Evolution Quick Pop-up
A popular mid-range pop-up with self locating ‘smart’ magneticlocking arms, magnetic bars and clip-on graphic hanger fittings.
Graphic Panel Sizes
features and benefits
RE
V 1
01/
08
We are continually improving and modifying our product range and reserve the right to vary the specifications without prior notice.All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE.
1 Quad 2 Quad 3 Quad 4 Quad 5 Quad
Reg Height 776 1495 2225 2968 3710
Midi Height 647 1245 1850 2455 -
All measurements are in millimeters (mm)
Reg 673 807 673
Midi 550 675 673
NB - Widths are consistent regardless of how many quads high the pop-up is.*Straight systems allow + or - 1mm to allow for variances in floor surface.
NB - Straight systems of no more than 4 quads high are recommended.
Curved Widths Panel HeightsFront Panel Rear Panel D-End
Reg 733* 733* 673
Midi 605* 605* 673
Straight Widths Front Panel Rear Panel D-End
• Smaller ggraphic ssize ‘‘Midi’ vversion aavailable• Available iin aa ccombination oof qquad ssizes ffrom 11 xx 11 ddesktop
to 55 xx 55 ffreestanding eexhibition ddisplays• 3 qquad ggraphic hheight 22225mm aapprox• 3 qquad mmidi ggraphic hheight 11850mm aapprox• Fabric ppop-uup ppanels aare aalso aavailable• Accessories iinclude cchoice oof LLighting aand TTransit ccases
• Quality aanodised ffinish• Self-llocating ‘‘smart’ mmagnetic llocking aarms aand
low pprofile mmag bbars• Available aas fframe oonly oor ggraphic hhanging kkit • Option ffor ggraphics tto bbe ddisplayed oon bboth ssides• All ffront ccurve // DD-eend ppanels aare tthe ssame ssize• D-eend ggraphic ppanels aalso ffit tthe QQuick TTower
Kit includes: Pop-up frame, Mag Bars(for exact number refer to table onback page), D-end graphic panels and Front and/or rear graphic panels
Take the frame, ensuring that the hanging studs are at the top. Stand the frame on the floor (2)and open up (3) until the locking arms lock the frame securely into place (4)
1 2 3 4
Add the mag bars onto theframe for front, D-endsand if applicable, the rear.
5
Ensure the mag bars lockonto the magnetic hubssecurely.
6
Unwrap each graphiccarefully and attach tothe frame.
7
Carefully hook the tophanger onto the studs ofon the top node.
8
Smooth the graphic ontothe mag bars, ensuringthat it sits flat and isaligned to the centre lineof each mag bar.
9
Attach the D-End panelfront vertical edge.Curve the graphic roundto the back and attach theback vertical edge tocomplete.
10 11 12 13
Repeat steps 8 and 9 for the rest of the graphic panels.This applies to front and rear graphics if applicable.
Finally, attach theremaining D-End panel. Important note:
Remove all mag barsbefore collapsing thepop-up frame.
Assembly Instructions
Remove the backing paperfrom the graphic hanger.
Curved Graphic panel finishing
Curved Pop-up assembly
Apply the hanger to the topinside edge of the panelensuring that it is flush to thepanel edge.
Remove the backing paperfrom the kicker and apply tothe bottom edge of thepanel.
Remove the backing paperfrom the mag tape. Apply toboth sides of the panel,keeping it flush to the edge.
NB D-End panels donot require kickers.
10 11 12
Important note:Remove all mag bars beforecollapsing the pop-up frame.
Take the frame, ensuring that the hanging studs are at the top. Stand the frame on the floor (2)and open up (3) until the locking arms lock the frame securely into place (4)
1 2 3 4
Apply mag tape to straight panels accordingto the diagram (all dimensions are approx).
NB - If using graphic panels with straight hangersfollow the Curved graphic panel finishing instructions.
NB - If using graphic panels with Straight hangers follow the assembly instructions for Curved pop-ups.
Add the mag bars ontothe frame, vertically forfront and D-end panels.Then add horizontal magbars across the top andbottom of the frame.
5
For Double sided graphicsfit mag bars to the rear,running vertically andhorizontally across thepop-up frame.
6
Ensure that the magbars lock onto themagnetic pip securely.
7
Unwrap each graphiccarefully and attach tothe system.
8
Straight Graphic panel finishing
Repeat steps 8 and 9 for the rest of the graphic panels.This applies to front and rear graphics if applicable.
Straight Pop-up assembly (using horizontal mag bars)
Smooth the graphic ontothe mag bars, ensuringthat it sits flat and isaligned to the centre lineof each mag bar.
9
Attach the D-End panelfront vertical edge.Curve the graphic roundto the back and attach theback vertical edge tocomplete..
13 2
• Small 8mm tube frame withhigh tech styling
• Quality anodised aluminium finish• Tallest pop-up in the range
• Narrow footprint for use in morecompact spaces
• Enhanced graphic support• Option for graphics to be
displayed on both sides
Spider
• Quality anodised finish• All front curve / D-end panels are
the same size• Smaller graphic size ‘Midi’ version
also available• Option for graphics to be displayed
both sides
Xpress
Other products in our Pop-up range include:Single Sided21 mag bars, 4 front curved &2 D-end hangers
Double Sided30 mag bars, 4 front curved,4 rear curved & 2 D-end hangers
Single Sided18 mag bars, 3 front curved &2 D-end hangers
Double Sided24 mag bars, 3 front curved,3 rear curved & 2 D-end hangers
Single Sided15 mag bars, 2 front curved &2 D-end hangers
Double Sided18 mag bars, 2 front curved,2 rear curved & 2 D-end hangers
Single Sided12 mag bars, 1 front curved & 2D-end hangers
Double Sided12 mag bars, 1 front curved,1 rear curved & 2 D-end hangers
Single Sided21 mag bars, 4 straight hangersor 8 horizontal mag bars& 2 D-end hangers
Double Sided30 mag bars, 8 straight hangersor 16 horizontal mag bars& 2 D-end hangers
Single Sided18 mag bars, 3 straighthangers or 6 horizontal magbars & 2 D-end hangers
Double Sided24 mag bars, 6 straighthangers or 12 horizontal magbars & 2 D-end hangers
Single Sided15 mag bars, 2 straight hangersor 4 horizontal mag bars& 2 D-end hangers
Double Sided18 mag bars, 4 straight hangersor 8 horizontal mag bars& 2 D-end hangers
Single Sided12 mag bars, 1 straight hangeror 2 horizontal mag bars &2 D-end hangers
Double Sided12 mag bars, 2 straight hangersor 4 horizontal mag bars &2 D-end hangers
3 x 4 - Curved
3 x 3 - Curved
3 x 2 - Curved
3 x 1 - Curved
3 x 4 - Straight
3 x 3 - Straight
3 x 2 - Straight
(All dimensions are approx and are in mm)
3 x 1 - Straight