HUYETT.COM • 785-392-3017
Prices, materials, dimensions, tolerances, designs, and grades subject to change without notice. © 2017 G.L. Huyett
128For detailed specifications and tolerances, visi t Huyett.com.
Description How to IdentifyPerhaps the most popular and widely used radial retaining ring is the E-clip (so named because it is shaped like the letter “E”). Three prongs make contact with the bottom of the groove and provide a shoulder for effective retention of assemblies.
DIN 6799****EXTERNAL – E-CLIP METRIC
Additional attribute data on adjacent page.
Item#
Nominal Size
Shaft Diameter Groove Size Ring Size & Weight Item#
Clearance Supplementary Data Use with ApplicatorDiameter Width Thickness2 Gap Weight Free Outside
DiameterInstalled in Groove
Edge Margin Thrust Load Ring3
Thrust Load Groove (smallest listed Ds)
Allowable Radii &
Chamfers
Max. Loadw/R Max.
or Ch Max.
RPM LimitsStandard Material
Dg Ds Dg Tol. W Tol. T Tol. A Tol. kg/ 1,000
G Ref.
L2 Max.
Y Min.
Pr kN
PgkN
Ds' R/Ch Max.
P'r kNfrom to
DE-008 0.8 1.0 1.4 0.8 -0.040 0.24+0.04/-0.00
0.2 ±0.02 0.58 ±0.040 0.003 DE-008 1.95 2.25 0.4 0.08 0.03 1.2 0.3 0.04 50,000 RRA-708
DE-012 1.2 1.4 2.0 1.2 -0.060 0.34 0.3 ±0.02 1.01 ±0.040 0.009 DE-012 2.90 3.25 0.6 0.12 0.04 1.5 0.4 0.06 47,000 RRA-712
DE-015 1.5 2.0 2.5 1.5 -0.060 0.44 0.4 ±0.02 1.28 ±0.040 0.021 DE-015 3.90 4.25 0.8 0.22 0.07 2.0 0.6 0.11 42,000 RRA-715
DE-019 1.9 2.5 3.0 1.9 -0.060 0.54
+0.05/-0.00
0.5 ±0.02 1.61 ±0.040 0.040 DE-019 4.40 4.80 1.0 0.35 0.10 2.5 0.7 0.17 40,000 RRA-719
DE-023 2.3 3.0 4.0 2.3 -0.060 0.64 0.6 ±0.02 1.94 ±0.040 0.069 DE-023 5.90 6.30 1.0 0.50 0.15 3.0 0.9 0.24 38,000 RRA-723
DE-032 3.2 4.0 5.0 3.2 -0.075 0.64 0.6 ±0.02 2.70 ±0.040 0.088 DE-032 6.90 7.30 1.0 0.65 0.22 4.0 0.9 0.32 35,000 RRA-310
DE-040 4.0 5.0 7.0 4.0 -0.075 0.74 0.7 ±0.02 3.34 ±0.048 0.158 DE-040 8.85 9.30 1.2 0.95 0.25 5.0 1.0 0.47 32,000 RRA-340
DE-050 5.0 6.0 8.0 5.0 -0.075 0.74 0.7 ±0.02 4.11 ±0.048 0.236 DE-050 10.85 11.30 1.2 1.15 0.90 7.0 1.0 0.60 28,000 RRA-605
DE-060 6.0 7.0 9.0 6.0 -0.075 0.74 0.7 ±0.02 5.26 ±0.048 0.255 DE-060 11.80 12.30 1.2 1.35 1.10 8.0 1.1 0.70 25,000 RRA-606
DE-070 7.0 8.0 11.0 7.0 -0.090 0.94 0.9 ±0.02 5.84 ±0.048 0.474 DE-070 13.80 14.30 1.5 1.80 1.25 9.0 1.3 1.00 22,000 RRA-607
DE-080 8.0 9.0 12.0 8.0 -0.09 1.05
+0.08/-0.00
1.00 ±0.03 6.52 ±0.058 0.660 DE-080 15.75 16.3 1.8 2.50 1.42 10.0 1.5 1.25 20,000 RRA-608
DE-090 9.0 10.0 14.0 9.0 -0.09 1.15 1.10 ±0.03 7.63 ±0.058 1.090 DE-090 18.20 18.8 2.0 3.00 1.60 11.0 1.6 1.50 17,000 RRA-609
DE-100 10.0 11.0 15.0 10.0 -0.09 1.25 1.20 ±0.03 8.32 ±0.058 1.250 DE-100 19.70 20.4 2.0 3.50 1.70 12.0 1.8 1.75 15,000 RRA-610
DE-120 12.0 13.0 18.0 12.0 -0.11 1.35 1.30 ±0.03 10.45 ±0.070 1.630 DE-120 22.70 23.4 2.5 4.70 3.10 15.0 1.9 2.30 13,000 RRA-612
DE-150 15.0 16.0 24.0 15.0 -0.11 1.55 1.50 ±0.03 12.61 ±0.070 3.370 DE-150 28.70 29.4 3.0 7.80 7.00 20.0 2.2 3.30 11,000 RRA-615
DE-190 19.0 20.0 31.0 19.0 -0.13 1.80 1.75 ±0.03 15.92 ±0.070 6.420 DE-190 36.50 37.6 3.5 11 10.00 25.0 2.5 3.60 7,600 RRA-619
DE-240 24.0 25.0 38.0 24.0 -0.13 2.05 2.00 ±0.03 21.88 ±0.084 8.550 DE-240 43.50 44.6 4.0 15 13.00 30.0 3.0 4.00 5,500 –
DE-300 30.0 32.0 42.0 30.0 -0.13 2.55 2.50 ±0.03 25.80 ±0.084 13.50 DE-300 51.30 52.6 4.5 23 16.50 36.0 3.5 5.30 4,200 –
DE
TO ORDER DIFFERENT MATERIAL/FINISHES,APPEND SUFFIX WITH YOUR CHOICE:
"NONE" • -BC • -SS • -ZD • -Z3
T
W
DsDg
d
GA
L2
Dg
1. Verify E-shape design and appearance.2. Measure the shaft diameter (Ds).3. Measure the ring outside diameter (G).4. Measure the ring thickness (T).5. Find the part in the chart.
Clearance Diameter Installed In GrooveRing Dimensions Groove Dimensions
T
W
DsDg
d
GA
Visit huyett.com to download Material, Compliance, and RoHS/REACH Certifications* in your Account Order History.* Some exclusions apply
Prices, materials, dimensions, tolerances, designs, and grades subject to change without notice. © 2017 G.L. Huyett
129
Suffix Material/Finish
For detailed specifications and tolerances, visi t Huyett.com.
All dimensions in millimeters.
For hardness specifications, see page 131.
**** DIN 6799 only defines rings in carbon steel. Rings in other materials are dimensioned as defined in technical prints, contact [email protected] for details.
2 For plated rings add 0.05 mm to the listed maximum thickness. Maximum ring thickness will be a minimum of 0.005 mm less than the listed groove width (W) minimum.
3 Sharp corner abutment.
Item#
Nominal Size
Shaft Diameter Groove Size Ring Size & Weight Item#
Clearance Supplementary Data Use with ApplicatorDiameter Width Thickness2 Gap Weight Free Outside
DiameterInstalled in Groove
Edge Margin Thrust Load Ring3
Thrust Load Groove (smallest listed Ds)
Allowable Radii &
Chamfers
Max. Loadw/R Max.
or Ch Max.
RPM LimitsStandard Material
Dg Ds Dg Tol. W Tol. T Tol. A Tol. kg/ 1,000
G Ref.
L2 Max.
Y Min.
Pr kN
PgkN
Ds' R/Ch Max.
P'r kNfrom to
DE-008 0.8 1.0 1.4 0.8 -0.040 0.24+0.04/-0.00
0.2 ±0.02 0.58 ±0.040 0.003 DE-008 1.95 2.25 0.4 0.08 0.03 1.2 0.3 0.04 50,000 RRA-708
DE-012 1.2 1.4 2.0 1.2 -0.060 0.34 0.3 ±0.02 1.01 ±0.040 0.009 DE-012 2.90 3.25 0.6 0.12 0.04 1.5 0.4 0.06 47,000 RRA-712
DE-015 1.5 2.0 2.5 1.5 -0.060 0.44 0.4 ±0.02 1.28 ±0.040 0.021 DE-015 3.90 4.25 0.8 0.22 0.07 2.0 0.6 0.11 42,000 RRA-715
DE-019 1.9 2.5 3.0 1.9 -0.060 0.54
+0.05/-0.00
0.5 ±0.02 1.61 ±0.040 0.040 DE-019 4.40 4.80 1.0 0.35 0.10 2.5 0.7 0.17 40,000 RRA-719
DE-023 2.3 3.0 4.0 2.3 -0.060 0.64 0.6 ±0.02 1.94 ±0.040 0.069 DE-023 5.90 6.30 1.0 0.50 0.15 3.0 0.9 0.24 38,000 RRA-723
DE-032 3.2 4.0 5.0 3.2 -0.075 0.64 0.6 ±0.02 2.70 ±0.040 0.088 DE-032 6.90 7.30 1.0 0.65 0.22 4.0 0.9 0.32 35,000 RRA-310
DE-040 4.0 5.0 7.0 4.0 -0.075 0.74 0.7 ±0.02 3.34 ±0.048 0.158 DE-040 8.85 9.30 1.2 0.95 0.25 5.0 1.0 0.47 32,000 RRA-340
DE-050 5.0 6.0 8.0 5.0 -0.075 0.74 0.7 ±0.02 4.11 ±0.048 0.236 DE-050 10.85 11.30 1.2 1.15 0.90 7.0 1.0 0.60 28,000 RRA-605
DE-060 6.0 7.0 9.0 6.0 -0.075 0.74 0.7 ±0.02 5.26 ±0.048 0.255 DE-060 11.80 12.30 1.2 1.35 1.10 8.0 1.1 0.70 25,000 RRA-606
DE-070 7.0 8.0 11.0 7.0 -0.090 0.94 0.9 ±0.02 5.84 ±0.048 0.474 DE-070 13.80 14.30 1.5 1.80 1.25 9.0 1.3 1.00 22,000 RRA-607
DE-080 8.0 9.0 12.0 8.0 -0.09 1.05
+0.08/-0.00
1.00 ±0.03 6.52 ±0.058 0.660 DE-080 15.75 16.3 1.8 2.50 1.42 10.0 1.5 1.25 20,000 RRA-608
DE-090 9.0 10.0 14.0 9.0 -0.09 1.15 1.10 ±0.03 7.63 ±0.058 1.090 DE-090 18.20 18.8 2.0 3.00 1.60 11.0 1.6 1.50 17,000 RRA-609
DE-100 10.0 11.0 15.0 10.0 -0.09 1.25 1.20 ±0.03 8.32 ±0.058 1.250 DE-100 19.70 20.4 2.0 3.50 1.70 12.0 1.8 1.75 15,000 RRA-610
DE-120 12.0 13.0 18.0 12.0 -0.11 1.35 1.30 ±0.03 10.45 ±0.070 1.630 DE-120 22.70 23.4 2.5 4.70 3.10 15.0 1.9 2.30 13,000 RRA-612
DE-150 15.0 16.0 24.0 15.0 -0.11 1.55 1.50 ±0.03 12.61 ±0.070 3.370 DE-150 28.70 29.4 3.0 7.80 7.00 20.0 2.2 3.30 11,000 RRA-615
DE-190 19.0 20.0 31.0 19.0 -0.13 1.80 1.75 ±0.03 15.92 ±0.070 6.420 DE-190 36.50 37.6 3.5 11 10.00 25.0 2.5 3.60 7,600 RRA-619
DE-240 24.0 25.0 38.0 24.0 -0.13 2.05 2.00 ±0.03 21.88 ±0.084 8.550 DE-240 43.50 44.6 4.0 15 13.00 30.0 3.0 4.00 5,500 –
DE-300 30.0 32.0 42.0 30.0 -0.13 2.55 2.50 ±0.03 25.80 ±0.084 13.50 DE-300 51.30 52.6 4.5 23 16.50 36.0 3.5 5.30 4,200 –
DIN 6799**** EXTERNAL – E-CLIP METRIC
Additional attribute data on adjacent page.
DE
### = CARBON SPRING STEEL, PHOSPHATE###-BC = BERYLLIUM COPPER, PLAIN ###-SS = STAINLESS STEEL, PLAIN###-ZD = CARBON SPRING STEEL, ZINC YELLOW###-Z3 = CARBON SPRING STEEL, ZINC TRIVALENTMaterial/finish combinations may not be available in all sizes. More finishes available, see page 22 for a complete listing.
Y
*The radius “Br” on the load side must not exceed 0.1T
R Max
Ch Max
Br*
Maximum Corner Radius (R Max) & Chamfer (Ch Max)
for Retained Part
*The radius “Br” on the load side must not exceed 0.1T
Edge Margin (Y)
Br
Y
R Max
Ch Max
Br
Y
R Max
Ch Max
STACKED OPTIONS AVAILABLE, SEE HUYETT.COM FOR MORE DETAILS
Prices, materials, dimensions, tolerances, designs, and grades subject to change without notice. © 2017 G.L. Huyett
Also Available AT
DON'T SEE WHAT YOU'RE LOOKING FOR?
Give our Sales Team a call today.
Grease Fittings & Accessories
Machine Keys & Key Stock
Hose Clamps
Engineered Fasteners
Wave & Spring WashersBlind Threaded Inserts
Pins & Wireforms
131For detailed specifications and tolerances, visi t Huyett.com.
Hardness Ranges: JE-clips
Material Size Range ScaleRockwell Hardness
(blank)Carbon Steel,(SAE 1060-1090)
0.8 – 2.53 – 910 – 24
15N30NC
82.5 – 8763 – 7144 – 53
-SSStainless Steel,(PH 15-7 Mo)
0.8 – 2.53 – 910 – 24
15N30NC
82.5 – 86 ♦♦
63 – 69.544 – 51
-BC Beryllium Copper0.8 – 2.53 – 910 – 24
15N30NC
79 – 82 ♦♦
56.5 – 6237 – 43
♦♦ Hardness cannot be checked with any degree of accuracy directly on these rings.
HARDNESS – E-CLIP METRIC
JE
Hardness Ranges: DE-clips
Material Size RangeHardness
HV HRC Lower Scale♦ 15N 30N
(blank)Carbon Steel,(SAE 1060-1090)
0.8 – 1.51.92.3 – 910 – 30
460 – 580460 – 580460 – 580460 – 580
46 – 5446 – 5446 – 5446 – 54
83.5 – 87.5 HR15N♦♦
83.5 – 87.5 HR15N65 – 72 HR30N –
– –
-SSStainless Steel,(PH 15-7 Mo)
0.8 – 1.51.92.3 – 910 – 30
435 – 530435 – 530435 – 530435 – 530
44 – 5144 – 5144 – 5144 – 51
82.5 – 86 HR15N♦♦
82.5 – 86 HR15N63 – 69.5 HR30N –
– –
-SSStainless Steel,(DIN 1.4122 X39CrMo17)
All 470 – 580 47 – 54 – 84 – 87.5 66 – 72
-BC Beryllium Copper
0.8 – 1.51.92.3 – 910 – 30
360 – 415360 – 415360 – 415360 – 415
37 – 4337 – 4337 – 4337 – 43
79 – 82 HR15N♦♦
79 – 82 HR15N56.5 – 62 HR30N –
– –
♦ Where Applicable♦♦ Hardness cannot be checked with any degree of accuracy directly on these rings.
DE
Installation tools available,
see page 256