of 68
7/25/2019 Export Kata Log 2
1/68
DimensionalMetrology
Hexagon Metrology Nordic AB
www.hexagonmetrology.se
http://www.hexagonmetrology.se/http://www.hexagonmetrology.se/7/25/2019 Export Kata Log 2
2/68
ii
index
Index
Mikrokator Comparators .......................................................................................................................................12
Mikrokator Comparator Stands ................................................................................................................................ 3
Mikrokator Accessories ..............................................................................................................................................4
Dial Gauges ............................................................................................................................. 57
Indicator Stands ...................................................................................................................... 89
CEJ Inside Micrometers ................................................................................................................................... 1011
Multigauging fixtures - Combicheck ............................................................................................................. 1215
Multigauging fixtures - Combifix.................................................................................................................... 1621
Multigauging fixtures - UD, Universalmtapparater, CEJ Djupmtdon ................................................ 2225
Metem Electronic Measuring System ........................................................................................................... 2628
Metem Analogue Probes ................................................................................................................................. 2933
Metem Digital Probes ....................................................................................................................................... 3437
Metem Gauging Probes .................................................................................................................................... 3841
Engineering, Calibration .............................................................................................................42
Diaclean, Gauge Block Holder ................................................................................................................................43
Plain Gauges ....................................................................................................................................................... 4449
Thread Gauges ................................................................................................................................................... 5055Pin Gauges .......................................................................................................................................................... 5657
Thread Measuring Wires ..........................................................................................................................................58
Unimeter .............................................................................................................................................................. 5962
Ativa Gauge Software ....................................................................................................................................... 6364
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
3/68
mkks d ccesses
CEJ Mkk Cmps
The Mikrokator is a mechanical instrument for measuring length, which thanks to its unique design allows graduations down to 0.1 m.
The instrument is unsurpassed in terms of accuracy. The measuring operation is purely mechanical, from the measuring tip to the
pointer measuring is completely free from friction or backlash. Thanks to its rugged construction, the Mikrokator may be used even in
tough workshop environments.
We offer a large number of models, with scale divisions from 0.005 mm (.0002") to 0.0001 mm (.000002"). Precision, linearity,
repeatability and sensitivity are all features included in the CEJ Mikrokator. This is a guarantee of high accuracy, reliability and a long
life span. In spite of all these unique features, the Mikrokator is incredibly robust. CE Johansson Mikrokators are still manufactured and
assembled in the Eskilstuna factory.
CEJ M Cmps
Mikrokator5 10
STAND 8318-01003
Mikrokator509
Mikrokator500A
Mikrokator5 10
STAND 8317-20001
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
4/68
mkks d ccesses
Ms Specl Feues
F Ovrtravl
1.0 mm (.04") in type 500
0.5 mm (.02") in types 510 and 509
Standard in all types 500 and 510-9. Optional extra in
all other Mikrokators.
Z Zro-adjusting Scrw
Standard in type 500. Optional extra in types 509 and 510.
P Adjustal masuring forc, 012 N
Optional extra in types 509 and 510.
7V Adjustal masuring forc, 0.312 N
Optional in types 509-7, 509E-55 and from 510-4 to 510-9.
With a measuring scale on the shank.
C 3/8" Shank
Optional in type 500(E).
When taking measurements on delicate objects, the measuring force is
crucial in avoiding damage. The above options are specially designed with
this in mind.
Mikrokators type 500 are available with a shank of length 55 mm on
request.
In order to take full advantage of the Mikrokator capacity, a Mikrokator with special features is needed for certain measurements.
When needed, the Mikrokator is available in a number of different designs. When ordering, please quote codes given below.
teccl Specfcs CEJ Ms, Mec pes
Type Art. no. Shank mm
Measuring Rangem
Scale divisionm
Mean MeasuringForce N ca.
Variation of Measur-ing Force N ca.
500A-2 8300-02102 8 400 5 100 70
500A-3 8300-02103 8 200 2 75 40
500A-4 8300-02104 8 100 1 75 35
500A-4-15g 8300-02104-15g 8 100 1 15 7
500A-5 8300-02105 8 50 0.5 75 25
500A-7 8300-02107 8 30 0.2 75 25
509-4 8307-05004 30 200 1 250 100
509-7 8307-05007 30 40 0.2 250 55
510-3 8308-05003 30 100 2 250 45
510-4 8308-05004 30 60 1 250 35
510-5 8308-05005 30 36 0.5 250 30
510-7 8308-05007 30 20 0.2 250 30
510-9 8308-05109 30 6 0.1 250 30
teccl Specfcs CEJ Ms, ic pes
Type Art. no. Shank mm
Measuring Rangeinch
Scale divisioninch
Mean MeasuringForce N ca.
Variation of Measur-ing Force N ca.
500EA-2 8300-52002 8 .0160 .0002 100 70
500EA-3 8300-52003 8 .0080 .0001 75 40
500EA-4 8300-52004 8 .0040 .00005 75 35
500EA-5 8300-52105 8 .0020 .00002 75 25
500EA-6 8300-52106 8 .0012 .00001 75 25
509E-4 8307-55004 30 .0100 .0005 250 100
509E-55 8307-55005 30 .0020 .0002 250 55
510E-2 8308-55002 30 .0060 .0001 250 45
510E-4 8308-55004 30 .0024 .00005 250 35
510E-5 8308-55005 30 .0014 .00002 250 30
510E-6 8308-55006 30 .0008 .00001 250 30
510E-8 8308-55008 30 .0002 .000002 250 30
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
5/68
mkks d ccesses
Extremely robust stands for the inspection of measures and tolerances
within the m range. For Mikrokators type 500, 509 and 510.
Art. no. Dscription
8317-20001 Mikrokator stand, extra stable, for shank diameter 30 mm
8317-20002 Mikrokator stand, extra stable, with height adjustment,
for shank diameter 30 mm
8317-20003 Holder arm 30 mm
8317-20004 Holder arm 8 mm
8321-01014 Holder for measuring table
8321-01015 Adjustable measuring table holder, for tables 8321-01013 and 8321-01003.
M Sd, Ex Sble a. . 8317-20001
CEJ Mkk Cmp SdsMesug Sds f Ms pe 509 d 510 a. . 8318-01003
Extremely robust precision stands for the inspection of measures and
tolerances within the m range.
With measuring arm for instruments with shank diameter 30 mm.
Measuring table 8321-01013 is included. The largest possible measure
between table and contact tip is 180 mm.
Maximum measuring depth is 80 mm. Weight 11 kg.
Fast and simple fine adjustment with high sensitivity.
Ground and chrome plated column.
Cast iron foot.
Mesug Sds f Ms pe 500 a. . 8318-01004
Extremely robust precision stands for the inspection of measures and
tolerances within the m range.
With measuring arm for instruments with shank diameter 8 mm.
Measuring table 832101013 is included 8321-01013. The largest
possible measure between table and contact tip is 190 mm.
Maximum measuring depth is 80 mm. Weight 11 kg.
Fast and simple fine adjustment with high sensitivity.
Ground and chrome plated column.
Cast iron foot.
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
6/68
mkks d ccesses
CEJ Mkk accessesM accesses
M Cc tps
Spherical 5 mm
831731001 Carbide ball
831731002 Ruby ball
Flat 10 mm
831732003
Carbide
Measuring Needle,
spherical point 1.5 mm831701004
with holder 8317-01003
Flat, adjustable, 10 mm
834301004
Carbide
Lifting Lvr for Mikrokators
509 and 510
Art. no. 8318-05001
To be attached to the shank of Mikrokators
types 509 and 510 for lifting the measuring tip.
Adjustal Masuring Tal Holdr
Art. no. 8321-01015
To be used with Measuring Table 8321-01013 and
8321-01003.
Masuring Tal 35x90x30 mm
Art. no. 8321-01013
Provided with two measuring surfaces. One surface is flat and
the opposite side is grooved with 0.6 mm wide bars. Flatness
tolerance 0.002 mm. Material: Steel, hardened and stress
relieved, black oxidized finish, measuring surfaces lapped.
8318-01020
8318-05001
8321-01015
8321-01003
8321-01013
8318-01021
Plane 3 mm
831732001
Carbide8315- Length
see table above
Adaptr 30/8 mmArt. no. 6050-30001Adapter without friction or backlash. Utilized to replacean instrument with 30 mm shank with an instrumentwith 8 mm shank. Suitable for all stands with a 30 mmholder and all contact tips for 509 and 510 Mikrokators.Attention! The contact tip shown in the picture is notincluded.
Art. no. Description Diametermm
8317-31001 Spherical, carbide (standard) * 5
8317-32001 Flat, carbide 3
8317-32003 Flat, carbide 10
8317-01003 Holder for 8317-01004
8317-01004 Measuring Needle, spherical point 1,5
8343-01004 Flat, adjustable, carbide 10
*Also available with ruby ball, art. no. 8317-31002
Contact tips for Mikrokators tp 509 and 510
Art. no. Description Lengthmm
8315-32005 Type M504A-5 5
8315-32010 Type M504A-10 10
8315-32015 Type M504A-15, standard 15
8315-32020 Type M504A-20 20
8315-02015 Type M504A-15 with ruby ball 15
Contact tips with carid or ru all for Mikrokators tp 500A
Adjustal masuring support
Art. no. 8318-01021
The support is to be attached to the column of the
stand to provide a back stop, e.g. when measuring
cylindrical workpieces. Dimension of the supporting
plate: 80x16 mm. Adjustment range 050 mm behind
the centre line of the contact tip.
Masuring tal 90x90x30 mm
Art. no. 8321-01003
Provided with one measuring surface. The surface is
grooved with 0.6 mm wide bars. Flatness tolerance
0.002 mm. Material: Steel, hardened and stress relieved,
black oxidized finish, measuring surface lapped.
Masuring Tal for Thr Point Support
Art. no. 6051-30171
Suits holder 8321-01014. For stands in series 8317.
Hight Adjustmnt Adaptr
Art. no. 8318-01020
Allows quick and accurate height adjustments.
The adapter also prevents the measuring arm from turning
around the column when the height is adjusted. This is
particularly important during differential measurements.
The adapter reduces the actual measuring height of the
stand by approx. 25 mm.
Only for stands 8318-01003 and 8318-01004
Masuring Tal 35x85x30 mm
Art. no. 8321-01016As 8321-01013 Material: Carbide mesuring surface8321-01016
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
7/68
dl guges
CEJ Dl GugesDl Guge 8336-20 Clcse Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 10 mm
Measuring range per revolution 1 mm
Diameter of external ring 58 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01020
Dl Guge 8336-21 Sc-Pf, Clcse Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 10 mm
Measuring range per revolution 1 mm
Diameter of external ring 58 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01021
Dl Guge 8336-22 Sc-Pf, Smmecl Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 2 mm
Measuring range per revolution 1 mm
Diameter of external ring 58 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01022
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
8/68
dl guges
Dl Guge 8336-23 Sc-Pf, Clcse Gdu teccl Specfcs
Graduation 0.005 mm
Measuring Range 5 mm
Measuring range per revolution 0.5 mm
Diameter of external ring 58 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01023
Dl Guge 8336-24 Sc-Pf, Smmecl Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 0.9 mm
Measuring range per revolution 0.9 mm
Diameter of external ring 58 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01024
Dl Guge 8336-25 Sc-Pf, Smmecl Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 2 mm
Measuring range per revolution 1 mm
Diameter of external ring 40 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01025
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
9/68
dl guges
Dl Guge 8336-26 Smmecl Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 0.4 mm
Measuring range per revolution 0.4 mm
Diameter of external ring 40 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01026
Dl Guge 8336-125 Sc-Pf, Clcse Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 1 mm
Measuring range per revolution 1 mm
Diameter of external ring 40 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01125
Dl Guge 8336-26 Lg Mesug Spdle, Smmecl Gdu teccl Specfcs
Graduation 0.01 mm
Measuring Range 0.4 mm
Measuring range per revolution 0.4 mm
Diameter of external ring 40 mm
Diameter of shank 8h6
Accuracy according to DIN 878
Art. no. 8336-01226
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
10/68
dc sd
idc Sd M11
idc Sd
An indicating stand for indicating and transferring of measures.The foot is equipped with dovetail guides.
Spcications:
Foot size 65 x 250 mm
Measuring height 285 mm
Measuring depth 145 mm
Column 30 mm
Attachment bore 8 mm
Weight 5.5 kg
Order no. 8320-01001
Accessories:
Fine adjustment 8320-01025
A robust stand with parallel measuring arm (8465.01005).
The foot is equipped with dovetail guides for the attachment of
a measuring table, e.g. 8462.01015 in the Combicheck System.
Spcications:
Foot size 65 x 250 mm
Measuring height 225 mm
Measuring depth 100 mm
Column 30 mm
Attachment bore 8 mm
Weight 4.5 kg
Order no. 8320-01002
idc Sd UMM-2
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
11/68
dc sd
idc Sd M11D
idc Sd M118
An indicating stand with a Diabase foot. Suitable for indicating andtransferring of measures when working on a surface plate.
Spcications:
Foot size 100 x 150 mm
Measuring height 335 mm
Measuring depth 150 mm
Column 30 mm
Attachment bore 8 mm
Weight 3 kg
Order no. 8320-01004
Accessories:
Fine adjustment 8320-01025
The bottom and the Vee-guide are magnetic.
Spcications:
Magnetic force 500 N
Foot size 60 x 75 mm
Measuring height 355 mm
Measuring depth 170 mm
Column 30 mm
Attachment bore 8 mm
Weight 3 kg
Order no. 8320-01011
Accessories:
Fine adjustment 8320-01025
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
12/68
10
inside micrometers
CEJ Inside Micrometers
CEJ Inside Micrometer Sets
Inside Micrometer Set M130
Art. no. Micrometer type Range of applicationmm
8236-33010 M130 75475
8237-33010 M130 751275
9236-33010 M158 100500
8237-33011 M158 1001300
To be used for internal measurements. The measuring anvils have carbide surfaces. The scale division is 0.01 mm over the measuring range.
Measuring range of the micrometer head is 25 mm. The extension rods are equipped with insulation against heat (not applicable to 25 and 50
mm rods). The metal surfaces have matt chromium-plating.The CEJ Inside Micrometers are available in sets, where you may combine your
own measuring range, or as fixed inside micrometer. The internal micrometer sets are suppl ied in a case, with holders.
Quotations for customized internal micrometers are available on request.
Lsring
Mtknopp
Indexhylsa
Indexstreck Mttrumma
Skalstreck
LsfjderAvslutningsdel
CEJ Fixed Inside Micrometers M158
Art. no. Range of applicationmm
Accuracym
8245-33020 325350 6.0
8245-33021 350375 6.0
8245-33022 375400 6.0
8245-33023 400425 7.0
8245-33024 425450 7.0
8245-33025 450475 7.0
8245-33026 475500 7.0
8245-33027 500525 7.0
8245-33028 525550 7.0
Accessories
Art. no. Description Accuracy, m
8235-33010 Head M130 75100 mm 5
8235-30010 End piece M130
8235-30008 Measuring knob M130
6015-70120 End piece M158
6015-81120 Measuring knob M158
8235-11012 Extension 25 mm 0.75
8235-11013 Extension 50 mm 1.0
8235-11031 Extension 100 mm 1.5
8235-11032 Extension 200 mm 2.5
8235-11033 Extension 400 mm 3.5
8235-11041 Extension 1000 mm 9
8235-11049 Extension 1500 mm 11
8235-11050 Extension 2000 mm 15
8233-01025 Holder for inside micrometer
8235-01001 Locking ring
8235-01002 Locking spring, pair
Art. no. Range of applicationmm
Accuracym
8245-33011 100125 3.5
8245-33012 125150 3.5
8245-33013 150175 4.0
8245-33014 175200 4.0
8245-33015 200225 5.0
8245-33016 225250 5.0
8245-33017 250275 5.0
8245-33018 275300 5.0
8245-33019 300325 6.0
Fixed inside micrometers are also available as standard in
lengths from 550 mm up to 1500 mm, in 25 mm intervals.
Quotations for other dimensions are available on request.
Micrometer head M130
End piece
Locking ring
Locking spring
TimbleScale divisions
Graduation
Barrel
Measuring knob
Thimble
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
13/68
11
inside micrometers
CEJ Inside Micrometers - Light weightCEJ Inside Micrometer Sets - Light weight
Inside Micrometer Set M130
Art. no. Micrometer type Range of applicationmm
8236-33010C M130 75475
8237-33010C M130 751275
9236-33010C M158 100500
8237-33011C M158 1001300
Light weight version made out of carbon fibre. To be used for internal measurements. The measuring anvils have carbide surfaces. The scale
division is 0.01 mm over the measuring range. Measuring range of the micrometer head is 25 mm. The extension rods are equipped with
insulation against heat (not applicable to 25 and 50 mm rods). The metal surfaces have matt chromium-plating. The CEJ Inside Micrometers
are available in sets, where you may combine your own measuring range, or as fixed inside micrometer. The internal micrometer sets
are supplied in a case, with holders. Quotations for customized internal micrometers are available on request.
Dial Gauge unit for Inside Micrometer
Art.no. 8237-33008
Complete with Dial Gauge 8336-01025
CEJ Fixed Inside Micrometers M158 - Light weight
Art. no. Range of applicationmm
Accuracym
8245-33020C 325350 6.0
8245-33021C 350375 6.0
8245-33022C 375400 6.0
8245-33023C 400425 7.0
8245-33024C 425450 7.0
8245-33025C 450475 7.0
8245-33026C 475500 7.0
8245-33027C 500525 7.0
8245-33028C 525550 7.0
Accessories
Art. no. Description Accuracy, m
8235-33010 Head M130 75100 mm 5
8235-30010 End piece M130
8235-30008 Measuring knob M130
6015-70120 End piece M158
6015-81120 Measuring knob M158
8235-11012 Extension 25 mm 0.75
8235-11013 Extension 50 mm 1.0
8235-11031C Extension 100 mm 1.5
8235-11032C Extension 200 mm 2.5
8235-11033C Extension 400 mm 3.5
8235-11041C Extension 1000 mm 9
8235-11049C Extension 1500 mm 11
8235-11050C Extension 2000 mm 15
8233-01025 Holder for inside micrometer
8235-01001 Locking ring
8235-01002 Locking spring, pair
Art. no. Range of applicationmm
Accuracym
8245-33011 100125 3.5
8245-33012 125150 3.5
8245-33013 150175 4.0
8245-33014 175200 4.0
8245-33015C 200225 5.0
8245-33016C 225250 5.0
8245-33017C 250275 5.0
8245-33018C 275300 5.0
8245-33019C 300325 6.0
Light weight version made out of carbon fibre. Fixed inside
micrometers as standard in lengths from 550 mm up to 1500
mm, in 25 mm intervals. Quotations for other dimensions are
available on request.
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
14/68
mulgugg fxues
CmbceckCmbcec
Combicheck is a flexible system of standard elements for build-
ing inspection fi xtures. The system has been on the market since
the 1960s and is today one of the most common and widespread
fixture systems.
Combicheck can utilize the complete C E Johansson range of
length measuring indicators, e.g. Dial Gauges, Mikrokators, Metem
Digital Gauging System and Pneumatic Measuring Devices. It may
be integrated into machine tool CNC systems for full measuring
control. Combicheck is so robust that it can advantageously
be used by operators in a workshop environment.
Choice of reading-, calculation- or control devices should be
made in view of
quantities, dimensions, tolerance ranges and batch sizes
operator capability and extent of automation
co-ordination with the machining operations
All Combicheck elements are represented in the following
pages. They are divided into groups by reference to their func-
tion. More detailed size information etc. is obtained through the
CEJ Combicheck catalogue, or at www.cej.se.
8460 Base Plates CEJ Art. no.
8461 Brackets CEJ Art. no.
Mounting bracket for horizontal column 8461-01001
Mounting bracket for vertical column 8461-01002
Mounting bracket for roller slide 8461-01003
Mounting bracket, universal 8461-01004
Cmbcec Sdd accesses
Width 125, length 250 mm 8460-01001
Width 125, length 500 mm 8460-01002
Width 125, length 1000 mm 8460-01004
Width 255, length 250 mm 8460-01010
Width 255, length 500 mm 8460-01011
Width 255, length 1000 mm 8460-01013
tel 1616 08 10 fax 1616 08 90 [email protected]
http://www.cej.se/mailto:[email protected]:[email protected]://www.cej.se/7/25/2019 Export Kata Log 2
15/68
mulgugg fxues
8462 CEJ Art. no.
Vee-block support 120, measuring range 5-80 mm 8462-01001Holder 8462-01003
Holder plate 8462-01004
Vee-plate 120, measuring range 5-80 mm 8462-01005
Vee-plate 108, measuring range 5-80 mm 8462-01006
Axial stop 8462-01007
Guide 8462-01008
Vee-plate 120 for conical components, 5-80 8462-01011
Vee-plate 108 for conical components, 5-80 8462-01012
Roller Vee-support, 32-102 mm 8462-01013
Measuring table, width 80 mm, length 160 mm 8462-01015
Insert guide, length 70 mm 8462-01020
Vee-locator120, measuring range 10-70 mm 8462-01025
Vee-locator120, measuring range 70125 mm 8462-01026
Axial stop arm, length 145 mm 8462-01027
Centre support, movable centre, height 200 mm 8462-01028
Centre support, fixed centre, height 200 mm 8462-01029
Centre support, fixed centre, height 125 mm 8462-01030
Centre support, movable centre, height 125 mm 8462-01031
Point centre, 14, 60, length 90 mm 8462-01032
8463 Transport Devices CEJ Art. no.
Roller slide, width 50, length 65 mm 8463-01001
Roller slide, width 80, length 125 mm 8463-01002
Stop attachment 8463-01003
Handle, length 65 mm 8463-01004
Handle, length 120 mm 8463-01005
Cmbcec Sdd accesses
8464 Columns CEJ Art. no.
Column 30, length 200 mm 8464-01001
Column 30, length 350 mm 8464-01002
Column 30, length 600 mm 8464-01003
Dovetail attachment length 198 mm 8464-01005
Dovetail attachment length 348 mm 8464-01006
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
16/68
mulgugg fxues
8467 Length Measuring Elements, bore 8 or 3/8" CEJ Art. no.
Length Measuring Elements 8467-01001
Length measuring head 90 8467-01003
Measuring arm, length 80 mm 8467-01005
Instrument holder 8467-01007
8465 Instrument holder, bore 8 or 3/8" CEJ Art. no.
Measuring Range 0160 mm 8465-01001Measuring Range 0160 mm 8465-01002
Straight 8465-01004
Parallel measuring arm 8465-01005
Pivoted 8465-01006
Length 76 mm 8465-01008
Length 101 mm 8465-01009
Length 126 mm 8465-01010
Length 151 mm 8465-01011
Length 176 mm 8465-01012
8466 Measuring Frames, bore 8 or 3/8" CEJ Art. no.
C-C125, measuring range 0125 8466-01001
C-C175, measuring range 0125 8466-01002
C-C175, measuring range 125225 8466-01003
8468 Measuring organs (measuring anvils etc.) CEJ Art. no.
Chisel anvil, length 2 mm 8468-01001
Chisel anvil, length 6 mm 8468-01002
Chisel anvil, length 12 mm 8468-01003
Chisel anvil, length 3.5 mm 8468-01004
Chisel anvil, length 5 mm 8468-01005
Chisel anvil, length 8 mm 8468-01006
Chisel anvil, length 12 mm 8468-01007
Chisel anvil, length 16 mm 8468-01008
Chisel anvil, length 6.5 mm 8468-01009
Chisel anvil, length 10 mm 8468-01010
Support anvil 8, length 35 mm 8468-01015
Support anvil 8, length 60 mm 8468-01016Measuring tip, plane, 4, length 6 mm 8468-01025
Measuring tip, plane, 4, length 10 mm 8468-01026
Measuring tip, plane, 7.7, length 3 mm 8468-01029
Cmbcec Sdd accesses
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
17/68
mulgugg fxues
8471 Internal measuring elements CEJ Art. no.
Length meas. element, relative, bore 8 or 3/8" 8471-01001
Length meas. element, single, bore 8 or 3/8" 8471-01002
Height measuring element, bore 8 8471-01003
Base plate 8471-01005
Measuring support 8471-01006
Centre piece 8471-01007
Anvil support 8471-01008
Link 8471-01009
Shaft 8471-01010Location anvil 8471-01011
Cover plates 8471-01012
Spacer, 12, height 1 mm 8409-01110
Spacer, 12, height 2 mm 8409-01111
Spacer, 12, height 4 mm 8409-01112
Spacer, 12, height 7 mm 8409-01113
8468 Measuring organs (measuring anvils etc.) CEJ Art. no.
Measuring tip, spherical, R8, length 5 mm 8468-01030Measuring tip, plane, 1.5, length 8 mm 8468-01031
Measuring tip, tapered, length 10 mm 8468-01032
Measuring tip, plane, 1.5x1.5, L=21 mm 8468-01033
Extension, length 10 mm 8468-01035
Extension, length 30 mm 8468-01036
Extension, length 40 mm 8468-01037
Spindle for measuring tip 8468-01040
Adapter, threaded M2,6 8468-01041
Measuring tip, carbide ball, L=5 [M504A-5] 8315-32005
Measuring tip, carbide ball, L=10 [M504A-10] 8315-32010
Measuring tip, carbide ball, L=15 [M504A-15] 8315-32015
Measuring tip, carbide ball, L=20 [M504A-20] 8315-32020
8469 Other elements, bore 8 or 3/8" CEJ Art. no.
Extension shaft, length 60 8469-01001
Angle head 45, length 60 8469-01003
Angle head, 90, length 60 8469-01004
Angle head, 45, length 20 8469-01005
Angle head, 90, length 20 8469-01006
Pressure arm 8469-01007
Spring loaded plunger 8469-01008
Mounting arm 8469-01020
Link 8469-01021
Cmbcec Sdd accesses
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
18/68
mulgugg fxues
Combifix is a system of standard elements, which are used to
build multigauging fixtures. Combifix is especially useful for
quick and frequent measurements in workshop environments.
The strength of the Combix system is that it is relatively cheap to build
a xture for gauging one specic workpiece. If the workpiece is modied
or taken out of production, the investment in Combix is not wastedthe
standard elements can be used as components in the next gauging
xture.
The Combifix may be used with the complete C E Johansson range
of length measuring indicators, e.g. dial gauges, Mikrokators, Metem
Digital Gauging System and Pneumatic Gauges. It may be integrated
into machine tool CNC systems for full measuring control.
In the following pages there are examples of different Combifix
multigauging fixtures, as well as an overview of all Combifixelements. Detailed dimensional data and descriptions are
available in the CEJ Combifix catalogue and at www.cej.se.
CmbfxCmbfx
Frame Bridges CEJ art. no.
A 8472-01001
A1 8472-01002
A2 8472-01003
Fixed Measuring Arms CEJ art. no.B 8472-01004
B1 8472-01005
B2 8472-01006
B3 8472-01007
B4 8472-01008
B5 8472-01009
B6 8472-01010
B7 8472-01011
B8 8472-01012
B9 8472-01013
Mobile Measuring Arms CEJ art. no.
C 8472-01014
C1 8472-01015
C2 8472-01016
C3 8472-01017
C4 8472-01018
C5 8472-01019
C6 8472-01020
C7 8472-01021
C-S 8472-01022
C1-S 8472-01023
C2-S 8472-01024
Ps f Mesug Fmes
tel 1616 08 10 fax 1616 08 90 [email protected]
http://www.cej.se/mailto:[email protected]:[email protected]://www.cej.se/7/25/2019 Export Kata Log 2
19/68
mulgugg fxues
Gauge holder CEJ art. no.
D2 8472-01025
D3 8472-01026
D4 8472-01027
Measuring Stop CEJ art. no.
E 8472-01028
E2-25 8472-01030
E3 8472-01031
E4-60 8472-01033
E4-110 8472-01035
E4-210 8472-01037
E5 8472-01038
E6 8472-01039
Spring Bracket CEJ art. no.
F 8472-01040
F1 8472-01041
F2-11 8472-01042
F2-17 8472-01043
F2-20 8472-01044
Brackets for measuringelements
CEJ art. no.
G 8472-01046
G5 8472-01047
Measuring anvils CEJ art. no.
H-20 8472-01048
H-40 8472-01049
H-60 8472-01050
H2-20 8472-01051
H2-40 8472-01052
H2-60 8472-01053
H33-20 8472-01054
H33-40 8471-01027
H33-60 8471-01029
H35-20 8472-01057
H35-40 8471-01021
H35-60 8471-01023
Slot Measuring Anvil CEJ art. no.
J5 8472-01060
J6 8472-01061
Ps f Mesug Fmes
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
20/68
mulgugg fxues
Accessories CEJ art. no.
K Screw 8472-01062
K1-50 Shaft 8472-01063
K1-75 8472-01064
K1-100 8472-01065K1-125 8472-01066
K1-150 8472-01067
K1-175 8471-01068
K1-200 8471-01069
K1-250 8472-01070
K2 Conical Locking Nut 8472-01071
K4-19 Draw Spring 8472-01072
K4-29 8472-01073
K4-37 8472-01074
K4-45 8472-01075
K4-55 8472-01076
K5 Screw 8472-01077
K6 Locking Screw 8472-01078
K7 Clamping Sleeve 8472-01079
K7E 8472-01080
Coordinate Table CEJ art. no.
UA21 8472-01219
UA22 8472-01220
UA51 8472-01221
UA52 8472-01222
Finding Units CEJ art. no.
UB20 8472-01223
UB21 8472-01224
UB22 8472-01225
UB50 8472-01226
Measuring ElementAttachments
CEJ art. no.
UG20 8472-01230
UG50 8472-01231Gauge holder CEJ art. no.
UD01 8472-01227
UD02 8472-01228
Ps f Cde Mesugs
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
21/68
mulgugg fxues
Ball Bearing for meas-uring arms
CEJ art.no.
MA00 8472-01117MA01 8472-01118
MA02 8472-01119
MA03 8472-01120
MA04 8472-01121
MA10 8472-01122
MA11 8472-01123
MA12 8472-01124
MA13 8472-01125
MA14 8472-01126
MA20 8472-01127
MA21 8472-01128
MA22 8472-01129
rces . Bll Begs
Rocker w. Ball Bearing CEJ art.no.
PL115 8472-01152
PL120 8472-01153
PL130 8472-01154
PL140 8472-01155
PL150 8472-01156
PL160 8472-01157
PL215 8472-01158
PL220 8472-01159
PL230 8472-01160
PL240 8472-01161
PL250 8472-01162
PL260 8472-01163
PL315 8472-01164
PL320 8472-01165
PL330 8472-01166
PL340 8472-01167
PL350 8472-01168
PL360 8472-01169
PL415 8472-01170
PL420 8472-01171
PL430 8472-01172
PL440 8472-01173
PL450 8472-01174
PL460 8472-01175
PL515 8472-01176
PL520 8472-01177
PL530 8472-01178
PL540 8472-01179
PL550 8472-01180PL560 8472-01181
Rocker w. Ball Bearing CEJ art.no.
PR115 8472-01189
PR120 8472-01190
PR130 8472-01191
PR140 8472-01192
PR150 8472-01193
PR160 8472-01194
PR215 8472-01195
PR220 8472-01196
PR230 8472-01197
PR240 8472-01198
PR250 8472-01199
PR260 8472-01200
PR315 8472-01201
PR320 8472-01202
PR330 8472-01203
PR340 8472-01204
PR350 8472-01205
PR360 8472-01206
PR415 8472-01207
PR420 8472-01208
PR430 8472-01209
PR440 8472-01210
PR450 8472-01211
PR460 8472-01212
PR515 8472-01213
PR520 8472-01214
PR530 8472-01215
PR540 8472-01216
PR550 8472-01217PR560 8472-01218
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
22/68
0
mulgugg fxues
Rocker w. Ball Bearing CEJ art.no.
PM01 8472-01182
PM02 8472-01183
PM03 8472-01184
PM04 8472-01185PM10 8472-01186
Attachments CEJ art.no.
PG15 8472-01146
PG20 8472-01147
PG30 8472-01148
PG40 8472-01149
PG50 8472-01150
PG60 8472-01151
Gauge holder CEJ art.no.
PD01 8472-01130
PD02 8472-01131
Measuring anvils CEJ art.no.
PE01 8472-01132
PE02 8472-01133
PE03 8472-01134
PE04 8472-01135
PE05 8472-01136
PE20 8472-01137
PE30 8472-01138
PE40 8472-01139
PE50 8472-01140PE60 8472-01141
PE70 8472-01142
PE80 8472-01143
PE90 8472-01144
PE100 8472-01145
Roller Slide CEJ art.no.
LR300 8472-01102LR310 8472-01103
LR320 8472-01104
LR330 8472-01105
Pivoting Fixture CEJ art.no.
LS200 8472-01110
LS400 8472-01111
LS600 8472-01112
Bsc Fxues Cgg Dece
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
23/68
mulgugg fxues
Roller Table CEJ art.no.
LT100 8472-01114
LT150 8472-01115
LT250 8472-01116
Exchangeable Plates CEJ ar t.no.LP01 8472-01089
LP02 8472-01090
LP20 8472-01092
LP40 8472-01095
LP60 8472-01097
Groove Plates CEJ art.no.
LP25 8472-01093
LP45 8472-01096
Plate Holder CEJ art.no.
LG01 8472-01081
Base Plate CEJ art.no.
LV250 8460-01001
LV500 8460-01002
LV1000 8460-01004
Accessories for Base Platessee the CE JohanssonCombicheck range.
Bse Ples accesses
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
24/68
mulgugg fxues
The UD Unit is used with gauges with a
standard shank, 8 h6 or 30 h6.
Depending on the requirements to be met,
you may select one of the many different
models and types available on the market.
UD - Uesl Mesug UsUDUesl Mesug Us
The UD Measuring Units are exible measuring devices intended for inspecting
rings and ball bearings, with
the following additional versatile areas of application:
external and internal diameters
large measuring ranges
inspecting out-of-roundness: two- and three-point measurements.
height measurements
thickness of material, radially
skewness
In addition, the different measurements may be combined. Add a high level of
accuracy,
an attractive price and the fact that the device has been around on the market
for decades and you will get a product that you can relay on in many different
inspection contexts. All in one device.
teccl d
The UD Unit is available in two sizes. It is made of cast
iron and all essential parts arecorrosion protected with
a durable powder coat finish The measuring units are
combined with standard accessories for various types of
measurements.
TECHNICAL DATA UD-1 UD-2
CE JART.NO. 8409-01011 8409-01012
Measuring range, outside , mm 5 - 140 5 - 310
Measuring range, inner , mm 14 - 165 14 - 340
Top of table, mm 165 340
Length, mm 180 320
Width, mm 182 360
Hight, mm 100 125
This set of selected accessories is recommended as an
initial base, to be extended when necessary. The smallest
possible inner diameter that can be checked with these
accessories is 31 mm.
8409-01030 2 pcs Studs 8462-00041 1 pce Stud 8462-00043
3 pcs Measuring discs 8409-01060
3 pcs Spacers 8409-01110
3 pcs Spacers 8409-01111
3 pcs Spacers 8409-01112
3 pcs Spacers 8409-01113
1 pce Vee nut 8409-01130
3 pcs Nuts ML6M6 8409-01132
1 pce Adapter 8409-01050
CEJ ART.NO. PARTSINCLUDED
Bsc accesses Se
recmmeded Dl Guges
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
25/68
mulgugg fxues
Apart from the accessories included in the basic accesso-
ries set, there are a number of standard accessories, which
allow measurements of inside diameters down to 14 mm.
All measures in the left hand table are stated in mm.
Instrument holder L=76 1 8465-01008
" L=101 1 8465-01009
" L=126 1 8465-01010" L=151 1 8465-01011
" L=176 1 8465-01012
Spacing piece for indicators 8 mm 2 8409-01050
Measuring hook, inwards, carbide tip, radius 2,5 3
A=19 B=16 C=5 D=23 8409-31070
A=25,5 B=22,5 C=6 D=23 8409-31071
A=30,5 B=27,5 C=6 D=23 8409-31072
Measuring hook, outwards, carbide tip, radius 2,5 4
A=25,5 B=21,5 C=11 D=38 8409-31080
A=32 B=28 C=11 D=45 8409-31081
A=39 B=35 C=11 D=45 8409-31082
A=46 B=42 C=11 D=45 8409-31083
Measuring plane D=18 H=5 5 8409-01102
Measuring table (2-point) D=50 H=20 6 8409-01100
Measuring table (3-point) D=50 H=20 7 8409-01101
Measuring support, carbide edge, radius 1,5 8
L=40 H=20 A=12 B=32 8409-31095
Measuring arm, carbide tip, radius 2,5 9
L=50 H=12 A=42 B=25 8409-31090
Meas. disc D=15 H=2 R=1 10 8409-01060
" D=15 H=4 R=1 10 8409- 01061
" D=27 H=1 R=0,5 10 8409-01065
" as 8409-01061 but with carbide 10 8409-31061
Yoke upper H=2 11 8409- 01105
Yoke lower H=5 12 8409- 01106
Spacer 12, hjd 1 8409-01110
" 12, hjd 2 8409-01111
" 12, hjd 4 8409-01112
" 12, hjd 7 8409-01113
Flange sleeve for 8409-01011, hight 20 8409-01125
Flange sleeve for 8409-01012, hight 25 8409-01126
Stud length 15 8462-00039
" length 25 8462-00040
" length 35 8462-00041
" length 45 8462-00042
" length 55 8462-00043
" length 65 8462-00044
" length 75 8462-00045
Vee groove nut, M6, length 15 8461- 00011
Vee groove nut, M6, rounded border 8409- 01130
Screw countersunk 6x14 8409- 01131
Nut ML6M6 8409- 01132
Angle stand for 8409-01011, inclination 35 8409- 01036
Angle stand for 8409-01012, inclination 18 8409- 01037
Description Picture no. CEJ art. no.
BILD NR 1
BILD NR 2
BILD NR 3 BILD NR 4
BILD NR 5
BILD NR 6 BILD NR 7
BILD NR 8
BILD NR 9
BILD NR 10 BILD NR 12BILD NR 11
UDSdd accesses
Picture no. 1
Picture no. 2
Picture no. 3 Picture no. 4
Picture no. 5
Picture no. 6 Picture no. 7
Picture no. 8
Picture no. 9
Picture no. 1
Picture no. 10 Picture no. 11 Picture no. 12
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
26/68
dep mesug guge
CEJ Dep Mesug GugeCEJ Dep Mesug Guge
Depth Measuring Gauge
8412-01001
CEJ Depth Measuring Gauge is used for accurate measurements of
inner distance, directly in conjunction with the machining operation or
at the final inspection. As a reading device you may use a Dial Gauge, aMikrokator or an Inductive Probe, connected to an electronic measuring
instrument.
The Depth Measuring Gauge is equipped with a wide range of standard
accessories, e.g.
Exchangeable Measuring Tables 35 115 mm.
Measuring pistons, lengths up to 104 mm.
Measuring Anvils and Measuring Plates 8 55 mm for measurements
in places which are difficult to access.
The measuring force may be adjusted to 200, 500 or 750 grams by
changing the measuring force spring.
Depth Measuring Gauge Art. no. 8412-01001 comes without dial gauge,
measuring table or measuring piston.
Sdd ccesses
Picture Description CEJ Art. no.
1 Measuring table D=35 mm 8412-01005
1 Measuring table D=45 mm 8412-01006
1 Measuring table D=55 mm 8412-01007
1 Measuring table D=65 mm 8412-01008
1 Measuring table D=75 mm 8412-01009
1 Measuring table D=85 mm 8412-01010
1 Measuring table D=95 mm 8412-01011
1 Measuring table D=105 mm 8412-01012
1 Measuring table D=115 mm 8412-01013
3 Contact tip D= 8 mm 8412-01040
3 Contact tip D= 10 mm 8412-01041
3 Contact tip D= 12 mm 8412-01042
5 Meas force spring, P=2 N, L=30 mm* 8412-01065
5 Meas force spring, P=5 N, L=30 mm 8412-01066
5 Meas force spring, P=7.5 N, L=30 mm 8412-01067 6 Holder for measuring table* 8412-01070
7 Bushing* 8412-01075
Pcue . 1
Pcue . 5 Pcue . 6
Pcue . 7
Pcue . 3
* included in art. no. 8412-01001
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
27/68
dep mesug guge
Picture Measuring disc CEJ Art. no.
4 D=14 mm 8412-01043
4 D=16 mm 8412-01044
4 D=18mm 8412-01045
4 D=20 mm 8412-01046
4 D=22 mm 8412-01047
4 D=24mm 8412-01048
4 D=26 mm 8412-01049
4 D=28 mm 8412-01050
4 D=30 mm 8412-01051
4 D=32 mm 8412-01052
4 D=34 mm 8412-01053
4 D=36 mm 8412-01054
4 D=38 mm 8412-01055
4 D=40 mm 8412-01056
4 D=45 mm 8412-01057
4 D=50 mm 8412-01058
4 D=55 mm 8412-01059
Picture Measuring Piston CEJ Art. no.
2 L= 40 mm A= 0-4 mm 8412-01015
2 L= 45 mm A= 4-9 mm 8412-01016
2 L= 50 mm A= 9-14 mm 8412-01017
2 L= 55 mm A= 14-19 mm 8412-01018
2 L= 60 mm A= 19-24 mm 8412-01019
2 L= 65 mm A= 24-29 mm 8412-01020
2 L= 70 mm A= 29-34 mm 8412-01021
2 L= 75 mm A= 34-39 mm 8412-01022
2 L= 80 mm A= 39-44 mm 8412-01023
2 L= 85 mm A= 44-49 mm 8412-01024
2 L= 90 mm A= 49-54 mm 8412-01025
2 L= 95 mm A= 54-59 mm 8412-01026
2 L= 100 mm A= 59-64 mm 8412-01027
2 L= 105 mm A= 64-69 mm 8412-01028
2 L= 110 mm A= 69-74 mm 8412-01029
2 L= 115 mm A= 74-79 mm 8412-01030
2 L= 120 mm A= 79-84 mm 8412-01031
2 L= 125 mm A= 84-89 mm 8412-01032
2 L= 130 mm A= 89-94 mm 8412-01033
2 L= 135 mm A= 94-99 mm 8412-01034
2 L= 140 mm A= 99-104 mm 8412-01035
Pcue . 2 Pcue . 4
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
28/68
26
metem
CEJ Metem Electronic Measuring System
CE Johansson offers the market's most flexible measuring system for retrieval, presentation, feed-back and measurement control.
The Metem System includes a number of elements that constitute a flexible area of application in length measuring electronics.
The Metem System, in combination with fixtures or stand-alone measuring equipment, handles everything from the most simple
demands to more demanding applications with measurement control applied to unmanned production cells.
Metem 3000s Industrial Computer
Metem 3000s is an Industrial Computer for tough workshop
environments. Suitable for applications in production shops.
Art. no. 8644-01303 Metem 3000s with table stand
Art. no. 8644-01304 Metem 3000s with swivel stand
for mounting on fixture cabinets etc.
Metem 9002 Probe Interface
Metem 3005 SPC Software
Metem 3005 is a powerful, operator friendly SPC
software for the retrieval and presentation of
measurement data. Metem 3005 allows feed-back
to converting machines with process control
servers. Also includes a simple plc function for
the control of fixtures etc.
Art. no. 8990-10082 Metem 3005
Metem 3000s is a probe interface, allowing the connection
of 16 probe signals.
Art. no. 8644-01138 Metem 9002 Probe Interface
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
29/68
27
metem
Total error of calibration, linearity and stability
[with one probe]
Scales/Display M551
8646-010033 [30 divisions] and 10 [20 divisions]
M552
8646-01004LCD, 4 digits, 3 updates/sec
2% of the displayed value
Zero setting 125 m, depending on range
Probe inputs 4 (+A, -A, +B, -B)
Functions one probe, A:
one probe, B:
two probes:
+A, -A
+B, -B
+A+B, +A-B or -A+B, -A-B
Output signals 1V at maximum reading
2V at maximum range
0.5%
2 mA
1 ohm
analogue signal, M551
analogue signal, M552
accuracy of output signal in contact
load capacity
impedance out
Size width 155 mm, height 105 mm, depth 200 mm
IP rating IP50 according to IEC 529
Technical Data Metem 551 and 552
M551
8646-01003
M552
8646-01004 2% of the displayed value
Metem 552 with digital display
Art. no. 8646-01004
Metem 551 with analogue display
Art. no. 8646-01003
Batteries for Metem 551 and 552
Art. no. 8646-00024
Metem 551 and 552
Metem Display Instrument
Metem 551 and 552 are respectively, analogue and digital measuring instruments, used with indicating hand gauges like
bore and shaft gauges or with probes in a measuring stand, etc..
Metem 551 and 552 are designed for dimensional measuring and inspection. The measurements can be made with bore orshaft gauges, or with measuring stands. Metem 551 is an analogue instrument for metric and inch units. The instrument
reading is adjustable from 10 m to 1000 m (.0003" to .03"). Metem 552 displays the measuring results digitally,
in metric or inch units. The display ranges are 20 m, 200 m and 2000 m (.2000, .0200 and .0020).
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
30/68
meem
Meem 2000Meem 2000 Dspl U
Metem 2000 is a very competent display unit for digital measuring probes and gauge probes. It is possible to connect up
to 30 digital measuring probes and/or gauge probes to Metem 2000. Metem 2000 is a breakthrough in ergonomic design.
The ordinary numeric display of measurement values is extended with an auto adapted alpha numeric display. During thecharging process, this display window with 24 characters is guiding the operator through a suite of menus.
In the function mode, the auto adapted display is showing the function (dened during the set-up) of four programmable push
buttons, giving direct access to suitable control functions. You may connect Metem digital probes as well as Metem gauge probes
to Metem 2000.
Art. no.
Numerical display
Size of display
Maximum resolution
with gauge probes
with digital measuring probes M946
with digital measuring probes M947
with digital measuring probes M948
with digital measuring probes M949
Information display
Indicating lamps for tolerance limits
Program number display
8644-01200
9 digit LED indicators with polarity and decimal point.
999.999 99 mm or 39.370078 inch, with automatic
suppression of redundant leading zeroes.
0.05 m or 2 micro inch
0.05 m or 2 micro inch
0.1 m or 5 micro inch
0.5 m or 20 micro inch
0.5 m or 20 micro inch
24 characters alphanumeric display with two function modes.
Show Hi/OK/Lo for the detection of limit values
Independent one digit display.
teccl D Meem 2000
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
31/68
meem
Meem algue PbesCE Johansson analogue Metem probes have the highest quality and accuracy. The most important capability parameters are
repeatability and linearity. The Metem probes retain the same sensitivity all along the measuring stroke, and the linearity
quoted for the standard probes includes sensitivity dependent errors.
The design of the Metem probes is robust, and they are suitable for measuring labs as well as for workshops. Thanks to thestandard shank size (8h6), the probes may be used in a large number of applications; in multigauging fixtures with Metem
instruments, in measuring stands, in indicating hand gauges, such as bore gauges etc.
Other features are:
Measuring spindle with ball bearing in probes M910, M911, M913, M917 and M919 for smooth motion and freedom from play.
Membrane bearing of the measuring spindle in M916 makes the spindle movement friction-free.
Calibrated for connection to all Metem instruments.
Mechanically adjustable zero point (not in M916).
In a conventional pen probe, the measuring tip is pushed outwards by a
built-in spring. Probes with spring push are available in types M910, M911,
M913 and M919. These probes have an axial cable outlet, but the cable may
easily be angled 90 by mounting the enclosed radial outlet adapter.
The probes may be delivered with a spiral braided cable as standard. This
is very convenient when using the probe in connection with indicating hand
gauges, for example. Cable length 450 mm, when extended about 2 m.
When tting the probe in a xture, you have to construct a mechanism,
which brings the probe in contact with the workpiece to be measured.
One variant of M910, M911 and M913 ensures that the contact tip is always
located in the innermost position. When affected by compressed air via a
connection nipple, the contact tip is pushed out into the measuring position.
The compressed air has to pass through a 0.5 m lter.
A pneumatic returning force is a cost effective way of producing the
contact tip movement, especially when a large number of probes are to
be manipulated at the same time. This also allows fast and safe
automatic charging of components into xtures.
Is used in order to reduce wear and risk of probe breakdown when
charging workpieces manually or by robot into a measuring xture.
M910, M911 and M913 can be delivered with this feature. They have
an axial cable outlet with a nipple for the connection of a vacuum pump.
Pbes Spg pus
Pbes Peumc pus
Pbes cuum ec
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
32/68
0
meem
In applications with very narrow spaces, the extremely compact probes M916
and M917 may be used. In spite of its compact size, the diameter of attach-
ment is 8h6. The cable outlet for M917 is axial, but in M916 it is radial.
Please observe that the zero point is not adjustable in M916.
Cc ps f spces
iP ratinG
All Metem probes are equipped with Viton gaiters to stop moisture and dust entering. Viton is chemically inert and does not
deteriorate when exposed to cutting fluids. All probes fulfil IP65 according to BS 5490:1977 category 2.
CE MarkinG
All our measuring probes are in complete compliance with relevant regulations, including EMC directives 89/336/EEG, but
are not supplied with the CE marking (components are not to be marked). As the recommended carrier frequency is only 10kHz, it is unlikely that any connected interfaces or ampliers will display any EMC problems.
However, if connected to electronic digital circuits with fast transients, the probes may act as antennas. The probes and the
cables are screened, but in such cases the shielding of the complete system installation should be reviewed.
LinEarity
According to current practice, the lin-
earity is stated as a percentage of the
reading. Metem measuring probes are
exceptionally linear, with constant sensi-
tivity all along the measuring range.
MEaSUrinG ForCE
The measuring force stated is valid when
the probe is in a horizontal position.
When used in a vertical position, about
0.1 N should be added to this value,
to take into account the weight of the
moving anchor. In probes equipped with
a gaiter, the springs included have been
adjusted to take into account the elastic-ity of the gaiter (20 %).
MEChaniCaLLy aDJUStaBLE zEro
Point
The possibility of adjusting the probes
zero point above the measuring move-
ment is a valuable feature of all Metem
probes (excl. M916 and M919).
This may be utilized to place the tip in the
optimum measuring position, while the
risk of inuence from workpieces being
moved is diminished.
CoMPatiBLE SEnSitivity
The complete range of Metem measuring
probes, from 1 mm measuring range
and larger, produce the same output
voltage when the scale reading is atmaximum. Because of that, every probe
may be used with the amplier adjusted
to the same nominal sensitivity. (Does
not apply to M910 or M919).
CaBLES
All probes are supplied with 2 m of
screened cable as a standard, and the
cover material chosen provides good
resistance to cutting uids.
iP ratinG
All Metem analogue probes (except the
low force probes) are certied for IP65.
CoMPrESSED air
In order to maximize the life span of the
Metem analogue probes with pneumatic
retract, the compressed air shall be bothclean and dry.
teccl d
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
33/68
31
metem
ProbE hEADSPrInG PUSh
Spring push
Measuring Range mm
Movement outwards from zero point (0.5) mm
Movement inwards from zero point mm
Adjustable zero point
Zero point adjustment range* mm
Repeatability m
Linearity %
Measuring force at the electrical zero point N
Measuring force at the electrical zero point, low force probes N
Supply voltage Veff
Frequency range of the supply voltage kHz
Sensitivity at 10 kHz mV/V/mm 0.5%
Phase shift inputoutput, at 10 kHz
Calibration voltage V
Calibration frequency kHz
Calibration load k
Operating Temperature C
Storage Temperature C
Temperature Coefficient **
IP rating
0.25
0.28
0.30
No.
< 0.10,0.50,5
70
110
220
73.5
0 2
3
10
2
-10 to +80
-40 to +100
7/25/2019 Export Kata Log 2
34/68
32
metem
PROBE HEADPNEUMATIC AND VACUUM
Pneumatic push
Axial cable Type
Art. no.
M911P
8647-01034
M913P
8647-01045
M911V
8647-01026
M910P
8647-01023
M913V
8647-01030
Vacuum retract
Measuring Range mm
Movement outwards from zero point (0.5) mm
Movement inwards from zero point mm
Adjustable zero point
Zero point adjustment range* mm
Repeatability m
Linearity %
Measuring force at 0.4 bar N
Measuring force at 1.0 bar N
Measuring force at 0.3 bar, low force probes N
Measuring force at 1.0 bar, low force probes N
Supply voltage Veff
Frequency range of the supply voltage kHzSensitivity at 10 kHz mV/V/mm 0.5%
Phase shift inputoutput, at 10 kHz
Calibration voltage V
Calibration frequency kHz
Calibration load k
Operating Temperature C
Storage Temperature C
Temperature Coefficient **
IP rating
1.0
1.30
1.70
Yes
1.0
< 0.15,0.50,5
80
280
18
110
110
220
73.50 2
2
10
2
-10 to +80
-40 to +100
7/25/2019 Export Kata Log 2
35/68
meem
MEtEM anaLoGUE ProBES
The working principle of Metem analogue probes is mainly based on two small transformers
sharing the same magnetical core. When the core is moved, the output signal from one of
the transformers increases while the other decreases. The imbalance current is a measureof the core position, and the best linearity is present around the middle point, where the
transformers are almost in balance.
A Metem probe is sensitive, reliable and has good repeatability.
The accepted working method is to measure a perfect workpiece (an adjustment standard)
and then measure the unknown piece. In this way accuracy is derived from the adjustment
standard and the measuring probe is used as a tool of comparison. The standard is to be
measured once a day, or whenever the temperature is changing, in order to efciently cali-
brate away all other variables deriving from xtures, etc. The probe output signal returns to
the original state when the power has been switched off. Metem probes work with alternating
current and the supporting electronics must include modulators/demodulators, ampliers
and controls for zero setting and amplication adjustment.
PErForManCE
The functioning principles for analogue measuring probes have been known for over a
hundred years, and the design has been rened over more than a quarter of a century. The
most important capability parameters are repeatability and linearity. The Metem probes
retain the same sensitivity all along the measuring stroke, and the linearity quoted for the
standard probes includes sensitivity dependent errors.
ContaCt tiPS
Most of the contact tip options with a standard M2.5 thread that are available on the market
t Metem probes. C E Johansson offers a wide range of measuring tips and tip extensions.
The measuring tips that are standard for each probe type are presented below.
Art. no. Description
8647-01019
8647-01036
Carbide ball 3.85 mm
Carbide, radius 1.5 mm
910,911,913
917
For Probe Type
CaBLE EXtEnSionS
The probe cables are 2 meters long as standard. Cable extensions up to 10 meters are
available for large distances between measuring probe and instrument.
Art. no. Type
8648-01024
8648-01025
8648-01026
8648-01027
M964-1
M964-2
M964-3
M964-4
1 m.
2 m.
3 m.
4 m.
Length Art. no. Type
8648-01028
8648-01029
8648-01030
8648-01031
M964-5
M964-6
M964-8
M964-10
5 m.
6 m.
8 m.
10 m.
Length
Fcs d accesses
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
36/68
meem
Meem Dgl Pbes
Metem digital measuring probes are electronic length indicators being utilized for the inspection of diameters, thickness,
conicity etc.
Metem digital probes are used in the same way as common inductive probes. While inductive probes require electronic
adaption and amplification circuits, digital probes are completely integrated with their own electronics, in order to supply a
digital output signal compatible with a computer interface or directly to the display unit Metem 2000.
Digital Masuring Pros
Metem digital measuring probes are an improvement on the Metem inductive probes, and use same probe head (and are
therefore similarly robust). In-stead of utilizing the current balance in a transformer, the in-built coils are parts of frequency
sensitive circuits. When the core is moved, the coil inductance change and cause a frequency alteration. By comparing fre-
quencies the core movement can be calculated. The smart connector for the digital probe contains an error correction
table, which is downloaded during a laser calibration procedure in the factory. The resulting corrected measuring values are
therefore linear all over the measuring range. The digital probe is superior to the inductive probe in all ways.
Sstm ConfigurationMetem digital measuring probes include a probe head and probe electronics, which may be connected directly to a display
unit or to a PC.
Pro Had of Digital Masuring Pros
The probe head in digital probes have the same external size as a Metem inductive probe with similar measuring range, and
may be mounted in the same fixtures with the same holders. The probe heads are available with spring measuring force,
pneumatic measuring force and a variant with low measuring force.
Pro lctronics
The probe head electronics are contained in a smart connector, which is connected to the probe head via a 2 m cable.
Besides managing the control of the measuring probe itself, the electronics contain buffers for connecting each measuring
point to the data bus. This compact, smart connector is connected directly to the digital display unit Metem 2000, or to a
network with the help of a T-Con network unit.
Masmnts with Digital Masing Pos
Even though the digital probe is superior to inductive probes, we still recommend calibration against an adjustment standard.
This will provide assurance against long time drift or errors deriving from expansion or contraction of the supporting xture or
machine. The performance values stated include all mechanical errors in the probe head and possible errors in the electronic
supporting modules.
Asolt Masmnts
Metem digital probes are absolute measuring devices, which means that when switched on they return to the correct initial
value, regardless of any movements that have taken place during the switched-off time span.
Fits fo Sval Applications
The performance of an inductive measuring probe is at its peak at the zero point, which leads to specially adapted xtures for
every type of component to be measured. The digital probe may be used in any position, all over the measuring range. Reset-
ting to different alternative adjustment standards can be performed by simply pushing a button. This allows different compo-
nent types to be measured in the same xture.
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
37/68
35
metem
Probes with Spring push and Pneumatic push
Probes with low measuring force, or Feather Touch, have been designed
especially to gauge delicate surfaces such as car windscreens, TV tubes,
pharmaceutical bottles, electro-mechanical components and plastic parts.
A conventional probe exercises a measuring tip force of about 0.7 N, but
these low force probes only produce 0.18 N, when used in a horizontal
position. This reduction is achieved by exchanging the naturally elastic,
traditional gaiter for a packing ring with small tolerances. In pneumatic
variants the air leakage through this packing ring is less than 0.6 millilitre
per second at an air pressure of one bar (105Pa), which minimizes the
risk of contamination of the surface to be measured. In spite of the minor
air stream, the probe bearing is constantly de-aired. This prevents the ac-
cumulation of dust (the use of ltered air is recommended).
Exchangeable nylon tips are used to protect against surface damage.
When measuring e.g. warm glass, carbide tips may be used. A steel braid
around the cable gives extra protection in such applications where down-
time is critical.
In order to obtain the lowest possible force, low measuring force probes
are available without any spring (type no. with sufx F). The move-
ments outwards and inwards are activated by pneumatic pressure or
vacuum suction respectively, but by adjusting the air pressure all probes
may achieve an identical tip force that is constant all over the measuring
range. If the probe is mounted vertically (tip up), the inwards movement is
accomplished by means of the weight of the moving parts, which elimi-
nates the need of a vacuum.
Probes with springing measuring force
Probes with Pneumatic push
In a conventional pen probe, the measuring tip is pushed outwards by a
built-in spring. When tting the probe in a xture, you have to construct
a mechanism, which brings the probe in contact with the workpiece to be
measured.
A pneumatic measuring force is a cost effective way of producing the
contact tip movement, especially when a large number of probes have to
be manipulated at the same time. This also allows fast and safe automatic
charging of components into xtures.
Low Force Probes
Probes with low measuring force
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
38/68
meem
PROBE HEAD
Low Force Probes Type Art. no.
M947L8647-01063
M948L8647-01067
M949L8647-01071
M947LP8647-01064
M948LP8647-01068
M949LP8647-01072
Spring push Pneumatic push
Standard Probes Type
Art. no.
M946
8647-01060
M947
8647-01061
M948
8647-01065
M949
8647-01069
M947P
8647-01062
M948P
8647-01066
M949P
8647-01070
Calibrated measuring range mm
Total length of stroke mm
Graduation m
Temperature Coefficient (060C) ppm FS/C
Measuring force N
Measuring force, low force probes N
Measuring force at 0.4 bar N
Measuring force at 0.3 bar, low force probes N
Operating Temperature C
Calibration temperature range C
Storage Temperature C
IP rating
1
1.5
0.06
100
70
080
20
-20 to +80
IP65
2
3
0.12
80
70
30
080
20
-20 to +80
IP65
5
6
0.32
100
70
30
080
20
-20 to +80
IP65
10
11
0.64
150
70
30
080
20
-20 to +80
IP65
2
3
0.12
80
80
18
080
20
-20 to +80
IP65
5
6
0.32
100
80
18
080
20
-20 to +80
IP65
10
11
0.64
150
70
18
080
20
-20 to +80
IP65
PROBE ELECTRONICS
Specifications
Accuracy
Reading speed, per second
Input
Output, serial communication
Operating Temperature
Storage Temperature
IP rating
Power supply
All errors, including the probe head
240 (optional buffer for storing 3000 readings)
Directly from the probe head via a two (2) meter cable
Orbit Network Protocol (187.5 kbaud or 9600 baud)
0 - 60C
-20C to 60C
IP65
5V at 0,06A (includes power for head)
SYSTEM ACCURACY
All accuracies stated presuppose regular checks and adjustments
of the system, according to normal calibration practice.
Metem digital probes may be used in any part of the measuring
range, which means that the adjustment master does not have to
correspond exactly to the nominal value. The error values stated
include a factor which takes into consideration the difference
between the adjustment master and the actual workpiece.
Probe head
M946
M947
M948
M949
0.24 m K x 1.0 m
0.24 m K x 1.0 m
0.64 m K x 2.0 m
1.20 m K x 2.0 m
Accuracy
CE MARKING
All our measuring probes are in complete compliance with relevant regulations, including EMC directives 89/336/EEG. As the
recommended carrier frequency is only 5 kHz, it is unlikely that any connected interfaces or ampliers will display any EMC prob-
lems. However, if connected to electronic digital circuits with fast transients, the probes may act as antennas. The probes and
the cables are screened, but in such cases the shielding of the complete system installation should be reviewed.
As accessories, the low force probes are available with nylon or carbide measuring tips.
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
39/68
37
metem
C
M946
M947
M948
M949
Type
28.00
46.00
65.00
89.00
SPRING PUSH
F1
7.45
13.90
17.40
25.40
PNEUMATIC PUSH
LOW FORCE PROBES WITH MEASURING
FORCE SPRING
* When using an angle adapter the Cmeasure is reduced by 3.50 mm
LOW FORCE PROBES -
PNEUMATIC PUSH
8647-01060
8647-01061
8647-01065
8647-01069
Art. no.
C
M947P
M948P
M949P
Type
52.00
71.00
96.00
F1
13.90
17.40
25.40
8647-01062
8647-01066
8647-01070
Art. no.
C *
M947L
M948L
M949L
Type
46.00
65.00
89.00
F1
13.90
17.40
25.40
8647-01063
8647-01067
8647-01071
Art. no.
* When using an angle adapter the Cmeasure is reduced by 3.50 mm
C *
M947LP
M948LP
M949LP
Type
52.00
71.00
96.00
F1
13.90
17.40
25.40
8647-01064
8647-01068
8647-01072
Art. no.
8h6
2,0
F1Fullt utskjuten
F2Helt indragen
C1,0
3,5
30,0
Fully extended
Fully retracted
8h6
F2
Helt indragen
C0,5
3,5
F1Fullt utskjutenFully extended
Fully retracted
8h6
2,0
F1Fullt utskjuten
F2Helt indragen
C4,5
8,0
3,5
3,0
Fully extended
Fully retracted
15,5
21,50
4,3 Max
Vinkeladapter
3,0
8,0
C4,5
8,0
3,5
3,0
8h6
2,0
F1Fullt utskjuten
F2Helt indragen
Fully extended
Fully retracted
Right angle adapter
9.5
21.50
4,3 Max
Vinkeladapter
8h6
2,0
F1Fullt utskjuten
F2Helt indragen
C1,0
3,5
30,0
Fully extended
Fully retracted
Right angle adapter
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
40/68
meem
Meem Gugg pbes
Metem gauging probes are electronic length indicators being used for
the inspection of diameters, thickness, conicity etc.
Metem digital probes are used in the same way as common inductive
probes. While inductive probes require electronic adaption and amplifi-
cation circuits, digital probes are completely integrated with their own
electronics, in order to supply a digital output signal compatible with a
computer interface or directly to the display unit Metem 2000.
Gauging pros
The operating principle of a gauge probe is based on the counting of
pulses when a number of scale markings pass a detector. In a Metem
gauge probe these markings are deposited on a glass scale with low
temperature coefficient (quartz glass) and the markings are counted
with the aid of photo detectors. As the glass substrate is extremely sta-
ble, the density distribution of the gradings will not change. The result isa good inherent long time stability.
Sstm Configuration
The Metem gauge probes include probe head and probe electronics,
which may be connected directly to a display unit or to a PC.
Gaug Pro Had
The gauging probe head is designed to achieve a minimal weight and is
of course compatible with common probes. The outwards motion of the
spindle is accomplished by spring push, pneumatic push or by motor.
Pro lctronics
The probe head electronics are contained in a smart connector, which
is connected to the probe head via a 2 m cable. Besides managing the
control of the measuring probe itself, the electronics contains buffers for
connecting every measuring point to the data bus. This compact, smart
connector is connected directly to the digital display unit Metem 2000, or
to a network with the help of a T-Con network unit.
Highst Accurac of Masurmnt
A Metem gauging probe may be used in any position, all over the measur-
ing range. Resetting to different alternative adjustment standards can beperformed by simply pushing a button. This allows different component
types to be measured in the same xture.
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
41/68
meem
IN A CLASS by ITSeLF
Metem gauge probes have been designed for the measurement of
single components in normal indoor environments, for determin-
ing the position of moving parts, like X-Y-tables, or in multigaugingxtures directly in the production process.
Metem gauge probes are available in four different measuring
lengths, 12 mm, 25 mm, 50 mm and 100 mm (1/2", 1", 2" and 4").
The probes include probe head and probe electronics, connected
via a cable of 2 m length. The electronics in the probe is a compact
smart interface to be connected directly to the digital display
unit, Metem 2000, or to the Orbit-system using a T-CON net-
work unit. Pneumatic and motor driven units are available.
When being used in a measuring laboratory, the probes are sup-
plemented with a digital display unit, Metem 2000. With its unique,
practical design and user friendly display, this measuring instru-
ment is a breakthrough when it comes to providing easy to handle
control and inspection possibilities in a unit with exceptionally
versatile functionality.
Controlling th masuring pro
The outwards motion of the spindle is accomplished by spring
force, pneumatically or by motor. A return spring is included in the
pneumatic options. There is also one type with a free measuring
piston. A distance cable holder is available for the spring variants.
Masurmnts with Gaug pros
Even if the gauge probe is very accurate, we still recommend
calibration against an adjustment standard. This will provide assur-
ance against long-term drift or errors coming from expansion or
contraction of the supporting xture or machine. The performance
values stated include all mechanical errors in the probe head and
possible errors in the electronic supporting modules.
Asolut Masurmnts
Metem gauge probes are absolute measuring devices, which means
that when switched on, they return to the correct initial value,
regardless of any movements that have taken place while
switched-off.
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
42/68
0
meem
PROBE HEAD
Probes, protection rating IP 40 Type
Art. no.
M944M
8647-01057
M945M
8647-01059
M945F
8647-01058
Spring push Motor drive
12.7
0. 5
0.05
2
0.5
20
5
0.2
0.5
20
0.6
0.1
0.5
1.0
8h6
extended
12.7
0. 5
0.05
2
0.5
20
5
0.2
0.5
20
0.6
0.1
0.5
1.0
8h6
retracted
25.4
1.0
0.05
2
0.5
20
5
0.2
0.5
20
0.6
0.1
0.5
1.0
8h6
retracted
50.8
2.0
0.05
2
1.0
40
5
0.2
0.5
20
TBA
1.0
20g6
101.6
4.0
0.05
2
1.0
40
5
0.2
0.5
20
TBA
1.0
20g6
PROBE ELECTRONICS
Specifications
Accuracy
Reading speed, per second
Input
Output, serial communication
Operating Temperature
Storage Temperature
IP rating
Power supply
All errors, including the probe head
1000 (optional buffer for storing 3000 readings)
Directly from the probe head via a two (2) meter cable
Orbit Network Protocol (187.5 kbaud or 9600 baud)
060C
-20C to 60C
IP65
5V at 0,06A (includes power for head)
Total length of stroke mm
inch
Graduation m
micro inch
Accuracy m
micro inch
Position of ref. marking (before upper stop) mm
inch
Reading speed m/s
inch/s
Measuring force - downwards N
upwards N
horizontally N
Acceptable radial force N
Shank
Resting position of spindle
25.4
1.0
0.05
2
0.5
20
5
0.2
0.5
20
0.6
0.1
0.5
1.0
8h6
extended
Pneumatic operation
M944F
8647-01056
Freely Moving Spindle *
50.8
2.0
0.05
2
1.0
40
5
0.2
0.5
20
1.25
1.0
20g6
101.6
4.0
0.05
2
1.0
40
5
0.2
0.5
20
1.25
1.0
20g6
* Freely moving spindle shall only be used in vertical position
Probes, protection rating IP 50 Type Art. no.
Probes, protection rating IP 65 Type
Art. no.
M9408647-01050
M941
8647-01052
M943
8647-01055
M941P
8647-01051
M943P
8647-01054
M9428647-01053
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
43/68
41
metem
64,5
60,8
16,5
M940/941 AND M942/943 M944 AND M945
PROBE ELECTRONICS
AType B CArt. no.
M940
M941P
M942M943P
M944F
M944M
M945F
M945M
8647-01050
8647-01051
8647-010538647-01054
8647-01056
8647-01057
8647-01058
8647-01059
51.0
56.5
76.569.5
100.4
100.4
150.4
150.4
22.4
22.4
34.934.9
25.0
25.0
25.0
25.0
66.0
66.0
92.092.0
154.0
175.5
204.5
226.5
17.0
8,5
8,0 h6
M3 anslut-ning frluftintag/fjrrkontroll
39.4
C
B
A
2m kabel
Spnn-skaft
Lyftarm
M2,5 frmtspets
Lyftarmshllare
8,5
17.26.5
M3 connectionfor air intake/remote control
2 m cable
Lifting leverLifting lever holder
M2,5 forcontact tip
Shank
6,5
39,0
8,0
20,0 g6
54,0
C
Spnnskaft
Lyftarm
M2,5 fr mtspets
B
A
2m kabel
Lyftarmshllare
Shank
2 m cable
Lifting lever holderLifting lever
M2,5 for contact tip
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
44/68
42
CEJ Engineering / Calibration
Engineering
Our measuring systems are characterized by quality, reliability and precision. They shall perform whatever the
customer wishes.
The process of developing and producing a measuring system is only the beginning of a long term relation-ship with our customers. Something which is taken into account already in the basic design is the possibility
to upgrade and develop the systems in order to meet coming demands and new products, naturally in close
cooperation with our customers.
We offer
Help with design, ideas and production of measurement solution for your needs and demands;
Everything from the most simple fixture or set-up, to more advanced systems with measuring control, PLC
and statistics, etc.
Digital and analogue contact probes and non-contact solutions;
Probes well-known to the industry, which helps you to get an optimum plant.
We utilize the best measurement systems and probes in the market.
Together we create exactly what you as customer needs.
Calibration
We perform calibrations of most of the hand gauges available on the market.
Together with cooperation partners we may help you with the great majority of measuring types.
The results are documented in a calibration certificate, which is traceable to national and international length
standards.
Cylindrical gauges and rings Control gauges
Gauge blocks Vernier Calipers
Thread gauges Micrometers
Thread rings Mikrokators Measuring wires Dial gauges
PLC SAFETY SOFTWARE
CONSTRUCTION ENVIRONMENT MEASURING CONTROL
ROBOT SERVICE PRESENTATION
CNC FIXTURE NETWORK
TRANSPORT PROBE AVAILABILITY
SPARE PARTS INDUSTRIAL COMPUTER DEVELOPMENT
tel 1616 08 10 fax 1616 08 90 [email protected]
mailto:[email protected]:[email protected]7/25/2019 Export Kata Log 2
45/68
dcle d guge blck lde
Cleg Dbse Sufce Ples
Dcle s deege, specll pduced f cleg sufce ples.
art. no. Contnt
8070-01001 1 le
DcleDcle Deege
Guge Bl