4 weighing controller Figure 5 ZM605-SD4 weighing controller Figure 6 ZM605-SP4 weighing controller Figure 7 ZM615-SD5 weighing controller Figure 8 ZM615-SP5 weighing controller Figure 9 Rating plate example – AC Voltage Figure 10 Rating plate example – DC Voltage CERTIFICATE HISTORY

ISSUE NO. DATE DESCRIPTION

UK/0126/0197 21 July 2016 Type-examination certificate first issued.

UK/0126/0197 Revision 1

12 October 2017 Wording in 5.1 updated to reflect 2014/32/EU.

Addition of ZM505 / ZM605 / ZM615 series.

“Programmable Digital I/O” added to 4.1.

Renumbering and addition of figures to reflect additional models in the range.

UK/0126/0197 Revision 2

12 June 2019 Added Alternative 7.1

6/10

Figure 1 ZM505-SD3 weighing controller

Figure 2 ZM505-SP3 weighing controller

7/10

Figure 3 ZM510-SD4 weighing controller

Figure 4 ZM510-SP4 weighing controller

8/10

Figure 5 ZM605-SD4 weighing controller

Figure 6 ZM605-SP4 weighing controller

9/10

Figure 7 ZM615-SD5 weighing controller

Figure 8 ZM615-SP5 weighing controller

10/10

Figure 9 Rating plate example – AC Voltage

Figure 10 Rating plate example – DC Voltage © Crown copyright 2019 NMO Office for Product Safety and Standards Department for Business, Energy & Industrial Strategy This material may be freely reproduced except for sale