2014 Microchip Technology Inc. DS50002298B
EVB-USB2240-INDUser’s Manual, Rev C
DS50002298B-page 2 2014 Microchip Technology Inc.
Information contained in this publication regarding deviceapplications and the like is provided only for your convenienceand may be superseded by updates. It is your responsibility toensure that your application meets with your specifications.MICROCHIP MAKES NO REPRESENTATIONS ORWARRANTIES OF ANY KIND WHETHER EXPRESS ORIMPLIED, WRITTEN OR ORAL, STATUTORY OROTHERWISE, RELATED TO THE INFORMATION,INCLUDING BUT NOT LIMITED TO ITS CONDITION,QUALITY, PERFORMANCE, MERCHANTABILITY ORFITNESS FOR PURPOSE. Microchip disclaims all liabilityarising from this information and its use. Use of Microchipdevices in life support and/or safety applications is entirely atthe buyer’s risk, and the buyer agrees to defend, indemnify andhold harmless Microchip from any and all damages, claims,suits, or expenses resulting from such use. No licenses areconveyed, implicitly or otherwise, under any Microchipintellectual property rights.
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of ourproducts. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such actsallow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.
QUALITYMANAGEMENTSYSTEMCERTIFIEDBYDNV
== ISO/TS16949==
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are registered trademarks of Microchip Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet, KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.
GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their respective companies.
© 2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.
ISBN: 978-1-63276-459-1
EVB-USB2240-IND Evaluation Board User’s Guide
Object of Declaration: EVB-USB2240-IND
2014 Microchip Technology Inc. DS50002298B-page 3
EVB-USB2240-IND Evaluation Board User’s Guide
NOTES:
2014 Microchip Technology Inc. DS50002298B-page 4
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 7Introduction............................................................................................................ 7
Document Layout .................................................................................................. 7
Conventions Used in this Guide ............................................................................ 8
The Microchip Web Site ........................................................................................ 9
Development Systems Customer Change Notification Service ............................ 9
Customer Support ................................................................................................. 9
Document Revision History ................................................................................. 10
Chapter 1. Overview1.1 Introduction ................................................................................................... 111.2 Features ....................................................................................................... 111.3 General Description ...................................................................................... 11
Chapter 2. Getting Started2.1 Hardware ...................................................................................................... 15
2.1.1 Configuration ................................................................................. 152.1.2 Powered State LED ....................................................................... 152.1.3 Activity LED ................................................................................... 152.1.4 Media Interface .............................................................................. 152.1.5 Connector Description ................................................................... 162.1.6 Power source - Self/Bus Powered ................................................. 162.1.7 Configuration source - USB Upstream .......................................... 162.1.8 Layout Considerations ................................................................... 16
Chapter 3. Appendix A. EVB-USB2240-IND Evaluation BoardA.1 Introduction .................................................................................................. 19
Appendix B. EVB-USB2240-IND Evaluation Board SchematicsB.1 Introduction .................................................................................................. 21
Appendix C. Bill of Materials (BOM)C.1 Introduction .................................................................................................. 23
Worldwide Sales and Service .................................................................................... 27
2014 Microchip Technology Inc. DS50002298B-page 5
EVB-USB2240-IND Evaluation Board User’s Guide
NOTES:
DS50002298B-page 6 2014 Microchip Technology Inc.
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Preface
INTRODUCTION
This chapter contains general information that will be useful to know before using the EVB-USB2240-IND. Items discussed in this chapter include:
• Document Layout
• Conventions Used in this Guide
• The Microchip Web Site
• Development Systems Customer Change Notification Service
• Customer Support
• Document Revision History
DOCUMENT LAYOUT
This document describes how to use the EVB-USB2240-IND Evaluation Board as a development tool for the USB2240 Ultra Fast USB 2.0 Flash Media Controller. The manual layout is as follows:
• Chapter 1. “Overview” – Shows a brief description of the EVB-USB2240-IND Evaluation Board.
• Chapter 2. “Getting Started” – Includes instructions on how to get started with the EVB-USB2240-IND Evaluation Board.
• Appendix A. “EVB-USB2240-IND Evaluation Board” – This appendix shows the EVB-USB2240-IND Evaluation Board.
• Appendix B. “EVB-USB2240-IND Evaluation Board Schematics” – This appendix shows the EVB-USB2240-IND Evaluation Board schematics.
• Appendix C. “Bill of Materials (BOM)” – This appendix includes the EVB-USB2240-IND Evaluation Board Bill of Materials (BOM).
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is “DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the document.
For the most up-to-date information on development tools, see the MPLAB® IDE online help. Select the Help menu, and then Topics to open a list of available online help files.
2014 Microchip Technology Inc. DS50002298B-page 7
EVB-USB2240-IND Evaluation Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENTATION CONVENTIONS
Description Represents Examples
Arial font:
Italic characters Referenced books MPLAB® IDE User’s Guide
Emphasized text ...is the only compiler...
Initial caps A window the Output window
A dialog the Settings dialog
A menu selection select Enable Programmer
Quotes A field name in a window or dialog
“Save project before build”
Underlined, italic text with right angle bracket
A menu path File>Save
Bold characters A dialog button Click OK
A tab Click the Power tab
N‘Rnnnn A number in verilog format, where N is the total number of digits, R is the radix and n is a digit.
4‘b0010, 2‘hF1
Text in angle brackets < > A key on the keyboard Press <Enter>, <F1>
Courier New font:
Plain Courier New Sample source code #define START
Filenames autoexec.bat
File paths c:\mcc18\h
Keywords _asm, _endasm, static
Command-line options -Opa+, -Opa-
Bit values 0, 1
Constants 0xFF, ‘A’
Italic Courier New A variable argument file.o, where file can be any valid filename
Square brackets [ ] Optional arguments mcc18 [options] file [options]
Curly brackets and pipe character: { | }
Choice of mutually exclusive arguments; an OR selection
errorlevel {0|1}
Ellipses... Replaces repeated text var_name [, var_name...]
Represents code supplied by user
void main (void){ ...}
DS50002298B-page 8 2014 Microchip Technology Inc.
Preface
THE MICROCHIP WEB SITE
Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information:
• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
DEVELOPMENT SYSTEMS CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions.
The Development Systems product group categories are:• Compilers – The latest information on Microchip C compilers, assemblers, linkers
and other language tools. These include all MPLAB C compilers; all MPLAB assemblers (including MPASM assembler); all MPLAB linkers (including MPLINK object linker); and all MPLAB librarians (including MPLIB object librarian).
• Emulators – The latest information on Microchip in-circuit emulators.This includes the MPLAB REAL ICE and MPLAB ICE 2000 in-circuit emulators.
• In-Circuit Debuggers – The latest information on the Microchip in-circuit debuggers. This includes MPLAB ICD 3 in-circuit debuggers and PICkit 3 debug express.
• MPLAB IDE – The latest information on Microchip MPLAB IDE, the Windows Integrated Development Environment for development systems tools. This list is focused on the MPLAB IDE, MPLAB IDE Project Manager, MPLAB Editor and MPLAB SIM simulator, as well as general editing and debugging features.
• Programmers – The latest information on Microchip programmers. These include production programmers such as MPLAB REAL ICE in-circuit emulator, MPLAB ICD 3 in-circuit debugger and MPLAB PM3 device programmers. Also included are nonproduction development programmers such as PICSTART Plus and PIC-kit 2 and 3.
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
2014 Microchip Technology Inc. DS50002298B-page 9
EVB-USB2240-IND Evaluation Board User’s Guide
Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.
Technical support is available through the web site at: http://www.microchip.com/support
DOCUMENT REVISION HISTORY
Revision A (July 2014)
• Initial Release of this Document.
Revision B (September 2014)
• Update to Section 1.2 “Features”
DS50002298B-page 10 2014 Microchip Technology Inc.
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Chapter 1. Overview
1.1 INTRODUCTION
The EVB-USB2240-IND is an Ultra Fast USB 2.0 Multi-Slot Flash Media Controller with Secure Digital (SD), MultiMediaCardTM (MMC), Memory Stick® (MS), and xD-Picture CardTM (xD) connectors. The EVB-USB2240-IND demonstrates a standalone applica-tion for developers of the following applications: Flash Media Card Reader/Writer, print-ers, desktop and mobile PCs, consumer A/V, and flat panel displays, among others.
1.2 FEATURES
The EVB-USB2240-IND provides the following features:
• 36-Pin QFN (RoHS compliant) package.
• Supports these Media Types on Media I/F:
- Secure Digital (SD2.0, HS-SD, HC-SD)
- MultiMediaCardTM 4.2
- xD-Picture CardTM (population deprecated on modern assemblies)
- Memory Stick® 1.43
- High Speed Memory StickTM
- Memory Stick Pro-HGTM
- Memory Stick Duo Memory Stick ProTM
• Internal FET power switch for all media types; no external power FETs needed.
• Optionally supports external configuration.
- External I2C EEPROM for configuration options (optional).
• Low cost 4-Layer space saving design.
• Self-powered or bus-powered operation.
• Operates from a single voltage (+5.0 VDC, regulated) external power supply or from VBUS.
• Single onboard +3.3 VDC regulator.
• Optional +3.3 VDC media power LED indicator.
• Activity LED indicator.
• Single crystal clock source.
1.3 GENERAL DESCRIPTION
The EVB-USB2240-IND is an evaluation and demonstration platform featuring the USB2240 Ultra Fast USB 2.0 Flash Media Controller on a 4-layer RoHS compliant printed circuit board.
The EVB-USB2240-IND is designed to demonstrate the unique features of this device using a low-cost PCB implementation. It is designed to support internal default config-uration settings and an external I2C EEPROM (optional) for customized configured functionality. When an I2C EEPROM device is populated on the evaluation board it pro-vides customizing via USB by using the Microchip-provided USBDM utility, as required.
2014 Microchip Technology Inc. DS50002298B-page 11
EVB-USB2240-IND Evaluation Board User’s Guide
The EVB-USB2240-IND is compatible with the following:
• Microsoft® Vista
• Windows® XP
• Windows® ME
• Windows® 2k SP4
• Apple® OS X
• Linux® Mass Storage Class Drivers.
Schematics, Layout, and Bill of Materials are included minimizing new product devel-opment time.
FIGURE 1-1: TOP LEVEL SILK SCREEN AND COPPER LAYER
DS50002298B-page 12 2014 Microchip Technology Inc.
FIGURE 1-2: BOTTOM LEVEL SOLDIER SIDE AND COPPER LAYER
2014 Microchip Technology Inc. DS50002298B-page 13
EVB-USB2240-IND Evaluation Board User’s Guide
NOTES:
DS50002298B-page 14 2014 Microchip Technology Inc.
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Chapter 2. Getting Started
2.1 HARDWARE CONFIGURATION
The EVB-USB2240-IND has one onboard regulator, which generates +3.3 VDC from an external +5 VDC regulated power supply. The USB2240 generates its own +1.8 VDC for internal use using on-chip +1.8 VDC regulators. The internal 1.8 Volt regulator to the oscillator and PLL is turned off during suspend to minimize suspend current. The USB2240 consumes power from the 3.3 Volt supply.
2.1.1 Configuration
Default: The EVB-USB2240-IND has been set up to support internal default configu-ration as determined by the empty state (no valid signature ID) of the EEPROM imme-diately after reset. When no valid EEPROM image is detected, the Vendor ID, Product ID, Language ID, and Device ID, and a few other choices are set using ROM code defaults.
EEPROM Option: The EVB-USB2240-IND can load configuration from an external two-wire, I2C EEPROM U2. The EEPROM must be installed in socket U2. The EEPROM may be pre-programmed before installation, or it can be programmed with the USB host using the provided Microchip USBDM application.
This option allows access to all of the configuration registers and ID strings for the USB2240 device for detailed functional analysis and exercise as desired. The EVB-USB2240-IND is compatible with I2C EEPROMs from several manufacturers. The memory capacity must be at least 512 bytes.
2.1.2 Powered State LED
An optional LED, LED1, indicates when +3.3 VDC power is present on the media sock-ets.
2.1.3 Activity LED
LED3 indicates when the USB2240 is active, as defined by firmware.
2.1.4 Media Interface
The USB2240 supports a wide array of devices. Media Interface accommodates all of the media types supported through the use of three media socket connectors. Adapters may be needed for some form factors.
• J1 supports SD media up to the specification limit of 4 bits wide. It also supports MMC media up to the specification 4.2 of 8 bits wide.
• J2 supports xD-Picture Card media.
• J3 supports MS, MS Pro, MS Duo, and MS Pro-HG media at up to the specifica-tion limit of 8 bits wide.
Since these connectors are all on the same media bus, only one device is allowed to be inserted into any of these media socket connectors at one time for the Media Inter-face.
2014 Microchip Technology Inc. DS50002298B-page 15
EVB-USB2240-IND Evaluation Board User’s Guide
2.1.5 Connector Description
The EVB-USB2240-IND has a standard USB style connector of type B for the upstream port. It also has a standard set of media storage style connectors, which supports pop-ular flash media formats from the xD, MS, SD, and MMC families. Power is supplied via a 2.0 mm power jack. Table 2.1 lists all of the connectors. For more details on the pinout of the connectors please schematics in Figure B-1.
2.1.6 Power source - Self/Bus Powered
The EVB-USB2240-IND supports both self and bus powered operation. By default the EVB-USB2240-IND is populated for bus powered operation. Refer to the table Table 2.2 below for resistor population options to change the power source.
2.1.7 Configuration source - USB Upstream
The Microchip configuration tool named USBDM, see USB2240 Software Release Notes for details (https://www2.smsc.com/mkt/CW_SFT_PUB.nsf/Agree-ments/OBJ+Card+Reader), can configure the EEPROM when it is populated. USBDM can modify Vendor ID, Product ID, Language ID, Device ID, and configuration settings, see Figure 2.1.
2.1.8 Layout Considerations
The EVB-USB2240-IND is designed on four PCB layers: two signal layers and two sup-ply layers. The PCB layer stack is shown in Table 2.3. All signals are routed on top and bottom layers. The internal layers are ground and power. Note that the media I/F sig-nals flow easily to their destination connectors simplifying routing of critical signals.
TABLE 2-1: CONNECTOR DESCRIPTION
CONNECTOR TYPE DESCRIPTION
J1 SD/MMC4.0 SD/MMC I/F
J2 xD xD I/F
J3 MS/MS Duo/MS Pro-HG MS I/F
J5 Header GPIO Test - DNP
J6 Power Jack 2.0 mm +5 VDC Power Supply - DNP
J7 USB 2.0 Style B Upstream Port
J1 SD/MMC4.0 SD/MMC I/F
TABLE 2-2: POPULATION OPTIONS FOR SELF OR BUS POWERED OPERATION
POWER SOURCE R14 R16
Bus Powered (Default) Populate DNP
Self Powered DNP Populate
Note: DNP = Do not populate.
DS50002298B-page 16 2014 Microchip Technology Inc.
The component side top layer is shown in Figure 1-1 with silk screen information to identify component locations. Solder side and bottom layer is shown in Figure 1-2.
TABLE 2-3: PCB LAYER STACKLayer 1
Component Side1.3 - 2.3 oz. Cu finished wt.
40 mil (+/- 6 mil)
4.0 - 4.5 mil FR-4
Layer 2Ground Plane
1 oz. nominal Cu wt.
Core ~25 mil FR-4
Layer 3Power Plane
1 oz. nominal Cu wt.
4.0 - 4.5 mil FR-4
Layer 4Solder Side
1.3 - 2.3 oz Cu finished wt.
2014 Microchip Technology Inc. DS50002298B-page 17
EVB-USB2240-IND Evaluation Board User’s Guide
NOTES:
DS50002298B-page 18 2014 Microchip Technology Inc.
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Appendix A. EVB-USB2240-IND Evaluation Board
A.1 INTRODUCTION
This appendix shows the EVB-USB2240-IND Evaluation Board.
FIGURE A-1: EVB-USB2240-IND EVALUATION BOARD
2014 Microchip Technology Inc. DS50002298B-page 19
NOTES:
DS50002298B-page 20 2014 Microchip Technology Inc.
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Appendix B. EVB-USB2240-IND Evaluation Board Schematics
B.1 INTRODUCTION
This appendix shows the EVB-USB2240-IND Evaluation Board Schematics.
2014 Microchip Technology Inc. DS50002298B-page 21
EV
B-U
SB
2240-IND
Evalu
ation
Bo
ard U
ser’s Gu
ide
DS
50002298B
-page 22
2014 M
icrochip Technolo
gy Inc.
(SM_D0)(SM_D1)(SM_D2)(SM_D3)(SM_D4)(SM_D5)(SM_D6)(SM_D7)
(SM_ALE)(SM_CLE)
(SM_nWP)
(SD_WP)
(MS_D2)
(MS_D5)
(MS_D3)
(MS_D7)(MS_D6)
(MS_D4)
(MS_SCLK)
(MS_D1)
(MS_BS)
(MS_D0)
(SD_WP)
(SD_CLK)
(SD_DAT0)(SD_DAT1)(SD_DAT2)(SD_DAT3)
(SD_DAT4)(SD_DAT5)(SD_DAT6)(SD_DAT7)
(SD_CMD)
(SM_nCD)
Optional EMI Via Bypass Capacitors -- DNP
Optional EMI Field Capacitors -- DNP
Populate ONLY for special high-current media devices.
"Card Power"
OptionalOptional
GPIO6<SD_WP>/MS_CLK/SM_D4
MS_INS
_nWE_nRE
_nCE
SD_nCD
XD_CRDPWR
SM_nBR
GPIO14
CRD_PWR2
CRD_PWR2
CRD_PWR2
3V3
3V3
C70.1uFC70.1uF
XDJ2
XDJ2
VCC18
D010
D111
D212
D313
D414
D515
D616
D717
ALE6
CLE5
RE3
WE7
WP8
CE4
CD0early19
CD120
GND/CDlate1
B/R2
GND9
SHLD222SHLD121
nc123
nc224
R72.2KR72.2K
C33
0.1uF
C33
0.1uF
C1
0.1uF
C1
0.1uF
C35
0.1uF
C35
0.1uF
LED1
Bright_GRN
LED1
Bright_GRN
+ C947uFDNP
+ C947uFDNP
C23
0.001uF
C23
0.001uF
C84.7uFC84.7uF
R4 1KR4 1K
C30
0.1uF
C30
0.1uF
TP17p5x6mmTP17p5x6mm
C29
0.1uF
C29
0.1uF
C37
0.1uF
C37
0.1uF
C24
0.001uF
C24
0.001uF
tp1DNPtp1DNP
C32
0.1uF
C32
0.1uF
SD/MMC4.0Normal Mount
(Proconn)
J1
SD/MMC4.0Normal Mount
(Proconn)
J1
VCC4
D07
D18
D29
D31
CLK5
CMD2
GND13
GND26
SD_WP15DET14
SwGND318
SwGND419
D410
D612
D713
D511
SwGND116
SwGND217
nc120
nc221
Classic, Duo, ProHGMS Normal Mount
J3
Classic, Duo, ProHGMS Normal Mount
J3
VCC9D0/SDIO
4
D13
D25
D37
SCLK8
BS2
INS6
GND1
GND10
D412
D511
D613
D714
SHLD216SHLD115
nc117
nc218
C34
0.1uF
C34
0.1uF
C39
0.001uF
C39
0.001uF
C41
0.001uF
C41
0.001uF
C40
0.001uF
C40
0.001uF
C31
0.1uF
C31
0.1uF
C38
0.1uF
C38
0.1uF
C22
0.001uF
C22
0.001uF
FIGURE B-1: EVB-USB2240-IND EVALUATION BOARD SCHEMATIC 1
Do Not Populate.Development configuration ONLY
"Backlight"
"Activity"
(SCL)(SDA)
Optional EEPROM
(xD_nCD/xD_nID)
(SM_nCD)
MS-8-bit
Upstream USB ESD/EMI Treatments -- DNP
Self-Power Option -- DNP(De-pop R14 for Self-Power)
Internal Regulator Optional Capacitors -- DNP
Test Points -- DNP
Optional Signal EMI Capacitors -- DNP
Series termination onlyrequired if impedancemis-matches from driversto line cause SI or EMIissues.
VBUS
XTAL2
VDD18PLL
RBIAS
GPIO7
GPIO6<SD_WP>/MS_CLK/SM_D4
SM_nBR
SD_CMD/MS_D0/SM_CLE
SD_CLK/MS_BS/SM_nWP_R
GPIO6<SD_WP>/MS_CLK/SM_D4_R
BL_K
XTAL1
VDD18
MS_INS
SD_nCD
GPIO14
SMSM_nWESMSM_nRE
SMSM_nCE
SD_D6/MS_D7/SM_D0SD_D7/MS_D6/SM_D1SD_D0/MS_D4/SM_D2SD_D1/MS_D5/SM_D3
SD_D2/SM_D5SD_D3/MS_D3/SM_D6<Atest>SD_D4/MS_D2/SM_D7
SD_D5/MS_D1/SM_ALE
GPIO4
SD_D6/MS_D7/SM_D0_R
SD_D0/MS_D4/SM_D2_RSD_D1/MS_D5/SM_D3_R
SD_D7/MS_D6/SM_D1_R
<Atest>SD_D4/MS_D2/SM_D7_R
SD_D2/SM_D5_RSD_D3/MS_D3/SM_D6_R
SM_nRE_RSD_CMD/MS_D0/SM_CLE_RSD_D5/MS_D1/SM_ALE_R
SM_nWE_R
SM_nCE_R
SM_nBR_R
GPIO2_R
GPIO14_R
SD_nCD_R
MS_INS_R
LED1 LED1_R
USBDP
USBDM USBDM
USBDPUSBDP
USBDM
5V_EXT 5V
nRESET
VDD18PLL VDD18
LED1_R
GPIO7_R
GPIO2GPIO7
SD_CLK/MS_BS/SM_nWP
CRD_PWR2
GPIO6<SD_WP>/MS_CLK/SM_D4
SD_CMD/MS_D0/SM_CLE
SD_CLK/MS_BS/SM_nWP
5V_USB 5V
5V_USB
CRD_PWR2
GPIO2
USBDPUSBDM USBDM
USBDP
3V3
3V3
3V3
3V3
3V3
3V3
3V3
3V3
3V3
LED2ORANGE
LED2ORANGE
C10
0.1uF
C10
0.1uF
C21
10uF
C21
10uF
tp13DNPtp13DNP
RT17 33RT17 33
tp16tp16
R20 1KR20 1K
C20 0.1uFC20 0.1uF
C19
18pF
C19
18pF
J6
SelfPwr
J6
SelfPwr
1
2
3
C17
0.1uF
C17
0.1uF
C454.7pFC454.7pF
RT12 33RT12 33
tp14tp14
C46
0.1uFEMI
C46
0.1uFEMI
R1810KR1810K
RT10 33RT10 33
C28
0.1uF
C28
0.1uF
C5
0.1uF
C5
0.1uF
RT8 33RT8 33
C4
0.1uF
C4
0.1uF
RT3 33RT3 33
RT6 33RT6 33
RT2 33RT2 33
FB2 2A/0.05DCREMI
FB2 2A/0.05DCREMI
U3MIC37100-3.3WS_SOT223-3U3MIC37100-3.3WS_SOT223-3
GND
2
VIN1
3.3V_OUT3
LED3
Bright_GRN
LED3
Bright_GRN
RT15 ZeroRT15 Zero
C14
18pF
C14
18pF
R3 10KR3 10K
RT20 ZeroRT20 Zero
C26
0.001uF
C26
0.001uF
C2
0.1uF
C2
0.1uF
RT21 ZeroRT21 Zero
tp15tp15
RT22 ZeroRT22 Zero
tp12DNPtp12DNP
RT1 33RT1 33
R21 10KR21 10K
C18
1.0uFSelfPwr
C18
1.0uFSelfPwr
C25
0.001uF
C25
0.001uF
RT18 33RT18 33
BR1BGX50A
EMIBR1BGX50A
EMI
31
24
R151MegR151Meg
U2 24C04-DFN8DNP
U2 24C04-DFN8DNP
A01
A12
A23
WP7
SCL6
SDA5
VCC8
GND4
flag9
L1
DLP11SN900SL2
EMIL1
DLP11SN900SL2
EMI1 2
34
R5 33R5 33
C44 4.7pFC44 4.7pF
C11
1.0uF
C11
1.0uF
R14 ZEROBusPwr
R14 ZEROBusPwr
R13100KR13100K
tp10tp10
RT13 33RT13 33
C424.7pFC424.7pF
USB
_B-R
ECR
A-TH
RU
J7
USB
_B-R
ECR
A-TH
RU
J7
VCC1
D-2D+3
GND4
SH15
SH26
FB12A/0.05DCR
FB12A/0.05DCR
RT11 33RT11 33
C12
0.1uF
C12
0.1uF
tp8DNPtp8DNP
C434.7pFC434.7pF
R17 470R17 470
R12 33R12 33
RT9 33RT9 33
R16 ZEROSelfPwr
R16 ZEROSelfPwr
RT7 33RT7 33
R11
100K
R11
100K
Y124.000MHz
Y124.000MHz
tp11tp11
C6
0.1uF
C6
0.1uF
RT5 33RT5 33RT4 33RT4 33
C36
0.1uF
C36
0.1uF
RT14 ZeroRT14 Zero
USB
Miscellaneous
Power Card I/F
GPIO
U1 USB2240 QFN36B
USB
Miscellaneous
Power Card I/F
GPIO
U1 USB2240 QFN36B
USBDP2
USBDM3
RESET18
TEST28
XTAL232
XTAL133
VDD18PLL34
VDD18/VDDCR13
VDD336
VDD3322
VDD33/VDDCRREF14
VDDA33/VDDPLLREF36
VSS(FLAG)37
RBIAS35
<TDO>(LED1)GPIO11
(RXD)GPIO227
<TCK>(XD_ID) GPIO429
(TXD)GPIO731
(CRD_PWR2)GPIO1021
<TDI>(MS_INS) GPIO1224
<TMS>(SM_nCD) GPIO1419
<TRST>(SD_nCD) GPIO1526
SD_D6/MS_D7/SM_D08
SD_D7/MS_D6/SM_D17
SD_D0/MS_D4/SM_D25
SD_D1/MS_D5/SM_D34
GPIO6(SD_WP)/MS_CLK/SM_D430
SD_D2/SM_D525
SD_D3/MS_D3/SM_D623
<Atest>SD_D4/MS_D2/SM_D720
SD_D5/MS_D1/SM_ALE10
SD_CMD/MS_D0/SM_CLE11
SM_RE16
SM_WE12
SD_CLK/MS_BS/SM_WP9
SM_CE15
SM_B/R17
C16
1.0uF
C16
1.0uF
C13
0.1uF
C13
0.1uF
R10 12.0K1%R10 12.0K1%
J5J5
1234
C15
1.0uF
C15
1.0uF tp9DNPtp9DNP
C27
4.7uF
C27
4.7uF
R19 330R19 330 RT19 33RT19 33
C3
1.0uF
C3
1.0uF
EVB-USB2240-INDEVALUATION BOARD
USER’S GUIDE
Appendix C. Bill of Materials (BOM)
C.1 INTRODUCTION
This appendix includes the EVB-USB2240-IND Evaluation Board Bill of Materials (BOM).
2014 Microchip Technology Inc. DS50002298B-page 23
EV
B-U
SB
2240-IND
Evalu
ation
Bo
ard U
ser’s Gu
ide
DS
50002298B
-page 24
2014 M
icrochip Technolo
gy Inc.
Manufacturer Part Number Notes
GRM155R71A104KA01D
GRM1555C1H180JZ01D Critical Device
GRM188R60J106ME47D
GRM188R61C105KA93D
GRM188R60J475KE19D
BLM18EG221SN1D
SDC013-A0-5002
XDC020-A0-0000
MSCN14-X0-2200
61729-x0xxBLF
SML-412MWT86
SML-412MWT86
ERJ-3EKF1202V Critical Device
ERJ-3GEYJ104V
ERJ-3GEY0R00V
ERJ-3GEYJ105V
ERJ-3GEYJ331V
ERJ-3GEYJ103V
ERJ-3GEYJ222V
ERJ-3GEYJ222V
MCR006YZPJ330
MCR006YZPJ000
3200218
USB2240-AEZG
MIC37100-3.3WS
HCM49-24.000MABJ-UT
TABLE C-1: EVB-USB2240-IND EVALUATION BOARD BILL OF MATERIALS
Item QtyQty
PopulatedReference Designator(s) Description Manufacturer
1 9 9 C1,C4,C5,C6,C7,C12,C13,C17,C20
Capacitor, 0.1uF, 6.3V, 10%, X5R, 0402 Murata
2 2 2 C14,C19 Capacitor, 18pF, 50V, 5%, NPO, 0402 Murata
3 1 1 C21 Capacitor, 10uF, 6.3VDC, 20%, X5R, 0603 Murata
4 4 4 C3,C11,C15,C16 Capacitor, 1.0uF, 16VDC, 10%, X5R, 0603 Murata
5 2 2 C8,C27 Capacitor, 4.7uF, 6.3VDC, 20%, X5R, 0603 Murata
6 1 1 FB1 Ferrite Bead, 220 Ohm, 2A, 0.05DCR, 0603 Murata
7 1 1 J1 Connector, SD/MMC4.0, Normal Mount, SMT Proconn
8 1 1 J2 Connector Housing Assembly, XD, SMT Proconn
9 1 1 J3 Connector, Mem. Stick, Classic-Duo-Pro-HG, Top Mount, SMT
Proconn
10 1 1 J7 Receptacle, USB, Style B, Right Angle, Through-hole FCI
11 1 1 LED1 LED, Bright Green, 0603 Rohm
12 1 1 LED3 LED, Bright Green, 0603 Rohm
13 1 1 R10 Resistor, 12.0K, 1%, 1/16W, 0603 Panasonic
14 2 2 R11,R13 Resistor, 100K, 5%, 1/16W, 0603 Panasonic
15 1 1 R14 Resistor, ZERO, 0.1W, 0603 Panasonic
16 1 1 R15 Resistor, 1Meg, 5%, 1/16W, 0603 Panasonic
17 1 1 R19 Resistor, 330, 5%, 1/16W, 0603 Panasonic
18 3 3 R3,R18,R21 Resistor, 10K, 5%, 1/16W, 0603 Panasonic
19 1 1 R4 Resistor, 2.2K, 5%, 1/16W, 0603 Panasonic
20 2 2 R7,R20 Resistor, 2.2K, 5%, 1/16W, 0603 Panasonic
21 18 18 RT1,RT2,RT3,RT4,RT5,R5,RT6, RT7,RT8,RT9,RT10,RT11,RT12, R12,RT13,RT17,RT18, RT19
Resistor, 33ohm, 5%, 1/20W, 0201 Rohm
22 3 3 RT20,RT21,RT22 Resistor, Zero, 5%, 1/20W, 0201 Rohm
23 1 1 TP17 Pin, Ferrule, Uninsulated, for 0.5mm wire, 6mm long Phoenix Contact
25 1 1 U1 IC, USB2240, USB 2.0 Bus Powered Flash Media Controller, QFN-36B
SMSC
25 1 1 U3 IC, MIC37100-3.3WS, LDO Regulator, 3.3V, 1A, SOT223-3
Micrel
26 1 1 Y1 Crystal, 24.000MHz, 50ppm, 18pF, HC-49SMT Citizen America
2014
Microchip T
echnology Inc.D
S5
0002298B-p
age 25
2 GX50A Do Not Popu-late
2 RM188R61C105KA93D Do Not Popu-late
2 RM155R71A104KA01D Do Not Popu-late
3 RM155R71H102KA01D Do Not Popu-late
3 RM155R71A104KA01D Do Not Popu-late
3 RM1555C1H4R7CZ01D Do Not Popu-late
3 EV-FK1C470UR Do Not Popu-late
3 LM18EG221SN1D Do Not Popu-late
3 -146285-0 Do Not Popu-late
3 J-002AH Do Not Popu-late
3 LP11SN900SL2 Do Not Popu-late
3 50-2505 Do Not Popu-late
3 RJ-3GEY0R00V Do Not Popu-late
4 RJ-3GEYJ471V Do Not Popu-late
4 CR006YZPJ000 Do Not Popu-late
4 -146285-0 Do Not Popu-late
4 4LC04BT-I/MC Do Not Popu-late
TA
Ite Manufacturer Part Number Notes
7 1 0 BR1 Diode, Bridge, Switching, 50V, 140mA, KCAC, SOT-143
Infineon Tech B
8 1 0 C18 Capacitor, 1.0uF, 16VDC, 10%, X5R, 0603 Murata G
9 2 0 C2,C10 Capacitor, 0.1uF, 6.3V, 10%, X5R, 0402 Murata G
0 8 0 C22,C23,C24,C25,C26,C39, C40,C41
Capacitor, 1000pF, 50V, 10%, X7R, 0402 Murata G
1 12 0 C28,C29,C30,C31,C32,C33, C34,C35,C36,C37,C38,C46
Capacitor, 0.1uF, 6.3V, 10%, X5R, 0402 Murata G
2 4 0 C42,C43,C44,C45 Capacitor, 4.7pF, 50V, +/-0.25pF, NPO, 0402 Murata G
3 1 0 C9 Capacitor, 47uF, 16VDC, 20%, Aluminum, SMT, 5mm x 6mm
Panasonic E
4 1 0 FB2 Ferrite Bead, 220 Ohm, 2A, 0.05DCR, 0603 Murata B
5 1 0 J5 Header, 1 x 4, 0.1 Inch, Vertical AMP 9
6 1 0 J6 Connector, Power Jack, 2.0mm, 12V, 4A, Right Angle
Cui Stack P
7 1 0 L1 Inductor, Common Mode Choke, DLP11SN900SL2, 0504
Murata D
8 1 0 LED2 LED, Orange, 5mm, TH, Right Angle Dialight 5
9 1 0 R16 Resistor, ZERO, 0.1W, 0603 Panasonic E
0 1 0 R17 Resistor, 470, 5%, 1/16W, 0603 Panasonic E
1 2 0 RT14,RT15 Resistor, Zero, 5%, 1/20W, 0201 Rohm M
2 10 0 tp1,tp8,tp9,tp10,tp11,tp12, tp13,tp14,tp15,tp16
Header, 1 x 1, 0.1 Inch, Vertical AMP 9
3 1 0 U2 IC, 24C04, 2 Wire Serial EPROM, 4Kb, 2.5V, DFN-8 Microchip Technology 2
BLE C-1: EVB-USB2240-IND EVALUATION BOARD BILL OF MATERIALS (CONTINUED)
m QtyQty
PopulatedReference Designator(s) Description Manufacturer
EVB-USB2240-IND Evaluation Board User’s Guide
NOTES:
2014 Microchip Technology Inc. DS50002298B-page 26
DS50002298B-page 27 2014 Microchip Technology Inc.
AMERICASCorporate Office2355 West Chandler Blvd.Chandler, AZ 85224-6199Tel: 480-792-7200 Fax: 480-792-7277Technical Support: http://www.microchip.com/supportWeb Address: www.microchip.com
AtlantaDuluth, GA Tel: 678-957-9614 Fax: 678-957-1455
Austin, TXTel: 512-257-3370
BostonWestborough, MA Tel: 774-760-0087 Fax: 774-760-0088
ChicagoItasca, IL Tel: 630-285-0071 Fax: 630-285-0075
ClevelandIndependence, OH Tel: 216-447-0464 Fax: 216-447-0643
DallasAddison, TX Tel: 972-818-7423 Fax: 972-818-2924
DetroitNovi, MI Tel: 248-848-4000
Houston, TX Tel: 281-894-5983
IndianapolisNoblesville, IN Tel: 317-773-8323Fax: 317-773-5453
Los AngelesMission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608
New York, NY Tel: 631-435-6000
San Jose, CA Tel: 408-735-9110
Canada - TorontoTel: 905-673-0699 Fax: 905-673-6509
ASIA/PACIFICAsia Pacific OfficeSuites 3707-14, 37th FloorTower 6, The GatewayHarbour City, KowloonHong KongTel: 852-2943-5100Fax: 852-2401-3431
Australia - SydneyTel: 61-2-9868-6733Fax: 61-2-9868-6755
China - BeijingTel: 86-10-8569-7000 Fax: 86-10-8528-2104
China - ChengduTel: 86-28-8665-5511Fax: 86-28-8665-7889
China - ChongqingTel: 86-23-8980-9588Fax: 86-23-8980-9500
China - HangzhouTel: 86-571-8792-8115 Fax: 86-571-8792-8116
China - Hong Kong SARTel: 852-2943-5100 Fax: 852-2401-3431
China - NanjingTel: 86-25-8473-2460Fax: 86-25-8473-2470
China - QingdaoTel: 86-532-8502-7355Fax: 86-532-8502-7205
China - ShanghaiTel: 86-21-5407-5533 Fax: 86-21-5407-5066
China - ShenyangTel: 86-24-2334-2829Fax: 86-24-2334-2393
China - ShenzhenTel: 86-755-8864-2200 Fax: 86-755-8203-1760
China - WuhanTel: 86-27-5980-5300Fax: 86-27-5980-5118
China - XianTel: 86-29-8833-7252Fax: 86-29-8833-7256
China - XiamenTel: 86-592-2388138 Fax: 86-592-2388130
China - ZhuhaiTel: 86-756-3210040 Fax: 86-756-3210049
ASIA/PACIFICIndia - BangaloreTel: 91-80-3090-4444 Fax: 91-80-3090-4123
India - New DelhiTel: 91-11-4160-8631Fax: 91-11-4160-8632
India - PuneTel: 91-20-3019-1500
Japan - OsakaTel: 81-6-6152-7160 Fax: 81-6-6152-9310
Japan - TokyoTel: 81-3-6880- 3770 Fax: 81-3-6880-3771
Korea - DaeguTel: 82-53-744-4301Fax: 82-53-744-4302
Korea - SeoulTel: 82-2-554-7200Fax: 82-2-558-5932 or 82-2-558-5934
Malaysia - Kuala LumpurTel: 60-3-6201-9857Fax: 60-3-6201-9859
Malaysia - PenangTel: 60-4-227-8870Fax: 60-4-227-4068
Philippines - ManilaTel: 63-2-634-9065Fax: 63-2-634-9069
SingaporeTel: 65-6334-8870Fax: 65-6334-8850
Taiwan - Hsin ChuTel: 886-3-5778-366Fax: 886-3-5770-955
Taiwan - KaohsiungTel: 886-7-213-7830
Taiwan - TaipeiTel: 886-2-2508-8600 Fax: 886-2-2508-0102
Thailand - BangkokTel: 66-2-694-1351Fax: 66-2-694-1350
EUROPEAustria - WelsTel: 43-7242-2244-39Fax: 43-7242-2244-393Denmark - CopenhagenTel: 45-4450-2828 Fax: 45-4485-2829
France - ParisTel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Germany - DusseldorfTel: 49-2129-3766400
Germany - MunichTel: 49-89-627-144-0 Fax: 49-89-627-144-44
Germany - PforzheimTel: 49-7231-424750
Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781
Italy - VeniceTel: 39-049-7625286
Netherlands - DrunenTel: 31-416-690399 Fax: 31-416-690340
Poland - WarsawTel: 48-22-3325737
Spain - MadridTel: 34-91-708-08-90Fax: 34-91-708-08-91
Sweden - StockholmTel: 46-8-5090-4654
UK - WokinghamTel: 44-118-921-5800Fax: 44-118-921-5820
Worldwide Sales and Service
03/25/14