EXPANDED METAL PLASTERING ACCESSORIES metal.pdf · EXPANDED METAL PLASTERING ACCESSORIES 2 ISO...

1

for Building & Construction Materials

EXPANDED METAL

PLASTERING ACCESSORIES

for Building & Construction Materials

Specialized Factory for Steel ProductsSigma Factory for Steel Products

SA09/21158

8

1-4-SEL03-M11

EXPANDED METALPLASTERING ACCESSORIES

2

ISO CERTIFICATES

• For inside applications: Galvanized Steel according to BS EN 10327 superseded by BS EN 10346:2009, zinc coated on both sides.• For outside applications and humid environment: Austenitic stainless steel according to BS EN 10088- Mat.No.1.4301

Technical Specifications

Metal Beads Relevant Standards:• BS EN 13914- 2 : 2005 Design , Preparation and Application of External Rendering and Internal Plastering• BS EN 13658-1 : 2005 Metal Lath and Beads – Definitions , Requirements and Test Methods , Internal Plastering

Supersedes BS 1369-1 :1987 and BS 6452-1 : 1984• BS EN 13658 – 2 : 2005 Metal Lath and Beads – Definitions , Requirements and Test Methods , External Plastering Supersedes BS 1369-2 :1987 and BS 6452-2 : 1984 • ASTM C841 – Standard Specification for Installation of Interior Lathing and Furring• ASTM C847 – Standard Specification for Metal Lath• ASTM C1063 – Standard Specification for Installation of Lathing and Furring for Portland Cement – Based Plaster• International Building Code , ( IBC ) Chapter 25• International Residential Code , ( IRC ) Chapter 7

Galvanized Steel:• BS EN 10346:2009 (formerly BS EN 10142: 1991) coating type: Z180-275 ASTM A 653/A 653M

Stainless Steel:• BS EN 10088-2:2005 (which was directly equivalent to formerly BS 1449:Part 2:1983 in Grade 304 2B FINISH• ASTM A240/A240M in Grade 304 2B FINISH

Expanded Metal Lath & Block Work Expanded MeshRelevant Standards:• BS EN 13658-1 & 2:2005 (formerly BS 1369:Part 1:1987)• ASTM C 847

Galvanized Steel:• BS EN 10346:2009 (formerly BS EN 10142:1991) coating type:

Z180-275• ASTM A 653/A 653M

Stainless Steel:• BS EN 10088-2:2005, which was directly equivalent to formerly BS 1449:Part 2:1983 in Grade 304 2B FINISH• ASTM A240/A240M in Grade 304 2B FINISH

Reiforcement MeshRelevant Standards:• BS EN 845-3:2003 ASTM A 951/A 951M

Cold drawn steel for concrete/mansonry reinforcement• BS 4482:2005 ASTM A 496/A 496M, ASTM A 82/A 82M

Pre galvanized steel wire• BS EN 10244-2:2001 formerly BS 443 ASTM A 641/A 641M

Stainless Steel wire• BS EN 10088-3:2005 (which was direct equivalent to formerly

BS 1554:1990) BS 1449:Part 2:1983 in Grade 304 2B FINISH ASTM A 1022/A 1022M

ProductsUni-Metal expanded metal and accessories from SFSP are manufactured in compliance with international standards.

Uni-Metal provides a wide range of products capable of providing the characteristics which respond to the proposed application, along with quality of assembly, speed of installation and cost-saving expanded metal.

3

Angle Bead

Plaster Stop Bead

Movement Bead

Angle beads provide with its solid metal nose a straight corner. Expanded diamond mesh wings allow for keying the plaster right up to the nose of the bead. It is designed to protect the corners. The flanges can be easily fixed over irregular, uneven surfaces. Available in galvanized finish for internal use, and in stainless steel for external use.

Plaster stop bead provides a straight accurate line, it is used to reinforce the plaster or render on its edge. Plaster stop bead is designed as a universal plaster stop used at wall ends, door and window openings to make a neat, flush frame.

Movement Beads are used to relieve the stress and strain in large plaster areas of wall and ceiling stucco areas and to allow for movement between adjoining surface finishes. Movement Beads overcome movement tolerance in plaster and render finishes and minimize the cracking in plaster.

Reference Plaster Depth

(mm)

Material Length (mm) Qty / Box

PST 10 - GS 10 Galvanized 2700, 2850, 2900, 3000 50 Pieces




PST 10 - SS 10 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces





(mm)


MBE 10 - GS 10 Galvanized 2700, 2850, 3000 50




MBE 10 - SS 10 Stainless Steel 2700, 2850, 3000 50




ReferenceLength of

wings (mm)

Plaster Depth (mm)

Material Length (mm)Qty /

Wooden Pallets

ABE 45 - GS 45 10-13 Galvanized 2700, 2850, 3000 100 Pieces



ABE 64 - GS 64 19 Galvanized 2700, 2850, 3000 75 Pieces



ABE 45 - SS 45 10-13 Stainless Steel 2700, 2850, 3000 100 Pieces



ABE 64 - SS 64 19 Stainless Steel 2700, 2850, 3000 75 Pieces




4

Control Joint Bead

Aluminum Channel

Architrave Bead

Designed to minimize the plaster cracking and to allow movement in the plaster. Control Joint Bead overcomes movement tolerances in plaster Expansion / Control joints provide excellent expansion control for both walls and ceiling and offers positive locking of the stucco to the edge of the joint.

The Aluminum Channel is a versatile product, commonly used for groove making; a decorative purpose for plaster finishes.

Mainly used for decorative purposes to give a channel gap or a shadow between different walls finishes.


(mm)


CJB 10 - GS 10 Galvanized 2700, 2850, 3000 50 Pieces




CJB 10 - GS 10 Stainless Steel 2700, 2850, 3000 50 Pieces




Reference Size (mm) Material Length (mm) Thickness (mm)

CAL - 10 10x10x10 Aluminum 6000 1.5

CAL - 17 11x17x11 Aluminum 6000 1.5

CAL - 20 10x20x10 Aluminum 6000 1.5

CAL - 23 12.5x23x12.5 Aluminum 6000 1.5

Reference Plaster Depth (mm) Material Length (mm) Qty / Box

ACB 10 - WFG With flange 10 Galvanized 2700, 2850, 3000 50




ACB 10 - WOG Without flange 10 Galvanized 2700, 2850, 2900, 3000 50




ACB 10 - WFS With flange 10 Stainless Steel 2700, 2850, 3000 50




ACB 10 - WOS Without flange 10 Stainless Steel 2700, 2850, 2900, 3000 50




With flange Without flange

5


(mm)


MPS 03 - GS 3 Galvanized 2700, 2850, 2900, 3000 50 Pieces

MPS 06 - GS 6 Galvanized 2700, 2850, 2900, 3000 50 Pieces

MPS 03 - SS 3 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces

MPS 06 - SS 6 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces


(mm)


SMH 10 - GS 100 Galvanized 2440/3000 50 Pieces





SMH 10 - SS 100 Stainless Steel 2440/3000 50 Pieces





Micro Angle Bead

Micro Plaster Stop Beads

Strip Mesh

Micro angle beads are designed for thin coat plaster and are used at corners for protection. Micro angle beads are popular thin coat beads with fine mesh wings.Fix either by galvanized nails or using plaster dabs.

Micro plaster stops are designed for thin coat edge protection at openings. They provide abutment of plastered areas of other wall finishes. Micro plaster stops provide efficient keying and excellent finishes.

Micro plaster stops make neat, flush frames for windows and other openings.

Strip Mesh Lathes are used along stress lines where cracking is likely. Strip mesh provides reinforcement to the plaster to prevent crack over joints of different materials.

Reference Wing

Width

(mm)

Plaster

Depth(mm)


MAB 04 - GS 25x25 4 Galvanized 3000 50 Pieces

MAB 06 - GS 30x30 6 Galvanized 3000 50 Pieces

MAB 04 - SS 25x25 4 Stainless Steel 3000 50 Pieces

MAB 06 - SS 30x30 6 Stainless Steel 3000 50 Pieces


6

Coil Lath

Corner Mesh

BR. Mesh

An easy to fix lath, provides a secure key for plaster and render applications as well as offering effective joint and crack reinforcement.

Corner mesh lathes are used to prevent cracking in the plaster.

Block reinforcement meshes are produced for brick and block work reinforcement. Their primary usage is to prevent cracking. Embedded in the normal thickness of a brickwork joint, brick reinforcement meshes reduce the detrimental effects of vibration and changes of temperature. Brick reinforcement meshes increase resistance to tensional stress.

Reference Coil Lath Width (mm) Material Length (m)

CLH 10 - GS 100 Galvanized 50/100





CLH 10 - SS 100 Stainless Steel 50/100





ReferenceBR Mesh

Width (mm)

Block Width

(mm)Material Length (m) Qty / Box

BRM 50 - GS 50 100 Galvanized 50/100 50 Pieces









BRM 50 - SS 50 100 Stainless Steel 50/100 50 Pieces








Reference Length of wings

(mm)


CRM 50 - GS 50 x 50 Galvanized 2440, 3000 100 Pieces

CRM 75 - GS 75 x 75 Galvanized 2440, 3000 100 Pieces

CRM 50 - SS 50 x 50 Stainless Steel 2440, 3000 100 Pieces

CRM 75 - SS 75 x 75 Stainless Steel 2440, 3000 100 Pieces

7

Metal Sheet Lath

Metal Rib Lath

Hy-Rib Lath

Sheet lath is produced as a key for plaster when applied on suspended ceiling and walls. Sheet lath is used for encasing steel column and beams, assisting in the protection from fire. Sheet lath is used to reinforce plaster between dissimilar areas and at crack-prone areas adjacent to openings.

Rib lathes are expanded metal lathes stiffened with longitudinal ribs. The furring design of the mesh provides efficient background plaster for construction of partition, suspend ceiling and refurbishment works. Rib lath is ideal for refurbishing damaged or old masonry walls, when a key for rendering is not certain due to disintegration or softening of the wall face.

Manufactured from Pre-galvanized steel to BSEN 10327.Hy Rib is available using stainless steeI to BSEN 10088-2 type 1 .4301 . The profile of Hy Rib open mesh in combination with its ribs provide an inherently stiff sheet along its length. It can be used for flat and curved surfaces.

Reference Weight (Kg/m2) Material Dimension (mm)

SHL 064 - GS 0.64 Galvanized 2440 x 600






SHL 064 - SS 0.64 Stainless Steel 2440 x 600






Reference Weight (kg/m2) Material Size (mm) Rib Height (mm)

RBL 148 - GS 1.48 Galvanized 2500 x 700 10



RBL 148 - SS 1.48 Stainless Steel 2500 x 700 10



Thickness

(mm)

Width

(mm)

Rib Height

(mm)

Rib Distance (mm) Length

0.25 445 13 89 According to Order


0.3 445 20.5 89 According to Order






www.unitech-ikk.comwww.unimetal-ikk.comwww.sfsp-ikk.com

ManamaTel : +973 17 874 897Fax: +973 17 789 [email protected]

DohaTel : +974 4451 3301/2/3Fax: +974 4451 [email protected]

Amman Tel : +962 6 556 3030Fax: +962 6 554 [email protected]

Dubai - Al Rashidiyah / UAETel : +971 4 2591 773Fax : +971 4 2591 [email protected]

BeirutTel : +961 1 858 277Fax: +961 1 858 [email protected]

Tripoli ShowroomTel : +961 6 443 909Fax: +961 6 443 [email protected]

Abu Dhabi - Musaffah / UAETel: +971 2 552 3393Fax: +971 2 552 [email protected]

Al Ain / UAETel : +971 3 761 9050Fax: +971 3 761 [email protected]

UNITED ARAB EMIRATES

LEBANON

BAHRAIN

KINGDAOM OF SAUDI ARABIA

QATAR

MuscatTel : +968 24 591 006Fax : +968 24 597 [email protected]

OMAN

Cairo - El Gomhoria St. Tel: +20 2 2787 2152Fax: +20 2 2593 [email protected]

EGYPT

Tripoli Tel: +218 21 717 0264Fax: +218 21 477 [email protected]

LIBYA

Kuwait CityTel : +965 2 4924 937Fax: +965 2 4924 [email protected]

KUWAIT

JORDAN

JeddahTel : +966 12 627 8222Fax: +966 12 627 [email protected]

Jeddah - Ghurab ShowroomTel : +966 12 667 2000Fax: +966 12 661 [email protected]

Mak kah, TaifTel : +966 12 541 1206Fax: +966 12 532 [email protected]

Riyadh - WestTel : +966 11 431 6271Fax: +966 11 431 [email protected]

Riyadh NorthTel : +966 11 415 5465Fax: +966 11 415 [email protected]

Riyadh SouthTel : +966 11 448 0112Fax: +966 11 447 [email protected]

Qassim / BuraidahTel : +966 16 382 3946Fax: +966 16 385 [email protected]

Qassim ShowroomTel : +966 16 385 2598Fax: +966 16 385 [email protected]

Hafr el BatinTel : +966 13 729 3644Fax: +966 13 729 [email protected]

HailTel : +966 16 543 3931Fax: +966 16 543 [email protected]

Skakah / QurayyatTel : +966 14 626 3904Fax: +966 14 626 [email protected]

Khamis MushaytTel : +966 17 237 5929Fax: +966 17 237 [email protected]

NajranTel : +966 17 546 3873Fax : +966 17 546 [email protected]

SharorahTel : +966 17 532 8153Fax: +966 17 532 [email protected]

TabukTel : +966 14 423 5203Fax: +966 14 423 [email protected]

Al -BahaTel : +966 17 237 5929Fax: +966 17 237 [email protected]

GizanTel : +966 17 321 6660Fax: +966 17 321 [email protected]

Al QunfudahTel : +966 17 7350 266Fax: +966 17 7350 [email protected]

Mad inahTel : +966 14 842 1095Fax: +966 14 842 [email protected]

Mad inah Showroom - UPF Tel : +966 14 834 6244Fax: +966 14 834 [email protected]

YanbuTel : +966 14 390 1499Fax: +966 14 322 [email protected]

DammamTel : +966 13 859 0097Fax: +966 13 857 [email protected]

Dammam / ShowroomTel : +966 13 834 9300Fax: +966 13 834 [email protected]

Hufuf Tel : +966 13 530 1474Fax: +966 13 530 [email protected]

JubailTel : +966 13 361 4390Fax: +966 13 362 [email protected]

Hufuf / ShowroomTel : +966 13 586 9732Fax: +966 13 530 [email protected]

DESIGN, LOGISTICS, MATERIALS, MEDIA, R&D

FACTORIES

UNITECH GERMANYGermany, StuttgartTel : +49 711 6868 7222 Fax: +49 711 6868 [email protected]

SFSP - KSASFSP / Kingdom of Saudi ArabiaSpecialized Factory for Steel Products - 3rd Industrial City / JeddahTel: +966 12 637 4482, Fax: +966 12 636 [email protected]

Specialized Factory for Steel Products - Khumra / JeddahTel : +966 12 635 6066 Fax: +966 12 635 5658 [email protected]

SFSP / UAESIGMA Factory for Steel Products - DIC (Dubai Industrial City)Tel : +971 4 429 7024 Fax: +971 4 429 [email protected]

SFSP / EGYPTSpecialized Factory for Steel Products Lot No. 235 A- 3rd industrial zone 2nd service road 6th of October City Giza Tel : +20 2 3820 6477Tel : +20 2 3820 6235 Fax: +20 2 3820 [email protected]

SFSP / LebanonSpecialized Factory for Steel Products / s.a.r.l Tanayel, BekaaTel: +961 8 514 290Fax: +961 8 514 [email protected]

Muldit-DLebanon, Multi-D Beirut Tel : +961 1 841 155Fax: +961 1 841 [email protected]

UNITECH CHINAChina, Yiwu - Zhejiang ProvinceTel : +86 579 8545 3180Fax: +86 579 8542 [email protected]

TOSLUAE, Jebel AliTel : +971 4 8181947/4304Tel : +971 4 8181 941Fax: +971 4 [email protected]

TOSLKSATel : +966 12 627 8275Fax: +966 12 627 [email protected]

Date post:	07-Feb-2018
Category:	Documents
Upload:	dinhtuyen
View:	250 times
Download:	6 times

EXPANDED METAL PLASTERING ACCESSORIES metal.pdf · EXPANDED METAL PLASTERING ACCESSORIES 2 ISO...

Documents