1
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
Programme
Degree of Mechanical Engineering
Award
Bachelor in Mechanical Engineering With Honours
Programme duration Minimum Maximum 8 semesters 12 semesters Admission Requirement The apllicants must fulfill the minimum requirement for this programme, as follows: 1. Sijil Tinggi Persekolahan Malaysia (STPM) holder
Applicants must fullfill the university general requirement and the programme special requirement: a) University General Requirement
Passed Sijil Pelajaran Malaysia (SPM)/equivalent with a credit in Bahasa Melayu/Bahasa Malaysia or a credit in Bahasa Melayu/Bahasa Malaysia July Paper;
and
Passed Sijil Tinggi Persekolahan Malaysia (STPM) with a CGPA of at least 2.00 . Obtained at least Grade C (CGPA 2.00) in these following subjects:
• General Paper
• 2 other subjects and
Obtained at least Band 1 in Malaysian University English Test (MUET) however the candidate is required to achieve at least Band 2 upon graduation
b) Programme Special Requirement
Obtained at least Grade C (CGPA 2.00) at STPM level in these following subjects :
• Mathematics T / Further Mathematics T; • Physics; and • Chemistry
and Passed the SPM English Language.
and
Should have no impaired vision and any physical disabilities that interfere with practical works.
Note: Students must obtain at least Band 2 MUET before graduation.
2
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
2. Candidates with Diploma / Diploma Equivalent
Applicants must fullfill the university general requirement and the programme special requirement a) University General Requirement
Passed Sijil Pelajaran Malaysia (SPM)/equivalent with a credit in Bahasa Melayu/Bahasa Malaysia or a credit in Bahasa Melayu/Bahasa Malaysia July Paper;
and
Obtained a diploma or other recognised qualifications in the relevant fields recognized by the Malaysian Government and certified by IPTA’s Senate.
and
Obtained at least Band 1 in Malaysian University English Test (MUET).
b) Programme Special Requirement
Obtained a diploma or other recognised qualifications in the relevant fields of engineering and technology with CGPA of 2.70; or 2 years working experience in the relevant fields for candidates with CGPA of 2.50
and
Obtained at least Band 1 for MUET however the candidate is required to get Band 2 upon graduation.
and Passed the SPM English Language
and
Should have no impaired vision and any physical disabilities that interfere with the practical work
Note: Diploma holders are eligible for credit exemption based on the grades of the subjects and fields taken. 3. Candidates from MOE Matriculation
Applicants must fullfill the university general requirement and the programme special requirement:
a) University General Requirement Passed Sijil Pelajaran Malaysia (SPM)/equivalent with a credit in Bahasa Melayu/Bahasa Malaysia or a credit in Bahasa Melayu/Bahasa Malaysia July Paper;
and
Passed in MOE Matriculation with a CGPA of at least 2.00;
and
3
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
Obtained at least Band 1 in Malaysian University English Test (MUET) however the candidate is required to achieve at least Band 2 upon graduation
b) Programme Special Requirement
Obtained at least Grade C (2.00) at Matriculation/ Foundation level in these following subjects:
• Mathematics / Engineering Mathematics ; • Physics / Engineering Physics; and • Chemistry / Engineering Chemistry
and
Obtained at least a pass in SPM English Language.
and
Should have no impaired vision and any physical disabilities that interfere with practical works. Note: Students must obtain at least Band 2 MUET before graduation. PROGRAMME EDUCATIONAL OBJECTIVES (PEO) The Faculty has underlined the following long-term objectives for all its programs to produce:
1. Graduates with the necessary professional practice and acumen necessary for the success in the engineering profession and/or graduate level study
2. Graduates with the ability to practice mechanical engineering in the global marketplace and develop specialised interest in related areas.
3. Graduates with the competence to formulate and solve engineering problems through analytical and innovative approaches.
4. Graduates with the ability to communicate effectively, to lead and to appreciate entrepreneurship while being aware of environmental and ethical responsibilities.
5. Graduates with strong commitment for self learning and continuous professional development
PROGRAMME LEARNING OUTCOMES (PLO) Upon completion of the course the student should be able to:
1. Apply knowledge of mathematics, science, and engineering 2. Acquire in-depth knowledge and technical competency in mechanical systems and its related discipline. 3. Communicate effectively using a variety of appropriate mediums. 4. Adapt and use techniques, skills, and appropriate engineering tools necessary for engineering research
and practices 5. Identify problems, create solutions, innovate and improve current practices in mechanical systems and its
components. 6. Appreciate aesthetic values through applications of technical judgement and creativity. 7. Demonstrate professional and ethical responsibility with commitment to the community for the benefit of
mankind. 8. Work effectively in groups in ways that contribute to effective working relationships and the achievement
4
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
of goals both as a leader as well as effective team players
9. Comprehend global perspective on social culture and environmental responsibilities of a professional engineer in sustaining development
10. Recognise the need to engage in life-long learning 11. Recognise the importance of entrepreneurship in mechanical engineering and its related discipline.
Programme Structure
Code Subject Credit Lecture Tutorial Practical TCH UM* 1312 Foreign Language 2 2 1 0 3
UMA 1162 Islam Civilisation and Asian Civilisation
2 2 0 0 2
UMA 1182/ UMA 1142
Islamic Studies/Moral Studies 2 2 0 0 2
UMS 1122/ UMN 1312
Ethnic Relation/Malay Language 2 2 0 0 2
UMB 1042 Technical Writing 2 2 1 0 3 UMB 1052 Effective Communication 2 1 0 3 4 UMC 1022 Creativity and Innovation 2 2 1 0 3
UMS 1113/ UMS 1143
Nationhood and Current Development/Malaysia Studies and Culture
3 3 0 0 3
UQ* 1**1 Co- Curriculum I 1 0 0 3 3 UQ* 1**1 Co- Curriculum II 1 0 0 3 3
UMB 1011 English For Academic Purposes 1 0 0 0 1 BSM 1913 Engineering Mathematics I 3 3 1 0 4 BSM 1923 Engineering Mathematics II 3 3 1 0 4 BSM 2913 Engineering Mathematics III 3 3 1 0 4 BSM 2922 Engineering Statistics 2 2 1 0 3 BSM 3913 Engineering Mathematics IV 3 3 1 0 4
BDA 3053 Engineering Economics and Entrepreneurship
3 3 1 0 4
BDA 4042 Management and Professional Ethics
2 2 1 0 3
BDA 4052 Engineers and Society 2 2 1 0 3 BTI 1022 Computer Programming 2 1 0 3 4 BDA 1012 Engineering Drawings 2 1 0 3 4 BDA 1023 Static 3 3 1 0 4 BDA 1032 Material Sciences 2 2 1 0 3 BDA 1042 Mechanics of Solid I 2 2 1 0 3 BDA 1052 Fluid Mechanics I 2 2 1 0 3
BEE 1803 Electrical and Electronic Technology
3 3 1 0 4
BDA 1701 Engineering Lab I 1 0 0 3 3 BDA 1801 Mechanical Engineering Practice I 1 0 0 3 3 BDA 1811 Mechanical Engineering Practices II 1 0 0 3 3 BDA 2013 Dynamics 3 3 1 0 4 BDA 2022 Thermodynamics I 2 2 1 0 3
5
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
BDA 2033 Mechanics of Machine 3 3 1 0 4 BDA 2042 Engineering Materials Selection 2 2 1 0 3 BDA 2052 CAD and Modelling 2 1 0 3 4 BDA 2701 Engineering Lab II 1 0 0 3 3 BDA 2711 Engineering Lab III 1 0 0 3 3
BDA 2721 Engineering Lab IV 1 0 0 3 3
BDA 2801 Mechanical Engineering Practices III
1 0 0 3 3
BDA 2811 Mechanical Engineering Practices IV
1 0 0 3 3
BDA 3023 Fluid Mechanics II 3 3 1 0 4 BDA 3033 Solid Mechanics II 3 3 1 0 4 BDA 3043 Thermodynamics II 3 3 1 0 4 BDA 3052 Manufacturing Technology 2 2 1 0 3 BDA 3063 Heat Transfer 3 2 0 3 5 BDA 3073 Control Engineering 3 3 1 0 4 BDA 3083 Mechanical Design I 3 2 0 3 5 BDA 3701 Engineering Lab V 1 0 0 3 3 BDA 3711 Engineering Lab VI 1 0 0 3 3 BDA 4012 Industrial Engineering 2 2 1 0 3 BDA 4023 Mechanical Engineering Design II 3 2 0 3 5 BDA 4033 Finite Element Method 3 2 0 3 5 BDC 4013 Noise and Vibration 3 2 0 3 5 BDA 4804 Industrial Training(3 Months) 4 - - - - BDA 4902 Bachelor Project I 2 - - 6 6 BDA 4904 Bachelor Project II 4 - - 12 12 BD* 4**3 Elective I 3 2 0 3 5 BD* 4**3 Elective II 3 2 0 3 5 BD* 4**3 Elective III 3 2 0 3 5
TOTAL 129 94 26 90 211
Code Subject Credit Lecture Tutorial Practical TCH Manufacturing Elective
BDD 4013 Design for Manufacturing and Assembly
3 2 0 3 5
BDD 4023 Computer Aided Design and Manufacturing
3 2 0 3 5
BDD 4033 Manufacturing and Rapid Development
3 2 0 3 5
BDD 4043 Rapid Manufacturing 3 2 0 3 5
BDD 4053 Concurrent and Reverse Engineering
3 2 0 3 5
BDD 4063 Metal Casting Process 3 2 0 3 5 BDD 4073 Advanced Machining 3 2 0 3 5 BDD 4083 Manufacturing Control Technology 3 2 0 3 5
6
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
Material Elective
BDB 4013 Thermodynamics of Materials 3 2 0 3 5 BDB 4023 Material Testing 3 2 0 3 5 BDB 4033 Mechanical Metallurgy 3 2 0 3 5 BDB 4043 Corrosion and Prevention 3 2 0 3 5 BDB 4053 Applied Metallurgy 3 2 0 3 5 BDB 4063 Polymer and Ceramics 3 2 0 3 5 BDB 4073 Composite 3 2 0 3 5 BDB 4083 Advanced Materials 3 2 0 3 5
Gneral Mechanical Elective BDC 4023 Control System Design 3 2 0 3 5 BDC 4033 Stress Analysis 3 2 0 3 5 BDC 4043 Kinematics of Mechanism 3 2 0 3 5 BDC 4053 Fatigue and Fracture Mechanics 3 2 0 3 5 BDC 4063 Tribology 3 2 0 3 5 BDC 4073 Robotics 3 2 0 3 5 BDC 4083 Modelling and Simulation 3 2 0 3 5
Plant Elective
BDE 4013 Refrigeration and Air-conditioning System
3 2 0 3 5
BDE 4023 Energy Saving and Management 3 2 0 3 5 BDE 4033 Turbo Machinery 3 2 0 3 5 BDE 4043 Computational Fluid Dynamics 3 2 0 3 5 BDE 4053 Hydraulics Power 3 2 0 3 5 BDE 4063 Internal Combustion Engine 3 2 0 3 5
BDE 4073 Safety and Maintenance Engineering
3 2 0 3 5
BDE 4083 Aerodynamics 3 2 0 3 5 BDE 4093 Thermal Environment Design 3 2 0 3 5
Textile Elective
BDF 4013 Textiles Material Science 3 2 0 3 5 BDF 4023 Yarn Manufacturing Technology 3 2 0 3 5 BDF 4033 Fabric Manufacturing Technology 3 2 0 3 5 BDF 4043 Weaving Engineering 3 2 0 3 5 BDF 4053 Textiles Dyeing and Finishing 3 2 0 3 5 BDF 4063 Textiles Materials Testing 3 2 0 3 5
BDE 4073 Safety and Maintenance Engineering
3 2 0 3 5
Packaging Elective
BDG 4013 Packaging Engineering Principles 3 3 0 3 6 BDG 4023 Packaging Equipments 3 3 1 3 7 BDG 4033 Packaging System I 3 2 0 3 5 BDG 4043 Packaging System II 3 2 0 3 5 BDG 4053 Packaging System Development 3 2 0 3 5 BDG 4063 Packaging Dynamics 3 2 0 3 5
BDE 4073 Safety and Maintenance Engineering
3 2 0 3 5
7
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
Matrix of Programme Learning Outcome - Subjects
Code Subjects
Programme Learning Outcomes
LO1 LO2 LO3 LO4 LO5 LO6 LO7 LO8 LO9 LO10 LO11
1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2
BDA 1012 Engineering Drawings x x x x x x x BDA 1023 Static
x x x x x x x
BDA 1032 Material Sciences x x x x x x x x x x x x BDA 1042 Mechanics of Solid I
x x x x x
BDA 1052 Fluid Mechanics I x x x x x x x x x x x BDA 1701 Engineering Lab I
x x x x x x x x
BDA 1801
Mechanical Engineering Practice I
x
x
x x x
x
x
x
BDA 1811
Mechanical Engineering Practices II
x
x
x x
x
x
x
x
BDA 2013 Dynamics
x x x x x x x x x
BDA 2022 Thermodynamics I x
x
x
x
x
x
x
x
BDA 2033 Mechanics of Machine
x x x x x x x x x x x
BDA 2042
Engineering Materials Selection x x x x x x x
BDA 2052 CAD and Modelling x x x x x x x x x x x x BDA 2701 Engineering Lab II x
x
x
x
x
x x
x
x x
BDA 2711 Engineering Lab III
x x x x x x x x
BDA 2721 Engineering Lab IV x
x
x
x
x
x x
x
x x
BDA 2801
Mechanical Engineering Practices III
x x x x x x x
BDA 2811
Mechanical Engineering Practices IV
x x x x x x x x x x x
BDA 3023 Fluid Mechanics II x x x x x x x x BDA 3033 Solid Mechanics II
x x
x
x x
x
8
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
BDA 3043 Thermodynamics II
x x x x x x x x x x
BDA 3052
Manufacturing Technology x x x x x x x x x x x
BDA 3053
Engineering Economics and Entrepreneurship
x x x x x x x
BDA 3063 Heat Transfer x
x
x x x x x
x
x x
x
BDA 3073 Control Engineering
x
x
x
x
x
x
x
x
x
BDA 3083 Mechanical Design I x x x x x x BDA 3701 Engineering Lab V x x x x x x x x x x BDA 3711 Engineering Lab VI x
x x x x x x x x x x x x x x x x x
BDA 4012 Industrial Engineering x
x
x x
x
x
x x
x
x
BDA 4023
Mechanical Engineering Design II
x x x x x x x x x
BDA 4033 Finite Element Method
x x x x x x x x x
BDA 4042
Management and Professional Ethics
x
x x
x
x
x x x
x x
x
BDA 4052 Engineers and Society
x x
x x
x x x x x
x x x
x
BDA 4804
Industrial Training(3 Months)
x x x x x x x x x x x x x x x
BDA 4902 Bachelor Project I
x x x x x x x x x x x x x
BDA 4904 Bachelor Project II
x x x x x x x x x x x x x x
BDB 4013
Thermodynamics of Materials x x x x x x x x x x
BDB 4023 Material Testing x x x x x x x x x BDB 4033 Mechanical Metallurgy x x x x x x BDB 4043
Corrosion and Prevention x x x x x x x x x
BDB 4053 Applied Metallurgy x x x x x x x BDB 4063 Polymer and Ceramics x x x x x x x x x x BDB 4073 Composite x x x x x x x x x x BDB 4083 Advanced Materials x x x x x x x x
9
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
BDC 4013 Noise and Vibration
x x
x x
x x x x
x
x
x
BDC 4023 Control System Design
x x x x x x x
BDC 4033 Stress Analysis
x x x x x x x x
BDC 4043
Kinematics of Mechanism
x x x x x x x x
BDC 4053
Fatigue and Fracture Mechanics
x x x x x x x x
BDC 4063 Tribology
x x x x x x x
BDC 4073 Robotics
x x x x x x x x x x
BDC 4083
Modelling and Simulation
x x x x x x x x x x
BDD 4013
Design for Manufacturing and Assembly x x x x x x x x x x
BDD 4023
Computer Aided Design and Manufacturing x x x x x x x x
BDD 4033
Manufacturing and Rapid Development
BDD 4043 Rapid Manufacturing x x x
x x x
x
x x x
BDD 4053
Concurrent and Reverse Engineering x x x x
x x
x
x x
x
BDD 4063 Metal Casting Process x x
x
x x
x
x
x
BDD 4073 Advanced Machining x x x x x x x x x x x x x BDD 4083
Manufacturing Control Technology x x x x x x x x x x x
BDE 4013
Refrigeration and Air-conditioning System
x x x x
BDE 4023
Energy Saving and Management
x x x x
BDE 4033 Turbo Machinery
x x x x
BDE 4043
Computational Fluid Dynamics
x x x x
BDE 4053 Hydraulics Power
x x x x
BDE 4063
Internal Combustion Engine
x x x x
BDE 4073
Safety and Maintenance
x x x x
10
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
Engineering
BDE 4083 Aerodynamics
x x x x
BDE 4093
Thermal Environment Design
x x x x
BDF 4013
Textiles Material Science x x x x x x
BDF 4023
Yarn Manufacturing Technology x x x x
BDF 4033
Fabric Manufacturing Technology x x x x
BDF 4043 Weaving Engineering x x x BDF 4053
Textiles Dyeing and Finishing x x x x
BDF 4063
Textiles Materials Testing x x x x
BDG 4013
Packaging Engineering Principles
x x x x x
BDG 4023 Packaging Equipments
x
x
x
BDG 4033 Packaging System I
x x x
x
BDG 4043 Packaging System II
x
x
x
BDG 4053
Packaging System Development
x
x
x x x
BDG 4063 Packaging Dynamics
x
x
x x
Graduation requirement Requisite for graduation;
1. Application for graduation is done by the student and must be certified by faculty. 2. Passed all required subjects according to the program needs. 3. Accumulate the required credit and acquire the “KB (kedudukan baik)” status. 4. Achieve at least a distinction in Malay Language at the SPM level. 5. Application for graduation must be made by filling out the relevant forms within the specified period. 6. Must be approved and verified by Senate.
Employment Opportunities Employment opportunities for graduates as a mechanical engineer are very wide, either locally or internationally. The industrial training that graduates had gone through will put them in a strong position to contribute greatly in thier chosen field. Generic skills inculcated throughout the duration of the programme also makes graduates more rounded in their outlook. Those interested in research, have the opportunity to contribute in the various research institution throughout the world. Apart from that, post graduates studies are also available to graduates,
11
FACULTY OF MECHANICAL AND MANUFACTURING ENGINEERING UNIVERSITI TUN HUSSEIN ONN MALAYSIA PROGRAMMES SPECIFICATION
locally or internatinally, if they acquire excellent academic achievements. Related information (Lectures / Facilitators / Projects /Target group / Fees / etc.) 1. Academic Staff
i. Lecturers for university’s compulsary subjects are from Centre of Science Studies (PPS), Centre of Communication and Humanities Studies (PPKK), and Centre of Co-Curricular, Sports and Culture (PKSK). Meanwhile, lecturers for core subjects of this programme are from the faculty itself.
ii. Engineering Practice subjects will be taught by instructors/facilitators with wide working experience in the
industries. 2. Concept of Education
This programme is a practice-oriented programme with Outcome Base Education (OBE) concept, where students will undergo the theoretical and practical training of 8 semesters in university and 12 weeks of industrial training.
3. Fees
The fees for this programme is RM 510.00 (one time fee) and RM 1908.00 (recurring fee for every semester)
4. The faculty’s PROFORMA is available in www.uthm.edu.my
Prepared by : ………………………………………………….. Profesor Hj. Mohd Imran b. Hj. Ghazali Deputy Dean (Academic and Internationalization) Faculty of Mechanical and Manufacturing Engineering Universiti Tun Hussein Onn Malaysia Tel: 07-4537710
Verified by : ………………………………………………….. Prof. Dr. Sulaiman bin Hj. Hasan Dean Faculty of Mechanical and Manufacturing Engineering Universiti Tun Hussein Onn Malaysia Tel: 07-4537700
Date : June 2009 Date: June 2009 Note: Information is valid at printing and can be changed from time to time