20
2011/2012 PURE LED
| Date post: | 23-Mar-2016 |
| Category: |
Documents |
| Upload: | add-lighting-pty-ltd |
| View: | 217 times |
| Download: | 3 times |
2011/2012p u r e l e d
Because we design and manufacture the current control
circuitry in our luminaires and light engines, we have
the ability to decrease the drive current in response to
inevitable industry improvements to the efficiencies of
the LEDs. This allows us to easily maintain constant
brightness levels within a product line from year to
year. If a luminaire is damaged or our client expands
their space and additional luminaires are required, we
can provide new luminaires that produce the same light
output as the ones installed previously.
Future Proofing
At this time, there are no unified standards for the
manufacturing of LEDs and debate is ongoing as to the
proper ways to test them for brightness, color quality, and
lifetime. At Eulum Design we test all of our luminaires and
LED light engines to ANSI (American National Standards
Institute) standard LM79. This standard defines the latest
industry-approved guidelines to test the true output of the
luminaire both in total circuit efficacy and lumen output by
an independent laboratory.
What are the standards for LEDs?
All Eulum Design luminaires comply fully to EN60598-1 and are tested to ANSI LM79.
Eulum Design is an ISO9001 registered firm.
Eulum Design takes it’s ecological responsibilities seriously and as such we:
Lead free solder in compliance with RoHS requirements
All Aluminium used has a minimum 20% recycled element
All packaging is recyclable
No harmful solvents are used and where possible the use of solvents is avoided
Off the shelf constant current power supplies can be
very inefficient as they are designed to operate over a wide
range of LED configurations. The datasheets for these
devices often will show an efficiency specification at the
best possible operating condition, while the efficiency for
your particular LED configuration could be below 70%.
Eulum Design optimizes each on-board driver for the LED
load it is designed to drive, often reaching efficiencies as
high as 97%.
Our on-board current control circuitry is designed to
operate from a standard 24VDC supply that allows simple
and efficient power distribution using thousands of readily
available power supplies from hundreds of suppliers
across the world.
The on-board driver allows our designs to directly
monitor the temperature of the LEDs, and make
adjustments to the current control to ensure a long
lifetime, even under fault conditions such as an
undersized heatsink.
What makes Eulum Design Special?
EU-D46/1-M80
Ø46mm LED Module
Designed for ease of installation the EU-D46/1-M80 is the ultimate 1,000lm single point source LED engine, with the most advanced features:
• 24vDC constant voltage input.
• 0-10v Dimming input direct on-board
• Thermal protection of the diode via feed back circuit which will reduce the current by 1% for each 1°C increase over 70°C measured on the substrate so as to ensure the life of the LED.
• Aluminium dielectric substrate to provide better ‘heat spreading’ with superior thermal resistance to standard aluminium PCB’s.
• A die-cut thermal transfer material is available to create optimum thermal transfer from the LED module to the heat sink.
• Secondary optics available for 15° and 30° beam angles.
• Independently tested to ANSI LM79
• Replacement for 26w TCDE & 20w HIT
EU-45x42/3-M80
45x42mm LED Module
Designed for ease of installation the EU-45x42/3-M80 is the ultimate 3,000lm LED engine, with the most advanced features:
• 0-10v Dimming input direct on-board
• Thermal protection of the diode via feed back circuit which will reduce the current by 1% for each 1°C increase over 70°C measured on the substrate so as to ensure the life of the LED.
• Aluminium dielectric substrate to provide better ‘heat spreading’ with superior thermal resistance to standard aluminium PCB’s.
• A die-cut thermal transfer material is available to create optimum thermal transfer from the LED module to the heat sink.
• Independently tested to ANSI LM79
• Replacement for 2x26w TCDE & 35w HIT
EU-D216/96L
254x203mm LED Module
Designed for ease of installation the EU-D216/96L is the ultimate retrofit LED engine, with the most advanced features:
• 90-230vAC input.
• Triac Dimming or 0-10v Dimming options
• Remote 90min or 3hr Emergency kit available
• 4 layer FR4 substrate with heat spreaders on top and bottom
• Isolating base in white PC and transparent PC cover (optional)
• Uniformly even lit appearance
• Independently tested to ANSI LM79
• Replacement for 28w TCDDE & 26w TCDE
EU-483x20/84 | EU-483x20/42
483x20mm LED Module
Designed for ease of installation the EU-483x20 range of linear LED boards, with thermal transfer tape applied for maximum thermal transfer.
• Independently tested to ANSI LM79
• Replacement for T5 fluorescent lamps
Eulum Design was established in 2002 and then
incorporated in 2005 with the sole intention to design,
manufacture & supply the highest quality and the most
innovative luminaires at the most competitive prices. Today
we are one of the leading manufacturers of low energy LED
Lighting products and components, supplying bespoke
systems all over the world.
Our unique approach to drive circuitry and the thermal
control of the diode, enables Eulum Design to offer the
most efficient LED modules that will ensure optimum
performance throughout their life cycle.
Eulum Design’s innovative dimming control devices
will allow our customers total flexibility along with full
integration into existing installations previously designed for
tungsten or fluorescent luminaries.
UK & USA Design and Manufacturing
Highest quality components
Highly experienced professionals
Introduction
3
Because we design and manufacture the current control
circuitry in our luminaires and light engines, we have
the ability to decrease the drive current in response to
inevitable industry improvements to the efficiencies of
the LEDs. This allows us to easily maintain constant
brightness levels within a product line from year to
year. If a luminaire is damaged or our client expands
their space and additional luminaires are required, we
can provide new luminaires that produce the same light
output as the ones installed previously.
Future Proofing
At this time, there are no unified standards for the
manufacturing of LEDs and debate is ongoing as to the
proper ways to test them for brightness, color quality, and
lifetime. At Eulum Design we test all of our luminaires and
LED light engines to ANSI (American National Standards
Institute) standard LM79. This standard defines the latest
industry-approved guidelines to test the true output of the
luminaire both in total circuit efficacy and lumen output by
an independent laboratory.
What are the standards for LEDs?
All Eulum Design luminaires comply fully to EN60598-1 and are tested to ANSI LM79.
Eulum Design is an ISO9001 registered firm.
Eulum Design takes it’s ecological responsibilities seriously and as such we:
Lead free solder in compliance with RoHS requirements
All Aluminium used has a minimum 20% recycled element
All packaging is recyclable
No harmful solvents are used and where possible the use of solvents is avoided
Off the shelf constant current power supplies can be
very inefficient as they are designed to operate over a wide
range of LED configurations. The datasheets for these
devices often will show an efficiency specification at the
best possible operating condition, while the efficiency for
your particular LED configuration could be below 70%.
Eulum Design optimizes each on-board driver for the LED
load it is designed to drive, often reaching efficiencies as
high as 97%.
Our on-board current control circuitry is designed to
operate from a standard 24VDC supply that allows simple
and efficient power distribution using thousands of readily
available power supplies from hundreds of suppliers
across the world.
The on-board driver allows our designs to directly
monitor the temperature of the LEDs, and make
adjustments to the current control to ensure a long
lifetime, even under fault conditions such as an
undersized heatsink.
What makes Eulum Design Special?
EU-D46/1-M80
Ø46mm LED Module
Designed for ease of installation the EU-D46/1-M80 is the ultimate 1,000lm single point source LED engine, with the most advanced features:
• 24vDC constant voltage input.
• 0-10v Dimming input direct on-board
• Thermal protection of the diode via feed back circuit which will reduce the current by 1% for each 1°C increase over 70°C measured on the substrate so as to ensure the life of the LED.
• Aluminium dielectric substrate to provide better ‘heat spreading’ with superior thermal resistance to standard aluminium PCB’s.
• A die-cut thermal transfer material is available to create optimum thermal transfer from the LED module to the heat sink.
• Secondary optics available for 15° and 30° beam angles.
• Independently tested to ANSI LM79
• Replacement for 26w TCDE & 20w HIT
EU-45x42/3-M80
45x42mm LED Module
Designed for ease of installation the EU-45x42/3-M80 is the ultimate 3,000lm LED engine, with the most advanced features:
• 0-10v Dimming input direct on-board
• Thermal protection of the diode via feed back circuit which will reduce the current by 1% for each 1°C increase over 70°C measured on the substrate so as to ensure the life of the LED.
• Aluminium dielectric substrate to provide better ‘heat spreading’ with superior thermal resistance to standard aluminium PCB’s.
• A die-cut thermal transfer material is available to create optimum thermal transfer from the LED module to the heat sink.
• Independently tested to ANSI LM79
• Replacement for 2x26w TCDE & 35w HIT
EU-D216/96L
254x203mm LED Module
Designed for ease of installation the EU-D216/96L is the ultimate retrofit LED engine, with the most advanced features:
• 90-230vAC input.
• Triac Dimming or 0-10v Dimming options
• Remote 90min or 3hr Emergency kit available
• 4 layer FR4 substrate with heat spreaders on top and bottom
• Isolating base in white PC and transparent PC cover (optional)
• Uniformly even lit appearance
• Independently tested to ANSI LM79
• Replacement for 28w TCDDE & 26w TCDE
EU-483x20/84 | EU-483x20/42
483x20mm LED Module
Designed for ease of installation the EU-483x20 range of linear LED boards, with thermal transfer tape applied for maximum thermal transfer.
• Independently tested to ANSI LM79
• Replacement for T5 fluorescent lamps
Eulum Design was established in 2002 and then
incorporated in 2005 with the sole intention to design,
manufacture & supply the highest quality and the most
innovative luminaires at the most competitive prices. Today
we are one of the leading manufacturers of low energy LED
Lighting products and components, supplying bespoke
systems all over the world.
Our unique approach to drive circuitry and the thermal
control of the diode, enables Eulum Design to offer the
most efficient LED modules that will ensure optimum
performance throughout their life cycle.
Eulum Design’s innovative dimming control devices
will allow our customers total flexibility along with full
integration into existing installations previously designed for
tungsten or fluorescent luminaries.
UK & USA Design and Manufacturing
Highest quality components
Highly experienced professionals
Introduction
3
Koya-S1|P1 LED Koya-R2 LED
5
Koya-S1|P1 Surface & Pendant mounted LED luminaire
Suitable for wall or ceiling mounting
Pendant length 1500mm
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
D H Lamps Luminaire Efficacy
lm/w
CRI Code Code
Koya-S1 silver white
300 75 14w LED 49 80+ KS1OSIG-1-R01-WW KS1OWIG-1-R01-WW
300 75 14w LED 55 80+ KS1OSIG-1-R01-NW KS1OWIG-1-R01-NW
Koya-P1 silver white
300 75 14w LED 49 80+ KP1OSIG-1-R01-WW KP1OWIG-1-R01-WW
300 75 14w LED 55 80+ KP1OSIG-1-R01-NW KP1OWIG-1-R01-NW
Koya-R2 Plaster-In recessed mounted LED luminaire Suitable for trimless installation in plasterboard ceilings 8-16 mm
Luminaire body made of white coated or anodised extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
D1 D2 Lamps Luminaire Efficacy
lm/w
CRI Code
white
300 316 14w LED 49 80+ KR2OWIG-1-R01-WW
300 316 14w LED 55 80+ KR2OWIG-1-R01-NW
D2
min 10mm
30
100max 20mm
EVG
D1
D2
D
75
60
max1500
D
H
Koya-S1|P1 LED Koya-R2 LED
5
Koya-S1|P1 Surface & Pendant mounted LED luminaire
Suitable for wall or ceiling mounting
Pendant length 1500mm
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
D H Lamps Luminaire Efficacy
lm/w
CRI Code Code
Koya-S1 silver white
300 75 14w LED 49 80+ KS1OSIG-1-R01-WW KS1OWIG-1-R01-WW
300 75 14w LED 55 80+ KS1OSIG-1-R01-NW KS1OWIG-1-R01-NW
Koya-P1 silver white
300 75 14w LED 49 80+ KP1OSIG-1-R01-WW KP1OWIG-1-R01-WW
300 75 14w LED 55 80+ KP1OSIG-1-R01-NW KP1OWIG-1-R01-NW
Koya-R2 Plaster-In recessed mounted LED luminaire Suitable for trimless installation in plasterboard ceilings 8-16 mm
Luminaire body made of white coated or anodised extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
D1 D2 Lamps Luminaire Efficacy
lm/w
CRI Code
white
300 316 14w LED 49 80+ KR2OWIG-1-R01-WW
300 316 14w LED 55 80+ KR2OWIG-1-R01-NW
D2
min 10mm
30
100max 20mm
EVG
D1
D2
D
75
60
max1500
D
H
Iza-S2|P2 LED
7
Koya-O1|P2 LED
Koya-O1|P2 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Diffuser from Opal Acryl-Satiné with silver/grey coated ‘contrast’ fixing ring 90-230vAC Input with Triac dimming
Iza-S2|P2 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Luminaire body made of white oe silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
D H Lamps Luminaire Efficacy
lm/w
CRI Code
Koya-O1 silver
400 75 14w LED 49 80+ KO1OSIG-1-R01-WW
400 75 14w LED 58 80+ KO1OSIG-1-R01-NW
Koya-P2 silver
400 75 14w LED 49 80+ KP2OSIG-1-R01-WW
400 75 14w LED 58 80+ KP2OSIG-1-R01-NW
L H Lamps Luminaire Efficacy
lm/w
CRI Code
Iza-S2 silver
300 75 14w LED 49 80+ IS2OEIG-1-R01-WW
300 75 14w LED 55 80+ IS2OEIG-1-R01-NW
Iza-P2 silver
300 75 14w LED 49 80+ IP2OEIG-1-R01-WW
300 75 14w LED 55 80+ IP2OEIG-1-R01-NW
D
75
60
max1500
D
75
min 70
L2
H
max1500
L1
L1
H L
L
5,5
Iza-S2|P2 LED
7
Koya-O1|P2 LED
Koya-O1|P2 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Diffuser from Opal Acryl-Satiné with silver/grey coated ‘contrast’ fixing ring 90-230vAC Input with Triac dimming
Iza-S2|P2 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Luminaire body made of white oe silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
D H Lamps Luminaire Efficacy
lm/w
CRI Code
Koya-O1 silver
400 75 14w LED 49 80+ KO1OSIG-1-R01-WW
400 75 14w LED 58 80+ KO1OSIG-1-R01-NW
Koya-P2 silver
400 75 14w LED 49 80+ KP2OSIG-1-R01-WW
400 75 14w LED 58 80+ KP2OSIG-1-R01-NW
L H Lamps Luminaire Efficacy
lm/w
CRI Code
Iza-S2 silver
300 75 14w LED 49 80+ IS2OEIG-1-R01-WW
300 75 14w LED 55 80+ IS2OEIG-1-R01-NW
Iza-P2 silver
300 75 14w LED 49 80+ IP2OEIG-1-R01-WW
300 75 14w LED 55 80+ IP2OEIG-1-R01-NW
D
75
60
max1500
D
75
min 70
L2
H
max1500
L1
L1
H L
L
5,5
Iza-R2 LED Iza-O1 LED
9
Iza-R2 Plaster-In recessed mounted LED luminaire Suitable for trimless installation in plasterboard ceilings 8-16 mm
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
Iza-O1 Surface mounted LED luminaire Suitable for wall or ceiling mounting
Diffuser from Opal Acryl-Satiné with silver/grey coated ‘contrast’ strap 90-230vAC Input with Triac dimming
A C1 C2 Lamps Luminaire Efficacy
lm/w
CRI Code
silver
340 365 344 14w LED 49 80+ IR2OEIG-1-R01-WW
340 365 344 14w LED 55 80+ IR2OEIG-1-R01-NW
L H Lamps Luminaire Efficacy
lm/w
CRI Code
silver
300 75 14w LED 49 80+ IO1OSIG-1-R01-WW
300 75 14w LED 58 80+ IO1OSIG-1-R01-NW
EVG
C1A
C2
107
max 35mm
min 10mm
30
C1 × C2
H L
L
Iza-R2 LED Iza-O1 LED
9
Iza-R2 Plaster-In recessed mounted LED luminaire Suitable for trimless installation in plasterboard ceilings 8-16 mm
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming
Iza-O1 Surface mounted LED luminaire Suitable for wall or ceiling mounting
Diffuser from Opal Acryl-Satiné with silver/grey coated ‘contrast’ strap 90-230vAC Input with Triac dimming
A C1 C2 Lamps Luminaire Efficacy
lm/w
CRI Code
silver
340 365 344 14w LED 49 80+ IR2OEIG-1-R01-WW
340 365 344 14w LED 55 80+ IR2OEIG-1-R01-NW
L H Lamps Luminaire Efficacy
lm/w
CRI Code
silver
300 75 14w LED 49 80+ IO1OSIG-1-R01-WW
300 75 14w LED 58 80+ IO1OSIG-1-R01-NW
EVG
C1A
C2
107
max 35mm
min 10mm
30
C1 × C2
H L
L
Utsu-S2 LED Utsu-R2|R3 LED
11
Utsu-S2 Surface mounted LED luminaire Suitable for wall or ceiling mounting
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from microprismatic screen / Opal Acryl-Satiné 90-230vAC Input with Triac dimming
Utsu-R2|R3 Plaster-In recessed mounted LED luminaire Suitable for trimless installation in plasterboard ceilings 8-16 mm
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming Custom lengths and systems upon request
L H Lamps Luminaire Efficacy
lm/w
CRI Code Code
silver white
300 75 14w LED 49 80+ US2OSIG-1-R01-WW US2OWIG-1-R01-WW
300 75 14w LED 55 80+ US2OSIG-1-R01-NW US2OWIG-1-R01-NW
A H Lamps Luminaire Efficacy
lm/w
CRI Code
Utsu-R2 white
260 100 14w LED 49 80+ UR2OEIG-1-R01-WW
260 100 14w LED 55 80+ UR2OEIG-1-R01-NW
L1 L2 Lamps Luminaire Efficacy
lm/w
CRI Code Code
Utsu-R3 3000K 4000K
970 971 30w LED 50 80+ UR3OEIG-2-L03-WW UR3OEIG-2-L03-NW
1455 1456 44w LED 50 80+ UR3OEIG-3-L03-WW UR3OEIG-3-L03-NW
2420 2421 72w LED 50 80+ UR3OEIG-5-L03-WW UR3OEIG-5-L03-NW
min 10mm
30
100max 20mm
EVG
A
H L
L
5,5
EVG
55
56
max
=140
mm
min=8mm
max=16mm 75
L1
L2
100
56 × L2
Utsu-S2 LED Utsu-R2|R3 LED
11
Utsu-S2 Surface mounted LED luminaire Suitable for wall or ceiling mounting
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from microprismatic screen / Opal Acryl-Satiné 90-230vAC Input with Triac dimming
Utsu-R2|R3 Plaster-In recessed mounted LED luminaire Suitable for trimless installation in plasterboard ceilings 8-16 mm
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné 90-230vAC Input with Triac dimming Custom lengths and systems upon request
L H Lamps Luminaire Efficacy
lm/w
CRI Code Code
silver white
300 75 14w LED 49 80+ US2OSIG-1-R01-WW US2OWIG-1-R01-WW
300 75 14w LED 55 80+ US2OSIG-1-R01-NW US2OWIG-1-R01-NW
A H Lamps Luminaire Efficacy
lm/w
CRI Code
Utsu-R2 white
260 100 14w LED 49 80+ UR2OEIG-1-R01-WW
260 100 14w LED 55 80+ UR2OEIG-1-R01-NW
L1 L2 Lamps Luminaire Efficacy
lm/w
CRI Code Code
Utsu-R3 3000K 4000K
970 971 30w LED 50 80+ UR3OEIG-2-L03-WW UR3OEIG-2-L03-NW
1455 1456 44w LED 50 80+ UR3OEIG-3-L03-WW UR3OEIG-3-L03-NW
2420 2421 72w LED 50 80+ UR3OEIG-5-L03-WW UR3OEIG-5-L03-NW
min 10mm
30
100max 20mm
EVG
A
H L
L
5,5
EVG
55
56
max
=140
mm
min=8mm
max=16mm 75
L1
L2
100
56 × L2
Utsu-S3|P3 LED Sienna-R1 LED
13
Utsu-S3|P3 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from microprismatic screen / Opal Acryl-Satiné Remote 24vDC power supply required Custom lengths and systems upon request
Sienna-R1 Recessed-Mounted high output LED downlight
Suitable for mounting in ceiling tiles or plasterboard, 10-30mm
Luminaire body made of die-cast Aluminium
Optical system with interchangeable glass accessories
Thermal control via ‘Coliseum’ Heat Sink and Synjet cooler
On-board Active thermal feed back to reduce the drive current in the event of overheating
0-10v Dimming Input
Remote 24vDC Power Supply
L1 Lamps Luminaire Efficacy
lm/w
CRI Code Code
Utsu-S3 3000K 4000K
970 30w LED 50 80+ US3OSIG-2-L03-WW US3OWIG-2-L03-NW
1455 44w LED 50 80+ US3OSIG-3-L03-WW US3OWIG-3-L03-NW
2420 72w LED 50 80+ US3OSIG-5-L03-WW US3OWIG-5-L03-NW
Utsu-P3 3000K 4000K
970 30w LED 57 80+ UP3OSIG-2-L03-WW UP3OWIG-2-L03-NW
1455 44w LED 57 80+ UP3OSIG-3-L03-WW UP3OWIG-3-L03-NW
2420 72w LED 57 80+ UP3OSIG-5-L03-WW UP3OWIG-5-L03-NW
Lamps Luminaire Efficacy
lm/w
CRI Code
White
40w LED 54 80+ SIRWRG-1-P03-WW
40w LED 58 80+ SIRWRG-1-P03-NW
min 70L2
55
75
max1500
L1
100L2
55
75
L1
Utsu-S3|P3 LED Sienna-R1 LED
13
Utsu-S3|P3 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from microprismatic screen / Opal Acryl-Satiné Remote 24vDC power supply required Custom lengths and systems upon request
Sienna-R1 Recessed-Mounted high output LED downlight
Suitable for mounting in ceiling tiles or plasterboard, 10-30mm
Luminaire body made of die-cast Aluminium
Optical system with interchangeable glass accessories
Thermal control via ‘Coliseum’ Heat Sink and Synjet cooler
On-board Active thermal feed back to reduce the drive current in the event of overheating
0-10v Dimming Input
Remote 24vDC Power Supply
L1 Lamps Luminaire Efficacy
lm/w
CRI Code Code
Utsu-S3 3000K 4000K
970 30w LED 50 80+ US3OSIG-2-L03-WW US3OWIG-2-L03-NW
1455 44w LED 50 80+ US3OSIG-3-L03-WW US3OWIG-3-L03-NW
2420 72w LED 50 80+ US3OSIG-5-L03-WW US3OWIG-5-L03-NW
Utsu-P3 3000K 4000K
970 30w LED 57 80+ UP3OSIG-2-L03-WW UP3OWIG-2-L03-NW
1455 44w LED 57 80+ UP3OSIG-3-L03-WW UP3OWIG-3-L03-NW
2420 72w LED 57 80+ UP3OSIG-5-L03-WW UP3OWIG-5-L03-NW
Lamps Luminaire Efficacy
lm/w
CRI Code
White
40w LED 54 80+ SIRWRG-1-P03-WW
40w LED 58 80+ SIRWRG-1-P03-NW
min 70L2
55
75
max1500
L1
100L2
55
75
L1
Delos-R1|R2 LED Eva-T1|T2 LED
15
Delos-R1|R2 Recessed-Mounted LED downlight Suitable for mounting in ceiling tiles or plasterboard, 10-30mm
Plaster-In and Directional variants Luminaire body made of machined Aluminium, thermal alloy 6063 Thermal control via Pin Heat Sink On-board Active thermal feed back to reduce the drive current in the event of overheating 0-10v Dimming Input Remote 24vDC Power Supply
Eva-T1|T2 Track mounted LED spotlight Suitable universal 3 circuit track mounting
Luminaire body made of white coated extruded / cast aluminium Interchangeable glass cover 20° and 40° optics Integral 24vDC power supply required Thermal control via Pin Heat Sink On-board Active thermal feed back to reduce the drive current in the event of overheating 0-10v Dimming Input
Lamps Luminaire Efficacy
lm/w
CRI Beam Code Code
Eva-T1 silver white
13w LED 62 83+ 20° ET1ASIG-1-P01-WW ET1AWIG-1-P01-WW
13w LED 69 83+ 20° ET1ASIG-1-P01-NW ET1AWIG-1-P01-NW
13w LED 62 83+ 40° ET1BSIG-1-P01-WW ET1BWIG-1-P01-WW
13w LED 69 83+ 40° ET1BSIG-1-P01-NW ET1BWIG-1-P01-NW
Eva-T2 silver white
34w LED 59 83+ 20° ET2ASIG-1-P01-WW ET2AWIG-1-P01-WW
34w LED 65 83+ 20° ET2ASIG-1-P01-NW ET2AWIG-1-P01-NW
34w LED 59 83+ 40° ET2BSIG-1-P01-WW ET2BWIG-1-P01-WW
34w LED 65 83+ 40° ET2BSIG-1-P01-NW ET2BWIG-1-P01-NW
Lamps Luminaire Efficacy
lm/w
CRI Code
Delos-R1 White
10w LED 65 80+ DERWRG-1-P01-WW
10w LED 70 80+ DERWRG-1-P01-NW
Delos-R1 White
10w LED 65 80+ DER1WRG-1-P01-WW
10w LED 70 80+ DER1WRG-1-P01-NW
Delos-R1|R2 LED Eva-T1|T2 LED
15
Delos-R1|R2 Recessed-Mounted LED downlight Suitable for mounting in ceiling tiles or plasterboard, 10-30mm
Plaster-In and Directional variants Luminaire body made of machined Aluminium, thermal alloy 6063 Thermal control via Pin Heat Sink On-board Active thermal feed back to reduce the drive current in the event of overheating 0-10v Dimming Input Remote 24vDC Power Supply
Eva-T1|T2 Track mounted LED spotlight Suitable universal 3 circuit track mounting
Luminaire body made of white coated extruded / cast aluminium Interchangeable glass cover 20° and 40° optics Integral 24vDC power supply required Thermal control via Pin Heat Sink On-board Active thermal feed back to reduce the drive current in the event of overheating 0-10v Dimming Input
Lamps Luminaire Efficacy
lm/w
CRI Beam Code Code
Eva-T1 silver white
13w LED 62 83+ 20° ET1ASIG-1-P01-WW ET1AWIG-1-P01-WW
13w LED 69 83+ 20° ET1ASIG-1-P01-NW ET1AWIG-1-P01-NW
13w LED 62 83+ 40° ET1BSIG-1-P01-WW ET1BWIG-1-P01-WW
13w LED 69 83+ 40° ET1BSIG-1-P01-NW ET1BWIG-1-P01-NW
Eva-T2 silver white
34w LED 59 83+ 20° ET2ASIG-1-P01-WW ET2AWIG-1-P01-WW
34w LED 65 83+ 20° ET2ASIG-1-P01-NW ET2AWIG-1-P01-NW
34w LED 59 83+ 40° ET2BSIG-1-P01-WW ET2BWIG-1-P01-WW
34w LED 65 83+ 40° ET2BSIG-1-P01-NW ET2BWIG-1-P01-NW
Lamps Luminaire Efficacy
lm/w
CRI Code
Delos-R1 White
10w LED 65 80+ DERWRG-1-P01-WW
10w LED 70 80+ DERWRG-1-P01-NW
Delos-R1 White
10w LED 65 80+ DER1WRG-1-P01-WW
10w LED 70 80+ DER1WRG-1-P01-NW
Aono-F1 LED Aono-S1|P1 LED
17
Aono-F1 Desk mounted LED luminaire Base or clamp mounting
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné Integral 24vDC power supply required Custom lengths and systems upon request
Aono-S1|P1 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné Remote 24vDC power supply required Custom lengths and systems upon request
L Lamps Luminaire Efficacy
lm/w
CRI Code
silver
700 15w LED 48 80+ AF1FEIG-1-L03-WWG
700 15w LED 53 80+ AF1FEIG-1-L03-NWG
700 15w LED 48 80+ AF1FEIG-1-L03-WWT
700 15w LED 53 80+ AF1FEIG-1-L03-NWT
L1 L2 lamps Luminaire Efficacy
lm/w
CRI Code
silver
1760 1470 44w LED 50 80+ AS1OERG-3-L03-WW
1760 1470 44w LED 57 80+ AS1OERG-3-L03-NW
1500 550 44w LED 50 80+ AP1OERG-3-L03-WW
1500 550 44w LED 57 80+ AP1OERG-3-L03-NW
70
L2
38 L1
38
50
L2
38
38
L1
DL
DLDL
1-Längig I 1-Length:
L1
1200/1500
2-Längig I 2-Length:
.
min 20mmmax 60mm
3939
320
50
38
308
460
155
L
L
Aono-F1 LED Aono-S1|P1 LED
17
Aono-F1 Desk mounted LED luminaire Base or clamp mounting
Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné Integral 24vDC power supply required Custom lengths and systems upon request
Aono-S1|P1 Surface & Pendant mounted LED luminaire Suitable for wall or ceiling mounting
Pendant length 1500mm Luminaire body made of white or silver/grey coated extruded aluminium Diffuser from Opal Acryl-Satiné Remote 24vDC power supply required Custom lengths and systems upon request
L Lamps Luminaire Efficacy
lm/w
CRI Code
silver
700 15w LED 48 80+ AF1FEIG-1-L03-WWG
700 15w LED 53 80+ AF1FEIG-1-L03-NWG
700 15w LED 48 80+ AF1FEIG-1-L03-WWT
700 15w LED 53 80+ AF1FEIG-1-L03-NWT
L1 L2 lamps Luminaire Efficacy
lm/w
CRI Code
silver
1760 1470 44w LED 50 80+ AS1OERG-3-L03-WW
1760 1470 44w LED 57 80+ AS1OERG-3-L03-NW
1500 550 44w LED 50 80+ AP1OERG-3-L03-WW
1500 550 44w LED 57 80+ AP1OERG-3-L03-NW
70
L2
38 L1
38
50
L2
38
38
L1
DL
DLDL
1-Längig I 1-Length:
L1
1200/1500
2-Längig I 2-Length:
.
min 20mmmax 60mm
3939
320
50
38
308
460
155
L
L
Salzburg-R1|R2 LED Mito-S1|R1 LED
19
Salzburg-R1|R2 600x600mm Recessed high output LED luminaire Suitable for mounting in ceiling tiles or plasterboard 10-30mm
Luminaire body made of Powder coated Steel, RAL9016 Involute reflectors from high efficiency ‘White Optics’ Material Opal PMMA diffuser Optic (R1) High output Louvre optic system with interchangeable glass accessory (R2) Thermal control via extruded Aluminium Heat Sink, thermal alloy 6063 0-10v Dimming option Integral 24vDC Power Supply
Mito-S1|R1 Surface & Recessed mounted LED luminaire Suitable for wall or ceiling mounting
Suitable for metal or plasterboard ceilings (max 18mm) Luminaire body made of white coated or anodised aluminium Diffuser from 4mm Opal Acryl-Satiné Remote 24vDC power supply required On-board Active thermal feed back to reduce the drive current in the event of overheating 0-10v Dimming Input
L H Lamps Luminaire Efficacy
lm/w
CRI Code
Salzburg-R1 white
595 595 30w LED 47 80+ SAOWIG-3-L03-WW
595 595 30w LED 50 80+ SAOWIG-3-L03-NW
Salzburg-R2 white
595 595 39w LED 59 83+ SALWIG-3-L43-WW
595 595 39w LED 65 83+ SALWIG-3-L43-NW
595 595 62w LED 69 83+ SALWIIG-3-L33-WW
595 595 62w LED 75 83+ SALWIG-3-L33-WW
Lamps Luminaire Efficacy
lm/w
CRI Code
Mito-S1 white
21w LED 68 80+ MIRERG-1-R22-WW
21w LED 75 80+ MIRERG-1-R22-NW
Mito-R1 white
21w LED 68 80+ MISERG-1-R22-WW
21w LED 75 80+ MISERG-1-R22-NW
Salzburg-R1|R2 LED Mito-S1|R1 LED
19
Salzburg-R1|R2 600x600mm Recessed high output LED luminaire Suitable for mounting in ceiling tiles or plasterboard 10-30mm
Luminaire body made of Powder coated Steel, RAL9016 Involute reflectors from high efficiency ‘White Optics’ Material Opal PMMA diffuser Optic (R1) High output Louvre optic system with interchangeable glass accessory (R2) Thermal control via extruded Aluminium Heat Sink, thermal alloy 6063 0-10v Dimming option Integral 24vDC Power Supply
Mito-S1|R1 Surface & Recessed mounted LED luminaire Suitable for wall or ceiling mounting
Suitable for metal or plasterboard ceilings (max 18mm) Luminaire body made of white coated or anodised aluminium Diffuser from 4mm Opal Acryl-Satiné Remote 24vDC power supply required On-board Active thermal feed back to reduce the drive current in the event of overheating 0-10v Dimming Input
L H Lamps Luminaire Efficacy
lm/w
CRI Code
Salzburg-R1 white
595 595 30w LED 47 80+ SAOWIG-3-L03-WW
595 595 30w LED 50 80+ SAOWIG-3-L03-NW
Salzburg-R2 white
595 595 39w LED 59 83+ SALWIG-3-L43-WW
595 595 39w LED 65 83+ SALWIG-3-L43-NW
595 595 62w LED 69 83+ SALWIIG-3-L33-WW
595 595 62w LED 75 83+ SALWIG-3-L33-WW
Lamps Luminaire Efficacy
lm/w
CRI Code
Mito-S1 white
21w LED 68 80+ MIRERG-1-R22-WW
21w LED 75 80+ MIRERG-1-R22-NW
Mito-R1 white
21w LED 68 80+ MISERG-1-R22-WW
21w LED 75 80+ MISERG-1-R22-NW
Eulum Design LTD
10 Takeley Business Centre
Dunmow Road
Takeley
Essex
CM22 6SJ
UK
+44 (0) 1279 870027
Eulum Design LLC
1456 Ferry Road
Suite 502
Doylestown
PA 18901
US
+1 215 290 8830
Eulum Design s.r.o.
Veleslavinova 8
746 01 Opava
CZ
+420 608 869 237
All products in the catalogue
are sold subject to Eulum
Design Terms and Conditions.
Due to our policy of continual
product improvement we
reserve the right to amend the
specification of these products
at any time.
