BMW Motorrad
Rider's ManualF 800 GS
The UltimateRiding Machine
Motorcycle data/dealership details
Motorcycle data
Model
Vehicle identification number
Colour code
Date of first registration
Registration number
Dealership details
Person to contact in Service department
Ms/Mr
Phone number
Dealership address/phone number (com-pany stamp)
Details described or illustratedin this booklet may differ fromthe motorcycle's actual specifica-tion as purchased, the accessor-ies fitted or the national-marketspecification. No claims will beentertained as a result of suchdiscrepancies.Dimensions, weights, fuel con-sumption and performance dataare quoted to the customary tol-erances.The right to modify designs,equipment and accessories isreserved.Errors and omissions excepted.
© 2010 BMW MotorradNot to be reproduced eitherwholly or in part without writtenpermission from BMW Motorrad,After Sales.Printed in Germany.
Important data for refuelling
Fuel
Recommended fuel grade Super unleaded95 ROZ/RON89 AKI
with regular unleaded (RON 91) OE Regular unleaded (slight power- and consumption-relatedrestrictions)91 ROZ/RON87 AKI
Usable fuel capacity approx. 16 l
Reserve fuel approx. 4 l
Tyre pressure
Tyre pressure, front 2.2 bar, one-up, at tyre temperature: 20 °C2.4 bar, two-up and/or with luggage, at tyre temperat-ure: 20 °C
Tyre pressure, rear 2.4 bar, one-up, at tyre temperature: 20 °C2.8 bar, two-up and/or with luggage, at tyre temperat-ure: 20 °C
BMW recommends
Order No.: 01 41 8 521 15106.2010, 4th edition
Welcome to BMW
We congratulate you on yourchoice of a motorcycle fromBMW and welcome you to thecommunity of BMW riders.Familiarise yourself with your newmotorcycle so that you can ride itsafely and confidently in all trafficsituations.Please read this Rider's Manualcarefully before starting to useyour new BMW motorcycle. Itcontains important information onhow to operate the controls andhow to make the best possibleuse of all your BMW's technicalfeatures.In addition, it contains informationon maintenance and care to helpyou maintain your motorcycle'sreliability and safety, as well as itsvalue.If you have questions concerningyour motorcycle, your authorised
BMW Motorrad dealer will gladlyprovide advice and assistance.
We hope that you will enjoy rid-ing your BMW and that all yourjourneys will be pleasant andsafe.
BMW Motorrad.
Table of Contents
You can also consult the index atthe end of this Rider's Manual ifyou want to find a particular topicor item of information.
1 General instructions . . . . 5Overview . . . . . . . . . . . . . . . . . . . . . 6Abbreviations andsymbols . . . . . . . . . . . . . . . . . . . . . . 6Equipment . . . . . . . . . . . . . . . . . . . 7Technical data . . . . . . . . . . . . . . . 7Currency . . . . . . . . . . . . . . . . . . . . . 7
2 General views . . . . . . . . . . . . 9General view, left side . . . . . . . 11General view, right side . . . . . 13Underneath the seat . . . . . . . . 14Underneath the trim pan-el . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Handlebar fitting, left . . . . . . . . 16Handlebar fitting, right . . . . . . . 17Instrument panel . . . . . . . . . . . . 18
3 Status indicators . . . . . . . 21Multifunction display . . . . . . . . 22Meaning of symbols . . . . . . . . . 23Fuel capacity . . . . . . . . . . . . . . . . 23Warning and telltalelights . . . . . . . . . . . . . . . . . . . . . . . . 24Service-due indicator . . . . . . . . 25Kilometres travelled after fueldown to reserve . . . . . . . . . . . . . 25Ambient temperature. . . . . . . . 26Warnings . . . . . . . . . . . . . . . . . . . . 26
4 Operation. . . . . . . . . . . . . . . . 33Ignition switch and steeringlock . . . . . . . . . . . . . . . . . . . . . . . . . 34Electronic immobiliserEWS . . . . . . . . . . . . . . . . . . . . . . . . 35Clock . . . . . . . . . . . . . . . . . . . . . . . . 35Reading . . . . . . . . . . . . . . . . . . . . . 36Stopwatch. . . . . . . . . . . . . . . . . . . 37Lights . . . . . . . . . . . . . . . . . . . . . . . 39Turn indicators . . . . . . . . . . . . . . 40Hazard warning flashers . . . . . 40Emergency off switch (killswitch) . . . . . . . . . . . . . . . . . . . . . . 41
Grip heating . . . . . . . . . . . . . . . . . 41BMW Motorrad ABS . . . . . . . . 42Clutch . . . . . . . . . . . . . . . . . . . . . . . 43Brakes . . . . . . . . . . . . . . . . . . . . . . 43Mirrors . . . . . . . . . . . . . . . . . . . . . . 44Spring preload . . . . . . . . . . . . . . 45Damping . . . . . . . . . . . . . . . . . . . . 46Tyres . . . . . . . . . . . . . . . . . . . . . . . . 46Headlight . . . . . . . . . . . . . . . . . . . . 47Seat . . . . . . . . . . . . . . . . . . . . . . . . . 48Helmet holder . . . . . . . . . . . . . . . 49
5 Riding . . . . . . . . . . . . . . . . . . . . 51Safety instructions . . . . . . . . . . 52Checklist . . . . . . . . . . . . . . . . . . . . 54Starting. . . . . . . . . . . . . . . . . . . . . . 54Running in . . . . . . . . . . . . . . . . . . 56speed . . . . . . . . . . . . . . . . . . . . . . . 57Off-roading . . . . . . . . . . . . . . . . . . 58Brakes . . . . . . . . . . . . . . . . . . . . . . 59Parking your motorcycle . . . . 60Refuelling . . . . . . . . . . . . . . . . . . . 60Secure the motorcycle fortransportation . . . . . . . . . . . . . . . 62
6 Engineering details. . . . . 65Brake system with BMWMotorrad ABS . . . . . . . . . . . . . . . 66
7 Accessories . . . . . . . . . . . . . 69General instructions . . . . . . . . . 70Power sockets . . . . . . . . . . . . . . 70Luggage . . . . . . . . . . . . . . . . . . . . 71Case . . . . . . . . . . . . . . . . . . . . . . . . 71topcase . . . . . . . . . . . . . . . . . . . . . 74Aluminium cases . . . . . . . . . . . . 77Aluminium topcase . . . . . . . . . . 79
8 Maintenance . . . . . . . . . . . . 83General instructions . . . . . . . . . 84Toolkit . . . . . . . . . . . . . . . . . . . . . . . 84Engine oil . . . . . . . . . . . . . . . . . . . 85Brake system . . . . . . . . . . . . . . . 86Coolant . . . . . . . . . . . . . . . . . . . . . . 91Clutch . . . . . . . . . . . . . . . . . . . . . . . 91Rims and tyres . . . . . . . . . . . . . . 92Chain . . . . . . . . . . . . . . . . . . . . . . . . 93Wheels . . . . . . . . . . . . . . . . . . . . . . 95Front-wheel stand . . . . . . . . . 103Bulbs . . . . . . . . . . . . . . . . . . . . . . 104Body panels . . . . . . . . . . . . . . . 110Air filter . . . . . . . . . . . . . . . . . . . . 112
Jump starting . . . . . . . . . . . . . 112Battery . . . . . . . . . . . . . . . . . . . . 114
9 Care . . . . . . . . . . . . . . . . . . . . 119Care products . . . . . . . . . . . . . 120Washing motorcycle. . . . . . . 120Cleaning easily damagedcomponents . . . . . . . . . . . . . . . 120Paint care . . . . . . . . . . . . . . . . . 121Protective wax coating . . . . 122Laying up motorcycle . . . . . 122Restoring motorcycle touse . . . . . . . . . . . . . . . . . . . . . . . . 122
10 Technical data . . . . . . 123troubleshooting chart . . . . . . 124Threaded fasteners . . . . . . . 125Engine . . . . . . . . . . . . . . . . . . . . 127Fuel . . . . . . . . . . . . . . . . . . . . . . . 128Engine oil . . . . . . . . . . . . . . . . . 129Clutch . . . . . . . . . . . . . . . . . . . . . 130Transmission . . . . . . . . . . . . . . 130Rear-wheel drive . . . . . . . . . . 131Running gear . . . . . . . . . . . . . . 131Brakes . . . . . . . . . . . . . . . . . . . . 132Wheels and tyres. . . . . . . . . . 132Electrics . . . . . . . . . . . . . . . . . . . 134
Frame . . . . . . . . . . . . . . . . . . . . . 135Dimensions . . . . . . . . . . . . . . . 136Weights . . . . . . . . . . . . . . . . . . . 136Riding specifications . . . . . . 137
11 Service . . . . . . . . . . . . . . . 139BMW Motorrad service. . . . 140BMW Motorrad servicequality . . . . . . . . . . . . . . . . . . . . . 140BMW Motorrad mobilityservices - roadside assist-ance . . . . . . . . . . . . . . . . . . . . . . . 140BMW Motorrad servicenetwork . . . . . . . . . . . . . . . . . . . 141Maintenance work . . . . . . . . . 141Confirmation of mainten-ance work . . . . . . . . . . . . . . . . . 142Confirmation of service . . . . 147
General instructions
General instructions
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Abbreviations and symbols . . . . . . . . . . 6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Technical data . . . . . . . . . . . . . . . . . . . . . . . 7
Currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15
z Ge
ne
ral i
nst
ruc
tio
ns
OverviewChapter 2 of this Rider's Manu-al will provide you with an initialoverview of your motorcycle. Allmaintenance and repair work onthe motorcycle is documented inChapter 11. This record of themaintenance work you have hadperformed on your motorcycle isa precondition for generous treat-ment of goodwill claims.When the time comes to sellyour BMW, please rememberto hand over this Rider's Manu-al; it is an important part of themotorcycle.
Abbreviations andsymbols
Indicates warnings that youmust comply with for reas-
ons of your safety and the safetyof others, and to protect yourmotorcycle against damage.
Specific instructions onhow to operate, control, ad-
just or look after items of equip-ment on the motorcycle.
Indicates the end of anitem of information.
Instruction.
Result of an activity.
Reference to a page withmore detailed informa-tion.
Indicates the end of apassage relating to spe-cific accessories or itemsof equipment.
Tightening torque.
Item of technical data.
OE Optional extraThe motorcycles are as-sembled complete withall the BMW optional ex-tras originally ordered.
OA Optional accessoryYou can obtain option-al accessories throughyour authorised BMWMotorrad dealer; optionalaccessories have to beretrofitted to the motor-cycle.
EWS Electronic immobiliser.
DWA Anti-theft alarm (Dieb-stahlwarnanlage)
ABS Anti-lock brake system
16
z Ge
ne
ral i
nst
ruc
tio
ns
EquipmentWhen you ordered your BMWmotorcycle, you chose variousitems of custom equipment. ThisRider's Manual describes option-al extras (OE) offered by BMWand selected optional accessor-ies (OA). This explains why themanual may also contain de-scriptions of equipment whichyou have not ordered. Pleasenote, too, that your motorcyclemight not be exactly as illus-trated in this manual on accountof country-specific differences.If your BMW was supplied withequipment not described inthis Rider's Manual, you willfind these features described inseparate manuals.
Technical dataAll dimensions, weights andpower ratings stated in theRider's Manual are quoted to thestandards and comply with thetolerance requirements of theDeutsches Institut für Normunge.V. (DIN). Versions for individualcountries may differ.
CurrencyThe high safety and qualitystandards of BMW motorcyclesare maintained by constantdevelopment work on designs,equipment and accessories.Because of this, your motorcyclemay differ from the informationsupplied in the Rider's Manual.Nor can BMW Motorrad entirelyrule out errors and omissions.We hope you will appreciate thatno claims can be entertained onthe basis of the data, illustrationsor descriptions in this manual.
17
z Ge
ne
ral i
nst
ruc
tio
ns
18
z Ge
ne
ral i
nst
ruc
tio
ns
General views
General views
General view, left side . . . . . . . . . . . . . . . 11
General view, right side . . . . . . . . . . . . . 13
Underneath the seat . . . . . . . . . . . . . . . . 14
Underneath the trim panel . . . . . . . . . . 15
Handlebar fitting, left . . . . . . . . . . . . . . . . 16
Handlebar fitting, right . . . . . . . . . . . . . . 17
Instrument panel . . . . . . . . . . . . . . . . . . . . 18
29
z Ge
ne
ral v
iew
s
210
z Ge
ne
ral v
iew
s
General view, left side1 Power socket ( 70)2 Seat lock ( 48)3 Engine-oil filler neck and
oil dipstick ( 85)
211
z Ge
ne
ral v
iew
s
212
z Ge
ne
ral v
iew
s
General view, right side1 Fuel filler neck ( 60)2 Brake-fluid reservoir, rear
( 90)3 VIN, type plate (on
steering-head bearing,right)
4 Brake-fluid reservoir, front( 89)
5 Coolant level indicator (be-hind side panel) ( 91)
6 Adjuster, spring preload( 45)
7 Adjuster for damping char-acteristic ( 46)
213
z Ge
ne
ral v
iew
s
Underneath the seat1 Stowage
with first-aid kit OA
Location of the first-aid kit2 Standard toolkit ( 84)3 Payload table4 Table of tyre pressures5 Helmet holder ( 49)6 Rider's Manual7 Tool for adjusting spring
preload ( 45)
214
z Ge
ne
ral v
iew
s
Underneath the trimpanel1 Battery ( 114)2 Air-filter housing ( 112)
215
z Ge
ne
ral v
iew
s
Handlebar fitting, left1 Selecting reading in exten-
ded area ( 36)2 with BMW Motorrad
ABS OE
Operating the ABS( 42)
3 Horn4 Flashing turn indicators,
left ( 40)Hazard warning flashers( 40)
5 High-beam headlight andheadlight flasher ( 39)
216
z Ge
ne
ral v
iew
s
Handlebar fitting, right1 Emergency off switch (kill
switch) ( 41)2 Starter button ( 54)3 with heated handlebar
grips OE
Grip heating control( 41)
4 Flashing turn indicators,right ( 40)Hazard warning flashers( 40)
5 Cancel button, flashingturn indicators ( 40)Pushbutton, cancel hazardwarning flashers ( 40)
217
z Ge
ne
ral v
iew
s
Instrument panel1 Warning and telltale lights
( 24)2 Speedometer3 Setting clock ( 35).
with on-board com-puter OE
Operation of the stopwatch( 37)
4 Multifunction display( 22)
5 Select the readings( 36).Resetting tripmeter( 37).
218
z Ge
ne
ral v
iew
s
6 Ambient-light brightnesssensor (for adapting thebrightness of the instru-ment lighting)
with anti-theft alarm OE
Anti-theft alarm telltale light(see the instructions foruse for the anti-theft alarm)
with on-board com-puter OE
Redline warning ( 57)7 Rev. counter
The instrument-clusterlighting has automatic day
and night switchover.
219
z Ge
ne
ral v
iew
s
220
z Ge
ne
ral v
iew
s
Status indicators
Status indicators
Multifunction display . . . . . . . . . . . . . . . . 22
Meaning of symbols . . . . . . . . . . . . . . . . 23
Fuel capacity . . . . . . . . . . . . . . . . . . . . . . . 23
Warning and telltale lights . . . . . . . . . . . 24
Service-due indicator . . . . . . . . . . . . . . . 25
Kilometres travelled after fuel downto reserve . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Ambient temperature . . . . . . . . . . . . . . . 26
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
321
z Sta
tus
ind
ica
tors
Multifunction display1 Trip meter ( 36)2 Warning for engine elec-
tronics ( 30)3 with on-board com-
puter OE
Stopwatch ( 37)4 Time ( 35)5 Warning for coolant tem-
perature ( 29)6 Service due ( 25)7 Values area ( 36)8 with on-board com-
puter OE
Symbols explaining thereadings shown in the val-ues area ( 23)
9 – with on-board computer(optional extra)The horizontal bars indic-ate the level of the coolanttemperature.
322
z Sta
tus
ind
ica
tors
10 – with on-board computer(optional extra)Gear indicator; "N" indic-ates neutral
11 with on-board com-puter OE
Fuel capacity ( 23)12 – with on-board computer
(optional extra)Values area ( 36)
13 a warning is shown in thevalues area ( 26)
Meaning of symbolswith on-board computerOE
distance travelled afterfuel down to reserve in km
( 25)
Average consumption in l/100 km
Average speed in km/h
Current consumption in l/100 km
Ambient temperature in °C( 26)
Fuel capacitywith on-board computerOE
The horizontal bars abovethe fuel-pump symbol in-
dicate the remaining quantity offuel. The top bar is larger than
the others and the quantity offuel it represents is significantlylarger.Once you have refuelled, thegauge briefly shows the originallevel, before the reading is up-dated.
323
z Sta
tus
ind
ica
tors
Warning and telltalelights1 Oil-pressure warning light
( 30)2 with BMW Motorrad
ABS OE
ABS warning light ( 32)3 Warning light for fuel down
to reserve ( 29)4 General warning light, in
combination with warningsin the display ( 26)
5 High-beam headlight tell-tale light
6 Telltale light for right turnindicators
7 Telltale light for neutral8 Telltale light for left turn
indicators
The ABS symbol might dif-fer, depending on the spe-
cifics of national regulations.
324
z Sta
tus
ind
ica
tors
Service-due indicator
If the next service is due in lessthan one month, the date for thenext service 1 is shown brieflyafter the Pre-Ride Check com-pletes. The month is shown as atwo-digit number and the year asa four-digit number, with a colonas separator, so in this examplethe next service is due in March2011.
If the motorcycle covers long dis-tances in the course of the year,under certain circumstances itmight be necessary to have itserviced at a date in advanceof the forecast due date. If thecountdown distance to the odo-meter reading at which a servicewill be due is less than 1000 km,the distance is counted down insteps of 100 km 2 and is shownbriefly after the Pre-Ride Checkcompletes.
If service is overdue, the duedate or the odometer reading atwhich service was due is accom-
panied by the 'General' warninglight showing yellow. The word"Service" remains permanentlyvisible.
If the service-due indicatorappears more than a month
before the service date, the datesaved in the instrument clustermust be adjusted. This situationcan occur if the battery was dis-connected for a prolonged periodof time.If you want to have the date setconsult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Kilometres travelledafter fuel down toreserve
with on-board computerOE
Once the fuel has droppedto the reserve level, the
reading shows the kilometres
325
z Sta
tus
ind
ica
tors
travelled since then. This counteris reset as soon as refuellingbrings the total quantity of fuelon board back above the reservelevel.
Ambient temperaturewith on-board computerOE
When the motorcycle is ata standstill the heat of the
engine can falsify the ambient-temperature reading. If the effectof the engine's heat becomes ex-cessive, -- temporarily appearson the display.If ambient temperature drops be-low 3 °C the temperature dis-play flashes to draw your atten-tion to the risk of black ice form-ing. The display automaticallyswitches from any other modeto the temperature reading whenthe temperature drops below thisthreshold for the first time.
WarningsMode of presentationWarnings are indicated by thecorresponding warning lights.
Warnings that do not have warn-ing lights of their own are indic-ated by 'General' warning light 1showing in combination with atext warning or a warning symbolin the multifunction display. The'General' warning light shows redor yellow, depending on the ur-gency of the warning.
A reading in values area 2that constitutes a warningis accompanied by warningtriangle 3. These warnings canalternate with the odometerreadings ( 36).
The status of the 'General' warn-ing light matches the most ur-gent warning.
The possible warnings are listedon the next page.
326
z Sta
tus
ind
ica
tors
Warnings, overviewWarning light Status indicators Meaning
Lights up yellow + "EWS" appearson the display
Electronic immobiliser active ( 29)
Lights up Fuel down to reserve ( 29)
Lights up red Flashes Coolant temperature too high ( 29)
Lights up yellow Appears on the dis-play
Engine in emergency-operation mode( 30)
Flashes Insufficient engine oil pressure ( 30)
Lights up yellow + "LAMP" ap-pears on the dis-play
Bulb defective ( 30)
"x.x °C" flashes Ice warning ( 31)
Lights up yellow + "dWA" appearson the display
Anti-theft alarm battery flat ( 31)
327
z Sta
tus
ind
ica
tors
Warning light Status indicators Meaning
Flashes ABS self-diagnosis not completed( 32)
Lights up ABS deactivated ( 32)
Lights up ABS fault ( 32)
328
z Sta
tus
ind
ica
tors
Electronic immobiliseractive
General warning light showsyellow.
+ "EWS" appears on thedisplay.
Possible cause:The key being used is not au-thorised for starting, or commu-nication between key and engineelectronics is disrupted.
Remove all other vehicle keysfrom the same ring as the igni-tion key.Use the reserve key.Have the defective key re-placed, preferably by an au-thorised BMW Motorrad dealer.
Fuel down to reserveWarning light for fuel downto reserve shows.
Lack of fuel can result inthe engine misfiring and
cutting out unexpectedly. Mis-firing can damage the catalyticconverter; a hazardous situationcan result if the engine cuts outunexpectedly.Do not run the fuel tank dry.
Possible cause:The fuel tank contains no morethan the reserve quantity of fuel.
Reserve fuel
approx. 4 l
Refuelling ( 60).
Coolant temperature toohigh
General warning light showsred.
The temperature symbolflashes.
Continuing to ride when theengine is overheated could
result in engine damage.Compliance with the informationset out below is essential.
Possible cause:If the coolant level is too low.
Check the coolant level ( 91).If the coolant level is too low:
Topping up coolant ( 91).
Possible cause:The coolant temperature is toohigh.
If possible, ride in the part-loadrange to cool down the engine.In traffic jams, switch off theengine, but leave the ignitionswitched on so that the radiat-or fan continues to operate.If the coolant temperature isfrequently too high, have thefault rectified as soon as pos-sible by a specialist workshop,
329
z Sta
tus
ind
ica
tors
preferably an authorised BMWMotorrad dealer.
Engine in emergency-operation mode
General warning light showsyellow.
Engine symbol appears onthe display.
The engine is running inemergency operating mode.
Full engine power or full enginerpm might not be available andthis can cause hazardous situ-ations, particularly if you attemptto overtake other road users.Engine power level might belower than normal: adapt yourstyle of riding accordingly.
Possible cause:The engine control unit has dia-gnosed a fault. In exceptionalcases, the engine stops and re-fuses to start. Otherwise, the en-
gine runs in emergency operatingmode.
You can continue to ride, butbear in mind that the usual en-gine power might not be avail-able.Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Insufficient engine oilpressure
Warning light for engine-oilpressure flashes.
The oil pressure in the lube-oilsystem is too low. Stop immedi-ately and switch off the engine.
The insufficient oil pres-sure warning does not fulfil
the function of an oil gauge. Theonly way of checking whetherthe oil level is correct is to checkwith the oil dipstick.
Possible cause:The engine-oil level is too low.
Checking engine oil level( 85).
If the oil level is too low:Top up the engine oil ( 86).
Possible cause:The engine-oil pressure is insuffi-cient.
Riding when engine-oilpressure is low can result
in engine damage.Do not continue your journey.
Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Bulb defectiveGeneral warning light showsyellow.
330
z Sta
tus
ind
ica
tors
+ "LAMP" appears on thedisplay.
A defective bulb placesyour safety at risk because
it is easier for other users tooversee the motorcycle.Replace defective bulbs assoon as possible; always carry acomplete set of spare bulbs ifpossible.
Possible cause:Bulb defective.
Visually inspect to ascertainwhich bulb is defective.Replacing low-beam and high-beam headlight bulb ( 104).Replacing parking-light bulb( 106).Replacing brake light and rearlight bulb ( 107).Replacing turn indicator bulbs,front and rear ( 107).
Ice warningwith on-board computerOE
"x.x °C" (ambient temperat-ure) flashes.Possible cause:The air temperature measuredat the motorcycle is lower than3 °C.
The ice warning does notmean that there is no risk
of black ice forming at measuredtemperatures above 3 °C.Always take extra care whentemperatures are low; rememberthat the danger of black ice form-ing is particularly high on bridgesand where the road is in shade.
Ride carefully and think wellahead.
Anti-theft alarm batteryflat
with anti-theft alarm OE
General warning light showsyellow.
+ "dWA" appears on thedisplay.
This error message appearsonly briefly after the pre-
ride check completes.
Possible cause:The integral battery in the anti-theft alarm has lost its entire ori-ginal capacity. There is no assur-ance that the anti-theft alarm willbe operational if the motorcycle'sbattery is disconnected.
Seek the advice of a specialistworkshop, preferably an author-ised BMW Motorrad dealer.
331
z Sta
tus
ind
ica
tors
ABS self-diagnosis notcompleted
with BMW Motorrad ABS OE
ABS warning light flashes.
Possible cause:The ABS function is notavailable, because self-diagnosis did not complete. Themotorcycle has to move forwarda few metres for the wheelsensors to be tested.
Pull away slowly. Bear in mindthat the ABS function is notavailable until self-diagnosis hascompleted.
ABS deactivatedwith BMW Motorrad ABS OE
ABS warning light shows.
Possible cause:The rider has switched off theABS system.
with BMW Motorrad ABS OE
Activating ABS function( 43).
ABS faultwith BMW Motorrad ABS OE
ABS warning light shows.
Possible cause:The ABS control unit has detec-ted a fault. The ABS function isnot available.
You can continue to ride. Bearin mind that the ABS functionis not available. Bear in mindthe more detailed informationon situations that can lead toan ABS fault ( 67).Have the fault rectified asquickly as possible by aspecialist workshop, preferably
an authorised BMW Motorraddealer.3
32
z Sta
tus
ind
ica
tors
Operation
Operation
Ignition switch and steering lock . . . . 34
Electronic immobiliser EWS. . . . . . . . . 35
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Turn indicators . . . . . . . . . . . . . . . . . . . . . . 40
Hazard warning flashers . . . . . . . . . . . . . 40
Emergency off switch (killswitch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Grip heating. . . . . . . . . . . . . . . . . . . . . . . . . 41
BMW Motorrad ABS . . . . . . . . . . . . . . . . 42
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Spring preload . . . . . . . . . . . . . . . . . . . . . . 45
Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Helmet holder . . . . . . . . . . . . . . . . . . . . . . 49
433
z Op
era
tio
n
Ignition switch andsteering lockKeysYou receive two master keys andone spare key. Please consultthe information on the electronicimmobiliser (EWS) if a key is lostor mislaid ( 35).Ignition switch and steering lock,tank filler cap lock and seat lockare all operated with the samekey.
with case OA
with topcaseOA
If you wish you can arrange tohave the cases and the top-case fitted with locks that canbe opened with this key as well.Consult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Switching on ignition
Turn the key to position 1.Parking lights and all functioncircuits switched on.Engine can be started.Pre-ride check is performed.( 55)with BMW Motorrad ABS OE
ABS self-diagnosis isperformed. ( 56)
Switch off the ignition
Turn the key to position 2.Lights switched off.Handlebars not locked.Key can be removed.Electrically powered accessor-ies remain operational for a lim-ited period of time.The battery can be rechargedvia the on-board socket.
Locking handlebarsTurn the handlebars all the wayto left
434
z Op
era
tio
n
Turn the key to position 3,while moving the handlebarsslightly.Ignition, lights and all functioncircuits switched off.Handlebars locked.Key can be removed.
Electronic immobiliserEWSThe motorcycle's electronicsexchange certain continuouslychanging signals with the elec-tronics in the key; these signalsare specific to your motorcycleand they are transmitted via the
ring aerial in the ignition lock.The ignition is not enabled forstarting until the engine controlunit has recognised the key as"authorised" for your motorcycle.
A spare key attached tothe same ring as the ig-
nition key used to start the en-gine could "irritate" the electron-ics, in which case the enablingsignal for starting is not issued.The EWS warning appears in themultifunction display.Always keep the spare key sep-arately from the ignition key.
If you mislay a key you can havethe key in question barred byyour authorised BMW Motorraddealer. In order to have a keybarred you must bring along allthe other keys belonging to themotorcycle.The engine cannot be started bya barred key, but a key that has
been barred can subsequently bereactivated.You can obtain replacement/extrakeys only through an authorisedBMW Motorrad dealer. The keysare part of an integrated securitysystem, so the dealer is under anobligation to check the legitimacyof all applications for replace-ment/extra keys.
ClockSetting clock
Attempting to set the clockwhile riding the motorcycle
can lead to accidents.Set the clock only when the mo-torcycle is stationary.
Switch on the ignition.
435
z Op
era
tio
n
Press and hold down button 1until the hours number 3flashes.Repeatedly press the buttonuntil the hours number is cor-rect.Press and hold down the but-ton until the minutes number 4flashes.Repeatedly press the buttonuntil the minutes number iscorrect.Hold down the button until theminutes number stops flashing.This completes the process.
ReadingSelect the readings
Switch on the ignition.
Press button 2 to select thereading in values area 3.
The following values can be dis-played:
Total kilometres (shown)Tripmeter 1 (Trip I)Tripmeter 2 (Trip II)Warnings, if applicable
with on-board computerOE
Press button 4 to select thereading in values area 5.
The following values can be dis-played:
Ambient temperature (°C)Average speed in km/h
Average consumption in l/100 km
Current consumption in l/100 km
436
z Op
era
tio
n
distance travelled after fueldown to reserve in km
Resetting tripmeterSwitch on the ignition.Select the desired tripmeter.
Press and hold down button 2until the tripmeter reading isreset.
Resetting average valueswith on-board computerOE
Switch on the ignition.
Select average consumption oraverage speed.
Press and hold down button 1until the value shown is reset.
Stopwatchwith on-board computerOE
Stopwatch
You can switch from the odo-meter reading to a stopwatch 3.The readout is in hours, minutes,seconds and tenths of a second,with dots as separators.By swapping the functions ofbutton 2 and the INFO buttonon the handlebar fitting you canmake the stopwatch easier touse (as a lap timer) as you ride.If you swap the functions in thisway the stopwatch and the odo-meter are operated by means ofthe INFO button and you must
437
z Op
era
tio
n
use button 2 to operate the on-board computer.The stopwatch continues to timein the background if you switchback temporarily to the odometerreading. Similarly, the stopwatchcontinues timing if you temporar-ily switch off the ignition.
Operating stopwatch
If necessary, use button 1 toswitch from the odometer tothe stopwatch.
When the stopwatch isstopped, press button 2 tostart timing with the stopwatch.When the stopwatch is running,press button 2 to stop timingwith the stopwatch.Press and hold down button 2to reset the stopwatch.
Changing buttonfunctions
Press button 1 and button 2at the same time and holdthem down until the readingchanges.FLASH (redline warning) ap-pears, along with ON or OFF.Press button 2.LAP (Lap-Timer) and ON orOFF appear.Repeatedly press button 1 untilthe reading shows the modeyou want.
438
z Op
era
tio
n
ON: Stopwatch operated bymeans of the INFO button onthe handlebar fitting.OFF: Stopwatch operated bymeans of button 2 in the in-strument panel.To save the setting, pressbutton 1 and button 2 atthe same time and holdthem down until the readingchanges.
LightsSide lightThe side lights switch on auto-matically when the ignition isswitched on.
The side lights placea strain on the battery.
Do not switch the ignitionon for longer than absolutelynecessary.
Low-beam headlightThe low-beam headlight switcheson automatically when you startthe engine.
When the engine is notrunning you can switch on
the lights by switching on the ig-nition and either switching on thehigh-beam headlight or operatingthe headlight flasher.
High-beam headlight andheadlight flasher
Press top section of switch 1to switch on the high-beamheadlight.
Press bottom section ofswitch 1 to operate theheadlight flasher.
Parking lightSwitch off the ignition.
Immediately after switching offthe ignition, push button 1 andhold it in this position until theparking lights come on.Switch the ignition on and offagain to switch off the parkinglights.
439
z Op
era
tio
n
Turn indicatorsOperating flashing turnindicators
Switch on the ignition.
The turn indicators are can-celled automatically after
you have ridden for approxim-ately 10 seconds, or covered adistance of about 200 m.
Press button 1 to switch onthe left flashing turn indicator.
Press button 2 to switch onthe right flashing turn indicator.
Press button 3 to switch offthe flashing turn indicators.
Hazard warningflashersOperating hazard warningflashers
Switch on the ignition.
The hazard warning flash-ers place a strain on the
battery. Do not use the hazardwarning flashers for longer thanabsolutely necessary.
If you press a turn-indicat-or button with the ignition
switched on, the turn-indicatorfunction is activated instead ofthe hazard warning flashers, andremains active until you releasethe button. The hazard warningflashers recommence flashing assoon as the button is released.
440
z Op
era
tio
n
Press buttons 1 and 2 at thesame time to switch on thehazard warning flashers.Ignition can be switched off.
Press button 3 to switch offthe hazard warning flashers.
Emergency off switch(kill switch)
1 Emergency off switch (killswitch)
Operating the kill switchwhen riding can cause
the rear wheel to lock and thuscause a fall.Do not operate the kill switchwhen riding.
The emergency off switch is akill switch for switching off theengine quickly and easily.
a Normal operating position(run)
b Engine switched off.
Grip heatingwith heated handlebar grips OE
441
z Op
era
tio
n
1 Grip-heating switch
The handlebar grips have two-stage heating. Stage two is forheating the grips quickly: it is ad-visable to switch back to stageone as soon as the grips arewarm. Grip heating can be ac-tivated only when the engine isrunning.
The increase in power con-sumption caused by the
grip heating can drain the bat-tery if you are riding at low en-gine speeds. If the charge levelis low, grip heating is switched
off to ensure the battery's start-ing capability.
2 Heating off.3 50 % heat output (one dot
visible)4 100 % heat output (three
dots visible)
BMW Motorrad ABSwith BMW Motorrad ABS OE
Deactivating ABS functionBring the motorcycle to a stopor, if the motorcycle is at astandstill, switch on the igni-tion.
Press and hold down button 1until the ABS warning lightchanges status.
ABS warning light shows.
Release button 1 within twoseconds.
ABS warning light remainsON.
The ABS function is deactiv-ated.
442
z Op
era
tio
n
Activating ABS function
Press and hold down button 1until the ABS warning lightchanges status.
ABS warning light goes out;if self-diagnosis has not
completed it starts flashing.Release button 1 within twoseconds.
The ABS warning light re-mains off or continues to
flash.
The ABS function is activated.You also have the option ofswitching the ignition off andthen on again.
If you switch the ignition offthen on again and the ABS
light comes back on, there is afault in the ABS.
ClutchAdjusting clutch lever
Attempting to adjust theclutch lever while riding the
motorcycle can lead to accidents.Do not attempt to adjust theclutch lever unless the motor-cycle is at a standstill.
Turn adjusting screw 1clockwise to increase the span
between the clutch lever andthe handlebar grip.Turn adjusting screw 1counter-clockwise to reducethe span between the clutchlever and the handlebar grip.
The adjusting screw is easi-er to turn if you push the
clutch lever forward.
BrakesAdjust the handbrakelever
Changing the position ofthe brake-fluid reservoir can
allow air to penetrate the brakesystem.Do not twist the handlebar fittingor the handlebars.
Attempting to adjust thehandbrake lever while rid-
ing the motorcycle can lead toaccidents.Do not attempt to adjust the
443
z Op
era
tio
n
handbrake lever unless the mo-torcycle is at a standstill.
Turn adjusting screw 1clockwise to increase the spanbetween the brake lever andthe handlebar grip.Turn adjusting screw 1counter-clockwise to reducethe span between the brakelever and the handlebar grip.
The adjusting screw is easi-er to turn if you push the
handbrake lever forward.
MirrorsAdjust the mirrors
Turn the mirror to the correctposition.
Adjusting mirror arm
Push protective cap 1 up overthe threaded fastener on themirror arm.Slacken nut 2.Turn the mirror arm to the ap-propriate position.Tighten the nut to the spe-cified tightening torque, whileholding the mirror arm to en-sure that it does not move outof position.
Locknut (mirror) to clampadapter
20 Nm
444
z Op
era
tio
n
Push the protective cap overthe threaded fastener.
Spring preloadSettingIt is essential to set spring pre-load of the rear suspension tosuit the load carried by the mo-torcycle. Increase spring preloadwhen the motorcycle is heavilyloaded and reduce spring preloadaccordingly when the motorcycleis lightly loaded.
Adjusting spring preloadfor rear wheel
Remove the seat ( 48).
Remove on-board toolkit 1.
Your motorcycle's hand-ling will suffer if you do not
match the spring-preload anddamping-characteristic settings.
Adjust the damping characteristicto suit spring preload.
If you want to increase springpreload, use the tool from theon-board toolkit to turn knob 2clockwise.If you want to reduce springpreload, use the tool from theon-board toolkit to turn knob 2counter-clockwise.
Basic setting of springpreload, rear
Turn the adjusting screwcounter-clockwise as far asit will go (Full load of fuel,with rider 85 kg)
Stow the on-board toolkit in itscorrect position.Installing seat ( 49).
445
z Op
era
tio
n
DampingSettingDamping must be adapted to suitthe surface on which the motor-cycle is ridden and to suit springpreload.
An uneven surface requiressofter damping than a smoothsurface.An increase in spring preloadrequires firmer damping, a re-duction in spring preload re-quires softer damping.
Adjusting damping forrear wheel
Make sure the ground is leveland firm and place the motor-cycle on its stand.
You adjust the damping char-acteristic by turning adjustingscrew 1.
If you want a harder dampingcharacteristic, use a screw-driver to turn adjusting screw 1
in the direction indicated by theH arrow.If you want a softer dampingcharacteristic, use a screw-driver to turn adjusting screw 1in the direction indicated by theS arrow.
Basic setting of rear-sus-pension damping charac-
teristic
Turn adjusting screw as faras it will go clockwise, thenback it off 1 1/2 turns. (Fullload of fuel, with rider 85 kg)
TyresChecking tyre pressure
Incorrect tyre pressures im-pair the motorcycle's hand-
ling characteristics and increasethe rate of tyre wear.Always check that the tyre pres-sures are correct.
446
z Op
era
tio
n
At high road speeds, tyrevalves installed perpen-
dicular to the wheel rim have atendency to open as a result ofcentrifugal force.In order to avoid sudden defla-tion, fit valves installed perpen-dicular to the rim with valve capscomplete with rubber seals andmake sure the valve caps arescrewed firmly on to the valves.
Make sure the ground is leveland firm and place the motor-cycle on its stand.Check tyre pressures againstthe data below.
Tyre pressure, front
2.2 bar (one-up, at tyre tem-perature 20 °C)
2.4 bar (two-up and/or withluggage, at tyre temperature20 °C)
Tyre pressure, rear
2.4 bar (one-up, at tyre tem-perature 20 °C)
2.8 bar (two-up and/or withluggage, at tyre temperature20 °C)
If tyre pressure is too low:Correct tyre pressure.
HeadlightAdjusting headlight fordriving on left/driving onrightIf the motorcycle is ridden in acountry where the opposite ruleof the road applies, its asymmet-ric low-beam headlight will tendto dazzle oncoming traffic.Have the headlight set accord-ingly by a specialist workshop,preferably an authorised BMWMotorrad dealer.
Headlight beam throw andspring preloadHeadlight beam throw is gener-ally kept constant when springpreload is adjusted to suit load.Spring preload adjustment mightnot suffice only if the motorcycleis very heavily loaded. Underthese circumstances, headlightbeam throw has to be adjustedto suit the weight carried by themotorcycle.
Consult a specialist work-shop, preferably an au-
thorised BMW Motorrad dealer,if you are unsure whether theheadlight beam-throw setting iscorrect.
447
z Op
era
tio
n
Adjusting headlight beamthrow
Slacken screws 1 on left andright.Adjust beam throw by tiltingthe headlight slightly about itshorizontal axis.Tighten screws 1 on left andright.
Beam-throw basic setting
Slacken screws 1 on left andright.Tilt the headlight slightlyabout its horizontal axis untilarrowhead 2 is pointing towardmarker 3.Tighten screws 1 on left andright.
SeatRemove the seat
Make sure the ground is leveland firm and place the motor-cycle on its stand.
Turn the key to the left in seatlock 1 and hold it in this pos-ition while pressing down thefront part of the seat.
Lift seat 2 at the front and re-lease the key.
448
z Op
era
tio
n
Remove the seat and placeit, rubber buffers down, on aclean surface.
Installing seat
Engage the seat in holders 3.Firmly press down on the seatat the front.The seat engages with an aud-ible click.
Helmet holderSecuring helmet tomotorcycle
Remove the seat ( 48).
Use a plastic-sheathed steelcable to secure the helmet tohelmet holder 1 on left or right.
If it is attached on the leftside of the motorcycle,
there is a possibility of the hel-
met being damaged by the hotend silencer.If possible, attach the helmeton the right-hand side of themotorcycle.
The helmet catch canscratch the panelling.
Make sure the lock is out of theway when you hook the helmetinto position.
Pass the steel cable throughthe helmet and the holder andposition cable and helmet asshown here.Installing seat ( 49).
449
z Op
era
tio
n
450
z Op
era
tio
n
Riding
Riding
Safety instructions . . . . . . . . . . . . . . . . . . 52
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Running in . . . . . . . . . . . . . . . . . . . . . . . . . . 56
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Off-roading . . . . . . . . . . . . . . . . . . . . . . . . . 58
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Parking your motorcycle . . . . . . . . . . . . 60
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Secure the motorcycle for transport-ation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
551
z Rid
ing
Safety instructionsRider's equipmentDo not ride without the correctclothing. Always wear:
HelmetMotorcycling jacket andtrousersGlovesBoots
This applies even to short jour-neys, and to every season ofthe year. Your authorised BMWMotorrad dealer will be glad toadvise you on the correct cloth-ing for every purpose.
Correct loading
Overloading and imbal-anced loads can adversely
affect the motorcycle's handling.Do not exceed the permissiblegross weight and be sure tocomply with the instructions onloading.
Set spring preload, dampingcharacteristic and tyre pres-sures to suit total weight.with case OA
orwith aluminium case OA
Ensure that the case volumeson the left and right are equal.Make sure that the weight isuniformly distributed betweenright and left.Pack heavy items at the bot-tom of the cases and towardthe inboard side.Note the maximum permissiblepayload and the speed limitfor riding with cases fitted, asstated on the label inside thecase.
with topcaseOA
orwith aluminium topcaseOA
Note the maximum permissiblepayload and the speed limit forriding with topcase fitted, as
stated on the label inside thetopcase.
with tank rucksackOA
Note the maximum permissiblepayload of the tank rucksackand the speed limit for ridingwith a tank rucksack on themotorcycle.
Payload of tank rucksack
max 5 kg
Maximum permissiblespeed for riding with the
tank rucksack fitted to the mo-torcycle
max 130 km/h
with rear softbagOA
Note the maximum permissiblepayload of the rear softbag andthe speed limit for riding with arear softbag on the motorcycle.
552
z Rid
ing
Payload of rear softbag
max 1.5 kg
Maximum permissiblespeed for riding with the
rear softbag fitted to the mo-torcycle
max 130 km/h
SpeedIf you ride at high speed, alwaysbear in mind that various bound-ary conditions can adversely af-fect the handling of your motor-cycle:
Settings of the spring-strut andshock-absorber systemImbalanced loadLoose clothingInsufficient tyre pressurePoor tyre treadEtc.
Risk of poisoningExhaust fumes contain carbonmonoxide, which is colourlessand odourless but highly toxic.
Inhaling the exhaust fumestherefore represents a
health hazard and can evencause loss of consciousness withfatal consequences.Do not inhale exhaust fumes.Do not run the engine in an en-closed space.
Catalytic converterIf misfiring causes unburned fuelto enter the catalytic converter,there is a danger of overheatingand damage.For this reason, observe the fol-lowing points:
Do not run the fuel tank dry.Do not attempt to start or runthe engine with a spark-plugcap disconnected.
Stop the engine immediately ifit misfires.Use only unleaded fuel.Comply with all specified main-tenance intervals.
Unburned fuel will destroythe catalytic converter.
Note the points listed for protec-tion of the catalytic converter.
Risk of overheating
Cooling would beinadequate if the engine
were allowed to idle for a lengthyperiod with the motorcycle ata standstill: overheating wouldresult. In extreme cases, themotorcycle could catch fire.Do not allow the engine to idleunnecessarily. Ride away imme-diately after starting the engine.
553
z Rid
ing
Tampering
Tampering with motor-cycle settings (e.g. elec-
tronic engine management unit,throttle valves, clutch) can causedamages to the components inquestion and lead to failure ofsafety-relevant functions. Dam-age caused in this way is notcovered by the warranty.Do not tamper with the motor-cycle in any way that could resultin tuned performance.
ChecklistUse the following checklist tocheck important functions, set-tings and wear limits before youride off.
BrakesBrake-fluid levels, front and rearClutchDamping-characteristic settingand spring preload
Tyre-tread depth and tyrepressuresCases correctly installed andluggage secured
At regular intervals:Engine oil level (every refuellingstop)Brake-pad wear (every thirdrefuelling stop)Tension and lubrication of thedrive chain
StartingSide standYou cannot start the motorcyclewith the side stand extended anda gear engaged. The engine willswitch itself off if you start it withthe gearbox in neutral and thenengage a gear before retractingthe side stand.
GearboxYou can start the engine whenthe gearbox is in neutral or if youpull the clutch with a gear en-gaged. Do not pull the clutch un-til after you have switched on theignition, as otherwise the enginewill refuse to start.
Starting engine
Kill switch in run position a.
Gearbox lubrication is en-sured only when the engine
is running. Inadequate lubrica-tion can result in damage to thegearbox.
554
z Rid
ing
Do not allow the motorcycle toroll for a lengthy period of time orpush it a long distance with theengine switched off.
Switch on the ignition.Pre-ride check is performed.( 55)with BMW Motorrad ABS OE
ABS self-diagnosis isperformed. ( 56)
Press starter button 1.
If ambient temperatures arevery low, you might find it
necessary to open the throttleslightly when starting the engine.
At ambient temperatures below0 °C, disengage the clutch afterswitching on the ignition.
The start attempt is auto-matically interrupted if bat-
tery voltage is too low. Rechargethe battery before you start theengine, or use jump leads and adonor battery to start.
The engine starts.If the engine refuses to start,consult the troubleshootingchart in the section entitled"Technical data". ( 124)
Pre-ride checkThe instrument panel runs a testof the instruments and the telltaleand warning lights when the ig-nition is switched on: this is thePre-Ride-Check The test is abor-ted if you start the engine beforeit completes.
Phase 1The rev. counter and speedo-meter needles both swing tothe limit values on their scales.At the same time, all the warn-ing lights and telltale lights areswitched on in succession.
Phase 2The 'General' warning lightchanges from yellow to red.
Phase 3The rev. counter and speedo-meter needles both swing backto rest. At the same time, all thewarning lights and telltale lightsswitched on in the initial phaseare switched off in reverse se-quence.
If a needle did not move or if awarning light or telltale light didnot show:
555
z Rid
ing
Some malfunctions cannotbe indicated if one of the
warning lights fails to show.Make sure that all the warningand telltale lights come on in thepre-ride check.
Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
ABS self-diagnosiswith BMW Motorrad ABS OE
BMW Motorrad ABS performsself-diagnosis to ensure its op-erability. Self-diagnosis is per-formed automatically when youswitch on the ignition. The mo-torcycle has to move forward afew metres for the wheel sensorsto be tested.
Phase 1Test of the diagnosis-compat-ible system components withthe motorcycle at a standstill.
ABS warning light flashes.
Phase 2Test of the wheel sensors asthe motorcycle pulls away fromrest.
ABS warning light flashes.
ABS self-diagnosiscompleted
The ABS warning light goesout.
If an indicator showing an ABSfault appears when ABS self-dia-gnosis completes:
You can continue to ride. Bearin mind that the ABS functionis not available.
Have the fault rectified asquickly as possible by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Running inThe first 1000 km
While running in the motor-cycle, vary the throttle openingand engine-speed range fre-quently; avoid riding at constantengine rpm for prolonged peri-ods.Try to do most of your rid-ing during this initial period ontwisting, fairly hilly roads, avoid-ing high-speed main roads andhighways if possible.Comply with the rpm limits forrunning in.
Running-in speed
<5000 min-1
556
z Rid
ing
Do not omit the first inspectionafter 500 - 1200 km.
Brake padsNew brake pads have to beddown before they can achievetheir optimum friction levels. Youcan compensate for this initial re-duction in braking efficiency byexerting greater pressure on thelevers.
New brake pads can ex-tend stopping distance by a
significant margin.Apply the brakes in good time.
TyresNew tyres have a smooth sur-face. This must be roughened byriding in a restrained manner atvarious heel angles until the tyresare run in. This running in pro-cedure is essential if the tyres areto achieve maximum grip.
Tyres do not have their fullgrip when new and there
is a risk of accidents at extremeangles of heel.Avoid extreme angles of heel.
speedwith on-board computerOE
Redline warning
The redline warning indicatesthat engine revolutions havereached the rev. counter's redsegment. The anti-theft alarmtelltale light 1 flashes red to in-
dicate that the engine is red-lining.The signal remains active un-til you shift up or reduce enginespeed. You can activate or deac-tivate the redline warning.
Activating redline warning
Press button 1 and button 2at the same time and holdthem down until the readingchanges.FLASH (redline warning) ap-pears, along with ON or OFF.Repeatedly press button 1 untilthe reading shows the modeyou want.
557
z Rid
ing
ON: Redline warning activated.OFF: Redline warning deactiv-ated.To save the setting, pressbutton 1 and button 2 atthe same time and holdthem down until the readingchanges.
Off-roadingAfter off-roadingBMW Motorrad recommendschecking the following after ridingthe motorcycle off-road:
Tyre pressure
Tyre pressures reduced foroff-road riding impair the
motorcycle's handling character-istics on surfaced roads and canlead to accidents.Always check that the tyre pres-sures are correct.
Brakes
When riding on loose sur-faces or muddy roads, the
brakes may fail to take effectimmediately because of dirt ormoisture on the discs or brakepads.Apply the brakes in good timeuntil the brakes have beencleaned.
The brake pads will wearmore rapidly if you ride fre-
quently on unsurfaced tracks orpoor roads.Check the thickness of the brakepads more frequently and replacethe brake pads in good time.
Spring preload and shock-absorber settings
The off-road settings forspring preload and shock
absorber damping characteristicwill impair the motorcycle's hand-
ling characteristics on surfacedroads.If you have been off-roading, re-member to correct spring preloadand shock-absorber dampingcharacteristics before you returnto surfaced roads.
RimsBMW Motorrad recommendschecking the rims for damageafter off-roading.
Air filter element
Engine damage due toclogged air filter element.
If you ride in dusty terrain checkthe air filter element for cloggingat shorter intervals; clan or re-place as necessary.
Operation in very dusty condi-tions (desert, steppes, or the like)necessitates the use of air filterelements specially designed forconditions of this nature.
558
z Rid
ing
BrakesHow can stoppingdistance be minimised?Each time the brakes are applied,a load distribution shift takesplace with the load shifting for-ward from the rear to the frontwheel. The sharper the motor-cycle decelerates, the more loadis shifted to the front wheel. Thehigher the wheel load, the morebraking force can be transmittedwithout the wheel locking.To optimise stopping distance,apply the front brakes rapidly andkeep on increasing the force youapply to the brake lever. Thismakes the best possible use ofthe dynamic increase in load atthe front wheel. Remember topull the clutch at the same time.In the "panic braking situations"that are trained so frequentlybraking force is applied as rap-idly as possible and with the
rider's full force exerted on thebrake levers; under these circum-stances the dynamic shift in loaddistribution cannot keep pacewith the increase in decelerationand the tyres cannot transmit thefull braking force to the surfaceof the road. Under these circum-stances the front wheel can lockup.
with BMW Motorrad ABS OE
BMW Motorrad ABS preventsthe front wheel from locking up.
Descending mountainpasses
There is a danger of thebrakes fading if you use
only the rear brakes when des-cending mountain passes. Underextreme conditions, the brakescould overheat and suffer severedamage.Use both front and rear brakes,
and make use of the engine'sbraking effect as well.
Wet and dirty brakesWetness and dirt on the brakediscs and the brake pads dimin-ish braking efficiency.Delayed braking action or poorbraking efficiency must bereckoned with in the followingsituations:
Riding in the rain or throughpuddles of water.After the motorcycle has beenwashed.Riding on salted or grittedroads.After work has been carried onthe brakes, due to traces of oilor grease.Riding on dirt-covered surfacesor off-road.
Wetness and dirt result inpoor braking efficiency.
Apply the brakes lightly while
559
z Rid
ing
riding to remove wetness anddirt, or dismount and clean thebrakes.Think ahead and brake in goodtime until full braking efficiency isrestored.
Parking yourmotorcycleSide stand
Switch off the engine.
If the ground is soft or un-even, there is no guaran-
tee that the motorcycle will restfirmly on the stand.Always check that the groundunder the stand is level andfirm.
Extend the side stand andprop the motorcycle on thestand.
The side stand is designedto support only the weight
of the motorcycle.
Do not lean or sit on themotorcycle with the side standextended.
If the camber of the roadwaypermits, turn the handlebars allthe way to the left.On a gradient, the motorcycle
should always face uphill; se-lect 1st gear.
Centre standwith centre stand OE
Switch off the engine.
If the ground is soft or un-even, there is no guaran-
tee that the motorcycle will restfirmly on the stand.Always check that the groundunder the stand is level andfirm.
Excessive movementscould cause the centre
stand to retract, and the
motorcycle would topple inconsequence.Do not lean or sit on the mo-torcycle with the centre standextended.
Extend the centre stand andlift the motorcycle onto thestand.
RefuellingFuel is highly flammable. Anaked flame close to the
fuel tank can cause a fire or ex-plosion.Do not smoke. Never bring anaked flame near the fuel tank.
Fuel expands when hot.Fuel escaping from an
overfilled tank could make its wayonto the road surface. This couldcause a fall.Do not overfill the fuel tank.
560
z Rid
ing
Fuel attacks plastics, whichbecome dull or unsightly.
Wipe off plastic parts immediatelyif they come into contact withfuel.
Leaded fuel will destroy thecatalytic converter.
Use only unleaded fuel.
Make sure the ground is leveland firm and place the motor-cycle on its side stand.
The volume of the tank canbe utilised to the full only
when the motorcycle is proppedon its side stand.
Open the protective cap.
Use the ignition key to unlockthe fuel filler cap and pop thecap open.
Refuel with fuel of the gradestated below; do not fill the
tank past the bottom edge ofthe filler neck.
When refuelling after run-ning on reserve, make sure
that you top up the tank to alevel above reserve, as other-wise the sensor will not be ableto register the new level. If thesensor cannot register the newlevel neither the fuel-level read-ing nor the range readout can beupdated.
Recommended fuelgrade
Super unleaded95 ROZ/RON89 AKI
with regular unleaded (RON91) OE
561
z Rid
ing
Recommended fuelgrade
Regular unleaded (slightpower- and consumption-related restrictions)91 ROZ/RON87 AKI
Usable fuel capacity
approx. 16 l
Reserve fuel
approx. 4 l
Press the fuel tank cap downfirmly to close.Remove the key and close theprotective cap.
Secure the motorcyclefor transportation
Make sure that all componentsthat might come into contactwith straps used to secure themotorcycle are adequately pro-tected against scratching. Useadhesive tape or soft cloths, forexample, for this purpose.
The motorcycle can toppleand fall on its side.
Make sure that the motorcyclecannot topple sideways.
Push the motorcycle onto thetransportation flat and hold it in
position: do not place it on theside stand or centre stand.
Risk of damaging compon-ents.
Take care not to trapcomponents such as brake linesor wires.
At the front, secure the strapsto the bottom fork bridge onboth sides and tighten thestraps.
562
z Rid
ing
At the rear, secure the strapsto the rear frame on both sidesand tighten the straps.Tighten all the straps uniformly;the motorcycle's suspensionshould be compressed astightly as possible front andrear.
563
z Rid
ing
564
z Rid
ing
Engineering details
Engineering details
Brake system with BMW MotorradABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
665
z En
gin
ee
rin
g d
eta
ils
Brake system withBMW Motorrad ABS
with BMW Motorrad ABS OE
How does ABS work?The amount of braking force thatcan be transferred to the roaddepends on factors hat includethe coefficient of friction of theroad surface. Loose stones, iceand snow or a wet road all havemuch lower coefficients of fric-tion than a clean, dry asphalt sur-face. The lower the coefficientof friction, the longer the brakingdistance.If the rider increases brakingpressure to the extent that brak-ing force exceeds the maxim-um transferrable limit, the wheelsstart to lock and the motorcycleloses its directional stability; a fallis imminent. Before this situationcan occur, ABS intervenes andadapts braking pressure to themaximum transferrable braking
force, so the wheels continueto turn and directional stabilityis maintained irrespective of thecondition of the road surface.
What are the effects ofsurface irregularities?Humps and surface irregularit-ies can cause the wheels to losecontact temporarily with the roadsurface; if this happens the brak-ing force that can be transmit-ted to the road can drop to zero.If the brakes are applied underthese circumstances the ABShas to reduce braking force toensure that directional stabilityis maintained when the wheelsregain contact with the road sur-face. At this instant the BMWMotorrad ABS must assume anextremely low coefficient of fric-tion, so that the wheels will con-tinue to rotate under all imagin-able circumstances, because thisis the precondition for ensuring
directional stability. As soon asis registers the actual circum-stances, the system reacts in-stantly and adjusts braking forceaccordingly to achieve optimumbraking.
Rear wheel liftUnder very severe and suddendeceleration, however, undercertain circumstances it is pos-sible that the BMW MotorradABS will be unable to preventthe rear wheel from lifting clearof the ground. If this happensthe outcome can be a highsidingsituation in which the motorcyclecan flip over.
Severe braking can causethe rear wheel to lift off the
ground.When you brake, bear in mindthat ABS control cannot be reliedon in all circumstances to preventthe rear wheel from lifting clear ofthe ground.
666
z En
gin
ee
rin
g d
eta
ils
What is the designbaseline for BMWMotorrad ABS?Within the limits imposed byphysics, BMW Motorrad ABS en-sures directional stability on anysurface. The system is not op-timised for special requirementsthat apply under extreme com-petitive situations off-road or onthe track.
Special situationsThe speeds of the front and rearwheels are compared as onemeans of detecting a wheel'sincipient tendency to lock. If thesystem registers implausible val-ues for a lengthy period the ABSfunction is deactivated for safetyreasons and an ABS fault mes-sage is issued. Self-diagnos-is has to complete before faultmessages can be issued.In addition to problems with theBMW Motorrad ABS, exceptional
riding conditions can lead to afault message being issued.Exceptional ridingconditions:
Riding for a lengthy period withthe front wheel lifted off theground (wheelie).Rear wheel rotating with themotorcycle held stationary byapplying the front brake (burn-out).Heating up with the motorcycleon the centre stand or an auxil-iary stand, engine idling or witha gear engaged.Rear wheel locked for a lengthyperiod, for example while des-cending off-road.
If a fault message is issued onaccount of exceptional ridingconditions as outlined above, youcan reactivate the ABS functionby switching the ignition off andon again.
What significancedevolves on regularmaintenance?
Invariably, a technical sys-tem cannot perform beyond
the abilities dictated by its levelof maintenance.In order to ensure that the BMWMotorrad ABS is always main-tained in optimum condition, itis essential for you to complystrictly with the specified inspec-tion intervals.
Reserves for safetyThe potentially shorter brakingdistances which BMW MotorradABS permits must not be usedas an excuse for careless riding.ABS is primarily a means of en-suring a safety margin in genuineemergencies.Take care when cornering. Whenyou apply the brakes on a corner,the motorcycle's weight and
667
z En
gin
ee
rin
g d
eta
ils
momentum take over and evenBMW Motorrad ABS is unable tocounteract their effects.
668
z En
gin
ee
rin
g d
eta
ils
Accessories
Accessories
General instructions . . . . . . . . . . . . . . . . . 70
Power sockets . . . . . . . . . . . . . . . . . . . . . . 70
Luggage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
topcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Aluminium cases. . . . . . . . . . . . . . . . . . . . 77
Aluminium topcase . . . . . . . . . . . . . . . . . 79
769
z Ac
ce
sso
rie
s
General instructionsBMW Motorrad recommendsthe use of parts and accessoriesfor your motorcycle that are ap-proved by BMW for this purpose.Genuine BMW parts and ac-cessories and other productswhich BMW has approved canbe obtained from your authorisedBMW Motorrad dealer, togetherwith expert advice on their install-ation and use.These parts and products havebeen tested by BMW for safety,function and suitability. BMWaccepts product liability for them.Conversely, BMW is unable toaccept any liability whatsoeverfor parts and accessories which ithas not approved.Also bear in mind the informa-tion on the effect of wheel sizeon suspension-control systems( 95).
BMW Motorrad cannotexamine or test each
product of outside origin toensure that it can be used onor in connection with BMWmotorcycles without constitutinga safety hazard. Country-specificofficial authorisation does notsuffice as assurance. Testsconducted by these instancescannot make provision for alloperating conditions experiencedby BMW motorcycles and,consequently, they are notsufficient in some circumstances.Use only parts and accessor-ies approved by BMW for yourmotorcycle.
Whenever you are planningmodifications, comply with all thelegal requirements. Make surethat the motorcycle does notinfringe the national road-vehicleconstruction and use regulationsapplicable in your country.
Power socketsNotes on use of power sockets:
automatic shutdownPower sockets are shut downautomatically under the followingcircumstances:
If battery charge state is toolow to maintain the motor-cycle's start capabilityIf maximum load capability asstated in the technical data isexceededWhen the engine is beingcranked on the starter
Operating electricalaccessoriesYou can start using electrical ac-cessories only when the ignitionis switched on. The accessoryremains operational if the igni-tion is subsequently switched off.The power sockets are switchedoff approximately 15 minutesafter the ignition is switched off,
770
z Ac
ce
sso
rie
s
in order to prevent overloading ofthe on-board electrics.
Cable routingThe cables from the power sock-ets to the auxiliary devices mustbe routed in such a way thatthey:
Do not impede the riderDo not restrict the steeringangle or obstruct handlingCannot be trapped
LuggageLashing luggage
Loop the luggage straps overthe bar between the motor-cycle and stops 1.
Position luggage strap 2 asshown here with a stuffbag asexample.Check that the luggage is se-cure.
Casewith case OA
771
z Ac
ce
sso
rie
s
Opening cases
Turn key 1 in the case lock toright angles with the forwarddirection of travel.Press and hold down yellowlatch 2 and pull up carryhandle 3.
Push yellow button 4 downand at the same time open thelid of the case.
Closing casesTurn the lock with the key untilit is at right angles to the for-ward direction of travel.Close the case lid.The lid engages with an aud-ible click.
Closing the carry handlewhile the case lock is in
line with the forward direction oftravel can result in damage to thelocking tongue.Make sure that the case lock isat right angles to the forward dir-ection of travel when you closethe carry handle.
Close carry handle 3.Turn the key in the case lockin line with the forward direc-tion of travel and remove thekey from the lock.
772
z Ac
ce
sso
rie
s
Adjusting case volumeOpen the case and remove allits contents.
Engage pivot lever 1 at the toplimit position to set the case tominimum volume.Engage pivot lever 1 at thebottom limit position to set thecase to maximum volume.Close the case.
Remove the cases
Turn key 1 in the case lock toright angles with the forwarddirection of travel.Press and hold down yellowlatch 2 and pull up carryhandle 3.
Pull red release lever 4 up.Latching flap 5 pops up.Fully open the latching flap.Take a firm grip of the handleand lift the case out of theholder.
773
z Ac
ce
sso
rie
s
Installing cases
Fully open latching flap 5, if ne-cessary pulling up red releaselever 4.
Position the case in case car-rier 6, then pivot it until it isseated at mount 7.
Push latching flap 5 down asfar as it will go and hold it inthis position.
Push red release lever 4 down.Latching flap 5 engages.Close the carry handle.Turn the key parallel with thedirection of travel and remove.
topcasewith topcaseOA
Opening topcase
Turn key 1 in the topcase lockto the vertical position.Press and hold down yellowlatch 2 and pull out carryhandle 3.
774
z Ac
ce
sso
rie
s
Push yellow button 4 forwardand at the same time push thetopcase lid up.
Close the topcase
Press down firmly on the top-case lid to close.
Closing the carry handlewhile the topcase lock is
horizontal can result in damageto the locking tongue.Make sure that the topcase lockis vertical when you close thecarry handle.
Close carry handle 3.The handle engages with anaudible click.Turn the key in the topcaselock to the horizontal positionand remove the key from thelock.
Adjusting topcase volumeOpen the topcase and removeall its contents.
Engage pivot lever 1 at thefront limit position to set thecase to maximum volume.Engage pivot lever 1 at therear limit position to set thecase to minimum volume.Close the topcase.
775
z Ac
ce
sso
rie
s
Removing topcase
Turn key 1 in the topcase lockto the vertical position.Hold down yellow latch 2 andpush carry handle 3 down.
Pull red lever 4 back as far as itwill go.Latching flap 5 pops up.Fully open latching flap 5.Take a firm grip of the handleand lift the topcase out of theholder.
Installing topcase
Fully open latching flap 5, ifnecessary pulling red releaselever 4 to the rear.
776
z Ac
ce
sso
rie
s
Engage the topcase in frontholders 6 of the topcase carrierplate.Press the topcase onto thetopcase carrier plate at therear.
Push latching flap 5 fullyclosed and hold it in thisposition.Push red release lever 4 for-ward.The latching flap engages.Close the carry handle.Turn the key to the horizontalposition and remove.
Aluminium caseswith aluminium case OA
Opening cases
Turn key 1 counter-clockwise.
The case lid can be openedat either the left or the right
latch.
Push lock housing 2 up to dis-engage latch toggle 3.Pull latch toggle 3 to the sideand open the lid.
777
z Ac
ce
sso
rie
s
Closing cases
Close the case lid.Hold latch toggle 3 in positionon the lid.Push lock housing 2 down,making sure that the latchtoggle grips firmly in the lid.To secure the lock, turn thekey clockwise and remove.
Removing case lidOpen one latch of the case lid.
Disengage retainer 1.Close the case lid.Open the second catch of thecase lid.Remove the case lid.
Installing case lidPlace the case lid on the case.Close one latch of the case lid.Using the locked side as ahinge, open the case lid.
Engage retainer 1.Close the case lid.Close the second latch of thecase lid.
Remove the cases
Turn key 1 counter-clockwise.
778
z Ac
ce
sso
rie
s
Push lock housing 2 to oneside to disengage latchtoggle 3.Pull latch toggle 3 to the side,while holding the case in posi-tion.
The left case and the casecarrier can become hot on
long rides.Allow the case and the case car-rier to cool down before remov-ing the case.
Pull the case back as far as itwill go and then out to remove.
Installing cases
Set the case on the case carri-er and push it forward in sucha way that mounts on case car-rier 5 and on case 4 engageeach other.
Seat latch toggle 3 on the casecarrier, while holding the casein position.Push lock housing 2 to theside, making sure that the latchtoggle grips firmly on the carri-er.Turn the key clockwise andremove.
Aluminium topcasewith aluminium topcaseOA
779
z Ac
ce
sso
rie
s
Topcase and off-roadingIt is advisable to either removethe topcase or fit the backrestcushion available as an optionalaccessory if you intend off-road-ing.
Opening topcase
Turn key 1 counter-clockwise.Push lock housing 2 up to dis-engage latch toggle 3.Pull latch toggle 3 back andopen the lid.
Closing topcase
Close the topcase lid.Hold latch toggle 3 in positionon the lid.Push lock housing 2 down,making sure that the latchtoggle grips firmly in the lid.To secure the lock, turn thekey clockwise and remove.
Removing topcase
Turn key 1 counter-clockwise.Push lock housing 2 down toengage latch toggle 3.Pull latch toggle 3 back.Pull the topcase to the rear andthen lift it up to remove.
780
z Ac
ce
sso
rie
s
Installing topcase
Set the topcase on the top-case rack and push it forwardin such a way that mounts ontopcase rack 5 and on top-case 4 engage each other.
Hold latch toggle 3 in positionon the topcase carrier.Push lock housing 2 up, mak-ing sure that the latch togglegrips firmly on the carrier.To secure the lock, turn thekey clockwise and remove.
781
z Ac
ce
sso
rie
s
782
z Ac
ce
sso
rie
s
Maintenance
Maintenance
General instructions . . . . . . . . . . . . . . . . . 84
Toolkit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Brake system . . . . . . . . . . . . . . . . . . . . . . . 86
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Rims and tyres . . . . . . . . . . . . . . . . . . . . . . 92
Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Front-wheel stand . . . . . . . . . . . . . . . . . 103
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Body panels . . . . . . . . . . . . . . . . . . . . . . . 110
Air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Jump starting . . . . . . . . . . . . . . . . . . . . . . 112
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
883
z Ma
inte
na
nc
e
General instructionsThe "Maintenance" chapter de-scribes straightforward proced-ures for checking and replacingcertain wear parts.Special tightening torques are lis-ted as applicable. The tighteningtorques for the threaded fasten-ers on your motorcycle are listedin the section entitled "Technicaldata".You will find information on moreextensive maintenance and repairwork in the Repair Manual onDVD for your motorcycle, whichis available from your authorisedBMW Motorrad dealer.
Some of the work calls for spe-cial tools and a thorough know-ledge of motorcycle technology.If you are in doubt consult a spe-cialist workshop, preferably yourauthorised BMW Motorrad deal-er.
ToolkitStandard toolkit
1 Screwdriver handle2 Reversible screwdriver
bladeWith star-head and plain-tip ends
Replacing turn indicat-or bulbs, front and rear( 107).Replacing number-platelight bulbs ( 109).Removing battery( 115).
3 Open-ended spannerWidth across flats 17
Adjusting mirror arm( 44).
4 Torx wrench, T40Adjusting headlight beamthrow ( 48).
5 Reversible screwdriverbladeWith star-head and TorxT25
Remove the centre trimpanel ( 110).
Tools service setwith service toolkitOA
884
z Ma
inte
na
nc
e
BMW Motorrad has assembleda tools service set that is idealfor carrying out extended servicework (e.g. removing and installingwheels) on this motorcycle. Youcan obtain the tools set fromyour authorised BMW Motorraddealer.
Engine oilChecking engine oil level
The engine can seize if theoil level is low, and this can
lead to accidents.Always make sure that the oillevel is correct.
The oil level varies with thetemperature of the oil. The
higher the temperature, the high-er the level of oil in the sump.Checking the oil level with theengine cold or after no more thana short ride will lead to misinter-pretation; this in turn, means thatthe engine will be operated withthe incorrect quantity of oil.In order to ensure that the en-gine oil level is read correctly,check the oil level only after alengthy trip.
Wipe the area around the oilfiller neck clean.Allow the engine to idle untilthe fan starts up, then allow itto idle one minute longer.Switch off the engine.Make sure the engine is at op-erating temperature and holdthe motorcycle upright.with centre stand OE
Check that the engine is at op-erating temperature, make sure
the ground is level and firmand place the motorcycle on itscentre stand.
Remove oil dipstick 1.
Use a dry cloth to wipe gaugelength 2 clean
885
z Ma
inte
na
nc
e
Seat the oil dipstick on the oilfiller neck, but do not engagethe threads.Remove the oil dipstick andcheck the oil level.
Engine oil, specified level
Between MIN and MAXmarks
If the oil level is below the MINmark:
Top up the engine oil ( 86).
If the oil level is above the MAXmark:
Have the oil level correctedby a specialist workshop,preferably an authorised BMWMotorrad dealer.
Install the oil dipstick.
Top up the engine oilMake sure the ground is leveland firm and place the motor-cycle on its stand.Wipe the area around the fillerneck clean.
Remove oil dipstick 1.
Damage to the enginecan result if it is operated
without enough oil, but the samealso applies if the oil level is toohigh.Always make sure that the oillevel is correct.
Top up the engine oil to thespecified level.Checking engine oil level( 85).Install the oil dipstick.
Brake systemCheck operation of thebrakes
Pull the handbrake lever.The pressure point must beclearly perceptible.Press the footbrake lever.The pressure point must beclearly perceptible.
886
z Ma
inte
na
nc
e
If pressure points are not clearlyperceptible:
Incorrect working practicesendanger the reliability of
the brakes.Have all work on the brake sys-tem undertaken by trained andqualified specialists.
Have the brakes checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Check the front brake padthickness
Make sure the ground is leveland firm and place the motor-cycle on its stand.
Visually inspect the left andright brake pads to ascertaintheir thickness. Viewing direc-tion: between wheel and frontsuspension toward brake cal-ipers 1.
Brake-pad wear limit,front
min 1.0 mm (Friction padonly, without backingplate. The wear indicators(grooves) must be clearlyvisible.)
If the wear indicating marks areno longer clearly visible:
Brake pads worn past theminimum permissible thick-
ness can cause a reduction inbraking efficiency and undercertain circumstances they can
887
z Ma
inte
na
nc
e
cause damage to the brake sys-tem.In order to ensure the dependab-ility of the brake system, do notpermit the brake pads to wearpast the minimum permissiblethickness.
Have the brake pads replacedby a specialist workshop,preferably an authorised BMWMotorrad dealer.
Checking rear brake padthickness
Make sure the ground is leveland firm and place the motor-cycle on its stand.
Visually inspect the brake padsto ascertain their thickness.Viewing direction: from the reartoward brake caliper 1.
Brake-pad wear limit,rear
min 1.0 mm (Friction padonly, without backing plate.The wear indicators must beclearly visible.)
If the wear indicating mark is nolonger visible:
Brake pads worn past theminimum permissible thick-
ness can cause a reduction inbraking efficiency and undercertain circumstances they can
888
z Ma
inte
na
nc
e
cause damage to the brake sys-tem.In order to ensure the dependab-ility of the brake system, do notpermit the brake pads to wearpast the minimum permissiblethickness.
Have the brake pads replacedby a specialist workshop,preferably an authorised BMWMotorrad dealer.
Check the brake-fluidlevel, front brakes
A low fluid level in thebrake reservoir can allow air
to penetrate the brake system.This significantly reduces brakingefficiency.Check the brake-fluid level atregular intervals.
Make sure the ground is leveland firm and hold the motor-cycle upright.
with centre stand OE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Move the handlebars to thestraight-ahead position.
Check the brake fluid level infront reservoir 1.
Wear of the brake padscauses the brake fluid level
in the reservoir to sink.
Brake fluid level, front(visual inspection)
DOT4 brake fluid
It is impermissible for thebrake fluid level to drop be-low the MIN mark.
If the brake fluid level drops be-low the permitted level:
Have the defect rectified asquickly as possible by a spe-cialist workshop, preferablyan authorised BMW Motorraddealer.
889
z Ma
inte
na
nc
e
Check the brake-fluidlevel, rear brakes
A low fluid level in thebrake reservoir can allow air
to penetrate the brake system.This significantly reduces brakingefficiency.Check the brake-fluid level atregular intervals.
Make sure the ground is leveland firm and hold the motor-cycle upright.with centre stand OE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Check the brake fluid level inrear reservoir 1.
Wear of the brake padscauses the brake fluid level
in the reservoir to sink.
Brake fluid level, rear(visual inspection)
DOT4 brake fluid
It is impermissible for thebrake fluid level to drop be-low the MIN mark.
If the brake fluid level drops be-low the permitted level:
Have the defect rectified asquickly as possible by a spe-cialist workshop, preferablyan authorised BMW Motorraddealer.
890
z Ma
inte
na
nc
e
CoolantCheck the coolant level
Make sure the ground is leveland firm and place the motor-cycle on its stand.
Check the coolant level in ex-pansion tank 1. Viewing dir-ection: From in front, betweenwindscreen and right side pan-el.
Coolant, specified level
Antifreeze
between MIN and MAXmarks on the expansion tank
If the coolant drops below thepermitted level:
Top up the coolant.
Topping up coolant
Open cap 1 of the expansiontank.Using a suitable funnel, top upwith coolant until the level iscorrect.Close the cap of the expansiontank.
ClutchChecking clutch operation
Pull the clutch lever.The pressure point must beclearly perceptible.
891
z Ma
inte
na
nc
e
If the pressure point is not clearlyperceptible:
Have the clutch checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Check the clutch playTurn the handlebars all the wayto left
Pull clutch cable 1 as far aspossible away from the clutchlever.
Measure clutch play Abetween the handlebar fittingand the clutch cable.
Clutch play
3 mm (Handlebars turnedfully left, between handlebarfitting and clutch cable)
Clutch play is out of tolerance:Adjusting clutch play ( 92).
Adjusting clutch play
Slacken nut 3.To increase clutch play: screwnut 2 up.
To reduce clutch play: screwnut 2 down.Check the clutch play ( 92).Repeat the steps in this pro-cedure until clutch play is setcorrectly.Tighten nut 3.
Rims and tyresChecking rims
Make sure the ground is leveland firm and place the motor-cycle on its stand.Visually inspect the rims fordefects.Have damaged rims checkedand, if necessary, replaced by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Checking spokesMake sure the ground is leveland firm and place the motor-cycle on its stand.
892
z Ma
inte
na
nc
e
Draw the handle of a screw-driver or a similar instrumentacross the spokes and listento the notes of the individualspokes.
If the notes vary:Have the spokes checked by aspecialist workshop, preferablyan authorised BMW Motorraddealer.
Check the tyre treaddepth
Your motorcycle's handlingand grip can be impaired
even before the tyres wear tothe minimum tyre tread depthpermitted by law.Have the tyres changed in goodtime before they wear to theminimum permissible treaddepth.
Make sure the ground is leveland firm and place the motor-cycle on its stand.
Measure the tyre tread depthin the main tread grooves withwear marks.
Tyres have wear indicatorsintegrated into the main
tread grooves. The tyre is wornout when the tyre tread has worndown to the level of the marks.The locations of the marks areindicated on the edge of the tyre,e.g. by the letters TI, TWI or byan arrow.
If the tyre tread is worn to minim-um:
Replace tyre or tyres, as applic-able.
ChainLubricating chain
Dirt, dust and inadequatelubrication will result in ac-
celerated wear and significantlyshorten the drive chain's usefullife.
Clean and lubricate the drivechain at regular intervals.
Lubricate the drive chain every1000 km at the latest. Lubric-ate the chain more frequently ifthe motorcycle is ridden in wet,dusty or dirty conditions.
Switch the ignition off and se-lect neutral.Clean the drive chain with asuitable cleaning product, dry itand apply chain lubricant.Wipe off excess lubricant.
Checking chain sagMake sure the ground is leveland firm and place the motor-cycle on its stand.Turn the rear wheel until itreaches the position with thelowest amount of chain sag.
893
z Ma
inte
na
nc
e
Use a screwdriver to push thechain up and down and meas-ure difference A.
Chain deflection
35...45 mm (Motorcycle withno weight applied, supportedon its side stand)
If measured value is outside per-mitted tolerance:
Adjusting chain sag ( 94).
Adjusting chain sagMake sure the ground is leveland firm and place the motor-cycle on its stand.
Slacken quick-release axlenut 1.Slacken locknuts 2 on left andright.Use adjusting screws 3 on leftand right to adjust chain sag.Checking chain sag ( 93).Make sure that scale read-ings 4 are the same on left andright.
Tighten locknuts 2 on left andright.
Locknut of the final-drivechain tensioning screw
19 Nm
Tighten quick-release axlenut 1 to the specified tight-ening torque.
Rear quick-release axlein swinging arm
100 Nm
Checking chain wearMake sure the ground is leveland firm and place the motor-cycle on its stand.
894
z Ma
inte
na
nc
e
Accelerated wear.If a component of the
sprocket with mounting parts isfound to be worn, the entire sethas to be replaced.
Pull the chain back at the rear-most point of the sprocket.The top of the teeth are stillbetween the chain links (a): thechain is OK.The chain is being pulled outover the top of the teeth (b):contact a specialist workshop,preferably an authorised BMWMotorrad dealer.
WheelsTyre recommendationFor each size of tyre BMWMotorrad tests certain makes,and approves those that itcertifies as roadworthy. If BMWMotorrad has not approved thewheels and tyres, it cannotassess their suitability or provideany guarantee of road safety.Use only wheels and tyres ap-proved by BMW Motorrad foryour type of motorcycle.You can obtain detailed informa-tion from your authorised BMWMotorrad dealer or on the Inter-net at www.bmw-motorrad.com.
Effect of wheel size onABSWheel size is very important as aparameter for the ABS. In partic-ular, the diameter and the widthof a motorcycle's wheels are pro-grammed into the control unit
and are fundamental to all cal-culations. Any change in theseinfluencing variables, caused forexample by a switch to wheelsother than those installed ex-works, can have serious effectson the performance of the con-trol systems.The sensor rings are essentialfor correct road-speed calcula-tion, and they too must matchthe motorcycle's control sys-tems and consequently cannotbe changed.If you decide that you would liketo fit non-standard wheels toyour motorcycle, it is very import-ant to consult a specialist work-shop beforehand, preferably anauthorised BMW Motorrad deal-er. In some cases, the data pro-grammed into the control unitscan be changed to suit the newwheel sizes.
895
z Ma
inte
na
nc
e
Removing front wheelMake sure the ground is leveland firm and place the motor-cycle on its stand.with BMW Motorrad ABS OE
Remove screw 1 and removethe speed sensor from itsbore.
Once the calipers havebeen removed, there is
a risk of the brake pads beingpressed together to the extentthat they cannot be slipped backover the brake disc on reas-sembly.Do not operate the handbrakelever when the brake calipershave been removed.
Remove screws 2 from theright brake caliper.
Force the brake pads 3 slightlyapart by rocking brake caliper 4back and forth against brakedisc 5.Mask off the parts of the wheelrim that could be scratched inthe process of removing thebrake calipers.Carefully pull the brake calipersback and out until clear of thebrake discs.
Place the motorcycle on a suit-able auxiliary stand.
896
z Ma
inte
na
nc
e
with centre stand OE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Raise front of motorcycle untilthe front wheel can turn freely.BMW Motorrad recommendsthe BMW Motorrad front-wheelstand for lifting the motorcycle.Install the front-wheel stand( 103).
Slacken right axle clampingscrews 1.
Remove axle screw 2.Slacken left axle clampingscrews 3.Push the axle in as far as it willgo.
Remove axle 4, while support-ing the wheel.Do not remove the grease fromthe axle.Roll the front wheel forward toremove.
897
z Ma
inte
na
nc
e
Remove spacing bushing 5from the left-hand side of thewheel hub.
Installing front wheel
Threaded fasteners nottightened to the specified
torque can work loose or theirthreads can suffer damage.Always have the security of thefasteners checked by a specialistworkshop, preferably an author-ised BMW Motorrad dealer.
Slip spacing bushing 5 ontothe left-hand side of the wheelhub.
The front wheel must beinstalled right way round to
rotate in the correct direction.Note the direction-of-rotation ar-rows on the tyre or the wheelrim.
Roll the front wheel into posi-tion between the forks, makingsure that the brake disc passesbetween the brake pads of thebrake caliper on the left.
Raise the front wheel and in-sert axle 4 until seated.Tighten right axle clampingscrews 1 to the specified tight-ening torque or install a suit-able tool to counter-hold forthe next step in the assemblyprocedure.
Clamp of quick-releaseaxle
Tightening sequence: 2xeach side, alternately
19 Nm
898
z Ma
inte
na
nc
e
Install axle screw 2 and tight-en to the specified tighteningtorque.
Quick-release axle, front,in axle holder
30 Nm
Tighten left axle clampingscrews 3 to the specifiedtightening torque.
Clamp of quick-releaseaxle
Tightening sequence: 2xeach side, alternately
Clamp of quick-releaseaxle
19 Nm
If fully tightened beforehand,slacken right axle clampingscrews 1 again.Remove the front-wheel stand.
with centre stand OE
Remove the auxiliary stand.
Ease the right brake caliperonto the brake disc.
Tighten screws 2 to the spe-cified tightening torque.
Brake caliper to fork leg
38 Nm
899
z Ma
inte
na
nc
e
with BMW Motorrad ABS OE
Insert the ABS sensor into itsbore and install screw 1.
Remove the adhesive tapefrom the wheel rim.Operate the brake severaltimes until the brake pads arebedded.
Firmly compress the front forksseveral times.
Tighten right axle clampingscrews 1 to the specified tight-ening torque.
Clamp of quick-releaseaxle
Tightening sequence: 2xeach side, alternately
19 Nm
Remove the rear wheelMake sure the ground is leveland firm and place the motor-cycle on its stand.
Remove screw 1 and removethe speed sensor from its bore.Make sure the ground is leveland firm and place the mo-torcycle on a suitable auxiliarystand.
with centre stand OE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
8100
z Ma
inte
na
nc
e
Remove axle nut 2.Slacken locknuts 3 on left andright by turning them counter-clockwise.Back off adjusting screws 4 onleft and right by turning themcounter-clockwise.Remove adjusting plate 5 andpush the axle in as far as it willgo.
Remove quick-release axle 6and remove adjusting plate 7.
Roll the rear wheel as far for-ward as possible and disen-gage chain 8 from the sprock-et.
Roll the rear wheel back until itis clear of the swinging arm.
The sprocket and thespacer sleeves on left
and right are loose fits in thewheel. Make sure that theseparts are not damaged or lost onremoval.
Installing rear wheel
Threaded fasteners nottightened to the specified
torque can work loose or theirthreads can suffer damage.Always have the security of thefasteners checked by a specialistworkshop, preferably an author-ised BMW Motorrad dealer.
Roll the rear wheel into theswinging arm, making sure thatthe brake disc passes betweenthe brake pads.
8101
z Ma
inte
na
nc
e
Roll the rear wheel as farforward as possible and loopchain 8 over the sprocket.
Seat left adjusting plate 7 inthe swinging arm and installquick-release axle 6 in the
brake caliper and the rearwheel.Make sure that the axle fits in-to the recess of the adjustingplate.
Install right adjusting plate 5.
Install nut 2, but do not tightenit at this point.
without centre standOE
Remove the auxiliary stand.
Insert the speed sensor intothe bore and install screw 1.
8102
z Ma
inte
na
nc
e
Adjusting chain sag ( 94).
Front-wheel standInstall the front-wheelstand
The BMW Motorrad frontwheel stand is not designed
to support the motorcyclewithout the assistance of anauxiliary stand. A motorcycleresting only on the front wheelstand and the rear wheel cantopple.Place the motorcycle on an aux-iliary stand before lifting the frontwheel with the BMW Motorradfront-wheel stand.
Place the motorcycle on a suit-able auxiliary stand.with centre stand OE
Make sure the ground is leveland firm and place the motor-cycle on its centre stand.
Use basic stand with tool num-ber (0 402 241) in combina-tion with front-wheel adapter(0 402 242).
Slacken adjusting screws 1.Push the two adapters 2 apartuntil the front forks fit betweenthem. Adjust the adapter studsto suit the front suspension.Use locating pins 3 to set thefront-wheel stand to the de-sired height.Centre the front-wheel standrelative to the front wheel andpush it against the front axle.
Align the two adapters 2 sothat the front forks are securelyseated.Tighten adjusting screws 1.
8103
z Ma
inte
na
nc
e
Apply uniform pressure to pushthe front-wheel stand downand raise the motorcycle.
with centre stand OE
If the motorcycle is raisedtoo far the centre stand will
lift clear of the ground and themotorcycle could topple to oneside.When raising the motorcycle,make sure that the centre standremains on the ground. If ne-cessary, adjust the height of thefront-wheel stand.
Make sure the motorcycle isstanding firmly.
BulbsGeneral instructionsA warning appears in the multi-function display if a bulb is de-fective.
A defective bulb placesyour safety at risk because
it is easier for other users tooversee the motorcycle.Replace defective bulbs assoon as possible; always carry acomplete set of spare bulbs ifpossible.
The bulb is pressurised andcan cause injury if dam-
aged.Wear protective goggles andgloves when changing bulbs.
The types of bulb fitted toyour motorcycle are listed
in the section entitled "Technicaldata".
Replacing low-beam andhigh-beam headlight bulb
Make sure the ground is leveland firm and place the motor-cycle on its stand.Switch off the ignition.
Remove cover 1 for the high-beam headlight or cover 2 forthe low-beam headlight.
8104
z Ma
inte
na
nc
e
Disconnect plug 3.
Disengage spring clips 4 fromthe fastenings and swing themaside.Remove bulb 5.
Replace the defective bulb.
Do not touch the glass ofnew bulbs with your fingers.
Use a clean, dry cloth to holdthe bulbs when handling them.Dirt deposits, in particular oil andgrease, interfere with heat radi-ation from the bulb. This leadsto overheating and shortens thebulb's operating life.
Bulb for high-beamheadlight
H7 / 12 V / 55 W
Bulbs for the low-beamheadlight
H7 / 12 V / 55 W
Install the bulb, making surethat alignment is correct at po-sition 6.Close and lock spring clips 4.
Connect plug 3.
8105
z Ma
inte
na
nc
e
Install cover 1 or cover 2, asapplicable.
Replacing parking-lightbulb
Make sure the ground is leveland firm and place the motor-cycle on its stand.Switch off the ignition.
Remove cover 2.
Pull parking-light bulb 3 out ofthe headlight housing.
Remove the bulb from the bulbholder.
Replace the defective bulb.
Do not touch the glass ofnew bulbs with your fingers.
Use a clean, dry cloth to holdthe bulbs when handling them.Dirt deposits, in particular oil andgrease, interfere with heat radi-ation from the bulb. This leadsto overheating and shortens thebulb's operating life.
8106
z Ma
inte
na
nc
e
Bulb for parking light
W5W / 12 V / 5 W
Push the bulb into the bulbsocket.
Insert parking-light bulb 3 intothe headlight housing.
Install cover 2.
Replacing brake light andrear light bulb
The LED rear light can be re-placed only as a complete unit.Consult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Replacing turn indicatorbulbs, front and rear
Make sure the ground is leveland firm and place the motor-cycle on its stand.Switch off the ignition.
Remove screw 1.
8107
z Ma
inte
na
nc
e
Pull the glass out of the reflect-or housing at the threaded-fastener side.
Turn bulb 2 counter-clockwiseand remove it from the bulbhousing.
Replace the defective bulb.
Do not touch the glass ofnew bulbs with your fingers.
Use a clean, dry cloth to holdthe bulbs when handling them.Dirt deposits, in particular oil andgrease, interfere with heat radi-ation from the bulb. This leadsto overheating and shortens thebulb's operating life.
Bulbs for flashing turnindicators, front
R10W / 12 V / 10 W
with white turn indicatorsOE
RY10W / 12 V / 10 W
with LED turn indicatorsOA
LED / 12 V
Bulbs for flashing turnindicators, rear
R10W / 12 V / 10 W
with white turn indicatorsOE
Bulbs for flashing turnindicators, rear
RY10W / 12 V / 10 W
with LED turn indicatorsOA
LED / 12 V
Turn bulb 2 clockwise to installit in the bulb housing.
8108
z Ma
inte
na
nc
e
Working from the inboard side,insert the glass into the bulbhousing and close the housing.
Install screw 1.
Replacing number-platelight bulbs
Make sure the ground is leveland firm and place the motor-cycle on its stand.Switch off the ignition.
Remove screw 1 from themudguard cover and removethe cover.
Pull bulb holder 2 out of thelight carrier.
Pull the bulb out of the bulbsocket.
8109
z Ma
inte
na
nc
e
Replace the defective bulb.
Do not touch the glass ofnew bulbs with your fingers.
Use a clean, dry cloth to holdthe bulbs when handling them.Dirt deposits, in particular oil andgrease, interfere with heat radi-ation from the bulb. This leadsto overheating and shortens thebulb's operating life.
Bulb for number-platelight
W5W / 12 V / 5 W
Insert the bulb into the bulbsocket.
Seat bulb holder 2 in the lightcarrier.
Hold the mudguard cover inposition and install screw 1.
Body panelsRemove the centre trimpanel
Remove the seat ( 48).
8110
z Ma
inte
na
nc
e
Remove screws 1 on left andright.
Remove four screws 2.Disconnect the plug from sock-et 3.Remove the centre trim panel.
Installing centre trimpanel
Connect the plug to the sock-et.
Manoeuvre the centre trimpanel into position. Make surethat all three tabs 4 on left andright engage the side panels.
Install four screws 2.
Install screws 1 on left andright.Installing seat ( 49).
8111
z Ma
inte
na
nc
e
Air filterRemoving air filter
Remove the centre trim panel( 110).
Remove screws 1.Remove air-filter cover 2.
Remove air filter 3.
Installing air filter
Install air filter 3.
Hold air-filter cover 2 in posi-tion.Install screws 1.Installing centre trim panel( 111).
Jump startingThe wires leading to thepower socket do not have
a load-capacity rating adequatefor jump-starting the engine. Ex-cessively high current can leadto a cable fire or damage to thevehicle electronics.Do not use the on-board socket
8112
z Ma
inte
na
nc
e
to jump-start the engine of themotorcycle.
A short-circuit can res-ult if the crocodile clips
of the jump leads are accident-ally brought into contact with themotorcycle.Use only jump leads fitted withfully insulated crocodile clips atboth ends.
Jump-starting with a donor-battery voltage higher than
12 V can damage the vehicleelectronics.Make sure that the battery of thedonor vehicle has a voltage ratingof 12 V.
Remove the centre trim panel( 110).When jump-starting the engine,do not disconnect the batteryfrom the on-board electricalsystem.
Begin by connecting one endof the red jump lead to thepositive terminal of the dis-charged battery and the otherend to the positive terminal ofthe donor battery (positive onthis vehicle: position 2).Then connect one end of theblack jump lead to the negat-ive terminal of the donor bat-tery and the other end to thenegative terminal of the dis-charged battery (negative onthis vehicle: position 1).
The spring-strut screw canbe used as an alternative to
the battery's negative terminal.
Run the engine of the donorvehicle during jump-starting.Start the engine of the vehiclewith the discharged batteryin the usual way; if the en-gine does not start, wait a fewminutes before repeating theattempt in order to protect thestarter motor and the donorbattery.Allow both engines to idle for afew minutes before disconnect-ing the jump leads.Disconnect the jump lead fromthe negative terminals first,then disconnect the secondlead from the positive termin-als.
Do not use proprietarystart-assist sprays or oth-
er products to start the engine.
8113
z Ma
inte
na
nc
e
Installing centre trim panel( 111).
BatteryMaintenance instructionsCorrect upkeep, recharging andstorage will prolong the life ofthe battery and are essential ifwarranty claims are to be con-sidered.Compliance with the points be-low is important in order to max-imise battery life:
Keep the surface of the batteryclean and dryDo not open the batteryDo not top up with waterBe sure to read and complywith the instructions for char-ging the battery on the follow-ing pagesDo not turn the battery upsidedown
If the battery is not discon-nected, the on-board elec-
tronics (e.g. clock, etc.) graduallydrain the battery. This can causethe battery to run flat. If this hap-pens, warranty claims will not beaccepted.If the motorcycle is to be out ofuse for more than four weeks,disconnect the battery or con-nect a suitable trickle charger tothe battery.
BMW Motorrad has de-veloped a float charger spe-
cially designed for compatibilitywith the electronics of your mo-torcycle. Using this charger, youcan keep the battery chargedduring long periods of disuse,without having to disconnect thebattery from the motorcycle'son-board systems. You can ob-tain additional information fromyour authorised BMW Motorraddealer.
Charge the battery whenconnected
Charging the connectedbattery directly at the bat-
tery terminals can damage thevehicle electronics.Always disconnect the batteryfrom the on-board circuits be-fore recharging it with a chargerconnected directly to the batteryposts.
Only chargers suitable forthis mode of charging can
be used to recharge the batteryvia the on-board socket. Unsuit-able chargers could cause dam-age to the motorcycle's on-boardelectrics.Use BMW chargers with thepart numbers 71 60 7 688 864(220 V) or, as applicable,71 60 7 688 865 (110 V). Ifyou are in doubt, disconnectthe battery from the on-board
8114
z Ma
inte
na
nc
e
systems and connect the chargerdirectly to the battery.
If you switch on the igni-tion and the multifunction
display and telltale lights fail tolight up, the battery is completelyflat. Attempting to charge a com-pletely flat battery via the on-board socket can cause damageto the motorcycle's electronics.If a battery has discharged to theextent that it is completely flat, ithas to be disconnected from theon-board circuits and chargedwith the charger connected dir-ectly to the battery posts.
Charge via the power sock-et, with the battery connectedto the motorcycle's on-boardelectrical system.
The motorcycle's on-boardelectronics know when the
battery is fully charged. Theon-board socket is switched offwhen this happens.
Comply with the operating in-structions of the charger.
If you are unable to chargethe battery through the on-
board socket, you may be usinga charger that is not compatiblewith your motorcycle's electron-ics. If this happens, disconnectthe battery from the on-boardsystems and connect the chargerdirectly to the battery.
Charging battery whendisconnected
Charge the battery using asuitable charger.Comply with the operating in-structions of the charger.Once the battery is fullycharged, disconnect thecharger's terminal clips fromthe battery terminals.
The battery has to be re-charged at regular intervals
in the course of a lengthy period
of disuse. See the instructionsfor caring for your battery. Al-ways fully recharge the batterybefore restoring it to use
Removing batteryMake sure the ground is leveland firm and place the motor-cycle on its stand.with anti-theft alarm OE
If applicable, switch off the anti-theft alarm.
Switch off the ignition.Remove the centre trim panel( 110).
8115
z Ma
inte
na
nc
e
Disconnection in the wrongsequence increases the risk
of short-circuits.Always proceed in the correctsequence.
Disconnect negative lead 1first.Then disconnect positivelead 2.Remove screws 3 on left andright and remove the batteryholder.Lift the battery up and out;work it slightly back and forthif it is difficult to remove.
Installing battery
If the battery was discon-nected from the motorcycle
for a prolonged period of timeit will be necessary to enter thecurrent date in the instrumentpanel, in order to ensure that theservice-due indicator functionscorrectly.If you want to have the date setconsult a specialist workshop,preferably an authorised BMWMotorrad dealer.
Switch off the ignition.Insert the battery into the bat-tery compartment, with thepositive terminal on the rightin the direction of travel.
Place the battery holder in po-sition, making sure that theleads are correctly routed atposition 4.Install screws 3 on left andright.
Connection in the wrongsequence increases the risk
of short-circuits.Always proceed in the correctsequence.
Connect positive lead 2 to thebattery's positive terminal.Connect negative lead 1 to thebattery's negative terminal.
8116
z Ma
inte
na
nc
e
Installing centre trim panel( 111).Setting clock ( 35).
8117
z Ma
inte
na
nc
e
8118
z Ma
inte
na
nc
e
Care
Care
Care products . . . . . . . . . . . . . . . . . . . . . 120
Washing motorcycle . . . . . . . . . . . . . . . 120
Cleaning easily damaged compon-ents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Paint care . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Protective wax coating . . . . . . . . . . . . . 122
Laying up motorcycle . . . . . . . . . . . . . . 122
Restoring motorcycle to use . . . . . . . 122
9119
z Ca
re
Care productsBMW Motorrad recommendsthat you use the cleaning andcare products you can obtainfrom your authorised BMWMotorrad dealer. The substancesin BMW Care Products havebeen tested in laboratories and inpractice; they provide optimisedcare and protection for thematerials used in your vehicle.
The use of unsuitablecleaning and care products
can damage vehicle components.Do not use solvents such as cel-lulose thinners, cold cleaners,fuel or the like, and do not usecleaning products that containalcohol.
Washing motorcycleBMW Motorrad recommendsthat you use BMW insect re-mover to soften and wash offinsects and stubborn dirt on
painted parts prior to washingthe motorcycle.To prevent stains, do not washthe motorcycle immediately afterit has been exposed to strongsunlight and do not wash it in thesun.Make sure that the motorcycleis washed frequently, especiallyduring the winter months.To remove road salt, clean themotorcycle with cold water im-mediately after every trip.
After the motorcycle hasbeen washed, ridden
through water or ridden inthe rain, the brake discs andpads might be wet and thebrakes might not take effectimmediately.Apply the brakes in good timeuntil the brake discs and brakepads have dried out.
Warm water intensifies theeffect of salt.
Use only cold water to wash offroad salt.
The high pressure of steamcleaners can damage seals,
the hydraulic brake system, theelectrical system, and the seat.Do not use a steam jet or high-pressure cleaning equipment.
Cleaning easilydamaged componentsPlasticsClean plastic parts with waterand BMW plastic care emulsion.This includes in particular:
Windscreen and slipstream de-flectorsHeadlight lens made of plasticGlass of the instrument panelBlack, unpainted parts
9120
z Ca
re
If plastic parts are cleanedusing unsuitable cleaning
agents, the surfaces can be dam-aged.Do not use cleaning agents thatcontain alcohol, solvents or ab-rasives to clean plastic parts.Even fly-remover pads or clean-ing pads with hard surfaces canproduce scratches.
Soften stubborn dirt andinsects by covering the af-
fected areas with a wet cloth.
ChromeUse plenty of water and BMWshampoo to clean chrome, par-ticularly if it has been exposed toroad salt. Use chrome polish foradditional treatment.
RadiatorClean the radiator regularly toprevent overheating of the en-gine due to inadequate cooling.For example, use a garden hosewith low water pressure.
Cooling fins can be benteasily.
Take care not to bend the finswhen cleaning the radiator.
RubberTreat rubber components withwater or BMW rubber-careproducts.
Using silicone sprays forthe care of rubber seals can
cause damage.Do not use silicone sprays orother care products that containsilicon.
Paint careWashing the motorcycle regularlywill help counteract the long-termeffects of substances that dam-age the paint, especially if yourmotorcycle is ridden in areaswith high air pollution or naturalsources of dirt, for example treeresin or pollen.Remove particularly aggressivesubstances immediately, how-ever, as otherwise the paint canbe affected or become discol-oured. Substances of this natureinclude spilt fuel, oil, grease,brake fluid and bird droppings.We recommend BMW vehiclepolish or BMW paint cleaner forthis purpose.Marks on the paintwork are par-ticularly easy to see after themotorcycle has been washed.Remove stains of this kind im-mediately, using cleaning-gradebenzene or petroleum spirit on aclean cloth or ball of cotton wool.
9121
z Ca
re
BMW Motorrad recommendsBMW tar remover for removingspecks of tar. Remember to waxthe parts treated in this way.
Protective wax coatingBMW Motorrad recommendsapplying only BMW car wax orproducts containing carnaubawax or synthetic wax.It is time to rewax the paint-work when water "puddles" onthe surface, instead of formingbeads.
Laying up motorcycleClean the motorcycle.Removing battery ( 115).Spray the brake and clutchlever pivots, the side standpivots and the centre standpivots (if the motorcycle is fit-ted with a centre stand) with asuitable lubricant.
Coat bright metal and chrome-plated parts with an acid-freegrease (e.g. Vaseline).Stand the motorcycle in a dryroom in such a way that thereis no load on either wheel.
Before laying the vehicleup out of use, have the en-
gine oil and the oil filter elementchanged by a specialist work-shop, preferably an authorisedBMW Motorrad dealer. Com-bine work for laying up/restoringto use with a BMW service orinspection.
Restoring motorcycleto use
Remove the protective waxcoating.Clean the motorcycle.Install a charged battery.Before starting: work throughthe checklist.
9122
z Ca
re
Technical data
Technical data
troubleshooting chart . . . . . . . . . . . . . . 124
Threaded fasteners . . . . . . . . . . . . . . . . 125
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Transmission . . . . . . . . . . . . . . . . . . . . . . 130
Rear-wheel drive . . . . . . . . . . . . . . . . . . . 131
Running gear . . . . . . . . . . . . . . . . . . . . . . 131
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Wheels and tyres . . . . . . . . . . . . . . . . . . 132
Electrics . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 136
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Riding specifications . . . . . . . . . . . . . . . 13710123
z Te
ch
nic
al d
ata
troubleshooting chartEngine does not start at all or is difficult to start.Possible cause Rectification
Emergency off switch (kill switch) Kill switch in operating position (run).
Side stand Retract the side stand ( 54).
Gear engaged and clutch not disengaged. Select neutral or pull the clutch lever ( 54).
Clutch pulled before ignition was switched on Switch on the ignition, then pull the clutch lever.
No fuel in tank Refuelling ( 60).
Battery flat Charge the battery when connected ( 114).
10124
z Te
ch
nic
al d
ata
Threaded fastenersFront wheel Value Valid
Brake caliper to fork leg
ASA screw with washer, M10 x 40 38 Nm
Clamp of quick-release axle
M8 x 25 2x each side, alternately
19 Nm
Quick-release axle, front, in axleholder
M14 x 1.5 30 Nm
Rear wheel Value Valid
Locknut of the final-drive chaintensioning screw
M8 19 Nm
Rear quick-release axle inswinging arm
M16 x 1.5 100 Nm
10125
z Te
ch
nic
al d
ata
Mirror arm Value Valid
Locknut (mirror) to clamp ad-apter
M14 x 1 20 Nm
Clamp adapter (mirror) toclamping block
M10 30 Nm
10126
z Te
ch
nic
al d
ata
Engine
Engine design Two-cylinder four-stroke, DOHC with chain-and-sprocket drive, 4 valves operated by cam follow-ers, balancing conrod, liquid-cooled cylinders andheads, integral water pump, 6-speed gearbox anddry sump lubrication
Displacement 798 cm3
Cylinder bore 82 mm
Piston stroke 75.6 mm
Compression ratio 12 : 1
Nominal output 63 kW, at engine speed: 7500 min-1
with regular unleaded (RON 91) OE 61 kW, at engine speed: 7500 min-1
Torque 83 Nm, at engine speed: 5750 min-1
with regular unleaded (RON 91) OE 81 Nm, at engine speed: 5750 min-1
Maximum engine speed max 9000 min-1
Idle speed 1250+50 min-1
10127
z Te
ch
nic
al d
ata
Fuel
Recommended fuel grade Super unleaded95 ROZ/RON89 AKI
with regular unleaded (RON 91) OE Regular unleaded (slight power- andconsumption-related restrictions)91 ROZ/RON87 AKI
Usable fuel capacity approx. 16 l
Reserve fuel approx. 4 l
BMW recommends BP fuels
10128
z Te
ch
nic
al d
ata
Engine oil
Engine oil, capacity 2.9 l, with filter change
products recommended by BMW Motorrad and generally admissible viscosity classes
Castrol GPS SAE 10W-40, API SG / JASO MA -20 °C
SAE 10W-40, API SF / SG / SH -20 °C, Operation in winter
SAE 15W-40, API SF / SG / SH -10 °C
Oil additives BMW Motorrad recommends not using oil addit-ives, because they can have a detrimental effecton clutch operation. Please do not hesitate tocontact your authorised BMW Motorrad dealerif you have any questions relating the choice of asuitable engine oil for your motorcycle.
BMW recommends
10129
z Te
ch
nic
al d
ata
Clutch
clutch type Multiplate clutch running in oil bath
Transmission
gearbox type Claw-shift 6-speed gearbox, integrated into en-gine block
Gearbox transmission ratios 1.943 (35/68 teeth), Primary transmission ratio1:2.462 (13/32 teeth), 1st gear1:1.750 (16/28 teeth), 2nd gear1:1.381 (21/29 teeth), 3rd gear1:1.174 (23/27 teeth), 4th gear1:1.042 (24/25 teeth), 5th gear1:0.960 (25/24 teeth), 6th gear
10130
z Te
ch
nic
al d
ata
Rear-wheel drive
Type of final drive chain drive
Type of rear suspension Two-arm cast-aluminium swinging arm
Number of teeth, rear-wheel drive (Pinion /sprocket)
16 / 42
Running gear
Front wheel
Type of front suspension Upside-down telescopic fork
Spring travel, front 230 mm, At wheel
Rear wheel
Type of rear suspension Two-arm cast-aluminium swinging arm
Type of rear suspension Direct-pivot central spring strut with steplesslyadjustable rebound-stage damping
Spring travel at rear wheel 215 mm, At wheel
10131
z Te
ch
nic
al d
ata
Brakes
Front wheel
Type of front brake Hydraulically operated twin disc brake with 2-pis-ton floating calipers and floating brake discs
Brake-pad material, front Sintered metal
Rear wheel
Type of rear brake Hydraulically operated disc brake with 1-pistonfloating caliper and fixed disc
Brake-pad material, rear Organic material
Wheels and tyres
Recommended tyre sets You can obtain an up-to-date list of approvedtyres from your authorised BMW Motorrad dealeror on the Internet at "www.bmw-motorrad.com".
Front wheel
front wheel type Spoked wheel, MT H2
front wheel rim size 2.15" x 21"
Tyre designation, front 90 / 90 - 21
10132
z Te
ch
nic
al d
ata
Rear wheel
rear-wheel type Spoked wheel, MT H2
rear wheel rim size 4.25" x 17"
Tyre designation, rear 150 / 70 - 17
Tyre pressure
Tyre pressure, front 2.2 bar, one-up, at tyre temperature: 20 °C2.4 bar, two-up and/or with luggage, at tyre tem-perature: 20 °C
Tyre pressure, rear 2.4 bar, one-up, at tyre temperature: 20 °C2.8 bar, two-up and/or with luggage, at tyre tem-perature: 20 °C
10133
z Te
ch
nic
al d
ata
Electrics
Electrical rating of on-board socket 5 A
Fuses Electronic fuses protect all the circuits. If an elec-tronic fuse trips and de-energises a circuit, thecircuit is active as soon as the ignition is switchedon after the fault has been rectified.
Battery
battery type AGM (Absorbent Glass Mat) battery
battery rated voltage 12 V
battery rated capacity 14 Ah
Spark plugs
Spark plugs, manufacturer and designation NGK DCPR 8 E
Electrode gap of spark plug 0.8...0.9 mm, When new
Lighting
Bulb for high-beam headlight H7 / 12 V / 55 W
Bulbs for the low-beam headlight H7 / 12 V / 55 W
Bulb for parking light W5W / 12 V / 5 W
Bulb for tail light/brake light LED / 12 V
Bulb for number-plate light W5W / 12 V / 5 W
Bulbs for flashing turn indicators, front R10W / 12 V / 10 W
10134
z Te
ch
nic
al d
ata
with white turn indicatorsOE RY10W / 12 V / 10 W
with LED turn indicatorsOA LED / 12 V
Bulbs for flashing turn indicators, rear R10W / 12 V / 10 W
with white turn indicatorsOE RY10W / 12 V / 10 W
with LED turn indicatorsOA LED / 12 V
Frame
Frame type tubular spaceframe
type plate location Steering head, front top
VIN location Steering head, right
10135
z Te
ch
nic
al d
ata
Dimensions
Length of motorcycle 2320 mm, across front wheel to number-platecarrier
Height of motorcycle 1350 mm, without rider at DIN unladen weight
Width of motorcycle 870 mm, across mirrors without mirrors
Front-seat height 880 mm, Without rider at unladen weight
with dual seat, low OE 850 mm, Without rider at unladen weight
rider's inside-leg arc, heel to heel 1940 mm
with dual seat, low OE 1900 mm, Without rider at unladen weight
Weights
Unladen weight 207 kg, DIN unladen weight, ready for road, 90 %load of fuel, without optional extras
Permissible gross weight 443 kg
Maximum payload 236 kg
10136
z Te
ch
nic
al d
ata
Riding specifications
Top speed >200 km/h10137
z Te
ch
nic
al d
ata
10138
z Te
ch
nic
al d
ata
Service
Service
BMW Motorrad service . . . . . . . . . . . . 140
BMW Motorrad service quality . . . . . 140
BMW Motorrad mobility services -roadside assistance . . . . . . . . . . . . . . . . 140
BMW Motorrad servicenetwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Maintenance work . . . . . . . . . . . . . . . . . 141
Confirmation of maintenancework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Confirmation of service . . . . . . . . . . . . 147
11139
z Se
rvic
e
BMW Motorrad serviceAdvanced technology requiresspecially adapted methods ofmaintenance and repair.
If maintenance and re-pair work is performed in-
expertly, it could result in con-sequential damage and thus con-stitute a safety risk.BMW Motorrad recommends youto have all the associated workon your motorcycle carried outby a specialist workshop, prefer-ably an authorised BMW Motor-rad dealer.
Your authorised BMW Motorraddealer can provide information onBMW services and the work un-dertaken as part of each service.Have all maintenance and repairwork carried out confirmed in the"Service" chapter in this manual.Authorised BMW Motorrad deal-ers are supplied with the latesttechnical information and have
the necessary technical know-how. BMW Motorrad recom-mends that you contact your au-thorised BMW Motorrad dealerif you have questions regardingyour motorcycle.
BMW Motorrad servicequalityAlong with its reputation for en-gineering quality and high reliab-ility, BMW Motorrad is a bywordfor excellent quality of service.To ensure that your BMW is al-ways in optimum condition, BMWMotorrad recommends that youhave the maintenance work re-quired for your motorcycle car-ried out regularly, preferably byyour authorised BMW Motor-rad dealer. For generous treat-ment of claims submitted afterthe warranty period has expired,evidence of regular maintenanceis essential.
Certain signs of wear, moreover,may otherwise not be noticeduntil it is too late to put themright at moderate cost. Your au-thorised BMW Motorrad dealer'smechanics know every detail ofyour motorcycle and can take re-medial action if necessary beforeminor faults develop into seriousproblems. By having the neces-sary repairs done properly andin good time, you save time andmoney in the long run.
BMW Motorrad mobilityservices - roadsideassistanceIn the event of a breakdown, theBMW Motorrad mobility servicesavailable for each new BMW mo-torcycle enable you to access anextensive range of services suchas breakdown assistance, motor-cycle transportation etc. (detailscan differ from country to coun-try). In the event of a breakdown,
11140
z Se
rvic
e
contact the Mobile Service or-ganisation of BMW Motorrad.The specialists will provide thenecessary advice and assistance.You will find important country-specific contact addresses andthe after-sales service organisa-tion phone numbers in the "Ser-vice Kontakt / Service Contact"brochures, along with informa-tion on Mobile Service and thedealership network.
BMW Motorrad servicenetworkBMW Motorrad has an extens-ive after-sales service network inplace to look after you and yourmotorcycle in more than 100countries. In Germany alone, youhave the best possible accessto approximately 200 authorisedBMW Motorrad dealers.All information concerning the in-ternational dealership networkcan be found in the brochure
"Service Contact Europe" or"Service Contact Africa, Amer-ica, Asia, Australia, Oceania".
Maintenance workBMW Pre-delivery CheckYour authorised BMW Motorraddealer conducts the BMW pre-delivery check before handingover the motorcycle to you.
BMW Running-in CheckThe BMW running-in check hasto be performed when the mo-torcycle has covered between500 km and 1500 km.
BMW ServiceThe BMW Service is carried outonce a year; the extent of servi-cing can vary, depending on theage of the motorcycle and thedistance it has covered. Your au-thorised BMW Motorrad dealerconfirms that the service workhas been carried out and enters
the date when the next servicewill be due.Riders who cover long distancesin a year might have to bring intheir motorcycles for service be-fore the next scheduled date. Itis to allow for these cases thata maximum odometer reading isentered as well in the confirma-tion of service. Servicing has tobe brought forward if this odo-meter reading is reached beforethe next scheduled date for theservice.
The service-due indicator in themultifunction display reminds youabout one month or 1000 km inadvance when the time for a ser-vice is approaching, on the basisof the programmed values.
11141
z Se
rvic
e
Confirmation of maintenance work
BMW Pre-deliveryCheckCompleted
on
Stamp, signature
BMW Running-inCheckCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11142
z Se
rvic
e
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11143
z Se
rvic
e
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11144
z Se
rvic
e
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11145
z Se
rvic
e
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
BMW ServiceCompleted
on
Odometer reading
Next serviceat the latest
onor, if logged beforehand,
Odometer reading
Stamp, signature
11146
z Se
rvic
e
Confirmation of serviceThe table is intended as a record of maintenance and repair work, the installation of optional accessoriesand, if appropriate, special campaign (recall) work.
Item Odometerreading
Date
11147
z Se
rvic
e
Item Odometerreading
Date11148
z Se
rvic
e
AAbbreviations and symbols, 6ABS
Control, 16Engineering details, 66Operation, 42Self-diagnosis, 56Warnings, 32
AccessoriesGeneral instructions, 70
Air filterInstallation, 112Position on the motorcycle, 15Removal, 112
Aluminium casesOperation, 77
Aluminium topcaseOperation, 79
Anti-theft alarmTelltale light, 18Warnings, 31
BBattery
Charging battery whenconnected, 114Charging battery whendisconnected, 115Installation, 116Maintenance instructions, 114Position on the motorcycle, 15Removal, 115Technical data, 134
Brake fluidChecking fluid level, front, 89Checking fluid level, rear, 90Reservoir, front, 13Reservoir, rear, 13
Brake padsChecking front, 87Checking rear, 88Running in, 57
BrakesAdjusting handlebar lever, 43Checking operation, 86Safety instructions, 59Technical data, 132
BulbsGeneral instructions, 104Replacing high-beam headlightbulb, 104Replacing low-beam headlightbulb, 104Replacing number-plate lightbulbs, 109Replacing side-light bulb, 106Replacing the brake light andrear light bulbs, 107Replacing turn indicatorbulbs, 107Technical data, 134Warning for bulb failure, 30
CCase
Operation, 71Chain
Adjusting sag, 94Checking sag, 93Checking wear, 94Lubricating, 93
Checklist, 54
12149
z Ind
ex
ClockAdjusting, 35Control, 18
ClutchAdjusting handlebar lever, 43Adjusting play, 92Checking operation, 91Checking play, 92Technical data, 130
Confirmation of maintenancework, 142
CoolantChecking fill level, 91Fill-level indicator, 13Topping up, 91Warning forovertemperature, 29
Currency, 7
DDamping
Adjuster, 13Adjusting, 46
DimensionsTechnical data, 136
EElectrics
Technical data, 134Emergency off switch (kill
switch), 17Operation, 41
EngineControl, 17Starting, 54Technical data, 127Warning for engineelectronics, 30
Engine oilChecking fill level, 85Filler neck, 11Oil dipstick, 11Technical data, 129Topping up, 86Warning for engine oilpressure, 30
Equipment, 7
FFirst-aid kit
Stowage, 14
FrameTechnical data, 135
Front-wheel standInstalling, 103
FuelFiller neck, 13Fill-level indicator, 23Refuelling, 60Technical data, 128Warning for fuel down toreserve, 29
Fuses, 134
GGeneral views
Instrument panel, 18Left handlebar fitting, 16Left side of motorcycle, 11Multifunction display, 22Right handlebar fitting, 17Right side of motorcycle, 13Underneath the seat, 14Underneath the trim panel, 15Warning and telltale lights, 24
12150
z Ind
ex
Grip heatingControl, 17Operation, 41
HHandlebar fittings
General view, left side, 16General view, right side, 17
Hazard warning flashersControl, 16, 17Operation, 40
HeadlightAdjusting headlight beamthrow, 48Beam throw, 47Driving on right/driving onleft, 47
Helmet holderHelmet, securing, 49Position on the motorcycle, 14
Horn, 16
IIgnition
Switching off, 34Switching on, 34
ImmobiliserReserve key, 35Warning, 29
Instrument panelAmbient-light brightnesssensor, 18Overview, 18
JJump starting, 112
KKeys, 34
LLights
Control, 16Headlight flasher, operating, 39High-beam headlight,operating, 39Low-beam headlight, 39Parking lights, operating, 39Side light, 39
LuggageInstructions for loading, 52lashing, 71
MMaintenance
General instructions, 84Maintenance intervals, 141Mirrors
Adjusting, 44Mobility services, 140Motorcycle
care, 119Cleaning, 119Laying up, 122Parking, 60Restoring to use, 122
Multifunction display, 18Overview, 22Select the readings, 36
OOdometer and tripmeters
Control, 18Off-roading, 58On-board computer
Control, 16Warnings, 31
12151
z Ind
ex
PParking, 60Power socket
Notes on use, 70Position on the motorcycle, 11
Pre-ride check, 55
RRear-wheel drive
Technical data, 131Redline warning
Indicator, 18Switching on, 57
Refuelling, 60Reserve volume
Warning, 29Rev. counter, 18Rider's Manual
Position on the motorcycle, 14Running gear
Technical data, 131Running in, 56
SSafety instructions
for brake, 59for riding, 52
SeatInstallation, 48Lock, 11Removal, 48
Service, 140Service-due indicator, 25Spark plugs
Technical data, 134Speedometer, 18Spring preload
Adjuster, 13Adjusting, 45Tools, 14
Starting, 54Control, 17
Steering lock, 34Stopwatch
Operation, 37
TTechnical data
Battery, 134Brakes, 132Bulbs, 134Clutch, 130Dimensions, 136Electrics, 134Engine, 127Engine oil, 129Frame, 135Fuel, 128Rear-wheel drive, 131Running gear, 131Spark plugs, 134Standards, 7Transmission, 130Weights, 136Wheels and tyres, 132
Telltale lights, 18Overview, 24
ToolkitContents, 84Position on the motorcycle, 14
12152
z Ind
ex
topcaseOperation, 74
Torques, 125Transmission
Technical data, 130Transportation
Lashing, 62Trim panels
Installing centre trim panel, 111Removing centre trimpanel, 110
troubleshooting chart, 124Turn indicators
Control, left, 16Control, right, 17Operation, 40
Type platePosition on the motorcycle, 13
TyresChecking inflation pressure, 46Checking tread depth, 93Pressures, 133Recommendation, 95Running in, 57
Table of tyre pressures, 14Technical data, 132
VVehicle identification number
Position on the motorcycle, 13
WWarning lights, 18
Overview, 24Warnings
Mode of presentation, 26With ABS, 32With anti-theft alarm, 31With on-board computer, 31
Warnings, overview, 27Weights
Payload table, 14Technical data, 136
WheelsChange of size, 95Checking rims, 92Checking spokes, 92Installing front wheel, 98Installing rear wheel, 101Remove the rear wheel, 100
Removing front wheel, 96Technical data, 132 12
153
z Ind
ex